www.edc.sanyo.com
2007-10
Solid Electrolytic Capacitors
with Polymerized Organic Semiconductor
Solid Electrolytic Capacitors
with Polymerized Organic Semiconductor
This catalog was produced in October 2007.Product names and specifications are subject to
change and products themselves are subject to discontinuation without prior notice. Be sure
to check the specifications before using your product.
Products described herein are not intended for applications requiring extremely high reliability
(for example, those in which extensive human injury or property damage may occur such as
with life-support systems or aircraft control systems). For such applications,consult our sales
department.
This document defines performance,characteristics and functions of each product under pre-
determined conditions.It does not guarantee performance,characteristics and functions when
used in customer systems.Be sure to check your system before using the product for possible
problems or occurrences that cannot be detected during the evaluation testing of each prod-
uct.
Electronic Device Company has full confidence in the quality and reliability of its prod-
ucts.However,misuse can result in personal injury,fire or other property damage. For ques-
tions regarding usage,please contact our sales department.
Should you wish to export any product that is listed as regulated goods (including services)
under the Foreign Exchange and Foreign Trade Law, an export license is required before ex-
porting .
This document may not be reprinted or reproduced in part or whole without the permission of
Electronic Device Company.
Electronic Device Company shall not be held responsible for any problems affecting a third
party's industrial property arising from use of these products unless such problems are
caused by structural or manufacturing flaws.
Please make note that all models from TPA, APA, APB series as well as the 16V TPB·
TPC series, some models of the TPD series are being integrated into the following series.
PRECAUTIONS
Series integration
Discontinued series Integrated series
TPA TPB
APA APC
APB APD
TPB(16TPB47M,16TPB47ML) TQC(16TQC47M)
TPC(16TPC33M) TQC(16TQC33M)
10TPD150M 10TPF150ML
6TPD330M 6TPF330ML
6TPD220M 6TPF220ML
4TPD470M 4TPF470ML
4TPD330M 4TPF330ML
2R5TPD680M 2R5TPF680ML
2R5TPD680M8 2R5TPF680M8L
2R5TPD470M 2R5TPF470ML
2R5TPD470M8 2R5TPF470M8L
INDEX
SANYO POSCAP CAPACITORS
● POSCAP is uniquely structured solid electrolytic capacitor.
●
Please note the operating precautions in order to take full advantage of
the POSCAP's performance and ensure the most stable quality possible.
Product guide
Product Line-up Table
Out Line
Series System Diagram
Products List
Guidelines and Precautions for Use
Environmental Consideration
Marking
Explanation of Part Numbers
Structure
Taping Specifications
Recommended Land Pattern Dimension
Recommended Soldering Condition
Characteristics
Specifications of POSCAP in Series
Adoption Example
2
3
4
6
8
11
12
13
14
15
16
17
18
44
TPB Series
TPB Series B2 size
TPC Series
TPC Series B1 size
TPD Series
TPE Series D2E,D3L,D4 size
TPE Series C3,C2,B2 size
TPF Series
TPG Series
TPL/TPLF Series
TPU Series
TA Series
TH Series
TR Series
TQC Series
APC/APD Series
20
22
24
26
27
28
30
32
33
34
36
37
38
40
42
43
2
Series Characteristics
High Capacitance
Low ESR
Small size
Low Profile
Low ESL
High Reliability
High Voltage
Page
Category
temperature
range (
°C
)
Rated Voltage
range
(V.DC)
Capacitance
range
(µF)
TPB
TPC
TPD
TPE
TPF
TPG
TPL
TPLF
TPU
TA
TH
TR
TQC
APC
APD
Standard Products
Low Profile Products
Low ESR . High Capacitance Products
Low ESR Products
Low ESR . High Capacitance Products
Small Size . High Capacitance Products
Low ESR . Low ESL Products Face Down Terminal Type
Low ESR . Low ESL Products Face Down Terminal Type
Small Size . Low Profile Products Face Down Terminal Type
High Reliability Products (For The Car Electronics)
125°C Guaranteed Products
High Moisture Resistance Products
High Voltage Products
Aluminum Anode Products
Aluminum Anode . Low Profile Products
--55 to +105
--55 to +105
--55 to +105
--55 to +105
--55 to +105
--55 to +105
--55 to +105
--55 to +105
--55 to +85
--55 to +105
--55 to +125
--55 to +105
--55 to +105
--55 to +105
--55 to +105
033 to 1000
10 to 330
470 to 1000
047 to 1500
150 to 6800
33 to 2200
220 to 4700
220 to 4700
10 to 1000
47 to 680
068 to 1000
33 to 680
5.6 to 680.
10 to 330
10 to 150
2.5 to 10
2.5 to 12.5
2.5 to 6.3
2 to 10
2 to 10
2.5 to 12.5
2.5
2
2.5 to 10
2.5 to 10
2.5 to 10
2.5 to 10
16 to 25
4 to 6.3
4 to 6.3
20
24
27
28
32
33
34
34
36
37
38
40
42
43
43
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Product Line-up Table
Product
Line-up Table
3
"POSCAP" is a solid electrolytic chip capacitor. The
Anode is sintered Tantalum and the Cathode is a
highly conductive polymer formed on SANYO
Original method.
"POSCAP" has a Lowest E.S.R. (Equivalent Series
Resistance) level and excellent performance for high
frequency though low profile and high capacitance.
In addition, it has high reliability and high heat
resistance.
Therefore, "POSCAP" is an ideal chip capacitor
especially for digital, high frequency devices.
Lead free
Terminal plating is Palladium and Gold. It's completely lead free.
Low profile chip capacitor
Low impedance and low ESR at high frequency
High ripple current capability
Long Life 105°C×2,000Hrs*
Excellent noise-absorbent characteristics
Excellent temperature characteristics up to –55°C
The rush current is guaranteed for 20A
Superior to Ta-Cap in safety
*A part of the model is excluded.
DC/DC Converter
Personal Computers
VCR, Camcorder, Digital Still Camera
Portable Communications Devices and Base Station
PDA (Portable terminals, etc.)
Navigation System
HD Drive, MO Drive, DVD Drive
Features
Applications
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Out Line
Out Line
4
P.33
P.24-26
TPC
Low Profile Products
TPG
Small Size·High
Capacitance Products
2.5 to 10V
68 to 330µF
2.5 to 8V
33 to 100µF
2.5 to 12.5V
10 to 56µF
4 to 6.3V
150 to 220µF
2.5 to 12.5V
33 to 220µF
D2 size
C1 size
B1 size
B15G size
B1G size
P.20-23
TPB
Standard Products
2.5 to 10V
220 to 1000µF
2.5 to 10V
100 to 330µF
2.5 to 10V
100 to 680µF
2.5 to 10V
47 to 220µF
2.5 to 10V
33 to 220µF
D4 size
D3 size
D3L
size
C size
B2 size
P.28-31
TPE
Low ESR Products
2.5 to 10V
330 to 1500
µ
F
P.27
TPD
D4D
size
Low ESR·High
Capacitance Products
2.5 to 6.3 V
470 to 1000
µ
F
2.5 to 10V
220 to 680µF
2.5 to 10V
68 to 470µF
2.5 to 10V
150 to 330µF
2.5 to 8V
100 to 330µF
2 to 10V
47 to 330µF
D4 size
D3L size
D2E size
C3 size
C2 size
B2 size
P.43
APC
D2 size
Aluminum Anode
Products
4 to 6.3V
10 to 33µF
P.43
APD
D1 size
Aluminum Anode·
Low Profile Products
4 to 6.3V
10 to 15µF
TPU
4 to 8V
33 to 68µF
10V
33µF
2.5 to 6.3V
22 to 47µF
2.5 to 6.3V
10 to 22µF
B09 size
A09 size
S11 size
S08 size
P.36
Small Size
·
Low Profile Products
Face Down Terminal Type
Series System
Diagram
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Series System Diagram
5
P.37
TA
High Reliability Products
(For The Car Electronics)
P.34-35
TPL
D2T size
Low ESR·Low ESL Products
Face Down Terminal Type
2.5V
220 to 470µF
P.34-35
TPLF
D2T size
Low ESR·Low ESL Products
Face Down Terminal Type
2V
220 to 470µF
2.5 to 10V
150 to 680µF
2.5 to 10V
68 to 470µF
4 to 10V
47 to 100µF
D3L size
D2E size
B2 size
P.42
TQC
High Voltage Products
16 to 25V
33 to 68µF
16 to 25V
15 to 47µF
16 to 25V
10 to 22µF
16 to 25V
5.6 to 10µF
D3L size
D2 size
C size
B2 size
P.38-39
TH
125˚C Guaranteed
Products
P.32
TPF
D3L size
Low ESR·High
Capacitance Products
2.5 to 10V
100 to 680µF
D2E size
2V
220 to 470µF
2.5 to 6.3V
330 to 680µF
2.5 to 10V
220 to 1000µF
2.5 to 10V
100 to 470µF
2.5 to 6.3V
68 to 220µF
2.5 to 8V
150 to 330µF
D4D
size
D4 size
D3L size
D2 size
D2E size
P.40
TR
High Moisture
Resistance Products
2.5 to 10V
150 to 680µF
2.5 to 10V
68 to 470µF
D3L size
D2E size
2.5 to 10V
33 to 220µF
B2 size
6.3V
150µF
B15 size
NEW
The size of each photo is close to full scale.
Series System
Diagram
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Series System Diagram
6
*Under development *1(F:15, I:18, M:25) *2(C:12, F:15, I:18, M:25) *3(9, C:12, F:15, I:18, M:25)
*4(5, 6, 8, 10)
•Symbols in table:Case Size
•( ):ESR specitication(mΩmax.)
Series
WV 2.2 4.7 5.6 6.8 8.2 10 15 22 33 47 56
TPE
TPE
TPF
TPLF
TPB
TPB
TPC
TPD
TPE
TPE
TPE
TPE
TPF
TPG
TPL
TPU
TPU
TPB
TPB
TPB
TPC
TPC
TPD
TPE
TPE
TPE
TPE
TPF
TPG
TPU
TPU
APC
APD
TPB
TPB
TPB
TPC
TPC
TPD
TPE
TPE
TPE
TPE
TPF
TPG
TPU
TPU
APC
APD
TPB
TPC
TPE
TPG
TPU
TPB
TPB
TPC
TPE
TPF
TPG
TPU
TPC
TPG
TQC
TQC
TQC
TQC
2V
2.5V
3.15V
4V
6.3V
8V
10V
12.5V
16V
20V
25V
µF
Series
B1(70)
C1(70)
S11(150)
D2(40)
B1(70)
B2(70)
C1(70)
B09(70)
B2(70)
B1(70)
B1G(70)
A09(150)
B1G(70)
D2(70)
D2(45)
D3L(60)
S11(150)
B1(70)
B2(70)
B1(70)
B09(70)
A09(150)
B2(70)
B1G(70)
C(55)
B2(70)
B2(35)
B1G(70)
D2(70)
D3L(45)
D3L(55)
S08(250)
D2(70)
D1(70)
B1(80)
B2(100)
C(95)
B2(100)
B2(100)
S08(250)
S11(150)
D2(40)
B1(70)
C(80)
D2(80)
D2(90,45)
S08(250)
D1(70)
B1(80)
C(80)
D2(90,45)
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Products List
Products List
7
Case size (unit:mm)
L
W
H
S08
2.0
1.25
0.8
S11
2.0
1.25
1.1
A09
3.2
1.6
0.9
B09
3.5
2.8
0.9
B1
3.5
2.8
1.1
B1G
3.5
2.8
1.1
B15G
3.5
2.8
1.4
B2
3.5
2.8
1.9
C1
6.0
3.2
1.4
C2
6.0
3.2
1.8
C3
6.0
3.2
2.5
C
6.0
3.2
2.8
D1
7.3
4.3
1.4
D2E
7.3
4.3
1.8
D2T
7.3
4.3
1.8
D2
7.3
4.3
1.9
D3L
7.3
4.3
2.8
D3
7.3
4.3
3.1
D4D
7.3
4.3
3.6
D4
7.3
4.3
3.8
WV 68 82 100 120 150 220 330 470 680 1000 1500
TPE
TPE
TPF
TPLF
TPB
TPB
TPC
TPD
TPE
TPE
TPE
TPE
TPF
TPG
TPL
TPU
TPU
TPB
TPB
TPB
TPC
TPC
TPD
TPE
TPE
TPE
TPE
TPF
TPG
TPU
TPU
APC
APD
TPB
TPB
TPB
TPC
TPC
TPD
TPE
TPE
TPE
TPE
TPF
TPG
TPU
TPU
APC
APD
TPB
TPC
TPE
TPG
TPU
TPB
TPB
TPC
TPE
TPF
TPG
TPU
TPC
TPG
TQC
TQC
TQC
TQC
2V
2.5V
3.15V
4V
6.3V
8V
10V
12.5V
16V
20V
25V
µF
Series
B2(70)
B09(70)
A09(150)
B2(70)
C1(55)
B1G(70)
C(55)
D2(45)
D2E(25)
D3L(50)
D4(30)
D3L(40)
D4D(*4)
D3L(*2)
D3L(10,7,6)
D4(35)
D4D(10)
D4(*1)
D4(25,18)
D4(30)
D4D(*4)
D4(*1) D4(15,12)
C1(70)
C(45)
B2(35)
B2(70)
A09(150)
A09(150)
B2(70,45)
C1(55)
B2(35)
B2(55, 45)
C(45)
C1(55)
D2(45)
D2E(25,18)
B2(35,25)
B1G(70)
C2(25)
D3(55)
D3L(55)
D2(45)
B2(35)
C(45)
B2(70)
D2(45)
D2E(25,18)
B2(35,30)
B1G(70)
D3(55)
D3L(55)
C(45)
D2(40)
D2E(25,18)
C3(25)
C2(25,18)
B2(35)
B15G(70)
D2(40)
D3L(40)
C3(55)
D3L(15)
D2E(6)
D2T(7,6)
C(45)
B2(55)
D2(45)
D2E(*3)
B2(35,25,21,18)
B2(15)*
B1G(70)
D2T(12)
C(45)
D3(65)
D3L(55)
D2(40)
D2E(*1)
B2(35)
C2(18,15)
C3(25,18)
B15G(70)
D3L(40)
D2E(25,18)
D2E(25)
C3(25)
D3L(12)
D4(40)
D3L(40)
D3L(25)
B2(18)
B2(15)*
D2E(6)
D2T(7,6)
D3(65)
D3L(55)
D2(40)
C2(15,12, 9)
D2E(*3)
B2(35)
C3(*1)
D3L(7)
D2T(12,9,8,7)
D3L(40)
D2E(25,18)
D3L(12)
D3L(40)
D4(40)
D2(40)
D4D(10)
D2E(25)
D3L(25,18)
D3L(9)
D4(35)
D4(25)
D2E(6)
D2T(7,6)
D3L(40)
D4D(*4)
D2E(*3)
D3L(10,7)
D2T(12,9,8,7)
D4(40)
D3L(40)
D3L(*2)
D3L(10)
D4(35)
D4(25,18)
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Products List
Products List
8
(1) Polarity
POSCAP is a conductive polymer capacitor with positive and negative electrodes. Do not
reverse the polarity when using. If it is used with the polarities reversed, increased leakage
current or a short circuit may result.
(2) Prohibited circuits
Since problems can be expected, the POSCAP cannot be used on the following circuits.
(1) High impedance voltage retention circuits
(2) Coupling circuits
(3) Time constant circuits
(4) Circuits greatly affected by leakage current
(5) The circuit in which two or more POSCAP are connected in a series so as to raise the
endurance voltage.
(3) Over voltage prohibited during design
Over voltage exceeding the rated voltage may not be applied even for an instant as it may
cause a short circuit.
(4) Sudden charge and discharge restricted
Sudden charge and discharge are restricted (for maintainance of high-proof reliability).
A protection circuit is recommended for when a sudden charge or discharge causes
excessive rush current since this is main cause of short circuit and large leakage current.
Use protection circuits in case the rush current value exceeds 20A.
Be sure to insert a protection resistor of about 1kΩ for charge and discharge when
measuring the leakage current.
(5) Considerations when soldering
The soldering conditions are to be within the range prescribed in this delivery specification. If
the specifications are not followed, there is the possibility of the appearance becoming
defective when soldering is conducted under conditions that are harsher that those stipulated.
(6) Considerations when using in industrial equipment
To insure reliability when POSCAP is used in industrial equipment, allow wider margin of
capacitance, impedance and other characteristics.
(7) Using in equipment regarding human life
In case of using in equipment regarding human life (e.g. Space equipment, aeronautic
equipment, military equipment and atomic equipment etc.), be sure to talk over the matter
with SANYO.
Don't use without a recognition document of SANYO.
(1) Check the rated performance
After checking the operation and installation environments, design the circuit so that it falls
whithin the rated performance range stipulated in this delivery specification.
(2) Operating temperature and ripple current
(a) Set the operating temperature so that it falls whithin the range stipulated in this delivery
specification.
(b) Do not supply current that exceeds the allowable ripple current. When excessive ripple
current is supplied, internal heat increases and reduces the POSCAP's life span.
POSCAP is uniquely structured solid electrolytic capacitor.
Please note the following points in order to take full advantage of the POSCAP's
performance and ensure the most stable quality possible.
Crucial Precautions
Circuit designing cautions
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Guidelines and Precautions for Use
Guidelines and
Precautions for Use
9
Company name of a mention and product name are the trademark of each company or trade mark.
(3) Leakage current
Even when the soldering conditions fall whithin the range of this delivery specifications, leakage current
increases a little on occasion. It also increases a little during high temperature storage, high humidity
storage and temperature cycling with no voltage applied. In cases such as these, leakage current will
decrease by applying voltage under the condition of below the POSCAP's maximum operating temperature.
The speed at which the leakage current is restored is increased by applying voltage when the POSCAP's
temperature is close to the maximum operating temperature.
(4) Applied voltage for designing
(a) Less than 90% of the rated voltage or category voltage is recommended. If the rated voltage is 10V, and
over less than 80% of the rated voltage or category voltage is recommended.
(b) The sum of the DC voltage plus the peak AC voltage shall not exceed the rated voltage or category
voltage.
(c) The sum of the DC voltage plus the negative peak AC voltage shall not allow a voltage reversal.
(5) Reduction of failure stress
When POSCAP is used within the rated voltage , it shows a stable characteristic, but it may be damaged in
a short circuit when an overvoltage, for instance, is applied.
The time to reach the failure mode can be extended by using POSCAP with reduced ambient temperature,
ripple current and applied voltage.
[Failure rate]
¡In the case of the endurance which is 105°C×2,000h.
0.5%/1,000h (Environment temp. : 105°C, Rated voltage or Category voltage applied)
¡In the case of the endurance which is 105°C×1,000h or 125°C×1,000h.
1.0%/1,000h (Environment temp. : 105°C, Rated voltage or Category voltage applied)
¡In the case of the endurance which is 85°C×1,000h.
1.0%/1,000h (Environment temp. : 85°C, Rated voltage applied)
(6) Operating environment restrictions
Do not use the POSCAP in the following environments.
(a) Places where water, salt water or oil can directly fall on it and places where condensation may form.
(b) Places filled with noxious gas for capacitors (hydrogen sulfide, sulforous acid, chlorine, ammonia, etc.).
(c) Places susceptible to ozone,ultraviolet rays and radiation.
(7) Land pattern
When mounting the POSCAP on the PC board, match the POSCAP's land pattern dimension. (See P16.)
(8) Parallel connection
A large amount of ripple current may be applied to the POSCAP when it is used in parallel connection with
another capacitor.
Carefully select the type of capacitor.
(9) Protect circuit
The failure mode of POSCAP is the short mode. When it breaks down, short electric current flows to it.
POSCAP gives off heat by this short current. Do the following consideration in design fully for the safety
because it has a bad influence on the part around POSCAP due to this heat.
: A protection circuit and a protection device are set up, and it is made safer as a system.
: A diffuse circuit and so on is set up, and a safe system is taken so that a machine may
not break down as to the single trouble.
(10) Others
Design circuits after checking the following items.
Electrical characteristics are affected by temperature and frequency fluctuations.
Design circuits after checking the amount of fluctuation.
We are confident that the practical configurations and examples listed in this document will ensure the maximum benefit from the characteristics and
performance features of our products and that these application examples are accurate and reliable. However, we cannot accept any liability for any
problems in connection with industrial property rights and concerning any difficulties arising in the use of these circuits. It should also be noted that as
part of our ongoing policy of product improvement, the specifications given herein may be changed or modified at any time without prior
notice. Copyright, All or portions of this publication are protected against copying or other reproduction.
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Guidelines and Precautions for Use
Guidelines and
Precautions for Use
10
(1) Please make the storage of POSCAP sealing up in the reel and storage bag.
(2) Do not store the POSCAP at high temperature and high humidity.
Store it in a location that is not subject to direct sunlight, has temperatures less than 35°C (Generally 15
to 35°C), and relative humidity less than 75%RH (45 to 75%RH) generally.
(3) The storage period is one year or shorter under the condition that it is un opened the storage bag.
(TQC series : 9 months from the pass mark on the label)
(4)
Do not store the POSCAP in damp conditions such as with water, salt spray, or oil spray, and dew
condensation.
(5) Do not store the POSCAP in places filled with noxious gas (hydrogen sulfide, sulfurous acid, nitrous acid,
chlorine, ammonia, etc.).
(6) Do not store the POSCAP in places susceptible to ozone, ultraviolet rays and radiation.
(7) Please unseal storage bag just before mounting and be conscious that POSCAP not remain. When
remainder occurs reluctantly, return them to storage bag once again and, please seal the unsealing division
by adhesive tape etc., including desiccants. More over, once open the strage bag, it should be followed the
table of (8),s Floor Life "Time" and "condtions".
(8) The moisture level of POSCAP is the following.
NOTE:The model of MSL "2a" is changed into MSL "3"
with the 260°C reflow soldering.
LEVEL Floor Life Applicable scope
(Conform to IPC/JEDEC J-STD-020C)
*Use at 105°C or less
Time
4 weeks
168hours
72hours
48hours
2a
3
4
5
Conditions
≤ 30°C/60%RH
≤ 30°C/60%RH
≤ 30°C/60%RH
≤ 30°C/60%RH
Size code
D2E,D2,D2T,
D3L,D3,D4,D4D
S08,S11,A09,B09,
B1,B1G,B15G,B2,C1,C3,C,C2
D2
D1,D2E,D2,D3L,D4
Series
TPB,TPC,TPE,TPD,
TH*,TPL,TPLF
TPB,TPC,TPE,TPG,
TPU,TA,TQC (All sizes)
APC
TH,APD
Storage Conditions
It is necessary to set an environment to prevent a trouble at the time of soldering by the degradation
of solder ability or moisture's getting into the molding resin when POSCAP are stored.
Frequency compensation coefficient
(TPB,TPC,TPD,TPE,TPF,TPG,TPL,TPLF,TPU,TA,THseries)
Temperature compensation coefficient
(TPB,TPC,TPD,TPE,TPF,TPG,TPL,TPLF,TPU,TA,TH,APseries)
T≤45°C
45°C<T≤85°C
*85°C<T≤105°C
S08, S11, A09, B09, B1,B1G,B15G, B2, C, C1, C2, C3, D2, D2E, D2T, D3L, D3, D4(THD), D4D
1.00
0.70
0.25
Case size code
D4
1.00
0.50
0.25
T :Environment temperature
*THseries :85°C<T≤125°C
It takes advantage in ripple current value of characteristics list and the following coefficient.
(For questions regarding TQC series, please ask separately.)
120Hz≤f<1kHz
0.20
0.25
0.30
1kHz≤f<10kHz
0.60
0.70
0.75
10kHz≤f<100kHz
0.85
0.85
0.90
100kHz≤f<1MHz
1.00
1.00
1.00
22µF≤C≤100µF
100µF≤C≤330µF
330µF≤C≤1000µF
Compensation coefficient of maximum allowable ripple current
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Guidelines and Precautions for Use
Guidelines and
Precautions for Use
11
RoHS Compliance
POSCAP is compliant to the RoHS Directive(2002/95/EC),
Restricted substances of RoHS directive
Lead-Free Status
All complete parts and homogenous materials of POSCAP are lead-free.
Halogen-Free
TPG, TPL and TPU series are the halogen-free products which use non-halogen material as molding resin.
We are planning to remove halogenated material from other series, too.
*Halogen-free POSCAP is also compliant with RoHS directive and lead-free.
Substance
Lead (Pb) and it's compounds
Cadmium (Cd) and it's compounds
Mercury (Hg) and it's compounds
Hexavalent chromium (Cr6+)
Polybrominated biphenyls (PBBs)
Polybromineted diphenyl ethers (PBDEs)
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Environmental Consideration
Environmental
Consideration
12
680
e57
470
eL58
E8
eF
jAH
S7
jG
330
55
eT
C2,C3,D2E,D3L size (TPB,TPE,TPF series)
D4,D4D size (TPD,TPE series)
Rated capacitance
Anode(+)
Rated voltage*1
Lot. No.*2
L
F
D
TPB series
D3L size
TPF series
TRD series
B09,B1,B1G,B15G,B2 size
(TPB,TPG,TPU,TQC series)
Anode(+)
Rated capacitance*3
Lot. No.*2
Rated voltage*1
Rated capacitance
Lot. No.*2
Anode(+)
Rated voltage*1
C,C1,D2,D3,D4 size (TPB,TPC,TH series)
C,D2,D3L size (TQC series)
D1,D2 size (APC,APD series)
B2 size (TPE series)
Anode(+)
Rated capacitance*3
Lot. No.*2
Rated voltage*1
Anode(+)
Lot. No.*2
S08,S11,A09 size (TPU series)
Rated capacitance*4
Rated voltage*1
D2T size (TPL,TPLF series)
Anode(+)
Rated voltage*1
Lot. No.*2
*3 The rated capacitance is as follows.
*1 The rated voltage is as follows.
*2 Lot.No.shows roughly manufacturing date.
Capacitance(µF)
Mark
47
S7
56
U7
33
N7
10
A7
22
J7
5.6
U6
8.2
Y6
68
W7
100
A8
150
E8
120
C8
220
J8
330
N8
R.V.
Mark
8.0
K
10
A
6.3
j
3.15
f
4.0
g
2.0
d
2.5
e
12.5
B
16
C
25
1E(orE)
R. Cap.(µF)
Mark
68
W
100
A
47
S
22
J
33
N
10
A
15
E
*4 The rated capacitance is as follows.
Rated capacitance*3
T
F
TPL series
TPLF series
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Marking
Marking
13
ZB
UB
PB
LB
IB
FB
FGB
AZB
AUB
APB
AFB
AFGB
PC2
IC2
FC2
CC2
9C2
GC
ZC
PC
IC
FC
AP
L
IL
FL
CL
ESR 35mΩ Max.
ESR 30mΩMax.
ESR 25mΩ Max.
ESR 21mΩ Max.
ESR 18mΩ Max.
ESR 15mΩ Max.
ESR 15mΩ /300KHz Max.
ESR 35mΩ Max. 85°C
ESR 30mΩ Max. 85°C
ESR 25mΩ Max. 85°C
ESR 15mΩ Max. 85°C
ESR 15m
Ω
/300KHz Max.
85°C
ESR 25mΩ Max.
ESR 18mΩ Max.
ESR 15mΩ Max.
ESR 12mΩ Max.
ESR 9mΩ Max.
ESR 55mΩ Max.
ESR 35mΩ Max.
ESR 25mΩ Max.
ESR 18mΩ Max.
ESR 15mΩ Max.
ESR 25mΩ Max. 85°C
ESR 25mΩ Max.
ESR 18mΩ Max.
ESR 15mΩ Max.
ESR 12mΩ Max.
B2 size
C2 size
C3 size
D2E size
D3L size
CodeStandard
TPB Series
A
V
AV
C
L
B
C
9L
7L
SK
AI
BI
V
Z
I
F
C
9
8
6
5
B2 Size
D3L Size
85°C
ESR 45mΩ Max.
ESR 45mΩ Max. 85°C
CodeStandard
TPE Series
C size
D3L size
TPC Series
B1 size
C1 size
TPF Series
ESR 9mΩ Max.
ESR 7mΩ Max.
TPU Series
S11 size
A09 size
B09 size
All Series
ESR 45mΩ Max.
ESR 35mΩ Max.
ESR 18mΩ Max.
ESR 15mΩ Max.
ESR 12mΩ Max.
ESR 09mΩ Max.
ESR 08mΩ Max.
ESR 06mΩ Max.
ESR 05mΩ Max.
Use the following example to define POSCAP part numbers.
2R5 TPB 330 M L
Rated voltage
1 to 3 figures
Series name
3 figures
Rated capacitance
2 to 4 figures
Capacitance tolerance
1 figure
Special code
0 to 3 figures
Rated
voltage
2.0
2.5
3.15
4.0
6.3
8.0
10
12.5
16
20
25
Code
2
2R5
3
4
6
8
10
12
16
20
25
Capacitance
tolerance
±20%
Code
M
Rated
capacitance
5.6
8.2
10
15
22
33
47
56
68
82
100
150
220
330
470
680
1000
1500
Code
5R6
8R2
10
15
22
33
47
56
68
82
100
150
220
330
470
680
1000
1500
Code
TPB
TPC
TPD
TPE
TPF
TPG
TPL
TPLF
TPU
TAB
TAC
TAD
TAE
THB
THC
THD
THE
TQC
APC
APD
Series
TPB Series
TPC Series
TPD Series
TPE Series
TPF Series
TPG Series
TPL Series
TPLF Series
TPU Series
TAB Series
TAC Series
TAD Series
TAE Series
THB Series
THC Series
THD Series
THE Series
TQC Series
APC Series
APD Series
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Explanation of Part Numbers
Explanation of
Part Numbers
14
TPB,TPC,TPE,TPF,TQC,TA,TH series
TPL,TPLF series
TPU series
AP series
Sintered Tantalum Ag-paint layer Carbon layer
Tantalum oxide layer Anode(+)
Cathode(–)
Silver paint
Mold resin
Conductive Polymer
Sintered Tantalum
Silver paint
Mold resin
Cathode(–)
Ag-paint layer
Carbon layer
Conductive
Polymer
Tantalum oxide
layer
Anode(+)
Aluminum foil Ag-paint layer
Silver paint
Mold resin
Metal foil
Cathode(–)
Conductive
Polymer
Insulation
adhesive
Aluminum oxide
layer
Anode(+)
Sintered Tantalum Ag-paint layer Carbon layer
Tantalum oxide layer Anode(+)
Cathode(–)
Silver paint
Mold resin
Conductive Polymer
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Structure
Structure
15
c
a
b
Sprocket hole
J
A
F
K
t
GH
DE
C
Component compartment
(Polarity)
Direction of unreeling
(–)
(+)
B
Size
code
S08
S11
A09
B09
B1
B1G
B15G
B2
C1
C2
C3
C
D1
D2E
D2T
D2
D3L
D3
D4
D4D
2.4
2.25
3.65
3.8
3.8
3.9
3.9
3.8
6.4
6.4
6.4
6.4
7.65
7.5
7.8
7.5
7.7
7.5
7.7
7.7
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
φ1.5
J
+0.1
–0
1.0
1.3
1.3
1.4
1.4
1.7
1.7
2.1
1.7
2.1
2.9
3.2
1.6
2.4
2.4
2.4
3.2
3.5
4.2
4.2
0.25
0.25
0.25
0.2
0.2
0.25
0.25
0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
1.65
1.45
2.05
3.2
3.2
3.25
3.25
3.3
3.7
3.7
3.7
3.7
4.55
4.5
4.5
4.5
4.5
4.5
4.5
4.5
B
±0.1
C
±0.3
D
±0.1
E
±0.1
F
±0.1
G
±0.1
H
±0.1
K
±0.2
t
±0.1
A
±0.1
W2
W1
A
B
C
•
Dimension A and B are the measure of compartment's inside bottom.
•The (+) Polarity of the chip is placed on right side towards the
unreeling direction.
•Dimension of the topcover tape
Thickness of cover tape: 62±10µm
Width of cover tape: 9.5±0.2mm
5.5±0.2mm (φ180reel)
A
φ330±2
φ180
+0
–3
C
φ13±0.2
φ13±0.2
W1
13.5±0.5
9±0.5
W2
17.5±1.0
11.4±1.0
B
φ80±2
φ60±2
Size code
S08
S11
A09
B09
B1
B1G
B15G
B2
C1
C2
C3
C
D1
D2E
D2T
D2
D3L
D3
D4
D4D
Pieces/reel(φ330)
—
—
—
—
—
—
—
—
4000
3000
2500
2500
3000
3000
3000
3000
2500
2500
2000
2000
Pieces/reel(φ180)
4000
3000
3000
3000
3000
2500
2500
2000
—
—
—
—
—
—
—
—
—
—
—
—
Size code
S08
S11
A09
B09
B1
B1G
B15G
B2
C1
C2
C3
C
D1
D2E
D2T
D2
D3L
D3
D4
D4D
Pieces/case
20000
15000
15000
15000
15000
12500
12500
10000
20000
15000
12500
12500
15000
15000
15000
15000
12500
12500
10000
10000
*We supply only embossed taping type.
(unit:mm)
(unit:mm)
Dimension of carrier tape Packing quantities
Dimension of packing case
Units per packing case
Reel dimension
(unit:mm)
Reel size
a
b
c
φ330
120
360
360
φ180
90
240
240
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Taping Specifications
Taping
Specifications
(1) Three-pad design for three-terminal model (TPL/TPLF series)
16
(unit:mm)
aa
b
c
Size code
S08
S11
A09
B09
B1
B1G
B15G
B2
C1
C2
C3
C
D1
D2E
D2
D3L
D3
D4
D4D
b
0.9
0.9
1.2
2.7
2.7
2.7
2.7
2.7
2.3
2.3
2.3
2.3
2.9
2.9
2.9
2.9
2.9
2.9
2.9
c
0.6
0.6
1.2
1.4
1.4
1.4
1.4
1.4
2.4
2.4
2.4
2.4
3.7
3.7
3.7
3.7
3.7
3.7
3.7
a
1.0
1.0
1.6
1.6
1.6
1.6
1.6
1.6
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
Size code
D2T
A
1.7
B
1.2
C
2.7
D
3.2
E
5.1
F
0.7
G
1.3
H
0.45
I
0.9
J
0.75
K
0.9
L
1.1
M
0.3
N
1.4
O
1.0
P
2.15
Q
0.95
R
2.1
*Slash areas shows solder pads
(unit:mm)
G
E
B
AF C A
VIA(–) 8-φ0.4VIA(+) 8-φ0.4
Q
R
D
H
IJ
KL
MM
NO P
(2) Common three-pad design for POSCAP D-size two-terminal model
Size code
D common
A
2.2
B
1.2
C
2.7
D
2.9
E
5.1
F
0.5
G
1.0
H
0.45
I
0.9
J
0.75
K
1.4
L
1.1
M
0.3
N
1.4
O
1.0
P
2.15
Q
0.95
R
2.1
Except for TPL/TPLFseries
TPL/TPLFseries
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Recommended Land Pattern Dimension
Recommended
Land Pattern Dimension
17
Temperature on the surface of capacitor
90s max.180s max.
217°C
200°C
150°C
260°C
60s max.
6s max.
5s max.
Peak temperature
Time(sec.)
Peak temperature
5s max.
40s max.
30s max.
Time(sec.)
120s max.
220°C
180°C
150°C
250°C
60s max.
Temperature on the surface of capacitor
Peak temperature
5s max.
40s max.
30s max.
Time(sec.)
120s max.
150°C
200°C
240°C
60s max.
Temperature on the surface of capacitor
Peak temperature 260°C lead free reflow soldering profile
Soldering with a soldering iron
Peak temperature 250°C lead free reflow soldering profile
Tip of a soldering iron: 350°C Max. Power of a soldering iron: 30W Max. Working time: 3sec. Max.
(Do not let the tip of soldering iron touch the POSCAP itself. Do not subject the POSCAP itself to excessive stress when soldering.)
The cycles of reflow soldering: Twice (Max.)
The cycles of reflow soldering: Twice (Max.)
Recommended reflow soldering temperature profile
•The model of MSL"2a" is changed into MSL "3" with this reflow condition.(See P10)
The cycles of reflow soldering: Twice (Max.)
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Recommended Soldering Condition
Recommended
Soldering Condition
18
Temperature Characteristics
200
150
100
50
0
-50
-100
-150
-200
Temperature(:)
-55 -15 5 25 45 65 85 105-35
ESR change (%)
Temperature Characteristics (ESR)
MLCC 10µF16V Y5V
3.2
×
2.5
×
1.15mm
6TPB47M
100
80
60
40
20
0
-20
-40
-60
-80
-100
Temperature(:)
-55 -35 -15 5 25 45 65 85 105
Capacitance change (%)
Temperature Characteristics(Cap.)
MLCC 10 µF16V Y5V
3.2
×
2.5
×
1.15mm
6TPB47M
100
80
60
40
20
0
-20
-40
-60
-80
-100
Bias Voltage (V)
024 6
Capacitance change (%)
Bias voltage Characteristics (Cap.)
MLCC 10µF16V Y5V
3.2
×
2.5
×
1.15mm
6TPB47M
Bias voltage Characteristics
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Characteristics
Characteristics
19
Frequency(kHz)
ESR, Impedance(Ω)
10
100
1
0.1
0.01
TPE series
0.001
0.1 1 10 100 1000 10000
B2size(6TPE100MAZB)_Imp.
B2size(6TPE100MAZB)_ESR
C3size(6TPE150MPC)_Imp.
C3size(6TPE150MPC)_ESR
D2Esize(6TPE150MI)_Imp.
D2Esize(6TPE150MI)_ESR
D3Lsize(6TPE330MIL)_Imp.
D3Lsize(6TPE330MIL)_ESR
D4size(6TPE470MI)_Imp.
D4size(6TPE470MI)_ESR
TPD series
Frequency(kHz)
ESR, Impedance(Ω)
10
100
1
0.1
0.01
0.001
0.1 1 10 100 1000 10000
SIZE:D4
W
7.3×4.3×3.8
HL
2R5TPD470M5(2.5V/470µF)_Imp.
2R5TPD470M5(2.5V/470µF)_ESR
2R5TPD680M5(2.5V-680µF)_Imp.
2R5TPD680M5(2.5V-680µF)_ESR
TQC series
Frequency(kHz)
ESR, Impedance(Ω)
10
100
1
0.1
0.01
0.001
0.1 1 10 100 1000 10000
B2size(25TQC5R6M) Imp.
B2size(25TQC5R6M) ESR
Csize(25TQC10M) Imp.
Csize(25TQC10M) ESR
D2size(25TQC15M) Imp.
D2size(25TQC15M) ESR
D3Lsize(25TQC33M) Imp.
D3Lsize(25TQC33M) ESR
2R5TPLF470M7 vs 2R5TPF470M7L
Frequency(kHz)
ESR, Impedance(Ω)
10
100
1
0.1
0.01
0.001
0.1 1 10 100 1000 10000
2R5TPLF470M7(2.5V/470µF)_Imp.
2R5TPLF470M7(2.5V/470µF)_ESR
2R5TPF470M7L(2.5V-470µF)_Imp.
2R5TPF470M7L(2.5V-470µF)_ESR
6TPU22M ; S11 size
Frequency(kHz)
ESR, Impedance(Ω)
10
100
1
0.1
0.01
0.001
0.1 1 10 100 1000 10000
SIZE:S11
W
2.0×1.25×1.1
HL
6TPU22M(6.3V/22µF)_Imp.
6TPU22M(6.3V/22µF)_ESR
2R5TPE330M9 vs 2R5TPL330M9
Frequency(kHz)
ESR, Impedance(Ω)
10
100
1
0.1
0.01
0.001
0.1 1 10 100 1000 10000
2R5TPE330M9(2.5V/330µF)_Imp.
2R5TPE330M9(2.5V/330µF)_ESR
2R5TPL330M9(2.5V/330µF)_Imp.
2R5TPL330M9(2.5V/330µF)_ESR
Frequency Characteristics
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Characteristics
Characteristics
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPBSeries Standard Products
TPB series are the standard products corresponding to the
diversification of the needs.
Feature
20
Items Condition Characteristics
Endurance
Temperature characteristics of
Impedance ratio
Damp heat (Steady state)
Surge
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
105°C,2000h,
rated voltage applied
100kHz/+20°C
60°C,90 to 95%RH,500h,
No voltage applied
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105 (°C)
47 to 1000 (µF)
M:+_20%
2.5 to 10.0 (V.DC)
≤ 8.0 or 10.0 or 15.0 (%)
≤ 0.1CV (µA)
Please see the attached characteristics list
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+50%,–20% of the initial value
(
2R5TPB1000M
)
Within+40%, –20% of the initial value
(
Except for the above model
)
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
L
W
SW1
H
S
RV
(SV)
µF
47
68
82
100
150
220
330
470
680
1000
4.0
(5.0)
6.3
(8.0)
8.0
(10.0)
10.0
(13.0)
2.5
(3.2)
C
D3,D3L
D3L
D4,D3L
D4
C
C,D3,D3L
D3L
D4,D3L
D4
C
C,D3,D3L
D3L
D3L,D4
D4
C
C
C
D3,D3L
D3L
D3L,D4
D4
Specifications
Dimensions Size List
Size
code
C
D3L
D3
D4
W
(±0.2)
3.2
4.3
4.3
4.3
H
(±0.2)
2.8
2.8
3.1
3.8
S
(±0.2)
1.3
1.3
1.3
1.3
W1
(±0.1)
1.8
2.4
2.4
2.4
*1 ±0.3:D3L,D4
L*1
(±0.2)
6.0
7.3
7.3
7.3
(unit: mm)
T
P
B
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
21
Characteristics List
*1 100k to 500kHz,45°C
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
C
10TPB68MC
10TPB47MC
8TPB82MC
6TPB150MC
6TPB100MC
4TPB220MC
4TPB150MC
2R5TPB220MC
10.0
10.0
8.0
6.3
6.3
4.0
4.0
2.5
10.0
10.0
10.0
6.3
6.3
6.3
4.0
4.0
4.0
2.5
2.5
2.5
10.0
6.3
4.0
2.5
10.0
10.0
6.3
6.3
4.0
4.0
2.5
2.5
68
47
82
150
100
220
150
220
220
150
100
330
220
150
470
330
220
680
470
330
100
150
220
330
330
220
470
330
680
470
1000
680
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
10.0
10.0
8.0
10.0
10.0
8.0
10.0
10.0
8.0
10.0
10.0
8.0
8.0
8.0
8.0
8.0
10.0
10.0
15.0
10.0
15.0
10.0
15.0
10.0
68.0
47.0
65.6
94.5
63.0
88.0
60.0
55.0
220.0
150.0
100.0
207.9
138.6
94.5
188.0
132.0
88.0
170.0
117.5
82.5
100.0
94.5
88.0
82.5
330.0
220.0
296.1
207.9
272.0
188.0
250.0
170.0
55
55
45
45
45
45
45
45
40
40
55
40
40
55
40
40
55
40
40
55
55
55
65
65
35
40
35
40
35
40
30
40
1500
1500
1700
1700
1700
1700
1700
1700
2000
2000
1900
2000
2000
1900
2000
2000
1900
2000
2000
1900
32a
1900
1900
1500
1500
3000
3000
3000
3000
3000
3000
3000
3000
10TPB220ML
10TPB150ML
10TPB100ML
6TPB330ML
6TPB220ML
6TPB150ML
4TPB470ML
4TPB330ML
4TPB220ML
2R5TPB680ML
2R5TPB470ML
2R5TPB330ML
10TPB100M
6TPB150M
4TPB220M
2R5TPB330M
10TPB330M
10TPB220M
6TPB470M
6TPB330M
4TPB680M
4TPB470M
2R5TPB1000M
2R5TPB680M
D3L
D3
D4
Rated
Temperature
(°C)
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
Category
Voltage
(V)
10.0
10.0
8.0
6.3
6.3
4.0
4.0
2.5
10.0
10.0
10.0
6.3
6.3
6.3
4.0
4.0
4.0
2.5
2.5
2.5
10.0
6.3
4.0
2.5
10.0
10.0
6.3
6.3
4.0
4.0
2.5
2.5
Category
Temperature
(°C)
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
T
P
B
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPBSeries
B2 size is the miniaturized version of TPB series.
Feature
Standard Products (B2 Size)
22
Endurance
105°C,1000h,
rated voltage applied
*Rated temp. 85
°C
products:
85
°C
,1000h,rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
*6TPB100MA, 4TPB150MA, 2R5TPB220MA : 85°C
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
33 to 220
(
µF
)
M:±20%
2.5 to 10
(
V.DC
)
≤ 8.0
(
%
)
Please see the attached characteristic list
Please see the attached characteristic list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20
%
of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within
+
40
%
,
–20%
of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
RV
(SV)
µF
33
47
68
100
150
220
4.0
(5.0)
6.3
(8.0)
8.0
(10.0)
10.0
(13.0)
2.5
(3.2)
B2
B2
B2
B2
B2
B2
B2
B2
B2
B2
B2
B2
(unit: mm)
L
W
SW1
H
S
Size
code
B2
W
(±0.2)
2.8
H
(±0.1)
1.9
S
(±0.2)
0.8
W1
(±0.1)
2.2
L
(±0.2)
3.5
Dimensions Size List
T
P
B
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
23
Characteristics List
Size
code
SANYO
Part number
B2
10TPB47M
10TPB33M
8TPB47M
8TPB33M
6TPB100MA
6TPB100MAV
6TPB68M
6TPB47M
4TPB150MA
4TPB100M
4TPB100MV
4TPB68M
2R5TPB220MA
2R5TPB100M
Rated
Voltage
(V)
10.0
10.0
8.0
8.0
6.3
6.3
6.3
6.3
4.0
4.0
4.0
4.0
2.5
2.5
Rated
Temperature
(
°C
)
105
105
105
105
85
85
105
105
85
105
105
105
85
105
Category
Voltage
(V)
10.0
10.0
8.0
8.0
5.0
5.0
6.3
6.3
3.2
4.0
4.0
4.0
2.0
2.5
Category
Temperature
(
°C
)
105
105
105
105
105
105
105
105
105
105
105
105
105
105
Rated
Capacitance
(µF)
47
33
47
33
100
100
68
47
150
100
100
68
220
100
D.F.
(%max.)
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
L.C.
(µA)
max./5min.
47.0
33.0
37.6
26.4
63.0
63.0
42.8
29.6
60.0
40.0
40.0
27.2
55.0
25.0
E.S.R.
(mΩmax.)
100kHz/20°C
70
70
70
70
55
45
70
70
70
70
45
70
55
70
Maximum allowable
ripple current
(mArms)
100kHz*1
1100
1100
1100
1100
1200
1400
1100
1100
1100
1100
1300
1100
1200
1100
3
Reflow
Temp.
≤260°C
3
MSL
Reflow
Temp.
≤250°C
*1 100k to 500kHz,45°C
T
P
B
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPCSeries
TPC series has low profile and low ESR. TPC series aids in
the miniaturization of any products.
Feature
Low Profile Products
24
–55°C
+105°C
Endurance
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
33 to 330
(
µF
)
M:+_20%
2.5 to 10
(
V.DC
)
≤ 10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20
%
of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within
+
40
%
,
–20%
of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
*6TPC330M:85°C
105°C,2000h,rated voltage applied
C1 size:1000h
*Rated temp. 85
°C
products:
85
°C
, 2000h, rated voltage applied
Specifications
Dimensions Size List
RV
(SV)
µF
33
56
68
82
100
150
220
330
4.0
(5.0)
6.3
(8.0)
8.0
(10.0)
10.0
(13.0)
2.5
(3.2)
C1
D2
D2
C1
C1
D2
D2
C1
D2,C1
D2
D2
C1
D2
D2
D2
Size
code
C1
D2
W
(±0.2)
3.2
4.3
H
(±0.1)
1.4
1.9
S
(±0.2)
1.3
1.3
W1
(±0.1)
1.8
2.4
L
(±0.2)
6.0
7.3
(unit: mm)
SW1
H
L
W
S
T
P
C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
25
Characteristics List
Size
code
SANYO
Part number
D2
C1
10TPC100M
10TPC68M
8TPC150M
6TPC330MA
6TPC150M
6TPC100M
4TPC220M
4TPC150M
2R5TPC330M
2R5TPC220M
8TPC33M
6TPC100MC
6TPC68M
4TPC100M
4TPC56M
2R5TPC82M
Rated
Voltage
(V)
10.0
10.0
8.0
6.3
6.3
6.3
4.0
4.0
2.5
2.5
8.0
6.3
6.3
4.0
4.0
2.5
Rated
Temperature
(°C)
105
105
105
85
105
105
105
105
105
105
105
85
105
105
105
105
Category
Voltage
(V)
10.0
10.0
8.0
5.0
6.3
6.3
4.0
4.0
2.5
2.5
8.0
5.0
6.3
4.0
4.0
2.5
Category
Temperature
(°C)
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
Rated
Capacitance
(µF)
100
68
150
330
150
100
220
150
330
220
33
100
68
100
56
82
D.F.
(%max.)
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
L.C.
(µA)
max./5min.
100.0
68.0
120.0
207.9
94.5
63.0
88.0
60.0
82.5
55.0
26.4
63.0
42.8
40.0
22.4
20.5
E.S.R.
(mΩmax.)
100kHz/20°C
45
45
40
40
40
45
40
45
40
45
70
55
55
55
70
70
Maximum allowable
ripple current
(mArms)
100kHz*1
1700
1700
1900
1900
1900
1700
1900
1700
1900
1700
1200
1300
1300
1300
1200
1200
3
3
Reflow
Temp.
≤260°C
2a
3
MSL
Reflow
Temp.
≤250°C
*1 100k to 500kHz,45°C
T
P
C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPCSeries
B1 size is miniaturized, low profile version of TPC series.
Feature
B1 Size
26
Endurance
85°C,1000h,
rated voltage applied or
105°C,1000h,
category voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
85°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
10 to 56
(
µF
)
M:+_20%
2.5 to 12.5
(
V.DC
)
≤ 10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
Dimensions
Size List
SW1
H
L
W
S
Size
code
SANYO
Part number
B1
12TPC15M
12TPC10M
10TPC33MB
8TPC22M
6TPC47MB
6TPC33M
4TPC47M
2R5TPC56M
Rated
Voltage
(V)
12.5
12.5
10.0
8.0
6.3
6.3
4.0
2.5
Rated
Temperature
(
°C
)
85
85
85
85
85
85
85
85
Category
Voltage
(V)
10.0
10.0
8.0
6.3
5.0
5.0
3.2
2.0
Category
Temperature
(
°C
)
105
105
105
105
105
105
105
105
Rated
Capacitance
(µF)
15
10
33
22
47
33
47
56
D.F.
(%max.)
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
L.C.
(µA)
max./5min.
18.8
12.5
33.0
17.6
29.6
20.8
18.8
14.0
E.S.R.
(mΩmax.)
100kHz/20°C
80
80
70
70
70
70
70
70
Maximum allowable
ripple current
(mArms)
100kHz*1
800
800
1000
1000
1000
1000
1000
1000
3
Reflow
Temp.
≤260°C
3
MSL
Reflow
Temp.
≤250°C
*1 100k to 500kHz,45°C
RV
(SV)
µF
10
15
22
33
47
56
2.5
(3.2)
B1
4.0
(5.0)
B1
6.3
(8.0)
B1
B1
8.0
(10.0)
B1
10.0
(13.0)
B1
12.5
(16.0)
B1
B1
Characteristics List
Size
code
L
(±0.2)
B1 3.5
W
(±0.2)
2.8
H
(±0.1)
1.1
S
(±0.2)
0.8
W1
(±0.1)
2.2
(unit: mm)
T
P
C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPDSeries
TPD series has low ESR and high capacitance.
It is the most suitable for the high frequency and high cur-
rent switching power supply applications.
Feature
Low ESR . High Capacitance Products
27
Size
code
SANYO
Part number
D4D
6TPD470M
4TPD680M
2R5TPD1000M
2R5TPD1000M8
2R5TPD1000M6
2R5TPD1000M5
2R5TPD680M6
2R5TPD680M5
2R5TPD470M6
2R5TPD470M5
Rated
Voltage
(V)
6.3
4.0
2.5
2.5
2.5
Rated
Temperature
(
°C
)
105
105
105
105
105
Category
Voltage
(V)
6.3
4.0
2.5
2.5
2.5
Category
Temperature
(
°C
)
105
105
105
105
105
Rated
Capacitance
(µF)
470
680
1000
680
470
D.F.
(%max.)
10.0
10.0
10.0
10.0
10.0
L.C.
(µA)
max./5min.
296.1
272.0
250.0
170.0
117.5
E.S.R.
(mΩmax.)
100kHz/20°C
10
10
10
8
6
5
6
5
6
5
Maximum allowable
ripple current
(mArms)
100kHz*1
4400
4400
4400
4900
5600
6100
5600
6100
5600
6100
3
Reflow
Temp.
≤260°C
2a
MSL
Reflow
Temp.
≤250°C
SW1
H
L
W
S
Endurance 105°C,2000h,
rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
470 to 1000
(
µF
)
M:+_20%
2.5 to 6.3
(
V.DC
)
≤ 10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
Dimensions Size
code
L
(±0.3)
D4D 7.3
W
(±0.2)
4.3
H
(±0.2)
3.6
S
(±0.2)
1.3
W1
(±0.1)
2.4
(unit: mm)
T
P
D
*1 100k to 500kHz,45°C
Characteristics List
RV
(SV)
µF
470
680
1000
2.5
(3.2)
D4D
D4D
D4D
4.0
(5.0)
D4D
6.3
(8.0)
D4D
Size List
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPESeries
TPE series has low ESR and can aid in the miniaturization
of many products.
Feature
Low ESR Products (D2E, D3L, D4 Size)
28
Endurance
105°C,2000h,
rated voltage applied
*Rated temp. 85
°C
products:
85
°C
, 1000h, rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 cycles,
1kΩ discharge resistance,
surge voltage applied
*6TPE330MAP,16TPE220MAP:85°C
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
68 to 1500
(
µF
)
M:+_20%
2.5 to 10
(
V.DC
)
≤ 10.0
(
%
) *
D4size:≤ 15.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value (Except for the above model)
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Within+50%, –20% of the initial value (2R5TPE470M (I,F,C,9,7), 2R5TPE330M (I,F,C,9,7),
2R5TPE220M (I,F,C,9,7) ,2R5TPE1000M (I,F) ,2R5TPE1500M (F,C)
Specifications
Size
code
D2E
D3L
D4
W
(±0.2)
4.3
4.3
4.3
H*1
(±0.2)
1.8
2.8
3.8
S
(±0.2)
1.3
1.3
1.3
W1
(±0.1)
2.4
2.4
2.4
*1 ±0.1:D2E
L
(±0.3)
7.3
7.3
7.3
RV
(SV)
µF
68
100
150
220
330
470
680
1000
2.5
(3.2)
D2E
D2E
D2E
D3L
D4
4.0
(5.0)
D2E
D2E
D2E
D3L
D4
6.3
(8.0)
D2E
D2E
D2E
D2E,D3L
D4
D4
10.0
(13.0)
D2E
D3L
D4
(unit: mm)
L
W
SW1
H
S
Dimensions Size List
T
P
E
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
29
Characteristics List
Size
code
SANYO
Part number
Rated
Voltage
(V)
Category
Voltage
(V)
D2E
D3L
D4
10.0
6.3
6.3
6.3
6.3
6.3
4.0
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
10.0
6.3
4.0
2.5
10.0
6.3
6.3
4.0
2.5
2.5
10.0
5.0
5.0
6.3
6.3
6.3
4.0
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
10.0
6.3
4.0
2.5
10.0
6.3
6.3
4.0
2.5
2.5
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
15.0
15.0
15.0
15.0
15.0
68.0
207.9
138.6
138.6
94.5
63.0
132.0
88.0
60.0
117.5
235.0
82.5
165.0
55.0
110.0
220.0
207.9
188.0
170.0
330.0
428.4
296.1
272.0
250.0
375.0
105
85
85
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
68
330
220
220
150
100
330
220
150
470
470
330
330
220
220
220
330
470
680
330
680
470
680
1000
1500
3
2a
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
T
P
E
Rated
Temperature
(°C)
Category
Temperature
(°C)
E.S.R.
(mΩmax.)
100kHz/20°C
25
25
25
25
18
25
18
25
18
25
18
25
18
15
25
18
25
18
15
12
9
7
25
18
15
12
9
7
25
18
15
12
9
7
25
25
18
25
18
15
12
25
18
15
12
25
25
18
25
18
25
18
15
25
18
15
15
12
Maximum allowable
ripple current
(mArms)
100kHz*1
Rated
Capacitance
(µF)
*1 100k to 500kHz,45°C *2 Under evaluation
D.F.
(%max.)
L.C.
(µA)
max./5min.
10TPE68M
6TPE330MAP
6TPE220MAP
6TPE220M
6TPE220MI
6TPE150M
6TPE150MI
6TPE100M
6TPE100MI
4TPE330M
4TPE330MI
4TPE220M
4TPE220MI
4TPE220MF
4TPE150M
4TPE150MI
2R5TPE470M
2R5TPE470MI
2R5TPE470MF
2R5TPE470MC
2R5TPE470M9
2R5TPE470M7
2R5TPE330M
2R5TPE330MI
2R5TPE330MF
2R5TPE330MC
2R5TPE330M9
2R5TPE330M7
2R5TPE220M
2R5TPE220MI
2R5TPE220MF
2R5TPE220MC
2R5TPE220M9
2R5TPE220M7
10TPE220ML
6TPE330ML
6TPE330MIL
4TPE470ML
4TPE470MIL
4TPE470MFL
4TPE470MCL
2R5TPE680ML
2R5TPE680MIL
2R5TPE680MFL
2R5TPE680MCL
10TPE330M
6TPE680M
6TPE680MI
6TPE470M
6TPE470MI
4TPE680M
4TPE680MI
4TPE680MF
2R5TPE1000M
2R5TPE1000MI
2R5TPE1000MF
2R5TPE1500MF
2R5TPE1500MC
2400
2400
2400
2400
2800
2400
2800
2400
2800
2400
2800
2400
2800
3100
2400
2800
2400
2800
3100
3500
3900
4400
2400
2800
3100
3500
3900
4400
2400
2800
3100
3500
3900
4400
2400
2400
2800
2400
2800
3100
3500
2400
2800
3100
3500
3000
3000
3500
3000
3500
3000
3500
3900
3000
3500
3900
3900
4400
(*2)
3
(*2)
3
(*2)
3
(*2)
Size List
RV
(SV)
µF
47
100
120
150
220
330
2.0
(2.6)
2.5
(3.2)
B2
B2
B2
B2,C2,C3
4.0
(5.0)
B2
B2
B2,C2,C3
6.3
(8.0)
B2
B2
B2,C2,C3
C3
8.0
(10.0)
10.0
(13.0)
C2
B2
C3
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPESeries
This products is the miniaturized version of TPE series.
Feature
Low ESR Products (C3,C2,B2 Size)
30
Endurance
105°C,2000h,(B2size:1000h)
rated voltage applied
*
Rated temp. 85
°C
products:
85
°C
,1000h,rated voltage appiled
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 times,1kΩdischarge
resistance,surge voltage applied
*Rated temp 85°C products:
85°C,1000 times
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
47 to 330
(
µF
)
M:+_20%
2.5 to 10.0
(
V.DC
)
≤ 8.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value (Except for the above model)
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Within+50%, –20% of the initial value (2R5TPE220MAZB,2R5TPE330MAZB,
2TPE330MIB (MAFB,MAFGB),2R5TPE220MAPB,2R5TPE330MFC2 (CC2,9C2))
Specifications
Dimensions
Size
code
B2
C2
C3
W
(±0.2)
2.8
3.2
3.2
H*1
(±0.1)
1.9
1.8
2.5
S
(±0.2)
0.8
1.3
1.3
W1
(±0.1)
2.2
1.8
1.8
*1 ±0.2:C3
L
(±0.2)
3.5
6.0
6.0
(unit: mm)
H
W1
S S
L
W
T
P
E
Characteristics List
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
31
T
P
E
*1 100k to 500kHz,45°C *2 Under development *3 Under evaluation
3
3
3
(*3)
MSL
10TPE47MAZB
6TPE150MAZB
6TPE120MAZB
6TPE100MZB
*2
6PTE100MPB
*2
6TPE100MAZB
6PTE100MAPB*2
4TPE220MAZB
4TPE150MAZB
4TPE150MAUB
4TPE100MZB
2R5TPE330MAZB
2R5TPE220MZB
2R5TPE220MPB
2R5TPE220MLB
2R5TPE220MIB
2R5TPE220MFGB
2R5TPE220MAFB*2
2R5TPE220MAZB
2R5TPE220MAPB
2R5TPE150MZB
2TPE330MIB
2TPE330MAFGB
2TPE330MAFB*2
8TPE100MPC2
6TPE150MPC2
6TPE150MIC2
4TPE220MIC2
4TPE220MFC2
2R5TPE330MFC2
2R5TPE330MCC2
2R5TPE330M9C2
10TPE150MGC
6TPE220MPC
6TPE150MPC
4TPE220MPC
4TPE220MIC
2R5TPE330MPC
2R5TPE330MIC
2R5TPE330MFC
Size
code
SANYO
Part number
Rated
Voltage
(V)
Category
Voltage
(V)
Rated
Temperature
(°C)
Category
Temperature
(°C)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Reflow
Temp.
≤260°C
Reflow
Temp.
≤250°C
10.0
6.3
6.3
6.3
6.3
6.3
4.0
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.0
2.0
8.0
6.3
4.0
2.5
10.0
6.3
6.3
4.0
2.5
8.0
5.0
5.0
6.3
5.0
5.0
3.2
3.2
4.0
2.0
2.5
2.5
2.0
2.0
2.5
2.0
1.6
8.0
6.3
4.0
2.5
10.0
6.3
6.3
4.0
2.5
85
85
85
105
85
85
85
85
105
85
105
105
85
85
105
105
85
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
47
150
120
100
100
100
220
150
100
330
220
220
220
220
150
330
330
100
150
220
330
150
220
150
220
330
47.0
94.5
75.6
63.0
63.0
63.0
88.0
60.0
40.0
82.5
55.0
110.0
110.0
55.0
37.5
132.0
132.0
80.0
94.5
88.0
82.5
150.0
138.6
94.5
88.0
82.5
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
10.0
8.0
8.0
8.0
8.0
35
35
35
35
25
35
25
35
35
30
35
35
35
25
21
18
15/300k
15
35
25
35
18
15/300k
15
25
25
18
18
15
15
12
9
55
25
25
25
18
25
18
15
1400
1400
1400
1400
1600
1400
1600
1400
1400
1500
1400
1400
1400
1600
1700
1800
1800
2000
1400
1600
1400
1800
1800
2000
2200
2200
2600
2600
2900
2900
3300
3700
1500
2400
2400
2400
2800
2400
2800
3100
B2
C2
C3
MSL
Characteristics List
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPFSeries
TPF series has low ESR and high capacitance at standard
form.
Feature
Low ESR . High Capacitance Products
32
Endurance 105°C,2000h,
rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
150 to 680
(
µF
)
M:+_20%
2.0
to 10.0
(
V.DC
)
10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+50%, –20% of the initial value (D2E size)
Within+40%, –20% of the initial value (Except for the above model )
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
Dimensions
Size List
L
W
SW1
H
S
Size
code
D3L
D2E
W
(±0.2)
4.3
4.3
H*1
(±0.1)
2.8
1.8
S
(±0.1)
1.3
1.3
W1
(±0.1)
2.4
2.4
L
(±0.3)
7.3
7.3
(unit: mm)
T
P
F
*1 ±0.1:D2E
RV
(SV)
µF
150
220
330
470
680
2.5
(3.2)
D3L
D3L
D3L
4.0
(5.0)
D3L
D3L
2.0
(2.6)
D2E
D2E
D2E
6.3
(8.0)
D3L
D3L
10.0
(13.0)
D3L
*1 100k to 500kHz,45°C *2 Under evaluation
Size
code
SANYO
Part number
Rated
Voltage
(V)
Category
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
D3L
D2E
10TPF150ML
6TPF330M9L
6TPF220ML
4TPF470ML
4TPF330ML
2R5TPF680ML
2R5TPF680M7L
2R5TPF680M6L
2R5TPF470ML
2R5TPF470M7L
2R5TPF330M7L
2TPF470M6
2TPF330M6
2TPF220M6
10.0
6.3
6.3
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.0
2.0
2.0
10.0
6.3
6.3
4.0
4.0
2.5
2.5
2.5
2.5
2.5
2.5
2.0
2.0
2.0
150
330
220
470
330
680
680
680
470
470
330
470
330
220
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
150.0
207.9
138.6
188.0
132.0
170.0
170.0
170.0
117.5
117.5
82.5
188.0
132.0
188.0
15
9
12
10
12
10
7
6
10
7
7
6
6
6
3600
3900
4000
4400
4000
4400
4400
4400
4400
4400
4400
4400
4400
4400
3
2a
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
Rated
Temperature
(°C)
Category
Temperature
(°C)
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
(*2)
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
33
TPG
Series
TPG series is high capacitance model of the small size . low
profile product. Suitable for the miniaturization design of the
electronics device.
Feature
Small Size . High Capacitance Products
T
P
G
Endurance
85°C,1000h,
rated voltage applied or
105°C,1000h,
category voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
85°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
30 to 220
(
µF
)
M:+_20%
2.5 to 12.5
(
V.DC
)
≤ 10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
Dimensions
SW1
H
L
W
S
Size
code
L
(+0.3/–0.1)
B1G
B15G
3.5
3.5
W
(+0.3/–0.1)
2.8
2.8
H
(±0.1)
1.1
1.4
S
(±0.2)
0.8
0.8
W1
(±0.1)
2.2
2.2
(unit: mm)
Characteristics List
*1 100k to 500kHz,45°C
Size
code
SANYO
Part number
Rated
Voltage
(V)
Category
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
B15G
B1G
6TPG150M
4TPG220M
12TPG33M
10TPG47M
10TPG33M
8TPG47M
6TPG100M
6TPG68M
4TPG150M
2R5TPG220M
6.3
4.0
12.5
10.0
10.0
8.0
6.3
6.3
4.0
2.5
5.0
3.2
10.0
8.0
8.0
6.4
5.0
5.0
3.2
2.0
150
220
33
47
33
47
100
68
150
220
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
94.5
88.0
41.3
47.0
33.0
37.6
63.0
42.8
60.0
55.0
70
70
70
70
70
70
70
70
70
70
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
33
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
Rated
Temperature
(°C)
Category
Temperature
(°C)
85
85
85
85
85
85
85
85
85
85
105
105
105
105
105
105
105
105
105
105
Size List
RV
(SV)
µF
33
47
68
100
150
220
4.0
(5.0)
B1G
B15G
6.3
(8.0)
B1G
B1G
B15G
2.5
(3.2)
B1G
8.0
(10.0)
B1G
10.0
(13.0)
12.5
(16.0)
B1G
B1G
B1G
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
TPL/TPLFSeries
TPL series has a low ESL and low ESR advantage using an
unique face down terminal structure.
Feature
Low ESR . Low ESL Products Face Down Terminal Type
34
Endurance 105°C,2000h,
rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 times,
1kΩ discharge resistance,
Surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
220 to 470
(
µF
)
M:+_20%
2.0 to 2.5
(
V.DC
)
≤ 10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+50%, –20% of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
Dimensions Size List
RV
(SV)
µF
220
330
470
2.0
(2.6)
2.5
(3.2)
D2T
D2T
D2T
D2T
D2T
D2T
W
L
(+)
(–)
H
W1
S4
S3
S1 S2
Size
code
D2T
L
(±0.3)
7.3
W
(±0.2)
4.3
H
(±0.1)
1.8
S1/S2
(±0.2)
1.1
S3
(±0.1)
1.1
S4
(±0.2)
2.3
W1
(±0.1)
2.8
(unit: mm)
T
P
L
/
T
P
L
F
(back)
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
35
T
P
L
/
T
P
L
F
117.5
235.0
82.5
165.0
55.0
Characteristics List
(TPL)
(TPLF)
*1 100k to 500kHz,45°C *2 Under development
2R5TPL470MC
2R5TPL470M9
2R5TPL470M8
2R5TPL470M7
*2
2R5TPL330MC
2R5TPL330M9
2R5TPL330M8
2R5TPL330M7
*2
2R5TPL220MC
2.5
2.5
2.5
2.5
2.5
2.5
12
9
8
7
12
9
8
7
12
3400
3900
4100
4400
3400
3900
4100
4400
3400
32a
D2T
105
105
105
105
105
105
470
330
220
10.0
10.0
10.0
*1 100k to 500kHz,45°C
2TPLF470M7
2TPLF470M6
2TPLF330M7
2TPLF330M6
2TPLF220M7
2TPLF220M6
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
7
6
7
6
7
6
4400
4700
4400
4700
4400
4700
32a
D2T
105
105
105
105
105
105
105
105
105
105
105
105
470
470
330
330
220
220
10.0
10.0
10.0
10.0
10.0
10.0
188.0
188.0
132.0
132.0
88.0
88.0
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Rated
Temperature
(°C)
Category
Voltage
(V)
Category
Temperature
(°C)
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Rated
Temperature
(°C)
Category
Voltage
(V)
Category
Temperature
(°C)
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
36
Endurance 85°C,1000h,
rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
85°C,1000 times,
1kΩ discharge resistance,
Surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+85°C
Z/Z20°C
Z/Z20°C
–55 to +85
(
°C
)
10 to 100
(
µF
)
M:+_20%
2.5 to 10.0
(
V.DC
)
≤ 10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20
%
of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within
+
40
%
,
–20%
of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Specifications
T
P
U
Dimensions
SW1
L
W
H
S
Size
code
W
(±0.1)*1H
(±0.1)
S
(±0.1)*1W1
(±0.1)
L
(±0.1)*1
S08
S11
A09
B09
2.0
2.0
3.2
3.5
1.25
1.25
1.6
2.8
0.8
1.1
0.9
0.9
0.5
0.5
0.8
0.8
0.9
0.9
1.2
2.2
(unit: mm)
*1 ±0.2:A09,B09
TPUSeries
TPU series has a real advantage in size-sensitive applica-
tions using a face down terminal structure.
Feature
Small Size . Low Profile Products Face Down Terminal Type
Size List
RV
(SV)
µF
10
15
22
33
47
68
100
2.5
(3.2)
S08
S11
A09
3.15
(4.0)
A09
4.0
(5.0)
S08
S11
A09,B09
6.3
(8.0)
S08
S11
A09,B09
8.0
(10.0)
B09
10.0
(13.0)
A09
Characteristics List
*1 100k to 500kHz,45°C
6TPU10M
4TPU15M
2R5TPU22M
6TPU22MSK
4TPU33MSK
2R5TPU47MSK
10TPU33MAI
6TPU47MAI
4TPU68MAI
3TPU100MAI
2R5TPU100MAI
8TPU33MBI
6TPU47MBI
4TPU68MBI
6.3
4.0
2.5
6.3
4.0
2.5
10.0
6.3
4.0
3.15
2.5
8.0
6.3
4.0
6.3
4.0
2.5
6.3
4.0
2.5
10.0
6.3
4.0
3.15
2.5
8.0
6.3
4.0
250
250
250
150
150
150
150
150
150
150
150
70
70
70
400
400
400
510
510
510
510
510
510
510
510
800
800
800
3
Under
evaluation
3
S08
S11
A09
B09
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
10
15
22
22
33
47
33
47
68
100
100
33
47
68
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
6.3
6.0
5.5
13.9
13.2
11.8
33.0
29.6
27.2
31.5
25.0
26.4
29.6
27.2
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Rated
Temperature
(°C)
Category
Voltage
(V)
Category
Temperature
(°C)
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
Size List
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
37
T
A
TASeries
TA series are high reliability products that the heat
resistance and moisture resistance are improved.
*Suitable for the industrial equipment or car electronics (e.g. Car navigation system).
Feature
High Reliability Products (For The Car Electronics)
Endurance 105°C,2000h,
rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Load) 85°C, 85%RH, 500h,
rated voltage applied
60°C,90 to 95%RH,500h,
No voltage applied
Damp heat (Steady state)
Surge
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
47 to 680
(
µF
)
M:+_20%
2.5
to 10
(
V.DC
)
10.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value
*
1
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value
*
1
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
*
1 Within +50%, –20% of the initial value(2R5TAE470M(F,C), 2R5TAE330M(F,C), 2R5TAE220M(F,C))
Specifications
L
W
SW1
H
S
Dimensions Size
code
L*2
(±0.3)
B2
D2E
D3L
3.5
7.3
7.3
W
(±0.2)
2.8
4.3
4.3
H*1
(±0.2)
1.9
1.8
2.8
S
(±0.2)
0.8
1.3
1.3
W1
(±0.1)
2.2
2.4
2.4
(unit: mm)
RV
(SV)
µF
47
68
100
150
220
330
470
680
2.5
D2E
D2E
D2E
D3L
4
B2
D2E
D3L
6.3
B2
B2
D2E
D2E
D3L
10
B2
D2E
D3L
*1 ±0.1:D2E,B2 *2 ±0.2:B2
Characteristics List
*1 100k to 500kHz,45°C
10.0
6.3
6.3
4.0
10.0
6.3
6.3
4.0
2.5
2.5
2.5
10.0
6.3
4.0
2.5
33
B2
D2E
D3L
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
47
68
47
100
68
220
150
220
470
330
220
220
330
470
680
8.0
8.0
8.0
8.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
47.0
42.8
29.6
40.0
68
138.6
94.5
88
117.5
82.5
55
220.0
207.9
188
170
70
70
70
70
25
25
18
25
25
18
25
15
12
25
18
15
12
25
15
25
25
25
18
25
15
1100
1100
1100
1100
2400
2400
2800
2400
2400
2800
2400
3100
3500
2400
2800
3100
3500
2400
3100
2400
2400
2400
2800
2400
3100
10.0
6.3
6.3
4.0
10.0
6.3
6.3
4.0
2.5
2.5
2.5
10.0
6.3
4.0
2.5
10TAB47M
6TAB68M
6TAB47M
4TAB100M
10TAE68M
6TAE220M
6TAE220MI
6TAE150M
4TAE220M
4TAE220MI
2R5TAE470M
2R5TAE470MF
2R5TAE470MC
2R5TAE330M
2R5TAE330MI
2R5TAE330MF
2R5TAE330MC
2R5TAE220M
2R5TAE220MF
10TAE220ML
6TAE330ML
4TAE470ML
4TAE470MIL
2R5TAE680ML
2R5TAE680MFL
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Rated
Temperature
(°C)
Category
Voltage
(V)
Category
Temperature
(°C)
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
38
THSeries
TH series has 125°C capability guaranteed. It is the most
suitable for the high reliability industrial equipment.
Feature
125°C Guaranteed Products (THB/THC/THD/THE series)
Endurance 125°C,1000h,
category voltage applied
Temperature characteristics of
Impedance ratio 100kHz/20°C
Damp heat (Steady state) 60°C,90 to 95%RH,500h,
No voltage applied
Surge
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
tan
L.C.
∆C/C
tan
L.C.
∆C/C
tan
L.C.
–55°C
+125°C
Z/Z20°C
Z/Z20°C
–55 to +125
(
°C
)
CharacteristicsConditionItems
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 2 times the initial limit
≤ 2 times the initial limit
Within+50%, –20% of the initial value (2R5THB1000M)
Within+40%, –20% of the initial value (Except for the above model)
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Series
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
THB THC THD THE
M:+_20%
Please see the attached characteristic list
Please see the attached characteristic list
100 to 1000
(
µF
)
68 to 220
(
µF
)
330 to 680
(
µF
)
150 to 330
(
µF
)
2.5 to 10
(
V.DC
)
≤ 8.0 or 10.0 or 15.0
(
%
)
2.5 to 10
(
V.DC
)
≤ 10.0
(
%
)
2.5 to 6.3
(
V.DC
)
≤ 10.0
(
%
)
2.5 to 6.3
(
V.DC
)
≤ 10.0
(
%
)
Specifications
Dimensions Size List
Size
code
D2E
D2
D3L
D4
D4D
W
(±0.2)
4.3
4.3
4.3
4.3
4.3
H*2
(±0.1)
1.8
1.9
2.8
3.8
3.6
S
(±0.2)
1.3
1.3
1.3
1.3
1.3
W1
(±0.1)
2.4
2.4
2.4
2.4
2.4
*1 ±0.2:D2 *2 ±0.2:D3L,D4,D4D
L*1
(±0.3)
7.3
7.3
7.3
7.3
7.3
(unit: mm)
W1
H
SS
L
W
µF
RV
(SV)
Series
2.5
(3.2)
D2
D3L
D2E
D3L
D4
D4D
D4
4.0
(5.0)
D2
D2E
D3L
D4D
D4
6.3
(8.0)
D2
D2E
D3L
D4
D4D
D4
10.0
(13.0)
D2
D3L
D4
D4
THC
THB
THC
THE
THB
THC
THE
THB
THD
THE
THB
THD
THB
THD
THB
68
100
150
220
330
470
680
1000
T
H
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
39
Characteristics List
THB
THC
THE
THD
D3L
D4
D2
D2E
D4
1900
2000
2000
2000
1900
3000
3000
3000
3000
3000
3000
3000
1700
1900
1900
1700
2400
2800
2400
2800
3100
2400
2800
3100
4400
4400
4400
Under
evaluation
5
10THB100ML
6THB220ML
4THB330ML
2R5THB470ML
2R5THB330ML
10THB330M
10THB220M
6THB470M
6THB330M
4THB680M
2R5THB1000M
2R5THB680M
10THC68M
6THC150M
4THC220M
2R5THC220M
6THE150M
6THE150MI
4THE220M
4THE220MI
4THE220MF
2R5THE330M
2R5THE330MI
2R5THE330MF
6THD330M
4THD470M
2R5THD680M
*1 100k to 500kHz,45°C
10.0
6.3
4.0
2.5
2.5
10.0
10.0
6.3
6.3
4.0
2.5
2.5
10.0
6.3
4.0
2.5
6.3 105 4.0 125150 10.0 94.5
4.0 105 2.5 125220 10.0 88.0
2.5
6.3
4.0
2.5
105
105
105
105
1.6
4.0
2.5
1.6
125
125
125
125
330
330
470
680
10.0
10.0
10.0
10.0
82.5
207.9
188.0
170.0
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
6.3
4.0
2.5
1.6
1.6
6.3
6.3
4.0
4.0
2.5
1.6
1.6
6.3
4.0
2.5
1.6
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
100
220
330
470
330
330
220
470
330
680
1000
680
68
150
220
220
8.0
10.0
10.0
10.0
10.0
10.0
10.0
15.0
10.0
15.0
15.0
10.0
10.0
10.0
10.0
10.0
100.0
138.6
132.0
117.5
82.5
330.0
220.0
296.1
207.9
272.0
250.0
170.0
68.0
94.5
88.0
55.0
55
40
40
40
55
35
40
35
40
35
30
40
45
40
40
45
25
18
25
18
15
25
18
15
10
10
10
T
H
Series
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Temperature
(°C)
Rated
Capacitance
(µF)
Category
Voltage
(V)
Category
Temperature
(°C)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
40
T
R
TR series are improved model of the moisture resistance
more than standard products.
Suitable for the industrial equipment.
Feature
TRSeries High Moisture Resistance Products
Endurance
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Load) 85°C, 85%RH, 500h,
rated voltage applied
60°C,90 to 95%RH,500h,
No voltage applied
Damp heat (Steady state)
Surge
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
33 to 680
(
µF
)
M:+_20%
2.5
to 10
(
V.DC
)
10.0
(
%
)
*
B2size:≤ 8.0 (%) D4size:≤ 15.0 (%)
Please see the attached characteristics list
Please see the attached characteristics list
1.0 to 2.0
0.6 to 1.0
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value (Except for the above model)
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value (Except for the above model)
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
CharacteristicsConditionItems
105°C,2000h,(B2size:1000h)
rated voltage applied
*
Rated temp. 85
°C
products:
85
°C
,1000h,rated voltage appiled
105°C,1000 times,1kΩdischarge
resistance,surge voltage applied
*Rated temp. 85°C products:85°C
Within+50%, –20% of the initial value (2R5TRE220MAZB, 2R5TRE470M (F,C),
2R5TRE330M (F,C), 2R5TRE220M (F,C))
Within+50%, –20% of the initial value (2R5TRE220MAZB, 2R5TRE470M (F,C),
2R5TRE330M (F,C), 2R5TRE220M (F,C))
Specifications
L
W
SW1
H
S
Dimensions
Size
code
B2
D2E
D3L
W
(±0.2)
2.8
4.3
4.3
H*2
(±0.2)
1.9
1.8
2.8
S
(±0.2)
0.8
1.3
1.3
W1
(±0.1)
2.2
2.4
2.4
*1 ±0.2:B2 *2 ±0.1:D2E,B2
L*1
(±0.3)
3.5
7.3
7.3
(unit: mm)
RV
(SV)
µF
33
47
68
100
150
220
330
470
680
2.5
B2,D2E
D2E
D2E
D3L
4
B2
B2
D2E
D3L
D3L
6.3
B2
B2
B15G,D2E
D2E
D3L
10
B2
D2E
Size List
Characteristics List
41
T
R
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
*1 100k to 500kHz,45°C
B2
B15G
D2E
D3L
6.3
10.0
6.3
6.3
4.0
4.0
2.5
10.0
6.3
6.3
4.0
2.5
2.5
2.5
6.3
4.0
4.0
2.5
5.0
10.0
5.0
6.3
3.2
4.0
2.0
10.0
6.3
6.3
4.0
2.5
2.5
2.5
6.3
4.0
4.0
2.5
70
70
35
70
35
70
35
25
25
18
25
25
18
25
15
12
25
15
12
25
15
12
25
25
18
25
25
15
1000
1100
1400
1100
1400
1100
1400
2400
2400
2800
2400
2400
2800
2400
3100
3500
2400
3100
3500
2400
3100
3500
2400
2400
2800
2400
2400
3100
3
2a
3
85
105
85
105
85
105
85
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
150
33
100
47
150
68
220
68
220
150
220
470
330
220
330
470
330
680
10.0
8.0
8.0
8.0
8.0
8.0
8.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
94.5
33.0
63.0
29.6
60.0
27.2
55.0
68
138.6
94.5
88
117.5
82.5
55
207.9
188
132
170
6TRG150M
10TRB33M
6TRE100MAZB
6TRB47M
4TRE150MAZB
4TRB68M
2R5TRE220MAZB
10TRE68M
6TRE220M
6TRE220MI
6TRE150M
4TRE220M
4TRE220MI
2R5TRE470M
2R5TRE470MF
2R5TRE470MC
2R5TRE330M
2R5TRE330MF
2R5TRE330MC
2R5TRE220M
2R5TRE220MF
2R5TRE220MC
6TRE330ML
4TRE470ML
4TRE470MIL
4TRE330ML
2R5TRE680ML
2R5TRE680MFL
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Rated
Temperature
(°C)
Category
Voltage
(V)
Category
Temperature
(°C)
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
42
T
Q
C
1.0 to 2.0
0.6 to 1.0
Endurance
105
°C
,2000h
25TQC15M,25TQC22M (category voltage applied),
20TQC22M,16TQC33M,16TQC47M (rated voltage applied)
105
°C
,1000h
25TQC5R6M,25TQC33M,25TQC22MV,25TQC15MV,25TQC10M (category voltage applied),
20TQC8R2M,20TQC47M,16TQC10M,16TQC68M,20TQC15M,16TQC22M,
20TQC22MV,20TQC33MV,16TQC33MV,16TQC47MV (rated voltage applied)
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90to95%RH,500h,
No voltage applied
Surge
15to35°C,1000 times,
1kΩdischarge resistance,
surge voltage applied
∆C/C
tan
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
5.6 to 68
(
µF
)
M:+_20%
16 to 25
(
V.DC
)
≤ 10.0
(
%
)
≤ 0.1CV
*
B2size: ≤ 0.3CV
Please see the attached characteristics list
CharacteristicsConditionItems
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
(
µA
)
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Within+40%, –20% of the initial value
≤ 1.5 times the initial limit
≤ 3 times the initial limit
Within+_5% of the initial value
≤ The initial limit
≤ 3 times the initial limit
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
∆C/C
tan
L.C.
∆C/C
tan
L.C.
Specifications
Dimensions
Size List
TQCSeries High Voltage Products
TQC series is perfect for high voltage, low ESR and low profile applications. It is the
most suitable for pass-con of the motor driver by 12V, the input of the DCDC converter.
Peak temperature 250˚C lead free reflow soldering products. (See P17)
*Please contact us, if your reflow condition exceeds this condition.
Feature
L
SW1
W
H
S
Size
code
L*1
(±0.2)
B2
C
D2
D3L
3.5
6.0
7.3
7.3
W
(±0.2)
2.8
3.2
4.3
4.3
H*2
(±0.1)
1.9
2.8
1.9
2.8
S
(±0.2)
0.8
1.3
1.3
1.3
W1
(±0.1)
2.2
1.8
2.4
2.4
(unit: mm)
*1 ±0.3:D3L *2 ±0.2:C,D3L
RV
(SV)
µF
5.6
8.2
10
15
22
33
47
68
16
(20)
B2
C
D2
D2
D3L
20
(23)
B2
C
D2
D3L
25
(29)
B2
C
D2
D2
D3L
Under
evaluation
3
Characteristics List
B2
C
D2
D3L
25TQC5R6M
20TQC8R2M
16TQC10M
25TQC10M
20TQC15M
16TQC22M
25TQC22M
25TQC22MV
25TQC15M
25TQC15MV
20TQC22M
16TQC33M
16TQC47M
25TQC33M
20TQC47M
16TQC68M
25*4
20
16
25*4
20
16
25*4
25*4
25*4
25*4
20
16
16
25*4
20
16
85
105
105
85
105
105
85
85
85
85
105
105
105
85
105
105
20
-
-
20
-
-
20
20
20
20
-
-
-
20
-
-
105
-
-
105
-
-
105
105
105
105
-
-
-
105
-
-
5.6
8.2
10
10
15
22
22
22
15
15
22
33
47
33
47
68
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
42.0
49.2
48.0
25.0
30.0
35.2
44.0
55.0
38.0
38.0
44.0
52.8
75.2
82.5
94.0
108.8
100
100
100
95
80
80
90
45
90
45
80
70
70
60
55
50
800
800
800
900
1000
1000
1000
1500
1000
1500
1300
1400
1400
1400
1450
1500
*3 100k to 500kHz,105°C *4 Please reduce 0.25V per 1°C from over 85°C for 25V products
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Capacitance
(µF)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*3
Rated
Temperature
(°C)
Category
Voltage
(V)
Category
Temperature
(°C)
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
43
A
P
C
/
A
P
D
RoHS compliance
Solid Electrolytic Capacitors with Polymerized Organic Semiconductor
Dimensions
Size List
APC/APDSeries
AP series is and has a cost performance advantage and
low profile by using aluminum foil for the anode.
Feature
Aluminum Anode Products
Specifications
RV
(SV)
µF
10
15
22
33
4.0
(5.0)
D1
D2
6.3
(8.0)
D1,D2
D2
L
SW1
W
H
S
Endurance 105°C,2000h,
rated voltage applied
Temperature characteristics of
Impedance ratio 100kHz/+20°C
Damp heat (Steady state) 60°C,90to95%RH,500h,
No voltage applied
Surge
105°C,1000 cycles,
1kΩdischarge resistance,
surge voltage applied
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
∆C/C
D.F.
L.C.
–55°C
+105°C
Z/Z20°C
Z/Z20°C
–55 to +105
(
°C
)
10 to 33
(
µF
)
M:+_20%
4.0 to 6.3
(
V.DC
)
≤ 5.0 or 8.0
(
%
)
Please see the attached characteristics list
Please see the attached characteristics list
CharacteristicsConditionItems
0.9 to 2.0
0.6 to 1.1
Within+_20% of the initial value
≤ 1.5 times the initial limit
≤ The initial limit
Within+40%, –20% of the initial value
≤ 1.5 times the initial limit
≤ 5 times the initial limit
Within+_5% of the initial value
≤ twice the initial limit
≤ 3 times the initial limit
Operating Temperature range
Rated capacitance range
Capacitance tolerance
Rated voltage
Dissipation Factor (D.F.)
Leakage current
Equivalent series resistance (E.S.R. mΩmax.)
—
120Hz/20°C
120Hz/20°C
—
120Hz/20°C
Rated voltage applied, after 5 minutes
100kHz/20°C
Size
code
D1
D2
W
(±0.2)
4.3
4.3
H
(±0.1)
1.4
1.9
S
(±0.2)
1.3
1.3
W1
(±0.1)
2.4
2.4
L
(±0.2)
7.3
7.3
(unit: mm)
Characteristics List
*1 100k to 500kHz,45°C
6APD10M
4APD15M
6APC22M
6APC10M
4APC33M
6.3
4.0
6.3
6.3
4.0
6.3
4.0
6.3
6.3
4.0
70
70
40
70
40
1900
1900
1900
1900
1900
Under
evaluation
5
4
APD
APC
D1
D2
105
105
105
105
105
105
105
105
105
105
10
15
22
10
33
8.0
8.0
5.0
8.0
5.0
2.5
2.4
13.9
6.3
13.2
Series
Size
code
SANYO
Part number
Rated
Voltage
(V)
Rated
Temperature
(°C)
Rated
Capacitance
(µF)
Category
Voltage
(V)
Category
Temperature
(°C)
D.F.
(%max.)
L.C.
(µA)
max./5min.
E.S.R.
(mΩmax.)
100kHz/20°C
Maximum allowable
ripple current
(mArms)
100kHz*1
Reflow
Temp.
≤260°C
MSL
Reflow
Temp.
≤250°C
●Modifying the subjects and specifications in this catalogue without any notice.
SANYO Electric Co., Ltd.
Electronic Device Company
■Sales division(Japan)
1-1 SANYO-cho, Daito, Osaka, 574-8534
Phone: (072)870-6375/6377 FAX: (072)870-1174
■SANYO Component Europe GmbH
Stahlgruberring 4, 81829 Munich Germany
Phone: 49-(0)89-460095-284 FAX: 49-(0)89-460095-275
■Korea office
9th Floor, Han-Lim Building 146-7, Ssanglim-Dong, Chung-Gu Seoul, Korea
Phone: 82-2-2273-5861 FAX: 82-2-2273-6053
SANYO Electronic Device (U.S.A.)Corporation
■San Diego Headquarter
2055 SANYO Ave., San Diego, CA 92154, U.S.A.
Phone: 1-619-661-6835 FAX: 1-619-661-1055
■San Jose sales office
1230 Oakmead Parkway, Ste. #314, Sunnyvale, CA 94085, U.S.A.
Phone: 1-408-749-9714 FAX: 1-408-749-0212
■Dallas sales office
2600 Network Blvd. 6F. Frisco TX. 75034, U.S.A.
Phone: 1-469-362-5465 FAX: 1-469-362-5463
■Detroit sales office
27000 Meadowbrook Rd., Suite 210 Novi, MI 48377, U.S.A.
Phone:1-248-344-1245 FAX: 1-248-479-0428
■Hartford sales office
P.O.Box 76 Waterford. CT 06385, U.S.A.
Phone:1-860-447-9553 FAX1-860-447-9573
■Atlanta sales office
P.O. Box 70666, Marietta, GA 30007, U.S.A.
Phone:1-770-650-5654 FAX: 1-770-640-5081
http://www.sanyodevice.com
SANYO Electronic Components (Singapore)Pte., Ltd.
70 Anson Road #19-01 To 08, Apex Tower Singapore/079905/Singapore
Phone: 65-6223-0225 FAX: 65-6223-0986
http://www.edc.sanyo.com
http://www.sanyochina.com
SANYO Electronic Components (H.K.)Ltd.
■Hong Kong Headquarter
Suite 3601-06, 36/F, Tower 6, The Gateway, Harbour City, 9 Canton Road, T.S.T., Kowloon, Hong Kong.
Phone: 852-2366-2577 FAX: 852-2301-2255
■Shanghai office
Room2107, Ruijin Building, 205 Mao Min Rd.(S), Shanghai, China
Phone: 86-21-6415-6669 FAX: 86-21-6445-8543
■Shenzhen office
Room301, East Building, High-Tech Plaza, Phase 2, Tian An Cyberpark Futian, Shenzhen, Guangdong
China 518040
Phone: 86-755-8835-2319 FAX: 86-755-8835-2324
■Beijing office
Room708, China Life Tower No.16 Chaoyangmenwai Ave., Beijing, China
Phone: 86-10-8525-2600 FAX: 86-10-8525-2602
■Taiwan Branch(Taiwan)
10F., No.101, Sec.2, Nanjing E. Rd., Jhongshan District, Taipei City 104, Taiwan (R.O.C.)
Phone:886-2-2536-1855 FAX: 886-2-2536-6168
