2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
1
REV 1.1
08 / 2010
Feature
1.5V ± 0.075V / 1.35V -0.0675V/+0.1V (JEDEC
Standard Power Supply)
8 Internal memory banks (BA0- BA2)
Differential clock input (CK, )
Programmable  Latency: 6, 7, 8, 9, 10, 11
Programmable Additive Latency: 0, CL-1, CL-2
Programmable Sequential / Interleave Burst Type
Programmable Burst Length: 4, 8
8 bit prefetch architecture
Output Driver Impedance Control
Write Leveling
OCD Calibration
Dynamic ODT (Rtt_Nom & Rtt_WR)
Auto Self-Refresh
Self-Refresh Temperature
RoHS compliance and Halogen free
Packages:
78-Ball BGA for x4 & x8 components
96-Ball BGA for x16 components
Description
The 2Gb Double-Data-Rate-3 (DDR3) DRAMs is a high-speed CMOS Double Data Rate32 SDRAM containing
2,147,483,648 bits. It is internally configured as an octal-bank DRAM.
The 2Gb chip is organized as 64Mbit x 4 I/O x 8 bank, 32Mbit x 8 I/O x 8 bank or 16Mbit x 16 I/O x 8 bank device. These
synchronous devices achieve high speed double-data-rate transfer rates of up to 1600 Mb/sec/pin for general applications.
The chip is designed to comply with all key DDR3 DRAM key features and all of the control and address inputs are
synchronized with a pair of externally supplied differential clocks. Inputs are latched at the cross point of differential clocks
(CK rising and  falling). All I/Os are synchronized with a single ended DQS or differential DQS pair in a source
synchronous fashion.
These devices operate with a single 1.5V ± 0.075V and 1.35V -0.0675V/+0.1V power supply and are available in BGA
packages.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
2
REV 1.1
08 / 2010
Pin Configuration 78 balls BGA Package (x4)
< TOP View>
See the balls through the package
A
B
C
D
E
F
G
x 4
1
VSS
VSSQ
VDD
VSSQ
DQ2
NC
VDDQ
VSS

2
NC
DQ0
DQS

NC


3 7 8 9
BA0
VDD
NC
VSS
VSSQ
DQ3
VSS
NC
VSS
VDD
NC
DM
DQ1
NC
CK

VDDQ
H
J
K
L
VSS
VDDQ
VREFDQ
A3
A 5VSS
VDD

BA2
A0
A2 A1
A12/
NC
A10/AP
VDD
A4
BA1
VERFCA
ZQ
VDDQ
VSSQ
VSSQ
VDD
ODT
VSS
NC
M
N
VDD A7

A9
A13
VDDA6
A8
A11
A14VSS VSS
NC
NC
VDD
VSS
VSS
CKE
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
3
REV 1.1
08 / 2010
Pin Configuration 78 balls BGA Package (x8)
< TOP View>
See the balls through the package
A
B
C
D
E
F
G
x 8
1
VSS
VSSQ
VDD
VSSQ
DQ2
DQ6
VDDQ
VSS

2
NC
DQ0
DQS

DQ4


3 7 8 9
BA0
VDD
NC
VSS
VSSQ
DQ3
VSS
DQ5
VSS
VDD
NU/
DM/TDQS
DQ1
DQ7
CK

VDDQ
H
J
K
L
VSS
VDDQ
VREFDQ
A3
A 5VSS
VDD

BA2
A0
A2 A1
A12/ 
NC
A10/AP
VDD
A4
BA1
VERFCA
ZQ
VDDQ
VSSQ
VSSQ
VDD
ODT
VSS
NC
M
N
VDD A7

A9
A13
VDDA6
A8
A11
A14VSS VSS
NC
NC
VDD
VSS
VSS
CKE
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
4
REV 1.1
08 / 2010
Pin Configuration 96 balls BGA Package (x16)
< TOP View>
See the balls through the package
A
B
C
D
E
F
G
x 16
1
VDDQ
VSSQ
DQU5
VDD
DQU3
VDDQ
VSSQ
DQL2
2
DQU7
VSS
DQU1
UDM
DQL0
DQSL

3 7 8 9
VSS
VSS
VDDQ
VDDQ
DQU6
DQU2
VSSQ
VSSQ
DQL3
VSS
DQU4

DQSU
DML
DQL1
VDD
VDDQ
H
J
K
L
VSSQ
VDDQ
VSS
VDD
NC
DQL6
DQL4


 A10/AP

CK
DQL7
DQU0
ZQ
VDD
VSS
DQL5
VSSQ
VDDQ
VDD
CKE
VSSQ
NC
VSSQ
M
N
VSS BA0
A3
BA2
A0
VSSVREFCA
BA1
A15
A12/BC#VDD VDD
VDDQ
VREFDQ
ODT
NC
NC
VSSQ
PA5VSS A2 A1 A4
R
T
VDD A7

A9
A13
VDDA6
A8
A11
A14VSS VSS
VSS
VDDQ
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
5
REV 1.1
08 / 2010
Input / Output Functional Description
Symbol
Type
Function
CK, 
Input
Clock: CK and  are differential clock inputs. All address and control input signals are sampled on
the crossing of the positive edge of CK and negative edge of .
CKE
Input
Clock Enable: CKE high activates, and CKE low deactivates, internal clock signals and device input
buffers and output drivers. Taking CKE low provides Precharge Power-Down and Self-Refresh
operation (all banks idle), or Active Power-Down (row Active in any bank). CKE is synchronous for
power down entry and exit and for Self-Refresh entry. CKE is asynchronous for Self-Refresh exit.
After VREF has become stable during the power on and initialization sequence, it must be maintained
for proper operation of the CKE receiver. For proper self-refresh entry and exit, VREF must maintain
to this input. CKE must be maintained high throughout read and write accesses. Input buffers,
excluding CK, , ODT and CKE are disabled during Power Down. Input buffers, excluding CKE, are
disabled during Self-Refresh.

Input
Chip Select: All commands are masked when  is registered high.  provides for external rank
selection on systems with multiple memory ranks.  is considered part of the command code.
, , 
Input
Command Inputs: ,  and  (along with ) define the command being entered.
DM, (DMU, DML)
Input
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is
sampled HIGH coincident with that input data during a Write access. DM is sampled on both edges
of DQS. For x8 device, the function of DM or TDQS /  is enabled by Mode Register A11 setting
in MR1
BA0 - BA2
Input
Bank Address Inputs: BA0, BA1, and BA2 define to which bank an Active, Read, Write or
Precharge command is being applied. Bank address also determines which mode register is to be
accessed during a MRS cycle.
A0 A14
Input
Address Inputs: Provide the row address for Activate commands and the column address for
Read/Write commands to select one location out of the memory array in the respective bank.
(A10/AP and A12/ have additional function as below. The address inputs also provide the op-code
during Mode Register Set commands.
A12 / 
Input
Burst Chop: A12/ is sampled during Read and Write commands to determine if burst chop (on
the fly) will be performed. (HIGH - no burst chop; LOW - burst chopped).
DQ
Input/output
Data Inputs/Output: Bi-directional data bus.
DQL,
DQU,
DQS,(),
DQSL,(),
DQSU,(),
Input/output
Data Strobe: output with read data, input with write data. Edge aligned with read data, centered
with write data. The data strobes DQS, DQSL, DQSU are paired with differential signals , ,
, respectively, to provide differential pair signaling to the system during both reads and writes.
DDR3 SDRAM supports differential data strobe only and does not support single-ended.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
6
REV 1.1
08 / 2010
Symbol
Type
Function
ODT
Input
On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR3
SDRAM. When enabled, ODT is applied to each DQ, DQS,  and DM/TDQS, NU/ (when
TDQS is enabled via Mode Register A11=1 in MR1) signal for x8 configurations. The ODT pin will be
ignored if Mode-registers, MR1and MR2, are programmed to disable RTT.

Input
Active Low Asynchronous Reset: Reset is active when  is LOW, and inactive when 
is HIGH.  must be HIGH during normal operation.  is a CMOS rail to rail signal with DC
high and low at 80% and 20% of VDD, i.e. 1.20V for DC high and 0.30V
NC
No Connect: No internal electrical connection is present.
VDDQ
Supply
DQ Power Supply: 1.5V ± 0.075V , 1.35V -0.0675V/+0.1V
VDD
Supply
Power Supply: 1.5V ± 0.075V, 1.35V -0.0675V/+0.1V
VSSQ
Supply
DQ Ground
Vss
Supply
Ground
VREFCA
Supply
Reference voltage for CA
VREFDQ
Supply
Reference voltage for DQ
ZQ
Supply
Reference pin for ZQ calibration.
Note: Input only pins (BA0-BA2, A0-A13, , , , , CKE, ODT, and ) do not supply termination.
DDR3 SDRAM Addressing
Configuration
NT5CB256M8BN
NT5CC256M8BN
NT5CB128M16BP
NT5CC128M16BP
# of Bank
8
8
Bank Address
BA0 BA2
BA0 BA2
Auto precharge
A10 / AP
A10 / AP
BL switch on the fly
A12 / 
A12 / 
Row Address
A0 A14
A0 A13
Column Address
A0 A9
A0 A9
Page size
1KB
2KB
Note:
Page size is the number of data delivered from the array to the internal sense amplifiers when an ACTIVE command is
registered. Page size is per bank, calculated as follows:
Page size = 2 COLBITS * ORG / 8
COLBITS = the number of column address bits
ORG = the number of I/O (DQ) bits
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
7
REV 1.1
08 / 2010
Ordering Information
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
Organization
VDD
Part Number
Package
Speed
Clock
(Mbp/s)
Data Rate
(Mb/s)
CL-TRCD-TRP
512M x 4
1.5V
NT5CB512M4BN-AC
78-Ball WBGA
0.8mmx0.8mm
Pitch
400
DDR3-800
5-5-5
NT5CB512M4BN-AD
400
DDR3-800
6-6-6
NT5CB512M4BN-BE
533
DDR3-1066
7-7-7
NT5CB512M4BN-CG
667
DDR3-1333
9-9-9
NT5CB512M4BN-DI
800
DDR3-1600
11-11-11
256M x 8
NT5CB256M8BN-AC
400
DDR3-800
5-5-5
NT5CB256M8BN -AD
400
DDR3-800
6-6-6
NT5CB256M8BN-BE
533
DDR3-1066
7-7-7
NT5CB256M8BN-CG
667
DDR3-1333
9-9-9
NT5CB256M8BN-DI
800
DDR3-1600
11-11-11
128M x 16
NT5CB128M16BP-AC
96-Ball WBGA
0.8mmx0.8mm
Pitch
400
DDR3-800
5-5-5
NT5CB128M16BP-AD
400
DDR3-800
6-6-6
NT5CB128M16BP-BE
533
DDR3-1066
7-7-7
NT5CB128M16BP-CG
667
DDR3-1333
9-9-9
NT5CB128M16BP-DI
800
DDR3-1600
11-11-11
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
8
REV 1.1
08 / 2010
Ordering Information
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
Organization
VDD
Part Number
Package
Speed
Clock
(Mbp/s)
Data Rate
(Mb/s)
CL-TRCD-TRP
512M x 4
1.35V
NT5CC512M4BN-AC
78-Ball WBGA
0.8mmx0.8mm
Pitch
400
DDR3-800
5-5-5
NT5CC512M4BN-AD
400
DDR3-800
6-6-6
NT5CC512M4BN-BE
533
DDR3-1066
7-7-7
NT5CC512M4BN-CG
667
DDR3-1333
9-9-9
NT5CC512M4BN-DI
800
DDR3-1600
11-11-11
256M x 8
NT5CC256M8BN-AC
400
DDR3-800
5-5-5
NT5CC256M8BN -AD
400
DDR3-800
6-6-6
NT5CC256M8BN-BE
533
DDR3-1066
7-7-7
NT5CC256M8BN-CG
667
DDR3-1333
9-9-9
NT5CC256M8BN-DI
800
DDR3-1600
11-11-11
128M x 16
NT5CC128M16BP-AC
96-Ball WBGA
0.8mmx0.8mm
Pitch
400
DDR3-800
5-5-5
NT5CC128M16BP-AD
400
DDR3-800
6-6-6
NT5CC128M16BP-BE
533
DDR3-1066
7-7-7
NT5CC128M16BP-CG
667
DDR3-1333
9-9-9
NT5CC128M16BP-DI
800
DDR3-1600
11-11-11
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
9
REV 1.1
08 / 2010
Simplified State Diagram
Power
ON
Power
Applied Reset
Procedure
From any
State RESET
Initialization
ZQ Calibration Idle
MRS, MPR,
Write
Levelizing Self Refresh
Refreshing
SRE
SRX
REF
Activating
ACT
Precharge
Power
Down
PDE
PDX
Active
Power
Down
Bank
Active
Writing
Writing
Precharging
Reading
Write
Write A Read A
Write Read
Write A Read A
Write
Read
PRE,
PREA PRE,
PREA
Write A Read A
PRE,
PREA
PDX
PDE
Reading
Read
Automatic
Sequence
Command
Sequence
MRSZQCL
ZQCL
ZQCS
Abbreviation Function Abbreviation Function Abbreviation Function
ACT Active Read RD, RDS4, RDS8 PED Enter Power-down
PRE Precharge Read A RDA, RDAS4, RDAS8 PDX Exit Power-down
PREA Precharge All Write WR, WRS4, WRS8 SRE Self-Refresh entry
MRS Mode Register Set Write A WRA, WRAS4, WRAS8 SRX Self-Refresh exit
REF Refresh  Start RESET Procedure MPR Multi-Purpose Register
ZQCL ZQ Calibration Long ZQCS ZQ Calibration Short - -
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
10
REV 1.1
08 / 2010
Basic Functionality
The DDR3 SDRAM is a high-speed dynamic random access memory internally configured as an eight-bank DRAM. The
DDR3 SDRAM uses an 8n prefetch architecture to achieve high speed operation. The 8n prefetch architecture is
combined with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write
operation for the DDR3 SDRAM consists of a single 8n-bit wide, four clock data transfer at the internal DRAM core and
two corresponding n-bit wide, one-half clock cycle data transfers at the I/O pins.
Read and write operation to the DDR3 SDRAM are burst oriented, start at a selected location, and continue for a burst
length of eight or a „chopped‟ burst of four in a programmed sequence. Operation begins with the registration of an Active
command, which is then followed by a Read or Write command. The address bits registered coincident with the Active
command are used to select the bank and row to be activated (BA0-BA2 select the bank; A0-A13 select the row). The
address bit registered coincident with the Read or Write command are used to select the starting column location for the
burst operation, determine if the auto precharge command is to be issued (via A10), and select BC4 or BC8 mode „on the
fly‟ (via A12) if enabled in the mode register.
Prior to normal operation, the DDR3 SDRAM must be powered up and initialized in a predefined manner. The following
sections provide detailed information covering device reset and initialization, register definition, command descriptions
and device operation.
DRAM Initialization and RESET
Power-up Initialization sequence
The Following sequence is required for POWER UP and Initialization
1. Apply power ( is recommended to be maintained below 0.2 x VDD, all other inputs may be undefined). 
needs to be maintained for minimum 200μs with stable power. CKE is pulled “Low” anytime before  being
de-asserted (min. time 10ns). The power voltage ramp time between 300mV to VDDmin must be no greater than 200ms;
and during the ramp, VDD>VDDQ and (VDD-VDDQ) <0.3 Volts.
- VDD and VDDQ are driven from a single power converter output, AND
- The voltage levels on all pins other than VDD, VDDQ, VSS, VSSQ must be less than or equal to VDDQ and VDD on one
side and must be larger than or equal to VSSQ and VSS on the other side. In addition, VTT is limited to 0.95V max once
power ramp is finished, AND
- Vref tracks VDDQ/2.
OR
- Apply VDD without any slope reversal before or at the same time as VDDQ.
- Apply VDDQ without any slope reversal before or at the same time as VTT & Vref.
- The voltage levels on all pins other than VDD, VDDQ, VSS, VSSQ must be less than or equal to VDDQ and VDD on one
side and must be larger than or equal to VSSQ and VSS on the other side.
2. After  is de-asserted, wait for another 500us until CKE become active. During this time, the DRAM will start
internal state initialization; this will be done independently of external clocks.
3. Clock (CK, ) need to be started and stabilized for at least 10ns or 5tCK (which is larger) before CKE goes active.
Since CKE is a synchronous signal, the corresponding set up time to clock (tIS) must be meeting. Also a NOP or Deselect
command must be registered (with tIS set up time to clock) before CKE goes active. Once the CKE registered “High” after
Reset, CKE needs to be continuously registered “High” until the initialization sequence is finished, including expiration of
tDLLK and tZQinit.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
11
REV 1.1
08 / 2010
4. The DDR3 DRAM will keep its on-die termination in high impedance state as long as  is asserted. Further, the
DRAM keeps its on-die termination in high impedance state after  de-assertion until CKE is registered HIGH. The
ODT input signal may be in undefined state until tIS before CKE is registered HIGH. When CKE is registered HIGH, the
ODT input signal may be statically held at either LOW or HIGH. If RTT_NOM is to be enabled in MR1, the ODT input
signal must be statically held LOW. In all cases, the ODT input signal remains static until the power up initialization
sequence is finished, including the expiration of tDLLK and tZQinit.
5. After CKE being registered high, wait minimum of Reset CKE Exit time, tXPR, before issuing the first MRS command
to load mode register. [tXPR=max(tXS, 5tCK)]
6. Issue MRS command to load MR2 with all application settings. (To issue MRS command for MR2, provide “Low” to
BA0 and BA2, “High” to BA1)
7. Issue MRS command to load MR3 with all application settings. (To issue MRS command for MR3, provide “Low” to
BA2, “High” to BA0 and BA1)
8. Issue MRS command to load MR1 with all application settings and DLL enabled. (To issue “DLL Enablecommand,
provide “Low” to A0, “High” to BA0 and “Low” to BA1 and BA2)
9. Issue MRS Command to load MR0 with all application settings and “DLL reset”. (To issue DLL reset command,
provide “High” to A8 and “Low” to BA0-BA2)
10. Issue ZQCL command to starting ZQ calibration.
11. Wait for both tDLLK and tZQinit completed.
12. The DDR3 SDRAM is now ready for normal operation.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
12
REV 1.1
08 / 2010
DDR3 Reset and Initialization Sequence at Power-on Ramping
CK
CK
tCKSRX
RESET
CKE
tIS
ODT
Command
BA0-BA2
T=200us T=500us tXPR tMRD tMRD tMRD tMOD tZQinit.
Do Not
Care Time break
10ns
MRSMRS MRS MRS ZQCL
MR2 MR3 MR1 MR0
VDD,
VDDQ
* From time point Td until Tk. NOP or DES commands must be applied between MRS and ZQcal commnads.
Te Tk
NOP* NOP* Valid
Valid
Static LOW in case RTT_Nom is enabled at time Tg, otherwise static HIGH or LOW
TdTcTa Tb Tf Tg Th Ti Tj
tDLLK
Valid
Valid
DDR3 Reset Procedure at Power Stable Condition
The following sequence is required for RESET at no power interruption initialization.
1. Asserted RESET below 0.2*VDD anytime when reset is needed (all other inputs may be undefined). RESET needs to be
maintained for minimum 100ns. CKE is pulled “Low” before RESET being de-asserted (min. time 10ns).
2. Follow Power-up Initialization Sequence step 2 to 11.
3. The Reset sequence is now completed. DDR3 SDRAM is ready for normal operation.
CK
CK
tCKSRX
RESET
CKE
tIS
ODT
Command
BA0-BA2
T=100ns
T=500us
tXPR
tMRD
tMRDtMRDtMOD
tZQinit.
Do Not
Care
Time break
10ns
MRSMRSMRSMRSZQCL
MR2MR3MR1MR0
VDD,
VDDQ
* From time point Td until Tk. NOP or DES commands must be applied between MRS and ZQcal commnads.
Te Tk
NOP* NOP*
Valid
Valid
Static LOW in case RTT_Nom is enabled at time Tg, otherwise static HIGH or LOW
TdTcTaTb TfTgThTiTj
tDLLK
Valid
Valid
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
13
REV 1.1
08 / 2010
Register Definition
Programming the Mode Registers
For application flexibility, various functions, features, and modes are programmable in four Mode Registers, provided by the
DDR3 SDRAM, as user defined variables and they must be programmed via a Mode Register Set (MRS) command. As the
default values of the Mode Registers (MR#) are not defined, contents of Mode Registers must be fully initialized and/or
re-initialized, i.e. written, after power up and/or reset for proper operation. Also the contents of the Mode Registers can be
altered by re-executing the MRS command during normal operation. When programming the mode registers, even if the
user chooses to modify only a sub-set of the MRS fields, all address fields within the accessed mode register must be
redefined when the MRS command is issued. MRS command and DLL Reset do not affect array contents, which means
these commands can be executed any time after power-up without affecting the array contents
The mode register set command cycle time, tMRD is required to complete the write operation to the mode register and is the
minimum time required between two MRS commands shown as below.
CK
CK
CKE
Do not
Care Time break
MRS NOP NOP NOP NOPCMD
VAL VALADDR
tMRD
MRS
The MRS command to Non-MRS command delay, tMOD, is require for the DRAM to update the features except DLL reset,
and is the minimum time required from an MRS command to a non-MRS command excluding NOP and DES shown as the
following figure.
CK
CK
CKE
MRS NOP NOP NOP NOPCMD
ADDR
tMOD
Non
MRS
VAL
Old Setting Updating Setting New Setting
VAL
VAL
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
14
REV 1.1
08 / 2010
The mode register contents can be changed using the same command and timing requirements during normal operation as
long as the DRAM is in idle state, i.e. all banks are in the precharged state with tRP satisfied, all data bursts are completed
and CKE is high prior to writing into the mode register. The mode registers are divided into various fields depending on the
functionality and/or modes.
The mode-register MR0 stores data for controlling various operating modes of DDR3 SDRAM. It controls burst length, read
burst type, CAS latency, test mode, DLL reset, WR, and DLL control for precharge Power-Down, which include various
vendor specific options to make DDR3 SDRAM useful for various applications. The mode register is written by asserting
low on , , , , BA0, BA1, and BA2, while controlling the states of address pins according to the following
figure.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
15
REV 1.1
08 / 2010
MR0 Definition
A0A1A2A3A4A5A6A7A8A9A10A11A12A13BA0BA1BA2
Address Filed
BL
A0A1
8 (Fixed)00
BC4 or 8
(on the fly)
10
Burst Length
Burst TypeA3
Nibble
Sequential
0
Interleave
1
Burst Type
MRS mode
BA0BA1
MR000
10
MRS mode
01
11
DLL Control for
Precharge PD
A12
Slow Exit (Low Power)0
Fast Exit (Normal)
1
Precharge Power Down
* *
WR(cycles)A9A10A11
16000
5
100
Write recovery for autoprecharge**
010
110
001
101
011
111
DLL ResetA8
NO0
YES
1
DLL Reset ModeA7
Normal0
TEST
1
Mode
* BA2 and A13 are reserved for future use and must be set to 0 when
programming the MR.
**WR(write recovery for autoprecharge)min in clock cycles is calculated by
dividing tWR (ns) by tCK (ns) and rounding up to the next integer:
Wrmin[cycles] = Roundup(tWR/tCK). The value in the mode register must
be programmed to be equal or larger than WRmin. The programmed WR
value is used with tRP to determine tDAL.
CAS LatencyA2A4A5
000
50
CAS Latency
01
11
BC4 (Fixed)
Reserved
Reserved
A6
0
0 1 0
0 1 0 0
0 1 1 0
1 0 0 0
1 0 1 0
1 1 0 0
1 1 1 0
6
7
8
9
10
11
6
7
8
10
12
14
MR1
MR2
MR3
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
16
REV 1.1
08 / 2010
Burst Length, Type, and Order
Accesses within a given burst may be programmed to sequential or interleaved order. The burst type is selected via bit A3
as shown in the MR0 Definition as above figure. The ordering of access within a burst is determined by the burst length,
burst type, and the starting column address. The burst length is defined by bits A0-A1. Burst lengths options include fix BC4,
fixed BL8, and on the fly which allow BC4 or BL8 to be selected coincident with the registration of a Read or Write
command via A12/.
Burst Type and Burst Order
Burst
Length
Read
Write
Starting
Column
Address
(A2,A1,A0)
Burst type:
Sequential
(decimal)
A3 = 0
Burst type:
Interleaved
(decimal)
A3 = 1
Note
4
Chop
Read
0 , 0 , 0
0,1,2,3,T,T,T,T
0,1,2,3,T,T,T,T
1,2,3
0 , 0 , 1
1,2,3,0,T,T,T,T
1,0,3,2,T,T,T,T
0 , 1 , 0
2,3,0,1,T,T,T,T
2,3,0,1,T,T,T,T
0 , 1 , 1
3,0,1,2,T,T,T,T
3,2,1,0,T,T,T,T
1 , 0 , 0
4,5,6,7,T,T,T,T
4,5,6,7,T,T,T,T
1 , 0 , 1
5,6,7,4,T,T,T,T
5,4,7,6,T,T,T,T
1 , 1 , 0
6,7,4,5,T,T,T,T
6,7,4,5,T,T,T,T
1 , 1 , 1
7,4,5,6,T,T,T,T
7,6,5,4,T,T,T,T
Write
0 , V , V
0,1,2,3,X,X,X,X
0,1,2,3,X,X,X,X
1,2,4,5
1 , V , V
4,5,6,7,X,X,X,X
4,5,6,7,X,X,X,X
8
Read
0 , 0 , 0
0,1,2,3,4,5,6,7
0,1,2,3,4,5,6,7
2
0 , 0 , 1
1,2,3,0,5,6,7,4
1,0,3,2,5,4,7,6
0 , 1 , 0
2,3,0,1,6,7,4,5
2,3,0,1,6,7,4,5
0 , 1 , 1
3,0,1,2,7,4,5,6
3,2,1,0,7,6,5,4
1 , 0 , 0
4,5,6,7,0,1,2,3
4,5,6,7,0,1,2,3
1 , 0 , 1
5,6,7,4,1,2,3,0
5,4,7,6,1,0,3,2
1 , 1 , 0
6,7,4,5,2,3,0,1
6,7,4,5,2,3,0,1
1 , 1 , 1
7,4,5,6,3,0,1,2
7,6,5,4,3,2,1,0
Write
V , V , V
0,1,2,3,4,5,6,7
0,1,2,3,4,5,6,7
2,4
Note:
1. In case of burst length being fixed to 4 by MR0 setting, the internal write operation starts two clock cycles earlier
than the BL8 mode. This means that the starting point for tWR and tWTR will be pulled in by two clocks. In case of
burst length being selected on-the-fly via A12/, the internal write operation starts at the same point in time like a
burst of 8 write operation. This means that during on-the-fly control, the starting point for tWR and tWTR will not be
pulled in by two clocks.
2. 0~7 bit number is value of CA[2:0] that causes this bit to be the first read during a burst.
3. T: Output driver for data and strobes are in high impedance.
4. V: a valid logic level (0 or 1), but respective buffer input ignores level on input pins.
5. X: Do not Care.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
17
REV 1.1
08 / 2010
CAS Latency
The CAS Latency is defined by MR0 (bit A9~A11) as shown in the MR0 Definition figure. CAS Latency is the delay, in clock
cycles, between the internal Read command and the availability of the first bit of output data. DDR3 SDRAM does not
support any half clock latencies. The overall Read Latency (RL) is defined as Additive Latency (AL) + CAS Latency (CL);
RL = AL + CL.
Test Mode
The normal operating mode is selected by MR0 (bit7=0) and all other bits set to the desired values shown in the MR0
definition figure. Programming bit A7 to a 1‟ places the DDR3 SDRAM into a test mode that is only used by the DRAM
manufacturer and should not be used. No operations or functionality is guaranteed if A7=1.
DLL Reset
The DLL Reset bit is self-clearing, meaning it returns back to the value of „0‟ after the DLL reset function has been issued.
Once the DLL is enabled, a subsequent DLL Reset should be applied. Anytime the DLL reset function is used, tDLLK must
be met before any functions that require the DLL can be used (i.e. Read commands or ODT synchronous operations.)
Write Recovery
The programmed WR value MR0(bits A9, A10, and A11) is used for the auto precharge feature along with tRP to determine
tDAL WR (write recovery for auto-precharge)min in clock cycles is calculated by dividing tWR(ns) by tCK(ns) and rounding
up to the next integer: WRmin[cycles] = Roundup(tWR[ns]/tCK[ns]). The WR must be programmed to be equal or larger
than tWR(min).
Precharge PD DLL
MR0 (bit A12) is used to select the DLL usage during precharge power-down mode. When MR0 (A12=0), or „slow-exit‟, the
DLL is frozen after entering precharge power-down (for potential power savings) and upon exit requires tXPDLL to be met
prior to the next valid command. When MR0 (A12=1), or „fast-exit‟, the DLL is maintained after entering precharge
power-down and upon exiting power-down requires tXP to be met prior to the next valid command.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
18
REV 1.1
08 / 2010
Mode Register MR1
The Mode Register MR1 stores the data for enabling or disabling the DLL, output strength, Rtt_Nom impedance, additive
latency, WRITE leveling enable and Qoff. The Mode Register 1 is written by asserting low on , , ,  high on
BA0 and low on BA1 and BA2, while controlling the states of address pins according to the following figure.
A0A1A2A3A4A5A6A7A8A9A10A11A12A13BA0BA1BA2
Address Filed
DLL
Enable
A0
Enable
0
Disable1
DLL
Output Driver
Impedance Control
MR
BA0BA1
MR0
00
MR1
10
Mode Register
01
11 MR3
MR2
Qoff
* *
* BA2, A5, A8, A10, and A13 are reserved for future use and must be
set to 0 when programming the MR.
** Outputs disabled DQs, DQSs, DQSs.
*** In Write leveling Mode (MR1[bit7]=1) with MR1[bit12]=1, all RTT_Nom
settings are allowed; in Write Leveling Mode (MR1[bit7]=1) with
MR1[bit12]=0, only RTT_Nom settin gof RZQ/2, RZQ/4, and RZQ/6 are
allowed.
**** If RTT_Nom is used during Writes, only the values RZQ/2, RZQ/4, RZQ/6
are allowed.
QoffA12
Output buffer enabled0
Output buffer disabled
1
ALA3A4
0 (AL disable)00
CL-1
10
Additive Latency
01
11
Rtt_Nom A2A6A9
ODT Disable000
100
010
110
001
101
011
111
ODT value
RZQ/4
RZQ/2
RZQ/6
RZQ/12
RZQ/8
Reserved
Reserved
*
CL-2
Reserved
* *
Write Levelization
Write leveling enableA7
Disabled0
Enabled
1
TDQS
TDQS enableA11
Disabled0
Enabled
1
D.I.C.A1A5
Reserved for
RZQ/6
00
RZQ/7
10
01
11 RZQ/TBD
RZQ/TBD
**
***
Note: RZQ=240ohms
****
****
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
19
REV 1.1
08 / 2010
DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during power up initialization, and upon returning to
normal operation after having the DLL disabled. During normal operation (DLL-on) with MR1 (A0=0), the DLL is
automatically disabled when entering Self-Refresh operation and is automatically re-enable upon exit of Self-Refresh
operation. Any time the DLL is enabled and subsequently reset, tDLLK clock cycles must occur before a Read or
synchronous ODT command can be issued to allow time for the internal clock to be synchronized with the external clock.
Failing to wait for synchronization to occur may result in a violation of the tDQSCK, tAON, or tAOF parameters. During
tDLLK, CKE must continuously be registered high. DDR3 SDRAM does not require DLL for any Write operation, expect
when RTT_WR is enabled and the DLL is required for proper ODT operation. For more detailed information on DLL Disable
operation in DLL-off Mode.
The direct ODT feature is not supported during DLL-off mode. The on-die termination resistors must be disabled by continu-
ously registering the ODT pin low and/or by programming the RTT_Nom bits MR1{A9,A6,A2} to {0,0,0} via a mode register
set command during DLL-off mode.
The dynamic ODT feature is not supported at DLL-off mode. User must use MRS command to set Rtt_WR,
MR2{A10,A9}={0,0}, to disable Dynamic ODT externally.
Output Driver Impedance Control
The output driver impedance of the DDR3 SDRAM device is selected by MR1(bit A1 and A5) as shown in MR1 definition
figure.
ODT Rtt Values
DDR3 SDRAM is capable of providing two different termination values (Rtt_Nom and Rtt_WR). The nominal termination
value Rtt_Nom is programmable in MR1. A separate value (Rtt_WR) may be programmable in MR2 to enable a unique Rtt
value when ODT is enabled during writes. The Rtt_WR value can be applied during writes even when Rtt_Nom is disabled.
Additive Latency (AL)
Additive Latency (AL) operation is supported to make command and data bus efficient for sustainable bandwidth in DDR3
SDRAM. In this operation, the DDR3 SDRAM allows a read or write command (either with or without auto-precharge) to be
issued immediately after the active command. The command is held for the time of the Additive Latency (AL) before it is
issued inside the device. The Read Latency (RL) is controlled by the sum of the AL and CAS Latency (CL) register settings.
Write Latency (WL) is controlled by the sum of the AL and CAS Write Latency (CWL) register settings. A summary of the AL
register options are shown as the following table.
Additive Latency (AL) Settings
A4
A3
AL
0
0
0, (AL Disable)
0
1
CL-1
1
0
CL-2
1
1
Reserved
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
20
REV 1.1
08 / 2010
Write leveling
For better signal integrity, DDR3 memory module adopted fly by topology for the commands, addresses, control signals,
and clocks. The fly by topology has benefits from reducing number of stubs and their length but in other aspect, causes
flight time skew between clock and strobe at every DRAM on DIMM. It makes difficult for the Controller to maintain tDQSS,
tDSS, and tDSH specification. Therefore, the controller should support „write leveling‟ in DDR3 SDRAM to compensate for
skew.
Output Disable
The DDR3 SDRAM outputs maybe enable/disabled by MR1 (bit12) as shown in MR1 definition. When this feature is
enabled (A12=1) all output pins (DQs, DQS, , etc.) are disconnected from the device removing any loading of the
output drivers. This feature may be useful when measuring modules power for example. For normal operation A12 should
be set to „0‟.
TDQS, 
TDQS (Termination Data Strobe) is a feature of x8 DDR3 SDRAM that provides additional termination resistance outputs
that may be useful in some system configurations.
TDQS is not supported in x4 configurations. When enabled via the mode register, the same termination resistance function
is applied to be TDQS/ pins that are applied to the DQS/ pins.
In contrast to the RDQS function of DDR2 SDRAM, TDQS provides the termination resistance function only. The data
strobe function of RDQS is not provided by TDQS.
The TDQS and DM functions share the same pin. When the TDQS function is enabled via the mode register, the DM
function is not supported. When the TDQS function is disabled, the DM function is provided and the  pin is not used.
The TDQS function is available in x8 DDR3 SDRAM only and must be disabled via the mode register A11=0 in MR1 for x4
configurations.
TDQS,  Function Matrix
MR1 (A11)
DM / TDQS
NU / TDQS
0 (TDQS Disabled)
DM
Hi-Z
1 (TDQS Enabled)
TDQS
TDQS
Note:
1. If TDQS is enabled, the DM function is disabled.
2. When not used, TDQS function can be disabled to save termination power.
3. TDQS function is only available for x8 DRAM and must be disabled for x4
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
21
REV 1.1
08 / 2010
Mode Register MR2
The Mode Register MR2 stores the data for controlling refresh related features, Rtt_WR impedance, and CAS write latency.
The Mode Register 2 is written by asserting low on , , ,  high on BA1 and low on BA0 and BA2, while
controlling the states of address pins according to the table below.
A0A1A2A3A4A5A6A7A8A9A10A11A12A13BA0BA1BA2
Address Filed
MRS modeBA0BA1
MR000
10
MRS mode
01
11
*
*BA2, A5, A8, A13 are reserved for future use and must be set to 0 when programming the MR .
** The Rtt _WR value can be applied during writes even when Rtt _Nom is disabled . During write leveling , Dynamic ODT is
not available .
MR1
MR2
MR3
CAS Write LatencyA3A4
00
6
(2.5ns>tCK(avg)>=1.875ns)
0
CAS Write Latency
5
(tCK(avg)>=2.5ns)
A5
0
0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
7
(1.875ns>tCK(avg)>=1.5ns)
8
(1.5ns>tCK(avg)>=1.25ns)
Reserved
Reserved
Reserved
Reserved
PASRA0A1
00
Half Array
(000,001,010,011)
0
PASR
Full Array
A2
0
0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
Quarter Array
(000,001)
1/8th Array (000)
3/4 array
(010,011,100,101,
110,111)
Half array
(100,101,110,111)
Quarter array
(110,111)
1/8th array (111)
ASRA6
Manual Self Refresh Reference0
ASR Enable
1
Auto Self Refresh
SRTA7
Normal Operating temperature
range
0
Extended operating temperature
range
1
Self-Refresh Temperature Range
A9A10
Dynamic ODT off (Write does
not affect RTT value )
00
10
01
11
RZQ/4
Reserved
Rtt_WR**
Rtt_WR
RZQ/2
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
22
REV 1.1
08 / 2010
CAS Write Latency (CWL)
The CAS Write Latency is defined by MR2 (bits A3-A5) shown in MR2. CAS Write Latency is the delay, in clock cycles,
between the internal Write command and the availability of the first bit of input data. DDR3 DRAM does not support any half
clock latencies. The overall Write Latency (WL) is defined as Additive Latency (AL) + CAS Write Latency (CWL);
WL=AL+CWL.
For more information on the supported CWL and AL settings based on the operating clock frequency, refer to “Standard
Speed Bins” on page159. For detailed Write operation refer to “WRITE Operation” on page70.
Auto Self-Refresh (ASR) and Self-Refresh Temperature (SRT)
DDR3 SDRAM must support Self-Refresh operation at all supported temperatures. Applications requiring Self-Refresh
operation in the Extended Temperature Range must use the ASR function or program the SRT bit appropriately.
Optional in DDR3 SDRAM: Users should refer to the DRAM supplier data sheet and/or the DIMM SPD to determine if
DDR3 SDRAM devices support the following options or requirements referred to in this material. For more details refer to
“Extended Temperature Usage” on page48. DDR3 SDRAMs must support Self-Refresh operation at all supported
temperatures. Applications requiring Self-Refresh operation in the Extended Temperature Range must use the optional
ASR function or program the SRT bit appropriately.
Dynamic ODT (Rtt_WR)
DDR3 SDRAM introduces a new feature “Dynamic ODT”. In certain application cases and to further enhance signal
integrity on the data bus, it is desirable that the termination strength of the DDR3 SDRAM can be changed without issuing
an MRS command. MR2 Register locations A9 and A10 configure the Dynamic ODT settings. In Write leveling mode, only
RTT_Nom is available. For details on Dynamic ODT operation, refer to “Dynamic ODT” on page69.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
23
REV 1.1
08 / 2010
Mode Register MR3
The Mode Register MR3 controls Multi-purpose registers. The Mode Register 3 is written by asserting low on , , ,
 high on BA1 and BA0, and low on BA2 while controlling the states of address pins according to the table below.
A0A1A2A3A4A5A6A7A8A9A10A11A12A13BA0BA1BA2
Address Filed
MRS modeBA0BA1
MR000
10
MRS mode
01
11
Note: BA2, A3-A13 are reserved for future use and must be
set to 0 when programming the MR.
MR1
MR2
MR3
MPRA2
Normal Operation0
Dataflow from MPR
1
MPR
MPR Loc.A0A1
00
RFU0
MPR Location
Predefined pattern
1
1 0
1 1
RFU
Thermal Sensor Readout
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
24
REV 1.1
08 / 2010
Multi-Purpose Register (MPR)
The Multi Purpose Register (MPR) function is used to Read out a predefined system timing calibration bit sequence. To
enable the MPR, a Mode Register Set (MRS) command must be issued to MR3 register with bit A2=1. Prior to issuing the
MRS command, all banks must be in the idle state (all banks precharged and tRP met). Once the MPR is enabled, any
subsequent RD or RDA commands will be redirected to the Multi Purpose Register. When the MPR is enabled, only RD or
RDA commands are allowed until a subsequent MRS command is issued with the MPR disabled (MR3 bit A2=0). Power
down mode, Self-Refresh and any other non-RD/RDA command is not allowed during MPR enable mode. The RESET
function is supported during MPR enable mode.
The Multi Purpose Register (MPR) function is used to Read out a predefined system timing calibration bit sequence. The
basic concept of the MPR is shown in Figure20.
To enable the MPR, a MODE Register Set (MRS) command must be issued to MR3 Register with bit A2 = 1, as shown in
Table12. Prior to issuing the MRS command, all banks must be in the idle state (all banks precharged and tRP met). Once
the MPR is enabled, any subsequent RD or RDA commands will be redirected to the Multi Purpose Register. The resulting
operation, when a RD or RDA command is issued, is defined by MR3 bits A[1:0] when the MPR is enabled as shown in
Table13. When the MPR is enabled, only RD or RDA commands are allowed until a subsequent MRS command is issued
with the MPR disabled (MR3 bit A2 = 0). Note that in MPR mode RDA has the same functionality as a READ command
which means the auto precharge part of RDA is ignored. Power-Down mode, Self-Refresh and any other non-RD/RDA
command is not allowed during MPR enable mode. The RESET function is supported during MPR enable mode.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
25
REV 1.1
08 / 2010
MR3 A[2]
MR3 A[1:0]
Function
MPR
MPR-Loc
0b
don't care (0b or 1b)
Normal operation, no MPR transaction.
All subsequent Reads will come from DRAM array.
All subsequent Write will go to DRAM array.
1b
See Table 13
Enable MPR mode, subsequent RD/RDA commands defined by MR3 A[1:0].
MPR Functional Description
•One bit wide logical interface via all DQ pins during READ operation.
•Register Read on x4:
•DQ[0] drives information from MPR.
•DQ[3:1] either drive the same information as DQ[0], or they drive 0b.
•Register Read on x8:
•DQ[0] drives information from MPR.
•DQ[7:1] either drive the same information as DQ[0], or they drive 0b.
•Register Read on x16:
•DQL[0] and DQU[0] drive information from MPR.
•DQL[7:1] and DQU[7:1] either drive the same information as DQL[0], or they drive 0b.
•Addressing during for Multi Purpose Register reads for all MPR agents:
•BA[2:0]: don‟t care
•A[1:0]: A[1:0] must be equal to „00‟b. Data read burst order in nibble is fixed
•A[2]: For BL=8, A[2] must be equal to 0b, burst order is fixed to [0,1,2,3,4,5,6,7], *) For Burst
Chop 4 cases, the burst order is switched on nibble base A[2]=0b, Burst order: 0,1,2,3 *)
A[2]=1b, Burst order: 4,5,6,7 *)
•A[9:3]: don‟t care
•A10/AP: don‟t care
•A12/BC: Selects burst chop mode on-the-fly, if enabled within MR0.
•A11, A13,... (if available): don‟t care
•Regular interface functionality during register reads:
•Support two Burst Ordering which are switched with A2 and A[1:0]=00b.
•Support of read burst chop (MRS and on-the-fly via A12/BC)
•All other address bits (remaining column address bits including A10, all bank address bits) will be ignored by the
DDR3 SDRAM.
•Regular read latencies and AC timings apply.
•DLL must be locked prior to MPR Reads.
NOTE: *) Burst order bit 0 is assigned to LSB and burst order bit 7 is assigned to MSB of the selected MPR agent.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
26
REV 1.1
08 / 2010
DDR3 SDRAM Command Description and Operation
Command Truth Table
Function
Abbreviation
CKE





A13
A12
A10
A0-9
NOTE
Previous
Cycle
Current
Cycle

A15

AP
A11
Mode Register Set
MRS
H
H
L
L
L
L
BA
OP Code
Refresh
REF
H
H
L
L
L
H
V
V
V
V
V
Self Refresh Entry
SRE
H
L
L
L
L
H
V
V
V
V
V
H
X
X
X
X
X
X
X
X
Self Refresh Exit
SRX
L
H
L
H
H
H
V
V
V
V
V
Single Bank Precharge
PRE
H
H
L
L
H
L
BA
V
V
L
V
Precharge all Banks
PREA
H
H
L
L
H
L
V
V
V
H
V
Bank Activate
ACT
H
H
L
L
H
H
BA
Row Address (RA)
Write (Fixed BL8 or BC4)
WR
H
H
L
H
L
L
BA
RFU
V
L
CA
Write (BC4, on the Fly)
WRS4
H
H
L
H
L
L
BA
RFU
L
L
CA
Write (BL8, on the Fly)
WRS8
H
H
L
H
L
L
BA
RFU
H
L
CA
Write with Auto Precharge (Fixed BL8 or BC4)
WRA
H
H
L
H
L
L
BA
RFU
V
H
CA
Write with Auto Precharge (BC4, on the Fly)
WRAS4
H
H
L
H
L
L
BA
RFU
L
H
CA
Write with Auto Precharge (BL8, on the Fly)
WRAS8
H
H
L
H
L
L
BA
RFU
H
H
CA
Read (Fixed BL8 or BC4)
RD
H
H
L
H
L
H
BA
RFU
V
L
CA
Read (BC4, on the Fly
RDS4
H
H
L
H
L
H
BA
RFU
L
L
CA
Read (BL8, on the Fly)
RDS8
H
H
L
H
L
H
BA
RFU
H
L
CA
Read with Auto Precharge (Fixed BL8 or BC4)
RDA
H
H
L
H
L
H
BA
RFU
V
H
CA
Read with Auto Precharge (BC4, on the Fly)
RDAS4
H
H
L
H
L
H
BA
RFU
L
H
CA
Read with Auto Precharge (BL8, on the Fly)
RDAS8
H
H
L
H
L
H
BA
RFU
H
H
CA
No Operation
NOP
H
H
L
H
H
H
V
V
V
V
V
Device Deselected
DES
H
H
H
X
X
X
X
X
X
X
X
Power Down Entry
PDE
H
L
L
H
H
H
V
V
V
V
V
H
X
X
X
X
X
X
X
X
Power Down Exit
PDX
L
H
L
H
H
H
V
V
V
V
V
H
X
X
X
X
X
X
X
X
ZQ Calibration Long
ZQCL
H
H
L
H
H
L
X
X
X
H
X
ZQ Calibration Short
ZQCS
H
H
L
H
H
L
X
X
X
L
X
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
27
REV 1.1
08 / 2010
DDR3 SDRAM Command Description and Operation
Command Truth Table (Conti.)
NOTE1. All DDR3 SDRAM commands are defined by states of , , ,  and CKE at the rising edge of the clock.
The MSB of BA, RA and CA are device density and configuration dependant.
NOTE2.  is Low enable command which will be used only for asynchronous reset so must be maintained HIGH
during any function.
NOTE3. Bank addresses (BA) determine which bank is to be operated upon. For (E)MRS BA selects an (Extended) Mode
Register.
NOTE4. “V” means “H or L (but a defined logic level)” and “X” means either “defined or undefined (like floating) logic level”.
NOTE5. Burst reads or writes cannot be terminated or interrupted and Fixed/on-the-Fly BL will be defined by MRS.
NOTE6. The Power-Down Mode does not perform any refresh operation.
NOTE7. The state of ODT does not affect the states described in this table. The ODT function is not available during Self
Refresh.
NOTE8. Self Refresh Exit is asynchronous.
NOTE9. VREF(Both VrefDQ and VrefCA) must be maintained during Self Refresh operation.
NOTE10. The No Operation command should be used in cases when the DDR3 SDRAM is in an idle or wait state. The
purpose of the No Operation command (NOP) is to prevent the DDR3 SDRAM from registering any unwanted
commands between operations. A No Operation command will not terminate a pervious operation that is still
executing, such as a burst read or write cycle.
NOTE11. The Deselect command performs the same function as No Operation command.
NOTE12. Refer to the CKE Truth Table for more detail with CKE transition.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
28
REV 1.1
08 / 2010
CKE Truth Table
Current State
CKE
Command (N)
, , , 
Action (N)
Notes
Previous Cycle
(N-1)
Current Cycle
(N)
Power-Down
L
L
X
Maintain Power-Down
L
H
DESELECT or NOP
Power-Down Exit
Self-Refresh
L
L
X
Maintain Self-Refresh
L
H
DESELECT or NOP
Self-Refresh Exit
Bank(s) Active
H
L
DESELECT or NOP
Active Power-Down Entry
Reading
H
L
DESELECT or NOP
Power-Down Entry
Writing
H
L
DESELECT or NOP
Power-Down Entry
Precharging
H
L
DESELECT or NOP
Power-Down Entry
Refreshing
H
L
DESELECT or NOP
Precharge Power-Down Entry
All Banks Idle
H
L
DESELECT or NOP
Precharge Power-Down Entry
H
L
REFRESH
Self-Refresh
NOTE 1 CKE (N) is the logic state of CKE at clock edge N; CKE (N-1) was the state of CKE at the previous clock edge.
NOTE 2 Current state is defined as the state of the DDR3 SDRAM immediately prior to clock edge N.
NOTE 3 COMMAND (N) is the command registered at clock edge N, and ACTION (N) is a result of COMMAND (N), ODT is
not included here.
NOTE 4 All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this document.
NOTE 5 The state of ODT does not affect the states described in this table. The ODT function is not available during
Self-Refresh.
NOTE 6 CKE must be registered with the same value on tCKEmin consecutive positive clock edges. CKE must remain at
the valid input level the entire time it takes to achieve the tCKEmin clocks of registrations. Thus, after any CKE
transition, CKE may not transition from its valid level during the time period of tIS + tCKEmin + tIH.
NOTE 7 DESELECT and NOP are defined in the Command Truth Table.
NOTE 8 On Self-Refresh Exit DESELECT or NOP commands must be issued on every clock edge occurring during the tXS
period. Read or ODT commands may be issued only after tXSDLL is satisfied.
NOTE 9 Self-Refresh modes can only be entered from the All Banks Idle state.
NOTE 10 Must be a legal command as defined in the Command Truth Table.
NOTE 11 Valid commands for Power-Down Entry and Exit are NOP and DESELECT only.
NOTE 12 Valid commands for Self-Refresh Exit are NOP and DESELECT only.
NOTE 13 Self-Refresh cannot be entered during Read or Write operations.
NOTE 14 The Power-Down does not perform any refresh operations.
NOTE 15“X” means “don‟t care“ (including floating around VREF) in Self-Refresh and Power-Down. It also applies to
Address pins.
NOTE 16 VREF (Both Vref_DQ and Vref_CA) must be maintained during Self-Refresh operation.
NOTE 17 If all banks are closed at the conclusion of the read, write or precharge command, then Precharge Power-Down is
entered, otherwise Active Power-Down is entered.
NOTE 18„Idle state‟ is defined as all banks are closed (tRP, tDAL, etc. satisfied), no data bursts are in progress, CKE is
high, and all timings from previous operations are satisfied (tMRD, tMOD, tRFC, tZQinit, tZQoper, tZQCS, etc.)
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
29
REV 1.1
08 / 2010
as well as all Self-Refresh exit and Power-Down Exit parameters are satisfied (tXS, tXP, tXPDLL, etc).
No Operation (NOP) Command
The No operation (NOP) command is used to instruct the selected DDR3 SDRAM to perform a NOP ( low and , ,
and  high). This prevents unwanted commands from being registered during idle or wait states. Operations already in
progress are not affected.
Deselect Command
The Deselect function ( HIGH) prevents new commands from being executed by the DDR3 SDRAM. The DDR3 SDRAM
is effectively deselected. Operations already in progress are not affected.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
30
REV 1.1
08 / 2010
DLL-off Mode
DDR3 DLL-off mode is entered by setting MR1 bit A0 to “1”; this will disable the DLL for subsequent operations until A0 bit
set back to “0”. The MR1 A0 bit for DLL control can be switched either during initialization or later.
The DLL-off Mode operations listed below are an optional feature for DDR3. The maximum clock frequency for DLL-off
Mode is specified by the parameter tCKDLL_OFF. There is no minimum frequency limit besides the need to satisfy the
refresh interval, tREFI.
Due to latency counter and timing restrictions, only one value of CAS Latency (CL) in MR0 and CAS Write Latency (CWL)
in MR2 are supported. The DLL-off mode is only required to support setting of both CL=6 and CWL=6.
DLL-off mode will affect the Read data Clock to Data Strobe relationship (tDQSCK) but not the data Strobe to Data
relationship (tDQSQ, tQH). Special attention is needed to line up Read data to controller time domain.
Comparing with DLL-on mode, where tDQSCK starts from the rising clock edge (AL+CL) cycles after the Read command,
the DLL-off mode tDQSCK starts (AL+CL-1) cycles after the read command. Another difference is that tDQSCK may not be
small compared to tCK (it might even be larger than tCK) and the difference between tDQSCKmin and tDQSCKmax is
significantly larger than in DLL-on mode.
The timing relations on DLL-off mode READ operation have shown at the following Timing Diagram (CL=6, BL=8)
DLL-off mode READ Timing Operation
Note: The tDQSCK is used here for DQS, DQS, and DQ to have a simplified diagram; the DLL_off shift will affect both
timings in the same way and the skew between all DQ, DQS, and  signals will still be tDQSQ.
CK
CK
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9
READ
CMD
Bank, Col b
Address
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
DQSdiff_DLL_on
DQ_DLL_on
DQSdiff_DLL_off
DQ_DLL_off
DQSdiff_DLL_off
DQ_DLL_off
RL = AL+CL = 6 (CL=6, AL=0)
RL(DLL_off) = AL+(CL-1) = 5 tDQSCKDLL_diff_min
tDQSCKDLL_diff_max
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
31
REV 1.1
08 / 2010
DLL on/off switching procedure
DDR3 DLL-off mode is entered by setting MR1 bit A0 to “1”; this will disable the DLL for subsequent operation until A0 bit
set back to “0”.
DLL “on” to DLL “off” Procedure
To switch from DLL “on” to DLL “off” requires the frequency to be changed during Self-Refresh outlined in the following
procedure:
1. Starting from Idle state (all banks pre-charged, all timing fulfilled, and DRAMs On-die Termination resistors, RTT,
must be in high impedance state before MRS to MR1 to disable the DLL).
2. Set MR1 Bit A0 to “1” to disable the DLL.
3. Wait tMOD.
4. Enter Self Refresh Mode; wait until (tCKSRE) satisfied.
5. Change frequency, in guidance with “Input Clock Frequency Change” section.
6. Wait until a stable clock is available for at least (tCKSRX) at DRAM inputs.
7. Starting with the Self Refresh Exit command, CKE must continuously be registered HIGH until all tMOD timings from
any MRS command are satisfied. In addition, if any ODT features were enabled in the mode registers when Self
Refresh mode was entered, the ODT signal must continuously be registered LOW until all tMOD timings from any
MRS command are satisfied. If both ODT features were disabled in the mode registers when Self Refresh mode was
entered, ODT signal can be registered LOW or HIGH.
8. Wait tXS, and then set Mode Registers with appropriate values (especially an update of CL, CWL, and WR may be
necessary. A ZQCL command may also be issued after tXS).
9. Wait for tMOD, and then DRAM is ready for next command.
DLL Switch Sequence from DLL-on to DLL-off
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
32
REV 1.1
08 / 2010
CK
CK
T0 T1 Ta0Ta1Tb0Tc0Td0Td1Te0Te1
MRS2)
1)
CMD
CKE
ODT
tMOD
Tf0
tCKSRE 4) tCKSRX 5) tXS tMOD
NOP SRE3) NOP SRX 6) NOP MRS7) NOP Valid8)
tCKESR
Valid8)
Valid 8)
Time
break Do not
Care
Note:
ODT: Static LOW in case RTT_Nom and RTT_WR is enabled, otherwise static Low or High
1) Starting with Idle State, RTT in Hi-Z State.
2) Disable DLL by setting MR1 Bit A0 to 1.
3) Enter SR.
4) Change Frequency.
5) Clock must be stable at least tCKSRX.
6) Exit SR.
7) Update Mode registers with DLL off parameters setting.
8) Any valid command.
DLL “off” to DLL “on” Procedure
To switch from DLL “off” to DLL “on” (with requires frequency change) during Self-Refresh:
1. Starting from Idle state (all banks pre-charged, all timings fulfilled and DRAMs On-die Termination resistors (RTT) must be
in high impedance state before Self-Refresh mode is entered).
2. Enter Self Refresh Mode, wait until tCKSRE satisfied.
3. Change frequency, in guidance with “Input clock frequency change” section.
4. Wait until a stable is available for at least (tCKSRX) at DRAM inputs.
5. Starting with the Self Refresh Exit command, CKE must continuously be registered HIGH until tDLLK timing from subse-
quent DLL Reset command is satisfied. In addition, if any ODT features were enabled in the mode registers when Self
Refresh mode was entered. the ODT signal must continuously be registered LOW until tDLLK timings from subsequent
DLL Reset command is satisfied. If both ODT features are disabled in the mode registers when Self Refresh mode was
entered, ODT signal can be registered LOW or HIGH.
6. Wait tXS, then set MR1 Bit A0 to “0” to enable the DLL.
7. Wait tMRD, then set MR0 Bit A8 to “1” to start DLL Reset.
8. Wait tMRD, then set Mode registers with appropriate values (especially an update of CL, CWL, and WR may be necessary.
After tMOD satisfied from any proceeding MRS command, a ZQCL command may also be issued during or after tDLLK).
9. Wait for tMOD, then DRAM is ready for next command (remember to wait tDLLK after DLL Reset before applying command
requiring a locked DLL!). In addition, wait also for tZQoper in case a ZQCL command was issued.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
33
REV 1.1
08 / 2010
CK
CK
T0 Ta0Ta1Tb0Tc0Tc1Td0Te0Tf1Tg0
1)
CMD
CKE
ODT
Th0
tCKSRE tCKSRX 4) tXS tMRD tDLLK
NOP SRE2) SRX5) MRS6) MRS7) MRS8) Valid
ODTLoff
+ 1tck 3) tMRD
Valid
tCKESR
Time
break Do not
Care
NOP
Note:
ODT: Static LOW in case RTT_Nom and RTT_WR is enabled, otherwise static Low or High
1) Starting from Idle State.
2) Enter SR.
3) Change Frequency.
4) Clock must be stable at least tCKSRX.
5) Exit SR.
6) Set DLL-on by MR1 A0="0"
7) Start DLL Reset
8) Any valid command
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
34
REV 1.1
08 / 2010
Input Clock frequency change
Once the DDR3 SDRAM is initialized, the DDR3 SDRAM requires the clock to be “stable” during almost all states of normal
operation. This means once the clock frequency has been set and is to be in the “stable state”, the clock period is not
allowed to deviate except for what is allowed for by the clock jitter and SSC (spread spectrum clocking) specification.
The input clock frequency can be changed from one stable clock rate to another stable clock rate under two conditions: (1)
Self-Refresh mode and (2) Precharge Power-Down mode. Outside of these two modes, it is illegal to change the clock
frequency.
For the first condition, once the DDR3 SDRAM has been successfully placed in to Self-Refresh mode and tCKSRE has
been satisfied, the state of the clock becomes a don‟t care. Once a don‟t care, changing the clock frequency is permissible,
provided the new clock frequency is stable prior to tCKSRX. When entering and exiting Self-Refresh mode of the sole
purpose of changing the clock frequency. The DDR3 SDRAM input clock frequency is allowed to change only within the
minimum and maximum operating frequency specified for the particular speed grade.
The second condition is when the DDR3 SDRAM is in Precharge Power-Down mode (either fast exit mode or slow exit
mode). If the RTT_Nom feature was enabled in the mode register prior to entering Precharge power down mode, the ODT
signal must continuously be registered LOW ensuring RTT is in an off state. If the RTT_Nom feature was disabled in the
mode register prior to entering Precharge power down mode, RTT will remain in the off state. The ODT signal can be
registered either LOW or HIGH in this case. A minimum of tCKSRE must occur after CKE goes LOW before the clock
frequency may change. The DDR3 SDRAM input clock frequency is allowed to change only within the minimum and
maximum operating frequency specified for the particular speed grade. During the input clock frequency change, ODT and
CKE must be held at stable LOW levels. Once the input clock frequency is changed, stable new clocks must be provided to
the DRAM tCKSRX before precharge Power Down may be exited; after Precharge Power Down is exited and tXP has
expired, the DLL must be RESET via MRS. Depending on the new clock frequency additional MRS commands may need to
be issued to appropriately set the WR, CL, and CWL with CKE continuously registered high. During DLL re-lock period,
ODT must remain LOW and CKE must remain HIGH. After the DLL lock time, the DRAM is ready to operate with new clock
frequency.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
35
REV 1.1
08 / 2010
Change Frequency during Precharge Power-down
CK
CK
T0 T1 T2 Ta0Tb0Tc0Tc1Td0Td1Te0
CKE
Command
DQS,
DQS
tCH tCL
tCK
Te1
tIH tIS tIH tIS
tCKSRE
tCKE
tCKSRX
tCHb tCLb
tCKb
NOP NOP NOP NOP NOP MRS NOP Valid
DLL
Reset Valid
tIH tIS
Address
ODT
DQ
DM
High-Z
High-Z
tAOFPD/tAOF
tCPDED
tXP
tDLLK
Previous Clock Frequency New Clock Frequency
Frequency
Change
Enter Precharge
Power-Down mode Exit Precharge
Power-Down mode
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
36
REV 1.1
08 / 2010
Write Leveling
For better signal integrity, DDR3 memory adopted fly by topology for the commands, addresses, control signals, and clocks.
The fly by topology has benefits from reducing number of stubs and their length but in other aspect, causes flight time skew
between clock and strobe at every DRAM on DIMM. It makes it difficult for the Controller to maintain tDQSS, tDSS, and
tDSH specification. Therefore, the controller should support “write leveling” in DDR3 SDRAM to compensate the skew.
The memory controller can use the “write leveling” feature and feedback from the DDR3 SDRAM to adjust the DQS - 
to CK -  relationship. The memory controller involved in the leveling must have adjustable delay setting on DQS -  to
align the rising edge of DQS -  with that of the clock at the DRAM pin. DRAM asynchronously feeds back CK - ,
sampled with the rising edge of DQS - , through the DQ bus. The controller repeatedly delays DQS -  until a
transition from 0 to 1 is detected. The DQS -  delay established though this exercise would ensure tDQSS specification.
Besides tDQSS, tDSS, and tDSH specification also needs to be fulfilled. One way to achieve this is to combine the actual
tDQSS in the application with an appropriate duty cycle and jitter on the DQS-  signals. Depending on the actual
tDQSS in the application, the actual values for tDQSL and tDQSH may have to be better than the absolute limits provided in
“AC Timing Parameters” section in order to satisfy tDSS and tDSH specification. A conceptual timing of this scheme is
show as below figure.
0or 1 0 0
Diff _CK
Diff _DQS
Source
Diff _CK
Diff _ DQS
Destination
DQ
DQ
Push DQS to capture
0 -1 transition
0or 1 1 1
DQS/ driven by the controller during leveling mode must be determined by the DRAM based on ranks populated.
Similarly, the DQ bus driven by the DRAM must also be terminated at the controller.
One or more data bits should carry the leveling feedback to the controller across the DRAM configurations x4, and x8.
Therefore, a separate feedback mechanism should be able for each byte lane. The upper data bits should provide the
feedback of the upper diff_DQS (diff_UDQS) to clock relationship whereas the lower data bits would indicate the lower
diff_DQS (diff_LDQS) to clock relationship.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
37
REV 1.1
08 / 2010
DRAM setting for write leveling and DRAM termination unction in that mode
DRAM enters into Write leveling mode if A7 in MR1 set “High” and after finishing leveling, DRAM exits from write leveling
mode if A7 in MR1 set “Low”. Note that in write leveling mode, only DQS/ terminations are activated and deactivated
via ODT pin not like normal operation.
MR setting involved in the leveling procedure
Function
MR1
Enable
Disable
Write leveling enable
A7
1
0
Output buffer mode (Qoff)
A12
0
1
DRAM termination function in the leveling mode
ODT pin at DRAM
DQS/DQS termination
DQs termination
De-asserted
off
off
Asserted
on
off
Note: In write leveling mode with its output buffer disabled (MR1[bit7]=1 with MR1[bit12]=1) all RTT_Nom settings are
allowed; in Write Leveling Mode with its output buffer enabled (MR1[bit7]=1 with MR1[bit12]=0) only RTT_Nom settings of
RZQ/2, RZQ/4, and RZQ/6 are allowed.
Procedure Description
Memory controller initiates Leveling mode of all DRAMs by setting bit 7 of MR1 to 1. With entering write leveling mode, the
DQ pins are in undefined driving mode. During write leveling mode, only NOP or Deselect commands are allowed. As well
as an MRS command to exit write leveling mode. Since the controller levels one rank at a time, the output of other rank
must be disabled by setting MR1 bit A12 to 1. Controller may assert ODT after tMOD, time at which DRAM is ready to
accept the ODT signal.
Controller may drive DQS low and  high after a delay of tWLDQSEN, at which time DRAM has applied on-die
termination on these signals. After tDQSL and tWLMRD controller provides a single DQS,  edge which is used by the
DRAM to sample CK  driven from controller. tWLMRD(max) timing is controller dependent.
DRAM samples CK - status with rising edge of DQS and provides feedback on all the DQ bits asynchronously after
tWLO timing. There is a DQ output uncertainty of tWLOE defined to allow mismatch on DQ bits; there are no read strobes
(DQS/DQS) needed for these DQs. Controller samples incoming DQ and decides to increment or decrement DQS 
delay setting and launches the next DQS/ pulse after some time, which is controller dependent. Once a 0 to 1 transition
is detected, the controller locks DQS  delay setting and write leveling is achieved for the device. The following figure
describes the timing diagram and parameters for the overall Write leveling procedure.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
38
REV 1.1
08 / 2010
Timing details of Write leveling sequence
DQS -  is capturing CK -  low at T1 and CK -  high at T2
NOP NOP NOP NOP NOP NOP NOP NOP NOP
CK
CK
CMD
ODT
Diff_DQS
Prime DQ
Late
Rema ining
DQs
tMOD
tWLMRD tWLO
tWLS tWLH
tWLOE
tWLS tWLH
tWLO
NOPMRS
tDQSHtDQSLtDQSHtDQSL
T1 T2
Time
break Do not
Care
One Prime DQ:
Early
Rema ining
DQs
tWLO
tWLO
Undefined
Driving Mode
tWLOEtWLO
tWLO
All DQs are Prime:
Late
Rema ining
DQs
Early
Rema ining
DQs
tWLMRD tWLO
tWLO
tWLOE
tWLDQSEN
NOP
Note:
1. DRAM has the option to drive leveling feedback on a prime DQ or all DQs. If feedback is driven only on
one DQ, the remaining DQs must be driven low as shown in above Figure, and maintained at this state
through out the leveling procedure.
2. MRS: Load MR1 to enter write leveling mode
3. NOP: NOP or deselect
4. diff_DQS is the differential data strobe (DQS, ). Timing reference points are the zero crossings. DQS
is shown with solid line,  is shown with dotted line.
6. DQS/ needs to fulfill minimum pulse width requirements tDQSH(min) and tDQSL(min) as defined for
regular Writes; the max pulse width is system dependent.
Write Leveling Mode Exit
The following sequence describes how Write Leveling Mode should be exited:
1. After the last rising strobe edge (see ~T0), stop driving the strobe signals (see ~Tc0). Note: From now on, DQ pins
are in undefined driving mode, and will remain undefined, until tMOD after the respective MR command (Te1).
2. Drive ODT pin low (tIS must be satisfied) and keep it low (see Tb0).
3. After the RTT is switched off, disable Write Level Mode via MRS command (see Tc2).
4. After tMOD is satisfied (Te1), any valid command may be registered. (MR commands may be issued after tMRD
(Td1).
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
39
REV 1.1
08 / 2010
Timing detail of Write Leveling exit
CK
CK
T0 T1 Ta0Tc0Tc1Tc2Td1Te1
CMD
BA
tIS
tMOD
tMRD
ODT
RTT_DQS_DQS
DQS_DQS
Result = 1
tWLO
DQ
RTT_Nom
Td0Te0T2 Tb0
tAOFmin
tAOFmax
TransitioningTime Break Do not Care Undefined
Driving Mode
NOP NOP NOP NOP NOP NOP NOP MRS NOP Valid NOP Valid
MR1 Valid Valid
tODTLoff
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
40
REV 1.1
08 / 2010
Extended Temperature Usage
a. Auto Self-refresh supported
b. Extended Temperature Range supported
c. Double refresh required for operation in the Extended Temperature Range.
Mode Register Description
Field
Bits
Description
ASR
MR2(A6)
Auto Self-Refresh (ASR)
When enabled, DDR3 SDRAM automatically provides Self-Refresh power management functions
for all supported operating temperature values. If not enabled, the SRT bit must be programmed to
indicate TOPER during subsequent Self-Refresh operation.
0 = Manual SR Reference (SRT)
1 = ASR enable
SRT
MR2(A7)
Self-Refresh Temperature (SRT) Range
If ASR = 0, the SRT bit must be programmed to indicate TOPER during subsequent Self-Refresh
operation. If ASR = 1, SRT bit must be set to 0.
0 = Normal operating temperature range
1 = Extended operating temperature range
Auto Self-Refresh mode - ASR mode
DDR3 SDRAM provides an Auto-Refresh mode (ASR) for application ease. ASR mode is enabled by setting MR2 bit A6=1
and MR2 bit A7=0. The DRAM will manage Self-Refresh entry in either the Normal or Extended Temperature Ranges. In
this mode, the DRAM will also manage Self-Refresh power consumption when the DRAM operating temperature changes,
lower at low temperatures and higher at high temperatures. If the ASR option is not supported by DRAM, MR2 bit A6 must
set to 0. If the ASR option is not enabled (MR2 bit A6=0), the SRT bit (MR2 bit A7) must be manually programmed with the
operating temperature range required during Self-Refresh operation. Support of the ASR option does not automatically
imply support of the Extended Temperature Range.
Self-Refresh Temperature Range - SRT
SRT applies to devices supporting Extended Temperature Range only. If ASR=0, the Self-Refresh Temperature (SRT)
Range bit must be programmed to guarantee proper self-refresh operation. If SRT=0, then the DRAM will set an
appropriate refresh rate for Self-Refresh operation in the Normal Temperature Range. If SRT=1, then the DRAM will set an
appropriate, potentially different, refresh rate to allow Self-Refresh operation in either the Normal or Extended Temperature
Ranges. The value of the SRT bit can effect self-refresh power consumption, please refer to IDD table for details.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
41
REV 1.1
08 / 2010
Self-Refresh mode summary
MR2
A[6]
MR2
A[7]
Self-Refresh operation
Allowed Operating Temperature
Range for Self-Refresh mode
0
0
Self-Refresh rate appropriate for the Normal Temperature Range
Normal (0 ~ 85C)
0
1
Self-Refresh appropriate for either the Normal or Extended Temperature Ranges. The DRAM must support Extended
Temperature Range. The value of the SRT bit can effect self-refresh power consumption, please refer to the IDD table
for details.
Normal and Extended (0 ~ 95C)
1
0
ASR enabled (for devices supporting ASR and Normal Temperature Range). Self-Refresh power consumption is
temperature dependent.
Normal (0 ~ 85C)
1
0
ASR enabled (for devices supporting ASR and Extended Temperature Range). Self-Refresh power consumption is
temperature dependent.
Normal and Extended (0 ~ 95C)
1
1
Illegal
MPR MR3 Register Definition
MR3
A[2]
MR3
A[1:0]
Function
0
don't care
(0 or 1)
Normal operation, no MPR transaction.
All subsequent Reads will come from DRAM array.
All subsequent Writes will go to DRAM array.
1
See the following table
Enable MPR mode, subsequent RD/RDA commands defined by MR3 A[1:0].
MPR Functional Description
One bit wide logical interface via all DQ pins during READ operation.
Register Read on x4:
DQ [0] drives information from MPR.
DQ [3:1] either drive the same information as DQ [0], or they drive 0.
Register Read on x8:
DQ [0] drives information from MPR.
DQ [7:1] either drive the same information as DQ [0], or they drive 0.
Addressing during for Multi Purpose Register reads for all MPR agents:
BA [2:0]: don‟t care.
A [1:0]: A [1:0] must be equal to “00”. Data read burst order in nibble is fixed.
A[2]: For BL=8, A[2] must be equal to 0, burst order is fixed to [0,1,2,3,4,5,6,7]; For Burst chop 4 cases, the burst order is
switched on nibble base, A[2]=0, burst order: 0,1,2,3, A[2]=1, burst order: 4,5,6,7. *)
A [9:3]: don‟t care.
A10/AP: don‟t care.
A12/BC: Selects burst chop mode on-the-fly, if enabled within MR0
A11, A13: don‟t care.
Regular interface functionality during register reads:
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
42
REV 1.1
08 / 2010
Support two Burst Ordering which are switched with A2 and A[1:0]=00.
Support of read burst chop (MRS and on-the-fly via A12/BC).
All other address bits (remaining column addresses bits including A10, all bank address bits) will be ignored by the DDR3
SDRAM.
Regular read latencies and AC timings apply.
DLL must be locked prior to MPR READs.
Note *): Burst order bit 0 is assigned to LSB and burst order bit 7 is assigned to MSB of the selected MPR agent.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
43
REV 1.1
08 / 2010
MPR Register Address Definition
The following table provide an overview of the available data location, how they are addressed by MR3 A[1:0] during a MRS
to MR3, and how their individual bits are mapped into the burst order bits during a Multi Purpose Register Read.
MPR MR3 Register Definition
MR3
A[2]
MR3
A[1:0]
Function
Burst Length
Read Address
A[2:0]
Burst Order and Data Pattern
1
00
Read Predefined Pattern
for System Calibration
BL8
000
Burst order 0,1,2,3,4,5,6,7
Pre-defined Data Pattern [0,1,0,1,0,1,0,1]
BC4
000
Burst order 0,1,2,3
Pre-defined Data Pattern [0,1,0,1]
BC4
100
Burst order 4,5,6,7
Pre-defined Data Pattern [0,1,0,1]
1
01
RFU
BL8
000
Burst order 0,1,2,3,4,5,6,7
BC4
000
Burst order 0,1,2,3
BC4
100
Burst order 4,5,6,7
1
10
RFU
BL8
000
Burst order 0,1,2,3,4,5,6,7
BC4
000
Burst order 0,1,2,3
BC4
100
Burst order 4,5,6,7
1
11
RFU
BL8
000
Burst order 0,1,2,3,4,5,6,7
BC4
000
Burst order 0,1,2,3
BC4
100
Burst order 4,5,6,7
Note: Burst order bit 0 is assigned to LSB and the burst order bit 7 is assigned to MSB of the selected MPR agent.
ACTIVE Command
The ACTIVE command is used to open (or activate) a row in a particular bank for subsequent access. The value on the
BA0-BA2 inputs selects the bank, and the addresses provided on inputs A0-A13 selects the row. These rows remain active
(or open) for accesses until a precharge command is issued to that bank. A PRECHARGE command must be issued before
opening a different row in the same bank.
PRECHARGE Command
The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The
bank(s) will be available for a subsequent row activation a specified time (tRP) after the PRECHARGE command is issued,
except in the case of concurrent auto precharge, where a READ or WRITE command to a different bank is allowed as long
as it does not interrupt the data transfer in the current bank and does not violate any other timing parameters. Once a bank
has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to
that bank. A PRECHARGE command is allowed if there is no open row in that bank (idle bank) or if the previously open row
is already in the process of precharging. However, the precharge period will be determined by the last PRECHARGE
command issued to the bank.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
44
REV 1.1
08 / 2010
READ Operation
Read Burst Operation
During a READ or WRITE command DDR3 will support BC4 and BL8 on the fly using address A12 during the READ or
WRITE (AUTO PRECHARGE can be enabled or disabled).
A12=0, BC4 (BC4 = burst chop, tCCD=4)
A12=1, BL8
A12 will be used only for burst length control, not a column address.
Read Burst Operation RL=5 (AL=0, CL=5, BL=8)
READ Burst Operation RL = 9 (AL=4, CL=5, BL=8)
READ Timing Definitions
Read timing is shown in the following figure and is applied when the DLL is enabled and locked.
Rising data strobe edge parameters:
tDQSCK min/max describes the allowed range for a rising data strobe edge relative to CK, CK.
tDQSCK is the actual position of a rising strobe edge relative to CK, CK.
tQSH describes the DQS,  differential output high time.
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
Falling data strobe edge parameters:
tQSL describes the DQS,  differential output low time.
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
CK
CK
T0 T1 T3 T5 T6 T7 T9 T145
CL=5
DQS, DQS
T2 T4 T8 T10
READ NOPCMD NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Bank
Col n
Address
Dout
nDout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5 Dout
n +6 Dout
n +7
DQ
RL = AL + CL
tRPRE tRPST
CK
CK
T0 T1 T3 T5 T6 T7 T9 T145
CL=5
DQS, DQS
T2 T4 T8 T10
READ NOPCMD NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Bank
Col n
Address
Dout
nDout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
DQ RL = AL + CL
tRPREAL = 4
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
45
REV 1.1
08 / 2010
Read Timing Definition
Read Timing; Clock to Data Strobe relationship
Clock to Data Strobe relationship is shown in the following figure and is applied when the DLL is enabled and locked.
Rising data strobe edge parameters:
tDQSCK min/max describes the allowed range for a rising data strobe edge relative to CK and .
tDQSCK is the actual position of a rising strobe edge relative to CK and .
tQSH describes the data strobe high pulse width.
Falling data strobe edge parameters:
tDSL describes the data strobe low pulse width
Rising Strobe
Region
tDQSK, min tDQSK, max
tDQSK
CK
CK
DQS
DQS
tDQSK
Rising Strobe
Region
tQSH tQSL
tQH tQH
tDQSQ tDQSQ
Associated
DQ pins
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
46
REV 1.1
08 / 2010
Clock to Data Strobe Relationship
CK
CK
RL Measured
to this point
DQS, DQS
Early Strobe
DQS, DQS
Late Strobe
tLZ(DQS)min
tLZ(DQS)max
tRPRE
tRPRE
tDQSCKmin
tDQSCKmax
tQSH tQSL tRPST
tRPST
tHZ(DQS)min
tHZ(DQS)max
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
47
REV 1.1
08 / 2010
Read Timing; Data Strobe to Data Relationship
The Data Strobe to Data relationship is shown in the following figure and is applied when the DLL and enabled and locked.
Rising data strobe edge parameters:
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
Falling data strobe edge parameters:
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
Data Strobe to Data Relationship
Dout
n +6 Dout
n +7
tRPST
CK
CK
T0 T1 T3 T5 T6 T7 T9
DQS, DQS
T2 T4 T8
READ NOPCMD NOP NOP NOP NOP NOP NOP NOP NOP
Bank
Col n
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
DQ (Last data valid) RL = AL + CL
tRPRE
Dout
n +6 Dout
n +7
Dout
nDout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
tLZ(DQ)min
Valid data
tHZ(DQ)min
tDQSQmax
Valid data
tQH
tQH
Dout
n
tDQSQmin
DQ (First data no
longer valid)
All DQ collectively
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
48
REV 1.1
08 / 2010
Read to Read (CL=5, AL=0)
T11T10
NOP NOP
Dout
n +6 Dout
n +7
tRPST
CK
CK
T0 T1 T3 T5 T6 T7 T9
T2 T4 T8
NOPCMD NOP NOP READ NOP NOP NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
tCCD tRPRE
Dout
n
T12
NOP
T13
NOP
RL = 5
Bank
Col b
READ
Dout
b +6 Dout
b +7
Dout
b +1 Dout
b +2 Dout
b +3 Dout
b +4 Dout
b +5
Dout
b
RL = 5
DQS, DQS
DQ
READ (BL8) to READ (BL8)
NOP NOP
tRPST
NOPCMD NOP NOP READ NOP NOP NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
tCCD tRPRE
Dout
n
NOP NOP
RL = 5
Bank
Col b
READ
Dout
b +1 Dout
b +2 Dout
b +3
Dout
b
RL = 5
DQS, DQS
DQ
READ (BL4) to READ (BL4)
tRPRE
tRPST
READ
Bank
Col n
READ
Bank
Col n
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
49
REV 1.1
08 / 2010
READ to WRITE (CL=5, AL=0; CWL=5, AL=0)
T11T10
NOP
Dout
n +6 Dout
n +7
tWPST
CK
CK
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
NOPCMD NOP NOP WRITE
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
READ to Write Command delay = RL +tCCD + 2tCK -WL
tRPRE
Dout
n
T12
NOP
T13
NOP
RL = 5
Bank
Col b
Dout
b +7
Dout
b +1 Dout
b +2 Dout
b +3 Dout
b +4 Dout
b +5
WL = 5
DQS, DQS
DQ
READ (BL8) to WRITE (BL8)
NOP
tWPST
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
READ to WRITE Command Delay = RL + tCCD/2 + 2tCK - WL tRPRE
Dout
n
NOP NOP
RL = 5
READ
Dout
b +1 Dout
b +2 Dout
b +3
WL = 5
DQS, DQS
READ (BL4) to WRITE (BL4)
tWPRE
tRPST
T14 T15
NOP NOP
tWRPRE
tRPST
Bank
Col n
READ NOP NOP NOP
NOPNOPNOP
DQ
NOP NOP
tBL = 4 clocks
tWR
tWTR
READ
Bank
Col n
WRITE
Bank
Col b
NOP
Dout
b
NOPNOPNOP NOP
Dout
bDout
b +6
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
50
REV 1.1
08 / 2010
READ to READ (CL=5, AL=0)
T11T10
NOP NOP
Dout
n +6 Dout
n +7
tRPST
CK
CK
T0 T1 T3 T5 T6 T7 T9
T2 T4 T8
NOPCMD NOP NOP NOP NOP NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
tCCD tRPRE
Dout
n
T12
NOP
T13
NOP
RL = 5
READ
Dout
b +1 Dout
b +2 Dout
b +3
Dout
b
RL = 5
DQS, DQS
DQ
READ (BL8) to READ (BC4)
NOP NOP
tRPST
NOPCMD NOP NOP NOP NOP NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
tCCD tRPRE
Dout
n
NOP NOP
RL = 5
READ
RL = 5
DQS, DQS
READ (BC4) to READ (BL8)
tRPRE
tRPST
DQ
READ
Bank
Col n
READ
Bank
Col n
READ
Bank
Col b
READ
Bank
Col b
Dout
b +6 Dout
b +7
Dout
b +1 Dout
b +2 Dout
b +3 Dout
b +4 Dout
b +5
Dout
b
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
51
REV 1.1
08 / 2010
READ to WRITE (CL=5, AL=0; CWL=5, AL=0)
T11T10
NOP NOP
Dout
n +6 Dout
n +7
tRPST
CK
CK
T0 T1 T3 T5 T6 T7 T9
T2 T4 T8
NOPCMD NOP NOP WRITE
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +4 Dout
n +5
tRPRE
Dout
n
T12
NOP
T13
NOP
RL = 5
READ
Dout
b +1 Dout
b +2 Dout
b +3
WL = 5
DQS, DQS
DQ
NOP NOP
tWPST
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
READ to WRITE Command delay = RL + tCCD/2 +2tCK - WL tRPRE
Dout
n
NOP NOP
RL = 5
READ
WL = 5
DQS, DQS
READ (BL4) to WRITE (BL8)
tWPRE
tRPST
DQ
READ
Bank
Col n
READ
Bank
Col n
NOP
Bank
Col b
WRITE
Bank
Col b
Dout
b +6 Dout
b +7
Dout
b +1 Dout
b +2 Dout
b +3 Dout
b +4 Dout
b +5
Dout
b
NOPNOPNOPNOP
READ (BL8) to WRITE (BC4)
NOP NOP NOPNOP
tWPST
tWPRE
Dout
b
READ to WRITE Command delay = RL + tCCD +2tCK - WL
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
52
REV 1.1
08 / 2010
Write Operation
DDR3 Burst Operation
During a READ or WRITE command, DDR3 will support BC4 and BL8 on the fly using address A12 during the READ or
WRITE (Auto Precharge can be enabled or disabled).
A12=0, BC4 (BC4 = Burst Chop, tCCD=4)
A12=1, BL8
A12 is used only for burst length control, not as a column address.
WRITE Timing Violations
Motivation
Generally, if timing parameters are violated, a complete reset/initialization procedure has to be initiated to make sure the
DRAM works properly. However, it is desirable for certain minor violations that the DRAM is guaranteed not to “hang up”
and errors be limited to that particular operation.
For the following, it will be assumed that there are no timing violations w.r.t. to the Write command itself (including ODT,
etc.) and that it does satisfy all timing requirements not mentioned below.
Data Setup and Hold Violations
Should the strobe timing requirements (tDS, tDH) be violated, for any of the strobe edges associated with a write burst, then
wrong data might be written to the memory location addressed with the offending WRITE command.
Subsequent reads from that location might result in unpredictable read data, however, the DRAM will work properly
otherwise.
Strobe to Strobe and Strobe to Clock Violations
Should the strobe timing requirements (tDQSH, tDQSL, tWPRE, tWPST) or the strobe to clock timing requirements (tDSS,
tDSH, tDQSS) be violated, for any of the strobe edges associated with a Write burst, then wrong data might be written to
the memory location addressed with the offending WRITE command. Subsequent reads from that location might result in
unpredictable read data, however the DRAM will work properly otherwise.
Write Timing Parameters
This drawing is for example only to enumerate the strobe edges that “belong” to a write burst. No actual timing violations
are shown here. For a valid burst all timing parameters for each edge of a burst need to be satisfied (not only for one edge -
as shown).
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
53
REV 1.1
08 / 2010
Write Timing Definition
Note:
1. BL=8, WL=5 (AL=0, CWL=5).
2. Din n = data in from column n.
3. NOP commands are shown for ease of illustration; other command may be valid at these times.
4. BL8 setting activated by either MR0 [A1:0=00] or MR0 [A1:0=01] and A12 = 1 during WRITE command at T0.
4. tDQSS must be met at each rising clock edge.
Tn
CK
CK
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
NOPCMD NOP NOP
Address
DQ
NOP
WL = AL + CWL
NOP NOP
Din
n +6 Din
n +7
Din
n +1 Din
n +2 Din
n +3 Din
n +4 Din
n +5
Din
n
tDQSS tDSH
tDQSL
tDSS
tWPST(min)
tDQSL(min)
tDSS
tDSS tDSS
tDSS
DQ
tDSH
tDQSH tDQSL
tDSS
tDQSH
tWPRE(min)
tDSS
tDSH
tDQSH
tDSH
tDSH
tDSS tDSS
tDSS
DQ Din
n +6 Din
n +7
Din
n +1 Din
n +2 Din
n +3 Din
n +4 Din
n +5
Din
n
tDSH
tDQSH tDQSH
tDSH
tDQSH
tDSHtDSH
NOP
tDQSH
tWPRE(min)
Write
Bank
Col n
tWPRE(min)
tDQSH
NOP
tDSS
tDQSL tDSS tDSS
NOP
tDSH
tDSH
Din
n +6 Din
n +7
Din
n +1 Din
n +2 Din
n +3 Din
n +4 Din
n +5
Din
n
tDQSH
tDSH
NOP
tDSS
tDSS
tDQSL(min)
tWPST(min)
tDQSL(min)
tWPST(min)
tDQSS
DQS, DQS
(tDQSS min)
DQS, DQS
(tDQSS nominal)
DQS, DQS
(tDQSS max)
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
54
REV 1.1
08 / 2010
WRITE to WRITE (WL=5; CWL=5, AL=0)
T11T10
NOP
Dout
n +7
CK
CK
T0 T1 T3 T5 T6 T7 T9
T2 T4 T8
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +5
tCCD tWPRE
T12
NOP
T13
NOP
WL = 5
Dout
b +6 Dout
b +7
Dout
b +1 Dout
b +2 Dout
b +3 Dout
b +5
WL = 5
DQS, DQS
DQ
WRITE (BL8) to WRITE (BL8)
NOP
tWPST
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
tCCD tRPRE
NOP NOP
WL = 5
READ
Dout
b +1 Dout
b +2 Dout
b +3
WL = 5
DQS, DQS
WRITE (BC4) to WRITE (BC4)
tWPRE
tWPST
tWPST
Bank
Col n
WRITE NOP NOP NOP
NOPNOPWRITE
DQ
WRITE
Bank
Col n
WRITE
Bank
Col b
NOP
Bank
Col b
Dout
n
NOP NOP NOP NOP
Dout
n +4 Dout
n +6 Dout
bDout
b +4
tBL=4
tWR
tWTR
tBL=4
tWR
tWTR
Dout
nDout
b
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
55
REV 1.1
08 / 2010
WRITE to READ (RL=5, CL=5, AL=0; WL=5, CWL=5, AL=0; BL=4)
T11T10
NOP
Dout
n +7
CK
CK
T0 T1 T3 T5 T6 T7 T9
T2 T4 T8
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +5
tWPRE
T12
NOP
T13
READ
WL = 5
DQS, DQS
DQ
WRITE (BL8) to READ (BC4/BL8)
NOP
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
tRPRE
Dout
n
NOP READ
WL = 5
DQS, DQS
WRITE (BC4) to READ (BC4/BL8)
tWPST
Bank
Col n
WRITE NOP NOP NOP
NOPNOPNOP
DQ
WRITE
Bank
Col n
NOP NOP
Bank
Col b
Dout
n
NOP NOP NOP NOP
Dout
n +4 Dout
n +6
tWTR
RL=5
tBL=4
tWPST
Bank
Col b
tWTR
RL=5
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
56
REV 1.1
08 / 2010
WRITE to WRITE (WL=5, CWL=5, AL=0)
T11T10
NOP
Dout
n +7
CK
CK
T0 T1 T3 T5 T6 T7 T9
T2 T4 T8
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3 Dout
n +5
tCCD tWPRE
T12
NOP
T13
NOP
WL = 5
Dout
b +1 Dout
b +2
WL = 5
DQS, DQS
DQ
WRITE (BL8) to WRITE (BC4)
NOP
tWPST
NOPCMD NOP NOP NOP
Address
Dout
n +1 Dout
n +2 Dout
n +3
tCCD tRPRE
Dout
n
NOP NOP
WL = 5
READ
Dout
b +1 Dout
b +2 Dout
b +3
WL = 5
DQS, DQS
WRITE (BC4) to WRITE (BL8)
tWPRE
tWPST
tWPST
Bank
Col n
WRITE NOP NOP NOP
NOPNOPWRITE
DQ
WRITE
Bank
Col n
WRITE
Bank
Col b
NOP
Bank
Col b
Dout
n
NOP NOP NOP NOP
Dout
n +4 Dout
n +6 Dout
b
tBL=4
tWR
tWTR
tBL=4
tWR
tWTR
Dout
b +3
Dout
b +6 Dout
b +7
Dout
b +3 Dout
b +5
Dout
b +4
Dout
b
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
57
REV 1.1
08 / 2010
Refresh Command
The Refresh command (REF) is used during normal operation of the DDR3 SDRAMs. This command is not persistent, so it
must be issued each time a refresh is required. The DDR3 SDRAM requires Refresh cycles at an average periodic interval
of tREFI. When , , and  are held Low and WE High at the rising edge of the clock, the chip enters a Refresh
cycle. All banks of the SDRAM must be precharged and idle for a minimum of the precharge time tRP(min) before the
Refresh Command can be applied. The refresh addressing is generated by the internal refresh controller. This makes the
address bits “Don‟t Care” during a Refresh command. An internal address counter suppliers the address during the refresh
cycle. No control of the external address bus is required once this cycle has started. When the refresh cycle has completed,
all banks of the SDRAM will be in the precharged (idle) state. A delay between the Refresh Command and the next valid
command, except NOP or DES, must be greater than or equal to the minimum Refresh cycle time tRFC(min) as shown in
the following figure.
In general, a Refresh command needs to be issued to the DDR3 SDRAM regularly every tREFI interval. To allow for
improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided.
A maximum of 8 Refresh commands can be postponed during operation of the DDR3 SDRAM, meaning that at no point in
time more than a total of 8 Refresh commands are allowed to be postponed. In case that 8 Refresh commands are
postponed in a row, the resulting maximum interval between the surrounding Refresh commands is limited to 9 x tREFI. A
maximum of 8 additional Refresh commands can be issued in advance (“pulled in”), with each one reducing the number of
regular Refresh commands required later by one. Note that pulling in more than 8 Refresh commands in advance does not
further reduce the number of regular Refresh commands required later, so that the resulting maximum interval between two
surrounding Refresh command is limited to 9 x tREFI. Before entering Self-Refresh Mode, all postponed Refresh
commands must be executed.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
58
REV 1.1
08 / 2010
Self-Refresh Entry/Exit Timing
Postponing Refresh Commands (Example)
Pulled-in Refresh Commands (Example)
CK
CK
T0 T1 Ta0Tb0Tb1Tb3Ta1Tb2
NOPCMD NOP REF Valid
NOPREF NOP Valid ValidValid Valid REF
Tc0Tc1
Valid
tRFC tRFC(min)
tREFI (max, 9 x tREFI)
DRAM must be idle
DRAM must be idle
Time Break
9 x tREFI
tREFI
tREFI
8 REF-Command postponed
t
9 x tREFI
tREFI
t
tREFI
8 REF-Commands pulled-in
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
59
REV 1.1
08 / 2010
Self-Refresh Operation
The Self-Refresh command can be used to retain data in the DDR3 SDRAM, even if the reset of the system is powered
down. When in the Self-Refresh mode, the DDR3 SDRAM retains data without external clocking. The DDR3 SDRAM
device has a built-in timer to accommodate Self-Refresh operation. The Self-Refresh Entry (SRE) Command is defined by
having , , , and  held low with WE high at the rising edge of the clock.
Before issuing the Self-Refreshing-Entry command, the DDR3 SDRAM must be idle with all bank precharge state with tRP
satisfied. Also, on-die termination must be turned off before issuing Self-Refresh-Entry command, by either registering ODT
pin low “ODTL + 0.5tCK” prior to the Self-Refresh Entry command or using MRS to MR1 command. Once the Self-Refresh
Entry command is registered, CKE must be held low to keep the device in Self-Refresh mode. During normal operation
(DLL on), MR1 (A0=0), the DLL is automatically disabled upon entering Self-Refresh and is automatically enabled
(including a DLL-RESET) upon exiting Self-Refresh.
When the DDR3 SDRAM has entered Self-Refresh mode, all of the external control signals, except CKE and , are
“don‟t care”. For proper Self-Refresh operation, all power supply and reference pins (VDD, VDDQ, VSS, VSSQ, VRefCA,
and VRefDQ) must be at valid levels. The DRAM initiates a minimum of one Refresh command internally within tCKE
period once it enters Self-Refresh mode.
The clock is internally disabled during Self-Refresh operation to save power. The minimum time that the DDR3 SDRAM
must remain in Self-Refresh mode is tCKE. The user may change the external clock frequency or halt the external clock
tCKSRE after Self-Refresh entry is registered; however, the clock must be restarted and stable tCKSRX before the device
can exit Self-Refresh mode.
The procedure for exiting Self-Refresh requires a sequence of events. First, the clock must be stable prior to CKE going
back HIGH. Once a Self-Refresh Exit Command (SRX, combination of CKE going high and either NOP or Deselect on
command bus) is registered, a delay of at least tXS must be satisfied before a valid command not requiring a locked DLL
can be issued to the device to allow for any internal refresh in progress. Before a command which requires a locked DLL
can be applied, a delay of at least tXSDLL and applicable ZQCAL function requirements [TBD] must be satisfied.
Before a command that requires a locked DLL can be applied, a delay of at least tXSDLL must be satisfied. Depending on
the system environment and the amount of time spent in Self-Refresh, ZQ calibration commands may be required to
compensate for the voltage and temperature drift as described in “ZQ Calibration Commands”. To issue ZQ calibration
commands, applicable timing requirements must be satisfied.
CKE must remain HIGH for the entire Self-Refresh exit period tXSDLL for proper operation except for Self-Refresh re-entry.
Upon exit from Self-Refresh, the DDR3 SDRAM can be put back into Self-Refresh mode after waiting at least tXS period
and issuing one refresh command (refresh period of tRFC). NOP or deselect commands must be registered on each
positive clock edge during the Self-Refresh exit interval tXS. ODT must be turned off during tXSDLL.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
60
REV 1.1
08 / 2010
The use of Self-Refresh mode instructs the possibility that an internally times refresh event can be missed when CKE is
raised for exit from Self-Refresh mode. Upon exit from Self-Refresh, the DDR3 SDRAM requires a minimum of one extra
refresh command before it is put back into Self-Refresh mode.
Self-Refresh Entry/Exit Timing
CK, CK
T1 T2 Ta0Tb0Tc0Tc1Te0Tf
ODTL
tCKSRE
tCKSRX
tCPDED
tRF
SRE NOP Valid 2)
tCKESR
tXSDLL
tXS
CMD
ODT
Note:
1. Only NOP or DES commands
2. Valid commands not requiring a locked DLL
3. Valid commands requiring a locked DLL
T0 Td0
Valid
CKE
NOP SRX NOP 1) Valid 3)
Valid Valid
Valid
Valid
Enter Self Refresh Exit Self Refresh
Do Not
Care Time
Break
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
61
REV 1.1
08 / 2010
Power-Down Modes
Power-Down Entry and Exit
Power-Down is synchronously entered when CKE is registered low (along with NOP or Deselect command). CKE is not
allowed to go low while mode register set command, MPR operations, ZQCAL operations, DLL locking or read/write
operation are in progress. CKE is allowed to go low while any of other operation such as row activation, precharge or auto
precharge and refresh are in progress, but power-down IDD spec will not be applied until finishing those operation.
The DLL should be in a locked state when power-down is entered for fastest power-down exit timing. If the DLL is not
locked during power-down entry, the DLL must be reset after exiting power-down mode for proper read operation and
synchronous ODT operation. DRAM design provides all AC and DC timing and voltage specification as well proper DLL
operation with any CKE intensive operations as long as DRAM controller complies with DRAM specifications.
During Power-Down, if all banks are closed after any in progress commands are completed, the device will be in precharge
Power-Down mode; if any bank is open after in progress commands are completed, the device will be in active
Power-Down mode.
Entering Power-down deactivates the input and output buffers, excluding CK, CK, ODT, , and . To protect
DRAM internal delay on CKE line to block the input signals, multiple NOP or Deselect commands are needed during the
CKE switch off and cycle(s) after, this timing period are defined as tCPDED. CKE_low will result in deactivation of
command and address receivers after tCPDED has expired.
Power-Down Entry Definitions
Status of DRAM
MRS bit A12
DLL
PD Exit
Relevant Parameters
Active
(A Bank or more open)
Don't Care
On
Fast
tXP to any valid command.
Precharged
(All Banks Precharged)
0
Off
Slow
tXP to any valid command. Since it is in precharge state, commands
here will be ACT, AR, MRS/EMRS, PR, or PRA.
tXPDLL to commands who need DLL to operate, such as RD, RDA,
or ODT control line.
Precharged
(All Banks Precharged)
1
On
Fast
tXP to any valid command.
Also the DLL is disabled upon entering precharge power-down (Slow Exit Mode), but the DLL is kept enabled during
precharge power-down (Fast Exit Mode) or active power-down. In power-down mode, CKE low,  high, and a stable
clock signal must be maintained at the inputs of the DDR3 SDRAM, and ODT should be in a valid state but all other input
signals are “Don‟t care” (If  goes low during Power-Down, the DRAM will be out of PD mode and into reset state).
CKE low must be maintain until tCKE has been satisfied. Power-down duration is limited by 9 times tREFI of the device.
The power-down state is synchronously exited when CKE is registered high (along with a NOP or Deselect command).
CKE high must be maintained until tCKE has been satisfied. A valid, executable command can be applied with power-down
exit latency, tXP and/or tXPDLL after CKE goes high. Power-down exit latency is defined at AC spec table of this datasheet.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
62
REV 1.1
08 / 2010
Active Power-Down Entry and Exit timing diagram
Timing Diagrams for CKE with PD Entry, PD Exit with Read, READ with Auto Precharge, Write and Write with Auto
Precharge, Activate, Precharge, Refresh, MRS:
Power-Down Entry after Read and Read with Auto Precharge
Power-Down Entry after Write with Auto Precharge
T0 T1 T2 Ta0Ta1Tb0Tb1Tc0
CK
CK
Valid NOP NOP NOP NOP NOP NOPCMD
CKE Valid Valid
tIS
tIH
tPD tIH
tIS tCKE
Address Valid Valid
tCPDED
Enter
Power-Down Exit
Power-Down
tXP
Do not
care Time
Break
T0 T1 Ta0Ta1Ta2Ta3Ta4Ta5
CK
CK
RD or
RDA NOP NOP NOP NOP NOP NOPCMD
CKE
Address Valid Valid
Power-Down
Entry Do not
care Time
Break
Ta6Ta7Ta8Tb0Tb1
NOP NOP NOP NOP NOP Valid
Valid
tIS tCPDED
DQS
RL = AL + CL
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
Din
bDin
b+1 Din
b+2 Din
b+3
tRDPDEN
BL8
BC4
tPD
T0 T1 Ta0Ta1Ta2Ta3Ta4Ta5
CK
CK
WRITE NOP NOP NOP NOP NOP NOPCMD
CKE
Address Bank,
Col n
Power-Down
Entry Do not
care Time
Break
Ta6Ta7Tb0Tb1Tb2
NOP NOP NOP NOP NOP NOP
tIS tCPDED
DQS
WL=AL+CWL
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
Din
bDin
b+1 Din
b+2 Din
b+3
tWRAPDEN
BL8
BC4
WR (1)
Tb3
NOP
Tc0
Valid
tPD
Start Internal
Precharge
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
63
REV 1.1
08 / 2010
Power-Down Entry after Write
Precharge Power-Down (Fast Exit Mode) Entry and Exit
Precharge Power-Down (Slow Exit Mode) Entry and Exit
Refresh Command to Power-Down Entry
T0 T1 Ta0Ta1Ta2Ta3Ta4Ta5
CK
CK
WRITE NOP NOP NOP NOP NOP NOPCMD
CKE
Address Bank,
Col n
Power-Down
Entry Do not
care Time
Break
Ta6Ta7Tb0Tb1Tb2
NOP NOP NOP NOP NOP NOP
tIS tCPDED
DQS
WL=AL+CWL
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
Din
bDin
b+1 Din
b+2 Din
b+3
tWRPDEN
BL8
BC4
Tc0
NOP
tPDWR
T0 T1 T2 Ta0Ta1Tb0Tb1Tc0
CK
CK
WRITE NOP NOP NOP NOP NOP NOPCMD
CKE
Do not
care Time
Break
NOP
tIS tCPDED tIH tCKE
tIS
tXP
NOP Valid
tPD
Enter
Power-Down
Mode
Exit
Power-Down
Mode
T0 T1 T2 Ta0Ta1Tb0Tb1Tc0
CK
CK
WRITE NOP NOP NOP NOP NOP ValidCMD
CKE
Do not
care Time
Break
NOP
tIS tCPDED tIH tCKE
tIS tXP
NOP Valid
tPD
Enter
Power-Down
Mode
Exit
Power-Down
Mode
Td0
Valid
tXPDLL
Valid
T0 T1 T2 T3 Ta0Ta1
CK
CK
REF NOP NOP ValidCMD
CKE
Do not
care Time
Break
NOP
tIS tCPDED
Valid
tPD
Valid Valid
tREFPDEN
Address
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
64
REV 1.1
08 / 2010
Active Command to Power-Down Entry
Precharge/Precharge all Command to Power-Down Entry
MRS Command to Power-Down Entry
T0 T1 T2 T3 Ta0Ta1
CK
CK
Active NOP NOP ValidCMD
CKE
Do not
care Time
Break
NOP
tIS tCPDED
Valid
tPD
Valid Valid
tACTPDEN
Address
T0 T1 T2 T3 Ta0Ta1
CK
CK
PRE
PREA NOP NOP ValidCMD
CKE
Do not
care Time
Break
NOP
tIS tCPDED
Valid
tPD
Valid Valid
tPREPDEN
Address
T0 T1 Ta0Ta1Tb0Tb1
CK
CK
NOP NOP ValidCMD
CKE
Do not
care Time
Break
NOP
tIS tCPDED
Valid
tPD
Valid
tMRSPDEN
Address
MRS
Valid
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
65
REV 1.1
08 / 2010
On-Die Termination (ODT)
ODT (On-Die Termination) is a feature of the DDR3 SDRAM that allows the DRAM to turn on/off termination resistance for
each DQ, DQS, , and DM for x4 and x8 configuration and TDQS,  for x8 configuration, when enabled via A11=1
in MR1) via the ODT control pin. The ODT feature is designed to improve signal integrity of the memory channel by allowing
the DRAM controller to independently turn on/off termination resistance for any or all DRAM devices.
The ODT feature is turned off and not supported in Self-Refresh mode.
A simple functional representation of the DRAM ODT feature is shown as below.
The switch is enabled by the internal ODT control logic, which uses the external ODT pin and other control information. The
value of RTT is determined by the settings of Mode Register bits. The ODT pin will be ignored if the Mode Register MR1
and MR2 are programmed to disable ODT and in self-refresh mode.
ODT Mode Register and ODT Truth Table
The ODT Mode is enabled if either of MR1 {A2, A6, A9} or MR2 {A9, A10} are non-zero. In this case, the value of RTT is
determined by the settings of those bits.
Application: Controller sends WR command together with ODT asserted.
One possible application: The rank that is being written to provides termination.
DRAM turns ON termination if it sees ODT asserted (except ODT is disabled by MR)
DRAM does not use any write or read command decode information.
To other
circuitry
like
RCV, ...
VDDQ
/ 2
RTT
Switch DQ , DQS, DM, TDQS
ODT
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
66
REV 1.1
08 / 2010
Termination Truth Table
ODT pin
DRAM Termination State
0
OFF
1
ON, (OFF, if disabled by MR1 {A2, A6, A9} and MR2{A9, A10} in general)
Synchronous ODT Mode
Synchronous ODT mode is selected whenever the DLL is turned on and locked. Based on the power-down definition, these
modes are:
Any bank active with CKE high
Refresh with CKE high
Idle mode with CKE high
Active power down mode (regardless of MR0 bit A12)
Precharge power down mode if DLL is enabled during precharge power down by MR0 bit A12
The direct ODT feature is not supported during DLL-off mode. The on-die termination resistors must be disabled by continu-
ously registering the ODT pin low and/or by programming the RTT_Nom bits MR1{A9,A6,A2} to {0,0,0} via a mode register
set command during DLL-off mode.
In synchronous ODT mode, RTT will be turned on ODTLon clock cycles after ODT is sampled high by a rising clock edge
and turned off ODTLoff clock cycles after ODT is registered low by a rising clock edge. The ODT latency is tied to the write
latency (WL) by: ODTLonn = WL - 2; ODTLoff = WL-2.
ODT Latency and Posted ODT
In synchronous ODT Mode, the Additive Latency (AL) programmed into the Mode Register (MR1) also applies to the ODT
signal. The DRAM internal ODT signal is delayed for a number of clock cycles defined by the Additive Latency (AL) relative
to the external ODT signal. ODTLon = CWL + AL - 2; ODTLoff = CWL + AL - 2. For details, refer to DDR3 SDRAM latency
definitions.
ODT Latency
Symbol
Parameter
DDR3 SDRAM
Unit
ODTLon
ODT turn on Latency
WL - 2 = CWL + AL - 2
tCK
ODTLoff
ODT turn off Latency
WL - 2 = CWL + AL - 2
tCK
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
67
REV 1.1
08 / 2010
Timing Parameters
In synchronous ODT mode, the following timing parameters apply: ODTLon, ODTLoff, tAON min/max, AOF min/max.
Minimum RTT turn-on time (tAON min) is the point in time when the device leaves high impedance and ODT resistance
begins to turn on. Maximum RTT turn-on time (tAON max) is the point in time when the ODT resistance is fully on. Both are
measured from ODTLon.
Minimum RTT turn-off time (tAOF min) is the point in time when the device starts to turn off the ODT resistance. Maximum
RTT turn off time (tAOF max) is the point in time when the on-die termination has reached high impedance. Both are
measured from ODTLoff.
When ODT is asserted, it must remain high until ODTH4 is satisfied. If a Write command is registered by the SDRAM with
ODT high, then ODT must remain high until ODTH4 (BL=4) or ODTH8 (BL=8) after the write command. ODTH4 and
ODTH8 are measured from ODT registered high to ODT registered low or from the registration of a write command until
ODT is registered low.
Synchronous ODT Timing Example for AL=3; CWL=5; ODTLon=AL+CWL-2=6;
ODTLoff=AL+CWL-2=6
Synchronous ODT example with BL=4, WL=7
ODT must be held for at least ODTH4 after assertion (T1); ODT must be kept high ODTH4 (BL=4) or ODTH8 (BL=8) after
Write command (T7). ODTH is measured from ODT first registered high to ODT first registered low, or from registration of
Write command with ODT high to ODT registered low. Note that although ODTH4 is satisfied from ODT registered at T6
ODT must not go low before T11 as ODTH4 must also be satisfied from the registration of the Write command at T7.
CK
CK
AL=3
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8 T12
ODT
ODTH4, min
ODTLon = CWL + AL -2 ODTLoff = CWL + AL -2
T13 T14 T15
CWL - 2
DRAM_RTT
tAONmin
tAONmax tAONmin
tAONmax
RTT_NOM
AL=3
Transitioning Do not care
CKE
CK
CK
ODTH4
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8 T12
ODT
ODTLon = CWL -2
T13 T14 T15
ODTLoff = WL - 2
DRAM_RTT
tAONmin tAONmax
tAOFmax
RTT_NOM
T16 T17 T18
ODTH4min
ODTH4
ODTLoff = CWL -2
ODTLon = CWL -2
tAOFmin
tAOFmax tAONmax
tAONmin tAOFmin
NOP NOP NOP NOP NOP NOP NOP WRS4NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Transitioning Do not care
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
68
REV 1.1
08 / 2010
ODT during Reads:
As the DDR3 SDRAM cannot terminate and drive at the same time, RTT must be disabled at least half a clock cycle before
the read preamble by driving the ODT pin low appropriately. RTT may not be enabled until the end of the post-amble as
shown in the following figure. DRAM turns on the termination when it stops driving which is determined by tHZ. If DRAM
stops driving early (i.e. tHZ is early), then tAONmin time may apply. If DRAM stops driving late (i.e. tHZ is late), then DRAM
complies with tAONmax timing. Note that ODT may be disabled earlier before the Read and enabled later after the Read
than shown in this example.
ODT must be disabled externally during Reads by driving ODT low. (Example: CL=6;
AL=CL-1=5; RL=AL+CL=11; CWL=5; ODTLon=CWL+AL-2=8; ODTLoff=CWL+AL-2=8)
CK
CK
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8 T12 T13 T14 T15 T16
CMD
Address
RL = AL + CL
RTT_NOMRTT
ODTLoff = CWL + AL - 2
tAOFmax
tAOFmin
ODTLon = CWL + AL - 2
RTT_NOM
tAONmax
ODT
DRAM
ODT
DQSdiff
Din
bDin
b+1 Din
b+2 Din
b+3 Din
b+4 Din
b+5 Din
b+6 Din
b+7
DQ
Read NOP NOP NOP NOP NOP NOPNOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Valid
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
69
REV 1.1
08 / 2010
Dynamic ODT
In certain application cases and to further enhance signal integrity on the data bus, it is desirable that the termination
strength of the DDR3 SDRAM can be changed without issuing an MRS command. This requirement is supported by the
“Dynamic ODT” feature as described as follows:
Functional Description
The Dynamic ODT Mode is enabled if bit (A9) or (A10) of MR2 is set to „1‟. The function is described as follows:
Two RTT values are available: RTT_Nom and RTT_WR.
The value for RTT_Nom is preselected via bits A[9,6,2] in MR1.
The value for RTT_WR is preselected via bits A[10,9] in MR2.
During operation without write commands, the termination is controlled as follows:
Nominal termination strength RTT_Nom is selected.
Termination on/off timing is controlled via ODT pin and latencies ODTLon and ODTLoff.
When a Write command (WR, WRA, WRS4, WRS8, WRAS4, WRAS8) is registered, and if Dynamic ODT is enabled, the
termination is controlled as follows:
A latency ODTLcnw after the write command, termination strength RTT_WR is selected.
A latency ODTLcwn8 (for BL8, fixed by MRS or selected OTF) or ODTLcwn4 (for BC4, fixed by MRS or selected OTF) after
the write command, termination strength RTT_Nom is selected.
Termination on/off timing is controlled via ODT pin and ODTLon, ODTLoff.
The following table shows latencies and timing parameters which are relevant for the on-die termination control in Dynamic
ODT mode.
The dynamic ODT feature is not supported at DLL-off mode. User must use MRS command to set RTT_WR, MR2[A10,A9
= [0,0], to disable Dynamic ODT externally.
When ODT is asserted, it must remain high until ODTH4 is satisfied. If a Write command is registered by the SDRAM with
ODT high, then ODT must remain high until ODTH4 (BL=4) or ODTH8 (BL=8) after the Write command. ODTH4 and
ODTH8 are measured from ODT registered high to ODT registered low or from the registration of Write command until ODT
is register low.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
70
REV 1.1
08 / 2010
Latencies and timing parameters relevant for Dynamic ODT
Name and Description
Abbr.
Defined from
Defined to
Definition for all DDR3 speed pin
Unit
ODT turn-on Latency
ODTLon
registering external ODT signal high
turning termination on
ODTLon=WL-2
tCK
ODT turn-off Latency
ODTLoff
registering external ODT signal low
turning termination off
ODTLoff=WL-2
tCK
ODT Latency for changing from
RTT_Nom to RTT_WR
ODTLcnw
registering external write command
change RTT strength from
RTT_Nom to RTT_WR
ODTLcnw=WL-2
tCK
ODT Latency for change from
RTT_WR to RTT_Nom (BL=4)
ODTLcwn4
registering external write command
change RTT strength from
RTT_WR to RTT_Nom
ODTLcwn4=4+ODTLoff
tCK
ODT Latency for change from
RTT_WR to RTT_Nom (BL=8)
ODTLcwn8
registering external write command
change RTT strength from
RTT_WR to RTT_Nom
ODTLcwn8=6+ODTLoff
tCK(avg)
Minimum ODT high time
after ODT assertion
ODTH4
registering ODT high
ODT registered low
ODTH4=4
tCK(avg)
Minimum ODT high time
after Write (BL=4)
ODTH4
registering write with ODT high
ODT registered low
ODTH4=4
tCK(avg)
Minimum ODT high time
after Write (BL=8)
ODTH8
registering write with ODT high
ODT register low
ODTH8=6
tCK(avg)
RTT change skew
tADC
ODTLcnw
ODTLcwn
RTT valid
tADC(min)=0.3tCK(avg)
tADC(max)=0.7tCK(avg)
tCK(avg)
Note: tAOF,nom and tADC,nom are 0.5tCK (effectively adding half a clock cycle to ODTLoff, ODTcnw, and ODTLcwn)
ODT Timing Diagrams
Dynamic ODT: Behavior with ODT being asserted before and after the write
Note: Example for BC4 (via MRS or OTF), AL=0, CWL=5. ODTH4 applies to first registering ODT high and to the
registration of the Write command. In this example ODTH4 would be satisfied if ODT went low at T8. (4 clocks after the
Write command).
CK
CK
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8 T12 T13 T14 T15 T16
CMD
ODT
RTT
DQS/DQS
DQ
ODTLon
ODTLcwn4
T17
ODTLcnw
tAONmin
tAONmax
tADCmin
tADCmax
WL
tADCmin
tADCmax
tAOFmin
tAOFmax
Address
RTT_WR
Din
nDin
n+1 Din
n+2 Din
n+3
ODTH4ODTLoff
NOP NOP NOP NOP WRS4 NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Valid
ODTH4
RTT_Nom
Do not
care Transitioning
RTT_Nom
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
71
REV 1.1
08 / 2010
Dynamic ODT: Behavior without write command, AL=0, CWL=5
Note: ODTH4 is defined from ODT registered high to ODT registered low, so in this example ODTH4 is satisfied; ODT
registered low at T5 would also be legal.
Dynamic ODT: Behavior with ODT pin being asserted together with write
command for the duration of 6 clock cycles.
Note: Example for BL8 (via MRS or OTF), AL=0, CWL=5. In this example ODTH8=6 is exactly satisfied.
tADCmax
CK
CK
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
CMD
ODT
RTT
DQS/DQS
DQ
ODTLon
ODTLoff
tAONmin
tAONmax
tADCmin
RTT_Nom
Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid Valid
Address
ODTH4 ODTLoff
Do not
care Transitioning
tAOFmax
tAOFmin
CK
CK
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
CMD
ODT
RTT
DQS/DQS
DQ
ODTH8
ODTLon
ODTLcnw
tAONmin
tAONmax
ODTLoff
WL
RTT_WR
NOP WRS8 NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Valid
Din
hDin
h+1 Din
h+2 Din
h+3 Din
h+4 Din
h+5 Din
h+6 Din
h+7
ODTLcwn8
Do not
care Transitioning
Address
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
72
REV 1.1
08 / 2010
Dynamic ODT: Behavior with ODT pin being asserted together with write command
for a duration of 6 clock cycles, example for BC4 (via MRS or OTF), AL=0, CWL=5.
Dynamic ODT: Behavior with ODT pin being asserted together with write command
for the duration of 4 clock cycles.
CK
CK#
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
ODT
RTT
DQS/DQS
DQ
ODTLon
RTT_WR
ODTLcnw
tAONmin tAOFmin
tAOFmax
tAONmax
ODTLoff
WL
ODTH4
ODTLcwn4
CMD NOP WRS4 NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Valid
Address
Din
nDin
n+1 Din
n+2 Din
n+3
Do not
care Transitioning
CK
CK
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
ODT
RTT
DQS/DQS
DQ
ODTLon
RTT_WR RTT_Nom
ODTLcnw
tAONmin tADCmin
tADCmax
tAOFmin
tAOFmax
tAONmax
ODTLoff
WL
ODTH4
ODTLcwn4
CMD NOP WRS4 NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
Valid
Address
Din
nDin
n+1 Din
n+2 Din
n+3
Do not
care Transitioning
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
73
REV 1.1
08 / 2010
Asynchronous ODT Mode
Asynchronous ODT mode is selected when DRAM runs in DLLon mode, but DLL is temporarily disabled (i.e. frozen) in
precharge power-down (by MR0 bit A12). Based on the power down mode definitions, this is currently Precharge power
down mode if DLL is disabled during precharge power down by MR0 bit A12.
In asynchronous ODT timing mode, internal ODT command is NOT delayed by Additive Latency (AL) relative to the
external ODT command.
In asynchronous ODT mode, the following timing parameters apply: tAONPD min/max, tAOFPD min/max.
Minimum RTT turn-on time (tAONPD min) is the point in time when the device termination circuit leaves high impedance
state and ODT resistance begins to turn on. Maximum RTT turn on time (tAONPD max) is the point in time when the ODT
resistance is fully on.
tAONPDmin and tAONPDmax are measured from ODT being sampled high.
Minimum RTT turn-off time (tAOFPDmin) is the point in time when the devices termination circuit starts to turn off the ODT
resistance. Maximum ODT turn off time (tAOFPDmax) is the point in time when the on-die termination has reached high
impedance. tAOFPDmin and tAOFPDmax are measured from ODT being sample low.
Asynchronous ODT Timings on DDR3 SDRAM with fast ODT transition: AL is ignored.
In Precharge Power Down, ODT receiver remains active, however no Read or Write command can be issued, as the
respective ADD/CMD receivers may be disabled.
Asynchronous ODT Timing Parameters for all Speed Bins
Symbol
Description
min
max
Unit
tAONPD
Asynchronous RTT turn-on delay (Power-Down with DLL frozen)
1
9
ns
tAOFPD
Asynchronous RTT turn-off delay (Power-Down with DLL frozen)
1
9
ns
ODT timing parameters for Power Down (with DLL frozen) entry and exit transition
period
Description
min
max
ODT to RTT
turn-on delay
min{ ODTLon * tCK + tAONmin; tAONPDmin }
min{ (WL - 2) * tCK + tAONmin; tAONPDmin }
max{ ODTLon * tCK + tAONmax; tAONPDmax }
max{ (WL - 2) * tCK + tAONmax; tAONPFmax }
ODT to RTT
turn-off delay
min{ ODTLoff * tCK + tAOFmin; tAOFPDmin }
min{ (WL - 2) * tCK + tAOFmin; tAOFPDmin }
max{ ODTLoff * tCK + tAOFmax; tAOFPDmax }
max{ (WL - 2) * tCK + tAOFmax; tAOFPDmax }
tANPD
WL-1
CK
CK#
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8
ODT
RTT
tAONPDmin
CKE
tIH
tIS
T12 T13 T14 T15
tAONPDmax tAOFPDmin
tAOFPDmax
tIH
tIS
Do not
care Transitioning
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
74
REV 1.1
08 / 2010
Synchronous to Asynchronous ODT Mode Transition during Power-Down Entry
If DLL is selected to be frozen in Precharge Power Down Mode by the setting of bit A12 in MR0 to “0”, there is a transition
period around power down entry, where the DDR3 SDRAM may show either synchronous or asynchronous ODT behavior.
The transition period is defined by the parameters tANPD and tCPDED(min). tANPD is equal to (WL-1) and is counted
backwards in time from the clock cycle where CKE is first registered low. tCPDED(min) starts with the clock cycle where
CKE is first registered low. The transition period begins with the starting point of tANPD and terminates at the end point of
tCPDED(min). If there is a Refresh command in progress while CKE goes low, then the transition period ends at the later
one of tRFC(min) after the Refresh command and the end point of tCPDED(min). Please note that the actual starting point
at tANPD is excluded from the transition period, and the actual end point at tCPDED(min) and tRFC(min, respectively, are
included in the transition period.
ODT assertion during the transition period may result in an RTT changes as early as the smaller of tAONPDmin and
(ODTLon*tck+tAONmin) and as late as the larger of tAONPDmax and (ODTLon*tCK+tAONmax). ODT de-assertion during
the transition period may result in an RTT change as early as the smaller of tAOFPDmin and (ODTLoff*tCK+tAOFmin) and
as late as the larger of tAOFPDmax and (ODTLoff*tCK+tAOFmax). Note that, if AL has a large value, the range where RTT
is uncertain becomes quite large. The following figure shows the three different cases: ODT_A, synchronous behavior
before tANPD; ODT_B has a state change during the transition period; ODT_C shows a state change after the transition
period.
Synchronous to asynchronous transition during Precharge Power Down (with DLL
frozen) entry (AL=0; CWL=5; tANPD=WL-1=4)
CK
CK
CKE
CMD
Last sync.
ODT
tANPD
RTT
Sync. Or
async. ODT
ODTLoff tAOFmax
tAOFmin
tAOFPDmin
tAOFPDmax
ODTLoff+tAOFPDmin
ODTLoff+tAOFPDmax
RTT
tAOFPDmin
First async.
ODT
RTT
NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12
PD entry transition period
Do not
care Time
Break
Transitioning
tCPDEDmin
tCPDED
NOP
RTT
RTT
RTT
tAOFPDmax
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
75
REV 1.1
08 / 2010
Asynchronous to Synchronous ODT Mode transition during Power-Down Exit
If DLL is selected to be frozen in Precharge Power Down Mode by the setting of bit A12 in MR0 to “0”, there is also a
transition period around power down exit, where either synchronous or asynchronous response to a change in ODT must
be expected from the DDR3 SDRAM.
This transition period starts tANPD before CKE is first registered high, and ends tXPDLL after CKE is first registered high.
tANPD is equal to (WL -1) and is counted (backwards) from the clock cycle where CKE is first registered high.
ODT assertion during the transition period may result in an RTT change as early as the smaller of tAONPDmin and (ODT-
Lon*tCK+tAONmin) and as late as the larger of tAONPDmax and (ODTLon*tCK+tAONmax). ODT de-assertion during the
transition period may result in an RTT change as early as the smaller of tAOFPDmin and (ODTLoff*tCK+tAOFmin) and as
late as the larger of tAOFPDmax and (ODToff*tCK+tAOFmax). Note that if AL has a large value, the range where RTT is
uncertain becomes quite large. The following figure shows the three different cases: ODT_C, asynchronous response
before tANPD; ODT_B has a state change of ODT during the transition period; ODT_A shows a state change of ODT after
the transition period with synchronous response.
Asynchronous to synchronous transition during Precharge Power Down (with DLL
frozen) exit (CL=6; AL=CL-1; CWL=5; tANPD=WL-1=9)
CK
CK
ODT_C
_sync
DRAM
_RTT_
C_sync
ODT_B
_tran
tAOFPDmax
tAOFPDmin
DRAM
_RTT_
B_tran
ODT_A
_async
DRAM_
RTT_A_
async
T0 T1 T2 Ta0Ta1Ta2Ta3Ta4Ta5Ta6Tb0Tb1Tb2Tc0Tc1Tc2Td0
Do not
care Time
Break
Transitioning
Td1
CMD NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
CKE
NOP
tXPDLL
PD exit transition period
RTT
RTT
tAOFPDmin
ODTLoff + tAOFmax
ODTLoff + tAOFmin
tAOFPDmax
tANPD
NOP
tAOFmax
RTT
ODTLoff
tAOFmin
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
76
REV 1.1
08 / 2010
Asynchronous to Synchronous ODT Mode during short CKE high and short CKE low
periods
If the total time in Precharge Power Down state or Idle state is very short, the transition periods for PD entry and PD exit
may overlap. In this case, the response of the DDR3 SDRAMs RTT to a change in ODT state at the input may be
synchronous or asynchronous from the state of the PD entry transition period to the end of the PD exit transition period
(even if the entry ends later than the exit period).
If the total time in Idle state is very short, the transition periods for PD exit and PD entry may overlap. In this case, the
response of the DDR3 SDRAMs RTT to a change in ODT state at the input may be synchronous or asynchronous from the
state of the PD exit transition period to the end of the PD entry transition period. Note that in the following figure, it is
assumed that there was no Refresh command in progress when Idle state was entered.
Transition period for short CKE cycles with entry and exit period overlapping
(AL=0; WL=5; tANPD=WL-1=4)
CK
CK
T11T10
T0 T1 T3 T5 T6 T7 T9T2 T4 T8 T12 T13 T14
tANPD
Do not
care Transitioning
CKE
CMD REF NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP NOP
PD exit transition period
tANPD tXPDLL
PD entry transition period
tRFC(min)
CKE
Short CKE high transition period tXPDLL
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
77
REV 1.1
08 / 2010
ZQ Calibration Commands
ZQ Calibration Description
ZQ Calibration command is used to calibrate DRAM Ron and ODT values. DDR3 SDRAM needs longer time to calibrate
output driver and on-die termination circuits at initialization and relatively smaller time to perform periodic calibrations.
ZQCL command is used to perform the initial calibration during power-up initialization sequence. This command may be
issued at any time by the controller depending on the system environment. ZQCL command triggers the calibration engine
inside the DRAM and once calibration is achieved the calibrated values are transferred from calibration engine to DRAM IO
which gets reflected as updated output driver and on-die termination values.
The first ZQCL command issued after reset is allowed a timing period of tZQinit to perform the full calibration and the
transfer of values. All other ZQCL commands except the first ZQCL command issued after RESET is allowed a timing
period of tZQoper.
ZQCS command is used to perform periodic calibrations to account for voltage and temperature variations. A shorter timing
window is provided to perform the calibration and transfer of values as defined by timing parameter tZQCS.
No other activities should be performed on the DRAM channel by the controller for the duration of tZQinit, tZQoper, or
tZQCS. The quiet time on the DRAM channel allows calibration of output driver and on-die termination values. Once DRAM
calibration is achieved, the DRAM should disable ZQ current consumption path to reduce power.
All banks must be precharged and tRP met before ZQCL or ZQCS commands are issued by the controller.
ZQ calibration commands can also be issued in parallel to DLL lock time when coming out of self refresh. Upon self-refresh
exit, DDR3 SDRAM will not perform an IO calibration without an explicit ZQ calibration command. The earliest possible time
for ZQ Calibration command (short or long) after self refresh exit is tXS.
In systems that share the ZQ resistor between devices, the controller must not allow any overlap of tZQoper, tZQinit, or
tZQCS between ranks.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
78
REV 1.1
08 / 2010
ZQ Calibration Timing
Note:
1. CKE must be continuously registered high during the calibration procedure.
2. On-die termination must be disabled via the ODT signal or MRS during the calibration procedure.
3. All devices connected to the DQ bus should be high impedance during the calibration procedure.
ZQ External Resistor Value, Tolerance, and Capacitive loading
In order to use the ZQ calibration function, a 240 ohm +/- 1% tolerance external resistor connected between the ZQ pin and
ground. The single resistor can be used for each SDRAM or one resistor can be shared between two SDRAMs if the ZQ
calibration timings for each SDRAM do not overlap. The total capacitive loading on the ZQ pin must be limited.
CK
CK
Tc2
T0 T1 Ta1Ta3Tb0Tb1Tc1Ta0Ta2Tc0
Address
CMD ZQCL NOP NOP NOP Valid Valid ZQCS NOP NOP NOP Valid
ODT
tZQCS
Valid Valid
Valid Valid Valid
A10
CKE Valid Valid Valid
Valid Valid Valid
(1)
(2)
(1)
(2)
DQ Bus Hi-Z Activities Hi-Z Activities
tZQCS
(3) (3)
Do not
care Time
Break
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
79
REV 1.1
08 / 2010
Absolute Maximum Ratings
Absolute Maximum DC Ratings
Symbol
Parameter
Rating
Units
Note
VDD
Voltage on VDD pin relative to Vss
-0.4 ~ 1.975
V
1,3
VDDQ
Voltage on VDDQ pin relative to Vss
-0.4 ~ 1.975
V
1,3
Vin, Vout
Voltage on any pin relative to Vss
-0.4 ~ 1.975
V
1
Tstg
Storage Temperature
-55 ~ 100
C
1,2
Note:
1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This
is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM.
3. VDD and VDDQ must be within 300mV of each other at all times; and Vref must be not greater than 0.6VDDQ, when
VDD and VDDQ are less than 500mV; Vref may be equal to or less than 300mV.
Temperature Range
Symbol
Parameter
Rating
Units
Notes
Toper
Normal Operating Temperature Range
0 to 85
C
1,2
Extended Temperature Range
85 to 95
C
1,3
Note:
1. Operating Temperature Toper is the case surface temperature on the center/top side of the DRAM.
2. The Normal Temperature Range specifies the temperatures where all DRAM specification will be supported. During
operation, the DRAM case temperature must be maintained between 0-85C under all operating conditions.
3. Some applications require operation of the DRAM in the Extended Temperature Range between 85C and 95C case
temperature. Full specifications are guaranteed in this range, but the following additional apply:
a) Refresh commands must be doubled in frequency, therefore, reducing the Refresh interval tREFI to 3.9us. It is also
possible to specify a component with 1x refresh (tREFI to 7.8us) in the Extended Temperature Range.
b) If Self-Refresh operation is required in the Extended Temperature Range, then it is mandatory to either use the Manual
Self-Refresh mode with Extended Temperature Range capability (MR2 A6=0 and MR2 A7=1) or enable the optional Auto
Self-Refresh mode (MR2 A6=1 and MR2 A7=0).
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
80
REV 1.1
08 / 2010
AC & DC Operating Conditions
Recommended DC Operating Conditions
Symbol
Parameter
Rating
Unit
Note
Min.
Typ.
Max.
VDD
Supply Voltage
1.425
1.5
1.575
V
1,2
VDDQ
Supply Voltage for Output
1.425
1.5
1.575
V
1,2
VDD
Supply Voltage
1.28
1.35
1.45
V
1,2
VDDQ
Supply Voltage for Output
1.28
1.35
1.45
V
1,2
Note:
1. Under all conditions VDDQ must be less than or equal to VDD.
2. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
81
REV 1.1
08 / 2010
AC & DC Input Measurement Levels
AC and DC Logic Input Levels for Single-Ended Signals & Command and Address
Symbol
Parameter
DDR3-800/1066/1333/1600
Unit
Note
Min.
Max.
VIH.CA(DC100)
DC input logic high
Vref + 0.100
VDD
V
1
VIL.CA(DC100)
DC input logic low
VSS
Vref - 0.100
V
1
VIH.CA(AC175)
AC input logic high
Vref + 0.175
Note2
V
1,2
VIL.CA(AC175)
AC input logic low
Note2
Vref - 0.175
V
1,2
VIH.CA(AC150)
AC input logic high
Vref + 0.150
Note2
V
1,2
VIL.CA(AC150)
AC input logic low
Note2
Vref - 0.150
V
1,2
VREFCA(DC)
Reference Voltage for ADD, CMD inputs
0.49 * VDD
0.51 * VDD
V
3,4
Note:
1. For input only pins except RESET.Vref=VrefCA(DC)
2. See "Overshoot and Undershoot Specifications"
3. The ac peak noise on Vref may not allow Vref to deviate from Vref(DC) by more than +/- 0.1% VDD.
4. For reference: approx. VDD/2 +/- 15mV.
5. To allow VREFCA margining, all DRAM Command and Address Input Buffers MUST use external VREF (provided by system) as the
input for their VREFCA pins. All VIH/L input level MUST be compared with the external VREF level at the 1st stage of the Command and
Address input buffer
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
82
REV 1.1
08 / 2010
AC and DC Logic Input Levels for Single-Ended Signals & DQ and DM
Symbol
Parameter
DDR3-800/1066
DDR3-1333/1600
Unit
Note
Min.
Max.
Min.
Max.
VIH.DQ(DC100)
DC input logic high
Vref + 0.100
VDD
Vref + 0.100
VDD
V
1
VIL.DQ(DC100)
DC input logic low
VSS
Vref - 0.100
VSS
Vref - 0.100
V
1
VIH.DQ(AC175)
AC input logic high
Vref + 0.175
Note2
Vref + 0.150
Note2
V
1,2,5
VIL.DQ(AC175)
AC input logic low
Note2
Vref - 0.175
Note2
Vref - 0.150
V
1,2,5
VIH.DQ(AC150)
AC input logic high
Vref + 0.150
Note2
Vref + 0.150
Note2
V
1,2,5
VIL.DQ(AC150)
AC input logic low
Note2
Vref - 0.150
Note2
Vref - 0.150
V
1,2,5
VREFDQ(DC)
Reference Voltage for DQ, DM inputs
0.49 * VDD
0.51 * VDD
0.49 * VDD
0.51 * VDD
V
3,4
VREFDQ_t(DC)
Reference Voltage for trained DQ, DM inputs
0.45 * VDD
0.55 * VDD
0.45 * VDD
0.55 * VDD
V
3,4
6,7
Note:
1. For input only pins except . Vref = VrefDQ(DC)
2. See "Overshoot and Undershoot Specifications"
3. The ac peak noise on Vref may not allow Vref to deviate from Vref(DC) by more than ± 0.1% VDD.
4. For reference: approx. VDD/2 ±15mV.
5. Single-ended swing requirement for DQS-, is 350mV (peak to peak). Differential swing requirement for DQS-, is 700mV (peak to peak)
6. VRefDQ training is performed only during system boot. Once the training is completed and an optimal VRefDQ_t(DC) voltage level is identified, the optimal
VRefDQ_t(DC) voltage level will be used during system runtime. During VRefDQ training, VRefDQ is swept from 40% of VDD to 60% of VDD to find the
optimal VRefDQ_t(DC) voltage level; and once the optimal VRefDQ_t(DC) is set, it must stay within +/- 1% of its set value as well as not be less than 45% of
VDD or exceed 55% of VDD. VIH.DQ(AC)min/VIL.DQ(AC)max = Optimal VRefDQ_t(DC) +/- AC Level, where "AC Level" is the actual AC voltage level per
DDR3 speed bins as specified in JESD79-3 specification. After VRefDQ training is completed and the optimal VRefDQ_t(DC) is set, the Memory Controller
provides the DRAM device a valid write window. Through DQS placement optimization and VRefDQ centering, the valid write window is optimized for both
input voltage margin and tDS+tDH window for the DRAM receiver. The DRAM device supports the use of the above techniques to optimize the write timing
and voltage margin, as long as the technique does not create any DIMM failures due to DRAM input voltage and/or timing spec violations as defined in
JESD79-3 specification.
7. To allow VREFDQ margining, all DRAM Data Input Buffers MUST use external VREF (provided by system) as the input for their VREFDQ pins. All VIH/L input
level MUST be compared with the external VREF level at the 1st stage of the Data input buffer.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
83
REV 1.1
08 / 2010
Vref Tolerances
The dc-tolerance limits and ac-moist limits for the reference voltages VrefCA and VrefDQ are illustrated in the following figure. It
shows a valid reference voltage Vref(t) as a function of time. (Vref stands for VrefCA and VrefDQ likewise).
Vref(DC) is the linear average of Vref(t) over a very long period of time (e.g.,1 sec). This average has to meet the min/max
requirement in previous page. Furthermore Vref(t) may temporarily deviate from Vref(DC) by no more than ±1% VDD.
The voltage levels for setup and hold time measurements VIH(AC), VIH(DC), VIL(AC), and VIL(DC) are dependent on Vref.
“Vref” shall be understood as Vref(DC).
The clarifies that dc-variations of Vref affect the absolute voltage a signal has to reach to achieve a valid high or low level
and therefore the time to which setup and hold is measured. System timing and voltage budgets need to account for
Vref(DC) deviations from the optimum position within the data-eye of the input signals.
This also clarifies that the DRAM setup/hold specification and de-rating values need to include time and voltage associated
with Vref ac-noise. Timing and voltage effects due to ac-noise on Vref up to the specified limit (±1% of VDD) are included in
DRAM timing and their associated de-ratings.
Illustration of Vref(DC) tolerance and Vrefac-noise limits
Vref(DC)Vref(DC)max
Vref(DC)min
VDD/2
Vref ac-noise
Voltage
time
VDD
VSS
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
84
REV 1.1
08 / 2010
AC and DC Logic Input Levels for Differential Signals
Symbol
Parameter
DDR3-800, 1066, 1333, & 1600
Unit
Notes
Min.
Max.
VIHdiff
Differential input logic high
+0.200
Note3
V
1
VILdiff
Differential input logic low
Note3
-0.200
V
1
VIHdiff(ac)
Differential input high ac
2 x ( VIH(ac) Vref )
Note3
V
2
VILdiff(ac)
Differential input low ac
Note3
2 x ( Vref - VIL(ac) )
V
2
Note:
1. Used to define a differential signal slew-rate.
2. For CK - CK use VIH/VIL(ac) of ADD/CMD and VREFCA; for DQS - DQS, DQSL, DQSL, DQSU, DQSU use VIH/VIL(ac) of DQs and
VREFDQ; if a reduced ac-high or ac-low level is used for a signal group, then the reduced level applies also there.
3. These values are not defined, however the single-ended signals CK, CK, DQS, DQS, DQSL, DQSL, DQSU, DQSU need to be within the
respective limits (VIH(dc)max, VIL(dc)min) for single-ended signals as well as limitations for overshoot and undershoot.
Definition of differential ac-swing and “time above ac-level”
Time
Differential Input Voltage (i.e. DQS DQS, CK CK)
tDVAC
tDVAC
Half cycle
VIH.Diff.AC.min
VIH.Diff. DC min
VIL.Diff.AC.max
0
VIL. Diff. DC max
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
85
REV 1.1
08 / 2010
Allowed time before ring-back (tDVAC) for CK -  and DQS - 
Slew Rate [V/ns]
tDVAC [ps]
@IVIH/Ldiff(ac)I = 350mV
tDVAC [ps]
@IVIH/Ldiff(ac)I = 300mV
min
max
min
max
> 4.0
75
-
175
-
4.0
57
-
170
-
3.0
50
-
167
-
2.0
38
-
163
-
1.8
34
-
162
-
1.6
29
-
161
-
1.4
22
-
159
-
1.2
13
-
155
-
1.0
0
-
150
-
< 1.0
0
-
150
-
Single-ended requirements for differential signals
Each individual component of a differential signal (CK, DQS, DQSL, DQSU, , , , or ) has also to comply
with certain requirements for single-ended signals.
CK and  have to approximately reach VSEHmin / VSELmax (approximately equal to the ac-levels (VIH(ac) / VIL(ac)) for
ADD/CMD signals) in every half-cycle. DQS, DQSL, DQSU, DQS, DQSL, DQSL have to reach VSEHmin / VSELmax
(approximately the ac-levels (VIH(ac) / VIL(ac)) for DQ signals) in every half-cycle proceeding and following a valid
transition.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
86
REV 1.1
08 / 2010
Single-ended levels for CK, DQS, DQSL, DQSU, , , , or 
Symbol
Parameter
DDR3-800, 1066, 1333, & 1600
Unit
Notes
Min
Max
VSEH
Single-ended high-level for strobes
(VDDQ/2) + 0.175
note3
V
1, 2
Single-ended high-level for CK, CK
(VDDQ/2) + 0.175
note3
V
1, 2
VSEL
Single-ended low-level for strobes
note3
(VDDQ/2) - 0.175
V
1, 2
Single-ended Low-level for CK, CK
note3
(VDDQ/2) - 0.175
V
1, 2
Note:
1. For CK, CK use VIH/VIL(ac) of ADD/CMD; for strobes (DQS, DQSL, DQSU, CK, DQS, DQSL, or DQSU) use VIH/VIL(ac) of DQs.
2. VIH(ac)/VIL(ac) for DQs is based on VREFDQ; VIH(ac)/VIL(ac) for ADD/CMD is based on VREFCA; if a reduced ac-high or ac-low
level is used for a signal group, then the reduced level applies also there.
3. These values are not defined, however the single-ended signals CK, CK, DQS, DQS, DQSL, DQSL, DQSU, DQSU need to be within
the respective limits (VIH(dc)max, VIL(dc)min) for single-ended signals as well as limitations for overshoot and undershoot.
Differential Input Cross Point Voltage
To guarantee tight setup and hold times as well as output skew parameters with respect to clock and strobe, each cross
point voltage of differential input signals (CK, CK and DQS, DQS) must meet the requirements in the following table. The
differential input cross point voltage Vix is measured from the actual cross point of true and complete signal to the midlevel
between of VDD and VSS.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
87
REV 1.1
08 / 2010
Vix Definition
Cross point voltage for differential input signals (CK, DQS)
Symbol
Parameter
DDR3-800, 1066, 1333, & 1600
Unit
Note
Min.
Max.
Vix
Differential Input Cross Point Voltage relative to VDD/2 for CK, CK
-150
150
mV
-175
175
mV
1
Differential Input Cross Point Voltage relative to VDD/2 for DQS, DQS
-150
150
mV
Note1: Extended range for Vix is only allowed for clock and if single-ended clock input signals CK and  are monotonic with a
single-ended swing VSEL / VSEH of at least VDD/2 ± 250mV, and when the differential slew rate of CK -  is larger than 3V/ns.
Slew Rate Definition for Differential Input Signals
Differential Input Slew Rate Definition
Description
Measured
Defined by
From
To
Differential input slew rate for rising edge (CK- & DQS-)
VILdiffmax
VIHdiffmin
[VIHdiffmin-VILdiffmax] / DeltaTRdiff
Differential input slew rate for falling edge (CK- & DQS-)
VIHdiffmin
VILdiffmax
[VIHdiffmin-VILdiffmax] / DeltaTFdiff
The differential signal (i.e., CK- & DQS-) must be linear between these thresholds.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
88
REV 1.1
08 / 2010
Input Nominal Slew Rate Definition for single ended signals
Delta
TFdiff
Delta
TRdiff
VIHdiffMin
VILdiffMax
0
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
89
REV 1.1
08 / 2010
AC and DC Output Measurement Levels
Single Ended AC and DC Output Levels
Symbol
Parameter
Value
Unit
Notes
VOH(DC)
DC output high measurement level (for IV curve linearity)
0.8xVDDQ
V
VOM(DC)
DC output mid measurement level (for IV curve linearity)
0.5xVDDQ
V
VOL(DC)
DC output low measurement level (fro IV curve linearity)
0.2xVDDQ
V
VOH(AC)
AC output high measurement level (for output SR)
VTT+0.1xVDDQ
V
1
VOL(AC)
AC output low measurement level (for output SR)
VTT-0.1xVDDQ
V
1
Note:
1. The swing of ±0.1 x VDDQ is based on approximately 50% of the static single ended output high or low swing with a
driver impedance of 40 and an effective test load of 25 to VTT = VDDQ/2.
Differential AC and DC Output Levels
Symbol
Parameter
DDR3
Unit
Notes
VOHdiff(AC)
AC differential output high measurement level (for output SR)
+0.2 x VDDQ
V
1
VOLdiff(AC)
AC differential output low measurement level (for output SR)
-0.2 x VDDQ
V
1
Note:
1. The swing of ± 0.2 x VDDQ is based on approximately 50% of the static differential output high or low swing with a driver
impedance of 40 and an effective test load of 25 to VTT=VDDQ/2 at each of the differential outputs.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
90
REV 1.1
08 / 2010
Single Ended Output Slew Rate
Description
Measured
Defined by
From
To
Single ended output slew rate for rising edge
VOL(AC)
VOH(AC)
[VOH(AC)-VOL(AC)] / DeltaTRse
Single ended output slew rate for falling edge
VOH(AC)
VOL(AC)
[VOH(AC)-VOL(AC)] / DeltaTFse
Note: Output slew rate is verified by design and characterization, and may not be subject to production test.
Single Ended Output Slew Rate Definition
Output Slew Rate (single-ended)
Parameter
Symbol
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Unit
Min.
Max.
Min.
Max.
Max.
Max.
Max.
Max.
Single-ended Output Slew Rate
SRQse
2.5
5
2.5
5
2.5
5
TBD
5
V/ns
Note:
SR: Slew Rate.
Q: Query Output (like in DQ, which stands for Data-in, Query -Output).
se: Single-ended signals.
For Ron = RZQ/7 setting.
Delta
TFse
Delta
TRse
VOH(AC)
VOL(AC)
VTT
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
91
REV 1.1
08 / 2010
Differential Output Slew Rate
Description
Measured
Defined by
From
To
Differential output slew rate for rising edge
VOLdiff(AC)
VOHdiff(AC)
[VOHdiff(AC)-VOLdiff(AC)] / DeltaTRdiff
Differential output slew rate for falling edge
VOHdiff(AC)
VOLdiff(AC)
[VOHdiff(AC)-VOLdiff(AC)] / DeltaTFdiff
Note: Output slew rate is verified by design and characterization, and may not be subject to production test.
Differential Output Slew Rate Definition
Differential Output Slew Rate
Parameter
Symbol
Operation
Voltage
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Unit
Min.
Max.
Min.
Max.
Max.
Max.
Max.
Max.
Single-ended Output Slew Rate
SRQse
1.35V
3.5
12
3.5
12
3.5
12
3.5
12
V/ns
1.5V
5
12
5
12
5
12
5
12
V/ns
Note:
SR: Slew Rate.
Q: Query Output (like in DQ, which stands for Data-in, Query -Output).
diff: Differential signals.
For Ron = RZQ/7 setting.
Delta
TFdiff
Delta
TRdiff
VOHdiff(AC)
VOLdiff(AC)
0
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
92
REV 1.1
08 / 2010
Reference Load for AC Timing and Output Slew Rate
The following figure represents the effective reference load of 25 ohms used in defining the relevant AC timing parameters
of the device as well as output slew rate measurements.
It is not intended as a precise representation of any particular system environment or a depiction of the actual load
presented by a production tester. System designers should use IBIS or other simulation tools to correlate the timing
reference load to a system environment. Manufacturers correlate to their production test conditions, generally one or more
coaxial transmission lines terminated at the tester electronics.
25 Ohm Vtt = VDDQ / 2
CK, CK DUT
Timing Reference Points
VDDQ
DQ
DQS
DQS
RDQS
RDQS
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
93
REV 1.1
08 / 2010
Overshoot and Undershoot Specifications
AC Overshoot/Undershoot Specification for Address and Control Pins
Item
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Units
Maximum peak amplitude allowed for overshoot area
0.4
0.4
0.4
0.4
V
Maximum peak amplitude allowed for undershoot area
0.4
0.4
0.4
0.4
V
Maximum overshoot area above VDD
0.67
0.5
0.4
0.33
V-ns
Maximum undershoot area below VSS
0.67
0.5
0.4
0.33
V-ns
(A0-A15, BA0-BA3, , , , , CKE, ODT)
AC Overshoot/Undershoot Specification for Clock, Data, Strobe, and Mask
Item
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Units
Maximum peak amplitude allowed for overshoot area
0.4
0.4
0.4
0.4
V
Maximum peak amplitude allowed for undershoot area
0.4
0.4
0.4
0.4
V
Maximum overshoot area above VDD
0.25
0.19
0.15
0.13
V-ns
Maximum undershoot area below VSS
0.25
0.19
0.15
0.13
V-ns
(CK, , DQ, DQS, , DM)
VDD
VSS
Overshoot Area
Undershoot Area
Maximum Amplitude
Maximum Amplitude
Time (ns)
Volts (V)
VDDQ
VSSQ
Overshoot Area
Undershoot Area
Maximum Amplitude
Maximum Amplitude
Time (ns)
Volts (V)
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
94
REV 1.1
08 / 2010
34 Ohm Output Driver DC Electrical Characteristics
A Functional representation of the output buffer is shown as below. Output driver impedance RON is defined by the value of
the external reference resistor RZQ as follows:
RON34 = RZQ / 7 (nominal 34.4ohms +/-10% with nominal RZQ=240ohms)
The individual pull-up and pull-down resistors (RONPu and RONPd) are defined as follows:
RONPu = [VDDQ-Vout] / l Iout l ------------------- under the condition that RONPd is turned off (1)
RONPd = Vout / I Iout I -------------------------------under the condition that RONPu is turned off (2)
To
other
circuitry
like
RCV,...
RON
RON
Pu
Pd
IPu
IPd
VDDQ
VSSQ
DQ
IOut VOut
Output Driver
Chip in Drive Mode
Output Driver DC Electrical Characteristics, assuming RZQ = 240ohms; entire
operating temperature range; after proper ZQ calibration
RONNom
Resistor
Vout
min
nom
max
Unit
Notes
34 ohms
RON34Pd
VOLdc = 0.2 x VDDQ
0.6
1
1.1
RZQ / 7
1,2,3
VOMdc = 0.5 x VDDQ
0.9
1
1.1
RZQ / 7
1,2,3
VOHdc = 0.8 x VDDQ
0.9
1
1.4
RZQ / 7
1,2,3
RON34Pu
VOLdc = 0.2 x VDDQ
0.9
1
1.4
RZQ / 7
1,2,3
VOMdc = 0.5 x VDDQ
0.9
1
1.1
RZQ / 7
1,2,3
VOHdc = 0.8 x VDDQ
0.6
1
1.1
RZQ / 7
1,2,3
Mismatch between pull-up and pull-down, MMPuPd
VOMdc = 0.5 x VDDQ
-10
+10
%
1,2,4
Note:
1. The tolerance limits are specified after calibration with stable voltage and temperature. For the behavior of the tolerance limits if
temperature or voltage changes after calibration, see following section on voltage and temperature sensitivity.
2. The tolerance limits are specified under the condition that VDDQ = VDD and that VSSQ = VSS.
3. Pull-down and pull-up output driver impedances are recommended to be calibrated at 0.5 x VDDQ. Other calibration schemes may be
used to achieve the linearity spec shown above. e.g. calibration at 0.2 x VDDQ and 0.8 x VDDQ.
4. Measurement definition for mismatch between pull-up and pull-down, MMPuPd:
Measure RONPu and RONPd, but at 0.5 x VDDQ:
MMPuPd = [RONPu - RONPd] / RONNom x 100
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
95
REV 1.1
08 / 2010
Output Driver Temperature and Voltage sensitivity
If temperature and/or voltage after calibration, the tolerance limits widen according to the following table.
Delta T = T - T(@calibration); Delta V = VDDQ - VDDQ(@calibration); VDD = VDDQ
Note: dRONdT and dRONdV are not subject to production test but are verified by design and characterization.
Items
Min.
Max.
Unit
RONPU@VOHdc
0.6 - dRONdTH*lDelta Tl - dRONdVH*lDelta Vl
1.1 + dRONdTH*lDelta Tl - dRONdVH*lDelta Vl
RZQ/7
RON@VOMdc
0.9 - dRONdTM*lDelta Tl - dRONdVM*lDelta Vl
1.1 + dRONdTM*lDelta Tl - dRONdVM*lDelta Vl
RZQ/7
RONPD@VOLdc
0.6 - dRONdTL*lDelta Tl - dRONdVL*lDelta Vl
1.1 + dRONdTL*lDelta Tl - dRONdVL*lDelta Vl
RZQ/7
Output Driver Voltage and Temperature Sensitivity
Speed Bin
DDR3-800/1066/1333
DDR3-1600
Unit
Items
Min.
Max
Min.
Max
dRONdTM
0
1.5
0
1.5
%/C
dRONdVM
0
0.15
0
0.13
%/mV
dRONdTL
0
1.5
0
1.5
%/C
dRONdVL
0
0.15
0
0.13
%/mV
dRONdTH
0
1.5
0
1.5
%/C
dRONdVH
0
0.15
0
0.13
%/mV
Note: These parameters may not be subject to production test. They are verified by design and characterization.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
96
REV 1.1
08 / 2010
On-Die Termination (ODT) Levels and I-V Characteristics
On-Die Termination effective resistance RTT is defined by bits A9, A6, and A2 of the MR1 Register.
ODT is applied to the DQ, DM, DQS/DQS, and TDQS/TDQS (x8 devices only) pins.
A functional representation of the on-die termination is shown in the following figure. The individual pull-up and pull-down
resistors (RTTPu and RTTPd) are defined as follows:
RTTPu = [VDDQ - Vout] / I Iout I ------------------ under the condition that RTTPd is turned off (3)
RTTPd = Vout / I Iout I ------------------------------ under the condition that RTTPu is turned off (4)
ODT DC Electrical Characteristics
The following table provides an overview of the ODT DC electrical characteristics. The values for RTT60Pd120, RTT60Pu120,
RTT120Pd240, RTT120Pu240, RTT40Pd80, RTT40Pu80, RTT30Pd60, RTT30Pu60, RTT20Pd40, RTT20Pu40 are not specification
requirements, but can be used as design guide lines:
To other
circuitry
like
RCV, ...
RTT
RTT
Pu
Pd
IPu
IPd
VDDQ
VSSQ
DQ
IOut VOut
ODT
Chip in Termination Mode
I = I - I
Out Pd Pu
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
97
REV 1.1
08 / 2010
ODT DC Electrical Characteristics, assuming RZQ = 240ohms +/- 1% entire operating
temperature range; after proper ZQ calibration
MR1 A9, A6, A2
RTT
Resistor
Vout
min
nom
max
Unit
Notes
0,1,0
120
RTT120Pd240
VOLdc = 0.2 x VDDQ
0.6
1
1.1
RZQ
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ
1,2,3,4
VOHdc = 0.8 x VDDQ
0.9
1
1.4
RZQ
1,2,3,4
RTT120Pu240
VOLdc = 0.2 x VDDQ
0.9
1
1.4
RZQ
1,2,3,4
0.5 x VDDQ
0.9
1
1,1
RZQ
1,2,3,4
VOHdc = 0.8 x VDDQ
0.6
1
1.1
RZQ
1,2,3,4
RTT120
VIL(ac) to VIH(ac)
0.9
1
1.6
RZQ /2
1,2,5
0, 0, 1
60
RTT60Pd120
VOLdc = 0.2 x VDDQ
0.6
1
1.1
RZQ/2
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/2
1,2,3,4
VOHdc = 0.8 x VDDQ
0.9
1
1.4
RZQ/2
1,2,3,4
RTT60Pu120
VOLdc = 0.2 x VDDQ
0.9
1
1.4
RZQ/2
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/2
1,2,3,4
VOHdc = 0.8 x VDDQ
0.6
1
1.1
RZQ/2
1,2,3,4
RTT60
VIL(ac) to VIH(ac)
0.9
1
1.6
RZQ/4
1,2,5
0, 1, 1
40
RTT40Pd80
VOLdc = 0.2 x VDDQ
0.6
1
1.1
RZQ/3
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/3
1,2,3,4
VOHdc = 0.8 x VDDQ
0.9
1
1.4
RZQ/3
1,2,3,4
RTT40Pu80
VOLdc = 0.2 x VDDQ
0.9
1
1.4
RZQ/3
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/3
1,2,3,4
VOHdc = 0.8 x VDDQ
0.6
1
1.1
RZQ/3
1,2,3,4
RTT40
VIL(ac) to VIH(ac)
0.9
1
1.6
RZQ/6
1,2,5
1, 0, 1
30
RTT30Pd60
VOLdc = 0.2 x VDDQ
0.6
1
1.1
RZQ/4
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/4
1,2,3,4
VOHdc = 0.8 x VDDQ
0.9
1
1.4
RZQ/4
1,2,3,4
RTT30Pu60
VOLdc = 0.2 x VDDQ
0.9
1
1.4
RZQ/4
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/4
1,2,3,4
VOHdc = 0.8 x VDDQ
0.6
1
1.1
RZQ/4
1,2,3,4
RTT30
VIL(ac) to VIH(ac)
0.9
1
1.6
RZQ/8
1,2,5
1, 0, 0
20
RTT20Pd40
VOLdc = 0.2 x VDDQ
0.6
1
1.1
RZQ/6
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/6
1,2,3,4
VOHdc = 0.8 x VDDQ
0.9
1
1.4
RZQ/6
1,2,3,4
RTT20Pu40
VOLdc = 0.2 x VDDQ
0.9
1
1.4
RZQ/6
1,2,3,4
0.5 x VDDQ
0.9
1
1.1
RZQ/6
1,2,3,4
VOHdc = 0.8 x VDDQ
0.6
1
1.1
RZQ/6
1,2,3,4
RTT20
VIL(ac) to VIH(ac)
0.9
1
1.6
RZQ/12
1,2,5
Deviation of VM w.r.t. VDDQ/2, DVm
-5
+5
%
1,2,5,6
Note:
1. The tolerance limits are specified after calibration with stable voltage and temperature. For the behavior of the tolerance limits if
temperature or voltage changes after calibration, see following section on voltage and temperature sensitivity.
2. The tolerance limits are specified under the condition that VDDQ = VDD and that VSSQ = VSS.
3. Pull-down and pull-up ODT resistors are recommended to be calibrated at 0.5 x VDDQ. Other calibration may be used to achieve the lin-
earity spec shown above.
4. Not a specification requirement, but a design guide line.
5. Measurement definition for RTT:
Apply VIH(ac) to pin under test and measure current / (VIH(ac)), then apply VIL(ac) to pin under test and measure current / (VIL(ac))
respectively.
RTT = [VIH(ac) - VIL(ac)] / [I(VIH(ac)) - I(VIL(ac))]
6. Measurement definition for VM and DVM:
Measure voltage (VM) at test pin (midpoint) with no lead:
Delta VM = [2VM / VDDQ -1] x 100
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
98
REV 1.1
08 / 2010
ODT Temperature and Voltage sensitivity
If temperature and/or voltage after calibration, the tolerance limits widen according to the following table.
Delta T = T - T(@calibration); Delta V = VDDQ - VDDQ(@calibration); VDD = VDDQ
ODT Sensitivity Definition
min
max
Unit
RTT
0.9 - dRTTdT*lDelta Tl - dRTTdV*lDelta Vl
1.6 + dRTTdT*lDelta Tl + dRTTdV*lDelta Vl
RZQ/2,4,6,8,12
ODT Voltage and Temperature Sensitivity
min
max
Unit
dRTTdT
0
1.5
%/C
dRTTdV
0
0.15
%/mV
Note: These parameters may not be subject to production test. They are verified by design and characterization.
Test Load for ODT Timings
Different than for timing measurements, the reference load for ODT timings is defined in the following figure.
ODT Timing Definitions
Definitions for tAON, tAONPD, tAOF, tAOFPD, and tADC are provided in the following table and subsequent figures.
Symbol
Begin Point Definition
End Point Definition
tAON
Rising edge of CK - CK defined by the end point of ODTLon
Extrapolated point at VSSQ
tAONPD
Rising edge of CK - CK with ODT being first registered high
Extrapolated point at VSSQ
tAOF
Rising edge of CK - CK defined by the end point of ODTLoff
End point: Extrapolated point at VRTT_Nom
tAOFPD
Rising edge of CK - CK with ODT being first registered low
End point: Extrapolated point at VRTT_Nom
tADC
Rising edge of CK - CK defined by the end point of ODTLcnw,
ODTLcwn4, or ODTLcwn8
End point: Extrapolated point at VRTT_Wr and
VRTT_Nom respectively
25Ohm Vtt = VSSQ
DUT
Timing Reference Points
VDDQ
DQ
DQS
DQS
RDQS
RDQS
VSSQ
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
99
REV 1.1
08 / 2010
Reference Settings for ODT Timing Measurements
Measured Parameter
RTT_Nom Setting
RTT_Wr Setting
VSW1[V]
VSW2[V]
Note
tAON
RZQ/4
NA
0.05
0.10
RZQ/12
NA
0.10
0.20
tAONPD
RZQ/4
NA
0.05
0.10
RZQ/12
NA
0.10
0.20
tAOF
RZQ/4
NA
0.05
0.10
RZQ/12
NA
0.10
0.20
tAOFPD
RZQ/4
NA
0.05
0.10
RZQ/12
NA
0.10
0.20
tADC
RZQ/12
RZQ/2
0.20
0.30
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
100
REV 1.1
08 / 2010
Definition of tAON
Definition of tAONPD
tAON
Tsw2
Tsw1
Vsw1Vsw2
VSSQ
VTT
DQ, DM
DQS, DQS#
TDQS, TDQS#
End point: Extrapolated point at VSSQ
CK
CK#
Begin point: Rising edge of CK CK#
Defined by the end point of ODTLon
tAONPD
Tsw2
Tsw1
Vsw1Vsw2
VSSQ
VTT
DQ, DM
DQS, DQS#
TDQS, TDQS#
End point: Extrapolated point at VSSQ
CK
CK#
Begin point: Rising edge of CK CK#
with ODT being first register high
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
101
REV 1.1
08 / 2010
Definition of tAOF
Definition of tAOFPD
tAOF
Tsw2
Tsw1
Vsw1
Vsw2
VSSQ
VTT
DQ, DM
DQS, DQS#
TDQS, TDQS#
End point: Extrapolated point at VRTT_Nom
CK
CK#
Begin point: Rising edge of CK CK#
defined by the end point of ODTLoff
VRTT_Nom
tAOFPD
Tsw2
Tsw1
Vsw1
Vsw2
VSSQ
VTT
DQ, DM
DQS, DQS#
TDQS, TDQS#
End point: Extrapolated point at VRTT_Nom
CK
CK#
Begin point: Rising edge of CK CK#
with ODT being first registered low
VRTT_Nom
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
102
REV 1.1
08 / 2010
Definition of tADC
tADC
Tsw21
Tsw11
Vsw1
Vsw2
DQ, DM
DQS, DQS#
TDQS, TDQS#
End point: Extrapolated point at VRTT_Nom
CK
CK#
Begin point: Rising edge of CK CK#
defined by the end of ODTLcnw
VRTT_Nom
tADC
Tsw22
Tsw12
VSSQ
VTT
End point: Extrapolated point at VRTT_Wr
CK
CK#
Begin point: Rising edge of CK CK# defined
by the end of ODTLcwn4 or ODTLcwn8
VRTT_Wr
VRTT_Nom
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
103
REV 1.1
08 / 2010
Input / Output Capacitance
Symbol
Parameter
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Units
Notes
Min.
Max
Min.
Max
Min.
Max
Min.
Max
CIO
Input/output capacitance (DQ, DM, DQS, , TDQS, )
1.50
3.00
1.50
3.00
1.50
2.50
1.50
2.30
pF
1,2,3
CCK
Input capacitance, CK and CK
0.80
1.60
0.80
1.60
0.80
1.40
0.80
1.40
pF
2,3
CDCK
Input capacitance delta, CK and 
0.00
0.15
0.00
0.15
0.00
0.15
0.00
0.15
pF
2,3,4
CDDQS
Input/output capacitance delta, DQS and 
0.00
0.20
0.00
0.20
0.00
0.15
0.00
0.15
pF
2,3,5
CI
Input capacitance, CTRL, ADD, CMD input-only pins
0.75
1.40
0.75
1.35
0.75
1.30
0.75
1.30
pF
2,3,7,8
CDI_CTRL
Input capacitance delta, all CTRL input-only pins
-0.50
0.30
-0.50
0.30
-0.40
0.20
-0.40
0.20
pF
2,3,7,8
CDI_ADD_CMD
Input capacitance delta, all ADD/CMD input-only pins
-0.50
0.50
-0.50
0.50
-0.40
0.40
-0.40
0.40
pF
2,3,9,10
CDIO
Input/output capacitance delta, DQ, DM, DQS, , TDQS, 
-0.50
0.30
-0.50
0.30
-0.50
0.30
-0.50
0.30
pF
2,3,11
CZQ
Input/output capacitance of ZQ pin
-
3.00
-
3.00
-
3.00
-
3.00
pF
2,3,12
1. Although the DM, TDQS and TDQS pins have different functions, the loading matches DQ and DQS
2. This parameter is not subject to production test. It is verified by design and characterization. VDD=VDDQ=1.5V, VBIAS=VDD/2 and on-die termination off.
3. This parameter applies to monolithic devices only; stacked/dual-die devices are not covered here
4. Absolute value of CCK-CCK
5. Absolute value of CIO(DQS)-CIO(DQS)
6. CI applies to ODT, , CKE, A0-A13, BA0-BA2, , , .
7. CDI_CTRL applies to ODT,  and CKE
8. CDI_CTRL=CI(CTRL)-0.5*(CI(CLK)+CI(CLK))
9. CDI_ADD_CMD applies to A0-A13, BA0-BA2, ,  and 
10. CDI_ADD_CMD=CI(ADD_CMD) - 0.5*(CI(CLK)+CI())
11. CDIO=CIO(DQ,DM) - 0.5*(CIO(DQS)+CIO))
12. Maximum external load capacitance on ZQ pin: 5 pF.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
104
REV 1.1
08 / 2010
IDD Specifications and Measurement Conditions
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
Symbol
Parameter/Condition
DDR3-800MHz
(-AC/-AD)
DDR3-1066MHz
(-BE)
DDR3-1333MHz
(-CG)
DDR3-1600MHz
(DI)
Unit
X4
X8
X16
X4
X8
X16
X4
X8
X16
X4
X8
X16
IDD0
Operating Current 0
-> One Bank Activate
-> Precharge
70
70
80
75
75
90
85
85
100
95
95
110
mA
IDD1
Operating Current 1
-> One Bank Activate
-> Read
-> Precharge
90
90
120
95
95
125
100
100
130
105
105
135
mA
IDD2P0
Precharge Power-Down Current
Slow Exit - MR0 bit A12 = 0
12
12
12
12
12
12
12
12
12
12
12
12
mA
IDD2P1
Precharge Power-Down Current
Fast Exit - MR0 bit A12 = 1
20
20
25
25
25
30
30
30
35
35
35
40
mA
IDD2Q
Precharge Quiet Standby Current
25
25
25
30
30
30
35
35
35
40
40
40
mA
IDD2N
Precharge Standby Current
30
30
30
35
35
35
40
40
40
45
45
45
mA
IDD3P
Active Power-Down Current
Always Fast Exit
25
25
30
30
30
35
35
35
40
40
40
45
mA
IDD3N
Active Standby Current
30
30
30
35
35
35
40
40
40
45
45
45
mA
IDD4R
Operating Current Burst Read
120
120
180
140
140
210
160
160
240
180
180
270
mA
IDD4W
Operating Current Burst Write
125
125
190
145
145
210
165
165
255
185
185
280
mA
IDD5B
Burst Refresh Current
180
180
180
190
190
190
200
200
200
210
210
210
mA
IDD6
Self-Refresh Current Normal Temperature Range (0-85°C)
12
12
12
12
12
12
12
12
12
12
12
12
mA
IDD7
All Bank Interleave Read Current
280
280
300
310
310
330
330
330
370
370
370
400
mA
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
105
REV 1.1
08 / 2010
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
Symbol
Parameter/Condition
DDR3-800MHz
(-AC/-AD)
DDR3-1066MHz
(-BE)
DDR3-1333MHz
(-CG)
DDR3-1600MHz
(-DI)
Unit
X4
X8
X16
X4
X8
X16
X4
X8
X16
X4
X8
X16
IDD0
Operating Current 0
-> One Bank Activate
-> Precharge
65
65
73
69
69
83
78
78
92
87
87
100
mA
IDD1
Operating Current 1
-> One Bank Activate
-> Read
-> Precharge
83
83
110
87
87
115
92
92
120
96
96
124
mA
IDD2P0
Precharge Power-Down Current
Slow Exit - MR0 bit A12 = 0
11
11
11
11
11
11
11
11
11
11
11
11
mA
IDD2P1
Precharge Power-Down Current
Fast Exit - MR0 bit A12 = 1
18.5
18.5
23
23
23
27.5
27.5
27.5
32
32
32
36.5
mA
IDD2Q
Precharge Quiet Standby Current
23
23
23
27.5
27.5
27.5
32
32
32
36.5
36.5
36.5
mA
IDD2N
Precharge Standby Current
27.5
27.5
27.5
32
32
32
36.5
36.5
36.5
41.5
41.5
41.5
mA
IDD3P
Active Power-Down Current
Always Fast Exit
23
23
27.5
27.5
27.5
32
32
32
36.5
36.5
36.5
41.5
mA
IDD3N
Active Standby Current
27.5
27.5
27.5
32
32
32
36.5
36.5
36.5
41.5
41.5
41.5
mA
IDD4R
Operating Current Burst Read
110
110
165
130
130
190
147
147
220
165
165
247.5
mA
IDD4W
Operating Current Burst Write
115
115
175
130
130
190
150
150
235
170
170
255
mA
IDD5B
Burst Refresh Current
165
165
165
175
175
175
185
185
185
190
190
190
mA
IDD6
Self-Refresh Current Normal Temperature Range (0-85°C)
11
11
11
11
11
11
11
11
11
11
11
11
mA
IDD7
All Bank Interleave Read Current
250
250
270
280
280
300
300
300
340
330
330
370
mA
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
106
REV 1.1
08 / 2010
IDD Measurement Conditions
Symbol
Parameter/Condition
IDD0
Operating Current - One bank Active - Precharge current
CKE: High; External clock: On; tCK, tRC, tRAS: see table in the next page; CS: High between ACT and PRE; Command Inputs: SWITCHING1 (except for ACT and PRE); Row,
Column Address, Data I/O: SWITCHING1 (A10 Low permanently); Bank Address: fixed (Bank 0); Output Buffer: off 2; ODT: disabled 3; Active Banks: one (ACT-PRE loop); Idle Banks:
all other; Pattern example: A0 D DD DD DD DD DD DD D P04 (DDR3-800: tRAS=37.5ns)
IDD1
Operating One bank Active-Read-Precharge Current
CKE: High; External clock: On; tCK, tRC, tRAS, tRCD, CL, AL: see table in the next page; CS: High between ACT, RD, and PRE; Command Inputs: SWITCHING1 (except ACT, RD,
and PRE Commands); Row, Column Address: SWITCHING1 (A10 Low permanently); Bank Address: fixed (Bank 0); Data I/O: switching every clock (RD Data stable during one
Clock cycle); floating when no burst activity; Output Buffer: Off2; ODT: disabled 3; Burst Length: BL85; Active Banks: one (ACT-RD-PRE loop); Idle Banks: all other; Pattern example:
A0 D DD D R0 DD DD DD DD D P04 (DDR3-800-5-5-5: tRCD=12.5ns).
IDD2N
Precharge Standby Current
CKE=High; External Clock=On; tCK: see table in the next page; CS: High; Command Inputs, Row, Column, Bank Address, Data I/O: SWITCHING1 ; Output Buffer: Off2; ODT:
disabled 3; Active / Idle Banks: none / all.
IDD2P(0)
Precharge Power-Down Current - (Slow Exit)
CKE=Low; External Clock=On; tCK: see table in the next page; CS: Stable; Command Inputs: Stable; Row, Column / Bank Address: Stable; Data I/O: floating; Output Buffer: Off2;
ODT: disabled 3; Active / Idle Banks: none / all. Precharge Power Down Mode: Slow Exit 6(RD and ODT must satisfy tXPDLL - AL)
IDD2P(1)
Precharge Power-Down Current - (Fast Exit)
CKE=Low; External Clock=On; tCK: see table in the next page; CS: Stable; Command Inputs, Row, Column, Bank Address: Stable; Data I/O: floating; Output Buffer: Off2; ODT:
disabled 3; Active / Idle Banks: none / all. Precharge Power Down Mode: Fast Exit 6(any valid Command after tXP)7
IDD2Q
Precharge Quiet Standby Current
CKE=High; External Clock=On; tCK: see table in the next page; CS=High; Command Inputs, Row, Column, Bank Address: Stable; Data I/O: floating; Output Buffer: Off2; ODT:
disabled 3; Active / Idle Banks: none / all.
IDD3N
Active Standby Current
CKE=High; External Clock=On; tCK: see table in the next page; CS=High; Command Inputs, Row, Column, Bank Address, Data I/O: SWITCHING1; Output Buffer: Off2; ODT:
disabled 3; Active / Idle Banks: All / none.
IDD3P
Active Power-Down Current
CKE=Low; External Clock=On; tCK: see table in the next page; CS, Command Inputs, Row, Column, Bank Address: Stable; Data I/O: floating; Output Buffer: Off2; ODT: disabled 3;
Active / Idle Banks: All / none.
IDD4R
Operating Burst Read Current
CKE=High; External Clock=On; tCK, CL: see table in the next page; AL: 0; CS: High between valid Commands; Command Inputs: SWITCHING1(except RD Commands); Row,
Column Address: SWITCHING1(A10: Low permanently); Bank Address: cycling10; Data I/O: Seamless Read Data Burst : Output Data switches every clock cycle (i.e. data stable
during one clock cycle); Output Buffer: Off2; ODT: disabled 3; Burst Length: BL85; Active / Idle Banks: All / none10; Pattern: R0 D DD R1 D DD R2 D DD R3 D DD R44
IDD4W
Operating Burst Write Current
CKE=High; External Clock=On; tCK, CL: see table in the next page; AL: 0; CS: High between valid Commands; Command Inputs: SWITCHING1(except WR Commands); Row,
Column Address: SWITCHING1(A10: Low permanently); Bank Address: cycling10; Data I/O: Seamless Write Data Burst : Input Data switches every clock cycle (i.e. data stable during
one clock cycle); DM: L permanently; Output Buffer: Off2; ODT: disabled 3; Burst Length: BL85; Active / Idle Banks: All / none10; Pattern: W0 D DD W1 D DD W2 D DD W3 D DD W44
IDD5B
Burst Refresh Current
CKE=High; External Clock=On; tCK, tRFC: see table in the next page; CS: High between valid Commands; Command Inputs, Row, Column, Bank Addresses, Data I/O:
SWITCHING1; Output Buffer: Off2; ODT: disabled 3; Active Banks: Refresh Command every tRFC=tRFC(IDD); Idle banks: none.
IDD6
Self-Refresh Current
Tcase=0-85C; Auto Self Refresh =Disable; Self Refresh Temperature Range=Normal9; CKE=Low; External Clock=Off (CK and CK: Low); CS, Command Inputs, Row, Column
Address, Bank Address, Data I/O: Floating; Output Buffer: off 2; ODT: disabled 3; Active Banks: All (during Self-Refresh action); Idle Banks: all (between Self-Rerefresh actions)
IDD6ET
Self-Refresh Current: extended temperature range
Tcase=0-95C; Auto Self Refresh =Disable; Self Refresh Temperature Range=Extended9; CKE=Low; External Clock=Off (CK and CK: Low); CS, Command Inputs, Row, Column
Address, Bank Address, Data I/O: Floating; Output Buffer: off 2; ODT: disabled 3; Active Banks: All (during Self-Refresh action); Idle Banks: all (between Self-Rerefresh actions)
IDD6TC
Auto Self-Refresh Current
Tcase=0-95C; Auto Self Refresh =Enable8; Self Refresh Temperature Range=Normal9; CKE=Low; External Clock=Off (CK and CK: Low); CS, Command Inputs, Row, Column
Address, Bank Address, Data I/O: Floating; Output Buffer: off 2; ODT: disabled 3; Active Banks: All (during Self-Refresh action); Idle Banks: all (between Self-Rerefresh actions)
IDD7
Operating Bank Interleave Read Current
CKE=High; External Clock=On; tCK, tRC, tRAS, tRCD, tRRD, CL: see table as below; AL=tRCD.min-tCK; CS=High between valid commands; Command Input: see table; Row,
Column Address: Stable during DESELECT; Bank Address: cycling10; Data I/O: Read Data: Output Data switches every clock cycle (i.e. data stable during one clock cycle); Output
Buffer: Off 2;ODT: disabled 3; Burst Length: BL8; Active / Idle Banks: All 10 / none.
Note1: SWITCHING for Address and Command Input Signals as described in Definition of SWITCHING for Address and Command Input Signals Table.
Note2: Output Buffer off: set MR1 A[12] = 1
Note3: ODT disable: set MR1 A[9,6,2]=000 and MR2 A[10,9]=00
Note4: Definition of D and D: described in Definition of SWITCHING for Address and Command Input Signals Table; Ax/Rx/Wx: Activate/Read/Write to Bank x.
Note5: BL8 fixed by MRS: set MR0 A[1,0]=00
Note6: Precharge Power Down Mode: set MR0 A12=0/1 for Slow/Fast Exit
Note7: Because it is an exit after precharge power down, the valid commands are: ACT, REF, MRS, Enter Self-Refresh.
Note8: Auto Self-Refresh(ASR): set MR2 A6 = 0/1 to disable/enable feature
Note9: Self-Refresh Temperature Range (SRT): set MR2 A7 = 0/1 for normal/extended temperature range
Note10: Cycle banks as follows: 0,1,2,3,...,7,0,1,...
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
107
REV 1.1
08 / 2010
For ID testing the following parameters are utilized.
For testing the IDD parameters, the following timing parameters are used:
Parameter
Symbol
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
Unit
(-AC)
(-AD)
(-BE)
(-CG)
(-DI)
-5-5-5
-6-6-6
-7-7-7
-9-9-9
-11-11-11
Clock Cycle Time
tCKmin(IDD)
2.5
2.5
1.875
1.5
1.25
ns
CAS Latency
CL(IDD)
5
6
7
9
11
nCK
Active to Read or Write delay
tRCDmin(IDD)
12.5
15
13.125
12
13.125
ns
Active to Active / Auto-Refresh command period
tRCmin(IDD)
50
52.5
50.63
48
48.125
ns
Active to Precharge Command
tRASmin(IDD)
37.5
37.5
37.5
36
35
ns
Precharge Command Period
tRPmin(IDD)
12.5
15
13.13
12
13.75
ns
Four activate window
1kB
tFAW(IDD)
40
40
37.5
30
30
ns
2kB
50
50
50
45
40
ns
Active to Active command period
1kB
tRRD(IDD)
10
10
7.5
6
6
nCK
2kB
10
10
10
7.5
7.5
nCK
Auto-Refresh to Active / Auto-Refresh command
period
tRFC(IDD)
160
160
160
160
160
ns
Definition of SWITCHING for Address and Command Input Signals
SWITCHING for Address (row, column) and Command Signals (CS, RAS, CAS, WE) is defined as:
Address
(row, column)
If not otherwise mentioned the inputs are stable at HIGH or LOW during 4 clocks and change
then to the opposite value
(e.g. Ax Ax Ax Ax     Ax Ax Ax Ax…
Please see each IDDx definition for details
Bank Address
If not otherwise mentioned the bank addresses should be switched like the row/column address -
please see each IDDx for details
Command
(, , , )
Define D = {, , , } := {HIGH, LOW, LOW, LOW}
Define D = {, , ,  } := {HIGH, HIGH, HIGH, HIGH}
Define Command Background Pattern = D D D D D D ....
If other commands are necessary (e.g. ACT for IDD0 or Read for IDD4R), the Background
Pattern Command is substituted by the respective , , ,  levels of the necessary
command. See each IDDx definition for details.
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
108
REV 1.1
08 / 2010
Standard Speed Bins
DDR3-800MHz
Speed Bin
DDR3-800
Unit
CL-nRCD-nRP
5-5-5 (-AC)
6-6-6 (-AD)
Parameter
Symbol
Min
Max
Min
Max
Internal read command to first data
tAA
12.500
20.000
15.000
20.000
ns
ACT to internal read or write delay
time
tRCD
12.500
-
15.000
-
ns
PRE command period
tRP
12.500
-
15.000
-
ns
ACT to ACT or REF command
period
tRC
50.000
-
52.200
-
ns
ACT to PRE command period
tRAS
37.500
9*tREFI
37.500
9*tREFI
ns
CL=5
CWL =5
tCK(AVG)
2.500
3.300
3.000
3.300
ns
CL=6
CWL =5
tCK(AVG)
2.500
3.300
2.500
3.300
ns
Supported CL Settings
5,6
6
nCK
Supported CWL Settings
5
5
nCK
DDR3-1066MHz
Speed Bin
DDR3-1066
Unit
CL-nRCD-nRP
7-7-7 (-BE)
Parameter
Symbol
Min
Max
Internal read command to first data
tAA
13.125
20.000
ns
ACT to internal read or write delay time
tRCD
13.125
-
ns
PRE command period
tRP
13.125
-
ns
ACT to ACT or REF command period
tRC
50.625
-
ns
ACT to PRE command period
tRAS
37.500
9*tREFI
ns
CL=5
CWL=5
tCK(AVG)
3.000
3.300
ns
CWL=6
tCK(AVG)
Reserved
ns
CL=6
CWL=5
tCK(AVG)
2.500
3.300
ns
CWL=6
tCK(AVG)
Reserved
ns
CL=7
CWL=5
tCK(AVG)
Reserved
ns
CWL=6
tCK(AVG)
1.875
<2.5
ns
CL=8
CWL=5
tCK(AVG)
Reserved
ns
CWL=6
tCK(AVG)
1.875
<2.5
ns
Supported CL Settings
6,7,8
nCK
Supported CWL Settings
5,6
nCK
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
109
REV 1.1
08 / 2010
DDR3-1333MHz
Speed Bin
DDR3-1333
Unit
CL-nRCD-nRP
9-9-9 (-CG)
Parameter
Symbol
Min
Max
Internal read command to first data
tAA
13.125
20.000
ns
ACT to internal read or write delay time
tRCD
13.125
-
ns
PRE command period
tRP
13.125
-
ns
ACT to ACT or REF command period
tRC
49.125
-
ns
ACT to PRE command period
tRAS
36.000
9*tREFI
ns
CL=5
CWL=5
tCK(AVG)
3.000
3.300
ns
CWL=6
tCK(AVG)
Reserved
Reserved
ns
CWL=7
tCK(AVG)
Reserved
Reserved
ns
CL=6
CWL=5
tCK(AVG)
2.500
3.300
ns
CWL=6
tCK(AVG)
Reserved
Reserved
ns
CWL=7
tCK(AVG)
Reserved
Reserved
ns
CL=7
CWL=5
tCK(AVG)
Reserved
Reserved
ns
CWL=6
tCK(AVG)
1.875*
<2.5*
ns
CWL=7
tCK(AVG)
Reserved
Reserved
ns
CL=8
CWL=5
tCK(AVG)
Reserved
Reserved
ns
CWL=6
tCK(AVG)
1.875
<2.5
ns
CWL=7
tCK(AVG)
Reserved
Reserved
ns
CL=9
CWL=5
tCK(AVG)
Reserved
Reserved
ns
CWL=6
tCK(AVG)
Reserved
Reserved
ns
CWL=7
tCK(AVG)
1.500
<1.875
ns
CL=10
CWL=5
tCK(AVG)
Reserved
Reserved
ns
CWL=6
tCK(AVG)
Reserved
Reserved
ns
CWL=7
tCK(AVG)
1.500*
<1.875*
ns
Supported CL Settings
6,7,8,9,(10)
nCK
Supported CWL Settings
5,6,7
nCK
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
110
REV 1.1
08 / 2010
DDR3-1600MHz
Speed Bin
DDR3-1600
Unit
CL-nRCD-nRP
11-11-11 (-DI)
Parameter
Symbol
Min
Max
Internal read command to first data
tAA
13.750
(13.125)5,11
20.000
ns
ACT to internal read or write delay time
tRCD
13.750
(13.125)5,11
-
ns
PRE command period
tRP
13.750
(13.125)5,11
-
ns
ACT to ACT or REF command period
tRC
48.750
(48.125)5,11
-
ns
ACT to PRE command period
tRAS
35.000
9*tREFI
ns
CL=5
CWL =5
tCK(AVG)
3.000
3.300
ns
CWL =6
tCK(AVG)
Reserved
Reserved
ns
CWL =7
tCK(AVG)
Reserved
Reserved
ns
CWL =8
tCK(AVG)
Reserved
Reserved
ns
CL=6
CWL =5
tCK(AVG)
2.500
3.300
ns
CWL =6
tCK(AVG)
Reserved
Reserved
ns
CWL =7
tCK(AVG)
Reserved
Reserved
ns
CWL =8
tCK(AVG)
Reserved
Reserved
ns
CL=7
CWL =5
tCK(AVG)
Reserved
Reserved
ns
CWL =6
tCK(AVG)
1.875
<2.5
ns
CWL =7
tCK(AVG)
Reserved
Reserved
ns
CWL =8
tCK(AVG)
Reserved
Reserved
ns
CL=8
CWL =5
tCK(AVG)
Reserved
Reserved
ns
CWL =6
tCK(AVG)
1.875
<2.5
ns
CWL =7
tCK(AVG)
Reserved
Reserved
ns
CWL =8
tCK(AVG)
Reserved
Reserved
ns
CL=9
CWL =5
tCK(AVG)
Reserved
Reserved
ns
CWL =6
tCK(AVG)
Reserved
Reserved
ns
CWL =7
tCK(AVG)
1.500
<1.875
ns
CWL =8
tCK(AVG)
Reserved
Reserved
ns
CL=10
CWL =5
tCK(AVG)
Reserved
Reserved
ns
CWL =6
tCK(AVG)
Reserved
Reserved
ns
CWL =7
tCK(AVG)
1.500
<1.875
ns
CWL =8
tCK(AVG)
1.250
<1.5
ns
CL=11
CWL =5
tCK(AVG)
Reserved
Reserved
ns
CWL =6
tCK(AVG)
Reserved
Reserved
ns
CWL =7
tCK(AVG)
Reserved
Reserved
ns
CWL =8
tCK(AVG)
1.250*
<1.5*
ns
Supported CL Settings
6,7,8,9,10,(11)
nCK
Supported CWL Settings
5,6,7,8
nCK
*: Optional
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
111
REV 1.1
08 / 2010
Electrical Characteristics & AC Timing
Timing Parameter by Speed Bin (DDR3-800, 1066MHz)
Parameter
Symbol
DDR3-800
DDR3-1066
Units
Notes
Min.
Max.
Min.
Max.
Clock Timing
Minimum Clock Cycle Time (DLL off mode)
tCK (DLL_OFF)
8
-
8
-
ns
Average Clock Period
tCK(avg)
Refer to "Standard Speed Bins)
ps
Average high pulse width
tCH(avg)
0.47
0.53
0.47
0.53
tCK(avg)
Average low pulse width
tCL(avg)
0.47
0.53
0.47
0.53
tCK(avg)
Absolute Clock Period
tCK(abs)
Min.: tCK(avg)min + tJIT(per)min
Max.: tCK(avg)max + tJIT(per)max
ps
Absolute clock HIGH pulse width
tCH(abs)
0.43
-
0.43
-
tCK(avg)
Absolute clock LOW pulse width
tCL(abs)
0.43
-
0.43
-
tCK(avg)
Clock Period Jitter
JIT(per)
-100
100
-90
90
ps
Clock Period Jitter during DLL locking period
JIT(per, lck)
-90
90
-80
80
ps
Cycle to Cycle Period Jitter
tJIT(cc)
200
200
180
180
ps
Cycle to Cycle Period Jitter during DLL locking period
JIT(cc, lck)
180
180
160
160
ps
Duty Cycle Jitter
tJIT(duty)
-
-
-
-
ps
Cumulative error across 2 cycles
tERR(2per)
-147
147
-132
132
ps
Cumulative error across 3 cycles
tERR(3per)
-175
175
-157
157
ps
Cumulative error across 4 cycles
tERR(4per)
-194
194
-175
175
ps
Cumulative error across 5 cycles
tERR(5per)
-209
209
-188
188
ps
Cumulative error across 6 cycles
tERR(6per)
-222
222
-200
200
ps
Cumulative error across 7 cycles
tERR(7per)
-232
232
-209
209
ps
Cumulative error across 8 cycles
tERR(8per)
-241
241
-217
217
ps
Cumulative error across 9 cycles
tERR(9per)
-249
249
-224
224
ps
Cumulative error across 10 cycles
tERR(10per)
-257
257
-231
231
ps
Cumulative error across 11 cycles
tERR(11per)
-263
263
-237
237
ps
Cumulative error across 12 cycles
tERR(12per)
-269
269
-242
242
ps
Cumulative error across n = 13, 14 . . . 49, 50 cycles
tERR(nper)
tERR(nper)min = (1 + 0.68ln(n)) * tJIT(per)min
tERR(nper)max = (1 + 0.68ln(n)) * tJIT(per)max
ps
Data Timing
DQS, DQS# to DQ skew, per group, per access
tDQSQ
-
200
-
150
ps
DQ output hold time from DQS, DQS#
tQH
0.38
-
0.38
-
tCK(avg)
DQ low-impedance time from CK, CK#
tLZ(DQ)
-800
400
-600
300
ps
DQ high impedance time from CK, CK#
tHZ(DQ)
-
400
-
300
ps
Data setup time to DQS, DQS# referenced to Vih(ac) / Vil(ac) levels
tDS(base)
AC175
75
25
ps
Data setup time to DQS, DQS# referenced to Vih(ac) / Vil(ac) levels
tDS(base)
AC150
125
75
ps
Data hold time from DQS, DQS# referenced to Vih(dc) / Vil(dc) levels
tDH(base)
DC100
150
100
ps
DQ and DM Input pulse width for each input
tDIPW
600
490
ps
Data Strobe Timing
DQS,DQS# differential READ Preamble
tRPRE
0.9
Note 19
0.9
Note 19
tCK(avg)
DQS, DQS# differential READ Postamble
tRPST
0.3
Note 11
0.3
Note 11
tCK(avg)
DQS, DQS# differential output high time
tQSH
0.38
-
0.38
-
tCK(avg)
DQS, DQS# differential output low time
tQSL
0.38
-
0.38
-
tCK(avg)
DQS, DQS# differential WRITE Preamble
tWPRE
0.9
-
0.9
-
tCK(avg)
DQS, DQS# differential WRITE Postamble
tWPST
0.3
-
0.3
-
tCK(avg)
DQS, DQS# rising edge output access time from rising CK, CK#
tDQSCK
-400
400
-300
300
tCK(avg)
DQS and DQS# low-impedance time
(Referenced from RL - 1)
tLZ(DQS)
-800
400
-600
300
tCK(avg)
DQS and DQS# high-impedance time
(Referenced from RL + BL/2)
tHZ(DQS)
-
400
-
300
tCK(avg)
DQS, DQS# differential input low pulse width
tDQSL
0.45
0.55
0.45
0.55
tCK(avg)
DQS, DQS# differential input high pulse width
tDQSH
0.45
0.55
0.45
0.55
tCK(avg)
DQS, DQS# rising edge to CK, CK# rising edge
tDQSS
-0.25
0.25
-0.25
0.25
tCK(avg)
DQS, DQS# falling edge setup time to CK, CK# rising edge
tDSS
0.2
-
0.2
-
tCK(avg)
DQS, DQS# falling edge hold time from CK, CK# rising edge
tDSH
0.2
-
0.2
-
tCK(avg)
Command and Address Timing
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
112
REV 1.1
08 / 2010
DLL locking time
tDLLK
512
-
512
-
nCK
Internal READ Command to PRECHARGE Command delay
tRTP
tRTPmin.: max(4nCK, 7.5ns)
tRTPmax.: -
Delay from start of internal write
transaction to internal read command
tWTR
tWTRmin.: max(4nCK, 7.5ns)
tWTRmax.:
WRITE recovery time
tWR
15
-
15
-
ns
Mode Register Set command cycle time
tMRD
4
-
4
-
nCK
Mode Register Set command update delay
tMOD
tMODmin.: max(12nCK, 15ns)
tMODmax.:
ACT to internal read or write delay time
tRCD
PRE command period
tRP
ACT to ACT or REF command period
tRC
CAS# to CAS# command delay
tCCD
4
-
4
-
nCK
Auto precharge write recovery + precharge time
tDAL(min)
WR + roundup(tRP / tCK(avg))
nCK
Multi-Purpose Register Recovery Time
tMPRR
1
-
1
-
nCK
ACTIVE to PRECHARGE command period
tRAS
Standard Speed Bins
ACTIVE to ACTIVE command period for 1KB page size
tRRD
max(4nCK,
10ns)
-
max(4nCK,
7.5ns)
-
ACTIVE to ACTIVE command period for 2KB page size
tRRD
tRRDmin.: max(4nCK, 10ns)
tRRDmax.:
Four activate window for 1KB page size
tFAW
40
-
37.5
-
ns
Four activate window for 2KB page size
tFAW
50
-
50
-
ns
Command and Address setup time to CK, CK#
referenced to Vih(ac) / Vil(ac) levels
tIS(base)
200
-
125
-
ps
Command and Address hold time from CK, CK#
referenced to Vih(dc) / Vil(dc) levels
tIH(base)
275
-
200
-
ps
Command and Address setup time to CK, CK#
referenced to Vih(ac) / Vil(ac) levels
tIS(base) AC150
200+150
-
125+150
-
ps
Control and Address Input pulse width for each input
tIPW
900
-
780
-
ps
Calibration Timing
-
Power-up and RESET calibration time
tZQinit
512
-
512
-
nCK
Normal operation Full calibration time
tZQoper
256
-
256
-
nCK
Normal operation Short calibration time
tZQCS
64
-
64
-
nCK
Reset Timing
Exit Reset from CKE HIGH to a valid command
tXPR
tXPRmin.: max(5nCK, tRFC(min) + 10ns)
tXPRmax.: -
Self Refresh Timings
Exit Self Refresh to commands not requiring a locked DLL
tXS
tXSmin.: max(5nCK, tRFC(min) + 10ns)
tXSmax.: -
Exit Self Refresh to commands requiring a locked DLL
tXSDLL
tXSDLLmin.: tDLLK(min)
tXSDLLmax.: -
nCK
Minimum CKE low width for Self Refresh entry to exit timing
tCKESR
tCKESRmin.: tCKE(min) + 1 nCK
tCKESRmax.: -
Valid Clock Requirement after Self Refresh Entry (SRE)
or Power-Down Entry (PDE)
tCKSRE
tCKSREmin.: max(5 nCK, 10 ns)
tCKSREmax.: -
Valid Clock Requirement before Self Refresh Exit (SRX)
or Power-Down Exit (PDX) or Reset Exit
tCKSRX
tCKSRXmin.: max(5 nCK, 10 ns)
tCKSRXmax.: -
Power Down Timings
Exit Power Down with DLL on to any valid command;
Exit Precharge Power Down with DLL frozen to commands
not requiring a locked DLL
tXP
tXPmin.: max(3nCK, 7.5ns)
tXPmax.: -
Exit Precharge Power Down with DLL frozen to commands
requiring a locked DLL
tXPDLL
tXPDLLmin.: max(10nCK, 24ns)
tXPDLLmax.: -
CKE minimum pulse width
tCKE
tCKEmin.: max(3nCK 7.5ns)
tCKEmax.: -
tCKEmin.: max(3nCK 5.625ns)
tCKEmax.: -
Command pass disable delay
tCPDED
tCPDEDmin.: 1
tCPDEDmin.: -
nCK
Power Down Entry to Exit Timing
tPD
tPDmin.: tCKE(min)
tPDmax.: 9*tREFI
Timing of ACT command to Power Down entry
tACTPDEN
tACTPDENmin.: 1
tACTPDENmax.: -
nCK
Timing of PRE or PREA command to Power Down entry
tPRPDEN
tPRPDENmin.: 1
tPRPDENmax.: -
nCK
Timing of RD/RDA command to Power Down entry
tRDPDEN
tRDPDENmin.: RL+4+1
nCK
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
113
REV 1.1
08 / 2010
tRDPDENmax.: -
Timing of WR command to Power Down entry
(BL8OTF, BL8MRS, BC4OTF)
tWRPDEN
tWRPDENmin.: WL + 4 + (tWR / tCK(avg))
tWRPDENmax.: -
nCK
Timing of WRA command to Power Down entry
(BL8OTF, BL8MRS, BC4OTF)
tWRAPDEN
tWRAPDENmin.: WL+4+WR+1
tWRAPDENmax.: -
nCK
Timing of WR command to Power Down entry (BC4MRS)
tWRPDEN
tWRPDENmin.: WL + 2 + (tWR / tCK(avg))tWRPDENmax.: -
nCK
Timing of WRA command to Power Down entry
(BC4MRS)
tWRAPDEN
tWRAPDENmin.: WL + 2 +WR + 1
tWRAPDENmax.: -
nCK
Timing of REF command to Power Down entry
tREFPDEN
tREFPDENmin.: 1
tREFPDENmax.: -
nCK
Timing of MRS command to Power Down entry
tMRSPDEN
tMRSPDENmin.: tMOD(min)
tMRSPDENmax.: -
ODT Timings
ODT high time without write command or
with write command and BC4
ODTH4
ODTH4min.: 4
ODTH4max.: -
nCK
ODT high time with Write command and BL8
ODTH8
ODTH8min.: 6
ODTH8max.: -
nCK
Asynchronous RTT turn-on delay
(Power-Down with DLL frozen)
tAONPD
2
8.5
2
8.5
ns
Asynchronous RTT turn-off delay
(Power-Down with DLL frozen)
tAOFPD
2
8.5
2
8.5
ns
RTT turn-on
tAON
-400
400
-300
300
ps
RTT_Nom and RTT_WR turn-off time
from ODTLoff reference
tAOF
0.3
0.7
0.3
0.7
tCK(avg)
RTT dynamic change skew
tADC
0.3
0.7
0.3
0.7
tCK(avg)
Write Leveling Timings
First DQS/DQS# rising edge after
write leveling mode is programmed
tWLMRD
40
-
40
-
nCK
DQS/DQS# delay after write leveling mode is programmed
tWLDQSEN
25
-
25
-
nCK
Write leveling setup time from rising CK, CK#
crossing to rising DQS, DQS# crossing
tWLS
325
-
245
-
ps
Write leveling hold time from rising DQS, DQS#
crossing to rising CK, CK# crossing
tWLH
325
-
245
-
ps
Write leveling output delay
tWLO
0
9
0
9
ns
Write leveling output error
tWLOE
0
2
0
2
ns
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
114
REV 1.1
08 / 2010
Electrical Characteristics & AC Timing
Timing Parameter by Speed Bin (DDR3-1333, 1600MHz)
Parameter
Symbol
DDR3-1333
DDR3-1600
Units
Notes
Min.
Max.
Min.
Max.
Clock Timing
Minimum Clock Cycle Time (DLL off mode)
tCK (DLL_OFF)
8
-
8
-
ns
Average Clock Period
tCK(avg)
Refer to "Standard Speed Bins)
ps
Average high pulse width
tCH(avg)
0.47
0.53
0.47
0.53
tCK(avg)
Average low pulse width
tCL(avg)
0.47
0.53
0.47
0.53
tCK(avg)
Absolute Clock Period
tCK(abs)
Min.: tCK(avg)min + tJIT(per)min
Max.: tCK(avg)max + tJIT(per)max
ps
Absolute clock HIGH pulse width
tCH(abs)
0.43
-
0.43
-
tCK(avg)
Absolute clock LOW pulse width
tCL(abs)
0.43
-
0.43
-
tCK(avg)
Clock Period Jitter
JIT(per)
-80
80
-70
70
ps
Clock Period Jitter during DLL locking period
JIT(per, lck)
-70
70
-60
60
ps
Cycle to Cycle Period Jitter
tJIT(cc)
160
160
140
140
ps
Cycle to Cycle Period Jitter during DLL locking period
JIT(cc, lck)
140
140
120
120
ps
Duty Cycle Jitter
tJIT(duty)
-
-
-
-
ps
Cumulative error across 2 cycles
tERR(2per)
-118
118
-103
103
ps
Cumulative error across 3 cycles
tERR(3per)
-140
140
-122
122
ps
Cumulative error across 4 cycles
tERR(4per)
-155
155
-136
136
ps
Cumulative error across 5 cycles
tERR(5per)
-168
168
-147
147
ps
Cumulative error across 6 cycles
tERR(6per)
-177
177
-155
155
ps
Cumulative error across 7 cycles
tERR(7per)
-186
186
-163
163
ps
Cumulative error across 8 cycles
tERR(8per)
-193
193
-169
169
ps
Cumulative error across 9 cycles
tERR(9per)
-200
200
-175
175
ps
Cumulative error across 10 cycles
tERR(10per)
-205
205
-180
180
ps
Cumulative error across 11 cycles
tERR(11per)
-210
210
-184
184
ps
Cumulative error across 12 cycles
tERR(12per)
-215
215
-188
188
ps
Cumulative error across n = 13, 14 . . . 49, 50 cycles
tERR(nper)
tERR(nper)min = (1 + 0.68ln(n)) * tJIT(per)min
tERR(nper)max = (1 + 0.68ln(n)) * tJIT(per)max
ps
Data Timing
DQS, DQS# to DQ skew, per group, per access
tDQSQ
-
125
-
100
ps
DQ output hold time from DQS, DQS#
tQH
0.38
-
0.38
-
tCK(avg)
DQ low-impedance time from CK, CK#
tLZ(DQ)
-500
250
-450
225
ps
DQ high impedance time from CK, CK#
tHZ(DQ)
-
250
-
225
ps
Data setup time to DQS, DQS# referenced to Vih(ac) / Vil(ac) levels
tDS(base)
AC175
-
-
ps
Data setup time to DQS, DQS# referenced to Vih(ac) / Vil(ac) levels
tDS(base)
AC150
30
10
ps
Data hold time from DQS, DQS# referenced to Vih(dc) / Vil(dc) levels
tDH(base)
DC100
65
45
ps
DQ and DM Input pulse width for each input
tDIPW
400
-
360
ps
Data Strobe Timing
DQS,DQS# differential READ Preamble
tRPRE
0.9
Note 19
0.9
Note 19
tCK(avg)
DQS, DQS# differential READ Postamble
tRPST
0.3
Note 11
0.3
Note 11
tCK(avg)
DQS, DQS# differential output high time
tQSH
0.4
-
0.4
-
tCK(avg)
DQS, DQS# differential output low time
tQSL
0.4
-
0.4
-
tCK(avg)
DQS, DQS# differential WRITE Preamble
tWPRE
0.9
-
0.9
-
tCK(avg)
DQS, DQS# differential WRITE Postamble
tWPST
0.3
-
0.3
-
tCK(avg)
DQS, DQS# rising edge output access time from rising CK, CK#
tDQSCK
-255
255
-225
225
tCK(avg)
DQS and DQS# low-impedance time
(Referenced from RL - 1)
tLZ(DQS)
-500
250
-450
225
tCK(avg)
DQS and DQS# high-impedance time
(Referenced from RL + BL/2)
tHZ(DQS)
-
250
-
225
tCK(avg)
DQS, DQS# differential input low pulse width
tDQSL
0.45
0.55
0.45
0.55
tCK(avg)
DQS, DQS# differential input high pulse width
tDQSH
0.45
0.55
0.45
0.55
tCK(avg)
DQS, DQS# rising edge to CK, CK# rising edge
tDQSS
-0.25
0.25
-0.27
0.27
tCK(avg)
DQS, DQS# falling edge setup time to CK, CK# rising edge
tDSS
0.2
-
0.18
-
tCK(avg)
DQS, DQS# falling edge hold time from CK, CK# rising edge
tDSH
0.2
-
0.18
-
tCK(avg)
Command and Address Timing
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
115
REV 1.1
08 / 2010
DLL locking time
tDLLK
512
-
512
-
nCK
Internal READ Command to PRECHARGE Command delay
tRTP
tRTPmin.: max(4nCK, 7.5ns)
tRTPmax.: -
Delay from start of internal write
transaction to internal read command
tWTR
tWTRmin.: max(4nCK, 7.5ns)
tWTRmax.:
WRITE recovery time
tWR
15
-
15
-
ns
Mode Register Set command cycle time
tMRD
4
-
4
-
nCK
Mode Register Set command update delay
tMOD
tMODmin.: max(12nCK, 15ns)
tMODmax.:
ACT to internal read or write delay time
tRCD
PRE command period
tRP
ACT to ACT or REF command period
tRC
CAS# to CAS# command delay
tCCD
4
-
4
-
nCK
Auto precharge write recovery + precharge time
tDAL(min)
WR + roundup(tRP / tCK(avg))
nCK
Multi-Purpose Register Recovery Time
tMPRR
1
-
1
-
nCK
ACTIVE to PRECHARGE command period
tRAS
Standard Speed Bins
ACTIVE to ACTIVE command period for 1KB page size
tRRD
tRRDmin.: max(4nCK, 6ns)
tRRDmax.:
ACTIVE to ACTIVE command period for 2KB page size
tRRD
tRRDmin.: max(4nCK, 7.5ns)
tRRDmax.:
Four activate window for 1KB page size
tFAW
30
0
30
-
ns
Four activate window for 2KB page size
tFAW
45
0
40
-
ns
Command and Address setup time to CK, CK#
referenced to Vih(ac) / Vil(ac) levels
tIS(base)
65
-
45
-
ps
Command and Address hold time from CK, CK#
referenced to Vih(dc) / Vil(dc) levels
tIH(base)
140
-
120
-
ps
Command and Address setup time to CK, CK#
referenced to Vih(ac) / Vil(ac) levels
tIS(base) AC150
65+125
-
170
-
ps
Control and Address Input pulse width for each input
tIPW
620
-
560
-
ps
Calibration Timing
Power-up and RESET calibration time
tZQinit
512
-
512
-
nCK
Normal operation Full calibration time
tZQoper
256
-
256
-
nCK
Normal operation Short calibration time
tZQCS
64
-
64
-
nCK
Reset Timing
Exit Reset from CKE HIGH to a valid command
tXPR
tXPRmin.: max(5nCK, tRFC(min) + 10ns)
tXPRmax.: -
Self Refresh Timings
Exit Self Refresh to commands not requiring a locked DLL
tXS
tXSmin.: max(5nCK, tRFC(min) + 10ns)
tXSmax.: -
Exit Self Refresh to commands requiring a locked DLL
tXSDLL
tXSDLLmin.: tDLLK(min)
tXSDLLmax.: -
nCK
Minimum CKE low width for Self Refresh entry to exit timing
tCKESR
tCKESRmin.: tCKE(min) + 1 nCK
tCKESRmax.: -
Valid Clock Requirement after Self Refresh Entry (SRE)
or Power-Down Entry (PDE)
tCKSRE
tCKSREmin.: max(5 nCK, 10 ns)
tCKSREmax.: -
Valid Clock Requirement before Self Refresh Exit (SRX)
or Power-Down Exit (PDX) or Reset Exit
tCKSRX
tCKSRXmin.: max(5 nCK, 10 ns)
tCKSRXmax.: -
Power Down Timings
Exit Power Down with DLL on to any valid command;
Exit Precharge Power Down with DLL frozen to commands
not requiring a locked DLL
tXP
tXPmin.: max(3nCK, 6ns)
tXPmax.: -
tXPmin.: max(3nCK, 6ns)
tXPmax.: -
Exit Precharge Power Down with DLL frozen to commands
requiring a locked DLL
tXPDLL
tXPDLLmin.: max(10nCK, 24ns)
tXPDLLmax.: -
CKE minimum pulse width
tCKE
tCKEmin.: max(3nCK ,5.625ns)
tCKEmax.: -
tCKEmin.: max(3nCK ,5ns)
tCKEmax.: -
Command pass disable delay
tCPDED
tCPDEDmin.: 1
tCPDEDmin.: -
nCK
Power Down Entry to Exit Timing
tPD
tPDmin.: tCKE(min)
tPDmax.: 9*tREFI
Timing of ACT command to Power Down entry
tACTPDEN
tACTPDENmin.: 1
tACTPDENmax.: -
nCK
Timing of PRE or PREA command to Power Down entry
tPRPDEN
tPRPDENmin.: 1
tPRPDENmax.: -
nCK
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
116
REV 1.1
08 / 2010
Timing of RD/RDA command to Power Down entry
tRDPDEN
tRDPDENmin.: RL+4+1
tRDPDENmax.: -
nCK
Timing of WR command to Power Down entry
(BL8OTF, BL8MRS, BC4OTF)
tWRPDEN
tWRPDENmin.: WL + 4 + (tWR / tCK(avg))
tWRPDENmax.: -
nCK
Timing of WRA command to Power Down entry
(BL8OTF, BL8MRS, BC4OTF)
tWRAPDEN
tWRAPDENmin.: WL+4+WR+1
tWRAPDENmax.: -
nCK
Timing of WR command to Power Down entry (BC4MRS)
tWRPDEN
tWRPDENmin.: WL + 2 + (tWR / tCK(avg))tWRPDENmax.: -
nCK
Timing of WRA command to Power Down entry
(BC4MRS)
tWRAPDEN
tWRAPDENmin.: WL + 2 +WR + 1
tWRAPDENmax.: -
nCK
Timing of REF command to Power Down entry
tREFPDEN
tREFPDENmin.: 1
tREFPDENmax.: -
nCK
Timing of MRS command to Power Down entry
tMRSPDEN
tMRSPDENmin.: tMOD(min)
tMRSPDENmax.: -
ODT Timings
ODT high time without write command or
with write command and BC4
ODTH4
ODTH4min.: 4
ODTH4max.: -
nCK
ODT high time with Write command and BL8
ODTH8
ODTH8min.: 6
ODTH8max.: -
nCK
Asynchronous RTT turn-on delay
(Power-Down with DLL frozen)
tAONPD
2
8.5
2
8.5
ns
Asynchronous RTT turn-off delay
(Power-Down with DLL frozen)
tAOFPD
2
8.5
2
8.5
ns
RTT turn-on
tAON
-250
250
-225
225
ps
RTT_Nom and RTT_WR turn-off time
from ODTLoff reference
tAOF
0.3
0.7
0.3
0.7
tCK(avg)
RTT dynamic change skew
tADC
0.3
0.7
0.3
0.7
tCK(avg)
Write Leveling Timings
First DQS/DQS# rising edge after
write leveling mode is programmed
tWLMRD
40
-
40
-
nCK
DQS/DQS# delay after write leveling mode is programmed
tWLDQSEN
25
-
25
-
nCK
Write leveling setup time from rising CK, CK#
crossing to rising DQS, DQS# crossing
tWLS
195
-
165
-
ps
Write leveling hold time from rising DQS, DQS#
crossing to rising CK, CK# crossing
tWLH
195
-
165
-
ps
Write leveling output delay
tWLO
0
9
0
7.5
ns
Write leveling output error
tWLOE
0
2
0
2
ns
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
117
REV 1.1
08 / 2010
Jitter Notes
Specific Note a
Unit “tCK(avg)” represents the actual tCK(avg) of the input clock under operation. Unit “nCK” represents one clock cycle of
the input clock, counting the actual clock edges. ex) tMRD=4 [nCK] means; if one Mode Register Set command is regis-
tered at Tm, anther Mode Register Set command may be registered at Tm+4, even if (Tm+4-Tm) is 4 x tCK(avg) +
tERR(4per), min.
Specific Note b
These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc)
transition edge to its respective clock signal (CK/CK) crossing. The spec values are not affected by the amount of clock
jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as the setup and hold are relative to the clock signal crossing that latches the
command/address. That is, these parameters should be met whether clock jitter is present or not.
Specific Note c
These parameters are measured from a data strobe signal (DQS(L/U), DQS(L/U)) crossing to its respective clock signal
(CK, CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc), as
these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or
not.
Specific Note d
These parameters are measured from a data signal (DM(L/U), DQ(L/U)0, DQ(L/U)1, etc.) transition edge to its respective
data strobe signal (DQS(L/U), DQS(L/U)) crossing.
Specific Note e
For these parameters, the DDR3 SDRAM device supports tnPARAM [nCK] = RU{tPARAM[ns] / tCK(avg)[ns]}, which is in
clock cycles, assuming all input clock jitter specifications are satisfied. For example, the device will support tnRP =
RU{tRP/tCK(avg)}, which is in clock cycles, if all input clock jitter specifications are met. This means: For DDR3-800 6-6-6,
of which tRP = 15ns, the device will support tnRP = RU{tRP/tCK(avg)} = 6, as long as the input clock jitter specifications
are met, i.e. Precharge command at Tm and Active command at Tm+6 is valid even if (Tm+6-Tm) is less than 15ns due to
input clock jitter.
Specific Note f
When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(mper), act of the
input clock, where 2 <= m <=12. (output derating are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR3-800 SDRAM has tERR(mper),act,min = -172ps and tERR(mper),act,max
= 193ps, then tDQSCK,min(derated) = tDQSCK,min - tERR(mper),act,max = -400ps - 193ps = -593ps and
tDQSCK,max(derated) = tDQSCK,max - tERR(mper),act,min = 400ps + 172ps = 572ps. Similarly, tLZ(DQ) for DDR3-800
derates to tLZ(DQ),min(derated) = -800ps - 193ps = -993ps and tLZ(DQ),max(derated) = 400ps + 172ps = 572ps.
(Caution on the min/max usage!)
Note that tERR(mper),act,min is the minimum measured value of tERR(nper) where 2 <= n <= 12, and
tERR(mper),act,max is the maximum measured value of tERR(nper) where 2 <= n <= 12.
Specific Note g
When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(per),act of the
input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR3-800
SDRAM has tCK(avg),act=2500ps, tJIT(per),act,min = -72ps and tJIT(per),act,max = 93ps, then tRPRE,min(derated) =
tRPRE,min + tJIT(per),act,min = 0.9 x tCK(avg),act + tJIT(per),act,min = 0.9 x 2500ps - 72ps = 2178ps. Similarly,
tQH,min(derated) = tQH,min + tJIT(per),act,min = 0.38 x tCK(avg),act + tJIT(per),act,min = 0.38 x 2500ps - 72ps = 878ps.
(Caution on the min/max usage!)
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
118
REV 1.1
08 / 2010
Timing Parameter Notes
1. Actual value dependent upon measurement level definitions which are TBD.
2. Commands requiring a locked DLL are: READ (and RAP) is synchronous ODT commands.
3. The max values are system dependent.
4. WR as programmed in mode register.
5. Value must be rounded-up to next higher integer value.
6. There is no maximum cycle time limit besides the need to satisfy the refresh interval, tREFI.
7. For definition of RTT-on time tAON See “Timing Parameters”.
8. For definition of RTT-off time tAOF See “Timing Parameters”.
9. tWR is defined in ns, for calculation of tWRPDEN it is necessary to round up tWR / tCK to the next integer.
10. WR in clock cycles are programmed in MR0.
11. The maximum read post-amble is bounded by tDQSCK(min) plus tQSH(min) on the left side and tHZ(DQS)max on the
right side.
12. Output timing deratings are relative to the SDRAM input clock. When the device is operated with input clock jitter, this
parameter needs to be derated by TBD.
13. Value is only valid for RON34.
14. Single ended signal parameter.
15. tREFI depends on TOPER.
16. tIS(base) and tIH(base) values are for 1V/ns CMD/ADD single-ended slew rate and 2V/ns CK, CK differential slew
rate. Note for DQ and DM signals, VREF(DC)=VRefDQ(DC). For input only pins except RESET,
VRef(DC)=VRefCA(DC).
17. tDS(base) and tDH(base) values are for 1V/ns DQ single-ended slew rate and 2V/ns DQS, DQS differential slew rate.
Note for DQ and DM signals, VREF(DC)=VRefDQ(DC). For input only pins except RESET, VRef(DC)=VRefCA(DC).
18. Start of internal write transaction is defined as follows:
For BL8 (fixed by MRS and on-the-fly): Rising clock edge 4 clock cycles after WL.
For BC4 (on-the-fly): Rising clock edge 4 clock cycles after WL.
For BC4 (fixed by MRS): Rising clock edge 2 clock cycles after WL.
19. The maximum preamble is bound by tLZ(DQS)max on the left side and tDQSCK(max) on the right side.
20. CKE is allowed to be registered low while operations such as row activation, precharge, autoprecharge or refresh are
in progress, but power-down IDD spec will not be applied until finishing those operations.
21. Although CKE is allowed to be registered LOW after a REFRESH command once tREFPDEN(min) is satisfied, there
are cases where additional time such as tXPDLL(min) is also required.
22. Defined between end of MPR read burst and MRS which reloads MPR or disables MPR function.
23. One ZQCS command can effectively correct a minimum of 0.5% (ZQ Correction) of RON and RTT impedance error
within 64 nCK for all speed bins assuming the maximum sensitivities specified in the “Output Driver Voltage and
Temperature Sensitivity” and “ODT Voltage and Temperature Sensitivity” tables. The appropriate interval between
ZQCS commands can be determined from these tables and other application-specific parameters.
One method for calculating the interval between ZQCS commands, given the temperature (Tdriftrate) and voltage
(Vdriftrate) drift rates that the SDRAM is subject to in the application, is illustrated. the interval could be defined by the
following formula: ZQCorrection / [(TSens x Tdriftrate) + (VSens x Vdriftrate)] where TSens = max(dRTTdT,
dRONdTM) and VSens = max(dRTTdV, dRONdVM) define the SDRAM temperature and voltage sensitivities.
For example, if TSens = 1.5%/C, VSens = 0.15%/mV, Tdriftrate = 1 C/sec and Vdriftrate = 15mV/sec, then the interval
between ZQCS commands is calculated as 0.5 / [(1.5x1)+(0.15x15)] = 0.133 ~ 128ms
24. n = from 13 cycles to 50 cycles. This row defines 38 parameters.
25. tCH(abs) is the absolute instantaneous clock high pulse width, as measured from one rising edge to the following
falling edge.
26. tCL(abs) is the absolute instantaneous clock low pulse width, as measured from one falling edge to the following rising
edge.
27. The tIS(base) AC150 specifications are adjusted from the tIS(base) specification by adding an additional 100ps of
derating to accommodate for the lower ultimate threshold of 150mV and another 25ps to account for the earlier
reference point [(175mV - 150mV) / 1V/ns].
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
119
REV 1.1
08 / 2010
Address / Command Setup, Hold, and De-rating
For all input signals the total tIS (setup time) and tIH (hold time) required is calculated by adding the data sheet tIS(base)
and tIH(base) and tIH(base) value to the delta tIS and delta tIH derating value respectively.
Example: tIS (total setup time) = tIS(base) + delta tIS
Setup (tIS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of Vref(dc) and the first
crossing of VIH(ac)min. Setup (tIS) nominal slew rate for a falling signal is defined as the slew rate between the last
crossing of Vref(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line
between shaded „Vref(dc) to ac region‟, use nominal slew rate for derating value. If the actual signal is later than the
nominal slew rate line anywhere between shaded „Vref(dc) to ac region‟, the slew rate of the tangent line to the actual signal
from the ac level to dc level is used for derating value.
Hold (tIH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the
first crossing of Vref(dc). Hold (tIH) nominal slew rate for a falling signal is defined as the slew rate between the last
crossing of VIH(dc)min and the first crossing of Vref(dc). If the actual signal is always later than the nominal slew rate line
between shaded „dc to Vref(dc) region‟, use nominal slew rate for derating value. If the actual signal is earlier than the
nominal slew rate line anywhere between shaded „dc to Vref(dc) region‟, the slew rate of a tangent line to the actual signal
from the dc level to Vref(dc) level is used for derating value. For a valid transition the input signal has to remain
above/below VIH/IL(ac) for some time tVAC. Although for slow slew rates the total setup time might be negative (i.e. a valid
input signal will not have reached VIH/IL(ac) at the time of the rising clock transition) a valid input signal is still required to
complete the transition and reach VIH/IL(ac).
ADD/CMD Setup and Hold Base-Values for 1V/ns
Unit [ps]
DDR3-800
DDR3-1066
DDR3-1333
DDR3-1600
reference
(-AC/-AD)
(-BE)
(-CG)
(-DI)
tIS(base)
200
125
65
45
VIH/L(ac)
tIH(base)
275
200
140
120
VIH/L(dc)
tIH(base) AC150
350
275
190
170
VIH/L(dc)
Note:
1. (ac/dc referenced for 1V/ns DQ-slew rate and 2V/ns DQS slew rate.
2. The tIS(base) AC150 specifications are adjusted from the tIS(base) specification by adding an additional 100ps of
derating to accommodate for the lower alternate threshold of 150mV and another 25ps to account for the earlier reference
point [(175mV - 150mV) / 1V/ns].
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
120
REV 1.1
08 / 2010
De-rating values DDR3- 800/1066/1333/1600 tIS/tIH (AC175)
De-rating values DDR3- 800/1066/1333/1600 tIS/tIH (AC150)
Required time tVAC above VIH(ac) {below VIL(ac)} for valid transition
Slew Rate [V/ns]
tVAC@175mV [ps]
tVAC@175mV [ps]
min
max
min
max
>2.0
75
-
175
-
2
57
-
170
-
1.5
50
-
167
-
1
38
-
163
-
0.9
34
-
162
-
0.8
29
-
161
-
0.7
22
-
159
-
0.6
13
-
155
-
0.5
0
-
150
-
<0.5
0
-
150
-
D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH
288 50 88 50 88 50 96 58 104 66 112 74 120 84 128 100
1.5 59 34 59 34 59 34 67 42 75 50 83 58 91 68 99 84
10000008816 16 24 24 32 34 40 50
0.9 -2 -4 -2 -4 -2 -4 6 4 14 12 22 20 30 30 38 46
0.8 -6 -10 -6 -10 -6 -10 2 -2 10 618 14 26 24 34 40
0.7 -11 -16 -11 -16 -11 -16 -3 -8 5 0 13 821 18 29 34
0.6 -17 -26 -17 -26 -17 -26 -9 -18 -1 -10 7 -2 15 823 24
0.5 -35 -40 -35 -40 -35 -40 -27 -32 -19 -24 -11 -16 -2 -6 510
0.4 -62 -60 -62 -60 -62 -60 -54 -52 -46 -44 -38 -36 -30 -26 -22 -10
1.2 V/ns
DQ Slew rate (V/ns)
4.0 V/ns
3.0 V/ns
DQS,  Differential Slew Rate
Delta tIS, Delta tIH derating in AC/DC based
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4 V/ns
1.0 V/ns
D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH D tIS D tIH
275 50 75 50 75 50 83 58 91 66 99 74 107 84 115 100
1.5 50 34 50 34 50 34 58 42 66 50 74 58 82 68 90 84
10000008816 16 24 24 32 34 40 50
0.9 0 -4 0-4 0-4 8 4 16 12 24 20 32 30 40 46
0.8 0 -10 0 -10 0 -10 8 -2 16 624 14 32 24 40 40
0.7 0 -16 0 -16 0 -16 8 -8 16 024 832 18 40 34
0.6 -1 -26 -1 -26 -1 -26 7 -18 15 -10 23 -2 31 839 24
0.5 -10 -40 -10 -40 -10 -40 -2 -32 6 -24 14 -16 22 -6 30 10
0.4 -25 -60 -25 -60 -25 -60 -17 -52 -9 -44 -1 -36 7 -26 15 -10
1.0 V/ns
1.2 V/ns
DQ Slew rate (V/ns)
4.0 V/ns
3.0 V/ns
DQS,  Differential Slew Rate
Delta tIS, Delta tIH derating in AC/DC based
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4 V/ns
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
121
REV 1.1
08 / 2010
Data Setup, Hold, and Slew Rate De-rating
For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the data sheet tDH(base)
and tDH(base) value to the delta tDS and delta tDH derating value respectively.
Example: tDS (total setup time) = tDS(base) + delta tDS
Setup (tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of Vref(dc) and the
first crossing of VIH(ac)min. Setup (tDS) nominal slew rate for a falling signal is defined as the slew rate between the last
crossing of Vref(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line
between shaded „Vref(dc) to ac region‟, use nominal slew rate for derating value. If the actual signal is later than the
nominal slew rate line anywhere between shaded „Vref(dc) to ac region‟, the slew rate of the tangent line to the actual signal
from the ac level to dc level is used for derating value.
Hold (tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the
first crossing of Vref(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last
crossing of VIH(dc)min and the first crossing of Vref(dc). If the actual signal is always later than the nominal slew rate line
between shaded „dc level to Vref(dc) region‟, use nominal slew rate for derating value. If the actual signal is earlier than the
nominal slew rate line anywhere between shaded „dc to Vref(dc) region‟, the slew rate of a tangent line to the actual signal
from the dc level to Vref(dc) level is used for derating value.
For a valid transition the input signal has to remain above/below VIH/IL(ac) for some time tVAC.
Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(ac)
at the time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).
For slew rates in between the values listed in the following tables, the derating values may be obtained by linear
interpolation.
These values are typically not subject to production test. They are verified by design and characterization.
Data Setup and Hold Base-Values
Unit [ps]
DDR3-800
(-AC/-AD)
DDR3-1066
(-BE)
DDR3-1333
(-CG)
DDR3-1600
(-DI)
reference
tDS(base)
75
25
-
-
VIH/L(ac)
tDS(AC150)
125
75
30
10
VIH/L(ac)
tDH(base)
150
100
65
45
VIH/L(dc)
Note: ac/dc referenced for 1V/ns DQ-slew rate and 2V/ns DQS slew rate
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
122
REV 1.1
08 / 2010
De-rating values DDR3- 800/1066/1333/1600 tDS/tDH (AC175)
De-rating values DDR3- 800/1066/1333/1600 tDS/tDH (AC150)
Required time tVAC above VIH(ac) {below VIL(ac)} for valid transition
Slew Rate [V/ns]
DDR3-800/1066 (AC175)
DDR3-1333/1600 (AC150)
tVAC[ps]
tVAC[ps]
min
max
min
max
>2.0
75
-
175
-
2
57
-
170
-
1.5
50
-
167
-
1
38
-
163
-
0.9
34
-
162
-
0.8
29
-
161
-
0.7
22
-
159
-
0.6
13
-
155
-
0.5
0
-
155
-
<0.5
0
-
150
-
D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH
288 50 88 50 88 50 - - - - - - - - - -
1.5 59 34 59 34 59 34 67 42 - - - - - - - -
10000008816 16 ------
0.9 - - -2 -4 -2 -4 6 4 14 12 22 20 - - - -
0.8 - - - - -6 -10 2 -2 10 618 14 26 24 - -
0.7 - - - - - - -3 -8 5 0 13 821 18 29 34
0.6 - - - - - - - - -1 -10 7 -2 15 823 24
0.5 - - - - - - - - - - -11 -16 -2 -6 510
0.4 - - - - - - - - - - - - -30 -26 -22 -10
1.2 V/ns
DQ Slew rate (V/ns)
4.0 V/ns
3.0 V/ns
DQS,  Differential Slew Rate
Delta tDS, Delta tDH derating in AC/DC based
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4 V/ns
1.0 V/ns
D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH D tDS D tDH
275 50 75 50 75 50 - - - - - - - - - -
1.5 50 34 50 34 50 34 58 42 - - - - - - - -
10000008816 16 ------
0.9 - - 0 -4 0-4 8 4 16 12 24 20 - - - -
0.8 - - - - 0 -10 8 -2 16 624 14 32 24 - -
0.7 - - - - - - 8 -8 16 024 832 18 40 34
0.6 - - - - - - - - 15 -10 23 -2 31 839 24
0.5 - - - - - - - - - - 14 -16 22 -6 30 10
0.4 - - - - - - - - - - - - 7 -26 15 -10
1.0 V/ns
1.2 V/ns
DQ Slew rate (V/ns)
4.0 V/ns
3.0 V/ns
DQS,  Differential Slew Rate
Delta tDS, Delta tDH derating in AC/DC based
2.0 V/ns
1.8 V/ns
1.6 V/ns
1.4 V/ns
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
123
REV 1.1
08 / 2010
Package Dimensions (x4; 78 balls; 0.8mmx0.8mm Pitch; BGA)
0.8
6.4
0.8
9.0 +/- 0.1
10.5 +/- 0.1
Pin A1 Index
Pin A1 Index
Min. 0.25
Max. 0.40
Max. 1.20
TOP VIEWBOTTOM VIEW
9.6
Min. 0.40
Max. 0.50
78Balls
Units: mm
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
124
REV 1.1
08 / 2010
Package Dimensions (x8; 78 balls; 0.8mmx0.8mm Pitch; BGA)
0.8
6.4
0.8
9.0 +/- 0.1
10.5 +/- 0.1
Pin A1 Index
Pin A1 Index
Min. 0.25
Max. 0.40
Max. 1.20
TOP VIEWBOTTOM VIEW
9.6
Min. 0.40
Max. 0.50
78Balls
Units: mm
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
125
REV 1.1
08 / 2010
Package Dimensions (x16; 96 balls; 0.8mmx0.8mm Pitch; BGA)
0.8
6.4 9.0 +/- 0.1
13.0 +/- 0.1
Pin A 1 Index
Pin A 1 Index
Min. 0. 25
Max. 0.40
Max .
TOP VIEWBOTTOM VIEW
12
Min. 0. 40
Max. 0.50
96 Balls
Units: mm
0.8
1.20
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
126
REV 1.1
08 / 2010
Revision Log
Rev
Date
Modification
0.1
01/2010
Preliminary Release
1.0
04/2010
Official revision released
1.1
08/2010
Add DDR3L (VDD=1.35V)
2Gb DDR3 SDRAM B-Die
NT5CB512M4BN / NT5CB256M8BN / NT5CB128M16BP
NT5CC512M4BN / NT5CC256M8BN / NT5CC128M16BP
127
REV 1.1
08 / 2010
®
Nanya Technology Corporation.
All rights reserved.
Printed in Taiwan, R.O.C., 2006
The following are trademarks of NANYA TECHNOLOGY CORPORATION in R.O.C, or other countries, or both.
NANYA and NANYA logo
Other company, product and service names may be trademarks or service marks of others.
NANYA TECHNOLOGY CORPORATION (NTC) reserves the right to make changes without notice. NTC warrants
performance of its semiconductor products and related software to the specifications applicable at the time of sale in
accordance with NTC‟s standard warranty. Testing and other quality control techniques are utilized to the extent NTC
deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed,
except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property
or environmental damage (“Critical Applications”).
NTC SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTEND, AUTHORIZED, OR WARRANTED TO BE
SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL
APPLICATIONS.
Inclusion of NTC products in such applications is understood to be fully at the risk of the customer. Use of NTC products in
such applications requires the written approval of an appropriate NTC officer. Question concerning potential risk
applications should be directed to NTC through a local sales office.
In order to minimize risks associated with the customer‟s applications, adequate design and operating safeguards should
be provided by customer to minimize the inherent or procedural hazards.NTC assumes no liability of applications
assistance, customer product design, software performance, or infringement of patents or services described herein. Nor
does NTC warrant or represent that any license, either express or implied, is granted under any patent right, copyright,
mask work right, or other intellectual property right of NTC covering or relating to any combination, machine, or process in
which such semiconductor products or services might be or are used.
NANYA TECHNOLOGY CORPORATION
HWA YA Technology Park
669, FU HSING 3rd Rd., Kuei-Shan, Tao-Yuan, Taiwan, R.O.C.
The NANYA TECHNOLOGY CORPORATION
Home page can be found at http:\\www.nanya.com