3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight HSHM Series
• Up to 5 Gb/s data rates
• Low crosstalk at high frequencies
• 50/100 Ω (single-ended /differential) impedance
• Modular/scalable format IEC 61076-4-101
• 101 mated lines per linear inch
• Integrated guide pin
• End-to-end stackable with 8 row 3M™ MetPak™ CP2,
HM and HSHM headers
• See the Regulatory Information Appendix (RIA) in
the “RoHS compliance” section of
www.3mconnector.com for compliance information
Date Modifi ed: October 22, 2010 TS-2077-B
Sheet 1 of 3
Physical
Insulation:
Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact:
Material: Copper Alloy
Plating: See Ordering Information
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield
Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield
Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield
Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield
Mate/Unmate Cycles: 250
Application: This module is not suitable for stand-alone use. (Refer to IEC-61076-4-101)
Electrical:
Data Rate: 5 Gb/s
Characteristic Impedance: 50 Ω Single-ended, 100 Ω Differential
Current Rating (Fully Loaded): 1 A @ 70° C Signal
Insulation Resistance: 104 MΩ @ 100 VDC
Withstanding Voltage: 750 Vrms
Environmental
Temperature Rating: -55° C to 125° C
UL File No.: E68080 MetPak is a trademark of 3M Company.
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight HSHM Series
TS-2077-B
Sheet 2 of 3
Ordering Information
HSHM-H200DEX-8CPX- XXXXX
mm
(Inch)
Tolerance Unless Noted
0 0.0 0.00
mm ±3 ±0.3 ±0.13
( ) Dimensions used for
Reference Only
denotes shield column (tail only) omitted for the row
differential pair part
ROW F
ROW E
ROW D
ROW C
ROW B
ROW A
ROW Z
Pin positions
Shield positions
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Row differential configuration
shown with protective caps*
* Caps to be removed after press-fit installation process
DIM A = Pin mating length
DIM B = Shield tail length
DIM C = Pin tail length
Coaxial, column differential and stripline configuration
shown with protective caps*
HSHM-HXXXXX-8XPX-XXXXX
REV X XXYY
HSHM-HXXXXX-8XPX-XXXXX
REV X XXYY
15.15
.596
18.00
.709
2.00
.079
2.00
.079
2.00
.079
2.00
.079
48.00
1.890
ROW G
ROW H
ROW I
4.50
.177
1.50
.059
21.40
.843
17.85
.703
5.00
.197
13.40
.528
4.50
.177
DIM C
DIM A
DIM B
Interstitial
ground
contacts Signal
contacts
High Speed Option:
4 = Coaxial, column differential and
stripline (75 Ω) applications
5 = Row differential applications
Tail Length:
1 = 4.4 mm pin and 3.5 mm shield
2 = 2 mm pin and 2 mm shield
Standard Configuration
DIM A = 5.3 mm for rows A through H
For non--standard configurations contact sales representative
(rows I and Z not loaded)
Plating μm [ μ” ]:
TG30 = 0.76 [30] Min. Au Contact Area
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Standard Option
TG30L = 0.76 [30] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Typically higher make order quantities as compared to TG30.
TG50 = 1.27 [50] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight HSHM Series
TS-2077-B
Sheet 3 of 3
Recommended PCB hole mounting pattern for coaxial,
column differential and stripline applications
Recommended PCB hole mounting pattern for row
differential applications
(Same geometry as left view without the ground vias)
Plated thru holes
See hole plating table
0.10 A B
2.00
1.00
2.00
1.00
48.00
ABCDE A
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ABCDE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
FGH
FGH
DIM. D
14.00
M
Ø
Ø
Hole Plating Table mm
Finished Hole Dia. “D” Cu. Thickness SnPb Thickness Drilled Hole Dia.
0.457 - 0.559 [.0180 - .0220] 0.025 - 0.045 [.0010 - .0018] 0.008 -0.018 [.0003 - .0007] 0.584 - 0.625 [.0230 - .0246]
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2010. All rights reserved.
RIA-2217B-E
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3Mconnector.com 3M is a trademark of 3M Company.
