EBWT12-A-eHealth - Bluegiga Technologies

WT12 EVALUATION KIT

DATA SHEET

Monday, 09 September 2013

Version 1.7

Bluegiga Technologies Oy

Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual.

Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications

detailed here at any time without notice and does not make any commitment to update the information

contained here. Bluegiga’s products are not authorized for use as critical components in life support devices

or systems.

The WRAP, Bluegiga Access Server, Access Point and iWRAP are registered trademarks of Bluegiga

Technologies.

The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies.

All other trademarks listed herein are owned by their respective owners.

Bluegiga Technologies Oy

VERSION HISTORY

Version

Comment

1.0

MSa

1.1

1.2

1.3

MSa

1.4

MSa

1.5

MSa

1.6

MSa

1.7

Table 2 corrected

Bluegiga Technologies Oy

TABLE OF CONTENTS

WT12 Evaluation Kit .............................................................................................................................................1

Data Sheet ............................................................................................................................................................1

1 Introduction ....................................................................................................................................................5

2 Physical outlook .............................................................................................................................................6

3 Schematics ....................................................................................................................................................7

4 Assembly .......................................................................................................................................................7

5 Gerber ...........................................................................................................................................................7

6 SPI (J1) interface ...........................................................................................................................................8

7 GPIO (J2) interface........................................................................................................................................9

8 PIO SELECT (J3) ....................................................................................................................................... 10

9 RESET (J4) ................................................................................................................................................ 10

10 DSR (J5) ................................................................................................................................................ 10

11 Speaker JACK (J6) ................................................................................................................................ 11

12 Microphone JACK (J7) ........................................................................................................................... 11

13 SIG Select (J8) ...................................................................................................................................... 11

14 RS-232 (J9) DTE interface .................................................................................................................... 12

15 USB (J10) interface ............................................................................................................................... 13

16 Power supply (J11) ................................................................................................................................ 13

17 Power supply (J12) ................................................................................................................................ 13

18 Contact Information ............................................................................................................................... 14

Bluegiga Technologies Oy

1 Introduction

WT12 Development Kit Contents:

 WT12 development board containing:

o WT12 Bluetooth Module

o RS232 and USB interfaces

o PCM codec and 3.5mm audio jacks

o 16 pin IO header

o Unregulated power supply input (5-9V)

o Debug connector for firmware updates

o 3,5mm audio jacks for speaker and microphone connection

 RS232 cable

 Debug cable for firmware updates

 Documentation

 Preinstalled with latest iWRAP Bluetooth software

Bluegiga Technologies Oy

2 Physical outlook

Figure 1: WT12 Development Kit

Bluegiga Technologies Oy

Page 7 of 14

3 Schematics

Schematics of WT12 Evaluation Kit can be found from the CD delivered with the package or alternatively

downloaded from http://techforum.bluegiga.com

4 Assembly

Figure 2: WT12 Evaluation Kit assembly

5 Gerber

Gerber of WT12 Evaluation Kit can be found from the CD delivered with the package or alternatively

downloaded form http://techforum.bluegiga.com.

Bluegiga Technologies Oy

Page 8 of 14

6 SPI (J1) interface

SPI interface pin configuration is show in Table 2. The physical interface is 2X3 pin header (AMP146134-2).

PIN Name:

No.:

I/O:

Description:

MISO

3.3 V

POWER

3.3 V power supply input

CLK

MOSI

CSB

GND

Table 1: SPI Interface PIN description

Bluegiga Technologies Oy

Page 9 of 14

7 GPIO (J2) interface

General purpose interface pin configuration is show in Table 2. The physical interface is 2X8 pin header

(AMP146134-7).

PIN Name:

No.:

I/O:

Description:

RESET

Reset

3.3 V

POWER

Regulated power supply output

(3.3 V)

PIO2

I/O

Programmable IO number 2

PIO3

I/O

Programmable IO number 3

PIO4

I/O

Programmable IO number 4

PIO5

I/O

Programmable IO number 5

PIO6

I/O

Programmable IO number 6

PIO7

I/O

Programmable IO number 7

RTS

UART RTS

CTS

UART CTS

GND

TxD

UART TX

RxD

UART RX

GND

POWER

Unregulated power supply

input/output

(5-9 V)

Table 2: GPIO interface PIN description

Bluegiga Technologies Oy

Page 10 of 14

8 PIO SELECT (J3)

This switch toggles PIO2 to PIO7 signal connections between J2 connector and LED/USB/UART interfaces.

Note: ‘Top’ and ‘bottom’ positions refer to viewing WT12 Evaluation Kit from top side as seen in Figure 2.

 Top position must be used when WT12 module is interfaced trough J2 connector.

 Bottom position is used when WT12 module is interfaced trough the DB9 RS232 connector or if USB

port or if link state LED is used.

J3 Switch top position:

 PIO2 connects to pin 3 on the J2 interface

 PIO3 connects to pin 4 on the J2 interface

 PIO4 connects to pin 5 on the J2 interface

 PIO5 connects to pin 6 on the J2 interface

 PIO6 connects to pin 7 on the J2 interface

 PIO7 connects to pin 8 on the J2 interface

J3 Switch bottom position:

 PIO2 connects to USB_IO1

 PIO3 connects to nDTR-UART

 PIO4 connects to nCD-UART

 PIO5 connects to nDSR-MUX

 PIO6 connects to VBUS

 PIO7 connects to blue LED on the board marked with PIO7

9 RESET (J4)

The RESET button resets the module using the reset pin on the WT12.

10 DSR (J5)

The DSR button is connected to PIO5 pin on the WT12. Thus, when you want to use the DSR signal, please

refer to the iWRAP 2.1.0 manual. The use of DSR signal is described under SET CONTROL ESCAPE

chapter.

Bluegiga Technologies Oy

Page 11 of 14

11 Speaker JACK (J6)

Connect your generic PC headset’s 3,5mm speaker plug here.

12 Microphone JACK (J7)

Connect your generic PC headset’s 3,5mm headphone plug here.

13 SIG Select (J8)

This switch toggles nCTS and RxD signals connection between J2 connector and DB9 RS232 connector.

Note: ‘Top’ and ‘bottom’ positions refer to viewing WT12 Evaluation Kit from top side as seen in Figure 2.

 Top position must be used when external WT12 module’s nCTS and RxD pins are interfaced trough

J2 connector.

 Bottom position must be used when WT12 is interfaced trough the DB9 RS232 connector.

J8 Switch top position:

 nCTS connects to pin 10 on the GPIO (J2) interface

 RxD connects to pin 14 on the GPIO (J2) interface

J8 Switch bottom position:

 nCTS connects to nCTS-UART

 RxD connects to RXD-UART

Bluegiga Technologies Oy

Page 12 of 14

14 RS-232 (J9) DTE interface

RS-232 interface PIN configuration is shown in Table 1. The physical interface is D9-male connector

(AMP747840-4).

PIN Name:

No.:

I/O:

Description:

Not connected

RxD

TxD

DTR

DTR on

GND

Ground

Not connected

RTS

CTS

Not connected

Table 3: RS232 PIN configuration

Bluegiga Technologies Oy

Page 13 of 14

15 USB (J10) interface

J10 connector is a standard USB B receptacle connector.

16 Power supply (J11)

This connector is used with the 5V power supply delivered with the evaluation kit. Diameter 6.0mm, inner pin

diameter 2.0mm.

17 Power supply (J12)

This connector can be used for external power supply. Power supply must be 5-9V unregulated.

Bluegiga Technologies Oy

Page 14 of 14

18 Contact Information

Sales: sales@bluegiga.com

Technical support: http://techforum.bluegiga.com

Orders: orders@bluegiga.com

WWW: www.bluegiga.com

www.bluegiga.hk

Head Office / Finland:

Phone: +358-9-4355 060

Fax: +358-9-4355 0660

Sinikalliontie 5A

02630 ESPOO

FINLAND

Postal address / Finland:

P.O. BOX 120

02631 ESPOO

FINLAND

Sales Office / USA:

Phone: +1 770 291 2181

Fax: +1 770 291 2183

Bluegiga Technologies, Inc.

3235 Satellite Boulevard, Building 400, Suite 300

Duluth, GA, 30096, USA

Sales Office / Hong-Kong:

Phone: +852 3182 7321

Fax: +852 3972 5777

Bluegiga Technologies, Inc.

19/F Silver Fortune Plaza, 1 Wellington Street,

Central Hong Kong

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Bluegiga Technologies:

EBWT12-A EBWT12-A-eHealth