Advanced Power
Electronics Corp.
FEATURES DESCRIPTION
1.5V Maximum Dropout at Full Load Current
Fast Transient Response
Output Current Limiting
Built-in Thermal Shutdown
Good Noise Rejection
3-Terminal Adjustable or Fixed 1.5V, 1.8V,
1.9V, 2.5V, 3.3V, 5.0V
Packages : SOT-223, TO-252, SOT-89.
Halogen Free Product
Data and specifications subject to change without notice
201205097
APE1117
TYPICAL APPLICATION
1
1A LOW DROPOUT LINEAR REGULATOR
APE1117 is a low dropout positive adjustable or fixed-
mode regulator with minimum of 1A output current
capability. The product is specifically designed to provide
well-regulated supply for low voltage IC applications such as
high-speed bus termination and low current 3.3V logic
supply. APE1117 is also well suited for other applications
such as VGA cards. APE1117 is guaranteed to have lowe
r
than 1.4V dropout at full load current making it ideal to
provide well-regulated outputs of 1.25 to 5.0 with 6.4V to
12V input supply.
C2
100uF
5V
3.3V/1A
Tab is Vout
Vin
Vout
GND
C1
100uF
( 5V/3.3V fixed output )
R1
121
R2
121
C2
100uF
5V
2.5V/1A
Tab is Vout
Vin
Vout
Adj
C1
100uF
o
V
( 5V/2.5V ADJ output )
)
1
2
REFoR
R
(1 VV +∗=
Note:
Ω
Ω
Advanced Power
Electronics Corp. APE1117
ABSOLUTE MAXIMUM RATINGS (at TA=25°C)
DC Supply Voltage(VIN) ---------------------------------- -0.3V to 15V
Power Dissipation(PD)Note @TA=25oC, TJ=125oC
SOT-223 -----
-
850mW
SOT-89 -------
-
330mW
TO-252 -------
-
1050mW
Storage Temperature Range(TST) --------------------
-
-65°C To 150°C
Operating Junction Temperature Range(TJ) -------
-
-40°C To 125°C
Maximum Junction Temperature(TMJ) ---------------
-
150°C
Thermal Resistance from Junction to Case(Rthjc)
SOT-223 -----
-
15°C/W
SOT-89 -------
-
100°C/W
TO-252 -------
-
10°C/W
SOT-223 -----
-
117°C/W
SOT-89 -------
-
300°C/W
TO-252 -------
-
92°C/W
Note. No heat sink; No air flow)
ORDERING/PACKAGE INFORMATION
ELECTRICAL SPECIFICATIONS
(TA=25°C, unless otherwise specified)
Parameter MIN TYP MAX UNITS
Operation Input Voltage 2.75 - 12 V
Dropout Voltage(VIN-VOUT)
APE1117X-
ADJ/15/18/25
/33/50
IOUT = 1A , δVOUT=1%VOUT - 1.3 1.5 V
Current Limit
APE1117X-
ADJ/15/18/25
/33/50
(VIN-VOUT) = 3V 1.1 - - A
Minimum Load Current APE1117X-XX 0°C≦TJ≦125°C - 5 10 mA
IOUT=10mA, VOUT+1.5V<VIN<VOUT<12V,
TJ=25°C (Note 1,2) 0.5 %
2
Thermal Resistance from Junction to Ambient(Rthja)Note
TEST CONDITION
Line Regulation APE1117X-XX - 0.2
ADJ/
GND
VIN
VOUT
132
(Top View)
Tab is VOUT
SOT-223
VOUT VIN
132
(Top View)
Tab is VOUT
SOT-89 (G)
ADJ/
GND
ADJ/
GND
VOUT
VIN
(Top View)
Tab is VOUT
TO-252
123
APE1117X–XX -HF
Package Type Output Voltage
K : SOT-223
G : SOT-89
H : TO-252
Blank : ADJ
15 : 1.5V
18 : 1.8V
19 : 1.9V
25 : 2.5V
33 : 3.3V
50 : 5.0V
H alogen Free
Advanced Power
Electronics Corp. APE1117
ELECTRICAL SPECIFICATIONS(Cont.)
Parameter MIN TYP MAX UNITS
APE1117X-ADJ VIN=3.3V,10mA≦IOUT≦1A, TJ=25°C - 0.4 1 %
APE1117X-15 VIN=3V, 10mA≦IOUT≦1A, TJ=25°C
(Note 1,2) -1215mV
APE1117X-18 VIN=3.3V, 0mA≦IOUT ≦1A, TJ=25°
C (Note 1,2) -1518mV
APE1117X-25 VIN=4V, 10mA≦IOUT≦1A, TJ=25°C
(Note 1,2) -2025mV
APE1117X-33 VIN=5V,10mA≦IOUT ≦1A, TJ=25°C
(Note 1,2) -2633mV
APE1117X-50 VIN=6.5V,10mA≦IOUT≦1A, TJ=25°
C (Note 1,2) -4050mV
Reference Voltage APE1117X-ADJ IOUT = 10mA, TJ=25°C, (VIN-VOUT)=1.5V 1.225 1.25 1.275 V
APE1117X-15 IOUT = 10mA, TJ = 25°C, 3V≦VIN≦
12V 1.47 1.5 1.53 V
APE1117X-18 IOUT = 10mA, TJ = 25°C, 3.3V≦VIN
≦12V 1.764 1.8 1.836 V
APE1117X-25 IOUT = 10mA, TJ = 25°C, 4V≦VIN≦
12V 2.45 2.5 2.55 V
APE1117X-33 IOUT = 10mA, TJ = 25°C, 4.8V≦VIN
≦12V 3.235 3.3 3.365 V
APE1117X-50 IOUT = 10mA, TJ = 25°C, 6.5V≦VIN
≦12V 4.9 5 5.1 V
Ripple Rejection F=120Hz,COUT=10uF, APE1117X-
XX, (VIN-VOUT) = 3V, IOUT = 1A -6070dB
Temperature Stability IOUT=10mA - 0.5 - %
3
Load Regulation
TEST CONDITION
Output Voltage
Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a
constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package.
Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference
between input and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output
range.
Note3: Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the device is
gua
r
a
n
teed
to
r
egu
l
ate
if
t
h
e
output
cu
rr
e
n
t
i
s
g
r
eate
r
t
h
a
n 1
0
mA
.
Advanced Power
Electronics Corp. APE1117
PIN DESCRIPTIONS
PIN SYMBOL PIN DESCRIPTION
BLOCK DIAGRAM
4
ADJ/GND
VOUT
VIN
3
Thermal
Shutdown 1
2Vout
Adj
1.25V
+
+
CURRENT
LIMIT
Vin
-
+-
+
1
GND
(FIXED)
The output of the regulator. A capacitor ( 0.15Ω< ESR < 1Ω) must be connected
from this pin to ground to insure stability.
A
resistor divider from this pin to the VOUT pin and ground sets the output voltage.
(Ground only for Fixed-Mode)
The input pin of regulator. Typically a large storage capacitor (0.15Ω< ESR < 1
Ω) is connected from this pin to ground to insure that the input voltage does not
sag below the minimum dropout voltage during the load transient response. This
pin must always be 1.3V higher than Vout in order for the device to regulate
properly.
Advanced Power
Electronics Corp. APE1117
TYPICAL PERFORMANCE CHARACTERISTICS
5
D ropout Vol tage vs Output C urrent
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
00.2 0.4 0.6 0.8 1
Output Current (A)
Dropout Voltage (V)
Tj=25℃
Tj= 125℃
Temperature (℃)
Load Regulation vs Temperature
Output Voltage Deviation (%)
-25 0 25 50 75 100 125
-1
-0. 80
-0. 40
-0. 20
0
0.20
I load=800mA
Temperature (℃)
Percent C hange in Output
V oltage vs Temperature
Output Voltage Change (%)
-50 -25 0 25 50 75 100 125 150
-2
-1.5
-1
-0.5
0
0. 5
1
1.5
2
Input Voltage (V)
Line R egulation
Out put Volt age Deviation ( %)
0
0.2
0.4
0.6
0.8
1
246 81012
TIME (us)
Load Transient R esponse
Load Current (A) Output Voltage Deviation (mV)
010
20 30 40 50 60 70 80 90 100
-1
0
1
2
-20
-10
0
10
20
30 C in = 1uF
C out = 10 uF Tantalum
Preload = 100mA
TIME (us)
Li ne Transi ent R esponse
Out put VoltageDeviation (mV) I nput Voltage (V)
-40
-20
0
20
40
5. 5
6. 5
7. 5 Cin=1uF
Cout=10 uF Tantalum
0 20 40 60 80 100 120 140 160 180 200
Advanced Power
Electronics Corp. APE1117
MARKING INFORMATION
SOT-223
SOT-89
TO-252
6
XXXXXX
Part Number :
YWWSSS
Date Code (YWWSSS)
Y:Year
WW：Week
SSS：Sequence
XX
Identification code :
Part Number :
Logo
XXXXXX
YWWSSS
Date Code (YWWSSS)
Y：Last Digit Of The Year
WW：Week
SSS：Sequence
YWWS Date Code (YWWS)
Y:Year
WW：Week
S
：
Part Num ber Marking
APE1117K 1117
APE1117K-15 117-15
APE1117K-18 117-18
APE1117K-19 117-19
APE1117K-25 117-25
APE1117K-33 117-33
APE1117K-50 117-50
Part Number Identifica tion code
APE1117G EA
APE1117G-15 EB
APE1117G-18 EC
APE1117G-19 EG
APE1117G-25 ED
APE1117G-33 EF
APE1117G-50 EF
Part Number Marki ng
APE1117H 1117
APE1117H-15 117-15
APE1117H-18 117-18
APE1117H-19 117-19
APE1117H-25 117-25
APE1117H-33 117-33
APE1117H-50 117-50