OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com 36V, Single-Supply, SOT553, General-Purpose OPERATIONAL AMPLIFIERS Check for Samples: OPA171, OPA2171, OPA4171 FEATURES DESCRIPTION * * * * * * * * * * * * The OPA171, OPA2171 and OPA4171 (OPAx171) are a family of 36V, single-supply, low-noise operational amplifiers with the ability to operate on supplies ranging from +2.7V (1.35V) to +36V (18V). These devices are available in micro-packages and offer low offset, drift, and bandwidth with low quiescent current. The single, dual, and quad versions all have identical specifications for maximum design flexibility. 1 2 * Supply Range: +2.7V to +36V, 1.35V to 18V Low Noise: 14nV/Hz Low Offset Drift: 0.3V/C (typ) RFI Filtered Inputs Input Range Includes the Negative Supply Input Range Operates to Positive Supply Rail-to-Rail Output Gain Bandwidth: 3MHz Low Quiescent Current: 475A per Amplifier High Common-Mode Rejection: 120dB (typ) Low Input Bias Current: 8pA Industry-Standard Packages: - 8-Pin SOIC - 8-Pin MSOP - 14-Pin TSSOP microPackages: - Single in SOT553 - Dual in VSSOP-8 APPLICATIONS * * * * * * * * * Unlike most op amps, which are specified at only one supply voltage, the OPAx171 family is specified from +2.7V to +36V. Input signals beyond the supply rails do not cause phase reversal. The OPAx171 family is stable with capacitive loads up to 300pF. The input can operate 100mV below the negative rail and within 2V of the top rail during normal operation. Note that these devices can operate with full rail-to-rail input 100mV beyond the top rail, but with reduced performance within 2V of the top rail. The OPAx171 series of op amps are specified from -40C to +125C. Package Footprint Comparison (to Scale) Tracking Amplifier in Power Modules Merchant Power Supplies Transducer Amplifiers Bridge Amplifiers Temperature Measurements Strain Gauge Amplifiers Precision Integrators Battery-Powered Instruments Test Equipment Product Family DEVICE PACKAGE OPA171 SOT553, SOT23-5, SO-8 OPA2171 (dual) VSSOP-8, SO-8, MSOP-8 OPA4171 (quad) TSSOP-14, SO-14 Package Height Comparison (to Scale) D (SO-8) DBV (SOT23-5) DRL (SOT553) Smallest Packaging for 36V Op Amps 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR PACKAGE MARKING SOT553 DRL DAP OPA171 OPA2171 SOT23-5 DBV OSUI SO-8 D O171A MSOP-8 DGK OPMI VSSOP-8 DCU OPOC SO-8 D 2171A SO-14 D OPA4171 TSSOP-14 PW OPA4171 OPA4171 (1) (1) ORDERING NUMBER TRANSPORT MEDIA, QUANTITY OPA171AIDRLT Tape and Reel, 250 OPA171AIDRLR Tape and Reel, 4000 OPA171AIDBVT Tape and Reel, 250 OPA171AIDBVR Tape and Reel, 3000 OPA171AID Rail, 75 OPA171AIDR Tape and Reel, 2500 OPA2171AIDGK Rail, 80 OPA2171AIDGKR Tape and Reel, 2500 OPA2171AIDCUT Tape and Reel, 250 OPA2171AIDCUR Tape and Reel, 3000 OPA2171AID Rail, 75 OPA2171AIDR Tape and Reel, 2500 OPA4171AID Rail, 50 OPA4171AIDR Tape and Reel, 2500 OPA4171AIPW Rail, 90 OPA4171AIPWR Tape and Reel, 2000 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the device product folder at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Over operating free-air temperature range, unless otherwise noted. Supply voltage Signal input terminals OPAx171 UNIT 20 V Voltage (V-) - 0.5 to (V+) + 0.5 V Current 10 mA Output short circuit (2) Continuous Operating temperature -55 to +150 C Storage temperature -65 to +150 C Junction temperature +150 C 4 kV 750 V ESD ratings: (1) (2) 2 Human body model (HBM) Charged device model (CDM) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. Short-circuit to ground, one amplifier per package. Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com ELECTRICAL CHARACTERISTICS Boldface limits apply over the specified temperature range, TA = -40C to +125C. At TA = +25C, VS = +2.7V to +36V, VCM = VOUT = VS/2, and RLOAD = 10k connected to VS/2, unless otherwise noted. OPA171, OPA2171, OPA4171 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0.25 1.8 mV 0.3 2 mV OFFSET VOLTAGE Input offset voltage VOS Over temperature Drift vs power supply 0.3 2 V/C VS = +4V to +36V 1 3 V/V dc 5 dVOS/dT PSRR Channel separation, dc V/V INPUT BIAS CURRENT Input bias current 8 IB Over temperature Input offset current 15 pA 3.5 nA 3.5 nA 4 IOS pA Over temperature NOISE Input voltage noise Input voltage noise density en f = 0.1Hz to 10Hz 3 VPP f = 100Hz 25 nV/Hz f = 1kHz 14 nV/Hz INPUT VOLTAGE Common-mode voltage range (1) Common-mode rejection ratio (V-) - 0.1V VCM CMRR (V+) - 2V V VS = 2V, (V-) - 0.1V < VCM < (V+) - 2V 90 104 dB VS = 18V, (V-) - 0.1V < VCM < (V+) - 2V 104 120 dB INPUT IMPEDANCE Differential Common-mode 100 || 3 M || pF 6 || 3 1012 || pF 130 dB 3.0 MHz 1.5 V/s OPEN-LOOP GAIN Open-loop voltage gain AOL VS = +4V to +36V, (V-) + 0.35V < VO < (V+) - 0.35V 110 FREQUENCY RESPONSE Gain bandwidth product Slew rate Settling time GBP SR tS G = +1 To 0.1%, VS = 18V, G = +1, 10V step 6 s To 0.01% (12 bit), VS = 18V, G = +1, 10V step 10 s 2 s 0.0002 % VIN x Gain > VS Overload recovery time Total harmonic distortion + noise THD+N G = +1, f = 1kHz, VO = 3VRMS OUTPUT Voltage output swing from rail VO Short-circuit current Capacitive load drive Open-loop output resistance VS = 5V, RL = 10k RL = 10k, AOL 110dB Over temperature 30 ISC +25/-35 CLOAD RO mV (V+) - 0.35 (V-) + 0.35 See Typical Characteristics f = 1MHz, IO = 0A V mA pF 150 POWER SUPPLY Specified voltage range VS Quiescent current per amplifier IQ Over temperature +2.7 IO = 0A 475 IO = 0A +36 V 595 A 650 A TEMPERATURE Specified range -40 +125 C Operating range -55 +150 C (1) The input range can be extended beyond (V+) - 2V up to V+. See the Typical Characteristics and Application Information sections for additional information. Copyright (c) 2010-2011, Texas Instruments Incorporated 3 OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com THERMAL INFORMATION: OPA171 OPA171 THERMAL METRIC (1) D (SO) DBV (SOT23) DRL (SOT553) 8 PINS 5 PINS 5 PINS 208.1 JA Junction-to-ambient thermal resistance 149.5 245.8 JC(top) Junction-to-case(top) thermal resistance 97.9 133.9 0.1 JB Junction-to-board thermal resistance 87.7 83.6 42.4 JT Junction-to-top characterization parameter 35.5 18.2 0.5 JB Junction-to-board characterization parameter 89.5 83.1 42.2 JC(bottom) Junction-to-case(bottom) thermal resistance N/A N/A N/A (1) UNITS C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. THERMAL INFORMATION: OPA2171 OPA2171 THERMAL METRIC (1) D (SO) DCU (VSSOP) DGK (MSOP) 8 PINS 8 PINS 8 PINS 195.3 JA Junction-to-ambient thermal resistance 134.3 175.2 JC(top) Junction-to-case(top) thermal resistance 72.1 74.9 59.4 JB Junction-to-board thermal resistance 60.6 22.2 115.1 JT Junction-to-top characterization parameter 18.2 1.6 4.7 JB Junction-to-board characterization parameter 53.8 22.8 114.4 JC(bottom) Junction-to-case(bottom) thermal resistance N/A N/A N/A (1) UNITS C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. THERMAL INFORMATION: OPA4171 OPA4171 THERMAL METRIC (1) D (SO) PW (TSSOP) 14 PINS 14 PINS JA Junction-to-ambient thermal resistance 93.2 106.9 JC(top) Junction-to-case(top) thermal resistance 51.8 24.4 JB Junction-to-board thermal resistance 49.4 59.3 JT Junction-to-top characterization parameter 13.5 0.6 JB Junction-to-board characterization parameter 42.2 54.3 JC(bottom) Junction-to-case(bottom) thermal resistance N/A N/A (1) 4 UNITS C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com PIN CONFIGURATIONS DRL PACKAGE: OPA171 SOT-553 (TOP VIEW) IN+ 1 V- 2 IN- 3 D, DCU, AND DGK PACKAGES: OPA2171 SO-8, VSSOP-8, AND MSOP-8 (TOP VIEW) 5 V+ 4 OUT DBV PACKAGE: OPA171 SOT23-5 (TOP VIEW) OUT 1 V- 2 +IN 3 5 V+ 4 -IN 1 8 V+ -IN A 2 7 OUT B +IN A 3 6 -IN B V- 4 5 +IN B D AND PW PACKAGES: OPA4171 SO-14 AND TSSOP-14 (TOP VIEW) D PACKAGE: OPA171 SO-8 (TOP VIEW) (1) OUT A NC(1) 1 8 NC(1) -IN 2 7 V+ +IN 3 6 OUT V- 4 5 NC(1) OUT A 1 14 OUT D -IN A 2 13 -IN D +IN A 3 12 +IN D V+ 4 11 V- +IN B 5 10 +IN C -IN B 6 9 -IN C OUT B 7 8 OUT C No internal connection. Copyright (c) 2010-2011, Texas Instruments Incorporated 5 OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS TABLE OF GRAPHS Table 1. Characteristic Performance Measurements 6 DESCRIPTION FIGURE Offset Voltage Production Distribution Figure 1 Offset Voltage Drift Distribution Figure 2 Offset Voltage vs Temperature Figure 3 Offset Voltage vs Common-Mode Voltage Figure 4 Offset Voltage vs Common-Mode Voltage (Upper Stage) Figure 5 Offset Voltage vs Power Supply Figure 6 IB and IOS vs Common-Mode Voltage Figure 7 Input Bias Current vs Temperature Figure 8 Output Voltage Swing vs Output Current (Maximum Supply) Figure 9 CMRR and PSRR vs Frequency (Referred-to Input) Figure 10 CMRR vs Temperature Figure 11 PSRR vs Temperature Figure 12 0.1Hz to 10Hz Noise Figure 13 Input Voltage Noise Spectral Density vs Frequency Figure 14 THD+N Ratio vs Frequency Figure 15 THD+N vs Output Amplitude Figure 16 Quiescent Current vs Temperature Figure 17 Quiescent Current vs Supply Voltage Figure 18 Open-Loop Gain and Phase vs Frequency Figure 19 Closed-Loop Gain vs Frequency Figure 20 Open-Loop Gain vs Temperature Figure 21 Open-Loop Output Impedance vs Frequency Figure 22 Small-Signal Overshoot vs Capacitive Load (100mV Output Step) Figure 23, Figure 24 No Phase Reversal Figure 25 Positive Overload Recovery Figure 26 Negative Overload Recovery Figure 27 Small-Signal Step Response (100mV) Figure 28, Figure 29 Large-Signal Step Response Figure 30, Figure 31 Large-Signal Settling Time (10V Positive Step) Figure 32 Large-Signal Settling Time (10V Negative Step) Figure 33 Short-Circuit Current vs Temperature Figure 34 Maximum Output Voltage vs Frequency Figure 35 Channel Separation vs Frequency Figure 36 Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS VS = 18V, VCM = VS/2, RLOAD = 10k connected to VS/2, and CL = 100pF, unless otherwise noted. OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT DISTRIBUTION 25 Distribution Taken From 3500 Amplifiers 14 Percentage of Amplifiers (%) Percentage of Amplifiers (%) 16 12 10 8 6 4 2 0 Distribution Taken From 110 Amplifiers 20 15 10 5 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 -1200 -1100 -1000 -900 -800 -700 -600 -500 -400 -300 -200 -100 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 0 Offset Voltage Drift (mV/C) Offset Voltage (mV) Figure 1. Figure 2. OFFSET VOLTAGE vs TEMPERATURE OFFSET VOLTAGE vs COMMON-MODE VOLTAGE 1000 600 5 Typical Units Shown 10 Typical Units Shown 800 400 400 VOS (mV) Offset Voltage (mV) 600 200 0 -200 200 0 -200 -400 -400 -600 -600 -800 -800 VCM = -18.1V -1000 -75 -50 -25 0 25 50 75 100 125 150 -20 -15 -10 0 -5 Figure 3. 10 15 20 Figure 4. OFFSET VOLTAGE vs COMMON-MODE VOLTAGE (Upper Stage) 10000 5 VCM (V) Temperature (C) OFFSET VOLTAGE vs POWER SUPPLY 350 10 Typical Units Shown 8000 VSUPPLY = 1.35V to 18V 10 Typical Units Shown 250 6000 150 2000 VOS (mV) VOS (mV) 4000 0 -2000 -4000 Normal Operation -250 -8000 -10000 15.5 -50 -150 VCM = +18.1V -6000 50 -350 16 16.5 17 17.5 VCM (V) Figure 5. Copyright (c) 2010-2011, Texas Instruments Incorporated 18 18.5 0 2 4 6 8 10 12 14 16 18 20 VSUPPLY (V) Figure 6. 7 OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = 18V, VCM = VS/2, RLOAD = 10k connected to VS/2, and CL = 100pF, unless otherwise noted. INPUT BIAS CURRENT vs TEMPERATURE 10000 IB+ -IB +IB -IOS VCM = -18.1V IB- 1000 Input Bias Current (pA) IB and IOS (pA) IB AND IOS vs COMMON-MODE VOLTAGE 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 IB IOS 100 10 IOS 1 VCM = 16V 0 -20 -18 -12 0 -6 6 12 18 20 -75 -50 0 -25 VCM (V) 100 125 OUTPUT VOLTAGE SWING vs OUTPUT CURRENT (Maximum Supply) CMRR AND PSRR vs FREQUENCY (Referred-to Input) 150 140 Common-Mode Rejection Ratio (dB), Power-Supply Rejection Ratio (dB) Output Voltage (V) 75 Figure 8. 17 16 15 14.5 -14.5 -15 -40C +25C +85C +125C -16 -17 120 100 80 60 40 +PSRR -PSRR CMRR 20 0 -18 0 2 4 6 8 10 12 14 1 16 10 100 1k 10k 100k 1M 10M Frequency (Hz) Output Current (mA) Figure 9. Figure 10. CMRR vs TEMPERATURE PSRR vs TEMPERATURE 30 3 Power-Supply Rejection Ratio (mV/V) Common-Mode Rejection Ratio (mV/V) 50 Figure 7. 18 20 10 0 -10 VS = 2.7V -20 VS = 4V VS = 36V -30 2 1 0 -1 -2 VS = 2.7V to 36V VS = 4V to 36V -3 -75 8 25 Temperature (C) -50 -25 0 25 50 75 100 125 150 -75 -50 -25 0 25 50 Temperature (C) Temperature (C) Figure 11. Figure 12. 75 100 125 150 Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = 18V, VCM = VS/2, RLOAD = 10k connected to VS/2, and CL = 100pF, unless otherwise noted. INPUT VOLTAGE NOISE SPECTRAL DENSITY vs FREQUENCY 0.1Hz TO 10Hz NOISE 1mV/div Voltage Noise Density (nV/OHz) 1000 100 10 1 Time (1s/div) 1 10 100 1k 10k 100k 1M Frequency (Hz) Figure 13. Figure 14. THD+N RATIO vs FREQUENCY 0.001 -100 0.0001 -120 G = +1, RL = 10kW G = -1, RL = 2kW 0.00001 10 100 1k 10k -140 20k Total Harmonic Distortion + Noise (%) VOUT = 3VRMS BW = 80kHz 0.1 -80 BW = 80kHz 0.01 -100 0.001 -120 0.0001 G = +1, RL = 10kW G = -1, RL = 2kW 0.00001 0.01 -140 0.1 1 10 20 Output Amplitude (VRMS) Frequency (Hz) Figure 15. Figure 16. QUIESCENT CURRENT vs TEMPERATURE QUIESCENT CURRENT vs SUPPLY VOLTAGE 0.65 0.6 0.6 0.55 0.5 IQ (mA) 0.55 IQ (mA) Total Harmonic Distortion + Noise (dB) Total Harmonic Distortion + Noise (%) THD+N vs OUTPUT AMPLITUDE -80 Total Harmonic Distortion + Noise (dB) 0.01 0.5 0.45 0.45 0.4 0.35 0.4 0.3 0.35 0.25 Specified Supply-Voltage Range -75 -50 -25 0 25 50 75 Temperature (C) Figure 17. Copyright (c) 2010-2011, Texas Instruments Incorporated 100 125 150 0 4 8 12 16 20 24 28 32 36 Supply Voltage (V) Figure 18. 9 OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = 18V, VCM = VS/2, RLOAD = 10k connected to VS/2, and CL = 100pF, unless otherwise noted. OPEN-LOOP GAIN AND PHASE vs FREQUENCY CLOSED-LOOP GAIN vs FREQUENCY 180 180 25 Gain 20 135 135 15 Phase 45 45 Gain (dB) 90 Phase () Gain (dB) 10 90 5 0 -5 -10 0 0 G = 10 G=1 G = -1 -15 -45 1 10 100 1k 10k 100k -20 -45 10M 1M 10k 100k 1M Figure 19. OPEN-LOOP OUTPUT IMPEDANCE vs FREQUENCY 1M 5 Typical Units Shown VS = 2.7V VS = 4V VS = 36V 2.5 100k 10k ZO (W) AOL (mV/V) 2 1.5 1 1k 100 10 0.5 1 0 1m -75 -50 -25 0 25 50 75 100 150 125 1 10 100 Temperature (C) 10k 100k 1M 10M Figure 22. SMALL-SIGNAL OVERSHOOT vs CAPACITIVE LOAD (100mV Output Step) SMALL-SIGNAL OVERSHOOT vs CAPACITIVE LOAD (100mV Output Step) 50 RL = 10kW ROUT = 0W 40 40 ROUT = 25W 35 35 ROUT = 50W 30 25 20 15 ROUT = 0W 10 ROUT = 25W 5 ROUT = 50W G = +1 +18V Overshoot (%) 45 45 Overshoot (%) 1k Frequency (Hz) Figure 21. 50 30 25 20 RI = 10kW 15 ROUT RF = 10kW G = -1 +18V OPA171 RL CL 10 ROUT OPA171 -18V CL 5 -18V 0 0 0 10 100M Figure 20. OPEN-LOOP GAIN vs TEMPERATURE 3 10M Frequency (Hz) Frequency (Hz) 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Capacitive Load (pF) Figure 23. Figure 24. Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = 18V, VCM = VS/2, RLOAD = 10k connected to VS/2, and CL = 100pF, unless otherwise noted. NO PHASE REVERSAL POSITIVE OVERLOAD RECOVERY +18V Output VOUT OPA171 VIN 5V/div 5V/div -18V 37VPP Sine Wave (18.5V) 20kW +18V 2kW OPA171 Output VOUT VIN -18V G = -10 Time (5ms/div) Time (100ms/div) Figure 25. Figure 26. NEGATIVE OVERLOAD RECOVERY SMALL-SIGNAL STEP RESPONSE (100mV) RL = 10kW CL = 100pF +18V RL CL 20mV/div -18V VIN 5V/div G = +1 OPA171 20kW +18V 2kW OPA171 VOUT VIN VOUT -18V G = -10 Time (5ms/div) Time (1ms/div) Figure 27. Figure 28. SMALL-SIGNAL STEP RESPONSE (100mV) LARGE-SIGNAL STEP RESPONSE G = +1 RL = 10kW CL = 100pF RI = 2kW RF 2V/div 20mV/div CL = 100pF = 2kW +18V OPA171 CL -18V G = -1 Time (20ms/div) Time (5ms/div) Figure 29. Figure 30. Copyright (c) 2010-2011, Texas Instruments Incorporated 11 OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) VS = 18V, VCM = VS/2, RLOAD = 10k connected to VS/2, and CL = 100pF, unless otherwise noted. LARGE-SIGNAL SETTLING TIME (10V Positive Step) LARGE-SIGNAL STEP RESPONSE 10 G = -1 RL = 10kW CL = 100pF G = -1 2V/div D From Final Value (mV) 8 6 4 12-Bit Settling 2 0 -2 (1/2LSB = 0.024%) -4 -6 -8 -10 Time (4ms/div) 0 4 8 12 16 20 24 28 32 36 Time (ms) Figure 31. Figure 32. LARGE-SIGNAL SETTLING TIME (10V Negative Step) 10 G = -1 8 45 ISC, Sink 40 6 4 35 12-Bit Settling 2 ISC (mA) D From Final Value (mV) SHORT-CIRCUIT CURRENT vs TEMPERATURE 50 0 -2 (1/2LSB = 0.024%) 30 25 20 -4 15 -6 10 -8 5 ISC, Source 0 -10 0 4 8 12 16 20 24 28 32 36 -75 -50 -25 Time (ms) 0 25 50 75 100 125 150 Temperature (C) Figure 33. Figure 34. MAXIMUM OUTPUT VOLTAGE vs FREQUENCY CHANNEL SEPARATION vs FREQUENCY 15 -60 VS = 15V 10 Channel Separation (dB) Output Voltage (VPP) 12.5 Maximum output voltage without slew-rate induced distortion. 7.5 VS = 5V 5 2.5 -80 -90 -100 -110 VS = 1.35V 0 -120 10k 12 -70 100k 1M 10M 10 100 1k Frequency (Hz) Frequency (Hz) Figure 35. Figure 36. 10k 100k Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com APPLICATION INFORMATION The OPAx171 family of operational amplifiers provide high overall performance, making them ideal for many general-purpose applications. The excellent offset drift of only 2V/C provides excellent stability over the entire temperature range. In addition, the device offers very good overall performance with high CMRR, PSRR, and AOL. As with all amplifiers, applications with noisy or high-impedance power supplies require decoupling capacitors close to the device pins. In most cases, 0.1F capacitors are adequate. OPERATING CHARACTERISTICS The OPAx171 family of amplifiers is specified for operation from 2.7V to 36V (1.35V to 18V). Many of the specifications apply from -40C to +125C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. This device can operate with full rail-to-rail input 100mV beyond the top rail, but with reduced performance within 2V of the top rail. The typical performance in this range is summarized in Table 2. PHASE-REVERSAL PROTECTION The OPAx171 family has an internal phase-reversal protection. Many op amps exhibit a phase reversal when the input is driven beyond its linear common-mode range. This condition is most often encountered in noninverting circuits when the input is driven beyond the specified common-mode voltage range, causing the output to reverse into the opposite rail. The input of the OPAx171 prevents phase reversal with excessive common-mode voltage. Instead, the output limits into the appropriate rail. This performance is shown in Figure 37. +18V Output GENERAL LAYOUT GUIDELINES -18V 37VPP Sine Wave (18.5V) 5V/div For best operational performance of the device, good printed circuit board (PCB) layout practices are recommended. Low-loss, 0.1F bypass capacitors should be connected between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable to single-supply applications. OPA171 Output COMMON-MODE VOLTAGE RANGE Time (100ms/div) The input common-mode voltage range of the OPAx171 series extends 100mV below the negative rail and within 2V of the top rail for normal operation. Figure 37. No Phase Reversal Table 2. Typical Performance Range PARAMETER Input Common-Mode Voltage Offset voltage MIN TYP (V+) - 2 MAX (V+) + 0.1 UNIT V 7 mV 12 V/C Common-mode rejection 65 dB Open-loop gain 60 dB GBW 0.7 MHz Slew rate 0.7 V/s Noise at f = 1kHz 30 nV/Hz vs Temperature Copyright (c) 2010-2011, Texas Instruments Incorporated 13 OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com CAPACITIVE LOAD AND STABILITY The dynamic characteristics of the OPAx171 have been optimized for commonly encountered operating conditions. The combination of low closed-loop gain and high capacitive loads decreases the phase margin of the amplifier and can lead to gain peaking or oscillations. As a result, heavier capacitive loads must be isolated from the output. The simplest way to achieve this isolation is to add a small resistor (for example, ROUT equal to 50) in series with the output. Figure 38 and Figure 39 illustrate graphs of small-signal overshoot versus capacitive load for several values of ROUT. Also, refer to Applications Bulletin AB-028 (SBOA015), available for download from the TI website for details of analysis techniques and application circuits. 50 or even the output pin. Each of these different pin functions have electrical stress limits determined by the voltage breakdown characteristics of the particular semiconductor fabrication process and specific circuits connected to the pin. Additionally, internal electrostatic discharge (ESD) protection is built into these circuits to protect them from accidental ESD events both before and during product assembly. These ESD protection diodes also provide in-circuit, input overdrive protection, as long as the current is limited to 10mA as stated in the Absolute Maximum Ratings. Figure 40 shows how a series input resistor may be added to the driven input to limit the input current. The added resistor contributes thermal noise at the amplifier input and its value should be kept to a minimum in noise-sensitive applications. RL = 10kW 45 V+ Overshoot (%) 40 IOVERLOAD 10mA max 35 30 OPA171 5kW 20 15 ROUT = 0W 10 ROUT = 25W 5 ROUT = 50W G = +1 +18V ROUT Figure 40. Input Current Protection OPA171 RL CL -18V 0 0 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Figure 38. Small-Signal Overshoot versus Capacitive Load (100mV Output Step) Overshoot (%) 50 45 ROUT = 0W 40 ROUT = 25W 35 ROUT = 50W 30 25 20 RI = 10kW 15 RF = 10kW G = -1 +18V 10 ROUT OPA171 CL 5 -18V 0 0 100 200 300 400 500 600 700 800 900 1000 Capacitive Load (pF) Figure 39. Small-Signal Overshoot versus Capacitive Load (100mV Output Step) ELECTRICAL OVERSTRESS Designers often ask questions about the capability of an operational amplifier to withstand electrical overstress. These questions tend to focus on the device inputs, but may involve the supply voltage pins 14 VOUT VIN 25 An ESD event produces a short duration, high-voltage pulse that is transformed into a short duration, high-current pulse as it discharges through a semiconductor device. The ESD protection circuits are designed to provide a current path around the operational amplifier core to prevent it from being damaged. The energy absorbed by the protection circuitry is then dissipated as heat. When the operational amplifier connects into a circuit, the ESD protection components are intended to remain inactive and not become involved in the application circuit operation. However, circumstances may arise where an applied voltage exceeds the operating voltage range of a given pin. Should this condition occur, there is a risk that some of the internal ESD protection circuits may be biased on, and conduct current. Any such current flow occurs through ESD cells and rarely involves the absorption device. If there is an uncertainty about the ability of the supply to absorb this current, external zener diodes may be added to the supply pins. The zener voltage must be selected such that the diode does not turn on during normal operation. However, its zener voltage should be low enough so that the zener diode conducts if the supply pin begins to rise above the safe operating supply voltage level. Copyright (c) 2010-2011, Texas Instruments Incorporated OPA171 OPA2171 OPA4171 SBOS516C - SEPTEMBER 2010 - REVISED JUNE 2011 www.ti.com REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (November 2010) to Revision C Page * Added MSOP-8 package to device graphic .......................................................................................................................... 1 * Added MSOP-8 package to Features bullets ....................................................................................................................... 1 * Added MSOP-8 package to Product Family table ................................................................................................................ 1 * Added MSOP-8 package to Package/Ordering Information table ........................................................................................ 2 * Deleted "A" suffix from OPA4171 package markings in Package/Ordering Information table. ............................................ 2 * Added new row for Voltage Output Swing from Rail parameter to Output subsection of Electrical Characteristics ............ 3 * Changed Voltage Output Swing from Rail parameter to over temperature in Output subsection of Electrical Characteristics ...................................................................................................................................................................... 3 * Updated format of thermal information tables ...................................................................................................................... 4 * Added MSOP-8 package to OPA2171 Thermal Information table ....................................................................................... 4 * Updated pinout configurations for OPA2171 and OPA4171 ................................................................................................ 5 * Changed Figure 9 ................................................................................................................................................................. 8 Changes from Revision A (November, 2010) to Revision B Page * Changed input offset voltage specification ........................................................................................................................... 3 * Changed input offset voltage, over temperature specification .............................................................................................. 3 * Changed quiescent current per amplifier, over temperature specification ........................................................................... 3 Copyright (c) 2010-2011, Texas Instruments Incorporated 15 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device (1) Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA171AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA171AIDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA171AIDBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA171AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA171AIDRLR ACTIVE SOT DRL 5 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA171AIDRLT ACTIVE SOT DRL 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA2171AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2171AIDCUR ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA2171AIDCUT ACTIVE US8 DCU 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA2171AIDGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2171AIDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2171AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4171AID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA4171AIDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA4171AIPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4171AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR The marketing status values are defined as follows: Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF OPA171 : * Automotive: OPA171-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) OPA171AIDBVR SOT-23 DBV 5 3000 180.0 OPA171AIDBVT SOT-23 DBV 5 250 OPA171AIDR SOIC D 8 2500 OPA171AIDRLR SOT DRL 5 OPA171AIDRLT SOT DRL OPA2171AIDCUR US8 OPA2171AIDCUT US8 OPA2171AIDGKR B0 (mm) K0 (mm) P1 (mm) 8.4 3.23 3.17 1.37 4.0 180.0 8.4 3.23 3.17 1.37 330.0 12.4 6.4 5.2 2.1 4000 180.0 8.4 1.98 1.78 5 250 180.0 8.4 1.98 DCU 8 3000 180.0 8.4 DCU 8 250 180.0 8.4 VSSOP DGK 8 2500 330.0 OPA2171AIDR SOIC D 8 2500 OPA4171AIDR SOIC D 14 2500 OPA4171AIPWR TSSOP PW 14 2000 W Pin1 (mm) Quadrant 8.0 Q3 4.0 8.0 Q3 8.0 12.0 Q1 0.69 4.0 8.0 Q3 1.78 0.69 4.0 8.0 Q3 2.25 3.35 1.05 4.0 8.0 Q3 2.25 3.35 1.05 4.0 8.0 Q3 12.4 5.3 3.4 1.4 8.0 12.0 Q1 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA171AIDBVR SOT-23 DBV 5 3000 202.0 201.0 28.0 OPA171AIDBVT SOT-23 DBV 5 250 202.0 201.0 28.0 OPA171AIDR SOIC D 8 2500 367.0 367.0 35.0 OPA171AIDRLR SOT DRL 5 4000 202.0 201.0 28.0 OPA171AIDRLT SOT DRL 5 250 202.0 201.0 28.0 OPA2171AIDCUR US8 DCU 8 3000 202.0 201.0 28.0 OPA2171AIDCUT US8 DCU 8 250 202.0 201.0 28.0 OPA2171AIDGKR VSSOP DGK 8 2500 366.0 364.0 50.0 OPA2171AIDR SOIC D 8 2500 367.0 367.0 35.0 OPA4171AIDR SOIC D 14 2500 367.0 367.0 38.0 OPA4171AIPWR TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated