R74125J500BRT - KEMET Electronics Corporation

NISSEI-ARCOTRONICS R74

Bulk Taped

Fig. 1 Fig. 2

p = 10 p ≥ 15

Ød ±

0.05 0.6 0.8

Fig. 1 Fig 2

P2 12.70 19.05

All dimensions are in mm.

MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

A.C. APPLICATIONS

Typical applications: electronic lighting (i.e. car headlamp

and ballast), pulse applications with high A.C. voltage and

medium current.

SERIES CODE: R74

PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8

[ ]

1. Series code

2. Capacitance value in pico farads. First 2

digits are significant and 3rd digit indicates

number of zeros.

3. Capacitance tolerance

J = 5% K = 10%

4. A.C. voltage

5. Packaging code

B = bulk A = ammo R = reel

6. Lead spacing (mm)

I = 15 N = 22.5 R = 27.5

7. Lead length (mm) – (Applies to bulk

packaging only. Omit for standard lead

length 4-6mm.)

L = 24-27 T = 3.5-4.0 V = 2.7-3.3

8. Internal code

GENERAL TECHNICAL DATA

Dielectric: polypropylene film

Plates: aluminum layer deposited by evaporation

under vacuum

Winding: non-inductive type

Leads: tinned wire

Protection: plastic case, epoxy resin filled. Box material

is solvent resistant and flame retardant

according to UL94 V0

Marking: manufacturer’s logo, series (R74), dielectric

code (MKP), capacitance, tolerance, A.C.

voltage, manufacturing date code

Climatic category: 55/100/56 IEC 60068-1

Operating temperature range: -55 to +105°C

Related documents: IEC 60384-16; IEC 60384-17

CECC 31200

Typical application: LAMP CAPACITOR IN ELECTRONIC BALLAST

Rectifier

bridge

Step-up

circuit

Switching

circuit

EMI filter

Rectifier

bridge

Step-up

circuit

Switching

circuit

R74

R 7 4

EMI filter

Typical European scheme

Typical U.S. scheme

NISSEI-ARCOTRONICS R74

MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

A.C. APPLICATIONS

SERIES CODE: R74

All dimensions are in mm.

Rated

Cap. 250Vac* (1 section) Max

dv/dt Max K0 Part Number

B H L P (V/µs) (V2/µs)

0.010µF 4.0 9.0 13.0 10.0 300 38 E4 R74103-250-F-

0.012µF 4.0 9.0 13.0 10.0 300 38 E4 R74123-250-F-

0.015µF 5.0 11.0 13.0 10.0 300 38 E4 R74153-250-F-

0.022µF 6.0 12.0 13.0 10.0 300 38 E4 R74223-250-F-

0.027µF 6.0 12.0 13.0 10.0 300 38 E4 R74273-250-F-

0.015µF 5.0 11.0 18.0 15.0 250 31 E4 R74153-250-I-

0.018µF 5.0 11.0 18.0 15.0 250 31 E4 R74183-250-I-

0.022µF 5.0 11.0 18.0 15.0 250 31 E4 R74223-250-I-

0.027µF 5.0 11.0 18.0 15.0 250 31 E4 R74273-250-I-

0.033µF 5.0 11.0 18.0 15.0 250 31 E4 R74333-250-I-

0.039µF 6.0 12.0 18.0 15.0 250 31 E4 R74393-250-I-

0.047µF 6.0 12.0 18.0 15.0 250 31 E4 R74473-250-I-

0.056µF 7.5 13.5 18.0 15.0 250 31 E4 R74563-250-I-

0.068µF 7.5 13.5 18.0 15.0 250 31 E4 R74683-250-I-

0.082µF 8.5 14.5 18.0 15.0 250 31 E4 R74823-250-I-

0.10µF 8.5 14.5 18.0 15.0 250 31 E4 R74104-250-I-

0.12µF 10.0 16.0 18.0 15.0 250 31 E4 R74124-250-I-

Tolerance: J (± 5%); K (±10%)

Packaging code: B (bulk); A (ammo); R (reel)

Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3)

Omit for standard (4-6)

* Not suitable for across-the-line applications. Please

refer to Interference Suppression Capacitors.

Rated

Cap. 400Vac (2 sections) Max

dv/dt Max K0Part Number

B H L P (V/µs) (V2/µs)

2200ρF 4.0 9.0 13.0 10.0 1200 240 E4 R74222-400-F-

2700ρF 4.0 9.0 13.0 10.0 1200 240 E4 R74272-400-F-

3300ρF 4.0 9.0 13.0 10.0 1200 240 E4 R74332-400-F-

3900ρF 5.0 11.0 13.0 10.0 1200 240 E4 R74392-400-F-

4700ρF 5.0 11.0 13.0 10.0 1200 240 E4 R74472-400-F-

5600ρF 5.0 11.0 13.0 10.0 1200 240 E4 R74562-400-F-

6800ρF 6.0 12.0 13.0 10.0 1200 240 E4 R74682-400-F-

8200ρF 6.0 12.0 13.0 10.0 1200 240 E4 R74822-400-F-

6800ρF 5.0 11.0 18.0 15.0 1000 200 E4 R74682-400-I-

8200ρF 5.0 11.0 18.0 15.0 1000 200 E4 R74822-400-I-

0.010µF 5.0 11.0 18.0 15.0 1000 200 E4 R74103-400-I-

0.012µF 6.0 12.0 18.0 15.0 1000 200 E4 R74123-400-I-

0.015µF 6.0 12.0 18.0 15.0 1000 200 E4 R74153-400-I-

0.018µF 7.5 13.5 18.0 15.0 1000 200 E4 R74183-400-I-

0.022µF 7.5 13.5 18.0 15.0 1000 200 E4 R74223-400-I-

0.027µF 8.5 14.5 18.0 15.0 1000 200 E4 R74273-400-I-

0.033µF 8.5 14.5 18.0 15.0 1000 200 E4 R74333-400-I-

0.039µF 10.0 16.0 18.0 15.0 1000 200 E4 R74393-400-I-

0.047µF 10.0 16.0 18.0 15.0 1000 200 E4 R74473-400-I-

0.039µF 6.0 15.0 26.5 22.5 500 100 E4 R74393-400-N-

0.047µF 7.0 16.0 26.5 22.5 500 100 E4 R74473-400-N-

0.056µF 7.0 16.0 26.5 22.5 500 100 E4 R74563-400-N-

0.068µF 8.5 17.0 26.5 22.5 500 100 E4 R74683-400-N-

0.082µF 10.0 18.5 26.5 22.5 500 100 E4 R74823-400-N-

0.10µF 10.0 18.5 26.5 22.5 500 100 E4 R74104-400-N-

Tolerance: J (± 5%); K (±10%)

Packaging code: B (bulk); A (ammo); R (reel)

Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3)

Omit for standard (4-6)

Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case

the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The

pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the

above table. The dv/dt test is carried out at 2 times the above values.

single side metallized

polypropylene film

single side metallized

polypropylene film

2 sections

(400Vac)

1 section

(250Vac)

NISSEI-ARCOTRONICS R74

MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

A.C. APPLICATIONS

SERIES CODE: R74

ll dimensions are in mm.

Rated

Cap. 500Vac (2 sections) Max

dv/dt Max K0 Part Number

B H L P (V/µs) (V2/µs)

1000ρF 4.0 9.0 13.0 10.0 2000 520 E4 R74102-500-F-

1200ρF 4.0 9.0 13.0 10.0 2000 520 E4 R74122-500-F-

1500ρF 4.0 9.0 13.0 10.0 2000 520 E4 R74152-500-F-

1800ρF 4.0 9.0 13.0 10.0 2000 520 E4 R74182-500-F-

2200ρF 5.0 11.0 13.0 10.0 2000 520 E4 R74222-500-F-

2700ρF 5.0 11.0 13.0 10.0 2000 520 E4 R74272-500-F-

3300ρF 6.0 12.0 13.0 10.0 2000 520 E4 R74332-500-F-

3900ρF 6.0 12.0 13.0 10.0 2000 520 E4 R74392-500-F-

4700ρF 6.0 12.0 13.0 10.0 2000 520 E4 R745472-500-F-

1500ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74152-500-I-

1800ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74182-500-I-

2200ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74222-500-I-

2700ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74272-500-I-

3300ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74332-500-I-

3900ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74392-500-I-

4700ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74472-500-I-

5600ρF 5.0 11.0 18.0 15.0 1300 340 E4 R74562-500-I-

6800ρF 6.0 12.0 18.0 15.0 1300 340 E4 R74682-500-I-

8200ρF 6.0 12.0 18.0 15.0 1300 340 E4 R74822-500-I-

0.010µF 6.0 12.0 18.0 15.0 1300 340 E4 R74103-500-I-

0.012µF 7.5 13.5 18.0 15.0 1300 340 E4 R74123-500-I-

0.015µF 7.5 13.5 18.0 15.0 1300 340 E4 R74153-500-I-

0.018µF 8.5 14.5 18.0 15.0 1300 340 E4 R74183-500-I-

0.022µF 10.0 16.0 18.0 15.0 1300 340 E4 R74223-500-I-

0.027µF 10.0 16.0 18.0 15.0 1300 340 E4 R74273-500-I-

0.018µF 6.0 15.0 26.5 22.5 700 180 E4 R74183-500-N--

0.022µF 6.0 15.0 26.5 22.5 700 180 E4 R74223-500-N-

0.027µF 7.0 16.0 26.5 22.5 700 180 E4 R74273-500-N-

0.033µF 7.0 16.0 26.5 22.5 700 180 E4 R74333-500-N-

0.039µF 8.5 17.0 26.5 22.5 700 180 E4 R74393-500-N-

0.047µF 10.0 18.5 26.5 22.5 700 180 E4 R74473-500-N-

0.056µF 10.0 18.5 26.5 22.5 700 180 E4 R74563-500-N-

0.068µF 11.0 20.0 26.5 22.5 700 180 E4 R74683-500-N-

Tolerance: J (± 5%); K (±10%)

Packaging code: B (bulk); A (ammo); R (reel)

Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3)

Omit for standard (4-6)

Rated

Cap. 500Vac (2 sections) Max

dv/dt Max K0Part Number

B H L P (V/µs) (V2/µs)

0.082µF 11.0 20.0 32.0 27.5 500 130 E4 R74823-500-R-

0.10µF 11.0 20.0 32.0 27.5 500 130 E4 R74104-500-R-

0.15µF 9.0 17.0 32.0 27.5 500 130 E4 R74154-500-R-

0.18µF 9.0 17.0 32.0 27.5 500 130 E4 R74184-500-R-

0.22µF 9.0 17.0 32.0 27.5 500 130 E4 R74224-500-R-

0.27µF 10.0 20.0 32.0 27.5 500 130 E4 R74274-500-R-

0.33µF 10.0 20.0 32.0 27.5 500 130 E4 R74334-500-R-

0.39µF 10.0 20.0 32.0 27.5 500 130 E4 R74394-500-R-

0.47µF 11.0 20.0 32.0 27.5 500 130 E4 R74474-500-R-

0.56µF 13.0 22.0 32.0 27.5 500 130 E4 R74564-500-R-

0.68µF 13.0 22.0 32.0 27.5 500 130 E4 R74684-500-R-

0.82µF 14.0 28.0 32.0 27.5 500 130 E4 R74824-500-R-

1.0µF 14.0 28.0 32.0 27.5 500 130 E4 R74105-500-R-

1.2µF 14.0 28.0 32.0 27.5 500 130 E4 R74125-500-R-

1.5µF 18.0 33.0 32.0 27.5 500 130 E4 R74155-500-R-

1.8µF 22.0 37.0 32.0 27.5 500 130 E4 R74185-500-R-

2.2µF 22.0 37.0 32.0 27.5 500 130 E4 R74225-500-R-

0.47µF 11.0 22.0 41.5 37.5 300 78 E4 R74474-500-W-

0.56µF 11.0 22.0 41.5 37.5 300 78 E4 R74564-500-W-

0.68µF 11.0 22.0 41.5 37.5 300 78 E4 R74684-500-W-

0.82µF 13.0 24.0 41.5 37.5 300 78 E4 R74824-500-W-

1.0µF 13.0 24.0 41.5 37.5 300 78 E4 R74105-500-W-

1.2µF 16.0 28.5 41.5 37.5 300 78 E4 R74125-500-W-

1.5µF 16.0 28.5 41.5 37.5 300 78 E4 R74155-500-W-

2.2µF 19.0 32.0 41.5 37.5 300 78 E4 R74225-500-W-

2.7µF 20.0 40.0 41.5 37.5 300 78 E4 R74275-500-W-

3.3µF 20.0 40.0 41.5 37.5 300 78 E4 R74335-500-W-

Tolerance: J (± 5%); K (±10%)

Packaging code: B (bulk); A (ammo); R (reel)

Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3)

Omit for standard (4-6)

Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case

the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The

pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the

above table. The dv/dt test is carried out at 2 times the above values.

single side metallized

polypropylene film

2 section

(500Vac)

NISSEI-ARCOTRONICS R74

MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

A.C. APPLICATIONS

SERIES CODE: R74

Rated

Cap. 700Vac (3 sections) Max

dv/dt Max K0 Part Number

B H L P (V/µs) (V2/µs)

1000ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74102-700-I-

1200ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74122-700-I-

1500ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74152-700-I-

1800ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74182-700-I-

2200ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74222-700-I-

2700ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74272-700-I-

3300ρF 5.0 11.0 18.0 15.0 3000 960 E4 R74332-700-I-

3900ρF 6.0 12.0 18.0 15.0 3000 960 E4 R74392-700-I-

4700ρF 6.0 12.0 18.0 15.0 3000 960 E4 R74472-700-I-

5600ρF 6.0 12.0 18.0 15.0 3000 960 E4 R74562-700-I-

6800ρF 7.5 13.5 18.0 15.0 3000 960 E4 R74682-700-I-

8200ρF 7.5 13.5 18.0 15.0 3000 960 E4 R74822-700-I-

0.010µF 8.5 14.5 18.0 15.0 3000 960 E4 R74103-700-I-

0.012µF 10.0 16.0 18.0 15.0 3000 960 E4 R74123-700-I-

0.015µF 10.0 16.0 18.0 15.0 3000 960 E4 R74153-700-I-

8200ρF 6.0 15.0 26.5 22.5 1300 420 E4 R74822-700-N-

0.010µF 6.0 15.0 26.5 22.5 1300 420 E4 R74103-700-N-

0.012µF 6.0 15.0 26.5 22.5 1300 420 E4 R74123-700-N-

0.015µF 6.0 15.0 26.5 22.5 1300 420 E4 R74153-700-N-

0.018µF 7.0 16.0 26.5 22.5 1300 420 E4 R74183-700-N-

0.022µF 8.5 17.0 26.5 22.5 1300 420 E4 R74223-700-N-

0.027µF 8.5 17.0 26.5 22.5 1300 420 E4 R74273-700-N-

0.033µF 10.0 18.5 26.5 22.5 1300 420 E4 R74333-700-N-

0.039µF 10.0 18.5 26.5 22.5 1300 420 E4 R74393-700-N-

0.047µF 11.0 20.0 26.5 22.5 1300 420 E4 R74473-700-N-

0.068µF 9.0 17.0 32.0 27.5 700 226 E4 R74683-700-R-

0.082µF 9.0 17.0 32.0 27.5 700 226 E4 R74823-700-R-

0.10µF 10.0 20.0 32.0 27.5 700 226 E4 R74104-700-R-

0.12µF 10.0 20.0 32.0 27.5 700 226 E4 R74124-700-R-

0.15µF 10.0 20.0 32.0 27.5 700 226 E4 R74154-700-R-

0.18µF 11.0 20.0 32.0 27.5 700 226 E4 R74184-700-R-

0.22µF 13.0 22.0 32.0 27.5 700 226 E4 R74224-700-R-

0.27µF 14.0 28.0 32.0 27.5 700 226 E4 R74274-700-R-

0.33µF 14.0 28.0 32.0 27.5 700 226 E4 R74334-700-R-

0.39µF 18.0 33.0 32.0 27.5 700 226 E4 R74394-700-R-

0.47µF 18.0 33.0 32.0 27.5 700 226 E4 R74474-700-R-

0.56µF 22.0 37.0 32.0 27.5 700 226 E4 R74564-700-R-

0.68µF 22.0 37.0 32.0 27.5 700 226 E4 R74684-700-R-

0.33µF 11.0 22.0 41.5 37.5 400 130 E4 R74334-700-W-

0.39µF 13.0 24.0 41.5 37.5 400 130 E4 R74394-700-W-

0.47µF 16.0 28.5 41.5 37.5 400 130 E4 R74474-700-W-

0.56µF 16.0 28.5 41.5 37.5 400 130 E4 R74564-700-W-

0.68µF 16.0 28.5 41.5 37.5 400 130 E4 R74684-700-W-

0.82µF 19.0 32.0 41.5 37.5 400 130 E4 R74824-700-W-

1.0µF 19.0 32.0 41.5 37.5 400 130 E4 R74105-700-W-

Tolerance: J (± 5%); K (±10%)

Packaging code: B (bulk); A (ammo); R (reel)

Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3)

Omit for standard (4-6)

All dimensions are in mm.

Note: If the working voltage (V) is lower than the rated voltage (VR), the

capacitor may work at higher dv/dt. In this case the maximum value

allowed is obtained multiplying the above value (see table dv/dt) with

the ratio VR /V. The pulse characteristic K0 depends on the voltage

waveform and in any case it cannot exceed the value given in the

b t bl Th d /dt t t i i d t t 2 ti th b l

Rated

Cap. 900Vac (4 sections) Max

dv/dt Max K0Part Number

B H L P (V/µs) (V2/µs)

1000ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74102-900-N-

1200ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74122-900-N-

1500ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74152-900-N-

1800ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74182-900N-

2200ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74222-900-N-

2700ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74272-900-N-

3300ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74332-900-N-

3900ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74392-900-N-

4700ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74472-900-N-

5600ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74562-900-N-

6800ρF 6.0 15.0 26.5 22.5 2500 1000 E4 R74682-900-N-

8200ρF 7.0 16.0 26.5 22.5 2500 1000 E4 R74822-900-N-

0.010µF 7.0 16.0 26.5 22.5 2500 1000 E4 R74103-900-N-

0.012µF 8.5 17.0 26.5 22.5 2500 1000 E4 R74123-900-N-

0.015µF 10.0 18.5 26.5 22.5 2500 1000 E4 R74153-900-N-

0.018µF 10.0 18.5 26.5 22.5 2500 1000 E4 R74183-900-N-

0.022µF 11.0 20.0 26.5 22.5 2500 1000 E4 R74223-900-N-

0.027µF 9.0 17.0 32.0 27.5 1500 600 E4 R74273-900-R-

0.033µF 9.0 17.0 32.0 27.5 1500 600 E4 R74333-900-R-

0.039µF 9.0 17.0 32.0 27.5 1500 600 E4 R74393-900-R-

0.047µF 9.0 17.0 32.0 27.5 1500 600 E4 R74473-900-R-

0.056µF 9.0 17.0 32.0 27.5 1500 600 E4 R74563-900-R-

0.068µF 9.0 17.0 32.0 27.5 1500 600 E4 R74683-900-R-

0.082µF 10.0 20.0 32.0 27.5 1500 600 E4 R74823-900-R-

0.10µF 10.0 20.0 32.0 27.5 1500 600 E4 R74104-900-R-

0.12µF 11.0 20.0 32.0 27.5 1500 600 E4 R74124-900-R-

0.15µF 13.0 22.0 32.0 27.5 1500 600 E4 R74154-900-R-

0.18µF 14.0 28.0 32.0 27.5 1500 600 E4 R74184-900-R-

0.22µF 14.0 28.0 32.0 27.5 1500 600 E4 R74224-900-R-

0.27µF 18.0 33.0 32.0 27.5 1500 600 E4 R74274-900-R-

0.33µF 18.0 33.0 32.0 27.5 1500 600 E4 R74334-900-R-

0.39µF 22.0 37.0 32.0 27.5 1500 600 E4 R74394-900-R-

0.47µF 22.0 37.0 32.0 27.5 1500 600 E4 R74474-900-R-

0.56µF 22.0 37.0 32.0 27.5 1500 600 E4 R74564-900-R-

0.22µF 11.0 22.0 41.5 37.5 900 360 E4 R74224-900-W-

0.27µF 13.0 24.0 41.5 37.5 900 360 E4 R74274-900-W-

0.33µF 16.0 28.5 41.5 37.5 900 360 E4 R74334-900-W-

0.39µF 16.0 28.5 41.5 37.5 900 360 E4 R74394-900-W-

0.47µF 16.0 28.5 41.5 37.5 900 360 E4 R74474-900-W-

0.56µF 19.0 32.0 41.5 37.5 900 360 E4 R74564-900-W-

0.68µF 19.0 32.0 41.5 37.5 900 360 E4 R74684-900-W-

0.82µF 20.0 40.0 41.5 37.5 900 360 E4 R74824-900-W-

1.0µF 24.0 44.0 41.5 37.5 900 360 E4 R74105-900-W-

Tolerance: J (± 5%); K (±10%)

Packaging code: B (bulk); A (ammo); R (reel)

Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3)

Omit for standard (4-6)

single side metallized

polypropylene film

single side metallized

polypropylene film

3 sections

(700Vac)

4 sections

(900Vac)

NISSEI-ARCOTRONICS R74

MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

A.C. APPLICATIONS

SERIES CODE: R74

ELECTRICAL CHARACTERISTICS

Rated voltage (VR): 250Vac ( 630Vdc) -400Vac (1000Vdc)

500Vac (1300Vdc) -700Vac (1600Vdc)

900Vac (2000Vdc)

Rated temperature (TR): +85°C

Voltage derating vs. temperature:

for temperatures between +85°C and +105°C a decreasing factor

of 1.25% per °C on the rated voltage VR has to be applied.

Capacitance range:

1000ρF to 0.12µF

Capacitance values:

E 12 series (IEC 60063 Norm)

Capacitance tolerances (measured at 1 kHz):

±5% (J); ±10% (K)

Total self-inductance (L): (lead length ~2mm)

Pitch (mm) 10 15 22.5 27.5

L (nH) ≈ 9 10 18 18

Dissipation factor (DF):

tgδ×10-4 at +25°C ± 5°C

kHz C ≤ 0.1µF

100 ≤ 6

≤ 20

Insulation resistance:

Test conditions

Temperature: +25°C ± 5°C

Voltage charge time: 1 min

Voltage charge: 100Vdc

Performance

≥ 1 x 105 MΩ (Typ. value: 5 x 105 MΩ)*

Test voltage between terminations:

1.6×VR applied for 2 s at +25°C ± 5°C

TEST METHOD AND PERFORMANCE

Damp heat, steady state:

Test conditions

Temperature: +40°C ± 2°C

Relative humidity (RH): 93% ± 2%

Test duration: 56 days

Performance

Capacitance change (∆C/C): ≤ 2%

DF change (∆tgδ): ≤ 10×10-4 at 1kHz

Insulation resistance: ≥ 50% of initial limit

Endurance:

Test conditions

Temperature: +85°C ± 2°C

Test duration: 2000 h

Voltage applied: 1.25×VR (a.c.) at 50Hz

Performance

Capacitance change (∆C/C): ≤ 5%

DF change (∆tgδ): ≤ 15×10-4 at 10kHz

Insulation resistance: ≥ 50% of initial limit

Resistance to soldering heat:

Test conditions

Solder bath temperature: +260°C ± 5°C

Dipping time (with heat screen): 10 s ± 1 s

Performance

Capacitance change (∆C/C): ≤ 1%

DF change (∆tgδ): ≤ 10×10-4 at 10kHz

Insulation resistance: ≥ initial limit

Long term stability (after two years):

Storage: standard environmental conditions (see general

information)

Performance

Capacitance change (∆C/C): ≤ 0.5%

NISSEI-ARCOTRONICS R74

MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

A.C. APPLICATIONS

SERIES CODE: R74

MAX. VOLTAGE (Vrms) VERSUS FREQUENCY (sinusoidal waveform / Th ≤ 40°C)

Note: p (pitch) in mm

250 Vac

100

1000

1 10 100 1000

f [kHz]

Vrms [V]

0.015µF - p = 15

0.033µF - p = 15

0.068µF - p = 15

400 Vac

100

1000

1 10 100 1000

f [kHz]

Vrms [V]

0.01µF - p = 15

0.022µF - p = 15

0.1µF - p = 26.5

700 Vac

100

1000

1 10 100 1000

f [kHz]

Vrms [V]

0.001µF - p = 15

0.01µF - p = 15

0.022µF - p = 22.5

500 Vac

100

1000

1 10 100 1000

f [kHz]

Vrms [V]

0.01µF - p = 15

0.033µF - p = 22.5

0.1µF - p = 27.5

900 Vac

100

1000

1 10 100 1000

f [kHz]

Vrms [V]

0.0015µF - p = 22.5

0.0047µF - p = 22.5

0.015µF - p = 22.5