PIC18F2X1X/4X1X 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology Power-Managed Modes: Flexible Oscillator Structure: * * * * * * * * * Four Crystal modes, Up to 40 MHz * 4x Phase Lock Loop (PLL) - Available for Crystal and Internal Oscillators * Two External RC modes, Up to 4 MHz * Two External Clock modes, Up to 40 MHz * Internal Oscillator Block: - 8 user-selectable frequencies, from 31 kHz to 8 MHz - Provides a complete range of clock speeds from 31 kHz to 32 MHz when used with PLL - User-tunable to compensate for frequency drift * Secondary Oscillator using Timer1 @ 32 kHz * Fail-Safe Clock Monitor: - Allows for safe shutdown if peripheral clock stops Run: CPU On, Peripherals On Idle: CPU Off, Peripherals On Sleep: CPU Off, Peripherals Off Idle mode Currents Down to 3.0 A Typical Sleep mode Currents Down to 20 nA Typical Timer1 Oscillator: 1.8 A, 32 kHz, 2V Watchdog Timer: 2.1 A Two-Speed Oscillator Start-up Peripheral Highlights: * High-Current Sink/Source 25 mA/25 mA * Up to 2 Capture/Compare/PWM (CCP) modules, One with Auto-Shutdown (28-pin devices) * Enhanced Capture/Compare/PWM (ECCP) module (40/44-pin devices only): - One, two or four PWM outputs - Selectable polarity - Programmable dead time - Auto-shutdown and auto-restart * Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2CTM Master and Slave modes * Enhanced Addressable USART module: - Supports RS-485, RS-232 and LIN 1.2 - RS-232 operation using internal oscillator block (no external crystal required) - Auto-wake-up on Start bit - Auto-Baud Detect * 10-Bit, Up to 13-Channel Analog-to-Digital Converter module (A/D): - Auto-acquisition capability - Conversion available during Sleep * Dual Analog Comparators with Input Multiplexing * Programmable 16-Level High/Low-Voltage Detection (HLVD) module: - Supports interrupt on High/Low-Voltage Detection (c) 2009 Microchip Technology Inc. Special Microcontroller Features: * C Compiler Optimized Architecture: - Optional extended instruction set designed to optimize re-entrant code * 100,000 Erase/Write Cycle Flash Program Memory Typical * Three Programmable External Interrupts * Four Input Change Interrupts * Priority Levels for Interrupts * 8 x 8 Single-Cycle Hardware Multiplier * Extended Watchdog Timer (WDT): - Programmable period from 4 ms to 131s * Single-Supply 5V In-Circuit Serial ProgrammingTM (ICSPTM) via Two Pins * In-Circuit Debug (ICD) via Two Pins * Wide Operating Voltage Range: 2.0V to 5.5V * Programmable Brown-out Reset (BOR) with Software Enable Option DS39636D-page 3 Program Memory Device Flash (bytes) # Single-Word Instructions Data Memory SRAM (bytes) I/O 10-Bit A/D (ch) CCP/ECCP (PWM) MSSP SPI Master I2CTM EUSART PIC18F2X1X/4X1X Comp. Timers 8/16-Bit PIC18F2410 16K 8192 768 25 10 2/0 Y Y 1 2 1/3 PIC18F2510 32K 16384 1536 25 10 2/0 Y Y 1 2 1/3 PIC18F2515 48K 24576 3968 25 10 2/0 Y Y 1 2 1/3 PIC18F2610 64K 32768 3968 25 10 2/0 Y Y 1 2 1/3 PIC18F4410 16K 8192 768 36 13 1/1 Y Y 1 2 1/3 PIC18F4510 32K 16384 1536 36 13 1/1 Y Y 1 2 1/3 PIC18F4515 48K 24576 3968 36 13 1/1 Y Y 1 2 1/3 PIC18F4610 64K 32768 3968 36 13 1/1 Y Y 1 2 1/3 DS39636D-page 4 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X Pin Diagrams 28-pin SPDIP, SOIC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 RB7/KBI3/PGD RB6//KBI2/PGC RB5/KBI1/PGM RB4/KBI0/AN11 RB3/AN9/CCP2(1) RB2/INT2/AN8 RB1/INT1/AN10 RB0/INT0/FLT0/AN12 VDD VSS RC7/RX/DT RC6/TX/CK RC5/SDO RC4/SDI/SDA RA1/AN1 RA0/AN0 MCLR/VPP/RE3 RB7/KBI3/PGD RB6/KBI2/PGC RB5/KBI1/PGM RB4KBI0/AN11 28-pin QFN 28 27 26 25 24 23 22 21 20 19 18 17 16 15 PIC18F2X1X MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RA4/T0CKI/C1OUT RA5/AN4/SS/HLVDIN/C2OUT VSS OSC1/CLKI/RA7 OSC2/CLKO/RA6 RC0/T1OSO/T13CKI RC1/T1OSI/CCP2(1) RC2/CCP1 RC3/SCK/SCL 28 27 26 25 24 23 22 1 2 3 4 5 6 7 PIC18F2410 PIC18F2510 8 9 10 11 12 13 14 21 20 19 18 17 16 15 RB3/AN9/CCP2(1) RB2/INT2/AN8 RB1/INT1/AN10 RB0/INT0/FLT0/AN12 VDD VSS RC7/RX/DT RC0/T1OSO/T13CKI RC1/T1OSI/CCP2(1) RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RA4/T0CKI/C1OUT RA5/AN4/SS/HLVDIN/C2OUT VSS OSC1/CLKI/RA7 OSC2/CLKO/RA6 MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RA4/T0CKI/C1OUT RA5/AN4/SS/HLVDIN/C2OUT RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 VDD VSS OSC1/CLKI/RA7 OSC2/CLKO/RA6 RC0/T1OSO/T13CKI RC1/T1OSI/CCP2(1) RC2/CCP1/P1A RC3/SCK/SCL RD0/PSP0 RD1/PSP1 Note 1: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PIC18F4X1X 40-pin PDIP 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 RB7/KBI3/PGD RB6/KBI2/PGC RB5/KBI1/PGM RB4/KBI0/AN11 RB3/AN9/CCP2(1) RB2/INT2/AN8 RB1/INT1/AN10 RB0/INT0/FLT0/AN12 VDD VSS RD7/PSP7/P1D RD6/PSP6/P1C RD5/PSP5/P1B RD4/PSP4 RC7/RX/DT RC6/TX/CK RC5/SDO RC4/SDI/SDA RD3/PSP3 RD2/PSP2 RB3 is the alternate pin for CCP2 multiplexing. (c) 2009 Microchip Technology Inc. DS39636D-page 5 PIC18F2X1X/4X1X 44 43 42 41 40 39 38 37 36 35 34 1 2 3 4 5 6 7 8 9 10 11 PIC18F4X1X 33 32 31 30 29 28 27 26 25 24 23 NC RC0/T1OSO/T13CKI OSC2/CLKO/RA6 OSC1/CLKI/RA7 VSS VDD RE2/CS/AN7 RE1/WR/AN6 RE0/RD/AN5 RA5/AN4/SS/HLVDIN/C2OUT RA4/T0CKI/C1OUT 44 43 42 41 40 39 38 37 36 35 34 1 2 3 4 5 6 7 8 9 10 11 PIC18F4X1X 33 32 31 30 29 28 27 26 25 24 23 OSC2/CLKO/RA6 OSC1/CLKI/RA7 VSS VSS VDD VDD RE2/CS/AN7 RE1/WR/AN6 RE0/RD/AN5 RA5/AN4/SS/HLVDIN/C2OUT RA4/T0CKI/C1OUT RB3/AN9/CCP2(1) NC RB4/KBI0/AN11 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RC7/RX/DT RD4/PSP4 RD5/PSP5/P1B RD6/PSP6/P1C RD7/PSP7/P1D VSS VDD VDD RB0/INT0/FLT0/AN12 RB1/INT1/AN10 RB2/INT2/AN8 12 13 14 15 16 17 18 19 20 21 22 44-pin QFN RC6/TX/CK RC5/SDO RC4/SDI/SDA RD3/PSP3 RD2/PSP2 RD1/PSP1 RD0/PSP0 RC3/SCK/SCL RC2/CCP1/P1A RC1/T1OSI/CCP2(1) RC0/T1OSO/T13CKI NC NC RB4/KBI0/AN11 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD MCLR/VPP/RE3 RA0/AN0 RA1/AN1 RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RC7/RX/DT RD4/PSP4 RD5/PSP5/P1B RD6/PSP6/P1C RD7/PSP7/P1D VSS VDD RB0/INT0/FLT0/AN12 RB1/INT1/AN10 RB2/INT2/AN8 RB3/AN9/CCP2(1) 12 13 14 15 16 17 18 19 20 21 22 44-pin TQFP RC6/TX/CK RC5/SDO RC4/SDI/SDA RD3/PSP3 RD2/PSP2 RD1/PSP1 RD0/PSP0 RC3/SCK/SCL RC2/CCP1/P1A RC1/T1OSI/CCP2(1) NC Pin Diagrams (Cont.'d) Note DS39636D-page 6 1: RB3 is the alternate pin for CCP2 multiplexing. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X Table of Contents 1.0 Device Overview .......................................................................................................................................................................... 9 2.0 Oscillator Configurations ............................................................................................................................................................ 25 3.0 Power-Managed Modes ............................................................................................................................................................. 35 4.0 Reset .......................................................................................................................................................................................... 43 5.0 Memory Organization ................................................................................................................................................................. 55 6.0 Flash Program Memory.............................................................................................................................................................. 77 7.0 8 x 8 Hardware Multiplier............................................................................................................................................................ 81 8.0 Interrupts .................................................................................................................................................................................... 83 9.0 I/O Ports ..................................................................................................................................................................................... 97 10.0 Timer0 Module ......................................................................................................................................................................... 115 11.0 Timer1 Module ......................................................................................................................................................................... 119 12.0 Timer2 Module ......................................................................................................................................................................... 125 13.0 Timer3 Module ......................................................................................................................................................................... 127 14.0 Capture/Compare/PWM (CCP) Modules ................................................................................................................................. 131 15.0 Enhanced Capture/Compare/PWM (ECCP) Module................................................................................................................ 139 16.0 Master Synchronous Serial Port (MSSP) Module .................................................................................................................... 153 17.0 Enhanced Universal Synchronous Receiver Transmitter (EUSART)....................................................................................... 193 18.0 10-Bit Analog-to-Digital Converter (A/D) Module ..................................................................................................................... 213 19.0 Comparator Module.................................................................................................................................................................. 223 20.0 Comparator Voltage Reference Module................................................................................................................................... 229 21.0 High/Low-Voltage Detect (HLVD)............................................................................................................................................. 233 22.0 Special Features of the CPU.................................................................................................................................................... 239 23.0 Instruction Set Summary .......................................................................................................................................................... 259 24.0 Development Support............................................................................................................................................................... 309 25.0 Electrical Characteristics .......................................................................................................................................................... 313 26.0 DC and AC Characteristics Graphs And Tables ...................................................................................................................... 351 27.0 Packaging Information.............................................................................................................................................................. 353 Appendix A: Revision History............................................................................................................................................................. 361 Appendix B: Device Differences ........................................................................................................................................................ 361 Appendix C: Conversion Considerations ........................................................................................................................................... 362 Appendix D: Migration From Baseline to Enhanced Devices ............................................................................................................ 362 Appendix E: Migration From Mid-Range to Enhanced Devices ......................................................................................................... 363 Appendix F: Migration From High-End to Enhanced Devices............................................................................................................ 363 Index ................................................................................................................................................................................................. 365 The Microchip Web Site ..................................................................................................................................................................... 375 Customer Change Notification Service .............................................................................................................................................. 375 Customer Support .............................................................................................................................................................................. 375 Reader Response .............................................................................................................................................................................. 376 PIC18F2X1X/4X1X Product Identification System............................................................................................................................. 377 (c) 2009 Microchip Technology Inc. DS39636D-page 7 PIC18F2X1X/4X1X TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. DS39636D-page 8 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 1.0 DEVICE OVERVIEW This document contains device specific information for the following devices: * PIC18F2410 * PIC18LF2410 * PIC18F2510 * PIC18LF2510 * PIC18F2515 * PIC18LF2515 * PIC18F2610 * PIC18LF2610 * PIC18F4410 * PIC18LF4410 * PIC18F4510 * PIC18LF4510 * PIC18F4515 * PIC18LF4515 * PIC18F4610 * PIC18LF4610 This family offers the advantages of all PIC18 microcontrollers - namely, high computational performance at an economical price - with the addition of high-endurance, Flash program memory. On top of these features, the PIC18F2X1X/4X1X family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power sensitive applications. 1.1 1.1.1 New Core Features nanoWatt TECHNOLOGY All of the devices in the PIC18F2X1X/4X1X family incorporate a range of features that can significantly reduce power consumption during operation. Key items include: * Alternate Run Modes: By clocking the controller from the Timer1 source or the internal oscillator block, power consumption during code execution can be reduced by as much as 90%. * Multiple Idle Modes: The controller can also run with its CPU core disabled but the peripherals still active. In these states, power consumption can be reduced even further, to as little as 4% of normal operation requirements. * On-the-fly Mode Switching: The powermanaged modes are invoked by user code during operation, allowing the user to incorporate powersaving ideas into their application's software design. * Lower Consumption in Key Modules: The power requirements for both Timer1 and the Watchdog Timer have been minimized. See Section 25.0 "Electrical Characteristics" for values. (c) 2009 Microchip Technology Inc. 1.1.2 MULTIPLE OSCILLATOR OPTIONS AND FEATURES All of the devices in the PIC18F2X1X/4X1X family offer ten different oscillator options, allowing users a wide range of choices in developing application hardware. These include: * Four Crystal modes, using crystals or ceramic resonators * Two External Clock modes, offering the option of using two pins (oscillator input and a divide-by-4 clock output) or one pin (oscillator input, with the second pin reassigned as general I/O) * Two External RC Oscillator modes with the same pin options as the External Clock modes * An internal oscillator block which provides an 8 MHz clock and an INTRC source (approximately 31 kHz), as well as a range of 6 user selectable clock frequencies, between 125 kHz to 4 MHz, for a total of 8 clock frequencies. This option frees the two oscillator pins for use as additional general purpose I/O. * A Phase Lock Loop (PLL) frequency multiplier, available to both the high-speed crystal and Internal Oscillator modes, which allows clock speeds of up to 40 MHz. Used with the internal oscillator, the PLL gives users a complete selection of clock speeds, from 31 kHz to 32 MHz - all without using an external crystal or clock circuit. Besides its availability as a clock source, the internal oscillator block provides a stable reference source that gives the family additional features for robust operation: * Fail-Safe Clock Monitor: This option constantly monitors the main clock source against a reference signal provided by the internal oscillator. If a clock failure occurs, the controller is switched to the internal oscillator block, allowing for continued low-speed operation or a safe application shutdown. * Two-Speed Start-up: This option allows the internal oscillator to serve as the clock source from Power-on Reset, or wake-up from Sleep mode, until the primary clock source is available. DS39636D-page 9 PIC18F2X1X/4X1X 1.2 Other Special Features * Memory Endurance: The Flash cells for program memory are rated to 100,000 erase/write cycles. Data retention without refresh is conservatively estimated to be greater than 40 years. * Extended Instruction Set: The PIC18F2X1X/ 4X1X family introduces an optional extension to the PIC18 instruction set, which adds 8 new instructions and an Indexed Addressing mode. This extension, enabled as a device configuration option, has been specifically designed to optimize re-entrant application code originally developed in high-level languages, such as C. * Enhanced CCP Module: In PWM mode, this module provides 1, 2 or 4 modulated outputs for controlling half-bridge and full-bridge drivers. Other features include Auto-Shutdown, for disabling PWM outputs on interrupt or other select conditions and Auto-Restart, to reactivate outputs once the condition has cleared. * Enhanced Addressable USART: This serial communication module is capable of standard RS-232 operation and provides support for the LIN bus protocol. Other enhancements include automatic baud rate detection and a 16-bit Baud Rate Generator for improved resolution. When the microcontroller is using the internal oscillator block, the USART provides stable operation for applications that talk to the outside world without using an external crystal (or its accompanying power requirement). * 10-bit A/D Converter: This module incorporates programmable acquisition time, allowing for a channel to be selected and a conversion to be initiated without waiting for a sampling period and thus, reduce code overhead. * Extended Watchdog Timer (WDT): This enhanced version incorporates a 16-bit prescaler, allowing an extended time-out range that is stable across operating voltage and temperature. See Section 25.0 "Electrical Characteristics" for time-out periods. DS39636D-page 10 1.3 Details on Individual Family Members Devices in the PIC18F2X1X/4X1X family are available in 28-pin and 40/44-pin packages. Block diagrams for the two groups are shown in Figure 1-1 and Figure 1-2. The devices are differentiated from each other in five ways: 1. 2. 3. 4. 5. Flash program memory * 16 Kbytes for PIC18F2410/4410 devices * 32 Kbytes for PIC18F2510/4510 devices * 48 Kbytes for PIC18F2515/4515 devices * 64 Kbytes for PIC18F2610/4610 devices A/D channels (10 for 28-pin devices, 13 for 40/44-pin devices). I/O ports (3 bidirectional ports on 28-pin devices, 5 bidirectional ports on 40/44-pin devices). CCP and Enhanced CCP implementation (28-pin devices have 2 standard CCP modules; 40/44-pin devices have one standard CCP module and one ECCP module). Parallel Slave Port (present only on 40/44-pin devices). All other features for devices in this family are identical. These are summarized in Table 1-1. The pinouts for all devices are listed in Table 1-3 and Table 1-4. Like all Microchip PIC18 devices, members of the PIC18F2X1X/4X1X family are available as both standard and low-voltage devices. Standard devices with Flash memory, designated with an "F" in the part number (such as PIC18F2610), accommodate an operating VDD range of 4.2V to 5.5V. Low-voltage parts, designated by "LF" (such as PIC18LF2610), function over an extended VDD range of 2.0V to 5.5V. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 1-1: DEVICE FEATURES (PIC18F2410/2415/2510/2515/2610) Features PIC18F2410 PIC18F2510 PIC18F2515 PIC18F2610 Operating Frequency DC - 40 MHz DC - 40 MHz DC - 40 MHz DC - 40 MHz Program Memory (Bytes) 16384 32768 49152 65536 Program Memory (Instructions) 8192 16384 24576 32768 Data Memory (Bytes) 768 1536 3968 3968 Interrupt Sources I/O Ports 18 18 18 18 Ports A, B, C, (E) Ports A, B, C, (E) Ports A, B, C, (E) Ports A, B, C, (E) Timers 4 4 4 4 Capture/Compare/PWM Modules 2 2 2 2 Enhanced Capture/Compare/PWM Modules 0 0 0 0 MSSP, Enhanced USART MSSP, Enhanced USART MSSP, Enhanced USART MSSP, Enhanced USART Serial Communications Parallel Communications (PSP) No No No No 10-bit Analog-to-Digital Module 10 Input Channels 10 Input Channels 10 Input Channels 10 Input Channels Resets (and Delays) POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT Programmable High/Low-Voltage Detect Yes Yes Yes Yes Programmable Brown-out Reset Yes Yes Yes Yes Instruction Set Packages (c) 2009 Microchip Technology Inc. 75 Instructions; 75 Instructions; 75 Instructions; 75 Instructions; 83 with Extended 83 with Extended 83 with Extended 83 with Extended Instruction Set enabled Instruction Set enabled Instruction Set enabled Instruction Set enabled 28-pin SPDIP 28-pin SOIC 28-pin QFN 28-pin SPDIP 28-pin SOIC 28-pin QFN 28-pin SPDIP 28-pin SOIC 28-pin SPDIP 28-pin SOIC DS39636D-page 11 PIC18F2X1X/4X1X TABLE 1-2: DEVICE FEATURES (PIC18F4410/4415/4510/4515/4610) Features PIC18F4410 PIC18F4510 PIC18F4515 PIC18F4610 Operating Frequency DC - 40 MHz DC - 40 MHz DC - 40 MHz DC - 40 MHz Program Memory (Bytes) 16384 32768 49152 65536 Program Memory (Instructions) 8192 16384 24576 32768 768 1536 3968 3968 Data Memory (Bytes) Interrupt Sources I/O Ports 19 19 19 19 Ports A, B, C, D, E Ports A, B, C, D, E Ports A, B, C, D, E Ports A, B, C, D, E Timers 4 4 4 4 Capture/Compare/PWM Modules 1 1 1 1 Enhanced Capture/Compare/PWM Modules 1 1 1 1 MSSP, Enhanced USART MSSP, Enhanced USART MSSP, Enhanced USART MSSP, Enhanced USART Serial Communications Parallel Communications (PSP) Yes Yes Yes Yes 10-Bit Analog-to-Digital Module 13 Input Channels 13 Input Channels 13 Input Channels 13 Input Channels Resets (and Delays) POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT POR, BOR, RESET Instruction, Stack Full, Stack Underflow (PWRT, OST), MCLR (optional), WDT Programmable High/Low-Voltage Detect Yes Yes Yes Yes Programmable Brown-out Reset Yes Yes Yes Yes Instruction Set Packages DS39636D-page 12 75 Instructions; 75 Instructions; 75 Instructions; 75 Instructions; 83 with Extended 83 with Extended 83 with Extended 83 with Extended Instruction Set enabled Instruction Set enabled Instruction Set enabled Instruction Set enabled 40-pin PDIP 44-pin QFN 44-pin TQFP 40-pin PDIP 44-pin QFN 44-pin TQFP 40-pin PDIP 44-pin QFN 44-pin TQFP 40-pin PDIP 44-pin QFN 44-pin TQFP (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 1-1: PIC18F2410/2415/2510/2515/2610 (28-PIN) BLOCK DIAGRAM Data Bus<8> Table Pointer<21> PCLATU PCLATH 21 PCU PCH PCL Program Counter 31 Level Stack Address Latch Program Memory (16/32/48/64 Kbytes) Data Latch 12 Data Address<12> 4 BSR STKPTR Instruction Bus <16> RA0/AN0 RA1/AN1 RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RA4/T0CKI/C1OUT RA5/AN4/SS/HLVDIN/C2OUT OSC2/CLKO(3)/RA6 OSC1/CLKI(3)/RA7 Address Latch 20 8 PORTA Data Latch Data Memory (.7, 1.5, 3.9 Kbytes) 8 8 inc/dec logic 4 Access Bank 12 FSR0 FSR1 FSR2 12 PORTB RB0/INT0/FLT0/AN12 RB1/INT1/AN10 RB2/INT2/AN8 RB3/AN9/CCP2(1) RB4/KBI0/AN11 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD inc/dec logic Table Latch Address Decode ROM Latch IR Instruction Decode and Control 8 State Machine Control Signals PRODH PRODL 3 Internal Oscillator Block (3) OSC2 T1OSI INTRC Oscillator T1OSO 8 MHz Oscillator Watchdog Timer Brown-out Reset Fail-Safe Clock Monitor Single-Supply Programming In-Circuit Debugger MCLR(2) VDD, VSS BOR HLVD Comparator Note Power-up Timer Oscillator Start-up Timer Power-on Reset CCP1 RC0/T1OSO/T13CKI RC1/T1OSI/CCP2(1) RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RC7/RX/DT 8 W BITOP 8 OSC1(3) PORTC 8 x 8 Multiply 8 8 8 8 ALU<8> 8 Precision Band Gap Reference PORTE MCLR/VPP/RE3(2) Timer0 Timer1 Timer2 Timer3 CCP2 MSSP EUSART ADC 10-bit 1: CCP2 is multiplexed with RC1 when Configuration bit, CCP2MX, is set, or RB3 when CCP2MX is not set. 2: RE3 is only available when MCLR functionality is disabled. 3: OSC1/CLKI and OSC2/CLKO are only available in select oscillator modes and when these pins are not being used as digital I/O. Refer to Section 2.0 "Oscillator Configurations" for additional information. (c) 2009 Microchip Technology Inc. DS39636D-page 13 PIC18F2X1X/4X1X FIGURE 1-2: PIC18F4410/4415/4510/4515/4610 (40/44-PIN) BLOCK DIAGRAM Data Bus<8> Table Pointer<21> PCLATU PCLATH 21 RA0/AN0 RA1/AN1 RA2/AN2/VREF-/CVREF RA3/AN3/VREF+ RA4/T0CKI/C1OUT RA5/AN4/SS/HLVDIN/C2OUT OSC2/CLKO(3)/RA6 OSC1/CLKI(3)/RA7 Data Latch Data Memory (.7, 1.5, 3.9 Kbytes) 8 8 inc/dec logic PORTA Address Latch 20 PCU PCH PCL Program Counter 12 Data Address<12> 31 Level Stack Address Latch Program Memory (16/32/48/64 Kbytes) Data Latch 4 BSR STKPTR 8 12 FSR0 FSR1 FSR2 RB0/INT0/FLT0/AN12 RB1/INT1/AN10 RB2/INT2/AN8 RB3/AN9/CCP2(1) RB4/KBI0/AN11 RB5/KBI1/PGM RB6/KBI2/PGC RB7/KBI3/PGD 4 Access Bank 12 inc/dec logic Table Latch PORTC Address Decode ROM Latch Instruction Bus <16> PORTB RC0/T1OSO/T13CKI RC1/T1OSI/CCP2(1) RC2/CCP1/P1A RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RC7/RX/DT IR 8 State Machine Control Signals Instruction Decode and Control PRODH PRODL 3 8 x 8 Multiply 8 W BITOP 8 OSC1(3) Internal Oscillator Block OSC2(3) INTRC Oscillator T1OSI MCLR(2) Single-Supply Programming VDD, VSS In-Circuit Debugger BOR HLVD Comparator ECCP1 Watchdog Timer Brown-out Reset Fail-Safe Clock Monitor RD0/PSP0 :RD4/PSP4 RD5/PSP5/P1B RD6/PSP6/P1C RD7/PSP7/P1D 8 8 8 ALU<8> Power-on Reset 8 MHz Oscillator T1OSO Note Power-up Timer Oscillator Start-up Timer 8 PORTD 8 PORTE Precision Band Gap Reference Timer0 Timer1 Timer2 Timer3 CCP2 MSSP EUSART ADC 10-bit RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 MCLR/VPP/RE3(2) 1: CCP2 is multiplexed with RC1 when Configuration bit, CCP2MX, is set, or RB3 when CCP2MX is not set. 2: RE3 is only available when MCLR functionality is disabled. 3: OSC1/CLKI and OSC2/CLKO are only available in select oscillator modes and when these pins are not being used as digital I/O. Refer to Section 2.0 "Oscillator Configurations" for additional information. DS39636D-page 14 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 1-3: PIC18F2410/2415/2510/2515/2610 PINOUT I/O DESCRIPTIONS Pin Number Pin Name MCLR/VPP/RE3 MCLR Pin Buffer SPDIP, Type Type QFN SOIC 1 26 VPP RE3 OSC1/CLKI/RA7 OSC1 9 6 I ST P I ST ST O -- CLKO O -- RA6 I/O TTL RA7 OSC2/CLKO/RA6 OSC2 10 Master Clear (input) or programming voltage (input). Master Clear (Reset) input. This pin is an active-low Reset to the device. Programming voltage input. Digital input. Oscillator crystal or external clock input. Oscillator crystal input or external clock source input. ST buffer when configured in RC mode; CMOS otherwise. I CMOS External clock source input. Always associated with pin function OSC1. (See related OSC1/CLKI, OSC2/CLKO pins.) I/O TTL General purpose I/O pin. I CLKI Description 7 Oscillator crystal or clock output. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. In RC mode, OSC2 pin outputs CLKO, which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. General purpose I/O pin. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. (c) 2009 Microchip Technology Inc. DS39636D-page 15 PIC18F2X1X/4X1X TABLE 1-3: PIC18F2410/2415/2510/2515/2610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Number Pin Name Pin Buffer SPDIP, Type Type QFN SOIC Description PORTA is a bidirectional I/O port. RA0/AN0 RA0 AN0 2 RA1/AN1 RA1 AN1 3 RA2/AN2/VREF-/CVREF RA2 AN2 VREFCVREF 4 RA3/AN3/VREF+ RA3 AN3 VREF+ 5 RA4/T0CKI/C1OUT RA4 T0CKI C1OUT 6 RA5/AN4/SS/HLVDIN/ C2OUT RA5 AN4 SS HLVDIN C2OUT 7 27 I/O TTL I Analog Digital I/O. Analog input 0. I/O TTL I Analog Digital I/O. Analog input 1. I/O TTL I Analog I Analog O Analog Digital I/O. Analog input 2. A/D reference voltage (low) input. Comparator reference voltage output. I/O TTL I Analog I Analog Digital I/O. Analog input 3. A/D reference voltage (high) input. I/O I O Digital I/O. Timer0 external clock input. Comparator 1 output. 28 1 2 3 ST ST -- 4 I/O TTL I Analog I TTL I Analog O -- Digital I/O. Analog input 4. SPI slave select input. High/Low-Voltage Detect input. Comparator 2 output. RA6 See the OSC2/CLKO/RA6 pin. RA7 See the OSC1/CLKI/RA7 pin. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. DS39636D-page 16 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 1-3: PIC18F2410/2415/2510/2515/2610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Number Pin Name Pin Buffer SPDIP, Type Type QFN SOIC Description PORTB is a bidirectional I/O port. PORTB can be software programmed for internal weak pull-ups on all inputs. RB0/INT0/FLT0/AN12 RB0 INT0 FLT0 AN12 21 RB1/INT1/AN10 RB1 INT1 AN10 22 RB2/INT2/AN8 RB2 INT2 AN8 23 RB3/AN9/CCP2 RB3 AN9 CCP2(1) 24 RB4/KBI0/AN11 RB4 KBI0 AN11 25 RB5/KBI1/PGM RB5 KBI1 PGM 26 RB6/KBI2/PGC RB6 KBI2 PGC 27 RB7/KBI3/PGD RB7 KBI3 PGD 28 18 I/O TTL I ST I ST I Analog Digital I/O. External interrupt 0. PWM Fault input for CCP1. Analog input 12. 19 I/O TTL I ST I Analog Digital I/O. External interrupt 1. Analog input 10. I/O TTL I ST I Analog Digital I/O. External interrupt 2. Analog input 8. I/O TTL I Analog I/O ST Digital I/O. Analog input 9. Capture 2 input/Compare 2 output/PWM 2 output. I/O TTL I TTL I Analog Digital I/O. Interrupt-on-change pin. Analog input 11. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. Low-Voltage ICSPTM Programming enable pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming clock pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming data pin. 20 21 22 23 24 25 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. (c) 2009 Microchip Technology Inc. DS39636D-page 17 PIC18F2X1X/4X1X TABLE 1-3: PIC18F2410/2415/2510/2515/2610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Number Pin Name Pin Buffer SPDIP, Type Type QFN SOIC Description PORTC is a bidirectional I/O port. RC0/T1OSO/T13CKI RC0 T1OSO T13CKI 11 8 RC1/T1OSI/CCP2 RC1 T1OSI CCP2(2) 12 RC2/CCP1 RC2 CCP1 13 RC3/SCK/SCL RC3 SCK SCL 14 RC4/SDI/SDA RC4 SDI SDA 15 RC5/SDO RC5 SDO 16 RC6/TX/CK RC6 TX CK 17 RC7/RX/DT RC7 RX DT 18 RE3 -- -- VSS 8, 19 5, 16 P -- Ground reference for logic and I/O pins. VDD 20 17 P -- Positive supply for logic and I/O pins. I/O O I ST -- ST Digital I/O. Timer1 oscillator output. Timer1/Timer3 external clock input. 9 I/O ST I Analog I/O ST Digital I/O. Timer1 oscillator input. Capture 2 input/Compare 2 output/PWM 2 output. I/O I/O ST ST Digital I/O. Capture 1 input/Compare 1 output/PWM 1 output. I/O I/O I/O ST ST ST Digital I/O. Synchronous serial clock input/output for SPI mode. Synchronous serial clock input/output for I2CTM mode. I/O I I/O ST ST ST Digital I/O. SPI data in. I2C data I/O. I/O O ST -- Digital I/O. SPI data out. I/O O I/O ST -- ST Digital I/O. EUSART asynchronous transmit. EUSART synchronous clock (see related RX/DT). I/O I I/O ST ST ST Digital I/O. EUSART asynchronous receive. EUSART synchronous data (see related TX/CK). -- -- 10 11 12 13 14 15 See MCLR/VPP/RE3 pin. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. DS39636D-page 18 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 1-4: PIC18F4410/4415/4510/4515/4610 PINOUT I/O DESCRIPTIONS Pin Name MCLR/VPP/RE3 MCLR Pin Number PDIP 1 Pin Buffer Type Type QFN TQFP 18 18 VPP RE3 OSC1/CLKI/RA7 OSC1 13 32 ST P I ST 30 I CLKI I RA7 OSC2/CLKO/RA6 OSC2 I I/O 14 33 Description Master Clear (input) or programming voltage (input). Master Clear (Reset) input. This pin is an active-low Reset to the device. Programming voltage input. Digital input. Oscillator crystal or external clock input. Oscillator crystal input or external clock source input. ST buffer when configured in RC mode; analog otherwise. CMOS External clock source input. Always associated with pin function OSC1. (See related OSC1/CLKI, OSC2/CLKO pins.) TTL General purpose I/O pin. ST 31 O -- CLKO O -- RA6 I/O TTL Oscillator crystal or clock output. Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. In RC mode, OSC2 pin outputs CLKO, which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. General purpose I/O pin. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. (c) 2009 Microchip Technology Inc. DS39636D-page 19 PIC18F2X1X/4X1X TABLE 1-4: PIC18F4410/4415/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP Pin Buffer Type Type QFN TQFP Description PORTA is a bidirectional I/O port. RA0/AN0 RA0 AN0 2 RA1/AN1 RA1 AN1 3 RA2/AN2/VREF-/CVREF RA2 AN2 VREFCVREF 4 RA3/AN3/VREF+ RA3 AN3 VREF+ 5 RA4/T0CKI/C1OUT RA4 T0CKI C1OUT 6 RA5/AN4/SS/HLVDIN/ C2OUT RA5 AN4 SS HLVDIN C2OUT 7 19 20 21 22 23 24 19 I/O I TTL Analog Digital I/O. Analog input 0. I/O I TTL Analog Digital I/O. Analog input 1. I/O I I O TTL Analog Analog Analog Digital I/O. Analog input 2. A/D reference voltage (low) input. Comparator reference voltage output. I/O I I TTL Analog Analog Digital I/O. Analog input 3. A/D reference voltage (high) input. I/O I O ST ST -- I/O I I I O TTL Analog TTL Analog -- 20 21 22 23 Digital I/O. Timer0 external clock input. Comparator 1 output. 24 Digital I/O. Analog input 4. SPI slave select input. High/Low-Voltage Detect input. Comparator 2 output. RA6 See the OSC2/CLKO/RA6 pin. RA7 See the OSC1/CLKI/RA7 pin. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. DS39636D-page 20 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 1-4: PIC18F4410/4415/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP Pin Buffer QFN TQFP Type Type Description PORTB is a bidirectional I/O port. PORTB can be software programmed for internal weak pull-ups on all inputs. RB0/INT0/FLT0/AN12 RB0 INT0 FLT0 AN12 33 RB1/INT1/AN10 RB1 INT1 AN10 34 RB2/INT2/AN8 RB2 INT2 AN8 35 RB3/AN9/CCP2 RB3 AN9 CCP2(1) 36 RB4/KBI0/AN11 RB4 KBI0 AN11 37 RB5/KBI1/PGM RB5 KBI1 PGM 38 RB6/KBI2/PGC RB6 KBI2 PGC 39 RB7/KBI3/PGD RB7 KBI3 PGD 40 9 10 11 12 14 15 16 17 8 I/O I I I TTL ST ST Analog Digital I/O. External interrupt 0. PWM Fault input for Enhanced CCP1. Analog input 12. I/O I I TTL ST Analog Digital I/O. External interrupt 1. Analog input 10. I/O I I TTL ST Analog Digital I/O. External interrupt 2. Analog input 8. I/O I I/O TTL Analog ST Digital I/O. Analog input 9. Capture 2 input/Compare 2 output/PWM 2 output. I/O I I TTL TTL Analog Digital I/O. Interrupt-on-change pin. Analog input 11. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. Low-Voltage ICSPTM Programming enable pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming clock pin. I/O I I/O TTL TTL ST Digital I/O. Interrupt-on-change pin. In-Circuit Debugger and ICSP programming data pin. 9 10 11 14 15 16 17 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. (c) 2009 Microchip Technology Inc. DS39636D-page 21 PIC18F2X1X/4X1X TABLE 1-4: PIC18F4410/4415/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Name Pin Number PDIP Pin Buffer Type Type QFN TQFP Description PORTC is a bidirectional I/O port. RC0/T1OSO/T13CKI RC0 T1OSO T13CKI 15 RC1/T1OSI/CCP2 RC1 T1OSI CCP2(2) 16 RC2/CCP1/P1A RC2 CCP1 P1A 17 RC3/SCK/SCL RC3 SCK 18 34 35 36 37 32 23 RC5/SDO RC5 SDO 24 RC6/TX/CK RC6 TX CK 25 RC7/RX/DT RC7 RX DT 26 42 43 44 1 ST -- ST I/O I I/O ST CMOS ST I/O I/O O ST ST -- Digital I/O. Capture1 input/Compare1 output/PWM1 output. Enhanced CCP1 output. I/O I/O ST ST I/O ST Digital I/O. Synchronous serial clock input/output for SPI mode. Synchronous serial clock input/output for I2CTM mode. I/O I I/O ST ST ST Digital I/O. SPI data in. I2C data I/O. I/O O ST -- Digital I/O. SPI data out. I/O O I/O ST -- ST Digital I/O. EUSART asynchronous transmit. EUSART synchronous clock (see related RX/DT). I/O I I/O ST ST ST Digital I/O. EUSART asynchronous receive. EUSART synchronous data (see related TX/CK). Digital I/O. Timer1 oscillator output. Timer1/Timer3 external clock input. 35 Digital I/O. Timer1 oscillator input. Capture 2 input/Compare 2 output/PWM 2 output. 36 37 SCL RC4/SDI/SDA RC4 SDI SDA I/O O I 42 43 44 1 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. DS39636D-page 22 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 1-4: Pin Name PIC18F4410/4415/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Number PDIP Pin Buffer QFN TQFP Type Type Description PORTD is a bidirectional I/O port or a Parallel Slave Port (PSP) for interfacing to a microprocessor port. These pins have TTL input buffers when PSP module is enabled. RD0/PSP0 RD0 PSP0 19 RD1/PSP1 RD1 PSP1 20 RD2/PSP2 RD2 PSP2 21 RD3/PSP3 RD3 PSP3 22 RD4/PSP4 RD4 PSP4 27 RD5/PSP5/P1B RD5 PSP5 P1B 28 RD6/PSP6/P1C RD6 PSP6 P1C 29 RD7/PSP7/P1D RD7 PSP7 P1D 30 38 39 40 41 2 3 4 5 38 I/O I/O ST TTL Digital I/O. Parallel Slave Port data. I/O I/O ST TTL Digital I/O. Parallel Slave Port data. I/O I/O ST TTL Digital I/O. Parallel Slave Port data. I/O I/O ST TTL Digital I/O. Parallel Slave Port data. I/O I/O ST TTL Digital I/O. Parallel Slave Port data. I/O I/O O ST TTL -- Digital I/O. Parallel Slave Port data. Enhanced CCP1 output. I/O I/O O ST TTL -- Digital I/O. Parallel Slave Port data. Enhanced CCP1 output. I/O I/O O ST TTL -- Digital I/O. Parallel Slave Port data. Enhanced CCP1 output. 39 40 41 2 3 4 5 Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. (c) 2009 Microchip Technology Inc. DS39636D-page 23 PIC18F2X1X/4X1X TABLE 1-4: Pin Name PIC18F4410/4415/4510/4515/4610 PINOUT I/O DESCRIPTIONS (CONTINUED) Pin Number PDIP Pin Buffer Type Type QFN TQFP Description PORTE is a bidirectional I/O port. RE0/RD/AN5 RE0 RD 8 25 25 I/O I ST TTL I Analog I/O I ST TTL I Analog I/O I ST TTL I Analog -- -- -- See MCLR/VPP/RE3 pin. 6, 29 P -- Ground reference for logic and I/O pins. 7, 8, 7, 28 28, 29 P -- Positive supply for logic and I/O pins. -- -- No connect. AN5 RE1/WR/AN6 RE1 WR 9 26 26 AN6 RE2/CS/AN7 RE2 CS 10 27 -- -- VSS 12, 31 6, 30, 31 VDD 11, 32 NC -- 13 Digital I/O. Write control for Parallel Slave Port (see CS and RD pins). Analog input 6. 27 AN7 RE3 Digital I/O. Read control for Parallel Slave Port (see also WR and CS pins). Analog input 5. 12, 13, 33, 34 Digital I/O. Chip select control for Parallel Slave Port (see related RD and WR). Analog input 7. Legend: TTL = TTL compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels I = Input O = Output P = Power Note 1: Default assignment for CCP2 when Configuration bit, CCP2MX, is set. 2: Alternate assignment for CCP2 when Configuration bit, CCP2MX, is cleared. DS39636D-page 24 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 2.0 OSCILLATOR CONFIGURATIONS 2.1 Oscillator Types PIC18F2X1X/4X1X devices can be operated in ten different oscillator modes. The user can program the Configuration bits, FOSC3:FOSC0, in Configuration Register 1H to select one of these ten modes: 1. 2. 3. 4. LP XT HS HSPLL Low-Power Crystal Crystal/Resonator High-Speed Crystal/Resonator High-Speed Crystal/Resonator with PLL enabled 5. RC External Resistor/Capacitor with FOSC/4 output on RA6 6. RCIO External Resistor/Capacitor with I/O on RA6 7. INTIO1 Internal Oscillator with FOSC/4 output on RA6 and I/O on RA7 8. INTIO2 Internal Oscillator with I/O on RA6 and RA7 9. EC External Clock with FOSC/4 output 10. ECIO External Clock with I/O on RA6 2.2 Crystal Oscillator/Ceramic Resonators In XT, LP, HS or HSPLL Oscillator modes, a crystal or ceramic resonator is connected to the OSC1 and OSC2 pins to establish oscillation. Figure 2-1 shows the pin connections. The oscillator design requires the use of a parallel cut crystal. Note: Use of a series cut crystal may give a frequency out of the crystal manufacturer's specifications. FIGURE 2-1: C1(1) OSC1 XTAL C2(1) To Internal Logic RF(3) Sleep RS(2) PIC18FXXXX OSC2 Note 1: See Table 2-1 and Table 2-2 for initial values of C1 and C2. 2: A series resistor (RS) may be required for AT strip cut crystals. 3: RF varies with the oscillator mode chosen. TABLE 2-1: CAPACITOR SELECTION FOR CERAMIC RESONATORS Typical Capacitor Values Used: Mode Freq OSC1 OSC2 XT 3.58 MHz 4.19 MHz 4 MHz 4 MHz 15 pF 15 pF 30 pF 50 pF 15 pF 15 pF 30 pF 50 pF Capacitor values are for design guidance only. Different capacitor values may be required to produce acceptable oscillator operation. The user should test the performance of the oscillator over the expected VDD and temperature range for the application. See the notes following Table 2-2 for additional information. Note: (c) 2009 Microchip Technology Inc. CRYSTAL/CERAMIC RESONATOR OPERATION (XT, LP, HS OR HSPLL CONFIGURATION) When using resonators with frequencies above 3.5 MHz, the use of HS mode, rather than XT mode, is recommended. HS mode may be used at any VDD for which the controller is rated. If HS is selected, it is possible that the gain of the oscillator will overdrive the resonator. Therefore, a series resistor should be placed between the OSC2 pin and the resonator. As a good starting point, the recommended value of RS is 330. DS39636D-page 25 PIC18F2X1X/4X1X TABLE 2-2: Osc Type CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR Crystal Freq Typical Capacitor Values Tested: C1 C2 LP 32 kHz 30 pF 30 pF XT 1 MHz 4 MHz 15 pF 15 pF 15 pF 15 pF HS 4 MHz 10 MHz 20 MHz 25 MHz 15 pF 15 pF 15 pF 15 pF 15 pF 15 pF 15 pF 15 pF Capacitor values are for design guidance only. Different capacitor values may be required to produce acceptable oscillator operation. The user should test the performance of the oscillator over the expected VDD and temperature range for the application. See the notes following this table for additional information. Note 1: Higher capacitance increases the stability of the oscillator but also increases the start-up time. 2: When operating below 3V VDD, or when using certain ceramic resonators at any voltage, it may be necessary to use the HS mode or switch to a crystal oscillator. 3: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 4: Rs may be required to avoid overdriving crystals with low drive level specification. 5: Always verify oscillator performance over the VDD and temperature range that is expected for the application. An external clock source may also be connected to the OSC1 pin in the HS mode, as shown in Figure 2-2. FIGURE 2-2: EXTERNAL CLOCK INPUT OPERATION (HS OSCILLATOR CONFIGURATION) OSC1 Clock from Ext. System PIC18FXXXX Open 2.3 External Clock Input The EC and ECIO Oscillator modes require an external clock source to be connected to the OSC1 pin. There is no oscillator start-up time required after a Power-on Reset or after an exit from Sleep mode. In the EC Oscillator mode, the oscillator frequency divided by 4 is available on the OSC2 pin. This signal may be used for test purposes or to synchronize other logic. Figure 2-3 shows the pin connections for the EC Oscillator mode. FIGURE 2-3: EXTERNAL CLOCK INPUT OPERATION (EC CONFIGURATION) OSC1/CLKI Clock from Ext. System PIC18FXXXX FOSC/4 OSC2/CLKO The ECIO Oscillator mode functions like the EC mode, except that the OSC2 pin becomes an additional general purpose I/O pin. The I/O pin becomes bit 6 of PORTA (RA6). Figure 2-4 shows the pin connections for the ECIO Oscillator mode. FIGURE 2-4: EXTERNAL CLOCK INPUT OPERATION (ECIO CONFIGURATION) OSC1/CLKI Clock from Ext. System PIC18FXXXX RA6 DS39636D-page 26 (HS Mode) OSC2 I/O (OSC2) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 2.4 RC Oscillator 2.5 For timing insensitive applications, the "RC" and "RCIO" device options offer additional cost savings. The actual oscillator frequency is a function of several factors: * supply voltage * values of the external resistor (REXT) and capacitor (CEXT) * operating temperature Given the same device, operating voltage and temperature and component values, there will also be unit-to-unit frequency variations. These are due to factors such as: * normal manufacturing variation * difference in lead frame capacitance between package types (especially for low CEXT values) * variations within the tolerance of limits of REXT and CEXT In the RC Oscillator mode, the oscillator frequency divided by 4 is available on the OSC2 pin. This signal may be used for test purposes or to synchronize other logic. Figure 2-5 shows how the R/C combination is connected. FIGURE 2-5: PLL Frequency Multiplier A Phase Locked Loop (PLL) circuit is provided as an option for users who wish to use a lower frequency oscillator circuit or to clock the device up to its highest rated frequency from a crystal oscillator. This may be useful for customers who are concerned with EMI due to high-frequency crystals or users who require higher clock speeds from an internal oscillator. 2.5.1 The HSPLL mode makes use of the HS mode oscillator for frequencies up to 10 MHz. A PLL then multiplies the oscillator output frequency by 4 to produce an internal clock frequency up to 40 MHz. The PLLEN bit is not available in this oscillator mode. The PLL is only available to the crystal oscillator when the FOSC3:FOSC0 Configuration bits are programmed for HSPLL mode (= 0110). FIGURE 2-7: PLL BLOCK DIAGRAM (HS MODE) HS Oscillator Enable PLL Enable (from Configuration Register 1H) RC OSCILLATOR MODE VDD HSPLL OSCILLATOR MODE OSC2 REXT OSC1 Internal Clock HS Mode OSC1 Crystal Osc FIN FOUT Loop Filter CEXT PIC18FXXXX VSS FOSC/4 OSC2/CLKO /4 The RCIO Oscillator mode (Figure 2-6) functions like the RC mode, except that the OSC2 pin becomes an additional general purpose I/O pin. The I/O pin becomes bit 6 of PORTA (RA6). RCIO OSCILLATOR MODE VDD REXT OSC1 Internal Clock VCO MUX Recommended values: 3 k REXT 100 k CEXT > 20 pF FIGURE 2-6: Phase Comparator 2.5.2 SYSCLK PLL AND INTOSC The PLL is also available to the internal oscillator block in selected oscillator modes. In this configuration, the PLL is enabled in software and generates a clock output of up to 32 MHz. The operation of INTOSC with the PLL is described in Section 2.6.4 "PLL in INTOSC Modes". CEXT PIC18FXXXX VSS RA6 I/O (OSC2) Recommended values: 3 k REXT 100 k CEXT > 20 pF (c) 2009 Microchip Technology Inc. DS39636D-page 27 PIC18F2X1X/4X1X 2.6 Internal Oscillator Block The PIC18F2X1X/4X1X devices include an internal oscillator block which generates two different clock signals; either can be used as the microcontroller's clock source. This may eliminate the need for external oscillator circuits on the OSC1 and/or OSC2 pins. The main output (INTOSC) is an 8 MHz clock source, which can be used to directly drive the device clock. It also drives a postscaler, which can provide a range of clock frequencies from 31 kHz to 4 MHz. The INTOSC output is enabled when a clock frequency from 125 kHz to 8 MHz is selected. The other clock source is the internal RC oscillator (INTRC), which provides a nominal 31 kHz output. INTRC is enabled if it is selected as the device clock source; it is also enabled automatically when any of the following are enabled: * * * * Power-up Timer Fail-Safe Clock Monitor Watchdog Timer Two-Speed Start-up These features are discussed in greater detail in Section 22.0 "Special Features of the CPU". The clock source frequency (INTOSC direct, INTRC direct or INTOSC postscaler) is selected by configuring the IRCF bits of the OSCCON register (page 32). 2.6.1 INTIO MODES Using the internal oscillator as the clock source eliminates the need for up to two external oscillator pins, which can then be used for digital I/O. Two distinct configurations are available: * In INTIO1 mode, the OSC2 pin outputs FOSC/4, while OSC1 functions as RA7 for digital input and output. * In INTIO2 mode, OSC1 functions as RA7 and OSC2 functions as RA6, both for digital input and output. 2.6.2 INTOSC OUTPUT FREQUENCY The internal oscillator block is calibrated at the factory to produce an INTOSC output frequency of 8.0 MHz. The INTRC oscillator operates independently of the INTOSC source. Any changes in INTOSC across voltage and temperature are not necessarily reflected by changes in INTRC and vice versa. 2.6.3 OSCTUNE REGISTER The internal oscillator's output has been calibrated at the factory but can be adjusted in the user's application. This is done by writing to the OSCTUNE register (Register 2-1). The tuning sensitivity is constant throughout the tuning range. DS39636D-page 28 When the OSCTUNE register is modified, the INTOSC frequency will begin shifting to the new frequency. The INTRC clock will reach the new frequency within 8 clock cycles (approximately 8 * 32 s = 256 s). The INTOSC clock will stabilize within 1 ms. Code execution continues during this shift. There is no indication that the shift has occurred. The OSCTUNE register also implements the INTSRC and PLLEN bits, which control certain features of the internal oscillator block. The INTSRC bit allows users to select which internal oscillator provides the clock source when the 31 kHz frequency option is selected. This is covered in greater detail in Section 2.7.1 "Oscillator Control Register". The PLLEN bit controls the operation of the frequency multiplier, PLL, in Internal Oscillator modes. 2.6.4 PLL IN INTOSC MODES The 4x frequency multiplier can be used with the internal oscillator block to produce faster device clock speeds than are normally possible with an internal oscillator. When enabled, the PLL produces a clock speed of up to 32 MHz. Unlike HSPLL mode, the PLL is controlled through software. The control bit, PLLEN (OSCTUNE<6>), is used to enable or disable its operation. The PLL is available when the device is configured to use the internal oscillator block as its primary clock source (FOSC3:FOSC0 = 1001 or 1000). Additionally, the PLL will only function when the selected output frequency is either 4 MHz or 8 MHz (OSCCON<6:4> = 111 or 110). If both of these conditions are not met, the PLL is disabled. The PLLEN control bit is only functional in those internal Oscillator modes where the PLL is available. In all other modes, it is forced to `0' and is effectively unavailable. 2.6.5 INTOSC FREQUENCY DRIFT The factory calibrates the internal oscillator block output (INTOSC) for 8 MHz. However, this frequency may drift as VDD or temperature changes, which can affect the controller operation in a variety of ways. It is possible to adjust the INTOSC frequency by modifying the value in the OSCTUNE register. This has no effect on the INTRC clock source frequency. Tuning the INTOSC source requires knowing when to make the adjustment, in which direction it should be made and in some cases, how large a change is needed. Three compensation techniques are discussed in Section 2.6.5.1 "Compensating with the USART", Section 2.6.5.2 "Compensating with the Timers" and Section 2.6.5.3 "Compensating with the CCP Module in Capture Mode", but other techniques may be used. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 2-1: OSCTUNE: OSCILLATOR TUNING REGISTER R/W-0 R/W-0(1) U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 INTSRC PLLEN(1) -- TUN4 TUN3 TUN2 TUN1 TUN0 bit 7 bit 0 bit 7 INTSRC: Internal Oscillator Low-Frequency Source Select bit 1 = 31.25 kHz device clock derived from 8 MHz INTOSC source (divide-by-256 enabled) 0 = 31 kHz device clock derived directly from INTRC internal oscillator bit 6 PLLEN: Frequency Multiplier PLL for INTOSC Enable bit(1) 1 = PLL enabled for INTOSC (4 MHz and 8 MHz only) 0 = PLL disabled Note 1: Available only in certain oscillator configurations; otherwise, this bit is unavailable and reads as `0'. See Section 2.6.4 "PLL in INTOSC Modes" for details. bit 5 Unimplemented: Read as `0' bit 4-0 TUN4:TUN0: Frequency Tuning bits 01111 = Maximum frequency * * * * 00001 00000 = Center frequency. Oscillator module is running at the calibrated frequency. 11111 * * * * 10000 = Minimum frequency Legend: R = Readable bit -n = Value at POR 2.6.5.1 W = Writable bit `1' = Bit is set Compensating with the USART An adjustment may be required when the USART begins to generate framing errors or receives data with errors while in Asynchronous mode. Framing errors indicate that the device clock frequency is too high; to adjust for this, decrement the value in OSCTUNE to reduce the clock frequency. On the other hand, errors in data may suggest that the clock speed is too low; to compensate, increment OSCTUNE to increase the clock frequency. 2.6.5.2 Compensating with the Timers This technique compares device clock speed to some reference clock. Two timers may be used; one timer is clocked by the peripheral clock, while the other is clocked by a fixed reference source, such as the Timer1 oscillator. Both timers are cleared, but the timer clocked by the reference generates interrupts. When an interrupt occurs, the internally clocked timer is read and both timers are cleared. If the internally clocked timer value is greater than expected, then the internal oscillator block is running too fast. To adjust for this, decrement the OSCTUNE register. (c) 2009 Microchip Technology Inc. 2.6.5.3 U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown Compensating with the CCP Module in Capture Mode A CCP module can use free running Timer1 (or Timer3), clocked by the internal oscillator block and an external event with a known period (i.e., AC power frequency). The time of the first event is captured in the CCPRxH:CCPRxL registers and is recorded for use later. When the second event causes a capture, the time of the first event is subtracted from the time of the second event. Since the period of the external event is known, the time difference between events can be calculated. If the measured time is much greater than the calculated time, the internal oscillator block is running too fast; to compensate, decrement the OSCTUNE register. If the measured time is much less than the calculated time, the internal oscillator block is running too slow; to compensate, increment the OSCTUNE register. DS39636D-page 29 PIC18F2X1X/4X1X 2.7 Clock Sources and Oscillator Switching Like previous PIC18 devices, the PIC18F2X1X/4X1X family includes a feature that allows the device clock source to be switched from the main oscillator to an alternate low-frequency clock source. PIC18F2X1X/ 4X1X devices offer two alternate clock sources. When an alternate clock source is enabled, the various power-managed operating modes are available. Essentially, there are three clock sources for these devices: * Primary oscillators * Secondary oscillators * Internal oscillator block PIC18F2X1X/4X1X devices offer the Timer1 oscillator as a secondary oscillator. This oscillator, in all powermanaged modes, is often the time base for functions such as a real-time clock. Most often, a 32.768 kHz watch crystal is connected between the RC0/T1OSO/T13CKI and RC1/T1OSI pins. Like the LP mode oscillator circuit, loading capacitors are also connected from each pin to ground. The Timer1 oscillator is discussed in greater detail in Section 11.3 "Timer1 Oscillator". The primary oscillators include the External Crystal and Resonator modes, the External RC modes, the External Clock modes and the internal oscillator block. The particular mode is defined by the FOSC3:FOSC0 Configuration bits. The details of these modes are covered earlier in this chapter. FIGURE 2-8: The secondary oscillators are those external sources not connected to the OSC1 or OSC2 pins. These sources may continue to operate even after the controller is placed in a power-managed mode. In addition to being a primary clock source, the internal oscillator block is available as a power-managed mode clock source. The INTRC source is also used as the clock source for several special features, such as the WDT and Fail-Safe Clock Monitor. The clock sources for the PIC18F2X1X/4X1X devices are shown in Figure 2-8. See Section 22.0 "Special Features of the CPU" for Configuration register details. PIC18F2X1X/4X1X CLOCK DIAGRAM PIC18F2X1X/4X1X Primary Oscillator LP, XT, HS, RC, EC OSC2 Sleep 4 x PLL OSC1 HSPLL, INTOSC/PLL OSCTUNE<6> T1OSC T1OSO OSCCON<6:4> 8 MHz OSCCON<6:4> INTRC Source 2 MHz 8 MHz (INTOSC) 31 kHz (INTRC) Postscaler Internal Oscillator Block 8 MHz Source 4 MHz 1 MHz 500 kHz 250 kHz 125 kHz Internal Oscillator CPU 111 110 IDLEN 101 100 011 MUX T1OSI T1OSCEN Enable Oscillator Peripherals MUX Secondary Oscillator 010 001 1 31 kHz 000 0 Clock Control FOSC3:FOSC0 OSCCON<1:0> Clock Source Option for other Modules OSCTUNE<7> WDT, PWRT, FSCM and Two-Speed Start-up DS39636D-page 30 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 2.7.1 OSCILLATOR CONTROL REGISTER The OSCCON register (Register 2-2) controls several aspects of the device clock's operation, both in full power operation and in power-managed modes. The System Clock Select bits, SCS1:SCS0, select the clock source. The available clock sources are the primary clock (defined by the FOSC3:FOSC0 Configuration bits), the secondary clock (Timer1 oscillator) and the internal oscillator block. The clock source changes immediately after one or more of the bits is written to, following a brief clock transition interval. The SCS bits are cleared on all forms of Reset. The Internal Oscillator Frequency Select bits (IRCF2:IRCF0) select the frequency output of the internal oscillator block to drive the device clock. The choices are the INTRC source, the INTOSC source (8 MHz) or one of the frequencies derived from the INTOSC postscaler (31.25 kHz to 4 MHz). If the internal oscillator block is supplying the device clock, changing the states of these bits will have an immediate change on the internal oscillator's output. On device Resets, the default output frequency of the internal oscillator block is set at 1 MHz. When a nominal output frequency of 31 kHz is selected (IRCF2:IRCF0 = 000), users may choose which internal oscillator acts as the source. This is done with the INTSRC bit in the OSCTUNE register (OSCTUNE<7>). Setting this bit selects INTOSC as a 31.25 kHz clock source by enabling the divide-by-256 output of the INTOSC postscaler. Clearing INTSRC selects INTRC (nominally 31 kHz) as the clock source. The IDLEN bit determines if the device goes into Sleep mode or one of the Idle modes when the SLEEP instruction is executed. The use of the flag and control bits in the OSCCON register is discussed in more detail in Section 3.0 "Power-Managed Modes". Note 1: The Timer1 oscillator must be enabled to select the secondary clock source. The Timer1 oscillator is enabled by setting the T1OSCEN bit in the Timer1 Control register (T1CON<3>). If the Timer1 oscillator is not enabled, then any attempt to select a secondary clock source will be ignored. 2: It is recommended that the Timer1 oscillator be operating and stable before selecting the secondary clock source or a very long delay may occur while the Timer1 oscillator starts. 2.7.2 OSCILLATOR TRANSITIONS PIC18F2X1X/4X1X devices contain circuitry to prevent clock "glitches" when switching between clock sources. A short pause in the device clock occurs during the clock switch. The length of this pause is the sum of two cycles of the old clock source and three to four cycles of the new clock source. This formula assumes that the new clock source is stable. Clock transitions are discussed in greater detail in Section 3.1.2 "Entering Power-Managed Modes". This option allows users to select the tunable and more precise INTOSC as a clock source, while maintaining power savings with a very low clock speed. Regardless of the setting of INTSRC, INTRC always remains the clock source for features such as the Watchdog Timer and the Fail-Safe Clock Monitor. The OSTS, IOFS and T1RUN bits indicate which clock source is currently providing the device clock. The OSTS bit indicates that the Oscillator Start-up Timer has timed out and the primary clock is providing the device clock in Primary Clock modes. The IOFS bit indicates when the internal oscillator block has stabilized and is providing the device clock in RC Clock modes. The T1RUN bit (T1CON<6>) indicates when the Timer1 oscillator is providing the device clock in Secondary Clock modes. In power-managed modes, only one of these three bits will be set at any time. If none of these bits are set, the INTRC is providing the clock or the internal oscillator block has just started and is not yet stable. (c) 2009 Microchip Technology Inc. DS39636D-page 31 PIC18F2X1X/4X1X REGISTER 2-2: OSCCON: OSCILLATOR CONTROL REGISTER R/W-0 R/W-1 R/W-0 R/W-0 R(1) R-0 R/W-0 R/W-0 IDLEN IRCF2 IRCF1 IRCF0 OSTS IOFS SCS1 SCS0 bit 7 bit 0 bit 7 IDLEN: Idle Enable bit 1 = Device enters Idle mode on SLEEP instruction 0 = Device enters Sleep mode on SLEEP instruction bit 6-4 IRCF2:IRCF0: Internal Oscillator Frequency Select bits 111 = 8 MHz (INTOSC drives clock directly) 110 = 4 MHz 101 = 2 MHz 100 = 1 MHz(3) 011 = 500 kHz 010 = 250 kHz 001 = 125 kHz 000 = 31 kHz (from either INTOSC/256 or INTRC directly)(2) bit 3 OSTS: Oscillator Start-up Time-out Status bit(1) 1 = Oscillator start-up time-out timer has expired; primary oscillator is running 0 = Oscillator start-up time-out timer is running; primary oscillator is not ready bit 2 IOFS: INTOSC Frequency Stable bit 1 = INTOSC frequency is stable 0 = INTOSC frequency is not stable bit 1-0 SCS1:SCS0: System Clock Select bits 1x = Internal oscillator block 01 = Secondary (Timer1) oscillator 00 = Primary oscillator Note 1: Reset state depends on state of the IESO Configuration bit. 2: Source selected by the INTSRC bit (OSCTUNE<7>), see text. 3: Default output frequency of INTOSC on Reset. Legend: DS39636D-page 32 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 2.8 Effects of Power-Managed Modes on the Various Clock Sources When PRI_IDLE mode is selected, the designated primary oscillator continues to run without interruption. For all other power-managed modes, the oscillator using the OSC1 pin is disabled. The OSC1 pin (and OSC2 pin, if used by the oscillator) will stop oscillating. In Secondary Clock modes (SEC_RUN and SEC_IDLE), the Timer1 oscillator is operating and providing the device clock. The Timer1 oscillator may also run in all power-managed modes if required to clock Timer1 or Timer3. In Internal Oscillator modes (RC_RUN and RC_IDLE), the internal oscillator block provides the device clock source. The 31 kHz INTRC output can be used directly to provide the clock and may be enabled to support various special features, regardless of the powermanaged mode (see Section 22.2 "Watchdog Timer (WDT)", Section 22.3 "Two-Speed Start-up" and Section 22.4 "Fail-Safe Clock Monitor" for more information on WDT, Fail-Safe Clock Monitor and TwoSpeed Start-up). The INTOSC output at 8 MHz may be used directly to clock the device or may be divided down by the postscaler. The INTOSC output is disabled if the clock is provided directly from the INTRC output. If the Sleep mode is selected, all clock sources are stopped. Since all the transistor switching currents have been stopped, Sleep mode achieves the lowest current consumption of the device (only leakage currents). Enabling any on-chip feature that will operate during Sleep will increase the current consumed during Sleep. The INTRC is required to support WDT operation. The Timer1 oscillator may be operating to support a real- TABLE 2-3: time clock. Other features may be operating that do not require a device clock source (i.e., SSP slave, PSP, INTn pins and others). Peripherals that may add significant current consumption are listed in Section 25.2 "DC Characteristics". 2.9 Power-up Delays Power-up delays are controlled by two timers, so that no external Reset circuitry is required for most applications. The delays ensure that the device is kept in Reset until the device power supply is stable under normal circumstances and the primary clock is operating and stable. For additional information on power-up delays, see Section 4.5 "Device Reset Timers". The first timer is the Power-up Timer (PWRT), which provides a fixed delay on power-up (parameter 33, Table 25-10). It is enabled by clearing (= 0) the PWRTEN Configuration bit. The second timer is the Oscillator Start-up Timer (OST), intended to keep the chip in Reset until the crystal oscillator is stable (LP, XT and HS modes). The OST does this by counting 1024 oscillator cycles before allowing the oscillator to clock the device. When the HSPLL Oscillator mode is selected, the device is kept in Reset for an additional 2 ms, following the HS mode OST delay, so the PLL can lock to the incoming clock frequency. There is a delay of interval TCSD (parameter 38, Table 25-10), following POR, while the controller becomes ready to execute instructions. This delay runs concurrently with any other delays. This may be the only delay that occurs when any of the EC, RC or INTIO modes are used as the primary clock source. OSC1 AND OSC2 PIN STATES IN SLEEP MODE Oscillator Mode OSC1 Pin OSC2 Pin RC, INTIO1 Floating, external resistor should pull high At logic low (clock/4 output) RCIO Floating, external resistor should pull high Configured as PORTA, bit 6 INTIO2 Configured as PORTA, bit 7 Configured as PORTA, bit 6 ECIO Floating, pulled by external clock Configured as PORTA, bit 6 EC Floating, pulled by external clock At logic low (clock/4 output) LP, XT and HS Feedback inverter disabled at quiescent voltage level Feedback inverter disabled at quiescent voltage level Note: See Table 4-2 in Section 4.0 "Reset" for time-outs due to Sleep and MCLR Reset. (c) 2009 Microchip Technology Inc. DS39636D-page 33 PIC18F2X1X/4X1X NOTES: DS39636D-page 34 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 3.0 POWER-MANAGED MODES 3.1.1 The SCS1:SCS0 bits allow the selection of one of three clock sources for power-managed modes. They are: PIC18F2X1X/4X1X devices offer a total of seven operating modes for more efficient power management. These modes provide a variety of options for selective power conservation in applications where resources may be limited (i.e., battery-powered devices). * the primary clock, as defined by the FOSC3:FOSC0 Configuration bits * the secondary clock (the Timer1 oscillator) * the internal oscillator block (for RC modes) There are three categories of power-managed modes: * Run modes * Idle modes * Sleep mode 3.1.2 The power-managed modes include several powersaving features offered on previous PIC(R) devices. One is the clock switching feature, offered in other PIC18 devices, allowing the controller to use the Timer1 oscillator in place of the primary oscillator. Also included is the Sleep mode, offered by all PIC devices, where all device clocks are stopped. Entry to the power-managed Idle or Sleep modes is triggered by the execution of a SLEEP instruction. The actual mode that results depends on the status of the IDLEN bit. Depending on the current mode and the mode being switched to, a change to a power-managed mode does not always require setting all of these bits. Many transitions may be done by changing the oscillator select bits, or changing the IDLEN bit, prior to issuing a SLEEP instruction. If the IDLEN bit is already configured correctly, it may only be necessary to perform a SLEEP instruction to switch to the desired mode. Selecting Power-Managed Modes Selecting a power-managed mode requires two decisions: if the CPU is to be clocked or not and the selection of a clock source. The IDLEN bit (OSCCON<7>) controls CPU clocking, while the SCS1:SCS0 bits (OSCCON<1:0>) select the clock source. The individual modes, bit settings, clock sources and affected modules are summarized in Table 3-1. TABLE 3-1: POWER-MANAGED MODES OSCCON Bits Mode IDLEN(1) SCS1:SCS0 <7> <1:0> Sleep ENTERING POWER-MANAGED MODES Switching from one power-managed mode to another begins by loading the OSCCON register. The SCS1:SCS0 bits select the clock source and determine which Run or Idle mode is to be used. Changing these bits causes an immediate switch to the new clock source, assuming that it is running. The switch may also be subject to clock transition delays. These are discussed in Section 3.1.3 "Clock Transitions and Status Indicators" and subsequent sections. These categories define which portions of the device are clocked and sometimes, what speed. The Run and Idle modes may use any of the three available clock sources (primary, secondary or internal oscillator block); the Sleep mode does not use a clock source. 3.1 CLOCK SOURCES Module Clocking CPU Peripherals Available Clock and Oscillator Source 0 N/A Off Off PRI_RUN N/A 00 Clocked Clocked Primary - LP, XT, HS, HSPLL, RC, EC and Internal Oscillator Block(2). This is the normal full power execution mode. SEC_RUN N/A 01 Clocked Clocked Secondary - Timer1 Oscillator RC_RUN N/A 1x Clocked Clocked Internal Oscillator Block(2) PRI_IDLE 1 00 Off Clocked Primary - LP, XT, HS, HSPLL, RC, EC SEC_IDLE 1 01 Off Clocked Secondary - Timer1 Oscillator RC_IDLE 1 1x Off Clocked Internal Oscillator Block(2) Note 1: 2: None - All clocks are disabled IDLEN reflects its value when the SLEEP instruction is executed. Includes INTOSC and INTOSC postscaler, as well as the INTRC source. (c) 2009 Microchip Technology Inc. DS39636D-page 35 PIC18F2X1X/4X1X 3.1.3 CLOCK TRANSITIONS AND STATUS INDICATORS The length of the transition between clock sources is the sum of two cycles of the old clock source and three to four cycles of the new clock source. This formula assumes that the new clock source is stable. Three bits indicate the current clock source and its status. They are: * OSTS (OSCCON<3>) * IOFS (OSCCON<2>) * T1RUN (T1CON<6>) In general, only one of these bits will be set while in a given power-managed mode. When the OSTS bit is set, the primary clock is providing the device clock. When the IOFS bit is set, the INTOSC output is providing a stable 8 MHz clock source to a divider that actually drives the device clock. When the T1RUN bit is set, the Timer1 oscillator is providing the clock. If none of these bits are set, then either the INTRC clock source is clocking the device, or the INTOSC source is not yet stable. If the internal oscillator block is configured as the primary clock source by the FOSC3:FOSC0 Configuration bits, then both the OSTS and IOFS bits may be set when in PRI_RUN or PRI_IDLE modes. This indicates that the primary clock (INTOSC output) is generating a stable 8 MHz output. Entering another power-managed RC mode at the same frequency would clear the OSTS bit. Note 1: Caution should be used when modifying a single IRCF bit. If VDD is less than 3V, it is possible to select a higher clock speed than is supported by the low VDD. Improper device operation may result if the VDD/FOSC specifications are violated. 2: Executing a SLEEP instruction does not necessarily place the device into Sleep mode. It acts as the trigger to place the controller into either the Sleep mode or one of the Idle modes, depending on the setting of the IDLEN bit. 3.1.4 MULTIPLE SLEEP COMMANDS The power-managed mode that is invoked with the SLEEP instruction is determined by the setting of the IDLEN bit at the time the instruction is executed. If another SLEEP instruction is executed, the device will enter the power-managed mode specified by IDLEN at that time. If IDLEN has changed, the device will enter the new power-managed mode specified by the new setting. DS39636D-page 36 3.2 Run Modes In the Run modes, clocks to both the core and peripherals are active. The difference between these modes is the clock source. 3.2.1 PRI_RUN MODE The PRI_RUN mode is the normal, full power execution mode of the microcontroller. This is also the default mode upon a device Reset, unless Two-Speed Start-up is enabled (see Section 22.3 "Two-Speed Start-up" for details). In this mode, the OSTS bit is set. The IOFS bit may be set if the internal oscillator block is the primary clock source (see Section 2.7.1 "Oscillator Control Register"). 3.2.2 SEC_RUN MODE The SEC_RUN mode is the compatible mode to the "clock switching" feature offered in other PIC18 devices. In this mode, the CPU and peripherals are clocked from the Timer1 oscillator. This gives users the option of lower power consumption while still using a high accuracy clock source. SEC_RUN mode is entered by setting the SCS1:SCS0 bits to `01'. The device clock source is switched to the Timer1 oscillator (see Figure 3-1), the primary oscillator is shut down, the T1RUN bit (T1CON<6>) is set and the OSTS bit is cleared. Note: The Timer1 oscillator should already be running prior to entering SEC_RUN mode. If the T1OSCEN bit is not set when the SCS1:SCS0 bits are set to `01', entry to SEC_RUN mode will not occur. If the Timer1 oscillator is enabled but not yet running, device clocks will be delayed until the oscillator has started. In such situations, initial oscillator operation is far from stable and unpredictable operation may result. On transitions from SEC_RUN mode to PRI_RUN, the peripherals and CPU continue to be clocked from the Timer1 oscillator while the primary clock is started. When the primary clock becomes ready, a clock switch back to the primary clock occurs (see Figure 3-2). When the clock switch is complete, the T1RUN bit is cleared, the OSTS bit is set and the primary clock is providing the clock. The IDLEN and SCS bits are not affected by the wake-up; the Timer1 oscillator continues to run. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 3-1: TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE Q1 Q2 Q3 Q4 Q1 Q2 1 T1OSI 2 3 n-1 Q3 Q4 Q1 Q2 Q3 n (1) Clock Transition OSC1 CPU Clock Peripheral Clock Program Counter Note 1: PC PC + 2 PC + 4 Clock transition typically occurs within 2-4 TOSC. FIGURE 3-2: TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 T1OSI OSC1 TOST(1) TPLL(1) 1 PLL Clock Output 2 n-1 n Clock (2) Transition CPU Clock Peripheral Clock Program Counter SCS1:SCS0 bits changed Note 1: 2: 3.2.3 PC + 2 PC PC + 4 OSTS bit set TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. Clock transition typically occurs within 2-4 TOSC. RC_RUN MODE In RC_RUN mode, the CPU and peripherals are clocked from the internal oscillator block using the INTOSC multiplexer. In this mode, the primary clock is shut down. When using the INTRC source, this mode provides the best power conservation of all the Run modes, while still executing code. It works well for user applications which are not highly timing sensitive or do not require high-speed clocks at all times. If the primary clock source is the internal oscillator block (either INTRC or INTOSC), there are no distinguishable differences between PRI_RUN and RC_RUN modes during execution. However, a clock switch delay will occur during entry to and exit from RC_RUN mode. Therefore, if the primary clock source is the internal oscillator block, the use of RC_RUN mode is not recommended. (c) 2009 Microchip Technology Inc. This mode is entered by setting SCS1 to `1'. Although it is ignored, it is recommended that SCS0 also be cleared; this is to maintain software compatibility with future devices. When the clock source is switched to the INTOSC multiplexer (see Figure 3-3), the primary oscillator is shut down and the OSTS bit is cleared. The IRCF bits may be modified at any time to immediately change the clock speed. Note: Caution should be used when modifying a single IRCF bit. If VDD is less than 3V, it is possible to select a higher clock speed than is supported by the low VDD. Improper device operation may result if the VDD/FOSC specifications are violated. DS39636D-page 37 PIC18F2X1X/4X1X If the IRCF bits and the INTSRC bit are all clear, the INTOSC output is not enabled and the IOFS bit will remain clear; there will be no indication of the current clock source. The INTRC source is providing the device clocks. On transitions from RC_RUN mode to PRI_RUN mode, the device continues to be clocked from the INTOSC multiplexer while the primary clock is started. When the primary clock becomes ready, a clock switch to the primary clock occurs (see Figure 3-4). When the clock switch is complete, the IOFS bit is cleared, the OSTS bit is set and the primary clock is providing the device clock. The IDLEN and SCS bits are not affected by the switch. The INTRC source will continue to run if either the WDT or the Fail-Safe Clock Monitor is enabled. If the IRCF bits are changed from all clear (thus, enabling the INTOSC output) or if INTSRC is set, the IOFS bit becomes set after the INTOSC output becomes stable. Clocks to the device continue while the INTOSC source stabilizes after an interval of TIOBST. If the IRCF bits were previously at a non-zero value, or if INTSRC was set before setting SCS1 and the INTOSC source was already stable, the IOFS bit will remain set. FIGURE 3-3: TRANSITION TIMING TO RC_RUN MODE Q1 Q2 Q3 Q4 Q1 Q2 1 INTRC 2 3 n-1 Q3 Q4 Q1 Q2 Q3 n (1) Clock Transition OSC1 CPU Clock Peripheral Clock Program Counter Note 1: PC PC + 2 PC + 4 Clock transition typically occurs within 2-4 TOSC. FIGURE 3-4: TRANSITION TIMING FROM RC_RUN MODE TO PRI_RUN MODE Q1 Q2 Q3 Q4 Q2 Q3 Q4 Q1 Q2 Q3 Q1 INTOSC Multiplexer OSC1 TOST(1) TPLL(1) 1 PLL Clock Output 2 n-1 n (2) Clock Transition CPU Clock Peripheral Clock Program Counter SCS1:SCS0 bits changed Note 1: 2: DS39636D-page 38 PC + 2 PC PC + 4 OSTS bit set TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. Clock transition typically occurs within 2-4 TOSC. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 3.3 Sleep Mode 3.4 The power-managed Sleep mode in the PIC18F2X1X/ 4X1X devices is identical to the legacy Sleep mode offered in all other PIC devices. It is entered by clearing the IDLEN bit (the default state on device Reset) and executing the SLEEP instruction. This shuts down the selected oscillator (Figure 3-5). All clock source status bits are cleared. Idle Modes The Idle modes allow the controller's CPU to be selectively shut down while the peripherals continue to operate. Selecting a particular Idle mode allows users to further manage power consumption. If the IDLEN bit is set to a `1' when a SLEEP instruction is executed, the peripherals will be clocked from the clock source selected using the SCS1:SCS0 bits; however, the CPU will not be clocked. The clock source status bits are not affected. Setting IDLEN and executing a SLEEP instruction provides a quick method of switching from a given Run mode to its corresponding Idle mode. Entering the Sleep mode from any other mode does not require a clock switch. This is because no clocks are needed once the controller has entered Sleep. If the WDT is selected, the INTRC source will continue to operate. If the Timer1 oscillator is enabled, it will also continue to run. If the WDT is selected, the INTRC source will continue to operate. If the Timer1 oscillator is enabled, it will also continue to run. When a wake event occurs in Sleep mode (by interrupt, Reset or WDT time-out), the device will not be clocked until the clock source selected by the SCS1:SCS0 bits becomes ready (see Figure 3-6), or it will be clocked from the internal oscillator block if either the Two-Speed Start-up or the Fail-Safe Clock Monitor are enabled (see Section 22.0 "Special Features of the CPU"). In either case, the OSTS bit is set when the primary clock is providing the device clocks. The IDLEN and SCS bits are not affected by the wake-up. Since the CPU is not executing instructions, the only exits from any of the Idle modes are by interrupt, WDT time-out or a Reset. When a wake event occurs, CPU execution is delayed by an interval of TCSD (parameter 38, Table 25-10) while it becomes ready to execute code. When the CPU begins executing code, it resumes with the same clock source for the current Idle mode. For example, when waking from RC_IDLE mode, the internal oscillator block will clock the CPU and peripherals (in other words, RC_RUN mode). The IDLEN and SCS bits are not affected by the wake-up. While in any Idle mode or the Sleep mode, a WDT timeout will result in a WDT wake-up to the Run mode currently specified by the SCS1:SCS0 bits. FIGURE 3-5: TRANSITION TIMING FOR ENTRY TO SLEEP MODE Q1 Q2 Q3 Q4 Q1 OSC1 CPU Clock Peripheral Clock Sleep Program Counter PC FIGURE 3-6: PC + 2 TRANSITION TIMING FOR WAKE FROM SLEEP (HSPLL) Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 OSC1 TOST(1) PLL Clock Output TPLL(1) CPU Clock Peripheral Clock Program Counter PC Wake Event PC + 2 PC + 4 PC + 6 OSTS bit set Note1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. (c) 2009 Microchip Technology Inc. DS39636D-page 39 PIC18F2X1X/4X1X 3.4.1 PRI_IDLE MODE 3.4.2 This mode is unique among the three low-power Idle modes, in that it does not disable the primary device clock. For timing sensitive applications, this allows for the fastest resumption of device operation with its more accurate primary clock source, since the clock source does not have to "warm up" or transition from another oscillator. PRI_IDLE mode is entered from PRI_RUN mode by setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, set IDLEN first, then clear the SCS bits and execute SLEEP. Although the CPU is disabled, the peripherals continue to be clocked from the primary clock source specified by the FOSC3:FOSC0 Configuration bits. The OSTS bit remains set (see Figure 3-7). In SEC_IDLE mode, the CPU is disabled but the peripherals continue to be clocked from the Timer1 oscillator. This mode is entered from SEC_RUN by setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, set IDLEN first, then set SCS1:SCS0 to `01' and execute SLEEP. When the clock source is switched to the Timer1 oscillator, the primary oscillator is shut down, the OSTS bit is cleared and the T1RUN bit is set. When a wake event occurs, the peripherals continue to be clocked from the Timer1 oscillator. After an interval of TCSD following the wake event, the CPU begins executing code being clocked by the Timer1 oscillator. The IDLEN and SCS bits are not affected by the wake-up; the Timer1 oscillator continues to run (see Figure 3-8). When a wake event occurs, the CPU is clocked from the primary clock source. A delay of interval TCSD is required between the wake event and when code execution starts. This is required to allow the CPU to become ready to execute instructions. After the wakeup, the OSTS bit remains set. The IDLEN and SCS bits are not affected by the wake-up (see Figure 3-8). FIGURE 3-7: SEC_IDLE MODE Note: The Timer1 oscillator should already be running prior to entering SEC_IDLE mode. If the T1OSCEN bit is not set when the SLEEP instruction is executed, the SLEEP instruction will be ignored and entry to SEC_IDLE mode will not occur. If the Timer1 oscillator is enabled but not yet running, peripheral clocks will be delayed until the oscillator has started. In such situations, initial oscillator operation is far from stable and unpredictable operation may result. TRANSITION TIMING FOR ENTRY TO IDLE MODE Q1 Q3 Q2 Q4 Q1 OSC1 CPU Clock Peripheral Clock Program Counter PC FIGURE 3-8: PC + 2 TRANSITION TIMING FOR WAKE FROM IDLE TO RUN MODE Q1 Q2 Q3 Q4 OSC1 TCSD CPU Clock Peripheral Clock Program Counter PC Wake Event DS39636D-page 40 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 3.4.3 RC_IDLE MODE In RC_IDLE mode, the CPU is disabled but the peripherals continue to be clocked from the internal oscillator block using the INTOSC multiplexer. This mode allows for controllable power conservation during Idle periods. From RC_RUN, this mode is entered by setting the IDLEN bit and executing a SLEEP instruction. If the device is in another Run mode, first set IDLEN, then set the SCS1 bit and execute SLEEP. Although its value is ignored, it is recommended that SCS0 also be cleared; this is to maintain software compatibility with future devices. The INTOSC multiplexer may be used to select a higher clock frequency by modifying the IRCF bits before executing the SLEEP instruction. When the clock source is switched to the INTOSC multiplexer, the primary oscillator is shut down and the OSTS bit is cleared. If the IRCF bits are set to any non-zero value, or the INTSRC bit is set, the INTOSC output is enabled. The IOFS bit becomes set, after the INTOSC output becomes stable, after an interval of TIOBST (parameter 39, Table 25-10). Clocks to the peripherals continue while the INTOSC source stabilizes. If the IRCF bits were previously at a non-zero value, or INTSRC was set before the SLEEP instruction was executed and the INTOSC source was already stable, the IOFS bit will remain set. If the IRCF bits and INTSRC are all clear, the INTOSC output will not be enabled, the IOFS bit will remain clear and there will be no indication of the current clock source. When a wake event occurs, the peripherals continue to be clocked from the INTOSC multiplexer. After a delay of TCSD following the wake event, the CPU begins executing code being clocked by the INTOSC multiplexer. The IDLEN and SCS bits are not affected by the wake-up. The INTRC source will continue to run if either the WDT or the Fail-Safe Clock Monitor is enabled. 3.5 Exiting Idle and Sleep Modes An exit from Sleep mode or any of the Idle modes is triggered by an interrupt, a Reset or a WDT time-out. This section discusses the triggers that cause exits from power-managed modes. The clocking subsystem actions are discussed in each of the power-managed modes (see Section 3.2 "Run Modes", Section 3.3 "Sleep Mode" and Section 3.4 "Idle Modes"). 3.5.1 EXIT BY INTERRUPT Any of the available interrupt sources can cause the device to exit from an Idle mode or the Sleep mode to a Run mode. To enable this functionality, an interrupt source must be enabled by setting its enable bit in one of the INTCON or PIE registers. The exit sequence is initiated when the corresponding interrupt flag bit is set. (c) 2009 Microchip Technology Inc. On all exits from Idle or Sleep modes by interrupt, code execution branches to the interrupt vector if the GIE/ GIEH bit (INTCON<7>) is set. Otherwise, code execution continues or resumes without branching (see Section 8.0 "Interrupts"). A fixed delay of interval TCSD following the wake event is required when leaving Sleep and Idle modes. This delay is required for the CPU to prepare for execution. Instruction execution resumes on the first clock cycle following this delay. 3.5.2 EXIT BY WDT TIME-OUT A WDT time-out will cause different actions depending on which power-managed mode the device is in when the time-out occurs. If the device is not executing code (all Idle modes and Sleep mode), the time-out will result in an exit from the powe-managed mode (see Section 3.2 "Run Modes" and Section 3.3 "Sleep Mode"). If the device is executing code (all Run modes), the time-out will result in a WDT Reset (see Section 22.2 "Watchdog Timer (WDT)"). The WDT timer and postscaler are cleared by executing a SLEEP or CLRWDT instruction, the loss of a currently selected clock source (if the Fail-Safe Clock Monitor is enabled) and modifying the IRCF bits in the OSCCON register if the internal oscillator block is the device clock source. 3.5.3 EXIT BY RESET Normally, the device is held in Reset by the Oscillator Start-up Timer (OST) until the primary clock becomes ready. At that time, the OSTS bit is set and the device begins executing code. If the internal oscillator block is the new clock source, the IOFS bit is set instead. The exit delay time from Reset to the start of code execution depends on both the clock sources before and after the wake-up and the type of oscillator if the new clock source is the primary clock. Exit delays are summarized in Table 3-2. Code execution can begin before the primary clock becomes ready. If either the Two-Speed Start-up (see Section 22.3 "Two-Speed Start-up") or Fail-Safe Clock Monitor (see Section 22.4 "Fail-Safe Clock Monitor") is enabled, the device may begin execution as soon as the Reset source has cleared. Execution is clocked by the INTOSC multiplexer driven by the internal oscillator block. Execution is clocked by the internal oscillator block until either the primary clock becomes ready or a power-managed mode is entered before the primary clock becomes ready; the primary clock is then shut down. DS39636D-page 41 PIC18F2X1X/4X1X 3.5.4 EXIT WITHOUT AN OSCILLATOR START-UP DELAY Certain exits from power-managed modes do not invoke the OST at all. There are two cases: * PRI_IDLE mode, where the primary clock source is not stopped; and * the primary clock source is not any of the LP, XT, HS or HSPLL modes. TABLE 3-2: In these instances, the primary clock source either does not require an oscillator start-up delay since it is already running (PRI_IDLE), or normally does not require an oscillator start-up delay (RC, EC and INTIO Oscillator modes). However, a fixed delay of interval TCSD following the wake event is still required when leaving Sleep and Idle modes to allow the CPU to prepare for execution. Instruction execution resumes on the first clock cycle following this delay. EXIT DELAY ON WAKE-UP BY RESET FROM SLEEP MODE OR ANY IDLE MODE (BY CLOCK SOURCES) Clock Source before Wake-up Clock Source after Wake-up Exit Delay Clock Ready Status bit (OSCCON) LP, XT, HS Primary Device Clock (PRI_IDLE mode) OSTS HSPLL EC, RC TCSD(2) INTRC(1) -- INTOSC(3) T1OSC or INTRC(1) INTOSC(3) None (Sleep mode) LP, XT, HS HSPLL TOST + trc(4) OSTS EC, RC INTOSC(2) TCSD(2) TIOBST(5) IOFS LP, XT, HS TOST(5) HSPLL TOST + trc(4) 3: 4: 5: OSTS EC, RC TCSD(2) INTOSC(2) None LP, XT, HS TOST(4) HSPLL TOST + trc(4) OSTS EC, RC TCSD(2) TIOBST(5) IOFS INTOSC(2) Note 1: 2: IOFS TOST(4) IOFS In this instance, refers specifically to the 31 kHz INTRC clock source. TCSD (parameter 38) is a required delay when waking from Sleep and all Idle modes and runs concurrently with any other required delays (see Section 3.4 "Idle Modes"). On Reset, INTOSC defaults to 1 MHz. Includes both the INTOSC 8 MHz source and postscaler derived frequencies. TOST is the Oscillator Start-up Timer (parameter 32). trc is the PLL Lock-out Timer (parameter F12); it is also designated as TPLL. Execution continues during TIOBST (parameter 39), the INTOSC stabilization period. DS39636D-page 42 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 4.0 RESET The PIC18F2X1X/4X1X devices differentiate between various kinds of Reset: a) b) c) d) e) f) g) h) Power-on Reset (POR) MCLR Reset during normal operation MCLR Reset during power-managed modes Watchdog Timer (WDT) Reset (during execution) Programmable Brown-out Reset (BOR) RESET Instruction Stack Full Reset Stack Underflow Reset This section discusses Resets generated by MCLR, POR and BOR and covers the operation of the various start-up timers. Stack Reset events are covered in Section 5.1.2.4 "Stack Full and Underflow Resets". WDT Resets are covered in Section 22.2 "Watchdog Timer (WDT)". FIGURE 4-1: A simplified block diagram of the On-Chip Reset Circuit is shown in Figure 4-1. 4.1 RCON Register Device Reset events are tracked through the RCON register (Register 4-1). The lower five bits of the register indicate that a specific Reset event has occurred. In most cases, these bits can only be cleared by the event and must be set by the application after the event. The state of these flag bits, taken together, can be read to indicate the type of Reset that just occurred. This is described in more detail in Section 4.6 "Reset State of Registers". The RCON register also has control bits for setting interrupt priority (IPEN) and software control of the BOR (SBOREN). Interrupt priority is discussed in Section 8.0 "Interrupts". BOR is covered in Section 4.4 "Brown-out Reset (BOR)". SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT RESET Instruction Stack Full/Underflow Reset Stack Pointer External Reset MCLR MCLRE ( )_IDLE Sleep WDT Time-out VDD Rise Detect POR Pulse VDD Brown-out Reset BOREN S OST/PWRT OST 1024 Cycles 10-bit Ripple Counter OSC1 32 s INTRC(1) PWRT Chip_Reset R Q 65.5 ms 11-bit Ripple Counter Enable PWRT Enable OST(2) Note 1: 2: This is the INTRC source from the internal oscillator block and is separate from the RC oscillator of the CLKI pin. See Table 4-2 for time-out situations. (c) 2009 Microchip Technology Inc. DS39636D-page 43 PIC18F2X1X/4X1X REGISTER 4-1: RCON: RESET CONTROL REGISTER R/W-0 R/W-1(1) U-0 R/W-1 R-1 R-1 R/W-0(2) R/W-0 IPEN SBOREN -- RI TO PD POR BOR bit 7 bit 0 bit 7 IPEN: Interrupt Priority Enable bit 1 = Enable priority levels on interrupts 0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode) bit 6 SBOREN: BOR Software Enable bit(1) If BOREN1:BOREN0 = 01: 1 = BOR is enabled 0 = BOR is disabled If BOREN1:BOREN0 = 00, 10 or 11: Bit is disabled and read as `0'. bit 5 Unimplemented: Read as `0' bit 4 RI: RESET Instruction Flag bit 1 = The RESET instruction was not executed (set by firmware only) 0 = The RESET instruction was executed causing a device Reset (must be set in software after a Brown-out Reset occurs) bit 3 TO: Watchdog Time-out Flag bit 1 = Set by power-up, CLRWDT instruction or SLEEP instruction 0 = A WDT time-out occurred bit 2 PD: Power-down Detection Flag bit 1 = Set by power-up or by the CLRWDT instruction 0 = Set by execution of the SLEEP instruction bit 1 POR: Power-on Reset Status bit(2) 1 = A Power-on Reset has not occurred (set by firmware only) 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0 BOR: Brown-out Reset Status bit 1 = A Brown-out Reset has not occurred (set by firmware only) 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) Note 1: The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". 2: The actual Reset value of POR is determined by the type of device Reset. See the notes following this register and Section 4.6 "Reset State of Registers" for additional information. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent Power-on Resets may be detected. 2: Brown-out Reset is said to have occurred when BOR is `0' and POR is `1' (assuming that POR was set to `1' by software immediately after POR). DS39636D-page 44 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 4.2 Master Clear (MCLR) The MCLR pin provides a method for triggering an external Reset of the device. A Reset is generated by holding the pin low. These devices have a noise filter in the MCLR Reset path which detects and ignores small pulses. FIGURE 4-2: In PIC18F2X1X/4X1X devices, the MCLR input can be disabled with the MCLRE Configuration bit. When MCLR is disabled, the pin becomes a digital input. See Section 9.5 "PORTE, TRISE and LATE Registers" for more information. 4.3 D To take advantage of the POR circuitry, tie the MCLR pin through a resistor (1 k to 10 k) to VDD. This will eliminate external RC components usually needed to create a Power-on Reset delay. A minimum rise rate for VDD is specified (parameter D004). For a slow rise time, see Figure 4-2. R R1 C MCLR PIC18FXXXX Note 1: External Power-on Reset circuit is required only if the VDD power-up slope is too slow. The diode D helps discharge the capacitor quickly when VDD powers down. 2: R < 40 k is recommended to make sure that the voltage drop across R does not violate the device's electrical specification. 3: R1 1 k will limit any current flowing into MCLR from external capacitor C, in the event of MCLR/VPP pin breakdown, due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). Power-on Reset (POR) A Power-on Reset pulse is generated on-chip whenever VDD rises above a certain threshold. This allows the device to start in the initialized state when VDD is adequate for operation. VDD VDD The MCLR pin is not driven low by any internal Resets, including the WDT. EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP) When the device starts normal operation (i.e., exits the Reset condition), device operating parameters (voltage, frequency, temperature, etc.) must be met to ensure operation. If these conditions are not met, the device must be held in Reset until the operating conditions are met. POR events are captured by the POR bit (RCON<1>). The state of the bit is set to `0' whenever a POR occurs; it does not change for any other Reset event. POR is not reset to `1' by any hardware event. To capture multiple events, the user manually resets the bit to `1' in software following any POR. (c) 2009 Microchip Technology Inc. DS39636D-page 45 PIC18F2X1X/4X1X 4.4 Brown-out Reset (BOR) PIC18F2X1X/4X1X devices implement a BOR circuit that provides the user with a number of configuration and power-saving options. The BOR is controlled by the BORV1:BORV0 and BOREN1:BOREN0 Configuration bits. There are a total of four BOR configurations which are summarized in Table 4-1. The BOR threshold is set by the BORV1:BORV0 bits. If BOR is enabled (any values of BOREN1:BOREN0, except `00'), any drop of VDD below VBOR (parameter D005) for greater than TBOR (parameter 35) will reset the device. A Reset may or may not occur if VDD falls below VBOR for less than TBOR. The chip will remain in Brown-out Reset until VDD rises above VBOR. If the Power-up Timer is enabled, it will be invoked after VDD rises above VBOR; it then will keep the chip in Reset for an additional time delay, TPWRT (parameter 33). If VDD drops below VBOR while the Power-up Timer is running, the chip will go back into a Brown-out Reset and the Power-up Timer will be initialized. Once VDD rises above VBOR, the Power-up Timer will execute the additional time delay. BOR and the Power-on Timer (PWRT) are independently configured. Enabling BOR Reset does not automatically enable the PWRT. 4.4.1 SOFTWARE ENABLED BOR When BOREN1:BOREN0 = 01, the BOR can be enabled or disabled by the user in software. This is done with the control bit, SBOREN (RCON<6>). Setting SBOREN enables the BOR to function as previously described. Clearing SBOREN disables the BOR entirely. The SBOREN bit operates only in this mode; otherwise it is read as `0'. TABLE 4-1: Placing the BOR under software control gives the user the additional flexibility of tailoring the application to its environment without having to reprogram the device to change BOR configuration. It also allows the user to tailor device power consumption in software by eliminating the incremental current that the BOR consumes. While the BOR current is typically very small, it may have some impact in low-power applications. Note: 4.4.2 Even when BOR is under software control, the BOR Reset voltage level is still set by the BORV1:BORV0 Configuration bits. It cannot be changed in software. DETECTING BOR When BOR is enabled, the BOR bit always resets to `0' on any BOR or POR event. This makes it difficult to determine if a BOR event has occurred just by reading the state of BOR alone. A more reliable method is to simultaneously check the state of both POR and BOR. This assumes that the POR bit is reset to `1' in software immediately after any POR event. If BOR is `0' while POR is `1', it can be reliably assumed that a BOR event has occurred. 4.4.3 DISABLING BOR IN SLEEP MODE When BOREN1:BOREN0 = 10, the BOR remains under hardware control and operates as previously described. Whenever the device enters Sleep mode, however, the BOR is automatically disabled. When the device returns to any other operating mode, BOR is automatically re-enabled. This mode allows for applications to recover from brown-out situations, while actively executing code, when the device requires BOR protection the most. At the same time, it saves additional power in Sleep mode by eliminating the small incremental BOR current. BOR CONFIGURATIONS BOR Configuration BOREN1 BOREN0 Status of SBOREN (RCON<6>) 0 0 Unavailable 0 1 Available 1 0 Unavailable BOR enabled in hardware in Run and Idle modes, disabled during Sleep mode. 1 1 Unavailable BOR enabled in hardware; must be disabled by reprogramming the Configuration bits. DS39636D-page 46 BOR Operation BOR disabled; must be enabled by reprogramming the Configuration bits. BOR enabled in software; operation controlled by SBOREN. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 4.5 Device Reset Timers 4.5.3 PIC18F2X1X/4X1X devices incorporate three separate on-chip timers that help regulate the Power-on Reset process. Their main function is to ensure that the device clock is stable before code is executed. These timers are: * Power-up Timer (PWRT) * Oscillator Start-up Timer (OST) * PLL Lock Time-out 4.5.1 With the PLL enabled in its PLL mode, the time-out sequence following a Power-on Reset is slightly different from other oscillator modes. A separate timer is used to provide a fixed time-out that is sufficient for the PLL to lock to the main oscillator frequency. This PLL lock time-out (TPLL) is typically 2 ms and follows the oscillator start-up time-out. 4.5.4 POWER-UP TIMER (PWRT) The Power-up Timer (PWRT) of PIC18F2X1X/4X1X devices is an 11-bit counter which uses the INTRC source as the clock input. This yields an approximate time interval of 2048 x 32 s = 65.6 ms. While the PWRT is counting, the device is held in Reset. The power-up time delay depends on the INTRC clock and will vary from chip to chip due to temperature and process variation. See DC parameter 33 for details. The PWRT is enabled by clearing the PWRTEN Configuration bit. 4.5.2 PLL LOCK TIME-OUT OSCILLATOR START-UP TIMER (OST) The Oscillator Start-up Timer (OST) provides a 1024 oscillator cycle (from OSC1 input) delay after the PWRT delay is over (parameter 33). This ensures that the crystal oscillator or resonator has started and stabilized. TIME-OUT SEQUENCE On power-up, the time-out sequence is as follows: 1. 2. After the POR pulse has cleared, PWRT time-out is invoked (if enabled). Then, the OST is activated. The total time-out will vary based on oscillator configuration and the status of the PWRT. Figure 4-3, Figure 4-4, Figure 4-5, Figure 4-6 and Figure 4-7 all depict time-out sequences on power-up, with the Power-up Timer enabled and the device operating in HS Oscillator mode. Figures 4-3 through 4-6 also apply to devices operating in XT or LP modes. For devices in RC mode and with the PWRT disabled, there will be no time-out at all. Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, all time-outs will expire. Bringing MCLR high will begin execution immediately (Figure 4-5). This is useful for testing purposes or to synchronize more than one PIC18FXXXX device operating in parallel. The OST time-out is invoked only for XT, LP, HS and HSPLL modes and only on Power-on Reset, or on exit from most power-managed modes. TABLE 4-2: TIME-OUT IN VARIOUS SITUATIONS Power-up(2) and Brown-out Oscillator Configuration HSPLL PWRTEN = 0 PWRTEN = 1 Exit From Power-Managed Mode 66 ms(1) + 1024 TOSC + 2 ms(2) 1024 TOSC + 2 ms(2) 1024 TOSC + 2 ms(2) HS, XT, LP 1024 TOSC 1024 TOSC EC, ECIO 66 ms(1) -- -- RC, RCIO 66 ms(1) -- -- ms(1) -- -- INTIO1, INTIO2 66 ms(1) + 1024 TOSC 66 Note 1: 66 ms (65.5 ms) is the nominal Power-up Timer (PWRT) delay. 2: 2 ms is the nominal time required for the PLL to lock. (c) 2009 Microchip Technology Inc. DS39636D-page 47 PIC18F2X1X/4X1X FIGURE 4-3: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD, VDD RISE < TPWRT) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 FIGURE 4-4: VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 FIGURE 4-5: VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET DS39636D-page 48 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 4-6: SLOW RISE TIME (MCLR TIED TO VDD, VDD RISE > TPWRT) 5V VDD 0V MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 4-7: TIME-OUT SEQUENCE ON POR W/PLL ENABLED (MCLR TIED TO VDD) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT OST TIME-OUT TOST TPLL PLL TIME-OUT INTERNAL RESET Note: TOST = 1024 clock cycles. TPLL 2 ms max. First three stages of the PWRT timer. (c) 2009 Microchip Technology Inc. DS39636D-page 49 PIC18F2X1X/4X1X 4.6 Reset State of Registers Most registers are unaffected by a Reset. Their status is unknown on POR and unchanged by all other Resets. The other registers are forced to a "Reset state" depending on the type of Reset that occurred. Table 4-4 describes the Reset states for all of the Special Function Registers. These are categorized by Power-on and Brown-out Resets, Master Clear and WDT Resets and WDT wake-ups. Most registers are not affected by a WDT wake-up, since this is viewed as the resumption of normal operation. Status bits from the RCON register, RI, TO, PD, POR and BOR, are set or cleared differently in different Reset situations, as indicated in Table 4-3. These bits are used in software to determine the nature of the Reset. TABLE 4-3: STATUS BITS, THEIR SIGNIFICANCE AND THE INITIALIZATION CONDITION FOR RCON REGISTER RCON Register STKPTR Register Program Counter SBOREN RI TO PD 0000h 1 1 1 1 0 0 0 0 RESET instruction 0000h u(2) 0 u u u u u u Brown-out Reset 0000h u(2) 1 1 1 u 0 u u MCLR during power-managed Run modes 0000h u(2) u 1 u u u u u MCLR during power-managed Idle modes and Sleep mode 0000h u(2) u 1 0 u u u u WDT time-out during full power or power-managed Run mode 0000h u(2) u 0 u u u u u MCLR during full power execution 0000h u(2) u u u u u u u Stack Full Reset (STVREN = 1) 0000h u(2) u u u u u 1 u Stack Underflow Reset (STVREN = 1) 0000h (2) u u u u u u u 1 Stack Underflow Error (not an actual Reset, STVREN = 0) 0000h u(2) u u u u u u 1 WDT Time-out during power-managed Idle or Sleep modes PC + 2 u(2) u 0 0 u u u u PC + 2(1) u(2) u u 0 u u u u Condition Power-on Reset Interrupt exit from power-managed modes POR BOR STKFUL STKUNF Legend: u = unchanged Note 1: When the wake-up is due to an interrupt and the GIEH or GIEL bits are set, the PC is loaded with the interrupt vector (008h or 0018h). 2: Reset state is `1' for POR and unchanged for all other Resets when software BOR is enabled (BOREN1:BOREN0 Configuration bits = 01 and SBOREN = 1); otherwise, the Reset state is `0'. DS39636D-page 50 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 4-4: INITIALIZATION CONDITIONS FOR ALL REGISTERS Register Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt TOSU 2410 2510 2515 2610 4410 4510 4515 4610 ---0 0000 ---0 0000 ---0 uuuu(3) TOSH 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu(3) TOSL 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu(3) STKPTR 2410 2510 2515 2610 4410 4510 4515 4610 00-0 0000 uu-0 0000 uu-u uuuu(3) PCLATU 2410 2510 2515 2610 4410 4510 4515 4610 ---0 0000 ---0 0000 ---u uuuu PCLATH 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu PCL 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 PC + 2(2) TBLPTRU 2410 2510 2515 2610 4410 4510 4515 4610 --00 0000 --00 0000 --uu uuuu TBLPTRH 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu TBLPTRL 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu TABLAT 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu PRODH 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu PRODL 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu INTCON 2410 2510 2515 2610 4410 4510 4515 4610 0000 000x 0000 000u uuuu uuuu(1) INTCON2 2410 2510 2515 2610 4410 4510 4515 4610 1111 -1-1 1111 -1-1 uuuu -u-u(1) INTCON3 2410 2510 2515 2610 4410 4510 4515 4610 11-0 0-00 11-0 0-00 uu-u u-uu(1) INDF0 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A POSTINC0 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A POSTDEC0 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A PREINC0 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A PLUSW0 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A FSR0H 2410 2510 2515 2610 4410 4510 4515 4610 ---- 0000 ---- 0000 ---- uuuu FSR0L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu WREG 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu INDF1 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A POSTINC1 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A POSTDEC1 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A PREINC1 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A PLUSW1 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A Legend: Note 1: 2: 3: 4: 5: u = unchanged, x = unknown, - = unimplemented bit, read as `0', q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. See Table 4-3 for Reset value for specific condition. Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 51 PIC18F2X1X/4X1X TABLE 4-4: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt FSR1H 2410 2510 2515 2610 4410 4510 4515 4610 ---- 0000 ---- 0000 ---- uuuu FSR1L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu BSR 2410 2510 2515 2610 4410 4510 4515 4610 ---- 0000 ---- 0000 ---- uuuu INDF2 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A POSTINC2 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A POSTDEC2 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A PREINC2 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A PLUSW2 2410 2510 2515 2610 4410 4510 4515 4610 N/A N/A N/A FSR2H 2410 2510 2515 2610 4410 4510 4515 4610 ---- 0000 ---- 0000 ---- uuuu FSR2L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu STATUS 2410 2510 2515 2610 4410 4510 4515 4610 ---x xxxx ---u uuuu ---u uuuu TMR0H 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu TMR0L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu T0CON 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111 1111 1111 uuuu uuuu OSCCON 2410 2510 2515 2610 4410 4510 4515 4610 0100 q000 0100 q000 uuuu uuqu u-uu uuuu HLVDCON 2410 2510 2515 2610 4410 4510 4515 4610 0-00 0101 0-00 0101 WDTCON 2410 2510 2515 2610 4410 4510 4515 4610 ---- ---0 ---- ---0 ---- ---u RCON(4) 2410 2510 2515 2610 4410 4510 4515 4610 0q-1 11q0 0q-q qquu uq-u qquu TMR1H 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu TMR1L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu T1CON 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 u0uu uuuu uuuu uuuu TMR2 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu PR2 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111 1111 1111 1111 1111 T2CON 2410 2510 2515 2610 4410 4510 4515 4610 -000 0000 -000 0000 -uuu uuuu SSPBUF 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu SSPADD 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu SSPSTAT 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu SSPCON1 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu SSPCON2 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu Legend: Note 1: 2: 3: 4: 5: u = unchanged, x = unknown, - = unimplemented bit, read as `0', q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. See Table 4-3 for Reset value for specific condition. Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read `0'. DS39636D-page 52 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 4-4: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt ADRESH 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu ADRESL 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu ADCON0 2410 2510 2515 2610 4410 4510 4515 4610 --00 0000 --00 0000 --uu uuuu ADCON1 2410 2510 2515 2610 4410 4510 4515 4610 --00 0qqq --00 0qqq --uu uuuu ADCON2 2410 2510 2515 2610 4410 4510 4515 4610 0-00 0000 0-00 0000 u-uu uuuu CCPR1H 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu CCPR1L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu CCP1CON 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu 2410 2510 2515 2610 4410 4510 4515 4610 --00 0000 --00 0000 --uu uuuu CCPR2H 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu CCPR2L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu CCP2CON 2410 2510 2515 2610 4410 4510 4515 4610 --00 0000 --00 0000 --uu uuuu BAUDCON 2410 2510 2515 2610 4410 4510 4515 4610 01-0 0-00 01-0 0-00 --uu uuuu PWM1CON 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu ECCP1AS 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu 2410 2510 2515 2610 4410 4510 4515 4610 0000 00-- 0000 00-- uuuu uu-- CVRCON 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu CMCON 2410 2510 2515 2610 4410 4510 4515 4610 0000 0111 0000 0111 uuuu uuuu TMR3H 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu TMR3L 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu T3CON 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 uuuu uuuu uuuu uuuu SPBRGH 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu SPBRG 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu RCREG 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu TXREG 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu TXSTA 2410 2510 2515 2610 4410 4510 4515 4610 0000 0010 0000 0010 uuuu uuuu RCSTA 2410 2510 2515 2610 4410 4510 4515 4610 0000 000x 0000 000x uuuu uuuu Legend: Note 1: 2: 3: 4: 5: u = unchanged, x = unknown, - = unimplemented bit, read as `0', q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. See Table 4-3 for Reset value for specific condition. Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 53 PIC18F2X1X/4X1X TABLE 4-4: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Applicable Devices Power-on Reset, Brown-out Reset MCLR Resets, WDT Reset, RESET Instruction, Stack Resets Wake-up via WDT or Interrupt IPR2 2410 2510 2515 2610 4410 4510 4515 4610 11-- 1111 11-- 1111 uu-- uuuu PIR2 2410 2510 2515 2610 4410 4510 4515 4610 00-- 0000 00-- 0000 uu-- uuuu(1) PIE2 2410 2510 2515 2610 4410 4510 4515 4610 00-- 0000 00-- 0000 uu-- uuuu uuuu uuuu IPR1 PIR1 PIE1 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111 1111 1111 2410 2510 2515 2610 4410 4510 4515 4610 -111 1111 -111 1111 -uuu uuuu 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu(1) 2410 2510 2515 2610 4410 4510 4515 4610 -000 0000 -000 0000 -uuu uuuu(1) 2410 2510 2515 2610 4410 4510 4515 4610 0000 0000 0000 0000 uuuu uuuu 2410 2510 2515 2610 4410 4510 4515 4610 -000 0000 -000 0000 -uuu uuuu OSCTUNE 2410 2510 2515 2610 4410 4510 4515 4610 00-0 0000 00-0 0000 uu-u uuuu TRISE 2410 2510 2515 2610 4410 4510 4515 4610 0000 -111 0000 -111 uuuu -uuu TRISD 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111 1111 1111 uuuu uuuu TRISC 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111 1111 1111 uuuu uuuu TRISB 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111 1111 1111 uuuu uuuu TRISA(5) 2410 2510 2515 2610 4410 4510 4515 4610 1111 1111(5) 1111 1111(5) uuuu uuuu(5) LATE 2410 2510 2515 2610 4410 4510 4515 4610 ---- -xxx ---- -uuu ---- -uuu LATD 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu LATC 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu LATB 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu LATA (5) 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx (5) uuuu uuuu uuuu uuuu (5) uuuu uuuu(5) PORTE 2410 2510 2515 2610 4410 4510 4515 4610 ---- x000 ---- x000 ---- uuuu PORTD 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu PORTC 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu PORTB 2410 2510 2515 2610 4410 4510 4515 4610 xxxx xxxx uuuu uuuu uuuu uuuu PORTA(5) 2410 2510 2515 2610 4410 4510 4515 4610 xx0x 0000(5) uu0u 0000(5) uuuu uuuu(5) Legend: Note 1: 2: 3: 4: 5: u = unchanged, x = unknown, - = unimplemented bit, read as `0', q = value depends on condition. Shaded cells indicate conditions do not apply for the designated device. One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt vector (0008h or 0018h). When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are updated with the current value of the PC. The STKPTR is modified to point to the next location in the hardware stack. See Table 4-3 for Reset value for specific condition. Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the oscillator mode selected. When not enabled as PORTA pins, they are disabled and read `0'. DS39636D-page 54 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 5.0 MEMORY ORGANIZATION 5.1 Program Memory Organization PIC18 microcontrollers implement a 21-bit program counter, which is capable of addressing a 2-Mbyte program memory space. Accessing a location between the upper boundary of the physically implemented memory and the 2-Mbyte address will return all `0's (a NOP instruction). There are two types of memory in PIC18F2X1X/4X1X microcontroller devices: * Program Memory * Data RAM As Harvard architecture devices, the data and program memories use separate busses; this allows for concurrent access of the two memory spaces. The PIC18F2410/4410 and PIC18F2510 each have 16 Kbytes of Flash memory and can store up to 8,192 single-word instructions. The PIC18F2510/4510 each have 32 Kbytes of Flash memory and can store up to 16,384 single-word instructions. The PIC18F2515/4515 each have 48 Kbytes of Flash memory and can store up to 24,576 single-word instructions. The PIC18F2610/ 4610 each have 64 Kbytes of Flash memory and can store up to 32,768 single-word instructions. Additional detailed information on the operation of the Flash program memory is provided in Section 6.0 "Flash Program Memory". PIC18 devices have two interrupt vectors. The Reset vector address is at 0000h and the interrupt vector addresses are at 0008h and 0018h. The program memory map for PIC18F2X1X/4X1X devices is shown in Figure 5-1. FIGURE 5-1: PROGRAM MEMORY MAP AND STACK FOR PIC18F2X1X/4X1X DEVICES PC<20:0> CALL,RCALL,RETURN RETFIE,RETLW Stack Level 1 21 * * * Stack Level 31 On-Chip Program Memory (16 Kbytes) Reset Vector 00000h High Priority Interrupt Vector 00008h Low Priority Interrupt Vector 00018h On-Chip Program Memory (32 Kbytes) On-Chip Program Memory (48 Kbytes) On-Chip Program Memory (64 Kbytes) User Memory Space 03FFFh 04000h 07FFFh 08000h 0BFFFh 0C000h 0FFFFh 10000h Read `0' Read `0' Read `0' Read `0' PIC18F2410/4410 PIC18F2510/4510 PIC18F2515/4515 PIC18F2610/4610 (c) 2009 Microchip Technology Inc. 1FFFFFh 200000h DS39636D-page 55 PIC18F2X1X/4X1X 5.1.1 PROGRAM COUNTER The Program Counter (PC) specifies the address of the instruction to fetch for execution. The PC is 21 bits wide and is contained in three separate 8-bit registers. The low byte, known as the PCL register, is both readable and writable. The high byte, or PCH register, contains the PC<15:8> bits; it is not directly readable or writable. Updates to the PCH register are performed through the PCLATH register. The upper byte is called PCU. This register contains the PC<20:16> bits; it is also not directly readable or writable. Updates to the PCU register are performed through the PCLATU register. The contents of PCLATH and PCLATU are transferred to the program counter by any operation that writes PCL. Similarly, the upper two bytes of the program counter are transferred to PCLATH and PCLATU by an operation that reads PCL. This is useful for computed offsets to the PC (see Section 5.1.4.1 "Computed GOTO"). The PC addresses bytes in the program memory. To prevent the PC from becoming misaligned with word instructions, the Least Significant bit of PCL is fixed to a value of `0'. The PC increments by 2 to address sequential instructions in the program memory. The CALL, RCALL, GOTO and program branch instructions write to the program counter directly. For these instructions, the contents of PCLATH and PCLATU are not transferred to the program counter. 5.1.2 RETURN ADDRESS STACK The return address stack allows any combination of up to 31 program calls and interrupts to occur. The PC is pushed onto the stack when a CALL or RCALL instruction is executed or an interrupt is Acknowledged. The PC value is pulled off the stack on a RETURN, RETLW or a RETFIE instruction. PCLATU and PCLATH are not affected by any of the RETURN or CALL instructions. FIGURE 5-2: The stack operates as a 31-word by 21-bit RAM and a 5-bit Stack Pointer, STKPTR. The stack space is not part of either program or data space. The Stack Pointer is readable and writable and the address on the top of the stack is readable and writable through the top-ofstack Special File Registers. Data can also be pushed to, or popped from the stack, using these registers. A CALL type instruction causes a push onto the stack; the Stack Pointer is first incremented and the location pointed to by the Stack Pointer is written with the contents of the PC (already pointing to the instruction following the CALL). A RETURN type instruction causes a pop from the stack; the contents of the location pointed to by the STKPTR are transferred to the PC and then the Stack Pointer is decremented. The Stack Pointer is initialized to `00000' after all Resets. There is no RAM associated with the location corresponding to a Stack Pointer value of `00000'; this is only a Reset value. Status bits indicate if the stack is full or has overflowed or has underflowed. 5.1.2.1 Top-of-Stack Access Only the top of the return address stack (TOS) is readable and writable. A set of three registers, TOSU:TOSH:TOSL, hold the contents of the stack location pointed to by the STKPTR register (Figure 5-2). This allows users to implement a software stack if necessary. After a CALL, RCALL or interrupt, the software can read the pushed value by reading the TOSU:TOSH:TOSL registers. These values can be placed on a user defined software stack. At return time, the software can return these values to TOSU:TOSH:TOSL and do a return. The user must disable the global interrupt enable bits while accessing the stack to prevent inadvertent stack corruption. RETURN ADDRESS STACK AND ASSOCIATED REGISTERS Return Address Stack <20:0> 11111 11110 11101 Top-of-Stack Registers TOSU 00h TOSH 1Ah DS39636D-page 56 STKPTR<4:0> 00010 TOSL 34h Top-of-Stack Stack Pointer 001A34h 000D58h 00011 00010 00001 00000 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 5.1.2.2 Return Stack Pointer (STKPTR) When the stack has been popped enough times to unload the stack, the next pop will return a value of zero to the PC and sets the STKUNF bit, while the Stack Pointer remains at zero. The STKUNF bit will remain set until cleared by software or until a POR occurs. The STKPTR register (Register 5-1) contains the Stack Pointer value, the STKFUL (Stack Full) status bit and the STKUNF (Stack Underflow) status bits. The value of the Stack Pointer can be 0 through 31. The Stack Pointer increments before values are pushed onto the stack and decrements after values are popped off the stack. On Reset, the Stack Pointer value will be zero. The user may read and write the Stack Pointer value. This feature can be used by a Real-Time Operating System (RTOS) for return stack maintenance. Note: After the PC is pushed onto the stack 31 times (without popping any values off the stack), the STKFUL bit is set. The STKFUL bit is cleared by software or by a POR. 5.1.2.3 PUSH and POP Instructions Since the Top-of-Stack is readable and writable, the ability to push values onto the stack and pull values off the stack without disturbing normal program execution is a desirable feature. The PIC18 instruction set includes two instructions, PUSH and POP, that permit the TOS to be manipulated under software control. TOSU, TOSH and TOSL can be modified to place data or a return address on the stack. The action that takes place when the stack becomes full depends on the state of the STVREN (Stack Overflow Reset Enable) Configuration bit. (Refer to Section 22.1 "Configuration Bits" for a description of the device Configuration bits.) If STVREN is set (default), the 31st push will push the (PC + 2) value onto the stack, set the STKFUL bit and reset the device. The STKFUL bit will remain set and the Stack Pointer will be set to zero. The PUSH instruction places the current PC value onto the stack. This increments the Stack Pointer and loads the current PC value onto the stack. If STVREN is cleared, the STKFUL bit will be set on the 31st push and the Stack Pointer will increment to 31. Any additional pushes will not overwrite the 31st push and STKPTR will remain at 31. REGISTER 5-1: Returning a value of zero to the PC on an underflow has the effect of vectoring the program to the Reset vector, where the stack conditions can be verified and appropriate actions can be taken. This is not the same as a Reset, as the contents of the SFRs are not affected. The POP instruction discards the current TOS by decrementing the Stack Pointer. The previous value pushed onto the stack then becomes the TOS value. STKPTR: STACK POINTER REGISTER R/C-0 R/C-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 STKFUL(1) STKUNF(1) -- SP4 SP3 SP2 SP1 SP0 bit 7 bit 0 bit 7 STKFUL: Stack Full Flag bit(1) 1 = Stack became full or overflowed 0 = Stack has not become full or overflowed bit 6 STKUNF: Stack Underflow Flag bit(1) 1 = Stack underflow occurred 0 = Stack underflow did not occur bit 5 Unimplemented: Read as `0' bit 4-0 SP4:SP0: Stack Pointer Location bits Note 1: Bit 7 and bit 6 are cleared by user software or by a POR. Legend: R = Readable bit W = Writable bit U = Unimplemented C = Clearable only bit -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. DS39636D-page 57 PIC18F2X1X/4X1X 5.1.2.4 Stack Full and Underflow Resets Device Resets on stack overflow and stack underflow conditions are enabled by setting the STVREN bit in Configuration Register 4L. When STVREN is set, a full or underflow will set the appropriate STKFUL or STKUNF bit and then cause a device Reset. When STVREN is cleared, a full or underflow condition will set the appropriate STKFUL or STKUNF bit but not cause a device Reset. The STKFUL or STKUNF bits are cleared by the user software or a Power-on Reset. 5.1.3 FAST REGISTER STACK A fast register stack is provided for the STATUS, WREG and BSR registers, to provide a "fast return" option for interrupts. The stack for each register is only one level deep and is neither readable nor writable. It is loaded with the current value of the corresponding register when the processor vectors for an interrupt. All interrupt sources will push values into the stack registers. The values in the registers are then loaded back into their associated registers if the RETFIE, FAST instruction is used to return from the interrupt. 5.1.4 LOOK-UP TABLES IN PROGRAM MEMORY There may be programming situations that require the creation of data structures, or look-up tables, in program memory. For PIC18 devices, look-up tables can be implemented in two ways: * Computed GOTO * Table Reads 5.1.4.1 Computed GOTO A computed GOTO is accomplished by adding an offset to the program counter. An example is shown in Example 5-2. A look-up table can be formed with an ADDWF PCL instruction and a group of RETLW nn instructions. The W register is loaded with an offset into the table before executing a call to that table. The first instruction of the called routine is the ADDWF PCL instruction. The next instruction executed will be one of the RETLW nn instructions that returns the value `nn' to the calling function. If both low and high priority interrupts are enabled, the stack registers cannot be used reliably to return from low priority interrupts. If a high priority interrupt occurs while servicing a low priority interrupt, the stack register values stored by the low priority interrupt will be overwritten. In these cases, users must save the key registers in software during a low priority interrupt. The offset value (in WREG) specifies the number of bytes that the program counter should advance and should be multiples of 2 (LSb = 0). If interrupt priority is not used, all interrupts may use the fast register stack for returns from interrupt. If no interrupts are used, the fast register stack can be used to restore the STATUS, WREG and BSR registers at the end of a subroutine call. To use the fast register stack for a subroutine call, a CALL label, FAST instruction must be executed to save the STATUS, WREG and BSR registers to the fast register stack. A RETURN, FAST instruction is then executed to restore these registers from the fast register stack. EXAMPLE 5-2: Example 5-1 shows a source code example that uses the fast register stack during a subroutine call and return. EXAMPLE 5-1: CALL SUB1, FAST * * * * RETURN, FAST FAST REGISTER STACK CODE EXAMPLE ;STATUS, WREG, BSR ;SAVED IN FAST REGISTER ;STACK SUB1 DS39636D-page 58 ;RESTORE VALUES SAVED ;IN FAST REGISTER STACK In this method, only one data byte may be stored in each instruction location and room on the return address stack is required. ORG TABLE 5.1.4.2 MOVF CALL nn00h ADDWF RETLW RETLW RETLW . . . COMPUTED GOTO USING AN OFFSET VALUE OFFSET, W TABLE PCL nnh nnh nnh Table Reads and Table Writes A better method of storing data in program memory allows two bytes of data to be stored in each instruction location. Look-up table data may be stored two bytes per program word by using table reads and writes. The Table Pointer (TBLPTR) register specifies the byte address and the Table Latch (TABLAT) register contains the data that is read from or written to program memory. Data is transferred to or from program memory one byte at a time. Table read and table write operations are discussed further in Section 6.1 "Table Reads". (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 5.2 PIC18 Instruction Cycle 5.2.1 5.2.2 An "Instruction Cycle" consists of four Q cycles: Q1 through Q4. The instruction fetch and execute are pipelined in such a manner that a fetch takes one instruction cycle, while the decode and execute take another instruction cycle. However, due to the pipelining, each instruction effectively executes in one cycle. If an instruction causes the program counter to change (e.g., GOTO), then two cycles are required to complete the instruction (Example 5-3). CLOCKING SCHEME The microcontroller clock input, whether from an internal or external source, is internally divided by four to generate four non-overlapping quadrature clocks (Q1, Q2, Q3 and Q4). Internally, the program counter is incremented on every Q1; the instruction is fetched from the program memory and latched into the instruction register during Q4. The instruction is decoded and executed during the following Q1 through Q4. The clocks and instruction execution flow are shown in Figure 5-3. FIGURE 5-3: INSTRUCTION FLOW/PIPELINING A fetch cycle begins with the Program Counter (PC) incrementing in Q1. In the execution cycle, the fetched instruction is latched into the Instruction Register (IR) in cycle Q1. This instruction is then decoded and executed during the Q2, Q3 and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write). CLOCK/INSTRUCTION CYCLE Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q2 Q1 Q3 Q4 OSC1 Q1 Q2 Internal Phase Clock Q3 Q4 PC PC PC + 2 PC + 4 OSC2/CLKO (RC mode) Execute INST (PC - 2) Fetch INST (PC) EXAMPLE 5-3: TCY0 TCY1 Fetch 1 Execute 1 2. MOVWF PORTB 4. BSF Execute INST (PC + 2) Fetch INST (PC + 4) INSTRUCTION PIPELINE FLOW 1. MOVLW 55h 3. BRA Execute INST (PC) Fetch INST (PC + 2) SUB_1 PORTA, BIT3 (Forced NOP) 5. Instruction @ address SUB_1 Fetch 2 TCY2 TCY3 TCY4 TCY5 Execute 2 Fetch 3 Execute 3 Fetch 4 Flush (NOP) Fetch SUB_1 Execute SUB_1 All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction is "flushed" from the pipeline while the new instruction is being fetched and then executed. (c) 2009 Microchip Technology Inc. DS39636D-page 59 PIC18F2X1X/4X1X 5.2.3 INSTRUCTIONS IN PROGRAM MEMORY The program memory is addressed in bytes. Instructions are stored as two bytes or four bytes in program memory. The Least Significant Byte of an instruction word is always stored in a program memory location with an even address (LSb = 0). To maintain alignment with instruction boundaries, the PC increments in steps of 2 and the LSb will always read `0' (see Section 5.1.1 "Program Counter"). Figure 5-4 shows an example of how instruction words are stored in the program memory. FIGURE 5-4: INSTRUCTIONS IN PROGRAM MEMORY Program Memory Byte Locations 5.2.4 The CALL and GOTO instructions have the absolute program memory address embedded into the instruction. Since instructions are always stored on word boundaries, the data contained in the instruction is a word address. The word address is written to PC<20:1>, which accesses the desired byte address in program memory. Instruction #2 in Figure 5-4 shows how the instruction GOTO 0006h is encoded in the program memory. Program branch instructions, which encode a relative address offset, operate in the same manner. The offset value stored in a branch instruction represents the number of single-word instructions that the PC will be offset by. Section 23.0 "Instruction Set Summary" provides further details of the instruction set. Instruction 1: Instruction 2: MOVLW GOTO 055h 0006h Instruction 3: MOVFF 123h, 456h TWO-WORD INSTRUCTIONS The standard PIC18 instruction set has four two-word instructions: CALL, MOVFF, GOTO and LSFR. In all cases, the second word of the instructions always has `1111' as its four Most Significant bits; the other 12 bits are literal data, usually a data memory address. The use of `1111' in the 4 MSbs of an instruction specifies a special form of NOP. If the instruction is executed in proper sequence - immediately after the first word - the data in the second word is accessed and used by the instruction sequence. If the first word is skipped for EXAMPLE 5-4: CASE 1: Object Code 0110 0110 0000 1100 0001 0010 1111 0100 0101 0010 0100 0000 CASE 2: Object Code 0110 0110 0000 1100 0001 0010 1111 0100 0101 0010 0100 0000 DS39636D-page 60 LSB = 1 LSB = 0 0Fh EFh F0h C1h F4h 55h 03h 00h 23h 56h Word Address 000000h 000002h 000004h 000006h 000008h 00000Ah 00000Ch 00000Eh 000010h 000012h 000014h some reason and the second word is executed by itself, a NOP is executed instead. This is necessary for cases when the two-word instruction is preceded by a conditional instruction that changes the PC. Example 5-4 shows how this works. Note: See Section 5.6 "PIC18 Instruction Execution and the Extended Instruction Set" for information on two-word instructions in the extended instruction set. TWO-WORD INSTRUCTIONS 0000 0011 0110 0000 Source Code TSTFSZ REG1 ; is RAM location 0? MOVFF REG1, REG2 ; No, skip this word ; Execute this word as a NOP ADDWF REG3 ; continue code 0000 0011 0110 0000 Source Code TSTFSZ REG1 ; is RAM location 0? MOVFF REG1, REG2 ; Yes, execute this word ; 2nd word of instruction ADDWF REG3 ; continue code (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 5.3 Note: Data Memory Organization The operation of some aspects of data memory are changed when the PIC18 extended instruction set is enabled. See Section 5.5 "Data Memory and the Extended Instruction Set" for more information. The data memory in PIC18 devices is implemented as static RAM. Figures 5-5, 5-6 and 5-7 show the data memory organization for the PIC18F2X1X/4X1X devices. The data memory contains Special Function Registers (SFRs) and General Purpose Registers (GPRs). The SFRs are used for control and status of the controller and peripheral functions, while GPRs are used for data storage and scratchpad operations in the user's application. Any read of an unimplemented location will read as `0's. The instruction set and architecture allow operations across all banks. The entire data memory may be accessed by Direct, Indirect or Indexed Addressing modes. Addressing modes are discussed later in this subsection. To ensure that commonly used registers (SFRs and select GPRs) can be accessed in a single cycle, PIC18 devices implement an Access Bank. This is a 256-byte memory space that provides fast access to SFRs and the lower portion of GPR Bank 0 without using the BSR. Section 5.3.2 "Access Bank" provides a detailed description of the Access RAM. 5.3.1 BANK SELECT REGISTER (BSR) Large areas of data memory require an efficient addressing scheme to make rapid access to any address possible. Ideally, this means that an entire address does not need to be provided for each read or write operation. For PIC18 devices, this is accomplished with a RAM banking scheme. This divides the memory space into 16 contiguous banks of 256 bytes. Depending on the instruction, each location can be addressed directly by its full 12-bit address, or an 8-bit low-order address and a 4-bit Bank Pointer. Most instructions in the PIC18 instruction set make use of the Bank Pointer, known as the Bank Select Register (BSR). This SFR holds the 4 Most Significant bits of a location's address; the instruction itself includes the 8 Least Significant bits. Only the four lower bits of the BSR are implemented (BSR3:BSR0). The upper four bits are unused; they will always read `0' and cannot be written to. The BSR can be loaded directly by using the MOVLB instruction. The value of the BSR indicates the bank in data memory; the 8 bits in the instruction show the location in the bank and can be thought of as an offset from the bank's lower boundary. The relationship between the BSR's value and the bank division in data memory is shown in Figure 5-8. Since up to 16 registers may share the same low-order address, the user must always be careful to ensure that the proper bank is selected before performing a data read or write. For example, writing what should be program data to an 8-bit address of F9h, while the BSR is 0Fh, will end up resetting the program counter. While any bank can be selected, only those banks that are actually implemented can be read or written to. Writes to unimplemented banks are ignored, while reads from unimplemented banks will return `0's. Even so, the STATUS register will still be affected as if the operation was successful. The data memory map in Figure 5-5 indicates which banks are implemented. In the core PIC18 instruction set, only the MOVFF instruction fully specifies the 12-bit address of the source and target registers. This instruction ignores the BSR completely when it executes. All other instructions include only the low-order address as an operand and must use either the BSR or the Access Bank to locate their target registers. (c) 2009 Microchip Technology Inc. DS39636D-page 61 PIC18F2X1X/4X1X FIGURE 5-5: DATA MEMORY MAP FOR PIC18F2410/4410 DEVICES BSR<3:0> = 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 1100 = 1101 = 1110 = 1111 DS39636D-page 62 When `a' = 0: Data Memory Map 00h Access RAM FFh 00h GPR Bank 0 GPR Bank 1 Bank 2 Bank 3 Bank 4 Bank 5 Bank 6 Bank 7 Bank 8 Bank 9 000h 07Fh 080h 0FFh 100h 1FFh 200h FFh 00h 2FFh 300h FFh 00h 3FFh 400h FFh 00h 4FFh 500h FFh 00h 5FFh 600h FFh 00h 6FFh 700h 7FFh 800h FFh 00h FFh 00h Unused Read 00h FFh 00h AFFh B00h FFh 00h BFFh C00h FFh Bank 13 00h CFFh D00h FFh 00h DFFh E00h Bank 12 Bank 14 The second 128 bytes are Special Function Registers (from Bank 15). FFh 00h Unused FFh SFR Bank 15 When `a' = 1: The BSR specifies the Bank used by the instruction. Access Bank Access RAM Low 00h 7Fh Access RAM High 80h (SFRs) FFh 8FFh 900h 9FFh A00h Bank 11 The first 128 bytes are general purpose RAM (from Bank 0). GPR FFh 00h FFh 00h Bank 10 The BSR is ignored and the Access Bank is used. EFFh F00h F7Fh F80h FFFh (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 5-6: DATA MEMORY MAP FOR PIC18F2510/4510 DEVICES BSR<3:0> = 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 1100 = 1101 = 1110 = 1111 When `a' = 0: Data Memory Map 00h Access RAM FFh 00h GPR Bank 0 GPR Bank 1 Bank 2 Bank 3 Bank 4 Bank 5 Bank 6 Bank 7 Bank 8 Bank 9 Bank 10 000h 07Fh 080h 0FFh 100h 1FFh 200h FFh 00h 2FFh 300h GPR 3FFh 400h FFh 00h The BSR specifies the Bank used by the instruction. GPR FFh 00h 5FFh 600h FFh 00h 6FFh 700h FFh 00h 7FFh 800h FFh 00h 8FFh 900h FFh 00h Unused Read 00h FFh Bank 13 00h CFFh D00h FFh 00h DFFh E00h FFh 00h Unused FFh SFR Bank 15 Access Bank Access RAM Low 00h 7Fh Access RAM High 80h (SFRs) FFh 9FFh A00h BFFh C00h (c) 2009 Microchip Technology Inc. When `a' = 1: 4FFh 500h FFh 00h Bank 14 The second 128 bytes are Special Function Registers (from Bank 15). GPR FFh 00h AFFh B00h Bank 12 The first 128 bytes are general purpose RAM (from Bank 0). GPR FFh 00h FFh 00h Bank 11 The BSR is ignored and the Access Bank is used. EFFh F00h F7Fh F80h FFFh DS39636D-page 63 PIC18F2X1X/4X1X FIGURE 5-7: DATA MEMORY MAP FOR PIC18F2515/2610/4515/4610 DEVICES BSR<3:0> = 0000 = 0001 = 0010 = 0011 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 1100 = 1101 = 1110 = 1111 DS39636D-page 64 When a = 0: Data Memory Map 00h Access RAM FFh 00h GPR Bank 0 GPR Bank 1 Bank 2 Bank 3 Bank 4 Bank 5 Bank 6 Bank 7 Bank 8 Bank 9 Bank 10 Bank 11 Bank 12 1FFh 200h FFh 00h The BSR is ignored and the Access Bank is used. The first 128 bytes are general purpose RAM (from Bank 0). The second 128 bytes are Special Function Registers (from Bank 15). GPR FFh 00h 2FFh 300h GPR 3FFh 400h FFh 00h When a = 1: The BSR specifies the Bank used by the instruction. GPR 4FFh 500h FFh 00h GPR 5FFh 600h FFh 00h GPR FFh 00h 6FFh 700h GPR 7FFh 800h FFh 00h GPR FFh 00h FFh 00h FFh 00h FFh 00h FFh Bank 13 00h Bank 14 000h 07Fh 080h 0FFh 100h FFh 00h Access RAM Low 00h 7Fh Access RAM High 80h (SFRs) FFh 8FFh 900h GPR 9FFh A00h GPR AFFh B00h GPR BFFh C00h GPR CFFh D00h GPR DFFh E00h GPR FFh 00h GPR FFh SFR Bank 15 Access Bank EFFh F00h F7Fh F80h FFFh (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 5-8: USE OF THE BANK SELECT REGISTER (DIRECT ADDRESSING) BSR(1) 7 0 0 0 0 0 Bank Select(2) 0 0 1 1 000h Data Memory 00h Bank 0 FFh 00h 100h Bank 1 1 1 1 1 1 1 0 1 1 FFh 00h 200h 300h From Opcode(2) 7 Bank 2 FFh 00h Bank 3 through Bank 13 FFh 00h E00h Bank 14 FFh 00h F00h FFFh Note 1: 2: 5.3.2 Bank 15 FFh The Access RAM bit of the instruction can be used to force an override of the selected bank (BSR<3:0>) to the registers of the Access Bank. The MOVFF instruction embeds the entire 12-bit address in the instruction. ACCESS BANK While the use of the BSR with an embedded 8-bit address allows users to address the entire range of data memory, it also means that the user must always ensure that the correct bank is selected. Otherwise, data may be read from or written to the wrong location. This can be disastrous if a GPR is the intended target of an operation, but an SFR is written to instead. Verifying and/or changing the BSR for each read or write to data memory can become very inefficient. To streamline access for the most commonly used data memory locations, the data memory is configured with an Access Bank, which allows users to access a mapped block of memory without specifying a BSR. The Access Bank consists of the first 128 bytes of memory (00h-7Fh) in Bank 0 and the last 128 bytes of memory (80h-FFh) in Block 15. The lower half is known as the "Access RAM" and is composed of GPRs. This upper half is also where the device's SFRs are mapped. These two areas are mapped contiguously in the Access Bank and can be addressed in a linear fashion by an 8-bit address (Figure 5-5). The Access Bank is used by core PIC18 instructions that include the Access RAM bit (the `a' parameter in the instruction). When `a' is equal to `1', the instruction uses the BSR and the 8-bit address included in the opcode for the data memory address. When `a' is `0', however, the instruction is forced to use the Access Bank address map; the current value of the BSR is ignored entirely. (c) 2009 Microchip Technology Inc. Using this "forced" addressing allows the instruction to operate on a data address in a single cycle, without updating the BSR first. For 8-bit addresses of 80h and above, this means that users can evaluate and operate on SFRs more efficiently. The Access RAM below 80h is a good place for data values that the user might need to access rapidly, such as immediate computational results or common program variables. Access RAM also allows for faster and more code efficient context saving and switching of variables. The mapping of the Access Bank is slightly different when the extended instruction set is enabled (XINST Configuration bit = 1). This is discussed in more detail in Section 5.5.3 "Mapping the Access Bank in Indexed Literal Offset Addressing Mode". 5.3.3 GENERAL PURPOSE REGISTER FILE PIC18 devices may have banked memory in the GPR area. This is data RAM, which is available for use by all instructions. GPRs start at the bottom of Bank 0 (address 000h) and grow upwards towards the bottom of the SFR area. GPRs are not initialized by a Power-on Reset and are unchanged on all other Resets. DS39636D-page 65 PIC18F2X1X/4X1X 5.3.4 SPECIAL FUNCTION REGISTERS The SFRs can be classified into two sets: those associated with the "core" device functionality (ALU, Resets and interrupts) and those related to the peripheral functions. The reset and interrupt registers are described in their respective chapters, while the ALU's STATUS register is described later in this section. Registers related to the operation of a peripheral feature are described in the chapter for that peripheral. The Special Function Registers (SFRs) are registers used by the CPU and peripheral modules for controlling the desired operation of the device. These registers are implemented as static RAM. SFRs start at the top of data memory (FFFh) and extend downward to occupy the top half of Bank 15 (F80h to FFFh). A list of these registers is given in Table 5-1 and Table 5-2. TABLE 5-1: The SFRs are typically distributed among the peripherals whose functions they control. Unused SFR locations are unimplemented and read as `0's. SPECIAL FUNCTION REGISTER MAP FOR PIC18F2X1X/4X1X DEVICES Address Name FFFh Address TOSU Name Address FDFh INDF2(1) POSTINC2(1) FBEh FBDh FDCh PREINC2 (1) FBCh FFEh TOSH FDEh FFDh TOSL FDDh POSTDEC2(1) FFCh STKPTR FFBh PCLATU FDBh PLUSW2(1) FFAh PCLATH FDAh FSR2H FBFh Name Address CCPR1H Name F9Fh IPR1 CCPR1L F9Eh PIR1 CCP1CON F9Dh PIE1 CCPR2H F9Ch --(2) FBBh CCPR2L F9Bh OSCTUNE FBAh CCP2CON F9Ah --(2) F99h --(2) FF9h PCL FD9h FSR2L FB9h --(2) FF8h TBLPTRU FD8h STATUS FB8h BAUDCON F98h --(2) F97h --(2) FF7h TBLPTRH FD7h TMR0H FB7h PWM1CON(3) FF6h TBLPTRL FD6h TMR0L FB6h ECCP1AS(3) F96h TRISE(3) FF5h TABLAT FD5h T0CON FB5h CVRCON F95h TRISD(3) FF4h PRODH FD4h --(2) FB4h CMCON F94h TRISC FF3h PRODL FD3h OSCCON FB3h TMR3H F93h TRISB FF2h INTCON FD2h HLVDCON FB2h TMR3L F92h TRISA FF1h INTCON2 FD1h WDTCON FB1h T3CON F91h --(2) FF0h INTCON3 FD0h RCON FB0h SPBRGH F90h --(2) FEFh INDF0(1) FCFh TMR1H FAFh SPBRG F8Fh --(2) FEEh POSTINC0(1) FCEh TMR1L FAEh RCREG F8Eh --(2) FEDh POSTDEC0(1) FCDh T1CON FADh TXREG F8Dh LATE(3) FECh PREINC0(1) FCCh TMR2 FACh TXSTA F8Ch LATD(3) FEBh PLUSW0(1) FCBh PR2 FABh RCSTA F8Bh LATC FEAh FSR0H FCAh T2CON FAAh --(2) F8Ah LATB FE9h FSR0L FC9h SSPBUF FA9h --(2) F89h LATA FA8h -- (2) F88h --(2) F87h --(2) FE8h WREG FE7h INDF1(1) FC8h FE6h POSTINC1(1) (1) FE5h POSTDEC1 SSPADD FC7h SSPSTAT FA7h --(2) FC6h SSPCON1 FA6h --(2) F86h --(2) (2) FC5h SSPCON2 FA5h -- F85h --(2) FC4h ADRESH FA4h --(2) F84h PORTE(3) F83h PORTD(3) FE4h PREINC1(1) FE3h PLUSW1(1) FC3h ADRESL FA3h --(2) FE2h FSR1H FC2h ADCON0 FA2h IPR2 F82h PORTC FE1h FSR1L FC1h ADCON1 FA1h PIR2 F81h PORTB FE0h BSR FC0h ADCON2 FA0h PIE2 F80h PORTA Note 1: 2: 3: This is not a physical register. Unimplemented registers are read as `0'. This register is not available on 28-pin devices. DS39636D-page 66 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 5-2: File Name REGISTER FILE SUMMARY (PIC18F2X1X/4X1X) Bit 7 Bit 6 Bit 5 -- -- -- Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Details on page: ---0 0000 51, 56 TOSH Top-of-Stack High Byte (TOS<15:8>) 0000 0000 51, 56 TOSL Top-of-Stack Low Byte (TOS<7:0>) 0000 0000 51, 56 00-0 0000 51, 57 TOSU STKPTR PCLATU STKFUL(6) STKUNF(6) -- -- -- -- Top-of-Stack Upper Byte (TOS<20:16>) Value on POR, BOR SP4 SP3 SP2 SP1 SP0 ---0 0000 51, 56 PCLATH Holding Register for PC<15:8> 0000 0000 51, 56 PCL PC Low Byte (PC<7:0>) 0000 0000 51, 56 --00 0000 51, 79 TBLPTRU -- -- bit 21 Holding Register for PC<20:16> Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) TBLPTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>) 0000 0000 51, 79 TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>) 0000 0000 51, 79 TABLAT Program Memory Table Latch 0000 0000 51, 79 PRODH Product Register High Byte xxxx xxxx 51, 81 PRODL Product Register Low Byte xxxx xxxx 51, 81 INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 51, 85 INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2 -- TMR0IP -- RBIP 1111 -1-1 51, 86 INT2IP INT1IP -- INT2IE INT1IE -- INT2IF INT1IF 11-0 0-00 51, 87 INTCON3 INDF0 Uses contents of FSR0 to address data memory - value of FSR0 not changed (not a physical register) N/A 51, 72 POSTINC0 Uses contents of FSR0 to address data memory - value of FSR0 post-incremented (not a physical register) N/A 51, 72 POSTDEC0 Uses contents of FSR0 to address data memory - value of FSR0 post-decremented (not a physical register) N/A 51, 72 PREINC0 Uses contents of FSR0 to address data memory - value of FSR0 pre-incremented (not a physical register) N/A 51, 72 PLUSW0 Uses contents of FSR0 to address data memory - value of FSR0 pre-incremented (not a physical register) - value of FSR0 offset by W N/A 51, 72 FSR0H ---- 0000 51, 72 FSR0L Indirect Data Memory Address Pointer 0 Low Byte -- -- -- -- Indirect Data Memory Address Pointer 0 High Byte xxxx xxxx 51, 72 WREG Working Register xxxx xxxx 51 INDF1 Uses contents of FSR1 to address data memory - value of FSR1 not changed (not a physical register) N/A 51, 72 POSTINC1 Uses contents of FSR1 to address data memory - value of FSR1 post-incremented (not a physical register) N/A 51, 72 POSTDEC1 Uses contents of FSR1 to address data memory - value of FSR1 post-decremented (not a physical register) N/A 51, 72 PREINC1 Uses contents of FSR1 to address data memory - value of FSR1 pre-incremented (not a physical register) N/A 51, 72 PLUSW1 Uses contents of FSR1 to address data memory - value of FSR1 pre-incremented (not a physical register) - value of FSR1 offset by W N/A 51, 72 ---- 0000 52, 72 FSR1H -- FSR1L -- -- -- Indirect Data Memory Address Pointer 1 High Byte Indirect Data Memory Address Pointer 1 Low Byte BSR -- -- -- -- Bank Select Register xxxx xxxx 52, 72 ---- 0000 52, 61 INDF2 Uses contents of FSR2 to address data memory - value of FSR2 not changed (not a physical register) N/A 52, 72 POSTINC2 Uses contents of FSR2 to address data memory - value of FSR2 post-incremented (not a physical register) N/A 52, 72 POSTDEC2 Uses contents of FSR2 to address data memory - value of FSR2 post-decremented (not a physical register) N/A 52, 72 PREINC2 Uses contents of FSR2 to address data memory - value of FSR2 pre-incremented (not a physical register) N/A 52, 72 PLUSW2 Uses contents of FSR2 to address data memory - value of FSR2 pre-incremented (not a physical register) - value of FSR2 offset by W N/A 52, 72 ---- 0000 52, 72 FSR2H -- FSR2L -- -- -- Indirect Data Memory Address Pointer 2 High Byte Indirect Data Memory Address Pointer 2 Low Byte STATUS Legend: Note 1: 2: 3: 4: 5: 6: -- -- -- N OV Z DC C xxxx xxxx 52, 72 ---x xxxx 52, 70 x = unknown, u = unchanged, -- = unimplemented, q = value depends on condition The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". These registers and/or bits are not implemented on 28-pin devices and are read as `0'. Reset values are shown for 40/44-pin devices; individual unimplemented bits should be interpreted as `-'. The PLLEN bit is only available in specific oscillator configuration; otherwise it is disabled and reads as `0'. See Section 2.6.4 "PLL in INTOSC Modes". The RE3 bit is only available when Master Clear Reset is disabled (MCLRE Configuration bit = 0). Otherwise, RE3 reads as `0'. This bit is read-only. RA6/RA7 and their associated latch and direction bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. Bit 7 and bit 6 are cleared by user software or by a POR. (c) 2009 Microchip Technology Inc. DS39636D-page 67 PIC18F2X1X/4X1X TABLE 5-2: File Name REGISTER FILE SUMMARY (PIC18F2X1X/4X1X) (CONTINUED) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Details on page: TMR0H Timer0 Register High Byte 0000 0000 52, 117 TMR0L Timer0 Register Low Byte xxxx xxxx 52, 117 52, 115 T0CON TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 1111 1111 OSCCON IDLEN IRCF2 IRCF1 IRCF0 OSTS IOFS SCS1 SCS0 0100 q000 32, 52 HLVDCON VDIRMAG -- IRVST HLVDEN HLVDL3 HLVDL2 HLVDL1 HLVDL0 0-00 0101 52, 233 WDTCON -- -- -- -- -- -- -- SWDTEN --- ---0 52, 249 -- RI TO PD POR BOR RCON IPEN SBOREN (1) 0q-1 11q0 44, 50, 94 TMR1H Timer1 Register High Byte xxxx xxxx 52, 123 TMR1L Timer1 Register Low Bytes xxxx xxxx 52, 123 T1CON RD16 T1RUN TMR2 Timer2 Register PR2 Timer2 Period Register T2CON -- T2OUTPS3 T1CKPS1 T2OUTPS2 T1CKPS0 T2OUTPS1 T1OSCEN T2OUTPS0 T1SYNC TMR2ON TMR1CS T2CKPS1 SSPBUF SSP Receive Buffer/Transmit Register SSPADD SSP Address Register in I2C Slave mode. SSP Baud Rate Reload Register in I2C Master mode. TMR1ON T2CKPS0 0000 0000 52, 119 0000 0000 52, 126 1111 1111 52, 126 -000 0000 52, 125 xxxx xxxx 52, 161, 162 0000 0000 52, 162 SSPSTAT SMP CKE D/A P S R/W UA BF 0000 0000 52, 154, 163 SSPCON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 52, 155, 164 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN SSPCON2 0000 0000 52, 165 ADRESH A/D Result Register High Byte xxxx xxxx 53, 222 ADRESL A/D Result Register Low Byte xxxx xxxx 53, 222 ADCON0 -- -- CHS3 CHS2 CHS1 CHS0 GO/DONE ADON --00 0000 53, 213 ADCON1 -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 --00 0qqq 53, 214 ADFM -- ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 ADCON2 0-00 0000 53, 215 CCPR1H Capture/Compare/PWM Register 1 High Byte xxxx xxxx 53, 132 CCPR1L Capture/Compare/PWM Register 1 Low Byte xxxx xxxx 53, 132 0000 0000 53, 131, 139 53, 132 CCP1CON P1M1(2) P1M0(2) DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 CCPR2H Capture/Compare/PWM Register 2 High Byte xxxx xxxx CCPR2L Capture/Compare/PWM Register 2 Low Byte xxxx xxxx 53, 132 --00 0000 53, 131 CCP2CON -- BAUDCON ABDOVF RCIDL -- SCKP BRG16 -- WUE ABDEN 01-0 0-00 53, 196 PWM1CON PRSEN PDC6(2) PDC5(2) PDC4(2) PDC3(2) PDC2(2) PDC1(2) PDC0(2) 0000 0000 53, 148 ECCP1AS ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1(2) PSSBD0(2) 0000 0000 53, 149 CVRCON CVREN CVROE CVRR CVRSS CVR3 CVR2 CVR1 CVR0 0000 0000 53, 229 CMCON C2OUT C1OUT C2INV C1INV CIS CM2 CM1 CM0 0000 0111 53, 223 -- DC2B1 DC2B0 CCP2M3 CCP2M2 CCP2M1 CCP2M0 TMR3H Timer3 Register High Byte xxxx xxxx 53, 129 TMR3L Timer3 Register Low Byte xxxx xxxx 53, 129 0000 0000 53, 127 T3CON RD16 Legend: Note 1: 2: 3: 4: 5: 6: T3CCP2 T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON x = unknown, u = unchanged, -- = unimplemented, q = value depends on condition The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". These registers and/or bits are not implemented on 28-pin devices and are read as `0'. Reset values are shown for 40/44-pin devices; individual unimplemented bits should be interpreted as `-'. The PLLEN bit is only available in specific oscillator configuration; otherwise it is disabled and reads as `0'. See Section 2.6.4 "PLL in INTOSC Modes". The RE3 bit is only available when Master Clear Reset is disabled (MCLRE Configuration bit = 0). Otherwise, RE3 reads as `0'. This bit is read-only. RA6/RA7 and their associated latch and direction bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. Bit 7 and bit 6 are cleared by user software or by a POR. DS39636D-page 68 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 5-2: File Name REGISTER FILE SUMMARY (PIC18F2X1X/4X1X) (CONTINUED) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Details on page: SPBRGH EUSART Baud Rate Generator Register High Byte 0000 0000 53, 197 SPBRG EUSART Baud Rate Generator Register Low Byte 0000 0000 53, 197 RCREG EUSART Receive Register 0000 0000 53, 204 TXREG EUSART Transmit Register 0000 0000 53, 202 TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 53, 194 RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 53, 195 IPR2 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 11-- 1111 54, 93 PIR2 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 00-- 0000 54, 89 PIE2 OSCFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE 00-- 0000 54, 91 IPR1 PSPIP(2) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 1111 1111 54, 92 54, 88 PIR1 PSPIF(2) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 PIE1 PSPIE(2) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 54, 90 OSCTUNE INTSRC PLLEN(3) -- TUN4 TUN3 TUN2 TUN1 TUN0 0q-0 0000 29, 54 IBF OBF IBOV PSPMODE -- TRISE2 TRISE1 TRISE0 TRISE(2) 0000 -111 54, 110 PORTD Data Direction Control Register 1111 1111 54, 106 TRISC PORTC Data Direction Control Register 1111 1111 54, 103 TRISB PORTB Data Direction Control Register 1111 1111 54, 100 TRISD(2) TRISA TRISA7(5) TRISA6(5) LATE(2) -- -- Data Direction Control Register for PORTA -- -- -- PORTE Data Latch Register (Read and Write to Data Latch) 1111 1111 54, 97 ---- -xxx 54, 109 LATD(2) PORTD Data Latch Register (Read and Write to Data Latch) xxxx xxxx 54, 106 LATC PORTC Data Latch Register (Read and Write to Data Latch) xxxx xxxx 54, 103 LATB PORTB Data Latch Register (Read and Write to Data Latch) xxxx xxxx 54, 100 LATA PORTE LATA7(6) LATA6(6) -- -- PORTA Data Latch Register (Read and Write to Data Latch) -- -- RE3(4) xxxx xxxx 54, 97 RE2(2) RE1(2) RE0(2) ---- xxxx 54, 109 PORTD(2) RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx xxxx 54, 106 PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 xxxx xxxx 54, 103 PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx xxxx 54, 100 PORTA RA7(5) RA6(5) RA5 RA4 RA3 RA2 RA1 RA0 xx0x 0000 54, 97 Legend: Note 1: 2: 3: 4: 5: 6: x = unknown, u = unchanged, -- = unimplemented, q = value depends on condition The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". These registers and/or bits are not implemented on 28-pin devices and are read as `0'. Reset values are shown for 40/44-pin devices; individual unimplemented bits should be interpreted as `-'. The PLLEN bit is only available in specific oscillator configuration; otherwise it is disabled and reads as `0'. See Section 2.6.4 "PLL in INTOSC Modes". The RE3 bit is only available when Master Clear Reset is disabled (MCLRE Configuration bit = 0). Otherwise, RE3 reads as `0'. This bit is read-only. RA6/RA7 and their associated latch and direction bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. Bit 7 and bit 6 are cleared by user software or by a POR. (c) 2009 Microchip Technology Inc. DS39636D-page 69 PIC18F2X1X/4X1X 5.3.5 STATUS REGISTER The STATUS register, shown in Register 5-2, contains the arithmetic status of the ALU. As with any other SFR, it can be the operand for any instruction. If the STATUS register is the destination for an instruction that affects the Z, DC, C, OV or N bits, the results of the instruction are not written; instead, the status is updated according to the instruction performed. Therefore, the result of an instruction with the STATUS register as its destination may be different than intended. As an example, CLRF STATUS will set the Z bit and leave the remaining Status bits unchanged (`000u u1uu'). REGISTER 5-2: It is recommended that only BCF, BSF, SWAPF, MOVFF and MOVWF instructions are used to alter the STATUS register, because these instructions do not affect the Z, C, DC, OV or N bits in the STATUS register. For other instructions that do not affect Status bits, see the instruction set summaries in Table 23-2 and Table 23-3. Note: The C and DC bits operate as the borrow and digit borrow bits, respectively, in subtraction. STATUS REGISTER U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x -- -- -- N OV Z DC C bit 7 bit 0 bit 7-5 Unimplemented: Read as `0' bit 4 N: Negative bit This bit is used for signed arithmetic (2's complement). It indicates whether the result was negative (ALU MSB = 1). 1 = Result was negative 0 = Result was positive bit 3 OV: Overflow bit This bit is used for signed arithmetic (2's complement). It indicates an overflow of the 7-bit magnitude which causes the sign bit (bit 7 of the result) to change state. 1 = Overflow occurred for signed arithmetic (in this arithmetic operation) 0 = No overflow occurred bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit carry/borrow bit For ADDWF, ADDLW, SUBLW and SUBWF instructions: 1 = A carry-out from the 4th low-order bit of the result occurred 0 = No carry-out from the 4th low-order bit of the result Note: bit 0 For borrow, the polarity is reversed. A subtraction is executed by adding the 2's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either bit 4 or bit 3 of the source register. C: Carry/borrow bit For ADDWF, ADDLW, SUBLW and SUBWF instructions: 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note: For borrow, the polarity is reversed. A subtraction is executed by adding the 2's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low-order bit of the source register. Legend: DS39636D-page 70 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 5.4 Data Addressing Modes Note: The execution of some instructions in the core PIC18 instruction set are changed when the PIC18 extended instruction set is enabled. See Section 5.5 "Data Memory and the Extended Instruction Set" for more information. The data memory space can be addressed in several ways. For most instructions, the addressing mode is fixed. Other instructions may use up to three modes, depending on which operands are used and whether or not the extended instruction set is enabled. The addressing modes are: * * * * Inherent Literal Direct Indirect An additional addressing mode, Indexed Literal Offset, is available when the extended instruction set is enabled (XINST Configuration bit = 1). Its operation is discussed in greater detail in Section 5.5.1 "Indexed Addressing with Literal Offset". 5.4.1 INHERENT AND LITERAL ADDRESSING Many PIC18 control instructions do not need any argument at all; they either perform an operation that globally affects the device or they operate implicitly on one register. This addressing mode is known as Inherent Addressing. Examples include SLEEP, RESET and DAW. Other instructions work in a similar way but require an additional explicit argument in the opcode. This is known as Literal Addressing mode because they require some literal value as an argument. Examples include ADDLW and MOVLW which, respectively, add or move a literal value to the W register. Other examples include CALL and GOTO, which include a 20-bit program memory address. 5.4.2 DIRECT ADDRESSING Direct addressing specifies all or part of the source and/or destination address of the operation within the opcode itself. The options are specified by the arguments accompanying the instruction. In the core PIC18 instruction set, bit-oriented and byteoriented instructions use some version of direct addressing by default. All of these instructions include some 8-bit literal address as their Least Significant Byte. This address specifies either a register address in one of the banks of data RAM (Section 5.3.3 "General Purpose Register File") or a location in the Access Bank (Section 5.3.2 "Access Bank") as the data source for the instruction. (c) 2009 Microchip Technology Inc. The Access RAM bit `a' determines how the address is interpreted. When `a' is `1', the contents of the BSR (Section 5.3.1 "Bank Select Register (BSR)") are used with the address to determine the complete 12-bit address of the register. When `a' is `0', the address is interpreted as being a register in the Access Bank. Addressing that uses the Access RAM is sometimes also known as Direct Forced Addressing mode. A few instructions, such as MOVFF, include the entire 12-bit address (either source or destination) in their opcodes. In these cases, the BSR is ignored entirely. The destination of the operation's results is determined by the destination bit `d'. When `d' is `1', the results are stored back in the source register, overwriting its original contents. When `d' is `0', the results are stored in the W register. Instructions without the `d' argument have a destination that is implicit in the instruction; their destination is either the target register being operated on or the W register. 5.4.3 INDIRECT ADDRESSING Indirect addressing allows the user to access a location in data memory without giving a fixed address in the instruction. This is done by using File Select Registers (FSRs) as pointers to the locations to be read or written to. Since the FSRs are themselves located in RAM as Special File Registers, they can also be directly manipulated under program control. This makes FSRs very useful in implementing data structures, such as tables and arrays in data memory. The registers for indirect addressing are also implemented with Indirect File Operands (INDFs) that permit automatic manipulation of the pointer value with auto-incrementing, auto-decrementing or offsetting with another value. This allows for efficient code, using loops, such as the example of clearing an entire RAM bank in Example 5-5. EXAMPLE 5-5: NEXT LFSR CLRF BTFSS BRA CONTINUE HOW TO CLEAR RAM (BANK 1) USING INDIRECT ADDRESSING FSR0, 100h ; POSTINC0 ; Clear INDF ; register then ; inc pointer FSR0H, 1 ; All done with ; Bank1? NEXT ; NO, clear next ; YES, continue DS39636D-page 71 PIC18F2X1X/4X1X 5.4.3.1 FSR Registers and the INDF Operand 5.4.3.2 At the core of indirect addressing are three sets of registers: FSR0, FSR1 and FSR2. Each represents a pair of 8-bit registers, FSRnH and FSRnL. The four upper bits of the FSRnH register are not used so each FSR pair holds a 12-bit value. This represents a value that can address the entire range of the data memory in a linear fashion. The FSR register pairs, then, serve as pointers to data memory locations. In addition to the INDF operand, each FSR register pair also has four additional indirect operands. Like INDF, these are "virtual" registers that cannot be indirectly read or written to. Accessing these registers actually accesses the associated FSR register pair, but also performs a specific action on its stored value. They are: * POSTDEC: accesses the FSR value, then automatically decrements it by 1 afterwards * POSTINC: accesses the FSR value, then automatically increments it by 1 afterwards * PREINC: increments the FSR value by 1, then uses it in the operation * PLUSW: adds the signed value of the W register (range of -127 to 128) to that of the FSR and uses the new value in the operation. Indirect addressing is accomplished with a set of Indirect File Operands, INDF0 through INDF2. These can be thought of as "virtual" registers: they are mapped in the SFR space but are not physically implemented. Reading or writing to a particular INDF register actually accesses its corresponding FSR register pair. A read from INDF1, for example, reads the data at the address indicated by FSR1H:FSR1L. Instructions that use the INDF registers as operands actually use the contents of their corresponding FSR as a pointer to the instruction's target. The INDF operand is just a convenient way of using the pointer. In this context, accessing an INDF register uses the value in the FSR registers without changing them. Similarly, accessing a PLUSW register gives the FSR value offset by that in the W register; neither value is actually changed in the operation. Accessing the other virtual registers changes the value of the FSR registers. Because indirect addressing uses a full 12-bit address, data RAM banking is not necessary. Thus, the current contents of the BSR and the Access RAM bit have no effect on determining the target address. FIGURE 5-9: FSR Registers and POSTINC, POSTDEC, PREINC and PLUSW Operations on the FSRs with POSTDEC, POSTINC and PREINC affect the entire register pair; that is, rollovers of the FSRnL register from FFh to 00h carry over to the FSRnH register. On the other hand, results of these operations do not change the value of any flags in the STATUS register (e.g., Z, N, OV, etc.). INDIRECT ADDRESSING 000h Using an instruction with one of the indirect addressing registers as the operand.... Bank 0 ADDWF, INDF1, 1 100h Bank 1 200h ...uses the 12-bit address stored in the FSR pair associated with that register.... 300h FSR1H:FSR1L 7 0 x x x x 1 1 1 0 7 0 Bank 2 Bank 3 through Bank 13 1 1 0 0 1 1 0 0 ...to determine the data memory location to be used in that operation. In this case, the FSR1 pair contains ECCh. This means the contents of location ECCh will be added to that of the W register and stored back in ECCh. E00h Bank 14 F00h FFFh Bank 15 Data Memory DS39636D-page 72 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X The PLUSW register can be used to implement a form of indexed addressing in the data memory space. By manipulating the value in the W register, users can reach addresses that are fixed offsets from pointer addresses. In some applications, this can be used to implement some powerful program control structure, such as software stacks, inside of data memory. 5.4.3.3 Operations by FSRs on FSRs Indirect addressing operations that target other FSRs or virtual registers represent special cases. For example, using an FSR to point to one of the virtual registers will not result in successful operations. As a specific case, assume that FSR0H:FSR0L contains FE7h, the address of INDF1. Attempts to read the value of the INDF1 using INDF0 as an operand will return 00h. Attempts to write to INDF1 using INDF0 as the operand will result in a NOP. On the other hand, using the virtual registers to write to an FSR pair may not occur as planned. In these cases, the value will be written to the FSR pair but without any incrementing or decrementing. Thus, writing to INDF2 or POSTDEC2 will write the same value to the FSR2H:FSR2L. Since the FSRs are physical registers mapped in the SFR space, they can be manipulated through all direct operations. Users should proceed cautiously when working on these registers, particularly if their code uses indirect addressing. 5.5.1 INDEXED ADDRESSING WITH LITERAL OFFSET Enabling the PIC18 extended instruction set changes the behavior of indirect addressing using the FSR2 register pair within access RAM. Under the proper conditions, instructions that use the Access Bank - that is, most bit-oriented and byte-oriented instructions - can invoke a form of indexed addressing using an offset specified in the instruction. This special addressing mode is known as Indexed Addressing with Literal Offset, or Indexed Literal Offset mode. When using the extended instruction set, this addressing mode requires the following: * The use of the Access Bank is forced (`a' = 0); and * The file address argument is less than or equal to 5Fh. Under these conditions, the file address of the instruction is not interpreted as the lower byte of an address (used with the BSR in direct addressing), or as an 8-bit address in the Access Bank. Instead, the value is interpreted as an offset value to an Address Pointer, specified by FSR2. The offset and the contents of FSR2 are added to obtain the target address of the operation. 5.5.2 INSTRUCTIONS AFFECTED BY INDEXED LITERAL OFFSET MODE Similarly, operations by indirect addressing are generally permitted on all other SFRs. Users should exercise the appropriate caution that they do not inadvertently change settings that might affect the operation of the device. Any of the core PIC18 instructions that can use direct addressing are potentially affected by the Indexed Literal Offset Addressing mode. This includes all byte-oriented and bit-oriented instructions, or almost one-half of the standard PIC18 instruction set. Instructions that only use Inherent or Literal Addressing modes are unaffected. 5.5 Additionally, byte-oriented and bit-oriented instructions are not affected if they do not use the Access Bank (Access RAM bit is `1'), or include a file address of 60h or above. Instructions meeting these criteria will continue to execute as before. A comparison of the different possible addressing modes when the extended instruction set is enabled is shown in Figure 5-10. Data Memory and the Extended Instruction Set Enabling the PIC18 extended instruction set (XINST Configuration bit = 1) significantly changes certain aspects of data memory and its addressing. Specifically, the use of the Access Bank for many of the core PIC18 instructions is different; this is due to the introduction of a new addressing mode for the data memory space. What does not change is just as important. The size of the data memory space is unchanged, as well as its linear addressing. The SFR map remains the same. Core PIC18 instructions can still operate in both Direct and Indirect Addressing mode; inherent and literal instructions do not change at all. Indirect addressing with FSR0 and FSR1 also remain unchanged. (c) 2009 Microchip Technology Inc. Those who desire to use bit-oriented or byte-oriented instructions in the Indexed Literal Offset mode should note the changes to assembler syntax for this mode. This is described in more detail in Section 23.2.1 "Extended Instruction Syntax". DS39636D-page 73 PIC18F2X1X/4X1X FIGURE 5-10: COMPARING ADDRESSING OPTIONS FOR BIT-ORIENTED AND BYTE-ORIENTED INSTRUCTIONS (EXTENDED INSTRUCTION SET ENABLED) EXAMPLE INSTRUCTION: ADDWF, f, d, a (Opcode: 0010 01da ffff ffff) When `a' = 0 and f 60h: The instruction executes in Direct Forced mode. `f' is interpreted as a location in the Access RAM between 060h and 0FFh. This is the same as locations 060h to 07Fh (Bank 0) and F80h to FFFh (Bank 15) of data memory. 000h Locations below 60h are not available in this addressing mode. F00h 060h 080h Note that in this mode, the correct syntax is now: ADDWF [k], d where `k' is the same as `f'. When `a' = 1 (all values of f): The instruction executes in Direct mode (also known as Direct Long mode). `f' is interpreted as a location in one of the 16 banks of the data memory space. The bank is designated by the Bank Select Register (BSR). The address can be in any implemented bank in the data memory space. 00h Bank 1 through Bank 14 60h 80h Access RAM Valid range for `f' FFh Bank 15 F80h SFRs FFFh When `a' = 0 and f 5Fh: The instruction executes in Indexed Literal Offset mode. `f' is interpreted as an offset to the address value in FSR2. The two are added together to obtain the address of the target register for the instruction. The address can be anywhere in the data memory space. Bank 0 100h Data Memory 000h Bank 0 080h 100h 001001da ffffffff Bank 1 through Bank 14 FSR2H FSR2L F00h Bank 15 F80h SFRs FFFh Data Memory BSR 00000000 000h Bank 0 080h 100h Bank 1 through Bank 14 001001da ffffffff F00h Bank 15 F80h SFRs FFFh DS39636D-page 74 Data Memory (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 5.5.3 MAPPING THE ACCESS BANK IN INDEXED LITERAL OFFSET ADDRESSING MODE The use of Indexed Literal Offset Addressing mode effectively changes how the first 96 locations of access RAM (00h to 5Fh) are mapped. Rather than containing just the contents of the bottom half of Bank 0, this mode maps the contents from Bank 0 and a user defined "window" that can be located anywhere in the data memory space. The value of FSR2 establishes the lower boundary of the addresses mapped into the window, while the upper boundary is defined by FSR2 plus 95 (5Fh). Addresses in the Access RAM above 5Fh are mapped as previously described (see Section 5.3.2 "Access Bank"). An example of Access Bank remapping in this addressing mode is shown in Figure 5-11. FIGURE 5-11: Remapping of the Access Bank applies only to operations using the Indexed Literal Offset Addressing mode. Operations that use the BSR (Access RAM bit is `1') will continue to use direct addressing as before. 5.6 PIC18 Instruction Execution and the Extended Instruction Set Enabling the extended instruction set adds eight additional commands to the existing PIC18 instruction set. These instructions are executed as described in Section 23.2 "Extended Instruction Set". REMAPPING THE ACCESS BANK WITH INDEXED LITERAL OFFSET ADDRESSING Example Situation: ADDWF f, d, a FSR2H:FSR2L = 120h Locations in the region from the FSR2 Pointer (120h) to the pointer plus 05Fh (17Fh) are mapped to the bottom of the Access RAM (000h-05Fh). 000h 05Fh 07Fh 100h 120h 17Fh 200h Bank 0 addresses below 5Fh can still be addressed by using the BSR. Bank 0 Bank 1 Window Bank 1 00h Bank 1 "Window" 5Fh Locations in Bank 0 from 060h to 07Fh are mapped, as usual, to the middle of the Access Bank. Special File Registers at F80h through FFFh are mapped to 80h through FFh, as usual. Bank 0 Bank 0 Bank 2 through Bank 14 7Fh 80h SFRs FFh Access Bank F00h Bank 15 F80h FFFh SFRs Data Memory (c) 2009 Microchip Technology Inc. DS39636D-page 75 PIC18F2X1X/4X1X NOTES: DS39636D-page 76 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 6.0 FLASH PROGRAM MEMORY In PIC18F2X1X/4X1X devices, the program memory is implemented as read-only Flash memory. It is readable over the entire VDD range during normal operation. A read from program memory is executed on one byte at a time. 6.1 Table Reads For PIC18 devices, there are two operations that allow the processor to move bytes between the program memory space and the data RAM: table read (TBLRD) and table write (TBLWT). Table read operations retrieve data from program memory and place it into the data RAM space. Figure 6-1 shows the operation of a table read with program memory and data RAM. Table reads work with byte entities. A table block containing data, rather than program instructions, is not required to be word-aligned. Therefore, a table block can start and end at any byte address. Because the program memory cannot be written to or erased under normal operation, the TBLWT operation is not discussed here. Note 1: Although it cannot be used in PIC18F2X1X/4X1X devices in normal operation, the TBLWT instruction is still implemented in the instruction set. Executing the instruction takes two instruction cycles, but effectively results in a NOP. 2: The TBLWT instruction is available only in programming modes and is used during In-Circuit Serial ProgrammingTM (ICSPTM). The program memory space is 16 bits wide, while the data RAM space is 8 bits wide. Table reads and table writes move data between these two memory spaces through an 8-bit register, TABLAT. FIGURE 6-1: TABLE READ OPERATION Instruction: TBLRD* Program Memory Table Pointer(1) TBLPTRU TBLPTRH Table Latch (8-bit) TBLPTRL TABLAT Program Memory (TBLPTR) Note 1: Table Pointer register points to a byte in program memory. (c) 2009 Microchip Technology Inc. DS39636D-page 77 PIC18F2X1X/4X1X 6.2 Control Registers TABLE 6-1: Two control registers are used in conjunction with the TBLRD instruction: the TABLAT register and the TBLPTR register set. TABLE POINTER OPERATIONS WITH TBLRD INSTRUCTIONS Example Operation on Table Pointer 6.2.1 TABLAT - TABLE LATCH REGISTER TBLRD* The Table Latch (TABLAT) is an 8-bit register mapped into the SFR space. The Table Latch register is used to hold 8-bit data during data transfers between program memory and data RAM. TBLRD*+ TBLPTR is incremented after the read TBLRD*- TBLPTR is decremented after the read TBLRD+* TBLPTR is incremented before the read 6.2.2 6.3 TBLPTR - TABLE POINTER REGISTER The Table Pointer register (TBLPTR) addresses a byte within the program memory. It is comprised of three SFR registers: Table Pointer Upper Byte, Table Pointer High Byte and Table Pointer Low Byte (TBLPTRU:TBLPTRH:TBLPTRL). Only the lower six bits of TBLPTRU are used with TBLPTRH and TBLPTRL, to form a 22-bit wide pointer. The contents of TBLPTR indicate a location in program memory space. The low-order 21 bits allow the device to address the full 2 Mbytes of program memory space. The 22nd bit allows access to the configuration space, including the Device ID, user ID locations and the Configuration bits. The TBLPTR register set is updated when executing a TBLRD in one of four ways, based on the instruction's arguments. These are detailed in Table 6-1. These operations on the TBLPTR only affect the low-order 21 bits. TBLPTR is not modified Reading the Flash Program Memory The TBLRD instruction is used to retrieve data from program memory and place it into data RAM. Table reads from program memory are performed one byte at a time. TBLPTR points to a byte address in program space. Executing TBLRD places the byte pointed to into TABLAT. In addition, TBLPTR can be modified automatically for the next table read operation. The internal program memory is typically organized by words. The Least Significant bit of the address selects between the high and low bytes of the word. Figure 6-2 shows the interface between the internal program memory and the TABLAT. A typical method for reading data from program memory is shown in Example 6-1. When a TBLRD is executed, all 22 bits of the TBLPTR determine which byte is read from program memory into TABLAT. FIGURE 6-2: READS FROM FLASH PROGRAM MEMORY Program Memory (Even Byte Address) (Odd Byte Address) TBLPTR = xxxxx1 Instruction Register (IR) DS39636D-page 78 FETCH TBLRD TBLPTR = xxxxx0 TABLAT Read Register (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X EXAMPLE 6-1: READING A FLASH PROGRAM MEMORY WORD MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CODE_ADDR_UPPER TBLPTRU CODE_ADDR_HIGH TBLPTRH CODE_ADDR_LOW TBLPTRL ; Load TBLPTR with the base ; address of the word READ_WORD TBLRD*+ MOVF MOVWF TBLRD*+ MOVF MOVF TABLE 6-2: Name TBLPTRU ; read into TABLAT and increment ; get data TABLAT, W WORD_EVEN ; read into TABLAT and increment ; get data TABLAT, W WORD_ODD REGISTERS ASSOCIATED WITH READING PROGRAM FLASH MEMORY Bit 7 Bit 6 Bit 5 -- -- bit 21 Bit 4 Bit 3 Bit 2 Bit 1 Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) Bit 0 Reset Values on Page 51 TBPLTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>) 51 TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>) 51 TABLAT Program Memory Table Latch 51 Legend: -- = unimplemented, read as `0'. Shaded cells are not used during Flash access. (c) 2009 Microchip Technology Inc. DS39636D-page 79 PIC18F2X1X/4X1X NOTES: DS39636D-page 80 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 7.0 8 x 8 HARDWARE MULTIPLIER 7.1 Introduction EXAMPLE 7-1: MOVF MULWF All PIC18 devices include an 8 x 8 hardware multiplier as part of the ALU. The multiplier performs an unsigned operation and yields a 16-bit result that is stored in the product register pair, PRODH:PRODL. The multiplier's operation does not affect any flags in the STATUS register. ARG1, W ARG2 ; ; ARG1 * ARG2 -> ; PRODH:PRODL EXAMPLE 7-2: Making multiplication a hardware operation allows it to be completed in a single instruction cycle. This has the advantages of higher computational throughput and reduced code size for multiplication algorithms and allows the PIC18 devices to be used in many applications previously reserved for digital signal processors. A comparison of various hardware and software multiply operations, along with the savings in memory and execution time, is shown in Table 7-1. 7.2 8 x 8 UNSIGNED MULTIPLY ROUTINE 8 x 8 SIGNED MULTIPLY ROUTINE MOVF MULWF ARG1, W ARG2 BTFSC SUBWF ARG2, SB PRODH, F MOVF BTFSC SUBWF ARG2, W ARG1, SB PRODH, F Operation ; ; ; ; ; ARG1 * ARG2 -> PRODH:PRODL Test Sign Bit PRODH = PRODH - ARG1 ; Test Sign Bit ; PRODH = PRODH ; - ARG2 Example 7-1 shows the instruction sequence for an 8 x 8 unsigned multiplication. Only one instruction is required when one of the arguments is already loaded in the WREG register. Example 7-2 shows the sequence to do an 8 x 8 signed multiplication. To account for the sign bits of the arguments, each argument's Most Significant bit (MSb) is tested and the appropriate subtractions are done. TABLE 7-1: PERFORMANCE COMPARISON FOR VARIOUS MULTIPLY OPERATIONS Routine 8 x 8 unsigned 8 x 8 signed 16 x 16 unsigned 16 x 16 signed Multiply Method Program Memory (Words) Cycles (Max) @ 40 MHz @ 10 MHz @ 4 MHz Without hardware multiply 13 69 6.9 s 27.6 s 69 s Time Hardware multiply 1 1 100 ns 400 ns 1 s Without hardware multiply 33 91 9.1 s 36.4 s 91 s Hardware multiply 6 6 600 ns 2.4 s 6 s Without hardware multiply 21 242 24.2 s 96.8 s 242 s Hardware multiply 28 28 2.8 s 11.2 s 28 s Without hardware multiply 52 254 25.4 s 102.6 s 254 s Hardware multiply 35 40 4.0 s 16.0 s 40 s (c) 2009 Microchip Technology Inc. DS39636D-page 81 PIC18F2X1X/4X1X Example 7-3 shows the sequence to do a 16 x 16 unsigned multiplication. Equation 7-1 shows the algorithm that is used. The 32-bit result is stored in four registers (RES3:RES0). EQUATION 7-1: RES3:RES0 = = EXAMPLE 7-3: 16 x 16 UNSIGNED MULTIPLICATION ALGORITHM ARG1H:ARG1L * ARG2H:ARG2L (ARG1H * ARG2H * 216) + (ARG1H * ARG2L * 28) + (ARG1L * ARG2H * 28) + (ARG1L * ARG2L) EQUATION 7-2: RES3:RES0 = ARG1H:ARG1L * ARG2H:ARG2L = (ARG1H * ARG2H * 216) + (ARG1H * ARG2L * 28) + (ARG1L * ARG2H * 28) + (ARG1L * ARG2L) + (-1 * ARG2H<7> * ARG1H:ARG1L * 216) + (-1 * ARG1H<7> * ARG2H:ARG2L * 216) EXAMPLE 7-4: 16 x 16 UNSIGNED MULTIPLY ROUTINE MOVF MULWF ARG1L, W ARG2L MOVFF MOVFF PRODH, RES1 PRODL, RES0 MOVF MULWF ARG1H, W ARG2H MOVFF MOVFF PRODH, RES3 PRODL, RES2 MOVF MULWF ARG1L, W ARG2H MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F MOVF MULWF ARG1H, W ARG2L MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F ; ARG1L * ARG2L-> ; PRODH:PRODL ; ; ARG1L * ARG2H-> PRODH:PRODL Add cross products ARG1H * ARG2L-> PRODH:PRODL Add cross products Example 7-4 shows the sequence to do a 16 x 16 signed multiply. Equation 7-2 shows the algorithm used. The 32-bit result is stored in four registers (RES3:RES0). To account for the sign bits of the arguments, the MSb for each argument pair is tested and the appropriate subtractions are done. DS39636D-page 82 ARG1L, W ARG2L MOVFF MOVFF PRODH, RES1 PRODL, RES0 MOVF MULWF ARG1H, W ARG2H MOVFF MOVFF PRODH, RES3 PRODL, RES2 MOVF MULWF ARG1L, W ARG2H MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F MOVF MULWF ARG1H, W ARG2L MOVF ADDWF MOVF ADDWFC CLRF ADDWFC PRODL, W RES1, F PRODH, W RES2, F WREG RES3, F BTFSS BRA MOVF SUBWF MOVF SUBWFB ARG2H, 7 SIGN_ARG1 ARG1L, W RES2 ARG1H, W RES3 ; ARG2H:ARG2L neg? ; no, check ARG1 ; ; ; ARG1H, 7 CONT_CODE ARG2L, W RES2 ARG2H, W RES3 ; ARG1H:ARG1L neg? ; no, done ; ; ; ; ARG1L * ARG2L -> ; PRODH:PRODL ; ; ; ARG1H * ARG2H -> ; PRODH:PRODL ; ; ; ; ; ; ; ; ; ; ARG1L * ARG2H -> PRODH:PRODL Add cross products ; ; ; ; ; ; ; ; ; ; ; MOVF MULWF ; ; ; ; ; ; ; ; ; ; 16 x 16 SIGNED MULTIPLY ROUTINE ; ; ; ARG1H * ARG2H-> ; PRODH:PRODL ; ; 16 x 16 SIGNED MULTIPLICATION ALGORITHM ; ; ; ; ; ; ; ; ; ARG1H * ARG2L -> PRODH:PRODL Add cross products ; ; SIGN_ARG1 BTFSS BRA MOVF SUBWF MOVF SUBWFB ; CONT_CODE : (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 8.0 INTERRUPTS The PIC18F2X1X/4X1X devices have multiple interrupt sources and an interrupt priority feature that allows most interrupt sources to be assigned a high priority level or a low priority level. The high priority interrupt vector is at 0008h and the low priority interrupt vector is at 0018h. High priority interrupt events will interrupt any low priority interrupts that may be in progress. There are ten registers which are used to control interrupt operation. These registers are: * * * * * * * RCON INTCON INTCON2 INTCON3 PIR1, PIR2 PIE1, PIE2 IPR1, IPR2 It is recommended that the Microchip header files supplied with MPLAB(R) IDE be used for the symbolic bit names in these registers. This allows the assembler/ compiler to automatically take care of the placement of these bits within the specified register. In general, interrupt sources have three bits to control their operation. They are: * Flag bit to indicate that an interrupt event occurred * Enable bit that allows program execution to branch to the interrupt vector address when the flag bit is set * Priority bit to select high priority or low priority The interrupt priority feature is enabled by setting the IPEN bit (RCON<7>). When interrupt priority is enabled, there are two bits which enable interrupts globally. Setting the GIEH bit (INTCON<7>) enables all interrupts that have the priority bit set (high priority). Setting the GIEL bit (INTCON<6>) enables all interrupts that have the priority bit cleared (low priority). When the interrupt flag, enable bit and appropriate global interrupt enable bit are set, the interrupt will vector immediately to address 0008h or 0018h, depending on the priority bit setting. Individual interrupts can be disabled through their corresponding enable bits. (c) 2009 Microchip Technology Inc. When the IPEN bit is cleared (default state), the interrupt priority feature is disabled and interrupts are compatible with PIC(R) mid-range devices. In Compatibility mode, the interrupt priority bits for each source have no effect. INTCON<6> is the PEIE bit, which enables/disables all peripheral interrupt sources. INTCON<7> is the GIE bit, which enables/disables all interrupt sources. All interrupts branch to address 0008h in Compatibility mode. When an interrupt is responded to, the global interrupt enable bit is cleared to disable further interrupts. If the IPEN bit is cleared, this is the GIE bit. If interrupt priority levels are used, this will be either the GIEH or GIEL bit. High priority interrupt sources can interrupt a low priority interrupt. Low priority interrupts are not processed while high priority interrupts are in progress. The return address is pushed onto the stack and the PC is loaded with the interrupt vector address (0008h or 0018h). Once in the Interrupt Service Routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bits must be cleared in software before re-enabling interrupts to avoid recursive interrupts. The "return from interrupt" instruction, RETFIE, exits the interrupt routine and sets the GIE bit (GIEH or GIEL if priority levels are used), which re-enables interrupts. For external interrupt events, such as the INT pins or the PORTB input change interrupt, the interrupt latency will be three to four instruction cycles. The exact latency is the same for one or two-cycle instructions. Individual interrupt flag bits are set, regardless of the status of their corresponding enable bit or the GIE bit. Note: Do not use the MOVFF instruction to modify any of the interrupt control registers while any interrupt is enabled. Doing so may cause erratic microcontroller behavior. DS39636D-page 83 PIC18F2X1X/4X1X FIGURE 8-1: PIC18 INTERRUPT LOGIC Wake-up if in Idle or Sleep modes TMR0IF TMR0IE TMR0IP RBIF RBIE RBIP INT0IF INT0IE Interrupt to CPU Vector to Location 0008h INT1IF INT1IE INT1IP INT2IF INT2IE INT2IP SSPIF SSPIE SSPIP GIEH/GIE ADIF ADIE ADIP IPEN IPEN RCIF RCIE RCIP GIEL/PEIE IPEN Additional Peripheral Interrupts High Priority Interrupt Generation Low Priority Interrupt Generation SSPIF SSPIE SSPIP Interrupt to CPU Vector to Location 0018h TMR0IF TMR0IE TMR0IP ADIF ADIE ADIP RBIF RBIE RBIP RCIF RCIE RCIP Additional Peripheral Interrupts GIEH/GIE GIEL/PEIE INT1IF INT1IE INT1IP INT2IF INT2IE INT2IP DS39636D-page 84 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 8.1 INTCON Registers Note: The INTCON registers are readable and writable registers, which contain various enable, priority and flag bits. REGISTER 8-1: Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. INTCON REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-x GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF bit 7 bit 0 bit 7 GIE/GIEH: Global Interrupt Enable bit When IPEN = 0: 1 = Enables all unmasked interrupts 0 = Disables all interrupts When IPEN = 1: 1 = Enables all high priority interrupts 0 = Disables all interrupts bit 6 PEIE/GIEL: Peripheral Interrupt Enable bit When IPEN = 0: 1 = Enables all unmasked peripheral interrupts 0 = Disables all peripheral interrupts When IPEN = 1: 1 = Enables all low priority peripheral interrupts 0 = Disables all low priority peripheral interrupts bit 5 TMR0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 overflow interrupt 0 = Disables the TMR0 overflow interrupt bit 4 INT0IE: INT0 External Interrupt Enable bit 1 = Enables the INT0 external interrupt 0 = Disables the INT0 external interrupt bit 3 RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2 TMR0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1 INT0IF: INT0 External Interrupt Flag bit 1 = The INT0 external interrupt occurred (must be cleared in software) 0 = The INT0 external interrupt did not occur bit 0 RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state Note: A mismatch condition will continue to set this bit. Reading PORTB will end the mismatch condition and allow the bit to be cleared. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 85 PIC18F2X1X/4X1X REGISTER 8-2: INTCON2 REGISTER R/W-1 R/W-1 R/W-1 R/W-1 U-0 R/W-1 U-0 R/W-1 RBPU INTEDG0 INTEDG1 INTEDG2 -- TMR0IP -- RBIP bit 7 bit 0 bit 7 RBPU: PORTB Pull-up Enable bit 1 = All PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6 INTEDG0: External Interrupt 0 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 5 INTEDG1: External Interrupt 1 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 4 INTEDG2: External Interrupt 2 Edge Select bit 1 = Interrupt on rising edge 0 = Interrupt on falling edge bit 3 Unimplemented: Read as `0' bit 2 TMR0IP: TMR0 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 Unimplemented: Read as `0' bit 0 RBIP: RB Port Change Interrupt Priority bit 1 = High priority 0 = Low priority Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared Note: DS39636D-page 86 x = Bit is unknown Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 8-3: INTCON3 REGISTER R/W-1 R/W-1 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 INT2IP INT1IP -- INT2IE INT1IE -- INT2IF INT1IF bit 7 bit 0 bit 7 INT2IP: INT2 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 INT1IP: INT1 External Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 Unimplemented: Read as `0' bit 4 INT2IE: INT2 External Interrupt Enable bit 1 = Enables the INT2 external interrupt 0 = Disables the INT2 external interrupt bit 3 INT1IE: INT1 External Interrupt Enable bit 1 = Enables the INT1 external interrupt 0 = Disables the INT1 external interrupt bit 2 Unimplemented: Read as `0' bit 1 INT2IF: INT2 External Interrupt Flag bit 1 = The INT2 external interrupt occurred (must be cleared in software) 0 = The INT2 external interrupt did not occur bit 0 INT1IF: INT1 External Interrupt Flag bit 1 = The INT1 external interrupt occurred (must be cleared in software) 0 = The INT1 external interrupt did not occur Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared Note: (c) 2009 Microchip Technology Inc. x = Bit is unknown Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global interrupt enable bit. User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. This feature allows for software polling. DS39636D-page 87 PIC18F2X1X/4X1X 8.2 PIR Registers Note 1: Interrupt flag bits are set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the Global Interrupt Enable bit, GIE (INTCON<7>). The PIR registers contain the individual flag bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt Request (Flag) registers (PIR1 and PIR2). REGISTER 8-4: 2: User software should ensure the appropriate interrupt flag bits are cleared prior to enabling an interrupt and after servicing that interrupt. PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1 R/W-0 R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF bit 7 bit 7 bit 0 PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit(1) 1 = A read or a write operation has taken place (must be cleared in software) 0 = No read or write has occurred Note 1: This bit is unimplemented on 28-pin devices and is read as `0'. bit 6 ADIF: A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete bit 5 RCIF: EUSART Receive Interrupt Flag bit 1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read) 0 = The EUSART receive buffer is empty bit 4 TXIF: EUSART Transmit Interrupt Flag bit 1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written) 0 = The EUSART transmit buffer is full bit 3 SSPIF: Master Synchronous Serial Port Interrupt Flag bit 1 = The transmission/reception is complete (must be cleared in software) 0 = Waiting to transmit/receive bit 2 CCP1IF: CCP1 Interrupt Flag bit Capture mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused in this mode. bit 1 TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred bit 0 TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow Legend: DS39636D-page 88 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 8-5: PIR2: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 2 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF bit 7 bit 0 bit 7 OSCFIF: Oscillator Fail Interrupt Flag bit 1 = Device oscillator failed, clock input has changed to INTOSC (must be cleared in software) 0 = Device clock operating bit 6 CMIF: Comparator Interrupt Flag bit 1 = Comparator input has changed (must be cleared in software) 0 = Comparator input has not changed bit 5-4 Unimplemented: Read as `0' bit 3 BCLIF: Bus Collision Interrupt Flag bit 1 = A bus collision occurred (must be cleared in software) 0 = No bus collision occurred bit 2 HLVDIF: High/Low-Voltage Detect Interrupt Flag bit 1 = A low-voltage condition occurred (must be cleared in software) 0 = The device voltage is above the High/Low-Voltage Detect trip point bit 1 TMR3IF: TMR3 Overflow Interrupt Flag bit 1 = TMR3 register overflowed (must be cleared in software) 0 = TMR3 register did not overflow bit 0 CCP2IF: CCPx Interrupt Flag bit Capture mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused in this mode. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 89 PIC18F2X1X/4X1X 8.3 PIE Registers The PIE registers contain the individual enable bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt Enable registers (PIE1 and PIE2). When IPEN = 0, the PEIE bit must be set to enable any of these peripheral interrupts. REGISTER 8-6: PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE bit 7 bit 7 bit 0 PSPIE: Parallel Slave Port Read/Write Interrupt Enable bit(1) 1 = Enables the PSP read/write interrupt 0 = Disables the PSP read/write interrupt Note 1: This bit is unimplemented on 28-pin devices and is read as `0'. bit 6 ADIE: A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt bit 5 RCIE: EUSART Receive Interrupt Enable bit 1 = Enables the EUSART receive interrupt 0 = Disables the EUSART receive interrupt bit 4 TXIE: EUSART Transmit Interrupt Enable bit 1 = Enables the EUSART transmit interrupt 0 = Disables the EUSART transmit interrupt bit 3 SSPIE: Master Synchronous Serial Port Interrupt Enable bit 1 = Enables the MSSP interrupt 0 = Disables the MSSP interrupt bit 2 CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit 0 TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt Legend: DS39636D-page 90 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 8-7: PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 OSCFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE bit 7 bit 0 bit 7 OSCFIE: Oscillator Fail Interrupt Enable bit 1 = Enabled 0 = Disabled bit 6 CMIE: Comparator Interrupt Enable bit 1 = Enabled 0 = Disabled bit 5-4 Unimplemented: Read as `0' bit 3 BCLIE: Bus Collision Interrupt Enable bit 1 = Enabled 0 = Disabled bit 2 HLVDIE: High/Low-Voltage Detect Interrupt Enable bit 1 = Enabled 0 = Disabled bit 1 TMR3IE: TMR3 Overflow Interrupt Enable bit 1 = Enabled 0 = Disabled bit 0 CCP2IE: CCP2 Interrupt Enable bit 1 = Enabled 0 = Disabled Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 91 PIC18F2X1X/4X1X 8.4 IPR Registers The IPR registers contain the individual priority bits for the peripheral interrupts. Due to the number of peripheral interrupt sources, there are two Peripheral Interrupt Priority registers (IPR1 and IPR2). Using the priority bits requires that the Interrupt Priority Enable (IPEN) bit be set. REGISTER 8-8: IPR1: PERIPHERAL INTERRUPT PRIORITY REGISTER 1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP bit 7 bit 7 bit 0 PSPIP: Parallel Slave Port Read/Write Interrupt Priority bit(1) 1 = High priority 0 = Low priority Note 1: This bit is unimplemented on 28-pin devices and is read as `0'. bit 6 ADIP: A/D Converter Interrupt Priority bit 1 = High priority 0 = Low priority bit 5 RCIP: EUSART Receive Interrupt Priority bit 1 = High priority 0 = Low priority bit 4 TXIP: EUSART Transmit Interrupt Priority bit 1 = High priority 0 = Low priority bit 3 SSPIP: Master Synchronous Serial Port Interrupt Priority bit 1 = High priority 0 = Low priority bit 2 CCP1IP: CCP1 Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 TMR2IP: TMR2 to PR2 Match Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 TMR1IP: TMR1 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority Legend: DS39636D-page 92 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 8-9: IPR2: PERIPHERAL INTERRUPT PRIORITY REGISTER 2 R/W-1 R/W-1 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP bit 7 bit 0 bit 7 OSCFIP: Oscillator Fail Interrupt Priority bit 1 = High priority 0 = Low priority bit 6 CMIP: Comparator Interrupt Priority bit 1 = High priority 0 = Low priority bit 5-4 Unimplemented: Read as `0' bit 3 BCLIP: Bus Collision Interrupt Priority bit 1 = High priority 0 = Low priority bit 2 HLVDIP: High/Low-Voltage Detect Interrupt Priority bit 1 = High priority 0 = Low priority bit 1 TMR3IP: TMR3 Overflow Interrupt Priority bit 1 = High priority 0 = Low priority bit 0 CCP2IP: CCP2 Interrupt Priority bit 1 = High priority 0 = Low priority Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 93 PIC18F2X1X/4X1X 8.5 RCON Register The RCON register contains flag bits which are used to determine the cause of the last Reset or wake-up from Idle or Sleep modes. RCON also contains the IPEN bit which enables interrupt priorities. REGISTER 8-10: The operation of the SBOREN bit and the Reset flag bits is discussed in more detail in Section 4.1 "RCON Register". RCON REGISTER R/W-0 R/W-1(1) U-0 R/W-1 R-1 R-1 R/W-0(1) R/W-0 IPEN SBOREN -- RI TO PD POR BOR bit 7 bit 0 bit 7 IPEN: Interrupt Priority Enable bit 1 = Enable priority levels on interrupts 0 = Disable priority levels on interrupts (PIC16XXX Compatibility mode) bit 6 SBOREN: Software BOR Enable bit(1) For details of bit operation, see Register 4-1. Note 1: Actual Reset values are determined by device configuration and the nature of the device Reset. See Register 4-1 for additional information. bit 5 Unimplemented: Read as `0' bit 4 RI: RESET Instruction Flag bit For details of bit operation, see Register 4-1. bit 3 TO: Watchdog Time-out Flag bit For details of bit operation, see Register 4-1. bit 2 PD: Power-down Detection Flag bit For details of bit operation, see Register 4-1. bit 1 POR: Power-on Reset Status bit For details of bit operation, see Register 4-1. bit 0 BOR: Brown-out Reset Status bit For details of bit operation, see Register 4-1. Legend: DS39636D-page 94 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 8.6 INTn Pin Interrupts 8.7 External interrupts on the RB0/INT0, RB1/INT1 and RB2/INT2 pins are edge-triggered. If the corresponding INTEDGx bit in the INTCON2 register is set (= 1), the interrupt is triggered by a rising edge; if the bit is clear, the trigger is on the falling edge. When a valid edge appears on the RBx/INTx pin, the corresponding flag bit INTxF is set. This interrupt can be disabled by clearing the corresponding enable bit INTxE. Flag bit INTxF must be cleared in software in the Interrupt Service Routine before re-enabling the interrupt. All external interrupts (INT0, INT1 and INT2) can wakeup the processor from Idle or Sleep modes if bit INTxE was set prior to going into those modes. If the Global Interrupt Enable bit, GIE, is set, the processor will branch to the interrupt vector following wake-up. Interrupt priority for INT1 and INT2 is determined by the value contained in the interrupt priority bits, INT1IP (INTCON3<6>) and INT2IP (INTCON3<7>). There is no priority bit associated with INT0. It is always a high priority interrupt source. TMR0 Interrupt In 8-bit mode (which is the default), an overflow in the TMR0 register (FFh 00h) will set flag bit TMR0IF. In 16-bit mode, an overflow in the TMR0H:TMR0L register pair (FFFFh 0000h) will set TMR0IF. The interrupt can be enabled/disabled by setting/clearing enable bit, TMR0IE (INTCON<5>). Interrupt priority for Timer0 is determined by the value contained in the interrupt priority bit, TMR0IP (INTCON2<2>). See Section 10.0 "Timer0 Module" for further details on the Timer0 module. 8.8 PORTB Interrupt-on-Change An input change on PORTB<7:4> sets flag bit, RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit, RBIE (INTCON<3>). Interrupt priority for PORTB interrupt-on-change is determined by the value contained in the interrupt priority bit, RBIP (INTCON2<0>). 8.9 Context Saving During Interrupts During interrupts, the return PC address is saved on the stack. Additionally, the WREG, STATUS and BSR registers are saved on the fast return stack. If a fast return from interrupt is not used (see Section 5.3 "Data Memory Organization"), the user may need to save the WREG, STATUS and BSR registers on entry to the Interrupt Service Routine. Depending on the user's application, other registers may also need to be saved. Example 8-1 saves and restores the WREG, STATUS and BSR registers during an Interrupt Service Routine. EXAMPLE 8-1: SAVING STATUS, WREG AND BSR REGISTERS IN RAM MOVWF W_TEMP MOVFF STATUS, STATUS_TEMP MOVFF BSR, BSR_TEMP ; ; USER ISR CODE ; MOVFF BSR_TEMP, BSR MOVF W_TEMP, W MOVFF STATUS_TEMP, STATUS (c) 2009 Microchip Technology Inc. ; W_TEMP is in virtual bank ; STATUS_TEMP located anywhere ; BSR_TMEP located anywhere ; Restore BSR ; Restore WREG ; Restore STATUS DS39636D-page 95 PIC18F2X1X/4X1X NOTES: DS39636D-page 96 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 9.0 I/O PORTS Depending on the device selected and features enabled, there are up to five ports available. Some pins of the I/O ports are multiplexed with an alternate function from the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Each port has three registers for its operation. These registers are: * TRIS register (data direction register) * PORT register (reads the levels on the pins of the device) * LAT register (output latch) The Data Latch (LAT register) is useful for read-modifywrite operations on the value that the I/O pins are driving. A simplified model of a generic I/O port, without the interfaces to other peripherals, is shown in Figure 9-1. FIGURE 9-1: GENERIC I/O PORT OPERATION RD LAT Data Bus The RA4 pin is multiplexed with the Timer0 module clock input and one of the comparator outputs to become the RA4/T0CKI/C1OUT pin. Pins RA6 and RA7 are multiplexed with the main oscillator pins; they are enabled as oscillator or I/O pins by the selection of the main oscillator in the Configuration register (see Section 22.1 "Configuration Bits" for details). When they are not used as port pins, RA6 and RA7 and their associated TRIS and LAT bits are read as `0'. The other PORTA pins are multiplexed with analog inputs, the analog VREF+ and VREF- inputs and the comparator voltage reference output. The operation of pins RA3:RA0 and RA5 as A/D converter inputs is selected by clearing or setting the control bits in the ADCON1 register (A/D Control Register 1). Pins RA0 through RA5 may also be used as comparator inputs or outputs by setting the appropriate bits in the CMCON register. To use RA3:RA0 as digital inputs, it is also necessary to turn off the comparators. Q I/O pin(1) CK Data Latch D WR TRIS The Data Latch (LATA) register is also memory mapped. Read-modify-write operations on the LATA register read and write the latched output value for PORTA. Note: D WR LAT or Port Reading the PORTA register reads the status of the pins, whereas writing to it will write to the port latch. Q CK TRIS Latch Input Buffer The RA4/T0CKI/C1OUT pin is a Schmitt Trigger input. All other PORTA pins have TTL input levels and full CMOS output drivers. The TRISA register controls the direction of the PORTA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs. EXAMPLE 9-1: RD TRIS CLRF Q D CLRF ENEN RD Port Note 1: 9.1 On a Power-on Reset, RA5 and RA3:RA0 are configured as analog inputs and read as `0'. RA4 is configured as a digital input. I/O pins have diode protection to VDD and VSS. PORTA, TRISA and LATA Registers PORTA is a 8-bit wide, bidirectional port. The corresponding data direction register is TRISA. Setting a TRISA bit (= 1) will make the corresponding PORTA pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISA bit (= 0) will make the corresponding PORTA pin an output (i.e., put the contents of the output latch on the selected pin). (c) 2009 Microchip Technology Inc. MOVLW MOVWF MOVWF MOVWF MOVLW MOVWF PORTA ; ; ; LATA ; ; ; 07h ; ADCON1 ; 07h ; CMCON ; 0CFh ; ; ; TRISA ; ; INITIALIZING PORTA Initialize PORTA by clearing output data latches Alternate method to clear output data latches Configure A/D for digital inputs Configure comparators for digital input Value used to initialize data direction Set RA<3:0> as inputs RA<5:4> as outputs DS39636D-page 97 PIC18F2X1X/4X1X TABLE 9-1: PORTA I/O SUMMARY Pin RA0/AN0 RA1/AN1 RA2/AN2/ VREF-/CVREF RA3/AN3/VREF+ Function TRIS Setting I/O I/O Type RA0 0 O DIG 1 I TTL PORTA<0> data input; disabled when analog input enabled. AN0 1 I ANA A/D input channel 0 and Comparator C1- input. Default input configuration on POR; does not affect digital output. RA1 0 O DIG LATA<1> data output; not affected by analog input. 1 I TTL PORTA<1> data input; disabled when analog input enabled. AN1 1 I ANA A/D input channel 1 and comparator C2- input. Default input configuration on POR; does not affect digital output. RA2 0 O DIG LATA<2> data output; not affected by analog input. Disabled when CVREF output enabled. 1 I TTL PORTA<2> data input. Disabled when analog functions enabled; disabled when CVREF output enabled. AN2 1 I ANA A/D input channel 2 and comparator C2+ input. Default input configuration on POR; not affected by analog output. VREF- 1 I ANA A/D and comparator voltage reference low input. CVREF x O ANA Comparator voltage reference output. Enabling this feature disables digital I/O. RA3 0 O DIG LATA<3> data output; not affected by analog input. 1 I TTL PORTA<3> data input; disabled when analog input enabled. 1 I ANA A/D input channel 3 and comparator C1+ input. Default input configuration on POR. AN3 RA4/T0CKI/C1OUT RA5/AN4/SS/ HLVDIN/C2OUT OSC2/CLKO/RA6 OSC1/CLKI/RA7 Legend: Description LATA<0> data output; not affected by analog input. VREF+ 1 I ANA A/D and comparator voltage reference high input. RA4 0 O DIG LATA<4> data output. 1 I ST PORTA<4> data input; default configuration on POR. T0CKI 1 I ST Timer0 clock input. C1OUT 0 O DIG Comparator 1 output; takes priority over port data. RA5 0 O DIG LATA<5> data output; not affected by analog input. 1 I TTL PORTA<5> data input; disabled when analog input enabled. A/D input channel 4. Default configuration on POR. AN4 1 I ANA SS 1 I TTL Slave select input for SSP (MSSP module). HLVDIN 1 I ANA High/Low-Voltage Detect external trip point input. C2OUT 0 O DIG Comparator 2 output; takes priority over port data. RA6 0 O DIG LATA<6> data output. Enabled in RCIO, INTIO2 and ECIO modes only. 1 I TTL PORTA<6> data input. Enabled in RCIO, INTIO2 and ECIO modes only. OSC2 x O ANA Main oscillator feedback output connection (XT, HS and LP modes). CLKO x O DIG System cycle clock output (FOSC/4) in RC, INTIO1 and EC Oscillator modes. RA7 0 O DIG LATA<7> data output. Disabled in External Oscillator modes. 1 I TTL PORTA<7> data input. Disabled in External Oscillator modes. OSC1 x I ANA Main oscillator input connection. CLKI x I ANA Main clock input connection. DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output; x = Don't care (TRIS bit does not affect port direction or is overridden for this option). DS39636D-page 98 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 9-2: Name PORTA SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RA7(1) RA6(1) RA5 RA4 RA3 RA2 RA1 RA0 (1) LATA6(1) PORTA Data Latch Register (Read and Write to Data Latch) LATA LATA7 TRISA TRISA7(1) TRISA6(1) PORTA Data Direction Control Register Reset Values on page 54 54 54 ADCON1 -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 53 CMCON C2OUT C1OUT C2INV C1INV CIS CM2 CM1 CM0 53 CVRCON CVREN CVROE CVRR CVRSS CVR3 CVR2 CVR1 CVR0 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by PORTA. Note 1: RA7:RA6 and their associated latch and data direction bits are enabled as I/O pins based on oscillator configuration; otherwise, they are read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 99 PIC18F2X1X/4X1X 9.2 PORTB, TRISB and LATB Registers PORTB is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISB. Setting a TRISB bit (= 1) will make the corresponding PORTB pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISB bit (= 0) will make the corresponding PORTB pin an output (i.e., put the contents of the output latch on the selected pin). The Data Latch register (LATB) is also memory mapped. Read-modify-write operations on the LATB register read and write the latched output value for PORTB. EXAMPLE 9-2: CLRF CLRF MOVLW MOVWF MOVLW MOVWF PORTB ; ; ; LATB ; ; ; 0Fh ; ADCON1 ; ; ; 0CFh ; ; ; TRISB ; ; ; INITIALIZING PORTB Initialize PORTB by clearing output data latches Alternate method to clear output data latches Set RB<4:0> as digital I/O pins (required if config bit PBADEN is set) Value used to initialize data direction Set RB<3:0> as inputs RB<5:4> as outputs RB<7:6> as inputs Four of the PORTB pins (RB7:RB4) have an interrupton-change feature. Only pins configured as inputs can cause this interrupt to occur (i.e., any RB7:RB4 pin configured as an output is excluded from the interrupton-change comparison). The input pins (of RB7:RB4) are compared with the old value latched on the last read of PORTB. The "mismatch" outputs of RB7:RB4 are ORed together to generate the RB Port Change Interrupt with Flag bit, RBIF (INTCON<0>). This interrupt can wake the device from the Sleep mode, or any of the Idle modes. The user, in the Interrupt Service Routine, can clear the interrupt in the following manner: a) b) Any read or write of PORTB (except with the MOVFF (ANY), PORTB instruction). Clear flag bit RBIF. A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition and allow flag bit RBIF to be cleared. The interrupt-on-change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt-on-change feature. Polling of PORTB is not recommended while using the interrupt-on-change feature. RB3 can be configured by the Configuration bit, CCP2MX, as the alternate peripheral pin for the CCP2 module (CCP2MX = 0). Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit, RBPU (INTCON2<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. Note: On a Power-on Reset, RB4:RB0 are configured as analog inputs by default and read as `0'; RB7:RB5 are configured as digital inputs. By programming the Configuration bit, PBADEN, RB4:RB0 will alternatively be configured as digital inputs on POR. DS39636D-page 100 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 9-3: Pin RB0/INT0/FLT0/ AN12 RB1/INT1/AN10 RB2/INT2/AN8 RB3/AN9/CCP2 PORTB I/O SUMMARY Function TRIS Setting I/O I/O Type RB0 0 O DIG LATB<0> data output; not affected by analog input. 1 I TTL PORTB<0> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) External interrupt 0 input. INT0 1 I ST FLT0 1 I ST AN12 1 I ANA A/D input channel 12.(1) RB1 0 O DIG LATB<1> data output; not affected by analog input. 1 I TTL PORTB<1> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) INT1 1 I ST 1 I ANA A/D input channel 10.(1) RB2 0 O DIG LATB<2> data output; not affected by analog input. 1 I TTL PORTB<2> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) RB6/KBI2/PGC RB7/KBI3/PGD Legend: Note 1: 2: 3: External interrupt 1 input. INT2 1 I ST AN8 1 I ANA A/D input channel 8.(1) RB3 0 O DIG LATB<3> data output; not affected by analog input. 1 I TTL PORTB<3> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) 1 I ANA A/D input channel 9.(1) 0 O DIG CCP2 compare and PWM output. 1 I ST CCP2 capture input 0 O DIG LATB<4> data output; not affected by analog input. 1 I TTL PORTB<4> data input; weak pull-up when RBPU bit is cleared. Disabled when analog input enabled.(1) KBI0 1 I TTL Interrupt on pin change. AN11 1 I ANA A/D input channel 11.(1) RB5 0 O DIG LATB<5> data output. 1 I TTL PORTB<5> data input; weak pull-up when RBPU bit is cleared. CCP2 RB5/KBI1/PGM Enhanced PWM Fault input (ECCP1 module); enabled in software. AN10 AN9 RB4/KBI0/AN11 Description (2) RB4 External interrupt 2 input. KBI1 1 I TTL Interrupt on pin change. PGM x I ST Single-Supply Programming mode entry (ICSPTM). Enabled by LVP Configuration bit; all other pin functions disabled. RB6 0 O DIG LATB<6> data output. 1 I TTL PORTB<6> data input; weak pull-up when RBPU bit is cleared. KBI2 1 I TTL Interrupt on pin change. PGC x I ST Serial execution (ICSP) clock input for ICSP and ICD operation.(3) RB7 0 O DIG LATB<7> data output. 1 I TTL PORTB<7> data input; weak pull-up when RBPU bit is cleared. KBI3 1 I TTL Interrupt on pin change. PGD x O DIG Serial execution data output for ICSP and ICD operation.(3) x I ST Serial execution data input for ICSP and ICD operation.(3) DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output; x = Don't care (TRIS bit does not affect port direction or is overridden for this option). Configuration on POR is determined by the PBADEN Configuration bit. Pins are configured as analog inputs by default when PBADEN is set and digital inputs when PBADEN is cleared. Alternate assignment for CCP2 when the CCP2MX Configuration bit is `0'. Default assignment is RC1. All other pin functions are disabled when ICSP or ICD are enabled. (c) 2009 Microchip Technology Inc. DS39636D-page 101 PIC18F2X1X/4X1X TABLE 9-4: Name PORTB SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 54 LATB PORTB Data Latch Register (Read and Write to Data Latch) 54 TRISB PORTB Data Direction Control Register 54 INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE INTEDG0 INTEDG1 INTEDG2 RBIE TMR0IF INT0IF RBIF 51 -- TMR0IP -- RBIP 51 INTCON2 RBPU INTCON3 INT2IP INT1IP -- INT2IE INT1IE -- INT2IF INT1IF 51 ADCON1 -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by PORTB. DS39636D-page 102 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 9.3 PORTC, TRISC and LATC Registers PORTC is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISC. Setting a TRISC bit (= 1) will make the corresponding PORTC pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISC bit (= 0) will make the corresponding PORTC pin an output (i.e., put the contents of the output latch on the selected pin). The Data Latch register (LATC) is also memory mapped. Read-modify-write operations on the LATC register read and write the latched output value for PORTC. PORTC is multiplexed with several peripheral functions (Table 9-5). The pins have Schmitt Trigger input buffers. RC1 is normally configured by Configuration bit, CCP2MX, as the default peripheral pin of the CCP2 module (default/erased state, CCP2MX = 1). The contents of the TRISC register are affected by peripheral overrides. Reading TRISC always returns the current contents, even though a peripheral device may be overriding one or more of the pins. EXAMPLE 9-3: CLRF PORTC CLRF LATC MOVLW 0CFh MOVWF TRISC INITIALIZING PORTC ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTC by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RC<3:0> as inputs RC<5:4> as outputs RC<7:6> as inputs When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTC pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. The user should refer to the corresponding peripheral section for additional information. Note: On a Power-on Reset, these pins are configured as digital inputs. (c) 2009 Microchip Technology Inc. DS39636D-page 103 PIC18F2X1X/4X1X TABLE 9-5: Pin PORTC I/O SUMMARY Function TRIS Setting I/O I/O Type RC0 0 O DIG RC0/T1OSO/ T13CKI RC1/T1OSI/CCP2 RC2/CCP1/P1A 1 I ST x O ANA T13CKI 1 I ST Timer1/Timer3 counter input. RC1 0 O DIG LATC<1> data output. 1 I ST T1OSI x I ANA Timer1 oscillator input; enabled when Timer1 oscillator enabled. Disables digital I/O. CCP2(1) 0 O DIG CCP2 compare and PWM output; takes priority over port data. 1 I ST CCP2 capture input. 0 O DIG LATC<2> data output. 1 I ST PORTC<2> data input. 0 O DIG ECCP1 compare or PWM output; takes priority over port data. 1 I ST ECCP1 capture input. P1A(2) 0 O DIG ECCP1 Enhanced PWM output, channel A. May be configured for tri-state during Enhanced PWM shutdown events. Takes priority over port data. RC3 0 O DIG LATC<3> data output. 1 I ST PORTC<3> data input. 0 O DIG SPI clock output (MSSP module); takes priority over port data. RC2 SCK SCL RC4/SDI/SDA RC5/SDO RC7/RX/DT Legend: Note 1: 2: RC4 PORTC<0> data input. Timer1 oscillator output; enabled when Timer1 oscillator enabled. Disables digital I/O. PORTC<1> data input. 1 I ST SPI clock input (MSSP module). 0 O DIG I2CTM clock output (MSSP module); takes priority over port data. 1 I I2C/SMB 0 O DIG I2C clock input (MSSP module); input type depends on module setting. LATC<4> data output. 1 I ST PORTC<4> data input. SDI 1 I ST SPI data input (MSSP module). SDA 1 O DIG I2C data output (MSSP module); takes priority over port data. 1 I 0 O DIG 1 I ST PORTC<5> data input. SDO 0 O DIG SPI data output (MSSP module); takes priority over port data. RC6 0 O DIG LATC<6> data output. RC5 RC6/TX/CK LATC<0> data output. T1OSO CCP1 RC3/SCK/SCL Description I2C/SMB I2C data input (MSSP module); input type depends on module setting. LATC<5> data output. 1 I ST PORTC<6> data input. TX 1 O DIG Asynchronous serial transmit data output (USART module); takes priority over port data. User must configure as output. CK 1 O DIG Synchronous serial clock output (USART module); takes priority over port data. 1 I ST Synchronous serial clock input (USART module). 0 O DIG LATC<7> data output. 1 I ST PORTC<7> data input. RX 1 I ST Asynchronous serial receive data input (USART module). DT 1 O DIG Synchronous serial data output (USART module); takes priority over port data. 1 I ST Synchronous serial data input (USART module). User must configure as an input. RC7 DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output; I2C/SMB = I2C/SMBus input buffer; x = Don't care (TRIS bit does not affect port direction or is overridden for this option). Default assignment for CCP2 when the CCP2MX Configuration bit is set. Alternate assignment is RB3. Enhanced PWM output is available only on PIC18F4410/4415/4510/4515/4610 devices. DS39636D-page 104 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 9-6: Name PORTC SUMMARY OF REGISTERS ASSOCIATED WITH PORTC Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 54 LATC PORTC Data Latch Register (Read and Write to Data Latch) 54 TRISC PORTC Data Direction Control Register 54 (c) 2009 Microchip Technology Inc. DS39636D-page 105 PIC18F2X1X/4X1X 9.4 Note: PORTD, TRISD and LATD Registers PORTD is only available on 40/44-pin devices. PORTD is an 8-bit wide, bidirectional port. The corresponding data direction register is TRISD. Setting a TRISD bit (= 1) will make the corresponding PORTD pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISD bit (= 0) will make the corresponding PORTD pin an output (i.e., put the contents of the output latch on the selected pin). The Data Latch register (LATD) is also memory mapped. Read-modify-write operations on the LATD register read and write the latched output value for PORTD. All pins on PORTD are implemented with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Three of the PORTD pins are multiplexed with outputs P1B, P1C and P1D of the enhanced CCP module. The operation of these additional PWM output pins is covered in greater detail in Section 15.0 "Enhanced Capture/Compare/PWM (ECCP) Module". Note: PORTD can also be configured as an 8-bit wide microprocessor port (Parallel Slave Port) by setting control bit, PSPMODE (TRISE<4>). In this mode, the input buffers are TTL. See Section 9.6 "Parallel Slave Port" for additional information on the Parallel Slave Port (PSP). Note: When the enhanced PWM mode is used with either dual or quad outputs, the PSP functions of PORTD are automatically disabled. EXAMPLE 9-4: CLRF PORTD CLRF LATD MOVLW 0CFh MOVWF TRISD INITIALIZING PORTD ; ; ; ; ; ; ; ; ; ; ; ; Initialize PORTD by clearing output data latches Alternate method to clear output data latches Value used to initialize data direction Set RD<3:0> as inputs RD<5:4> as outputs RD<7:6> as inputs On a Power-on Reset, these pins are configured as digital inputs. DS39636D-page 106 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 9-7: Pin RD0/PSP0 PORTD I/O SUMMARY Function TRIS Setting I/O I/O Type RD0 0 O DIG 1 I ST PORTD<0> data input. x O DIG PSP read data output (LATD<0>); takes priority over port data. x I TTL PSP write data input. 0 O DIG LATD<1> data output. 1 I ST PORTD<1> data input. x O DIG PSP read data output (LATD<1>); takes priority over port data. x I TTL PSP write data input. LATD<2> data output. PSP0 RD1/PSP1 RD1 PSP1 RD2/PSP2 RD2 PSP2 RD3/PSP3 RD3 PSP3 RD4/PSP4 RD4 PSP4 RD5/PSP5/P1B RD5 RD7/PSP7/P1D 0 O DIG 1 I ST PORTD<2> data input. x O DIG PSP read data output (LATD<2>); takes priority over port data. x I TTL PSP write data input. 0 O DIG LATD<3> data output. 1 I ST PORTD<3> data input. x O DIG PSP read data output (LATD<3>); takes priority over port data. x I TTL PSP write data input. LATD<4> data output. 0 O DIG 1 I ST PORTD<4> data input. x O DIG PSP read data output (LATD<4>); takes priority over port data. x I TTL PSP write data input. LATD<5> data output. 0 O DIG I ST PORTD<5> data input. x O DIG PSP read data output (LATD<5>); takes priority over port data. x I TTL PSP write data input. P1B 0 O DIG ECCP1 Enhanced PWM output, channel B; takes priority over port and PSP data. May be configured for tri-state during Enhanced PWM shutdown events. RD6 0 O DIG LATD<6> data output. 1 I ST PORTD<6> data input. PSP6 x O DIG PSP read data output (LATD<6>); takes priority over port data. x I TTL PSP write data input. P1C 0 O DIG ECCP1 Enhanced PWM output, channel C; takes priority over port and PSP data. May be configured for tri-state during Enhanced PWM shutdown events. RD7 0 O DIG LATD<7> data output. 1 I ST PORTD<7> data input. PSP read data output (LATD<7>); takes priority over port data. PSP7 P1D Legend: LATD<0> data output. 1 PSP5 RD6/PSP6/P1C Description x O DIG x I TTL PSP write data input. 0 O DIG ECCP1 Enhanced PWM output, channel D; takes priority over port and PSP data. May be configured for tri-state during Enhanced PWM shutdown events. DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; x = Don't care (TRIS bit does not affect port direction or is overridden for this option). (c) 2009 Microchip Technology Inc. DS39636D-page 107 PIC18F2X1X/4X1X TABLE 9-8: Name PORTD SUMMARY OF REGISTERS ASSOCIATED WITH PORTD Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 54 LATD PORTD Data Latch Register (Read and Write to Data Latch) 54 TRISD PORTD Data Direction Control Register 54 TRISE CCP1CON IBF OBF IBOV PSPMODE -- TRISE2 TRISE1 TRISE0 54 P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by PORTD. DS39636D-page 108 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 9.5 PORTE, TRISE and LATE Registers Depending on the particular PIC18F2X1X/4X1X device selected, PORTE is implemented in two different ways. For 40/44-pin devices, PORTE is a 4-bit wide port. Three pins (RE0/RD/AN5, RE1/WR/AN6 and RE2/CS/ AN7) are individually configurable as inputs or outputs. These pins have Schmitt Trigger input buffers. When selected as an analog input, these pins will read as `0's. The corresponding data direction register is TRISE. Setting a TRISE bit (= 1) will make the corresponding PORTE pin an input (i.e., put the corresponding output driver in a high-impedance mode). Clearing a TRISE bit (= 0) will make the corresponding PORTE pin an output (i.e., put the contents of the output latch on the selected pin). TRISE controls the direction of the RE pins, even when they are being used as analog inputs. The user must make sure to keep the pins configured as inputs when using them as analog inputs. Note: On a Power-on Reset, RE2:RE0 are configured as analog inputs. The upper four bits of the TRISE register also control the operation of the Parallel Slave Port. Their operation is explained in Register 9-1. The Data Latch register (LATE) is also memory mapped. Read-modify-write operations on the LATE register, read and write the latched output value for PORTE. (c) 2009 Microchip Technology Inc. The fourth pin of PORTE (MCLR/VPP/RE3) is an input only pin. Its operation is controlled by the MCLRE Configuration bit. When selected as a port pin (MCLRE = 0), it functions as a digital input only pin; as such, it does not have TRIS or LAT bits associated with its operation. Otherwise, it functions as the device's Master Clear input. In either configuration, RE3 also functions as the programming voltage input during programming. Note: On a Power-on Reset, RE3 is enabled as a digital input only if Master Clear functionality is disabled. EXAMPLE 9-5: CLRF CLRF MOVLW MOVWF MOVLW MOVWF 9.5.1 PORTE ; ; ; LATE ; ; ; 0Ah ; ADCON1 ; 03h ; ; ; TRISE ; ; ; INITIALIZING PORTE Initialize PORTE by clearing output data latches Alternate method to clear output data latches Configure A/D for digital inputs Value used to initialize data direction Set RE<0> as inputs RE<1> as outputs RE<2> as inputs PORTE IN 28-PIN DEVICES For 28-pin devices, PORTE is only available when Master Clear functionality is disabled (MCLRE = 0). In these cases, PORTE is a single bit, input only port comprised of RE3 only. The pin operates as previously described. DS39636D-page 109 PIC18F2X1X/4X1X REGISTER 9-1: TRISE REGISTER (40/44-PIN DEVICES ONLY) R-0 R-0 R/W-0 R/W-0 U-0 R/W-1 R/W-1 R/W-1 IBF OBF IBOV PSPMODE -- TRISE2 TRISE1 TRISE0 bit 7 bit 0 bit 7 IBF: Input Buffer Full Status bit 1 = A word has been received and waiting to be read by the CPU 0 = No word has been received bit 6 OBF: Output Buffer Full Status bit 1 = The output buffer still holds a previously written word 0 = The output buffer has been read bit 5 IBOV: Input Buffer Overflow Detect bit (in Microprocessor mode) 1 = A write occurred when a previously input word has not been read (must be cleared in software) 0 = No overflow occurred bit 4 PSPMODE: Parallel Slave Port Mode Select bit 1 = Parallel Slave Port mode 0 = General purpose I/O mode bit 3 Unimplemented: Read as `0' bit 2 TRISE2: RE2 Direction Control bit 1 = Input 0 = Output bit 1 TRISE1: RE1 Direction Control bit 1 = Input 0 = Output bit 0 TRISE0: RE0 Direction Control bit 1 = Input 0 = Output Legend: DS39636D-page 110 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 9-9: PORTE I/O SUMMARY Pin Function TRIS Setting I/O I/O Type RE0 0 O DIG LATE<0> data output; not affected by analog input. 1 I ST PORTE<0> data input; disabled when analog input enabled. RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 MCLR/VPP/RE3(1) Legend: Note 1: 2: RD 1 I TTL PSP read enable input (PSP enabled). AN5 1 I ANA A/D input channel 5; default input configuration on POR. RE1 0 O DIG LATE<1> data output; not affected by analog input. 1 I ST PORTE<1> data input; disabled when analog input enabled. WR 1 I TTL PSP write enable input (PSP enabled). AN6 1 I ANA A/D input channel 6; default input configuration on POR. RE2 0 O DIG LATE<2> data output; not affected by analog input. 1 I ST PORTE<2> data input; disabled when analog input enabled. CS 1 I TTL PSP write enable input (PSP enabled). AN7 1 I ANA A/D input channel 7; default input configuration on POR. MCLR -- I ST External Master Clear input; enabled when MCLRE Configuration bit is set. VPP -- I ANA High-voltage detection; used for ICSPTM mode entry detection. Always available, regardless of pin mode. RE3 --(2) I ST PORTE<3> data input; enabled when MCLRE Configuration bit is clear. DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output; x = Don't care (TRIS bit does not affect port direction or is overridden for this option). RE3 is available on both 28-pin and 40/44-pin devices. All other PORTE pins are only implemented on 40/44-pin devices. RE3 does not have a corresponding TRIS bit to control data direction. TABLE 9-10: Name Description SUMMARY OF REGISTERS ASSOCIATED WITH PORTE Bit 2 Bit 1 Bit 0 RE2 RE1 RE0 Reset Values on page Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 PORTE -- -- -- -- RE3(1,2) LATE(2) -- -- -- -- -- TRISE IBF OBF IBOV PSPMODE -- TRISE2 TRISE1 TRISE0 54 ADCON1 -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 53 LATE Data Output Register 54 54 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by PORTE. Note 1: Implemented only when Master Clear functionality is disabled (MCLRE Configuration bit = 0). 2: RE3 is the only PORTE bit implemented on both 28-pin and 40/44-pin devices. All other bits are implemented only when PORTE is implemented (i.e., 40/44-pin devices). (c) 2009 Microchip Technology Inc. DS39636D-page 111 PIC18F2X1X/4X1X 9.6 Note: Parallel Slave Port The Parallel Slave Port is only available on 40/44-pin devices. In addition to its function as a general I/O port, PORTD can also operate as an 8-bit wide Parallel Slave Port (PSP) or microprocessor port. PSP operation is controlled by the 4 upper bits of the TRISE register (Register 9-1). Setting control bit, PSPMODE (TRISE<4>), enables PSP operation as long as the enhanced CCP module is not operating in dual output or quad output PWM mode. In Slave mode, the port is asynchronously readable and writable by the external world. The PSP can directly interface to an 8-bit microprocessor data bus. The external microprocessor can read or write the PORTD latch as an 8-bit latch. Setting the control bit PSPMODE enables the PORTE I/O pins to become control inputs for the microprocessor port. When set, port pin RE0 is the RD input, RE1 is the WR input and RE2 is the CS (Chip Select) input. For this functionality, the corresponding data direction bits of the TRISE register (TRISE<2:0>) must be configured as inputs (set). The A/D port control bits, PFCG3:PFCG0 (ADCON1<3:0>), must also be set to a value in the range of `1010' through `1111'. The timing for the control signals in Write and Read modes is shown in Figure 9-3 and Figure 9-4, respectively. FIGURE 9-2: One bit of PORTD Data Bus WR LATD or WR PORTD Q RDx pin CK Data Latch RD PORTD TTL D ENEN RD LATD Set Interrupt Flag PSPIF (PIR1<7>) PORTE Pins Read A read from the PSP occurs when both the CS and RD lines are first detected low. The data in PORTD is read out and the OBF bit is clear. If the user writes new data to PORTD to set OBF, the data is immediately read out; however, the OBF bit is not set. DS39636D-page 112 D Q A write to the PSP occurs when both the CS and WR lines are first detected low and ends when either are detected high. The PSPIF and IBF flag bits are both set when the write ends. When either the CS or RD lines are detected high, the PORTD pins return to the input state and the PSPIF bit is set. User applications should wait for PSPIF to be set before servicing the PSP; when this happens, the IBF and OBF bits can be polled and the appropriate action taken. PORTD AND PORTE BLOCK DIAGRAM (PARALLEL SLAVE PORT) TTL RD Chip Select TTL CS Write Note: TTL WR I/O pins have diode protection to VDD and VSS. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 9-3: PARALLEL SLAVE PORT WRITE WAVEFORMS Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q4 Q1 Q2 Q3 Q4 CS WR RD PORTD<7:0> IBF OBF PSPIF FIGURE 9-4: PARALLEL SLAVE PORT READ WAVEFORMS Q1 Q2 Q3 Q4 Q1 Q2 Q3 CS WR RD PORTD<7:0> IBF OBF PSPIF TABLE 9-11: REGISTERS ASSOCIATED WITH PARALLEL SLAVE PORT Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page PORTD RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 54 LATD PORTD Data Latch Register (Read and Write to Data Latch) 54 TRISD PORTD Data Direction Control Register 54 PORTE -- -- -- -- RE3 LATE -- -- -- -- -- IBF OBF IBOV PSPMODE -- TRISE2 TRISE1 TRISE0 54 TMR0IF INT0IE RBIE TMR0IF INT0IF RBIF 51 TRISE RE2 RE1 RE0 LATE Data Output bits 54 54 INTCON GIE/GIEH PEIE/GIEL PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 53 ADCON1 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by the Parallel Slave Port. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 113 PIC18F2X1X/4X1X NOTES: DS39636D-page 114 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 10.0 TIMER0 MODULE The Timer0 module incorporates the following features: * Software selectable operation as a timer or counter in both 8-Bit or 16-Bit modes * Readable and writable registers * Dedicated 8-bit, software programmable prescaler * Selectable clock source (internal or external) * Edge select for external clock * Interrupt-on-overflow REGISTER 10-1: The T0CON register (Register 10-1) controls all aspects of the module's operation, including the prescale selection. It is both readable and writable. A simplified block diagram of the Timer0 module in 8-Bit mode is shown in Figure 10-1. Figure 10-2 shows a simplified block diagram of the Timer0 module in 16-Bit mode. T0CON: TIMER0 CONTROL REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 bit 7 bit 0 bit 7 TMR0ON: Timer0 On/Off Control bit 1 = Enables Timer0 0 = Stops Timer0 bit 6 T08BIT: Timer0 8-bit/16-bit Control bit 1 = Timer0 is configured as an 8-bit timer/counter 0 = Timer0 is configured as a 16-bit timer/counter bit 5 T0CS: Timer0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKO) bit 4 T0SE: Timer0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin bit 3 PSA: Timer0 Prescaler Assignment bit 1 = TImer0 prescaler is NOT assigned. Timer0 clock input bypasses prescaler. 0 = Timer0 prescaler is assigned. Timer0 clock input comes from prescaler output. bit 2-0 T0PS2:T0PS0: Timer0 Prescaler Select bits 111 = 1:256 Prescale value 110 = 1:128 Prescale value 101 = 1:64 Prescale value 100 = 1:32 Prescale value 011 = 1:16 Prescale value 010 = 1:8 Prescale value 001 = 1:4 Prescale value 000 = 1:2 Prescale value Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 115 PIC18F2X1X/4X1X 10.1 Timer0 Operation Timer0 can operate as either a timer or a counter; the mode is selected with the T0CS bit (T0CON<5>). In Timer mode (T0CS = 0), the module increments on every clock by default unless a different prescaler value is selected (see Section 10.3 "Prescaler"). If the TMR0 register is written to, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. The Counter mode is selected by setting the T0CS bit (= 1). In this mode, Timer0 increments either on every rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit, T0SE (T0CON<4>); clearing this bit selects the rising edge. Restrictions on the external clock input are discussed below. An external clock source can be used to drive Timer0; however, it must meet certain requirements to ensure that the external clock can be synchronized with the FIGURE 10-1: internal phase clock (TOSC). There is a delay between synchronization and the onset of incrementing the timer/counter. 10.2 Timer0 Reads and Writes in 16-Bit Mode TMR0H is not the actual high byte of Timer0 in 16-Bit mode; it is actually a buffered version of the real high byte of Timer0 which is not directly readable nor writable (refer to Figure 10-2). TMR0H is updated with the contents of the high byte of Timer0 during a read of TMR0L. This provides the ability to read all 16 bits of Timer0 without having to verify that the read of the high and low byte were valid, due to a rollover between successive reads of the high and low byte. Similarly, a write to the high byte of Timer0 must also take place through the TMR0H Buffer register. The high byte is updated with the contents of TMR0H when a write occurs to TMR0L. This allows all 16 bits of Timer0 to be updated at once. TIMER0 BLOCK DIAGRAM (8-BIT MODE) FOSC/4 0 1 1 Programmable Prescaler T0CKI pin T0SE T0CS 0 Sync with Internal Clocks (2 TCY Delay) 8 3 T0PS2:T0PS0 8 PSA Note: Set TMR0IF on Overflow TMR0L Internal Data Bus Upon Reset, Timer0 is enabled in 8-Bit mode with clock input from T0CKI max. prescale. FIGURE 10-2: TIMER0 BLOCK DIAGRAM (16-BIT MODE) FOSC/4 0 0 1 T0CKI pin T0SE T0CS Programmable Prescaler 1 Sync with Internal Clocks TMR0 High Byte TMR0L 8 Set TMR0IF on Overflow (2 TCY Delay) 3 Read TMR0L T0PS2:T0PS0 Write TMR0L PSA 8 8 TMR0H 8 8 Internal Data Bus Note: Upon Reset, Timer0 is enabled in 8-Bit mode with clock input from T0CKI max. prescale. DS39636D-page 116 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 10.3 Prescaler 10.3.1 An 8-bit counter is available as a prescaler for the Timer0 module. The prescaler is not directly readable or writable; its value is set by the PSA and T0PS2:T0PS0 bits (T0CON<3:0>), which determine the prescaler assignment and prescale ratio. Clearing the PSA bit assigns the prescaler to the Timer0 module. When it is assigned, prescale values from 1:2 through 1:256 in power-of-2 increments are selectable. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g., CLRF TMR0, MOVWF TMR0, BSF TMR0, etc.) clear the prescaler count. Note: Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count but will not change the prescaler assignment. TABLE 10-1: Name SWITCHING PRESCALER ASSIGNMENT The prescaler assignment is fully under software control and can be changed "on-the-fly" during program execution. 10.4 Timer0 Interrupt The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h in 8-Bit mode, or from FFFFh to 0000h in 16-Bit mode. This overflow sets the TMR0IF flag bit. The interrupt can be masked by clearing the TMR0IE bit (INTCON<5>). Before re-enabling the interrupt, the TMR0IF bit must be cleared in software by the Interrupt Service Routine. Since Timer0 is shut down in Sleep mode, the TMR0 interrupt cannot awaken the processor from Sleep. REGISTERS ASSOCIATED WITH TIMER0 Bit 7 Bit 6 Bit 5 TMR0L Timer0 Register, Low Byte TMR0H Timer0 Register, High Byte INTCON GIE/GIEH PEIE/GIEL TMR0IE T0CON TMR0ON T08BIT TRISA RA7(1) RA6(1) Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page 52 52 INT0IE RBIE TMR0IF INT0IF RBIF 51 T0CS T0SE PSA T0PS2 T0PS1 T0PS0 52 RA5 RA4 RA3 RA2 RA1 RA0 54 Legend: Shaded cells are not used by Timer0. Note 1: PORTA<7:6> and their direction bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 117 PIC18F2X1X/4X1X NOTES: DS39636D-page 118 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 11.0 TIMER1 MODULE The Timer1 timer/counter module incorporates these features: * Software selectable operation as a 16-bit timer or counter * Readable and writable 8-bit registers (TMR1H and TMR1L) * Selectable clock source (internal or external) with device clock or Timer1 oscillator internal options * Interrupt-on-overflow * Reset on CCP special event trigger * Device clock status flag (T1RUN) REGISTER 11-1: A simplified block diagram of the Timer1 module is shown in Figure 11-1. A block diagram of the module's operation in Read/Write mode is shown in Figure 11-2. The module incorporates its own low-power oscillator to provide an additional clocking option. The Timer1 oscillator can also be used as a low-power clock source for the microcontroller in power-managed operation. Timer1 can also be used to provide Real-Time Clock (RTC) functionality to applications with only a minimal addition of external components and code overhead. Timer1 is controlled through the T1CON Control register (Register 11-1). It also contains the Timer1 Oscillator Enable bit (T1OSCEN). Timer1 can be enabled or disabled by setting or clearing control bit, TMR1ON (T1CON<0>). T1CON: TIMER1 CONTROL REGISTER R/W-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON bit 7 bit 0 bit 7 RD16: 16-bit Read/Write Mode Enable bit 1 = Enables register read/write of TImer1 in one 16-bit operation 0 = Enables register read/write of Timer1 in two 8-bit operations bit 6 T1RUN: Timer1 System Clock Status bit 1 = Device clock is derived from Timer1 oscillator 0 = Device clock is derived from another source bit 5-4 T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3 T1OSCEN: Timer1 Oscillator Enable bit 1 = Timer1 oscillator is enabled 0 = Timer1 oscillator is shut off The oscillator inverter and feedback resistor are turned off to eliminate power drain. bit 2 T1SYNC: Timer1 External Clock Input Synchronization Select bit When TMR1CS = 1: 1 = Do not synchronize external clock input 0 = Synchronize external clock input When TMR1CS = 0: This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. bit 1 TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin RC0/T1OSO/T13CKI (on the rising edge) 0 = Internal clock (FOSC/4) bit 0 TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 Legend: R = Readable bit -n = Value at POR (c) 2009 Microchip Technology Inc. W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown DS39636D-page 119 PIC18F2X1X/4X1X 11.1 Timer1 Operation cycle (Fosc/4). When the bit is set, Timer1 increments on every rising edge of the Timer1 external clock input or the Timer1 oscillator, if enabled. Timer1 can operate in one of these modes: * Timer * Synchronous Counter * Asynchronous Counter When Timer1 is enabled, the RC1/T1OSI and RC0/ T1OSO/T13CKI pins become inputs. This means the values of TRISC<1:0> are ignored and the pins are read as `0'. The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). When TMR3CS is cleared (= 0), Timer1 increments on every internal instruction FIGURE 11-1: TIMER1 BLOCK DIAGRAM Timer1 Oscillator Timer1 Clock Input 1 On/Off T1OSO/T13CKI 1 FOSC/4 Internal Clock T1OSI Synchronize Prescaler 1, 2, 4, 8 0 Detect 0 2 T1OSCEN(1) Sleep Input TMR1CS Timer1 On/Off T1CKPS1:T1CKPS0 T1SYNC TMR1ON Clear TMR1 (CCP Special Event Trigger) Set TMR1IF on Overflow TMR1 High Byte TMR1L Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain. FIGURE 11-2: TIMER1 BLOCK DIAGRAM (16-BIT READ/WRITE MODE) Timer1 Oscillator Timer1 Clock Input T1OSO/T13CKI 1 FOSC/4 Internal Clock T1OSI 1 Synchronize Prescaler 1, 2, 4, 8 0 Detect 0 2 T1OSCEN(1) Sleep Input TMR1CS Timer1 On/Off T1CKPS1:T1CKPS0 T1SYNC TMR1ON Clear TMR1 (CCP Special Event Trigger) TMR1 High Byte TMR1L 8 Set TMR1IF on Overflow Read TMR1L Write TMR1L 8 8 TMR1H 8 8 Internal Data Bus Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain. DS39636D-page 120 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 11.2 Timer1 16-Bit Read/Write Mode Timer1 can be configured for 16-bit reads and writes (see Figure 11-2). When the RD16 control bit (T1CON<7>) is set, the address for TMR1H is mapped to a buffer register for the high byte of Timer1. A read from TMR1L will load the contents of the high byte of Timer1 into the Timer1 high byte buffer. This provides the user with the ability to accurately read all 16 bits of Timer1 without having to determine whether a read of the high byte, followed by a read of the low byte, has become invalid due to a rollover between reads. TABLE 11-1: Osc Type Freq C1 C2 LP 32 kHz 27 pF(1) 27 pF(1) Note 1: Microchip suggests these values as a starting point in validating the oscillator circuit. 2: Higher capacitance increases the stability of the oscillator but also increases the start-up time. A write to the high byte of Timer1 must also take place through the TMR1H Buffer register. The Timer1 high byte is updated with the contents of TMR1H when a write occurs to TMR1L. This allows a user to write all 16 bits to both the high and low bytes of Timer1 at once. The high byte of Timer1 is not directly readable or writable in this mode. All reads and writes must take place through the Timer1 High Byte Buffer register. Writes to TMR1H do not clear the Timer1 prescaler. The prescaler is only cleared on writes to TMR1L. 11.3 Timer1 Oscillator An on-chip crystal oscillator circuit is incorporated between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting the Timer1 Oscillator Enable bit, T1OSCEN (T1CON<3>). The oscillator is a low-power circuit rated for 32 kHz crystals. It will continue to run during all power-managed modes. The circuit for a typical LP oscillator is shown in Figure 11-3. Table 11-1 shows the capacitor selection for the Timer1 oscillator. The user must provide a software time delay to ensure proper start-up of the Timer1 oscillator. FIGURE 11-3: EXTERNAL COMPONENTS FOR THE TIMER1 LP OSCILLATOR C1 27 pF PIC18FXXXX T1OSI XTAL 32.768 kHz T1OSO C2 27 pF Note: See the Notes with Table 11-1 for additional information about capacitor selection. CAPACITOR SELECTION FOR THE TIMER OSCILLATOR 3: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 4: Capacitor values are for design guidance only. 11.3.1 USING TIMER1 AS A CLOCK SOURCE The Timer1 oscillator is also available as a clock source in power-managed modes. By setting the clock select bits, SCS1:SCS0 (OSCCON<1:0>), to `01', the device switches to SEC_RUN mode; both the CPU and peripherals are clocked from the Timer1 oscillator. If the IDLEN bit (OSCCON<7>) is cleared and a SLEEP instruction is executed, the device enter SEC_IDLE mode. Additional details are available in Section 3.0 "Power-Managed Modes". Whenever the Timer1 oscillator is providing the clock source, the Timer1 system clock status flag, T1RUN (T1CON<6>), is set. This can be used to determine the controller's current clocking mode. It can also indicate the clock source being currently used by the Fail-Safe Clock Monitor. If the Clock Monitor is enabled and the Timer1 oscillator fails while providing the clock, polling the T1RUN bit will indicate whether the clock is being provided by the Timer1 oscillator or another source. 11.3.2 LOW-POWER TIMER1 OPTION The Timer1 oscillator can operate at two distinct levels of power consumption based on device configuration. When the LPT1OSC Configuration bit is set, the Timer1 oscillator operates in a low-power mode. When LPT1OSC is not set, Timer1 operates at a higher power level. Power consumption for a particular mode is relatively constant, regardless of the device's operating mode. The default Timer1 configuration is the higher power mode. As the low-power Timer1 mode tends to be more sensitive to interference, high noise environments may cause some oscillator instability. The low-power option is, therefore, best suited for low noise applications where power conservation is an important design consideration. (c) 2009 Microchip Technology Inc. DS39636D-page 121 PIC18F2X1X/4X1X 11.3.3 TIMER1 OSCILLATOR LAYOUT CONSIDERATIONS The Timer1 oscillator circuit draws very little power during operation. Due to the low-power nature of the oscillator, it may also be sensitive to rapidly changing signals in close proximity. The oscillator circuit, shown in Figure 11-3, should be located as close as possible to the microcontroller. There should be no circuits passing within the oscillator circuit boundaries other than VSS or VDD. If a high-speed circuit must be located near the oscillator (such as the CCP1 pin in Output Compare or PWM mode, or the primary oscillator using the OSC2 pin), a grounded guard ring around the oscillator circuit, as shown in Figure 11-4, may be helpful when used on a single-sided PCB or in addition to a ground plane. FIGURE 11-4: OSCILLATOR CIRCUIT WITH GROUNDED GUARD RING 11.5 If either of the CCP modules is configured to use Timer1 and generate a Special Event Trigger in Compare mode (CCP1M3:CCP1M0 or CCP2M3:CCP2M0 = 1011), this signal will reset Timer1. The trigger from CCP2 will also start an A/D conversion if the A/D module is enabled (see Section 14.3.4 "Special Event Trigger" for more information). The module must be configured as either a timer or a synchronous counter to take advantage of this feature. When used this way, the CCPRH:CCPRL register pair effectively becomes a period register for Timer1. If Timer1 is running in Asynchronous Counter mode, this Reset operation may not work. In the event that a write to Timer1 coincides with a special event trigger, the write operation will take precedence. Note: VDD VSS OSC1 OSC2 RC0 RC1 RC2 Note: Not drawn to scale. 11.4 Timer1 Interrupt The TMR1 register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The Timer1 interrupt, if enabled, is generated on overflow, which is latched in interrupt flag bit, TMR1IF (PIR1<0>). This interrupt can be enabled or disabled by setting or clearing the Timer1 Interrupt Enable bit, TMR1IE (PIE1<0>). Resetting Timer1 Using the CCP Special Event Trigger 11.6 The special event triggers from the CCP2 module will not set the TMR1IF interrupt flag bit (PIR1<0>). Using Timer1 as a Real-Time Clock Adding an external LP oscillator to Timer1 (such as the one described in Section 11.3 "Timer1 Oscillator" above) gives users the option to include RTC functionality to their applications. This is accomplished with an inexpensive watch crystal to provide an accurate time base and several lines of application code to calculate the time. When operating in Sleep mode and using a battery or supercapacitor as a power source, it can completely eliminate the need for a separate RTC device and battery backup. The application code routine, RTCisr, shown in Example 11-1, demonstrates a simple method to increment a counter at one-second intervals using an Interrupt Service Routine. Incrementing the TMR1 register pair to overflow triggers the interrupt and calls the routine, which increments the seconds counter by one; additional counters for minutes and hours are incremented as the previous counter overflow. Since the register pair is 16 bits wide, counting up to overflow the register directly from a 32.768 kHz clock would take 2 seconds. To force the overflow at the required one-second intervals, it is necessary to preload it. The simplest method is to set the MSb of TMR1H with a BSF instruction. Note that the TMR1L register is never preloaded or altered. Doing so may introduce cumulative errors over many cycles. For this method to be accurate, Timer1 must operate in Asynchronous mode and the Timer1 overflow interrupt must be enabled (PIE1<0> = 1), as shown in the routine, RTCinit. The Timer1 oscillator must also be enabled and running at all times. DS39636D-page 122 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X EXAMPLE 11-1: IMPLEMENTING A REAL-TIME CLOCK USING A TIMER1 INTERRUPT SERVICE RTCinit MOVLW MOVWF CLRF MOVLW MOVWF CLRF CLRF MOVLW MOVWF BSF RETURN 80h TMR1H TMR1L b'00001111' T1CON secs mins .12 hours PIE1, TMR1IE BSF BCF INCF MOVLW CPFSGT RETURN CLRF INCF MOVLW CPFSGT RETURN CLRF INCF MOVLW CPFSGT RETURN CLRF RETURN TMR1H, 7 PIR1, TMR1IF secs, F .59 secs ; Preload TMR1 register pair ; for 1 second overflow ; Configure for external clock, ; Asynchronous operation, external oscillator ; Initialize timekeeping registers ; ; Enable Timer1 interrupt RTCisr TABLE 11-2: Name secs mins, F .59 mins mins hours, F .23 hours ; ; ; ; Preload for 1 sec overflow Clear interrupt flag Increment seconds 60 seconds elapsed? ; ; ; ; No, done Clear seconds Increment minutes 60 minutes elapsed? ; ; ; ; No, done clear minutes Increment hours 24 hours elapsed? ; No, done ; Reset hours ; Done hours REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 TMR1L Timer1 Register, Low Byte 52 TMR1H Timer1 Register, High Byte 52 T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON 52 Legend: Shaded cells are not used by the Timer1 module. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 123 PIC18F2X1X/4X1X NOTES: DS39636D-page 124 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 12.0 TIMER2 MODULE 12.1 The Timer2 module timer incorporates the following features: * 8-bit timer and period registers (TMR2 and PR2, respectively) * Readable and writable (both registers) * Software programmable prescaler (1:1, 1:4 and 1:16) * Software programmable postscaler (1:1 through 1:16) * Interrupt on TMR2-to-PR2 match * Optional use as the shift clock for the MSSP module The module is controlled through the T2CON register (Register 12-1), which enables or disables the timer and configures the prescaler and postscaler. Timer2 can be shut off by clearing control bit, TMR2ON (T2CON<2>), to minimize power consumption. A simplified block diagram of the module is shown in Figure 12-1. Timer2 Operation In normal operation, TMR2 is incremented from 00h on each clock (FOSC/4). A 4-bit counter/prescaler on the clock input gives direct input, divide-by-4 and divide-by16 prescale options; these are selected by the prescaler control bits, T2CKPS1:T2CKPS0 (T2CON<1:0>). The value of TMR2 is compared to that of the period register, PR2, on each clock cycle. When the two values match, the comparator generates a match signal as the timer output. This signal also resets the value of TMR2 to 00h on the next cycle and drives the output counter/ postscaler (see Section 12.2 "Timer2 Interrupt"). The TMR2 and PR2 registers are both directly readable and writable. The TMR2 register is cleared on any device Reset, while the PR2 register initializes at FFh. Both the prescaler and postscaler counters are cleared on the following events: * a write to the TMR2 register * a write to the T2CON register * any device Reset (Power-on Reset, MCLR Reset, Watchdog Timer Reset or Brown-out Reset) TMR2 is not cleared when T2CON is written. REGISTER 12-1: T2CON: TIMER2 CONTROL REGISTER U-0 -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 R/W-0 T2CKPS0 bit 7 bit 0 bit 7 Unimplemented: Read as `0' bit 6-3 T2OUTPS3:T2OUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale * * * 1111 = 1:16 Postscale bit 2 TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off bit 1-0 T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 125 PIC18F2X1X/4X1X 12.2 Timer2 Interrupt 12.3 Timer2 also can generate an optional device interrupt. The Timer2 output signal (TMR2-to-PR2 match) provides the input for the 4-bit output counter/ postscaler. This counter generates the TMR2 match interrupt flag which is latched in TMR2IF (PIR1<1>). The interrupt is enabled by setting the TMR2 Match Interrupt Enable bit, TMR2IE (PIE1<1>). Timer2 Output The unscaled output of TMR2 is available primarily to the CCP modules, where it is used as a time base for operations in PWM mode. Timer2 can be optionally used as the shift clock source for the MSSP module operating in SPI mode. Additional information is provided in Section 16.0 "Master Synchronous Serial Port (MSSP) Module". A range of 16 postscale options (from 1:1 through 1:16 inclusive) can be selected with the postscaler control bits, T2OUTPS3:T2OUTPS0 (T2CON<6:3>). FIGURE 12-1: TIMER2 BLOCK DIAGRAM 4 T2OUTPS3:T2OUTPS0 Set TMR2IF 2 T2CKPS1:T2CKPS0 TMR2 Output (to PWM or MSSP) TMR2/PR2 Match Reset 1:1, 1:4, 1:16 Prescaler FOSC/4 1:1 to 1:16 Postscaler TMR2 Comparator 8 PR2 8 8 Internal Data Bus TABLE 12-1: Name REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 INTCON GIE/GIEH PEIE/GIEL TMR2 T2CON PR2 Timer2 Register -- T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON 52 T2CKPS1 T2CKPS0 Timer2 Period Register 52 52 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by the Timer2 module. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. DS39636D-page 126 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 13.0 TIMER3 MODULE The Timer3 module timer/counter incorporates these features: * Software selectable operation as a 16-bit timer or counter * Readable and writable 8-bit registers (TMR3H and TMR3L) * Selectable clock source (internal or external) with device clock or Timer1 oscillator internal options * Interrupt-on-overflow * Module Reset on CCP special event trigger REGISTER 13-1: A simplified block diagram of the Timer3 module is shown in Figure 13-1. A block diagram of the module's operation in Read/Write mode is shown in Figure 13-2. The Timer3 module is controlled through the T3CON register (Register 13-1). It also selects the clock source options for the CCP modules (see Section 14.1.1 "CCP Modules and Timer Resources" for more information). T3CON: TIMER3 CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 RD16 T3CCP2 T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON bit 7 bit 0 bit 7 RD16: 16-bit Read/Write Mode Enable bit 1 = Enables register read/write of Timer3 in one 16-bit operation 0 = Enables register read/write of Timer3 in two 8-bit operations bit 6,3 T3CCP2:T3CCP1: Timer3 and Timer1 to CCPx Enable bits 1x = Timer3 is the capture/compare clock source for the CCP modules 01 = Timer3 is the capture/compare clock source for CCP2; Timer1 is the capture/compare clock source for CCP1 00 = Timer1 is the capture/compare clock source for the CCP modules bit 5-4 T3CKPS1:T3CKPS0: Timer3 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 2 T3SYNC: Timer3 External Clock Input Synchronization Control bit (Not usable if the device clock comes from Timer1/Timer3.) When TMR3CS = 1: 1 = Do not synchronize external clock input 0 = Synchronize external clock input When TMR3CS = 0: This bit is ignored. Timer3 uses the internal clock when TMR3CS = 0. bit 1 TMR3CS: Timer3 Clock Source Select bit 1 = External clock input from Timer1 oscillator or T13CKI (on the rising edge after the first falling edge) 0 = Internal clock (FOSC/4) bit 0 TMR3ON: Timer3 On bit 1 = Enables Timer3 0 = Stops Timer3 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 127 PIC18F2X1X/4X1X 13.1 Timer3 Operation The operating mode is determined by the clock select bit, TMR3CS (T3CON<1>). When TMR3CS is cleared (= 0), Timer3 increments on every internal instruction cycle (FOSC/4). When the bit is set, Timer3 increments on every rising edge of the Timer1 external clock input or the Timer1 oscillator, if enabled. Timer3 can operate in one of three modes: * Timer * Synchronous Counter * Asynchronous Counter FIGURE 13-1: As with Timer1, the RC1/T1OSI and RC0/T1OSO/ T13CKI pins become inputs when the Timer1 oscillator is enabled. This means the values of TRISC<1:0> are ignored and the pins are read as `0'. TIMER3 BLOCK DIAGRAM Timer1 Oscillator Timer1 Clock Input 1 T1OSO/T13CKI 1 FOSC/4 Internal Clock T1OSI Synchronize Prescaler 1, 2, 4, 8 0 Detect 0 2 T1OSCEN(1) Sleep Input TMR3CS Timer3 On/Off T3CKPS1:T3CKPS0 T3SYNC TMR3ON CCP1/CCP2 Special Event Trigger CCP1/CCP2 Select from T3CON<6,3> Clear TMR3 Set TMR3IF on Overflow TMR3 High Byte TMR3L Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain. FIGURE 13-2: TIMER3 BLOCK DIAGRAM (16-BIT READ/WRITE MODE) Timer1 Oscillator Timer1 Clock Input 1 T13CKI/T1OSO 1 FOSC/4 Internal Clock T1OSI Synchronize Prescaler 1, 2, 4, 8 0 Detect 0 2 Sleep Input TMR3CS T1OSCEN(1) T3CKPS1:T3CKPS0 Timer3 On/Off T3SYNC TMR3ON CCP1/CCP2 Special Event Trigger CCP1/CCP2 Select from T3CON<6,3> Clear TMR3 Set TMR3IF on Overflow TMR3 High Byte TMR3L 8 Read TMR1L Write TMR1L 8 8 TMR3H 8 8 Internal Data Bus Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off to eliminate power drain. DS39636D-page 128 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 13.2 Timer3 16-Bit Read/Write Mode 13.4 Timer3 Interrupt Timer3 can be configured for 16-bit reads and writes (see Figure 13-2). When the RD16 control bit (T3CON<7>) is set, the address for TMR3H is mapped to a buffer register for the high byte of Timer3. A read from TMR3L will load the contents of the high byte of Timer3 into the Timer3 High Byte Buffer register. This provides the user with the ability to accurately read all 16 bits of Timer1 without having to determine whether a read of the high byte, followed by a read of the low byte, has become invalid due to a rollover between reads. The TMR3 register pair (TMR3H:TMR3L) increments from 0000h to FFFFh and overflows to 0000h. The Timer3 interrupt, if enabled, is generated on overflow and is latched in interrupt flag bit, TMR3IF (PIR2<1>). This interrupt can be enabled or disabled by setting or clearing the Timer3 Interrupt Enable bit, TMR3IE (PIE2<1>). A write to the high byte of Timer3 must also take place through the TMR3H Buffer register. The Timer3 high byte is updated with the contents of TMR3H when a write occurs to TMR3L. This allows a user to write all 16 bits to both the high and low bytes of Timer3 at once. If either of the CCP modules is configured to use Timer3 and to generate a special event trigger in Compare mode (CCP1M3:CCP1M0 or CCP2M3:CCP2M0 = 1011), this signal will reset Timer3. It will also start an A/D conversion if the A/D module is enabled (see Section 14.3.4 "Special Event Trigger" for more information). The high byte of Timer3 is not directly readable or writable in this mode. All reads and writes must take place through the Timer3 High Byte Buffer register. Writes to TMR3H do not clear the Timer3 prescaler. The prescaler is only cleared on writes to TMR3L. 13.3 Using the Timer1 Oscillator as the Timer3 Clock Source The Timer1 internal oscillator may be used as the clock source for Timer3. The Timer1 oscillator is enabled by setting the T1OSCEN (T1CON<3>) bit. To use it as the Timer3 clock source, the TMR3CS bit must also be set. As previously noted, this also configures Timer3 to increment on every rising edge of the oscillator source. 13.5 Resetting Timer3 Using the CCP Special Event Trigger The module must be configured as either a timer or synchronous counter to take advantage of this feature. When used this way, the CCPR2H:CCPR2L register pair effectively becomes a period register for Timer3. If Timer3 is running in Asynchronous Counter mode, the Reset operation may not work. In the event that a write to Timer3 coincides with a special event trigger from a CCP module, the write will take precedence. Note: The special event triggers from the CCP2 module will not set the TMR3IF interrupt flag bit (PIR1<0>). The Timer1 oscillator is described in Section 11.0 "Timer1 Module". TABLE 13-1: Name INTCON REGISTERS ASSOCIATED WITH TIMER3 AS A TIMER/COUNTER Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 Bit 6 GIE/GIEH PEIE/GIEL PIR2 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 54 PIE2 OSCFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE 54 IPR2 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 54 TMR3L Timer3 Register, Low Byte 53 TMR3H Timer3 Register, High Byte 53 T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON 52 T3CON RD16 T3CCP2 T3CKPS1 T3CKPS0 TMR3CS TMR3ON 53 T3CCP1 T3SYNC Legend: -- = unimplemented, read as `0'. Shaded cells are not used by the Timer3 module. (c) 2009 Microchip Technology Inc. DS39636D-page 129 PIC18F2X1X/4X1X NOTES: DS39636D-page 130 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 14.0 CAPTURE/COMPARE/PWM (CCP) MODULES The Capture and Compare operations described in this chapter apply to all standard and Enhanced CCP modules. PIC18F2X1X/4X1X devices all have two CCP (Capture/Compare/PWM) modules. Each module contains a 16-bit register which can operate as a 16-bit Capture register, a 16-bit Compare register or a PWM Master/Slave Duty Cycle register. In 28-pin devices, the two standard CCP modules (CCP1 and CCP2) operate as described in this chapter. In 40/44-pin devices, CCP1 is implemented as an Enhanced CCP module with standard Capture and Compare modes and Enhanced PWM modes. The ECCP implementation is discussed in Section 15.0 "Enhanced Capture/Compare/PWM (ECCP) Module". REGISTER 14-1: Note: Throughout this section and Section 15.0 "Enhanced Capture/Compare/PWM (ECCP) Module", references to the register and bit names for CCP modules are referred to generically by the use of `x' or `y' in place of the specific module number. Thus, "CCPxCON" might refer to the control register for CCP1, CCP2 or ECCP1. "CCPxCON" is used throughout these sections to refer to the module control register, regardless of whether the CCP module is a standard or Enhanced implementation. CCPXCON REGISTER (CCP2 MODULE, CCP1 MODULE IN 28-PIN DEVICES) U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- DCxB1 DCxB0 CCPxM3 CCPxM2 R/W-0 R/W-0 CCPxM1 CCPxM0 bit 7 bit 0 bit 7-6 Unimplemented: Read as `0' bit 5-4 DCxB1:DCxB0: PWM Duty Cycle bit 1 and bit 0 for CCP Module x Capture mode: Unused. Compare mode: Unused. PWM mode: These bits are the two LSbs (bit 1 and bit 0) of the 10-bit PWM duty cycle. The eight MSbs (DCx9:DCx2) of the duty cycle are found in CCPRxL. bit 3-0 CCPxM3:CCPxM0: CCP Module x Mode Select bits 0000 = Capture/Compare/PWM disabled (resets CCP module) 0001 = Reserved 0010 = Compare mode, toggle output on match (CCPIF bit is set) 0011 = Reserved 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode: initialize CCP pin low; on compare match, force CCP pin high (CCPIF bit is set) 1001 = Compare mode: initialize CCP pin high; on compare match, force CCP pin low (CCPIF bit is set) 1010 = Compare mode: generate software interrupt on compare match (CCPIF bit is set, CCP pin reflects I/O state) 1011 = Compare mode: trigger special event, reset timer, start A/D conversion on CCP2 match (CCPxIF bit is set) 11xx = PWM mode Legend: R = Readable bit -n = Value at POR (c) 2009 Microchip Technology Inc. W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown DS39636D-page 131 PIC18F2X1X/4X1X 14.1 CCP Module Configuration Each Capture/Compare/PWM module is associated with a control register (generically, CCPxCON) and a data register (CCPRx). The data register, in turn, is comprised of two 8-bit registers: CCPRxL (low byte) and CCPRxH (high byte). All registers are both readable and writable. 14.1.1 CCP MODULES AND TIMER RESOURCES The CCP modules utilize Timers 1, 2 or 3, depending on the mode selected. Timer1 and Timer3 are available to modules in Capture or Compare modes, while Timer2 is available for modules in PWM mode. TABLE 14-1: CCP MODE - TIMER RESOURCE CCP/ECCP Mode Timer Resource Capture Compare PWM Timer1 or Timer3 Timer1 or Timer3 Timer2 TABLE 14-2: The assignment of a particular timer to a module is determined by the Timer-to-CCP enable bits in the T3CON register (Register 13-1). Both modules may be active at any given time and may share the same timer resource if they are configured to operate in the same mode (Capture/Compare or PWM) at the same time. The interactions between the two modules are summarized in Figure 14-1 and Figure 14-2. In Timer1 in Asynchronous Counter mode, the capture operation will not work. 14.1.2 CCP2 PIN ASSIGNMENT The pin assignment for CCP2 (Capture input, Compare and PWM output) can change, based on device configuration. The CCP2MX Configuration bit determines which pin CCP2 is multiplexed to. By default, it is assigned to RC1 (CCP2MX = 1). If the Configuration bit is cleared, CCP2 is multiplexed with RB3. Changing the pin assignment of CCP2 does not automatically change any requirements for configuring the port pin. Users must always verify that the appropriate TRIS register is configured correctly for CCP2 operation, regardless of where it is located. INTERACTIONS BETWEEN CCP1 AND CCP2 FOR TIMER RESOURCES CCP1 Mode CCP2 Mode Interaction Capture Capture Each module can use TMR1 or TMR3 as the time base. The time base can be different for each CCP. Capture Compare CCP2 can be configured for the special event trigger to reset TMR1 or TMR3 (depending upon which time base is used). Automatic A/D conversions on trigger event can also be done. Operation of CCP1 could be affected if it is using the same timer as a time base. Compare Capture CCP1 can be configured for the special event trigger to reset TMR1 or TMR3 (depending upon which time base is used). Operation of CCP2 could be affected if it is using the same timer as a time base. Compare Compare Either module can be configured for the Special Event Trigger to reset the time base. Automatic A/D conversions on CCP2 trigger event can be done. Conflicts may occur if both modules are using the same time base. Capture PWM(1) None Compare PWM(1) None PWM(1) Capture None Compare None (1) PWM PWM(1) Note 1: PWM Both PWMs will have the same frequency and update rate (TMR2 interrupt). Includes standard and Enhanced PWM operation. DS39636D-page 132 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 14.2 Capture Mode 14.2.3 When the Capture mode is changed, a false capture interrupt may be generated. The user should keep the CCPxIE interrupt enable bit clear to avoid false interrupts. The interrupt flag bit, CCPxIF, should also be cleared following any such change in operating mode. In Capture mode, the CCPRxH:CCPRxL register pair captures the 16-bit value of the TMR1 or TMR3 registers when an event occurs on the corresponding CCPx pin. An event is defined as one of the following: * * * * every falling edge every rising edge every 4th rising edge every 16th rising edge 14.2.4 Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared; therefore, the first capture may be from a non-zero prescaler. Example 14-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the "false" interrupt. CCP PIN CONFIGURATION In Capture mode, the appropriate CCPx pin should be configured as an input by setting the corresponding TRIS direction bit. Note: 14.2.2 If RB3/CCP2 or RC1/CCP2 is configured as an output, a write to the port can cause a capture condition. EXAMPLE 14-1: TIMER1/TIMER3 MODE SELECTION CLRF MOVLW The timers that are to be used with the capture feature (Timer1 and/or Timer3) must be running in Timer mode or Synchronized Counter mode. In Asynchronous Counter mode, the capture operation will not work. The timer to be used with each CCP module is selected in the T3CON register (see Section 14.1.1 "CCP Modules and Timer Resources"). FIGURE 14-1: CCP PRESCALER There are four prescaler settings in Capture mode; they are specified as part of the operating mode selected by the mode select bits (CCPxM3:CCPxM0). Whenever the CCP module is turned off or Capture mode is disabled, the prescaler counter is cleared. This means that any Reset will clear the prescaler counter. The event is selected by the mode select bits, CCPxM3:CCPxM0 (CCPxCON<3:0>). When a capture is made, the interrupt request flag bit, CCPxIF, is set; it must be cleared in software. If another capture occurs before the value in register CCPRx is read, the old captured value is overwritten by the new captured value. 14.2.1 SOFTWARE INTERRUPT MOVWF CHANGING BETWEEN CAPTURE PRESCALERS (CCP2 SHOWN) CCP2CON ; Turn CCP module off NEW_CAPT_PS ; Load WREG with the ; new prescaler mode ; value and CCP ON CCP2CON ; Load CCP2CON with ; this value CAPTURE MODE OPERATION BLOCK DIAGRAM TMR3H Set CCP1IF T3CCP2 CCP1 pin Prescaler / 1, 4, 16 and Edge Detect CCP1CON<3:0> Q1:Q4 CCP2CON<3:0> 4 4 CCPR1L TMR1 Enable TMR1H TMR1L TMR3H TMR3L Set CCP2IF 4 T3CCP1 T3CCP2 CCP2 pin Prescaler / 1, 4, 16 TMR3 Enable CCPR1H T3CCP2 TMR3L and Edge Detect TMR3 Enable CCPR2H CCPR2L TMR1 Enable T3CCP2 T3CCP1 (c) 2009 Microchip Technology Inc. TMR1H TMR1L DS39636D-page 133 PIC18F2X1X/4X1X 14.3 Compare Mode 14.3.2 TIMER1/TIMER3 MODE SELECTION In Compare mode, the 16-bit CCPRx register value is constantly compared against either the TMR1 or TMR3 register pair value. When a match occurs, the CCPx pin can be: Timer1 and/or Timer3 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. * * * * 14.3.3 driven high driven low toggled (high-to-low or low-to-high) remain unchanged (that is, reflects the state of the I/O latch) When the Generate Software Interrupt mode is chosen (CCPxM3:CCPxM0 = 1010), the corresponding CCPx pin is not affected. Only a CCP interrupt is generated, if enabled and the CCPxIE bit is set. The action on the pin is based on the value of the mode select bits (CCPxM3:CCPxM0). At the same time, the interrupt flag bit CCPxIF is set. 14.3.1 14.3.4 SPECIAL EVENT TRIGGER Both CCP modules are equipped with a special event trigger. This is an internal hardware signal generated in Compare mode to trigger actions by other modules. The special event trigger is enabled by selecting the Compare Special Event Trigger mode (CCPxM3:CCPxM0 = 1011). CCP PIN CONFIGURATION The user must configure the CCPx pin as an output by clearing the appropriate TRIS bit. Note: SOFTWARE INTERRUPT MODE Clearing the CCP2CON register will force the RB3 or RC1 compare output latch (depending on device configuration) to the default low level. This is not the PORTB or PORTC I/O data latch. For either CCP module, the special event trigger resets the timer register pair for whichever timer resource is currently assigned as the module's time base. This allows the CCPRx registers to serve as a programmable period register for either timer. The special event trigger for CCP2 can also start an A/D conversion. In order to do this, the A/D converter must already be enabled. FIGURE 14-2: COMPARE MODE OPERATION BLOCK DIAGRAM CCPR1H Set CCP1IF CCPR1L Special Event Trigger (Timer1/Timer3 Reset) CCP1 pin Comparator Output Logic Compare Match S Q R TRIS Output Enable 4 CCP1CON<3:0> 0 TMR1H TMR1L 1 TMR3H TMR3L T3CCP1 0 Special Event Trigger (Timer1/Timer3 Reset, A/D Trigger) 1 T3CCP2 Set CCP2IF Comparator CCPR2H CCPR2L Compare Match CCP2 pin Output Logic 4 S Q R TRIS Output Enable CCP2CON<3:0> DS39636D-page 134 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 14-3: Name INTCON REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, TIMER1 AND TIMER3 Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 Bit 6 GIE/GIEH PEIE/GIEL (2) -- RI TO PD POR BOR 50 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 (1) PSPIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 RCON IPEN SBOREN PIR2 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 54 PIE2 OSCFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE 54 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 54 IPR2 TRISB PORTB Data Direction Control Register 54 TRISC PORTC Data Direction Control Register 54 TMR1L Timer1 Register Low Byte 52 TMR1H Timer1 Register High Byte T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR3H Timer3 Register High Byte TMR3L Timer3 Register Low Byte T3CON RD16 T3CCP2 52 TMR1CS TMR1ON 52 53 53 T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON 53 CCPR1L Capture/Compare/PWM Register 1 Low Byte 53 CCPR1H Capture/Compare/PWM Register 1 High Byte 53 CCP1CON P1M1(1) P1M0(1) DC1B1 DC1B0 CCPR2L Capture/Compare/PWM Register 2 Low Byte CCPR2H Capture/Compare/PWM Register 2 High Byte CCP2CON -- -- DC2B1 DC2B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 53 53 53 CCP2M3 CCP2M2 CCP2M1 CCP2M0 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by Capture/Compare, Timer1 or Timer3. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. 2: The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". (c) 2009 Microchip Technology Inc. DS39636D-page 135 PIC18F2X1X/4X1X 14.4 PWM Mode 14.4.1 In Pulse-Width Modulation (PWM) mode, the CCPx pin produces up to a 10-bit resolution PWM output. Since the CCP2 pin is multiplexed with a PORTB or PORTC data latch, the appropriate TRIS bit must be cleared to make the CCP2 pin an output. Note: Clearing the CCP2CON register will force the RB3 or RC1 output latch (depending on device configuration) to the default low level. This is not the PORTB or PORTC I/O data latch. Figure 14-3 shows a simplified block diagram of the CCP module in PWM mode. For a step-by-step procedure on how to set up the CCP module for PWM operation, see Section 14.4.4 "Setup for PWM Operation". FIGURE 14-3: SIMPLIFIED PWM BLOCK DIAGRAM The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: EQUATION 14-1: PWM Period = [(PR2) + 1] * 4 * TOSC * (TMR2 Prescale Value) PWM frequency is defined as 1/[PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCPx pin is set (exception: if PWM duty cycle = 0%, the CCPx pin will not be set) * The PWM duty cycle is latched from CCPRxL into CCPRxH Note: CCPxCON<5:4> Duty Cycle Registers CCPRxL 14.4.2 CCPRxH (Slave) CCPx Output R Comparator TMR2 (Note 1) Comparator S Clear Timer, CCP1 pin and latch D.C. PR2 Q Corresponding TRIS bit Note 1: The 8-bit TMR2 value is concatenated with 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit time base. A PWM output (Figure 14-4) has a time base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/period). FIGURE 14-4: PWM PERIOD The Timer2 postscalers (see Section 12.0 "Timer2 Module") are not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. PWM DUTY CYCLE The PWM duty cycle is specified by writing to the CCPRxL register and to the CCPxCON<5:4> bits. Up to 10-bit resolution is available. The CCPRxL contains the eight MSbs and the CCPxCON<5:4> contains the two LSbs. This 10-bit value is represented by CCPRxL:CCPxCON<5:4>. The following equation is used to calculate the PWM duty cycle in time: EQUATION 14-2: PWM Duty Cycle = (CCPRXL:CCPXCON<5:4>) * TOSC * (TMR2 Prescale Value) CCPRxL and CCPxCON<5:4> can be written to at any time but the duty cycle value is not latched into CCPR2H until after a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPRxH is a read-only register. PWM OUTPUT Period Duty Cycle TMR2 = PR2 TMR2 = Duty Cycle TMR2 = PR2 DS39636D-page 136 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X The CCPRxH register and a 2-bit internal latch are used to double-buffer the PWM duty cycle. This double-buffering is essential for glitchless PWM operation. EQUATION 14-3: F OSC log --------------- F PWM PWM Resolution (max) = -----------------------------bits log ( 2 ) When the CCPRxH and 2-bit latch match TMR2, concatenated with an internal 2-bit Q clock or 2 bits of the TMR2 prescaler, the CCPx pin is cleared. Note: The maximum PWM resolution (bits) for a given PWM frequency is given by the equation: TABLE 14-4: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz PWM Frequency Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) 14.4.3 If the PWM duty cycle value is longer than the PWM period, the CCP2 pin will not be cleared. 2.44 kHz 9.77 kHz 39.06 kHz 156.25 kHz 312.50 kHz 416.67 kHz 16 4 1 1 1 1 FFh FFh FFh 3Fh 1Fh 17h 10 10 10 8 7 6.58 PWM AUTO-SHUTDOWN (CCP1 ONLY) The PWM auto-shutdown features of the Enhanced CCP module are also available to CCP1 in 28-pin devices. The operation of this feature is discussed in detail in Section 15.4.7 "Enhanced PWM Auto-Shutdown". Auto-shutdown features are not available for CCP2. 14.4.4 The following steps should be taken when configuring the CCP module for PWM operation: 1. 2. 3. 4. 5. (c) 2009 Microchip Technology Inc. SETUP FOR PWM OPERATION Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPRxL register and CCPxCON<5:4> bits. Make the CCPx pin an output by clearing the appropriate TRIS bit. Set the TMR2 prescale value, then enable Timer2 by writing to T2CON. Configure the CCPx module for PWM operation. DS39636D-page 137 PIC18F2X1X/4X1X TABLE 14-5: Name INTCON REGISTERS ASSOCIATED WITH PWM AND TIMER2 Bit 7 Bit 6 GIE/GIEH PEIE/GIEL (2) Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 -- RI TO PD POR BOR 50 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE (1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 RCON IPEN SBOREN Bit 5 TRISB PORTB Data Direction Control Register 54 TRISC PORTC Data Direction Control Register 54 TMR2 Timer2 Register 52 PR2 Timer2 Period Register 52 T2CON -- T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0 CCPR1L Capture/Compare/PWM Register 1 Low Byte CCPR1H Capture/Compare/PWM Register 1 High Byte CCP1CON P1M1(1) P1M0(1) DC1B1 DC1B0 52 53 53 CCP1M3 CCP1M2 CCP1M1 CCP1M0 53 CCPR2L Capture/Compare/PWM Register 2 Low Byte 53 CCPR2H Capture/Compare/PWM Register 2 High Byte 53 CCP2CON ECCP1AS PWM1CON -- -- ECCPASE ECCPAS2 PRSEN PDC6(1) DC2B1 DC2B0 CCP2M3 CCP2M2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1(1) PSSBD0(1) CCP2M1 53 PDC5(1) PDC4(1) PDC3(1) PDC2(1) 53 PDC1(1) CCP2M0 PDC0(1) 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by PWM or Timer2. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. 2: The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". DS39636D-page 138 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 15.0 Note: ENHANCED CAPTURE/ COMPARE/PWM (ECCP) MODULE and restart. The Enhanced features are discussed in detail in Section 15.4 "Enhanced PWM Mode". Capture, Compare and single-output PWM functions of the ECCP module are the same as described for the standard CCP module. The ECCP module is implemented only in 40/44-pin devices. The control register for the Enhanced CCP module is shown in Register 15-1. It differs from the CCPxCON registers in PIC18F2410/2415/2510/2515/2610 devices in that the two Most Significant bits are implemented to control PWM functionality. In PIC18F4410/4415/4510/4515/4610 devices, CCP1 is implemented as a standard CCP module with enhanced PWM capabilities. These include the provision for 2 or 4 output channels, user selectable polarity, dead-band control and automatic shutdown REGISTER 15-1: CCP1CON REGISTER (ECCP1 MODULE, 40/44-PIN DEVICES) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 bit 7 bit 0 bit 7-6 P1M1:P1M0: Enhanced PWM Output Configuration bits If CCP1M3:CCP1M2 = 00, 01, 10: xx = P1A assigned as Capture/Compare input/output; P1B, P1C, P1D assigned as port pins If CCP1M3:CCP1M2 = 11: 00 = Single output: P1A modulated; P1B, P1C, P1D assigned as port pins 01 = Full-bridge output forward: P1D modulated; P1A active; P1B, P1C inactive 10 = Half-bridge output: P1A, P1B modulated with dead-band control; P1C, P1D assigned as port pins 11 = Full-bridge output reverse: P1B modulated; P1C active; P1A, P1D inactive bit 5-4 DC1B1:DC1B0: PWM Duty Cycle bit 1 and bit 0 Capture mode: Unused. Compare mode: Unused. PWM mode: These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found in CCPR1L. bit 3-0 CCP1M3:CCP1M0: Enhanced CCP Mode Select bits 0000 = Capture/Compare/PWM off (resets ECCP module) 0001 = Reserved 0010 = Compare mode, toggle output on match 0011 = Capture mode 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, initialize CCP1 pin low, set output on compare match (set CCP1IF) 1001 = Compare mode, initialize CCP1 pin high, clear output on compare match (set CCP1IF) 1010 = Compare mode, generate software interrupt only, CCP1 pin reverts to I/O state 1011 = Compare mode, trigger special event (ECCP resets TMR1 or TMR3, sets CC1IF bit) 1100 = PWM mode; P1A, P1C active-high; P1B, P1D active-high 1101 = PWM mode; P1A, P1C active-high; P1B, P1D active-low 1110 = PWM mode; P1A, P1C active-low; P1B, P1D active-high 1111 = PWM mode; P1A, P1C active-low; P1B, P1D active-low Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 139 PIC18F2X1X/4X1X In addition to the expanded range of modes available through the CCP1CON and ECCP1AS registers, the ECCP module has an additional register associated with Enhanced PWM operation and auto-shutdown features. This register is: * PWM1CON (PWM Configuration register) 15.1 ECCP Outputs and Configuration The Enhanced CCP module may have up to four PWM outputs, depending on the selected operating mode. These outputs, designated P1A through P1D, are multiplexed with I/O pins on PORTC and PORTD. The outputs that are active depend on the CCP operating mode selected. The pin assignments are summarized in Table 15-1. To configure the I/O pins as PWM outputs, the proper PWM mode must be selected by setting the P1M1:P1M0 and CCP1M3:CCP1M0 bits. The appropriate TRISC and TRISD direction bits for the port pins must also be set as outputs. 15.1.1 ECCP MODULES AND TIMER RESOURCES Like the standard CCP modules, the ECCP module can utilize Timers 1, 2 or 3, depending on the mode selected. Timer1 and Timer3 are available for modules in Capture or Compare modes, while Timer2 is available for modules in PWM mode. Interactions between the standard and Enhanced CCP modules are identical to those described for standard CCP modules. Additional details on timer resources are provided in Section 14.1.1 "CCP Modules and Timer Resources". TABLE 15-1: 15.2 Capture and Compare Modes Except for the operation of the special event trigger discussed below, the Capture and Compare modes of the ECCP module are identical in operation to that of CCP2. These are discussed in detail in Section 14.2 "Capture Mode" and Section 14.3 "Compare Mode". No changes are required when moving between 28-pin and 40/44-pin devices. 15.2.1 SPECIAL EVENT TRIGGER The special event trigger output of ECCP1 resets the TMR1 or TMR3 register pair, depending on which timer resource is currently selected. This allows the CCPR1 register to effectively be a 16-bit programmable period register for Timer1 or Timer3. 15.3 Standard PWM Mode When configured in Single Output mode, the ECCP module functions identically to the standard CCP module in PWM mode, as described in Section 14.4 "PWM Mode". This is also sometimes referred to as "Compatible CCP" mode, as in Table 15-1. Note: When setting up single output PWM operations, users are free to use either of the processes described in Section 14.4.4 "Setup for PWM Operation" or Section 15.4.9 "Setup for PWM Operation". The latter is more generic and will work for either single or multi-output PWM. PIN ASSIGNMENTS FOR VARIOUS ECCP1 MODES ECCP Mode CCP1CON Configuration RC2 RD5 RD6 RD7 All 40/44-pin devices: Compatible CCP 00xx 11xx CCP1 RD5/PSP5 RD6/PSP6 RD7/PSP7 Dual PWM 10xx 11xx P1A P1B RD6/PSP6 RD7/PSP7 Quad PWM x1xx 11xx P1A P1B P1C P1D Legend: x = Don't care. Shaded cells indicate pin assignments not used by ECCP1 in a given mode. DS39636D-page 140 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 15.4 Enhanced PWM Mode 15.4.1 The Enhanced PWM mode provides additional PWM output options for a broader range of control applications. The module is a backward compatible version of the standard CCP module and offers up to four outputs, designated P1A through P1D. Users are also able to select the polarity of the signal (either active-high or active-low). The module's output mode and polarity are configured by setting the P1M1:P1M0 and CCP1M3:CCP1M0 bits of the CCP1CON register. Figure 15-1 shows a simplified block diagram of PWM operation. All control registers are double-buffered and are loaded at the beginning of a new PWM cycle (the period boundary when Timer2 resets) in order to prevent glitches on any of the outputs. The exception is the PWM Delay register, PWM1CON, which is loaded at either the duty cycle boundary or the period boundary (whichever comes first). Because of the buffering, the module waits until the assigned timer resets instead of starting immediately. This means that Enhanced PWM waveforms do not exactly match the standard PWM waveforms, but are instead offset by one full instruction cycle (4 TOSC). PWM PERIOD The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following equation. EQUATION 15-1: PWM Period = [(PR2) + 1] * 4 * TOSC * (TMR2 Prescale Value) PWM frequency is defined as 1/[PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCP1 pin is set (if PWM duty cycle = 0%, the CCP1 pin will not be set) * The PWM duty cycle is copied from CCPR1L into CCPR1H Note: As before, the user must manually configure the appropriate TRIS bits for output. FIGURE 15-1: The Timer2 postscaler (see Section 12.0 "Timer2 Module") is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODULE CCP1CON<5:4> Duty Cycle Registers CCP1M<3:0> 4 P1M1<1:0> 2 CCPR1L CCP1/P1A CCP1/P1A TRISx<x> CCPR1H (Slave) P1B R Comparator Q Output Controller P1B TRISx<x> P1C TMR2 Comparator PR2 (Note 1) P1C TRISx<x> S P1D Clear Timer, set CCP1 pin and latch D.C. P1D TRISx<x> PWM1CON Note: The 8-bit TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler, to create the 10-bit time base. (c) 2009 Microchip Technology Inc. DS39636D-page 141 PIC18F2X1X/4X1X 15.4.2 PWM DUTY CYCLE EQUATION 15-3: The PWM duty cycle is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available. The CCPR1L contains the eight MSbs and the CCP1CON<5:4> contains the two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. The PWM duty cycle is calculated by the following equation. ( log FOSC FPWM PWM Resolution (max) = log(2) Note: EQUATION 15-2: PWM Duty Cycle = (CCPR1L:CCP1CON<5:4>) * TOSC * (TMR2 Prescale Value) 15.4.3 CCPR1L and CCP1CON<5:4> can be written to at any time, but the duty cycle value is not copied into CCPR1H until a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. The CCPR1H register and a 2-bit internal latch are used to double-buffer the PWM duty cycle. This double-buffering is essential for glitchless PWM operation. When the CCPR1H and 2-bit latch match TMR2, concatenated with an internal 2-bit Q clock or two bits of the TMR2 prescaler, the CCP1 pin is cleared. The maximum PWM resolution (bits) for a given PWM frequency is given by the following equation. TABLE 15-2: ) bits If the PWM duty cycle value is longer than the PWM period, the CCP1 pin will not be cleared. PWM OUTPUT CONFIGURATIONS The P1M1:P1M0 bits in the CCP1CON register allow one of four configurations: * * * * Single Output Half-Bridge Output Full-Bridge Output, Forward mode Full-Bridge Output, Reverse mode The Single Output mode is the standard PWM mode discussed in Section 15.4 "Enhanced PWM Mode". The Half-Bridge and Full-Bridge Output modes are covered in detail in the sections that follow. The general relationship of the outputs in all configurations is summarized in Figure 15-2. EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz PWM Frequency Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) DS39636D-page 142 2.44 kHz 9.77 kHz 39.06 kHz 156.25 kHz 312.50 kHz 416.67 kHz 16 4 1 1 1 1 FFh FFh FFh 3Fh 1Fh 17h 10 10 10 8 7 6.58 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 15-2: PWM OUTPUT RELATIONSHIPS (ACTIVE-HIGH STATE) CCP1CON <7:6> 00 (Single Output) SIGNAL 0 PR2 + 1 Duty Cycle Period P1A Modulated Delay(1) Delay(1) P1A Modulated 10 (Half-Bridge) P1B Modulated P1A Active 01 (Full-Bridge, Forward) P1B Inactive P1C Inactive P1D Modulated P1A Inactive 11 (Full-Bridge, Reverse) P1B Modulated P1C Active P1D Inactive FIGURE 15-3: PWM OUTPUT RELATIONSHIPS (ACTIVE-LOW STATE) CCP1CON <7:6> 00 (Single Output) SIGNAL 0 Period P1A Modulated P1A Modulated 10 (Half-Bridge) PR2 + 1 Duty Cycle Delay(1) Delay(1) P1B Modulated P1A Active 01 (Full-Bridge, Forward) P1B Inactive P1C Inactive P1D Modulated P1A Inactive 11 (Full-Bridge, Reverse) P1B Modulated P1C Active P1D Inactive Relationships: * Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value) * Duty Cycle = TOSC * (CCPR1L<7:0>:CCP1CON<5:4>) * (TMR2 Prescale Value) * Delay = 4 * TOSC * (ECCPDEL<6:0>) Note 1: Dead-band delay is programmed using the PWM1CON register (Section 15.4.6 "Programmable Dead-Band Delay"). (c) 2009 Microchip Technology Inc. DS39636D-page 143 PIC18F2X1X/4X1X 15.4.4 HALF-BRIDGE MODE FIGURE 15-4: In the Half-Bridge Output mode, two pins are used as outputs to drive push-pull loads. The PWM output signal is output on the P1A pin, while the complementary PWM output signal is output on the P1B pin (Figure 15-4). This mode can be used for half-bridge applications, as shown in Figure 15-5, or for full-bridge applications where four power switches are being modulated with two PWM signals. HALF-BRIDGE PWM OUTPUT Period Period Duty Cycle P1A(2) td td P1B(2) In Half-Bridge Output mode, the programmable deadband delay can be used to prevent shoot-through current in half-bridge power devices. The value of bits PDC6:PDC0 sets the number of instruction cycles before the output is driven active. If the value is greater than the duty cycle, the corresponding output remains inactive during the entire cycle. See Section 15.4.6 "Programmable Dead-Band Delay" for more details of the dead-band delay operations. (1) (1) (1) td = Dead-Band Delay Note 1: At this time, the TMR2 register is equal to the PR2 register. 2: Output signals are shown as active-high. Since the P1A and P1B outputs are multiplexed with the PORTC<2> and PORTD<5> data latches, the TRISC<2> and TRISD<5> bits must be cleared to configure P1A and P1B as outputs. FIGURE 15-5: EXAMPLES OF HALF-BRIDGE OUTPUT MODE APPLICATIONS V+ Standard Half-Bridge Circuit ("Push-Pull") PIC18F4X1X FET Driver + V - P1A Load FET Driver + V - P1B V- Half-Bridge Output Driving a Full-Bridge Circuit V+ PIC18F4X1X FET Driver FET Driver P1A FET Driver Load FET Driver P1B V- DS39636D-page 144 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 15.4.5 FULL-BRIDGE MODE In Full-Bridge Output mode, four pins are used as outputs; however, only two outputs are active at a time. In the Forward mode, pin P1A is continuously active and pin P1D is modulated. In the Reverse mode, pin P1C is continuously active and pin P1B is modulated. These are illustrated in Figure 15-6. FIGURE 15-6: P1A, P1B, P1C and P1D outputs are multiplexed with the PORTC<2> and PORTD<7:5> data latches. The TRISC<2> and TRISD<7:5> bits must be cleared to make the P1A, P1B, P1C and P1D pins outputs. FULL-BRIDGE PWM OUTPUT Forward Mode Period P1A (2) Duty Cycle P1B(2) P1C(2) P1D(2) (1) (1) Reverse Mode Period Duty Cycle P1A(2) P1B(2) P1C(2) P1D(2) (1) (1) Note 1: At this time, the TMR2 register is equal to the PR2 register. Note 2: Output signal is shown as active-high. (c) 2009 Microchip Technology Inc. DS39636D-page 145 PIC18F2X1X/4X1X FIGURE 15-7: EXAMPLE OF FULL-BRIDGE APPLICATION V+ PIC18F4X1X FET Driver QC QA FET Driver P1A Load P1B FET Driver P1C FET Driver QD QB VP1D 15.4.5.1 Direction Change in Full-Bridge Mode In the Full-Bridge Output mode, the P1M1 bit in the CCP1CON register allows user to control the forward/ reverse direction. When the application firmware changes this direction control bit, the module will assume the new direction on the next PWM cycle. Just before the end of the current PWM period, the modulated outputs (P1B and P1D) are placed in their inactive state, while the unmodulated outputs (P1A and P1C) are switched to drive in the opposite direction. This occurs in a time interval of 4 TOSC * (Timer2 Prescale Value) before the next PWM period begins. The Timer2 prescaler will be either 1, 4 or 16, depending on the value of the T2CKPS bit (T2CON<1:0>). During the interval from the switch of the unmodulated outputs to the beginning of the next period, the modulated outputs (P1B and P1D) remain inactive. This relationship is shown in Figure 15-8. Note that in the Full-Bridge Output mode, the CCP1 module does not provide any dead-band delay. In general, since only one output is modulated at all times, dead-band delay is not required. However, there is a situation where a dead-band delay might be required. This situation occurs when both of the following conditions are true: 1. 2. Figure 15-9 shows an example where the PWM direction changes from forward to reverse at a near 100% duty cycle. At time t1, the outputs P1A and P1D become inactive, while output P1C becomes active. In this example, since the turn-off time of the power devices is longer than the turn-on time, a shoot-through current may flow through power devices, QC and QD (see Figure 15-7), for the duration of `t'. The same phenomenon will occur to power devices, QA and QB, for PWM direction change from reverse to forward. If changing PWM direction at high duty cycle is required for an application, one of the following requirements must be met: 1. 2. Reduce PWM for a PWM period before changing directions. Use switch drivers that can drive the switches off faster than they can drive them on. Other options to prevent shoot-through current may exist. The direction of the PWM output changes when the duty cycle of the output is at or near 100%. The turn-off time of the power switch, including the power device and driver circuit, is greater than the turn-on time. DS39636D-page 146 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 15-8: PWM DIRECTION CHANGE Period(1) SIGNAL Period P1A (Active-High) P1B (Active-High) DC P1C (Active-High) (Note 2) P1D (Active-High) DC Note 1: The direction bit in the CCP1 Control register (CCP1CON<7>) is written any time during the PWM cycle. 2: When changing directions, the P1A and P1C signals switch before the end of the current PWM cycle at intervals of 4 TOSC, 16 TOSC or 64 TOSC, depending on the Timer2 prescaler value. The modulated P1B and P1D signals are inactive at this time. FIGURE 15-9: PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE Forward Period t1 Reverse Period P1A(1) P1B(1) DC P1C(1) P1D(1) DC tON(2) External Switch C(1) tOFF(3) External Switch D(1) Potential Shoot-Through Current(1) t = tOFF - tON(2,3) Note 1: All signals are shown as active-high. 2: tON is the turn-on delay of power switch QC and its driver. 3: tOFF is the turn-off delay of power switch QD and its driver. (c) 2009 Microchip Technology Inc. DS39636D-page 147 PIC18F2X1X/4X1X 15.4.6 Note: PROGRAMMABLE DEAD-BAND DELAY Programmable dead-band delay is not implemented in 28-pin devices with standard CCP modules. In half-bridge applications where all power switches are modulated at the PWM frequency at all times, the power switches normally require more time to turn off than to turn on. If both the upper and lower power switches are switched at the same time (one turned on and the other turned off), both switches may be on for a short period of time until one switch completely turns off. During this brief interval, a very high current (shootthrough current) may flow through both power switches, shorting the bridge supply. To avoid this potentially destructive shoot-through current from flowing during switching, turning on either of the power switches is normally delayed to allow the other switch to completely turn off. In the Half-Bridge Output mode, a digitally programmable dead-band delay is available to avoid shootthrough current from destroying the bridge power switches. The delay occurs at the signal transition from the non-active state to the active state. See Figure 15-4 for illustration. Bits PDC6:PDC0 of the PWM1CON register (Register 15-2) set the delay period in terms of microcontroller instruction cycles (TCY or 4 TOSC). These bits are not available on 28-pin devices as the standard CCP module does not support half-bridge operation. 15.4.7 ENHANCED PWM AUTO-SHUTDOWN When the CCP1 is programmed for any of the Enhanced PWM modes, the active output pins may be configured for auto-shutdown. Auto-shutdown immediately places the Enhanced PWM output pins into a defined shutdown state when a shutdown event occurs. REGISTER 15-2: A shutdown event can be caused by either of the comparator modules, a low level on the Fault input pin (FLT0) or any combination of these three sources. The comparators may be used to monitor a voltage input proportional to a current being monitored in the bridge circuit. If the voltage exceeds a threshold, the comparator switches state and triggers a shutdown. Alternatively, a low digital signal on FLT0 can also trigger a shutdown. The auto-shutdown feature can be disabled by not selecting any auto-shutdown sources. The autoshutdown sources to be used are selected using the ECCPAS2:ECCPAS0 bits (bits<6:4> of the ECCP1AS register). When a shutdown occurs, the output pins are asynchronously placed in their shutdown states, specified by the PSSAC1:PSSAC0 and PSSBD1:PSSBD0 bits (ECCPAS3:ECCPAS0). Each pin pair (P1A/P1C and P1B/P1D) may be set to drive high, drive low or be tri-stated (not driving). The ECCPASE bit (ECCPAS<7>) is also set to hold the Enhanced PWM outputs in their shutdown states. The ECCPASE bit is set by hardware when a shutdown event occurs. If automatic restarts are not enabled, the ECCPASE bit is cleared by firmware when the cause of the shutdown clears. If automatic restarts are enabled, the ECCPASE bit is automatically cleared when the cause of the auto-shutdown has cleared. If the ECCPASE bit is set when a PWM period begins, the PWM outputs remain in their shutdown state for that entire PWM period. When the ECCPASE bit is cleared, the PWM outputs will return to normal operation at the beginning of the next PWM period. Note: Writing to the ECCPASE bit is disabled while a shutdown condition is active. PWM1CON: PWM CONFIGURATION REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PRSEN PDC6(1) PDC5(1) PDC4(1) PDC3(1) PDC2(1) PDC1(1) PDC0(1) bit 7 bit 7 bit 6-0 bit 0 PRSEN: PWM Restart Enable bit 1 = Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event goes away; the PWM restarts automatically 0 = Upon auto-shutdown, ECCPASE must be cleared in software to restart the PWM PDC6:PDC0: PWM Delay Count bits(1) Delay time, in number of FOSC/4 (4 * TOSC) cycles, between the scheduled and actual time for a PWM signal to transition to active. Note 1: Unimplemented on 28-pin devices and read as `0'. Legend: R = Readable bit -n = Value at POR DS39636D-page 148 W = Writable bit `1' = Bit is set U = Unimplemented bit, read as `0' `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 15-3: ECCP1AS: ENHANCED CAPTURE/COMPARE/PWM AUTO-SHUTDOWN CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1(1) PSSBD0(1) bit 7 bit 0 bit 7 ECCPASE: ECCP Auto-Shutdown Event Status bit 1 = A shutdown event has occurred; ECCP outputs are in shutdown state 0 = ECCP outputs are operating bit 6-4 ECCPAS2:ECCPAS0: ECCP Auto-Shutdown Source Select bits 111 = FLT0 or Comparator 1 or Comparator 2 110 = FLT0 or Comparator 2 101 = FLT0 or Comparator 1 100 = FLT0 011 = Either Comparator 1 or 2 010 = Comparator 2 output 001 = Comparator 1 output 000 = Auto-shutdown is disabled bit 3-2 PSSAC1:PSSAC0: Pins A and C Shutdown State Control bits 1x = Pins A and C are tri-state (40/44-pin devices); PWM output is tri-state (28-pin devices) 01 = Drive Pins A and C to `1' 00 = Drive Pins A and C to `0' bit 1-0 PSSBD1:PSSBD0: Pins B and D Shutdown State Control bits(1) 1x = Pins B and D tri-state 01 = Drive Pins B and D to `1' 00 = Drive Pins B and D to `0' Note 1: Unimplemented on 28-pin devices and read as `0'. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 149 PIC18F2X1X/4X1X 15.4.7.1 Auto-Shutdown and Automatic Restart The auto-shutdown feature can be configured to allow automatic restarts of the module following a shutdown event. This is enabled by setting the PRSEN bit of the PWM1CON register (PWM1CON<7>). In Shutdown mode with PRSEN = 1 (Figure 15-10), the ECCPASE bit will remain set for as long as the cause of the shutdown continues. When the shutdown condition clears, the ECCP1ASE bit is cleared. If PRSEN = 0 (Figure 15-11), once a shutdown condition occurs, the ECCPASE bit will remain set until it is cleared by firmware. Once ECCPASE is cleared, the Enhanced PWM will resume at the beginning of the next PWM period. Note: Writing to the ECCPASE bit is disabled while a shutdown condition is active. Independent of the PRSEN bit setting, if the autoshutdown source is one of the comparators, the shutdown condition is a level. The ECCPASE bit cannot be cleared as long as the cause of the shutdown persists. The Auto-Shutdown mode can be forced by writing a `1' to the ECCPASE bit. FIGURE 15-10: 15.4.8 START-UP CONSIDERATIONS When the ECCP module is used in the PWM mode, the application hardware must use the proper external pullup and/or pull-down resistors on the PWM output pins. When the microcontroller is released from Reset, all of the I/O pins are in the high-impedance state. The external circuits must keep the power switch devices in the off state until the microcontroller drives the I/O pins with the proper signal levels, or activates the PWM output(s). The CCP1M1:CCP1M0 bits (CCP1CON<1:0>) allow the user to choose whether the PWM output signals are active-high or active-low for each pair of PWM output pins (P1A/P1C and P1B/P1D). The PWM output polarities must be selected before the PWM pins are configured as outputs. Changing the polarity configuration while the PWM pins are configured as outputs is not recommended, since it may result in damage to the application circuits. The P1A, P1B, P1C and P1D output latches may not be in the proper states when the PWM module is initialized. Enabling the PWM pins for output at the same time as the ECCP module may cause damage to the application circuit. The ECCP module must be enabled in the proper output mode and complete a full PWM cycle before configuring the PWM pins as outputs. The completion of a full PWM cycle is indicated by the TMR2IF bit being set as the second PWM period begins. PWM AUTO-SHUTDOWN (PRSEN = 1, AUTO-RESTART ENABLED) PWM Period PWM Activity Dead Time Duty Cycle PWM Period Dead Time Duty Cycle PWM Period Dead Time Duty Cycle Shutdown Event ECCPASE bit FIGURE 15-11: PWM AUTO-SHUTDOWN (PRSEN = 0, AUTO-RESTART DISABLED) PWM Period PWM Activity Dead Time Duty Cycle PWM Period Dead Time Duty Cycle PWM Period Dead Time Duty Cycle Shutdown Event ECCPASE bit ECCPASE Cleared by Firmware DS39636D-page 150 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 15.4.9 SETUP FOR PWM OPERATION The following steps should be taken when configuring the ECCP module for PWM operation: 1. Configure the PWM pins, P1A and P1B (and P1C and P1D, if used), as inputs by setting the corresponding TRIS bits. 2. Set the PWM period by loading the PR2 register. 3. If auto-shutdown is required: * Disable auto-shutdown (ECCP1AS = 0) * Configure source (FLT0, Comparator 1 or Comparator 2) * Wait for non-shutdown condition 4. Configure the ECCP module for the desired PWM mode and configuration by loading the CCP1CON register with the appropriate values: * Select one of the available output configurations and direction with the P1M1:P1M0 bits. * Select the polarities of the PWM output signals with the CCP1M3:CCP1M0 bits. 5. Set the PWM duty cycle by loading the CCPR1L register and CCP1CON<5:4> bits. 6. For Half-Bridge Output mode, set the deadband delay by loading ECCPDEL<6:0> with the appropriate value. 7. If auto-shutdown operation is required, load the ECCP1AS register: * Select the auto-shutdown sources using the ECCPAS2:ECCPAS0 bits. * Select the shutdown states of the PWM output pins using the PSSAC1:PSSAC0 and PSSBD1:PSSBD0 bits. * Set the ECCPASE bit (ECCPAS<7>). * Configure the comparators using the CMCON register. * Configure the comparator inputs as analog inputs. 8. If auto-restart operation is required, set the PRSEN bit (ECCPDEL<7>). 9. Configure and start TMR2: * Clear the TMR2 interrupt flag bit by clearing the TMR2IF bit (PIR1<1>). * Set the TMR2 prescale value by loading the T2CKPS bits (T2CON<1:0>). * Enable Timer2 by setting the TMR2ON bit (T2CON<2>). 10. Enable PWM outputs after a new PWM cycle has started: * Wait until TMRn overflows (TMRnIF bit is set). * Enable the CCP1/P1A, P1B, P1C and/or P1D pin outputs by clearing the respective TRIS bits. * Clear the ECCPASE bit (ECCPAS<7>). (c) 2009 Microchip Technology Inc. 15.4.10 OPERATION IN POWER-MANAGED MODES In Sleep mode, all clock sources are disabled. Timer2 will not increment and the state of the module will not change. If the ECCP pin is driving a value, it will continue to drive that value. When the device wakes up, it will continue from this state. If Two-Speed Startups are enabled, the initial start-up frequency from INTOSC and the postscaler may not be stable immediately. In PRI_IDLE mode, the primary clock will continue to clock the ECCP module without change. In all other power-managed modes, the selected power-managed mode clock will clock Timer2. Other power-managed mode clocks will most likely be different than the primary clock frequency. 15.4.10.1 Operation with Fail-Safe Clock Monitor If the Fail-Safe Clock Monitor is enabled, a clock failure will force the device into the power-managed RC_RUN mode and the OSCFIF bit (PIR2<7>) will be set. The ECCP will then be clocked from the internal oscillator clock source, which may have a different clock frequency than the primary clock. See the previous section for additional details. 15.4.11 EFFECTS OF A RESET Both Power-on Reset and subsequent Resets will force all ports to Input mode and the CCP registers to their Reset states. This forces the Enhanced CCP module to reset to a state compatible with the standard CCP module. DS39636D-page 151 PIC18F2X1X/4X1X TABLE 15-3: Name INTCON RCON REGISTERS ASSOCIATED WITH ECCP1 MODULE AND TIMER1 TO TIMER3 Bit 7 Bit 6 GIE/GIEH PEIE/GIEL IPEN SBOREN(2) Reset Values on page Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 -- RI TO PD POR BOR 50 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 PIR2 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 54 PIE2 OSCFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE 54 IPR2 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 54 TRISB PORTB Data Direction Control Register 54 TRISC PORTC Data Direction Control Register 54 TRISD PORTD Data Direction Control Register 54 TMR1L Timer1 Register Low Byte 52 TMR1H Timer1 Register High Byte 52 T1CON TMR2 T2CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON Timer2 Register -- 52 52 T2OUTPS3 T2OUTPS2 T2OUTPS1 T2OUTPS0 TMR2ON T2CKPS1 T2CKPS0 52 PR2 Timer2 Period Register 52 TMR3L Timer3 Register Low Byte 53 TMR3H Timer3 Register High Byte T3CON RD16 T3CCP2 53 T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON 53 CCPR1L Capture/Compare/PWM Register 1 Low Byte 53 CCPR1H Capture/Compare/PWM Register 1 High Byte 53 CCP1CON ECCP1AS PWM1CON Legend: Note 1: 2: P1M1 P1M0 ECCPASE ECCPAS2 PRSEN PDC6(1) DC1B1 DC1B0 CCP1M3 CCP1M2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PDC5(1) PDC4(1) PDC3(1) PDC2(1) CCP1M1 CCP1M0 PSSBD1(1) PSSBD0(1) PDC1(1) PDC0(1) 53 53 53 -- = unimplemented, read as `0'. Shaded cells are not used during ECCP operation. These bits are unimplemented on 28-pin devices and read as `0'. The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". DS39636D-page 152 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.0 16.1 MASTER SYNCHRONOUS SERIAL PORT (MSSP) MODULE MSSP Module Overview The Master Synchronous Serial Port (MSSP) module is a serial interface, useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The MSSP module can operate in one of two modes: * Serial Peripheral Interface (SPI) * Inter-Integrated Circuit (I2C) - Full Master mode - Slave mode (with general address call) 16.3 SPI Mode The SPI mode allows 8 bits of data to be synchronously transmitted and received simultaneously. All four SPI modes are supported. To accomplish communication, typically three pins are used: * Serial Data Out (SDO) - RC5/SDO * Serial Data In (SDI) - RC4/SDI/SDA * Serial Clock (SCK) - RC3/SCK/SCL Additionally, a fourth pin may be used when in a Slave mode of operation: * Slave Select (SS) - RA5/SS Figure 16-1 shows the block diagram of the MSSP module when operating in SPI mode. FIGURE 16-1: The I2C interface supports the following modes in hardware: Internal Data Bus * Master mode * Multi-Master mode * Slave mode 16.2 MSSP BLOCK DIAGRAM (SPI MODE) Read Write SSPBUF reg Control Registers The MSSP module has three associated registers. These include a status register (SSPSTAT) and two control registers (SSPCON1 and SSPCON2). The use of these registers and their individual Configuration bits differ significantly depending on whether the MSSP module is operated in SPI or I2C mode. RC4/SDI/SDA Additional details are provided under the individual sections. RA5/AN4/SS/ HLVDIN/C2OUT SSPSR reg RC5/SDO Shift Clock bit 0 SS Control Enable Edge Select 2 Clock Select RC3/SCK/ SCL SSPM3:SSPM0 SMP:CKE 4 TMR2 Output 2 2 ( Edge Select ) Prescaler TOSC 4, 16, 64 Data to TX/RX in SSPSR TRIS bit (c) 2009 Microchip Technology Inc. DS39636D-page 153 PIC18F2X1X/4X1X 16.3.1 REGISTERS The MSSP module has four registers for SPI mode operation. These are: * MSSP Control Register 1 (SSPCON1) * MSSP Status Register (SSPSTAT) * Serial Receive/Transmit Buffer Register (SSPBUF) * MSSP Shift Register (SSPSR) - Not directly accessible SSPSR is the shift register used for shifting data in or out. SSPBUF is the buffer register to which data bytes are written to or read from. In receive operations, SSPSR and SSPBUF together create a double-buffered receiver. When SSPSR receives a complete byte, it is transferred to SSPBUF and the SSPIF interrupt is set. During transmission, the SSPBUF is not doublebuffered. A write to SSPBUF will write to both SSPBUF and SSPSR. SSPCON1 and SSPSTAT are the control and status registers in SPI mode operation. The SSPCON1 register is readable and writable. The lower 6 bits of the SSPSTAT are read-only. The upper two bits of the SSPSTAT are read/write. REGISTER 16-1: SSPSTAT: MSSP STATUS REGISTER (SPI MODE) R/W-0 R/W-0 R-0 R-0 R-0 R-0 R-0 R-0 SMP CKE D/A P S R/W UA BF bit 7 bit 0 bit 7 SMP: Sample bit SPI Master mode: 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time SPI Slave mode: SMP must be cleared when SPI operation is used in Slave mode. bit 6 CKE: SPI Clock Select bit 1 = Transmit occurs on transition from active to Idle clock state 0 = Transmit occurs on transition from Idle to active clock state Note: Polarity of clock state is set by the CKP bit (SSPCON1<4>). bit 5 D/A: Data/Address bit Used in I2C mode only. bit 4 P: Stop bit Used in I2C mode only. This bit is cleared when the MSSP module is disabled; SSPEN is cleared. bit 3 S: Start bit Used in I2C mode only. bit 2 R/W: Read/Write bit Information Used in I2C mode only. bit 1 UA: Update Address bit Used in I2C mode only. bit 0 BF: Buffer Full Status bit (Receive mode only) 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Legend: DS39636D-page 154 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 16-2: SSPCON1: MSSP CONTROL REGISTER 1 (SPI MODE) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 bit 7 bit 0 bit 7 WCOL: Write Collision Detect bit (Transmit mode only) 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision bit 6 SSPOV: Receive Overflow Indicator bit SPI Slave mode: 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow (must be cleared in software). 0 = No overflow Note: bit 5 In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. SSPEN: Synchronous Serial Port Enable bit 1 = Enables serial port and configures SCK, SDO, SDI and SS as serial port pins 0 = Disables serial port and configures these pins as I/O port pins Note: When enabled, these pins must be properly configured as input or output. bit 4 CKP: Clock Polarity Select bit 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level bit 3-0 SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin 0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled 0011 = SPI Master mode, clock = TMR2 output/2 0010 = SPI Master mode, clock = FOSC/64 0001 = SPI Master mode, clock = FOSC/16 0000 = SPI Master mode, clock = FOSC/4 Note: Bit combinations not specifically listed here are either reserved or implemented in I2C mode only. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 155 PIC18F2X1X/4X1X 16.3.2 OPERATION When initializing SPI operation, several options need to be specified. This is done by programming the appropriate control bits (SSPCON1<5:0> and SSPSTAT<7:6>). These control bits allow the following to be specified: * * * * Master mode (SCK is the clock output) Slave mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Data Input Sample Phase (middle or end of data output time) * Clock Edge (output data on rising/falling edge of SCK) * Clock Rate (Master mode only) * Slave Select mode (Slave mode only) The MSSP consists of a Transmit/Receive Shift register (SSPSR) and a Buffer register (SSPBUF). The SSPSR shifts the data in and out of the device, MSb first. The SSPBUF holds the data that was written to the SSPSR until the received data is ready. Once the 8 bits of data have been received, that byte is moved to the SSPBUF register. Then, the Buffer Full detect bit, BF (SSPSTAT<0>) and the interrupt flag bit, SSPIF, are set. This double-buffering of the received data (SSPBUF) allows the next byte to start reception before EXAMPLE 16-1: LOOP reading the data that was just received. Any write to the SSPBUF register during transmission/reception of data will be ignored and the write collision detect bit, WCOL (SSPCON1<7>), will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed successfully. When the application software is expecting to receive valid data, the SSPBUF should be read before the next byte of data to transfer is written to the SSPBUF. The Buffer Full bit, BF (SSPSTAT<0>), indicates when SSPBUF has been loaded with the received data (transmission is complete). When the SSPBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI interface is only a transmitter. Generally, the MSSP interrupt is used to determine when the transmission/ reception has completed. The SSPBUF must be read and/or written. If the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. Example 16-1 shows the loading of the SSPBUF (SSPSR) for data transmission. The SSPSR is not directly readable or writable and can only be accessed by addressing the SSPBUF register. Additionally, the MSSP Status register (SSPSTAT) indicates the various status conditions. LOADING THE SSPBUF (SSPSR) REGISTER BTFSS BRA MOVF SSPSTAT, BF LOOP SSPBUF, W ;Has data been received (transmit complete)? ;No ;WREG reg = contents of SSPBUF MOVWF RXDATA ;Save in user RAM, if data is meaningful MOVF MOVWF TXDATA, W SSPBUF ;W reg = contents of TXDATA ;New data to xmit DS39636D-page 156 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.3.3 ENABLING SPI I/O 16.3.4 To enable the serial port, SSP Enable bit, SSPEN (SSPCON1<5>), must be set. To reset or reconfigure SPI mode, clear the SSPEN bit, reinitialize the SSPCON registers and then set the SSPEN bit. This configures the SDI, SDO, SCK and SS pins as serial port pins. For the pins to behave as the serial port function, some must have their data direction bits (in the TRIS register) appropriately programmed as follows: * SDI is automatically controlled by the SPI module * SDO must have TRISC<5> bit cleared * SCK (Master mode) must have TRISC<3> bit cleared * SCK (Slave mode) must have TRISC<3> bit set * SS must have TRISA<5> bit set TYPICAL CONNECTION Figure 16-2 shows a typical connection between two microcontrollers. The master controller (Processor 1) initiates the data transfer by sending the SCK signal. Data is shifted out of both shift registers on their programmed clock edge and latched on the opposite edge of the clock. Both processors should be programmed to the same Clock Polarity (CKP), then both controllers would send and receive data at the same time. Whether the data is meaningful (or dummy data) depends on the application software. This leads to three scenarios for data transmission: * Master sends data - Slave sends dummy data * Master sends data - Slave sends data * Master sends dummy data - Slave sends data Any serial port function that is not desired may be overridden by programming the corresponding Data Direction (TRIS) register to the opposite value. FIGURE 16-2: SPI MASTER/SLAVE CONNECTION SPI Master SSPM3:SSPM0 = 00xxb SPI Slave SSPM3:SSPM0 = 010xb SDO SDI Serial Input Buffer (SSPBUF) SDI Shift Register (SSPSR) MSb Serial Input Buffer (SSPBUF) LSb (c) 2009 Microchip Technology Inc. Shift Register (SSPSR) MSb SCK PROCESSOR 1 SDO Serial Clock LSb SCK PROCESSOR 2 DS39636D-page 157 PIC18F2X1X/4X1X 16.3.5 MASTER MODE The clock polarity is selected by appropriately programming the CKP bit (SSPCON1<4>). This then, would give waveforms for SPI communication as shown in Figure 16-3, Figure 16-5 and Figure 16-6, where the MSB is transmitted first. In Master mode, the SPI clock rate (bit rate) is user programmable to be one of the following: The master can initiate the data transfer at any time because it controls the SCK. The master determines when the slave (Processor 2, Figure 16-2) is to broadcast data by the software protocol. In Master mode, the data is transmitted/received as soon as the SSPBUF register is written to. If the SPI interface is only going to receive, the SDO output could be disabled (programmed as an input). The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed clock rate. As each byte is received, it will be loaded into the SSPBUF register as if a normal received byte (interrupts and status bits appropriately set). This could be useful in receiver applications as a "Line Activity Monitor" mode. FIGURE 16-3: * * * * FOSC/4 (or TCY) FOSC/16 (or 4 * TCY) FOSC/64 (or 16 * TCY) Timer2 output/2 This allows a maximum data rate (at 40 MHz) of 10.00 Mbps. Figure 16-3 shows the waveforms for Master mode. When the CKE bit is set, the SDO data is valid before there is a clock edge on SCK. The change of the input sample is shown based on the state of the SMP bit. The time when the SSPBUF is loaded with the received data is shown. SPI MODE WAVEFORM (MASTER MODE) Write to SSPBUF SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) 4 Clock Modes SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) SDO (CKE = 0) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDO (CKE = 1) bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 SDI (SMP = 0) bit 0 bit 7 Input Sample (SMP = 0) SDI (SMP = 1) bit 7 bit 0 Input Sample (SMP = 1) SSPIF SSPSR to SSPBUF DS39636D-page 158 Next Q4 Cycle after Q2 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.3.6 SLAVE MODE In Slave mode, the data is transmitted and received as the external clock pulses appear on SCK. When the last bit is latched, the SSPIF interrupt flag bit is set. Before enabling the module in SPI Slave mode, the clock line must match the proper Idle state. The clock line can be observed by reading the SCK pin. The Idle state is determined by the CKP bit (SSPCON1<4>). While in Slave mode, the external clock is supplied by the external clock source on the SCK pin. This external clock must meet the minimum high and low times as specified in the electrical specifications. While in Sleep mode, the slave can transmit/receive data. When a byte is received, the device will wake-up from Sleep. 16.3.7 SLAVE SELECT SYNCHRONIZATION The SS pin allows a Synchronous Slave mode. The SPI operation must be in Slave mode with SS pin control enabled (SSPCON1<3:0> = 04h). When the SS pin is low, transmission and reception are enabled and FIGURE 16-4: the SDO pin is driven. When the SS pin goes high, the SDO pin is no longer driven, even if in the middle of a transmitted byte and becomes a floating output. External pull-up/pull-down resistors may be desirable depending on the application. Note 1: When the SPI operation is in Slave mode with SS pin control enabled (SSPCON<3:0> = 0100), the SPI module will reset if the SS pin is set to VDD. 2: If the SPI operation is used in Slave mode with CKE set, then the SS pin control must be enabled. When the SPI module resets, the bit counter is forced to `0'. This can be done by either forcing the SS pin to a high level or clearing the SSPEN bit. To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the SPI module needs to operate as a receiver, the SDO pin can be configured as an input. This disables transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot create a bus conflict. SLAVE SYNCHRONIZATION WAVEFORM SS SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPBUF SDO SDI (SMP = 0) bit 7 bit 6 bit 7 bit 0 bit 0 bit 7 bit 7 Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF (c) 2009 Microchip Technology Inc. Next Q4 Cycle after Q2 DS39636D-page 159 PIC18F2X1X/4X1X FIGURE 16-5: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0) SS Optional SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPBUF SDO bit 7 SDI (SMP = 0) bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 bit 0 bit 7 Input Sample (SMP = 0) SSPIF Interrupt Flag Next Q4 Cycle after Q2 SSPSR to SSPBUF FIGURE 16-6: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1) SS Not Optional SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) Write to SSPBUF SDO SDI (SMP = 0) bit 6 bit 7 bit 7 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 bit 0 Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF DS39636D-page 160 Next Q4 Cycle after Q2 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.3.8 OPERATION IN POWER-MANAGED MODES 16.3.9 In SPI Master mode, module clocks may be operating at a different speed than when in full power mode. In the case of the Sleep mode, all clocks are halted. In Idle modes, a clock is provided to the peripherals. That clock should be from the primary clock source, the secondary clock (Timer1 oscillator at 32.768 kHz) or the INTOSC source. See Section 2.7 "Clock Sources and Oscillator Switching" for additional information. EFFECTS OF A RESET A Reset disables the MSSP module and terminates the current transfer. 16.3.10 BUS MODE COMPATIBILITY Table 16-1 shows the compatibility between the standard SPI modes and the states of the CKP and CKE control bits. TABLE 16-1: SPI BUS MODES Control Bits State In most cases, the speed that the master clocks SPI data is not important; however, this should be evaluated for each system. Standard SPI Mode Terminology CKP CKE If MSSP interrupts are enabled, they can wake the controller from Sleep mode, or one of the Idle modes, when the master completes sending data. If an exit from Sleep or Idle mode is not desired, MSSP interrupts should be disabled. 0, 0 0 1 0, 1 0 0 1, 0 1 1 1, 1 1 0 If the Sleep mode is selected, all module clocks are halted and the transmission/reception will remain in that state until the devices wakes. After the device returns to Run mode, the module will resume transmitting and receiving data. There is also an SMP bit which controls when the data is sampled. In SPI Slave mode, the SPI Transmit/Receive Shift register operates asynchronously to the device. This allows the device to be placed in any power-managed mode and data to be shifted into the SPI Transmit/ Receive Shift register. When all 8 bits have been received, the MSSP interrupt flag bit will be set and if enabled, will wake the device. TABLE 16-2: Name INTCON REGISTERS ASSOCIATED WITH SPI OPERATION Bit 7 Bit 6 Bit 5 GIE/GIEH PEIE/GIEL TMR0IE Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INT0IE RBIE TMR0IF INT0IF RBIF 51 PIR1 PSPIF (1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 TRISA TRISA7(2) TRISA6(2) PORTA Data Direction Control Register 54 TRISC PORTC Data Direction Control Register 54 SSPBUF SSP Receive Buffer/Transmit Register 52 SSPCON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 52 SSPSTAT SMP CKE D/A P S R/W UA BF 52 Legend: Shaded cells are not used by the MSSP in SPI mode. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. 2: PORTA<7:6> and their direction bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 161 PIC18F2X1X/4X1X 16.4 I2C Mode 16.4.1 The MSSP module in I 2C mode fully implements all master and slave functions (including general call support) and provides interrupts on Start and Stop bits in hardware to determine a free bus (multi-master function). The MSSP module implements the standard mode specifications, as well as 7-bit and 10-bit addressing. Two pins are used for data transfer: * Serial clock (SCL) - RC3/SCK/SCL * Serial data (SDA) - RC4/SDI/SDA The user must configure these pins as inputs or outputs through the TRISC<4:3> bits. FIGURE 16-7: MSSP BLOCK DIAGRAM (I2CTM MODE) Internal Data Bus Read Write SSPBUF reg RC3/SCK/SCL Shift Clock MSb LSb Match Detect Addr Match SSPADD reg Start and Stop bit Detect DS39636D-page 162 The MSSP module has six registers for I2C operation. These are: * * * * MSSP Control Register 1 (SSPCON1) MSSP Control Register 2 (SSPCON2) MSSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer Register (SSPBUF) * MSSP Shift Register (SSPSR) - Not directly accessible * MSSP Address Register (SSPADD) SSPCON1, SSPCON2 and SSPSTAT are the control and status registers in I2C mode operation. The SSPCON1 and SSPCON2 registers are readable and writable. The lower 6 bits of the SSPSTAT are read-only. The upper two bits of the SSPSTAT are read/write. SSPSR is the shift register used for shifting data in or out. SSPBUF is the buffer register to which data bytes are written to or read from. SSPADD register holds the slave device address when the SSP is configured in I2C Slave mode. When the SSP is configured in Master mode, the lower seven bits of SSPADD act as the Baud Rate Generator reload value. In receive operations, SSPSR and SSPBUF together create a double-buffered receiver. When SSPSR receives a complete byte, it is transferred to SSPBUF and the SSPIF interrupt is set. SSPSR reg RC4/SDI/ SDA REGISTERS During transmission, the SSPBUF is not doublebuffered. A write to SSPBUF will write to both SSPBUF and SSPSR. Set, Reset S, P bits (SSPSTAT reg) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 16-3: SSPSTAT: MSSP STATUS REGISTER (I2C MODE) R/W-0 R/W-0 R-0 R-0 R-0 R-0 R-0 R-0 SMP CKE D/A P S R/W UA BF bit 7 bit 0 bit 7 SMP: Slew Rate Control bit In Master or Slave mode: 1 = Slew rate control disabled for Standard Speed mode (100 kHz and 1 MHz) 0 = Slew rate control enabled for High-Speed mode (400 kHz) bit 6 CKE: SMBus Select bit In Master or Slave mode: 1 = Enable SMBus specific inputs 0 = Disable SMBus specific inputs bit 5 D/A: Data/Address bit In Master mode: Reserved. In Slave mode: 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address bit 4 P: Stop bit 1 = Indicates that a Stop bit has been detected last 0 = Stop bit was not detected last Note: bit 3 S: Start bit 1 = Indicates that a Start bit has been detected last 0 = Start bit was not detected last Note: bit 2 This bit is cleared on Reset and when SSPEN is cleared. This bit is cleared on Reset and when SSPEN is cleared. R/W: Read/Write bit Information (I2C mode only) In Slave mode: 1 = Read 0 = Write Note: This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next Start bit, Stop bit or not ACK bit. In Master mode: 1 = Transmit is in progress 0 = Transmit is not in progress Note: ORing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is in Active mode. bit 1 UA: Update Address bit (10-Bit Slave mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated bit 0 BF: Buffer Full Status bit In Transmit mode: 1 = SSPBUF is full 0 = SSPBUF is empty In Receive mode: 1 = SSPBUF is full (does not include the ACK and Stop bits) 0 = SSPBUF is empty (does not include the ACK and Stop bits) Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 163 PIC18F2X1X/4X1X REGISTER 16-4: SSPCON1: MSSP CONTROL REGISTER 1 (I2C MODE) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 bit 7 bit 0 bit 7 WCOL: Write Collision Detect bit In Master Transmit mode: 1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a transmission to be started (must be cleared in software) 0 = No collision In Slave Transmit mode: 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision In Receive mode (Master or Slave modes): This is a "don't care" bit. bit 6 SSPOV: Receive Overflow Indicator bit In Receive mode: 1 = A byte is received while the SSPBUF register is still holding the previous byte (must be cleared in software) 0 = No overflow In Transmit mode: This is a "don't care" bit in Transmit mode. bit 5 SSPEN: Synchronous Serial Port Enable bit 1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins 0 = Disables serial port and configures these pins as I/O port pins Note: When enabled, the SDA and SCL pins must be properly configured as input or output. bit 4 CKP: SCK Release Control bit In Slave mode: 1 = Release clock 0 = Holds clock low (clock stretch), used to ensure data setup time In Master mode: Unused in this mode. bit 3-0 SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled 1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled 1011 = I2C Firmware Controlled Master mode (Slave Idle) 1000 = I2C Master mode, clock = FOSC/(4 * (SSPADD + 1)) 0111 = I2C Slave mode, 10-bit address 0110 = I2C Slave mode, 7-bit address Bit combinations not specifically listed here are either reserved or implemented in SPI mode only. Legend: DS39636D-page 164 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 16-5: SSPCON2: MSSP CONTROL REGISTER 2 (I2C MODE) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 GCEN ACKSTAT ACKDT ACKEN(1) RCEN(1) PEN(1) RSEN(1) SEN(1) bit 7 bit 0 bit 7 GCEN: General Call Enable bit (Slave mode only) 1 = Enable interrupt when a general call address (0000h) is received in the SSPSR 0 = General call address disabled bit 6 ACKSTAT: Acknowledge Status bit (Master Transmit mode only) 1 = Acknowledge was not received from slave 0 = Acknowledge was received from slave bit 5 ACKDT: Acknowledge Data bit (Master Receive mode only) 1 = Not Acknowledge 0 = Acknowledge Note: Value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive. bit 4 ACKEN: Acknowledge Sequence Enable bit (Master Receive mode only)(1) 1 = Initiate Acknowledge sequence on SDA and SCL pins and transmit ACKDT data bit. Automatically cleared by hardware. 0 = Acknowledge sequence Idle bit 3 RCEN: Receive Enable bit (Master mode only)(1) 1 = Enables Receive mode for I2C operation 0 = Receive Idle bit 2 PEN: Stop Condition Enable bit (Master mode only)(1) 1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware. 0 = Stop condition Idle bit 1 RSEN: Repeated Start Condition Enable bit (Master mode only)(1) 1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware. 0 = Repeated Start condition Idle bit 0 SEN: Start Condition Enable/Stretch Enable bit(1) In Master mode: 1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware. 0 = Start condition Idle In Slave mode: 1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled) 0 = Clock stretching is disabled Note 1: For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I2C module is not in the Idle mode, these bits may not be set (no spooling) and the SSPBUF may not be written (or writes to the SSPBUF are disabled). Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 165 PIC18F2X1X/4X1X 16.4.2 OPERATION The MSSP module functions are enabled by setting MSSP Enable bit, SSPEN (SSPCON<5>). The SSPCON1 register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow one of the following I 2C modes to be selected: I2C Master mode clock I 2C Slave mode (7-bit address) I 2C Slave mode (10-bit address) I 2C Slave mode (7-bit address) with Start and Stop bit interrupts enabled * I 2C Slave mode (10-bit address) with Start and Stop bit interrupts enabled * I 2C Firmware Controlled Master mode, slave is Idle * * * * Selection of any I 2C mode with the SSPEN bit set, forces the SCL and SDA pins to be open-drain, provided these pins are programmed to inputs by setting the appropriate TRISC bits. To ensure proper operation of the module, pull-up resistors must be provided externally to the SCL and SDA pins. 16.4.3 SLAVE MODE In Slave mode, the SCL and SDA pins must be configured as inputs (TRISC<4:3> set). The MSSP module will override the input state with the output data when required (slave-transmitter). The I 2C Slave mode hardware will always generate an interrupt on an address match. Through the mode select bits, the user can also choose to interrupt on Start and Stop bits When an address is matched, or the data transfer after an address match is received, the hardware automatically will generate the Acknowledge (ACK) pulse and load the SSPBUF register with the received value currently in the SSPSR register. Any combination of the following conditions will cause the MSSP module not to give this ACK pulse: * The Buffer Full bit, BF (SSPSTAT<0>), was set before the transfer was received. * The overflow bit, SSPOV (SSPCON<6>), was set before the transfer was received. In this case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF (PIR1<3>) is set. The BF bit is cleared by reading the SSPBUF register, while bit SSPOV is cleared through software. 16.4.3.1 Addressing Once the MSSP module has been enabled, it waits for a Start condition to occur. Following the Start condition, the 8-bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match and the BF and SSPOV bits are clear, the following events occur: 1. 2. 3. 4. The SSPSR register value is loaded into the SSPBUF register. The Buffer Full bit, BF, is set. An ACK pulse is generated. MSSP Interrupt Flag bit, SSPIF (PIR1<3>), is set (interrupt is generated, if enabled) on the falling edge of the ninth SCL pulse. In 10-Bit Address mode, two address bytes need to be received by the slave. The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. Bit R/W (SSPSTAT<2>) must specify a write so the slave device will receive the second address byte. For a 10-bit address, the first byte would equal `11110 A9 A8 0', where `A9' and `A8' are the two MSbs of the address. The sequence of events for 10-bit address is as follows, with steps 7 through 9 for the slave-transmitter: 1. 2. 3. 4. 5. 6. 7. 8. 9. Receive first (high) byte of address (bits SSPIF, BF and UA (SSPSTAT<1>) are set). Update the SSPADD register with second (low) byte of address (clears bit UA and releases the SCL line). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive second (low) byte of address (bits SSPIF, BF and UA are set). Update the SSPADD register with the first (high) byte of address. If match releases SCL line, this will clear bit UA. Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive Repeated Start condition. Receive first (high) byte of address (bits SSPIF and BF are set). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. The SCL clock input must have a minimum high and low for proper operation. The high and low times of the I2C specification, as well as the requirement of the MSSP module, are shown in timing parameter 100 and parameter 101. DS39636D-page 166 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.3.2 Reception When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register and the SDA line is held low (ACK). When the address byte overflow condition exists, then the no Acknowledge (ACK) pulse is given. An overflow condition is defined as either bit BF (SSPSTAT<0>) is set, or bit SSPOV (SSPCON1<6>) is set. An MSSP interrupt is generated for each data transfer byte. Flag bit, SSPIF (PIR1<3>), must be cleared in software. The SSPSTAT register is used to determine the status of the byte. If SEN is enabled (SSPCON2<0> = 1), RC3/SCK/SCL will be held low (clock stretch) following each data transfer. The clock must be released by setting bit CKP (SSPCON<4>). See Section 16.4.4 "Clock Stretching" for more detail. 16.4.3.3 Transmission When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit and pin RC3/SCK/SCL is held low regardless of SEN (see Section 16.4.4 "Clock Stretching" for more detail). By stretching the clock, the master will be unable to assert another clock pulse until the slave is done preparing the transmit data. The transmit data must be loaded into the SSPBUF register which also loads the SSPSR register. Then pin RC3/ SCK/SCL should be enabled by setting bit CKP (SSPCON1<4>). The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 16-9). The ACK pulse from the master-receiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line is high (not ACK), then the data transfer is complete. In this case, when the ACK is latched by the slave, the slave logic is reset (resets SSPSTAT register) and the slave monitors for another occurrence of the Start bit. If the SDA line was low (ACK), the next transmit data must be loaded into the SSPBUF register. Again, pin RC3/SCK/SCL must be enabled by setting bit CKP. An MSSP interrupt is generated for each data transfer byte. The SSPIF bit must be cleared in software and the SSPSTAT register is used to determine the status of the byte. The SSPIF bit is set on the falling edge of the ninth clock pulse. (c) 2009 Microchip Technology Inc. DS39636D-page 167 DS39636D-page 168 CKP 2 A6 3 4 A4 5 A3 Receiving Address A5 6 A2 (CKP does not reset to `0' when SEN = `0') SSPOV (SSPCON1<6>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 SCL S A7 7 A1 8 9 ACK R/W = 0 1 D7 3 4 D4 5 D3 Receiving Data D5 Cleared in software SSPBUF is read 2 D6 6 D2 7 D1 8 D0 9 ACK 1 D7 2 D6 3 4 D4 5 D3 Receiving Data D5 6 D2 7 D1 8 D0 Bus master terminates transfer P SSPOV is set because SSPBUF is still full. ACK is not sent. 9 ACK FIGURE 16-8: SDA PIC18F2X1X/4X1X I2CTM SLAVE MODE TIMING WITH SEN = 0 (RECEPTION, 7-BIT ADDRESS) (c) 2009 Microchip Technology Inc. (c) 2009 Microchip Technology Inc. 1 CKP 2 A6 Data in sampled BF (SSPSTAT<0>) SSPIF (PIR1<3>) S A7 3 A5 4 A4 5 A3 6 A2 Receiving Address 7 A1 8 R/W = 0 9 ACK SCL held low while CPU responds to SSPIF 1 D7 3 D5 4 D4 5 D3 6 D2 CKP is set in software SSPBUF is written in software Cleared in software 2 D6 Transmitting Data 7 8 D0 9 ACK From SSPIF ISR D1 1 D7 4 D4 5 D3 6 D2 CKP is set in software 7 8 D0 9 ACK From SSPIF ISR D1 Transmitting Data Cleared in software 3 D5 SSPBUF is written in software 2 D6 P FIGURE 16-9: SCL SDA PIC18F2X1X/4X1X I2CTM SLAVE MODE TIMING (TRANSMISSION, 7-BIT ADDRESS) DS39636D-page 169 DS39636D-page 170 2 1 4 1 5 0 7 UA is set indicating that the SSPADD needs to be updated SSPBUF is written with contents of SSPSR 6 A9 A8 8 9 (CKP does not reset to `0' when SEN = 0) UA (SSPSTAT<1>) SSPOV (SSPCON1<6>) CKP 3 1 Cleared in software BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 SCL S 1 ACK R/W = 0 A7 2 4 A4 5 A3 6 A2 8 9 A0 ACK UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated with low byte of address 7 A1 Cleared in software 3 A5 Dummy read of SSPBUF to clear BF flag 1 A6 Receive Second Byte of Address 1 D7 4 5 6 7 D1 Cleared in software 3 D2 Cleared by hardware when SSPADD is updated with high byte of address 2 D3 Receive Data Byte D6 D5 D4 Clock is held low until update of SSPADD has taken place 8 9 1 2 4 5 6 D3 D2 Cleared in software 3 D0 ACK D7 D6 D5 D4 Receive Data Byte 7 8 D1 D0 9 P Bus master terminates transfer SSPOV is set because SSPBUF is still full. ACK is not sent. ACK FIGURE 16-10: SDA Receive First Byte of Address Clock is held low until update of SSPADD has taken place PIC18F2X1X/4X1X I2CTM SLAVE MODE TIMING WITH SEN = 0 (RECEPTION, 10-BIT ADDRESS) (c) 2009 Microchip Technology Inc. (c) 2009 Microchip Technology Inc. 2 CKP (SSPCON1<4>) UA (SSPSTAT<1>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 S SCL 1 4 1 5 0 6 7 A9 A8 8 UA is set indicating that the SSPADD needs to be updated SSPBUF is written with contents of SSPSR 3 1 Receive First Byte of Address 1 9 ACK 1 3 4 5 Cleared in software 2 7 UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated with low byte of address 6 A6 A5 A4 A3 A2 A1 8 A0 Receive Second Byte of Address Dummy read of SSPBUF to clear BF flag A7 9 ACK 2 3 1 4 1 Cleared in software 1 1 5 0 6 8 9 ACK R/W=1 1 2 4 5 6 CKP is set in software 9 P Completion of data transmission clears BF flag 8 ACK Bus master terminates transfer CKP is automatically cleared in hardware, holding SCL low 7 D4 D3 D2 D1 D0 Cleared in software 3 D7 D6 D5 Transmitting Data Byte Clock is held low until CKP is set to `1' Write of SSPBUF BF flag is clear initiates transmit at the end of the third address sequence 7 A9 A8 Cleared by hardware when SSPADD is updated with high byte of address. Dummy read of SSPBUF to clear BF flag Sr 1 Receive First Byte of Address Clock is held low until update of SSPADD has taken place FIGURE 16-11: SDA R/W = 0 Clock is held low until update of SSPADD has taken place PIC18F2X1X/4X1X I2CTM SLAVE MODE TIMING (TRANSMISSION, 10-BIT ADDRESS) DS39636D-page 171 PIC18F2X1X/4X1X 16.4.4 CLOCK STRETCHING Both 7-bit and 10-Bit Slave modes implement automatic clock stretching during a transmit sequence. The SEN bit (SSPCON2<0>) allows clock stretching to be enabled during receives. Setting SEN will cause the SCL pin to be held low at the end of each data receive sequence. 16.4.4.1 Clock Stretching for 7-Bit Slave Receive Mode (SEN = 1) In 7-Bit Slave Receive mode, on the falling edge of the ninth clock at the end of the ACK sequence if the BF bit is set, the CKP bit in the SSPCON1 register is automatically cleared, forcing the SCL output to be held low. The CKP being cleared to `0' will assert the SCL line low. The CKP bit must be set in the user's ISR before reception is allowed to continue. By holding the SCL line low, the user has time to service the ISR and read the contents of the SSPBUF before the master device can initiate another receive sequence. This will prevent buffer overruns from occurring (see Figure 16-13). Note 1: If the user reads the contents of the SSPBUF before the falling edge of the ninth clock, thus clearing the BF bit, the CKP bit will not be cleared and clock stretching will not occur. 2: The CKP bit can be set in software regardless of the state of the BF bit. The user should be careful to clear the BF bit in the ISR before the next receive sequence in order to prevent an overflow condition. 16.4.4.2 16.4.4.3 Clock Stretching for 7-Bit Slave Transmit Mode 7-Bit Slave Transmit mode implements clock stretching by clearing the CKP bit after the falling edge of the ninth clock if the BF bit is clear. This occurs regardless of the state of the SEN bit. The user's ISR must set the CKP bit before transmission is allowed to continue. By holding the SCL line low, the user has time to service the ISR and load the contents of the SSPBUF before the master device can initiate another transmit sequence (see Figure 16-9). Note 1: If the user loads the contents of SSPBUF, setting the BF bit before the falling edge of the ninth clock, the CKP bit will not be cleared and clock stretching will not occur. 2: The CKP bit can be set in software regardless of the state of the BF bit. 16.4.4.4 Clock Stretching for 10-Bit Slave Transmit Mode In 10-Bit Slave Transmit mode, clock stretching is controlled during the first two address sequences by the state of the UA bit, just as it is in 10-Bit Slave Receive mode. The first two addresses are followed by a third address sequence which contains the highorder bits of the 10-bit address and the R/W bit set to `1'. After the third address sequence is performed, the UA bit is not set, the module is now configured in Transmit mode and clock stretching is controlled by the BF flag as in 7-Bit Slave Transmit mode (see Figure 16-11). Clock Stretching for 10-Bit Slave Receive Mode (SEN = 1) In 10-Bit Slave Receive mode during the address sequence, clock stretching automatically takes place but CKP is not cleared. During this time, if the UA bit is set after the ninth clock, clock stretching is initiated. The UA bit is set after receiving the upper byte of the 10-bit address and following the receive of the second byte of the 10-bit address with the R/W bit cleared to `0'. The release of the clock line occurs upon updating SSPADD. Clock stretching will occur on each data receive sequence as described in 7-Bit Slave mode. Note: If the user polls the UA bit and clears it by updating the SSPADD register before the falling edge of the ninth clock occurs and if the user hasn't cleared the BF bit by reading the SSPBUF register before that time, then the CKP bit will still NOT be asserted low. Clock stretching on the basis of the state of the BF bit only occurs during a data sequence, not an address sequence. DS39636D-page 172 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.4.5 Clock Synchronization and the CKP bit When the CKP bit is cleared, the SCL output is forced to `0'. However, clearing the CKP bit will not assert the SCL output low until the SCL output is already sampled low. Therefore, the CKP bit will not assert the SCL line until an external I2C master device has FIGURE 16-12: already asserted the SCL line. The SCL output will remain low until the CKP bit is set and all other devices on the I2C bus have deasserted SCL. This ensures that a write to the CKP bit will not violate the minimum high time requirement for SCL (see Figure 16-12). CLOCK SYNCHRONIZATION TIMING Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 SDA DX DX - 1 SCL CKP Master device asserts clock Master device deasserts clock WR SSPCON (c) 2009 Microchip Technology Inc. DS39636D-page 173 DS39636D-page 174 CKP SSPOV (SSPCON1<6>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 SCL S A7 2 A6 3 4 A4 5 A3 Receiving Address A5 6 A2 7 A1 8 9 ACK R/W = 0 3 4 D4 5 D3 Receiving Data D5 Cleared in software 2 D6 If BF is cleared prior to the falling edge of the 9th clock, CKP will not be reset to `0' and no clock stretching will occur SSPBUF is read 1 D7 6 D2 7 D1 9 ACK 1 D7 BF is set after falling edge of the 9th clock, CKP is reset to `0' and clock stretching occurs 8 D0 CKP written to `1' in software 2 D6 Clock is held low until CKP is set to `1' 3 4 D4 5 D3 Receiving Data D5 6 D2 7 D1 8 D0 Bus master terminates transfer P SSPOV is set because SSPBUF is still full. ACK is not sent. 9 ACK Clock is not held low because ACK = 1 FIGURE 16-13: SDA Clock is not held low because buffer full bit is clear prior to falling edge of 9th clock PIC18F2X1X/4X1X I2CTM SLAVE MODE TIMING WITH SEN = 1 (RECEPTION, 7-BIT ADDRESS) (c) 2009 Microchip Technology Inc. (c) 2009 Microchip Technology Inc. 2 1 UA (SSPSTAT<1>) SSPOV (SSPCON1<6>) CKP 3 1 4 1 5 0 6 A9 7 A8 8 UA is set indicating that the SSPADD needs to be updated SSPBUF is written with contents of SSPSR Cleared in software BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 SCL S 1 9 ACK R/W = 0 A7 2 4 5 A3 6 A2 Cleared in software 3 A4 7 A1 8 A0 Note: An update of the SSPADD register before the falling edge of the ninth clock will have no effect on UA and UA will remain set. UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated with low byte of address after falling edge of ninth clock Dummy read of SSPBUF to clear BF flag 1 A6 A5 Receive Second Byte of Address 9 ACK 2 4 5 6 Cleared in software 3 D3 D2 7 D1 9 Note: An update of the SSPADD register before the falling edge of the ninth clock will have no effect on UA and UA will remain set. 8 ACK 1 4 5 6 Cleared in software 3 CKP written to `1' in software 2 D3 D2 Receive Data Byte D7 D6 D5 D4 Clock is held low until CKP is set to `1' D0 Cleared by hardware when SSPADD is updated with high byte of address after falling edge of ninth clock Dummy read of SSPBUF to clear BF flag 1 D7 D6 D5 D4 Receive Data Byte Clock is held low until update of SSPADD has taken place 7 8 9 Bus master terminates transfer P SSPOV is set because SSPBUF is still full. ACK is not sent. D1 D0 ACK Clock is not held low because ACK = 1 FIGURE 16-14: SDA Receive First Byte of Address Clock is held low until update of SSPADD has taken place PIC18F2X1X/4X1X I2CTM SLAVE MODE TIMING SEN = 1 (RECEPTION, 10-BIT ADDRESS) DS39636D-page 175 PIC18F2X1X/4X1X 16.4.5 GENERAL CALL ADDRESS SUPPORT If the general call address matches, the SSPSR is transferred to the SSPBUF, the BF flag bit is set (eighth bit) and on the falling edge of the ninth bit (ACK bit), the SSPIF interrupt flag bit is set. The addressing procedure for the I2C bus is such that the first byte after the Start condition usually determines which device will be the slave addressed by the master. The exception is the general call address which can address all devices. When this address is used, all devices should, in theory, respond with an Acknowledge. When the interrupt is serviced, the source for the interrupt can be checked by reading the contents of the SSPBUF. The value can be used to determine if the address was device specific or a general call address. In 10-Bit Address mode, the SSPADD is required to be updated for the second half of the address to match and the UA bit is set (SSPSTAT<1>). If the general call address is sampled when the GCEN bit is set, while the slave is configured in 10-Bit Address mode, then the second half of the address is not necessary, the UA bit will not be set and the slave will begin receiving data after the Acknowledge (Figure 16-15). The general call address is one of eight addresses reserved for specific purposes by the I2C protocol. It consists of all `0's with R/W = 0. The general call address is recognized when the General Call Enable bit (GCEN) is enabled (SSPCON2<7> set). Following a Start bit detect, 8 bits are shifted into the SSPSR and the address is compared against the SSPADD. It is also compared to the general call address and fixed in hardware. FIGURE 16-15: SLAVE MODE GENERAL CALL ADDRESS SEQUENCE (7 OR 10-BIT ADDRESS MODE) Address is compared to General Call Address after ACK, set interrupt SCL S 1 2 3 4 5 Receiving Data R/W = 0 General Call Address SDA ACK D7 6 7 8 9 1 ACK D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 9 SSPIF BF (SSPSTAT<0>) Cleared in software SSPBUF is read SSPOV (SSPCON1<6>) `0' GCEN (SSPCON2<7>) `1' DS39636D-page 176 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X MASTER MODE Note: Master mode is enabled by setting and clearing the appropriate SSPM bits in SSPCON1 and by setting the SSPEN bit. In Master mode, the SCL and SDA lines are manipulated by the MSSP hardware. Master mode of operation is supported by interrupt generation on the detection of the Start and Stop conditions. The Stop (P) and Start (S) bits are cleared from a Reset or when the MSSP module is disabled. Control of the I 2C bus may be taken when the P bit is set, or the bus is Idle, with both the S and P bits clear. In Firmware Controlled Master mode, user code conducts all I 2C bus operations based on Start and Stop bit conditions. 1. 2. 3. 4. 5. 6. Assert a Start condition on SDA and SCL. Assert a Repeated Start condition on SDA and SCL. Write to the SSPBUF register initiating transmission of data/address. Configure the I2C port to receive data. Generate an Acknowledge condition at the end of a received byte of data. Generate a Stop condition on SDA and SCL. FIGURE 16-16: The following events will cause the SSP Interrupt Flag bit, SSPIF, to be set (SSP interrupt, if enabled): * * * * * Once Master mode is enabled, the user has six options. The MSSP module, when configured in I2C Master mode, does not allow queueing of events. For instance, the user is not allowed to initiate a Start condition and immediately write the SSPBUF register to initiate transmission before the Start condition is complete. In this case, the SSPBUF will not be written to and the WCOL bit will be set, indicating that a write to the SSPBUF did not occur. Start condition Stop condition Data transfer byte transmitted/received Acknowledge transmit Repeated Start MSSP BLOCK DIAGRAM (I2CTM MASTER MODE) Internal Data Bus Read SSPM3:SSPM0 SSPADD<6:0> Write Baud Rate Generator SSPBUF SDA Shift Clock SDA In SCL In Bus Collision (c) 2009 Microchip Technology Inc. LSb Start bit, Stop bit, Acknowledge Generate Start bit Detect Stop bit Detect Write Collision Detect Clock Arbitration State Counter for end of XMIT/RCV Clock Cntl SCL Receive Enable SSPSR MSb Clock Arbitrate/WCOL Detect (hold off clock source) 16.4.6 Set/Reset, S, P, WCOL (SSPSTAT) Set SSPIF, BCLIF Reset ACKSTAT, PEN (SSPCON2) DS39636D-page 177 PIC18F2X1X/4X1X 16.4.6.1 I2C Master Mode Operation The master device generates all of the serial clock pulses and the Start and Stop conditions. A transfer is ended with a Stop condition or with a Repeated Start condition. Since the Repeated Start condition is also the beginning of the next serial transfer, the I2C bus will not be released. In Master Transmitter mode, serial data is output through SDA, while SCL outputs the serial clock. The first byte transmitted contains the slave address of the receiving device (7 bits) and the Read/Write (R/W) bit. In this case, the R/W bit will be logic `0'. Serial data is transmitted 8 bits at a time. After each byte is transmitted, an Acknowledge bit is received. Start and Stop conditions are output to indicate the beginning and the end of a serial transfer. In Master Receive mode, the first byte transmitted contains the slave address of the transmitting device (7 bits) and the R/W bit. In this case, the R/W bit will be logic `1'. Thus, the first byte transmitted is a 7-bit slave address followed by a `1' to indicate the receive bit. Serial data is received via SDA, while SCL outputs the serial clock. Serial data is received 8 bits at a time. After each byte is received, an Acknowledge bit is transmitted. Start and Stop conditions indicate the beginning and end of transmission. The Baud Rate Generator used for the SPI mode operation is used to set the SCL clock frequency for either 100 kHz, 400 kHz or 1 MHz I2C operation. See Section 16.4.7 "Baud Rate" for more detail. DS39636D-page 178 A typical transmit sequence would go as follows: 1. The user generates a Start condition by setting the Start Enable bit, SEN (SSPCON2<0>). 2. SSPIF is set. The MSSP module will wait the required start time before any other operation takes place. 3. The user loads the SSPBUF with the slave address to transmit. 4. Address is shifted out the SDA pin until all 8 bits are transmitted. 5. The MSSP module shifts in the ACK bit from the slave device and writes its value into the SSPCON2 register (SSPCON2<6>). 6. The MSSP module generates an interrupt at the end of the ninth clock cycle by setting the SSPIF bit. 7. The user loads the SSPBUF with eight bits of data. 8. Data is shifted out the SDA pin until all 8 bits are transmitted. 9. The MSSP module shifts in the ACK bit from the slave device and writes its value into the SSPCON2 register (SSPCON2<6>). 10. The MSSP module generates an interrupt at the end of the ninth clock cycle by setting the SSPIF bit. 11. The user generates a Stop condition by setting the Stop Enable bit, PEN (SSPCON2<2>). 12. Interrupt is generated once the Stop condition is complete. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.7 BAUD RATE 2 In I C Master mode, the Baud Rate Generator (BRG) reload value is placed in the lower 7 bits of the SSPADD register (Figure 16-17). When a write occurs to SSPBUF, the Baud Rate Generator will automatically begin counting. The BRG counts down to `0' and stops until another reload has taken place. The BRG count is decremented twice per instruction cycle (TCY) on the Q2 and Q4 clocks. In I2C Master mode, the BRG is reloaded automatically. FIGURE 16-17: Once the given operation is complete (i.e., transmission of the last data bit is followed by ACK), the internal clock will automatically stop counting and the SCL pin will remain in its last state. Table 16-3 demonstrates clock rates based on instruction cycles and the BRG value loaded into SSPADD. BAUD RATE GENERATOR BLOCK DIAGRAM SSPM3:SSPM0 SSPM3:SSPM0 Reload SCL Control CLKO TABLE 16-3: SSPADD<6:0> Reload BRG Down Counter FOSC/4 I2CTM CLOCK RATE W/BRG FOSC FCY FCY * 2 BRG Value FSCL (2 Rollovers of BRG) 40 MHz 10 MHz 20 MHz 18h 400 kHz(1) 40 MHz 10 MHz 20 MHz 1Fh 312.5 kHz 40 MHz 10 MHz 20 MHz 63h 100 kHz 16 MHz 4 MHz 8 MHz 09h 400 kHz(1) 16 MHz 4 MHz 8 MHz 0Ch 308 kHz 16 MHz 4 MHz 8 MHz 27h 100 kHz 4 MHz 1 MHz 2 MHz 02h 333 kHz(1) 4 MHz 1 MHz 2 MHz 09h 100 kHz 4 MHz 1 MHz 2 MHz 00h 1 MHz(1) Note 1: The I2C interface does not conform to the 400 kHz I2C specification (which applies to rates greater than 100 kHz) in all details, but may be used with care where higher rates are required by the application. (c) 2009 Microchip Technology Inc. DS39636D-page 179 PIC18F2X1X/4X1X 16.4.7.1 Clock Arbitration Clock arbitration occurs when the master, during any receive, transmit or Repeated Start/Stop condition, deasserts the SCL pin (SCL allowed to float high). When the SCL pin is allowed to float high, the Baud Rate Generator (BRG) is suspended from counting until the SCL pin is actually sampled high. When the FIGURE 16-18: SCL pin is sampled high, the Baud Rate Generator is reloaded with the contents of SSPADD<6:0> and begins counting. This ensures that the SCL high time will always be at least one BRG rollover count in the event that the clock is held low by an external device (Figure 16-18). BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION SDA DX DX - 1 SCL deasserted but slave holds SCL low (clock arbitration) SCL allowed to transition high SCL BRG decrements on Q2 and Q4 cycles BRG Value 03h 02h 01h 00h (hold off) 03h 02h SCL is sampled high, reload takes place and BRG starts its count BRG Reload DS39636D-page 180 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.8 I2C MASTER MODE START CONDITION TIMING Note: To initiate a Start condition, the user sets the Start Enable bit, SEN (SSPCON2<0>). If the SDA and SCL pins are sampled high, the Baud Rate Generator is reloaded with the contents of SSPADD<6:0> and starts its count. If SCL and SDA are both sampled high when the Baud Rate Generator times out (TBRG), the SDA pin is driven low. The action of the SDA being driven low while SCL is high is the Start condition and causes the S bit (SSPSTAT<3>) to be set. Following this, the Baud Rate Generator is reloaded with the contents of SSPADD<6:0> and resumes its count. When the Baud Rate Generator times out (TBRG), the SEN bit (SSPCON2<0>) will be automatically cleared by hardware; the Baud Rate Generator is suspended, leaving the SDA line held low and the Start condition is complete. FIGURE 16-19: 16.4.8.1 If at the beginning of the Start condition, the SDA and SCL pins are already sampled low, or if during the Start condition, the SCL line is sampled low before the SDA line is driven low, a bus collision occurs, the Bus Collision Interrupt Flag, BCLIF, is set, the Start condition is aborted and the I2C module is reset into its Idle state. WCOL Status Flag If the user writes the SSPBUF when a Start sequence is in progress, the WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). Note: Because queueing of events is not allowed, writing to the lower 5 bits of SSPCON2 is disabled until the Start condition is complete. FIRST START BIT TIMING Write to SEN bit occurs here Set S bit (SSPSTAT<3>) SDA = 1, SCL = 1 TBRG At completion of Start bit, hardware clears SEN bit and sets SSPIF bit TBRG Write to SSPBUF occurs here 1st bit SDA 2nd bit TBRG SCL TBRG S (c) 2009 Microchip Technology Inc. DS39636D-page 181 PIC18F2X1X/4X1X 16.4.9 I2C MASTER MODE REPEATED START CONDITION TIMING Note 1: If RSEN is programmed while any other event is in progress, it will not take effect. A Repeated Start condition occurs when the RSEN bit (SSPCON2<1>) is programmed high and the I2C logic module is in the Idle state. When the RSEN bit is set, the SCL pin is asserted low. When the SCL pin is sampled low, the Baud Rate Generator is loaded with the contents of SSPADD<5:0> and begins counting. The SDA pin is released (brought high) for one Baud Rate Generator count (TBRG). When the Baud Rate Generator times out, if SDA is sampled high, the SCL pin will be deasserted (brought high). When SCL is sampled high, the Baud Rate Generator is reloaded with the contents of SSPADD<6:0> and begins counting. SDA and SCL must be sampled high for one TBRG. This action is then followed by assertion of the SDA pin (SDA = 0) for one TBRG while SCL is high. Following this, the RSEN bit (SSPCON2<1>) will be automatically cleared and the Baud Rate Generator will not be reloaded, leaving the SDA pin held low. As soon as a Start condition is detected on the SDA and SCL pins, the S bit (SSPSTAT<3>) will be set. The SSPIF bit will not be set until the Baud Rate Generator has timed out. 2: A bus collision during the Repeated Start condition occurs if: * SDA is sampled low when SCL goes from low-to-high. * SCL goes low before SDA is asserted low. This may indicate that another master is attempting to transmit a data `1'. Immediately following the SSPIF bit getting set, the user may write the SSPBUF with the 7-bit address in 7-Bit Address mode or the default first address in 10-Bit Address mode. After the first eight bits are transmitted and an ACK is received, the user may then transmit an additional eight bits of address (10-Bit Address mode) or eight bits of data (7-Bit Address mode). 16.4.9.1 If the user writes the SSPBUF when a Repeated Start sequence is in progress, the WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). Note: FIGURE 16-20: WCOL Status Flag Because queueing of events is not allowed, writing of the lower 5 bits of SSPCON2 is disabled until the Repeated Start condition is complete. REPEAT START CONDITION WAVEFORM Write to SSPCON2 occurs here. SDA = 1, SCL (no change). S bit set by hardware SDA = 1, SCL = 1 TBRG TBRG At completion of Start bit, hardware clears RSEN bit and sets SSPIF TBRG 1st bit SDA RSEN bit set by hardware on falling edge of ninth clock, end of Xmit Write to SSPBUF occurs here TBRG SCL TBRG Sr = Repeated Start DS39636D-page 182 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.10 I2C MASTER MODE TRANSMISSION Transmission of a data byte, a 7-bit address or the other half of a 10-bit address is accomplished by simply writing a value to the SSPBUF register. This action will set the Buffer Full flag bit, BF and allow the Baud Rate Generator to begin counting and start the next transmission. Each bit of address/data will be shifted out onto the SDA pin after the falling edge of SCL is asserted (see data hold time specification parameter 106). SCL is held low for one Baud Rate Generator rollover count (TBRG). Data should be valid before SCL is released high (see data setup time specification parameter 107). When the SCL pin is released high, it is held that way for TBRG. The data on the SDA pin must remain stable for that duration and some hold time after the next falling edge of SCL. After the eighth bit is shifted out (the falling edge of the eighth clock), the BF flag is cleared and the master releases SDA. This allows the slave device being addressed to respond with an ACK bit during the ninth bit time if an address match occurred, or if data was received properly. The status of ACK is written into the ACKDT bit on the falling edge of the ninth clock. If the master receives an Acknowledge, the Acknowledge Status bit, ACKSTAT, is cleared. If not, the bit is set. After the ninth clock, the SSPIF bit is set and the master clock (Baud Rate Generator) is suspended until the next data byte is loaded into the SSPBUF, leaving SCL low and SDA unchanged (Figure 16-21). After the write to the SSPBUF, each bit of the address will be shifted out on the falling edge of SCL until all seven address bits and the R/W bit are completed. On the falling edge of the eighth clock, the master will deassert the SDA pin, allowing the slave to respond with an Acknowledge. On the falling edge of the ninth clock, the master will sample the SDA pin to see if the address was recognized by a slave. The status of the ACK bit is loaded into the ACKSTAT status bit (SSPCON2<6>). Following the falling edge of the ninth clock transmission of the address, the SSPIF is set, the BF flag is cleared and the Baud Rate Generator is turned off until another write to the SSPBUF takes place, holding SCL low and allowing SDA to float. 16.4.10.1 BF Status Flag 16.4.10.3 ACKSTAT Status Flag In Transmit mode, the ACKSTAT bit (SSPCON2<6>) is cleared when the slave has sent an Acknowledge (ACK = 0) and is set when the slave does not Acknowledge (ACK = 1). A slave sends an Acknowledge when it has recognized its address (including a general call), or when the slave has properly received its data. 16.4.11 I2C MASTER MODE RECEPTION Master mode reception is enabled by programming the Receive Enable bit, RCEN (SSPCON2<3>). Note: The MSSP module must be in an Idle state before the RCEN bit is set or the RCEN bit will be disregarded. The Baud Rate Generator begins counting and on each rollover, the state of the SCL pin changes (high-to-low/ low-to-high) and data is shifted into the SSPSR. After the falling edge of the eighth clock, the receive enable flag is automatically cleared, the contents of the SSPSR are loaded into the SSPBUF, the BF flag bit is set, the SSPIF flag bit is set and the Baud Rate Generator is suspended from counting, holding SCL low. The MSSP is now in Idle state awaiting the next command. When the buffer is read by the CPU, the BF flag bit is automatically cleared. The user can then send an Acknowledge bit at the end of reception by setting the Acknowledge Sequence Enable bit, ACKEN (SSPCON2<4>). 16.4.11.1 BF Status Flag In receive operation, the BF bit is set when an address or data byte is loaded into SSPBUF from SSPSR. It is cleared when the SSPBUF register is read. 16.4.11.2 SSPOV Status Flag In receive operation, the SSPOV bit is set when 8 bits are received into the SSPSR and the BF flag bit is already set from a previous reception. 16.4.11.3 WCOL Status Flag If the user writes the SSPBUF when a receive is already in progress (i.e., SSPSR is still shifting in a data byte), the WCOL bit is set and the contents of the buffer are unchanged (the write doesn't occur). In Transmit mode, the BF bit (SSPSTAT<0>) is set when the CPU writes to SSPBUF and is cleared when all 8 bits are shifted out. 16.4.10.2 WCOL Status Flag If the user writes the SSPBUF when a transmit is already in progress (i.e., SSPSR is still shifting out a data byte), the WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). WCOL must be cleared in software. (c) 2009 Microchip Technology Inc. DS39636D-page 183 DS39636D-page 184 S R/W PEN SEN BF (SSPSTAT<0>) SSPIF SCL SDA A6 A5 A4 A3 A2 A1 3 4 5 Cleared in software 2 6 7 8 9 After Start condition, SEN cleared by hardware SSPBUF written 1 D7 1 SCL held low while CPU responds to SSPIF ACK = `0' R/W = 0 SSPBUF written with 7-bit address and R/W, start transmit A7 Transmit Address to Slave 3 D5 4 D4 5 D3 6 D2 7 D1 8 D0 SSPBUF is written in software Cleared in software service routine from SSP interrupt 2 D6 Transmitting Data or Second Half of 10-bit Address From slave, clear ACKSTAT bit SSPCON2<6> P Cleared in software 9 ACK ACKSTAT in SSPCON2 = 1 FIGURE 16-21: SEN = 0 Write SSPCON2<0> SEN = 1 Start condition begins PIC18F2X1X/4X1X I 2CTM MASTER MODE WAVEFORM (TRANSMISSION, 7 OR 10-BIT ADDRESS) (c) 2009 Microchip Technology Inc. (c) 2009 Microchip Technology Inc. S ACKEN SSPOV BF (SSPSTAT<0>) SDA = 0, SCL = 1 while CPU responds to SSPIF SSPIF SCL SDA 1 A7 2 4 5 Cleared in software 3 6 A6 A5 A4 A3 A2 Transmit Address to Slave 7 A1 8 9 R/W = 0 ACK ACK from Slave 2 3 5 6 7 8 D0 9 ACK 2 3 4 5 6 7 Cleared in software Set SSPIF interrupt at end of Acknowledge sequence Data shifted in on falling edge of CLK 1 D7 D6 D5 D4 D3 D2 D1 Cleared in software Set SSPIF at end of receive 9 ACK is not sent ACK P Set SSPIF interrupt at end of Acknowledge sequence Bus master terminates transfer Set P bit (SSPSTAT<4>) and SSPIF PEN bit = 1 written here SSPOV is set because SSPBUF is still full 8 D0 RCEN cleared automatically Set ACKEN, start Acknowledge sequence SDA = ACKDT = 1 Receiving Data from Slave RCEN = 1, start next receive ACK from Master SDA = ACKDT = 0 Last bit is shifted into SSPSR and contents are unloaded into SSPBUF Cleared in software Set SSPIF interrupt at end of receive 4 Cleared in software 1 D7 D6 D5 D4 D3 D2 D1 Receiving Data from Slave RCEN cleared automatically Master configured as a receiver by programming SSPCON2<3> (RCEN = 1) FIGURE 16-22: SEN = 0 Write to SSPBUF occurs here, start XMIT Write to SSPCON2<0> (SEN = 1) Begin Start condition Write to SSPCON2<4> to start Acknowledge sequence SDA = ACKDT (SSPCON2<5>) = 0 PIC18F2X1X/4X1X I 2CTM MASTER MODE WAVEFORM (RECEPTION, 7-BIT ADDRESS) DS39636D-page 185 PIC18F2X1X/4X1X 16.4.12 ACKNOWLEDGE SEQUENCE TIMING 16.4.13 A Stop bit is asserted on the SDA pin at the end of a receive/transmit by setting the Stop Sequence Enable bit, PEN (SSPCON2<2>). At the end of a receive/ transmit, the SCL line is held low after the falling edge of the ninth clock. When the PEN bit is set, the master will assert the SDA line low. When the SDA line is sampled low, the Baud Rate Generator is reloaded and counts down to `0'. When the Baud Rate Generator times out, the SCL pin will be brought high and one TBRG (Baud Rate Generator rollover count) later, the SDA pin will be deasserted. When the SDA pin is sampled high while SCL is high, the P bit (SSPSTAT<4>) is set. A TBRG later, the PEN bit is cleared and the SSPIF bit is set (Figure 16-24). An Acknowledge sequence is enabled by setting the Acknowledge Sequence Enable bit, ACKEN (SSPCON2<4>). When this bit is set, the SCL pin is pulled low and the contents of the Acknowledge data bit are presented on the SDA pin. If the user wishes to generate an Acknowledge, then the ACKDT bit should be cleared. If not, the user should set the ACKDT bit before starting an Acknowledge sequence. The Baud Rate Generator then counts for one rollover period (TBRG) and the SCL pin is deasserted (pulled high). When the SCL pin is sampled high (clock arbitration), the Baud Rate Generator counts for TBRG. The SCL pin is then pulled low. Following this, the ACKEN bit is automatically cleared, the Baud Rate Generator is turned off and the MSSP module then goes into Idle mode (Figure 16-23). 16.4.12.1 16.4.13.1 WCOL Status Flag If the user writes the SSPBUF when a Stop sequence is in progress, then the WCOL bit is set and the contents of the buffer are unchanged (the write doesn't occur). WCOL Status Flag If the user writes the SSPBUF when an Acknowledge sequence is in progress, then WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). FIGURE 16-23: STOP CONDITION TIMING ACKNOWLEDGE SEQUENCE WAVEFORM Acknowledge sequence starts here, write to SSPCON2 ACKEN = 1, ACKDT = 0 SDA ACKEN automatically cleared TBRG ACK D0 SCL TBRG 8 9 SSPIF SSPIF set at the end of receive Cleared in software Cleared in software SSPIF set at the end of Acknowledge sequence Note: TBRG = one Baud Rate Generator period. FIGURE 16-24: STOP CONDITION RECEIVE OR TRANSMIT MODE SCL = 1 for TBRG, followed by SDA = 1 for TBRG after SDA sampled high. P bit (SSPSTAT<4>) is set. Write to SSPCON2, set PEN PEN bit (SSPCON2<2>) is cleared by hardware and the SSPIF bit is set Falling edge of 9th clock TBRG SCL SDA ACK P TBRG TBRG TBRG SCL brought high after TBRG SDA asserted low before rising edge of clock to setup Stop condition Note: TBRG = one Baud Rate Generator period. DS39636D-page 186 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.14 SLEEP OPERATION 16.4.17 2 While in Sleep mode, the I C module can receive addresses or data and when an address match or complete byte transfer occurs, wake the processor from Sleep (if the MSSP interrupt is enabled). 16.4.15 EFFECTS OF A RESET A Reset disables the MSSP module and terminates the current transfer. 16.4.16 MULTI-MASTER MODE In Multi-Master mode, the interrupt generation on the detection of the Start and Stop conditions allows the determination of when the bus is free. The Stop (P) and Start (S) bits are cleared from a Reset or when the MSSP module is disabled. Control of the I 2C bus may be taken when the P bit (SSPSTAT<4>) is set, or the bus is Idle, with both the S and P bits clear. When the bus is busy, enabling the SSP interrupt will generate the interrupt when the Stop condition occurs. In multi-master operation, the SDA line must be monitored for arbitration to see if the signal level is the expected output level. This check is performed in hardware with the result placed in the BCLIF bit. The states where arbitration can be lost are: * * * * * Address Transfer Data Transfer A Start Condition A Repeated Start Condition An Acknowledge Condition MULTI -MASTER COMMUNICATION, BUS COLLISION AND BUS ARBITRATION Multi-Master mode support is achieved by bus arbitration. When the master outputs address/data bits onto the SDA pin, arbitration takes place when the master outputs a `1' on SDA, by letting SDA float high and another master asserts a `0'. When the SCL pin floats high, data should be stable. If the expected data on SDA is a `1' and the data sampled on the SDA pin = 0, then a bus collision has taken place. The master will set the Bus Collision Interrupt Flag, BCLIF and reset the I2C port to its Idle state (Figure 16-25). If a transmit was in progress when the bus collision occurred, the transmission is halted, the BF flag is cleared, the SDA and SCL lines are deasserted and the SSPBUF can be written to. When the user services the bus collision Interrupt Service Routine and if the I2C bus is free, the user can resume communication by asserting a Start condition. If a Start, Repeated Start, Stop or Acknowledge condition was in progress when the bus collision occurred, the condition is aborted, the SDA and SCL lines are deasserted and the respective control bits in the SSPCON2 register are cleared. When the user services the bus collision Interrupt Service Routine and if the I2C bus is free, the user can resume communication by asserting a Start condition. The master will continue to monitor the SDA and SCL pins. If a Stop condition occurs, the SSPIF bit will be set. A write to the SSPBUF will start the transmission of data at the first data bit regardless of where the transmitter left off when the bus collision occurred. In Multi-Master mode, the interrupt generation on the detection of Start and Stop conditions allows the determination of when the bus is free. Control of the I2C bus can be taken when the P bit is set in the SSPSTAT register, or the bus is Idle and the S and P bits are cleared. FIGURE 16-25: BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE Data changes while SCL = 0 SDA line pulled low by another source SDA released by master Sample SDA. While SCL is high, data doesn't match what is driven by the master. Bus collision has occurred. SDA SCL Set bus collision interrupt (BCLIF) BCLIF (c) 2009 Microchip Technology Inc. DS39636D-page 187 PIC18F2X1X/4X1X 16.4.17.1 Bus Collision During a Start Condition During a Start condition, a bus collision occurs if: a) b) SDA or SCL are sampled low at the beginning of the Start condition (Figure 16-26). SCL is sampled low before SDA is asserted low (Figure 16-27). During a Start condition, both the SDA and the SCL pins are monitored. If the SDA pin is sampled low during this count, the BRG is reset and the SDA line is asserted early (Figure 16-28). If, however, a `1' is sampled on the SDA pin, the SDA pin is asserted low at the end of the BRG count. The Baud Rate Generator is then reloaded and counts down to 0; if the SCL pin is sampled as `0' during this time, a bus collision does not occur. At the end of the BRG count, the SCL pin is asserted low. Note: If the SDA pin is already low, or the SCL pin is already low, then all of the following occur: * the Start condition is aborted, * the BCLIF flag is set and * the MSSP module is reset to its Idle state (Figure 16-26). The Start condition begins with the SDA and SCL pins deasserted. When the SDA pin is sampled high, the Baud Rate Generator is loaded from SSPADD<6:0> and counts down to 0. If the SCL pin is sampled low while SDA is high, a bus collision occurs because it is assumed that another master is attempting to drive a data `1' during the Start condition. FIGURE 16-26: The reason that bus collision is not a factor during a Start condition is that no two bus masters can assert a Start condition at the exact same time. Therefore, one master will always assert SDA before the other. This condition does not cause a bus collision because the two masters must be allowed to arbitrate the first address following the Start condition. If the address is the same, arbitration must be allowed to continue into the data portion, Repeated Start or Stop conditions. BUS COLLISION DURING START CONDITION (SDA ONLY) SDA goes low before the SEN bit is set. Set BCLIF, S bit and SSPIF set because SDA = 0, SCL = 1. SDA SCL Set SEN, enable Start condition if SDA = 1, SCL = 1 SEN cleared automatically because of bus collision. SSP module reset into Idle state. SEN BCLIF SDA sampled low before Start condition. Set BCLIF. S bit and SSPIF set because SDA = 0, SCL = 1. SSPIF and BCLIF are cleared in software S SSPIF SSPIF and BCLIF are cleared in software DS39636D-page 188 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 16-27: BUS COLLISION DURING START CONDITION (SCL = 0) SDA = 0, SCL = 1 TBRG TBRG SDA Set SEN, enable Start sequence if SDA = 1, SCL = 1 SCL SCL = 0 before SDA = 0, bus collision occurs. Set BCLIF. SEN SCL = 0 before BRG time-out, bus collision occurs. Set BCLIF. BCLIF Interrupt cleared in software S `0' `0' SSPIF `0' `0' FIGURE 16-28: BRG RESET DUE TO SDA ARBITRATION DURING START CONDITION SDA = 0, SCL = 1 Set S Less than TBRG SDA Set SSPIF TBRG SDA pulled low by other master. Reset BRG and assert SDA. SCL S SCL pulled low after BRG time-out SEN BCLIF Set SEN, enable START sequence if SDA = 1, SCL = 1 `0' S SSPIF SDA = 0, SCL = 1, set SSPIF (c) 2009 Microchip Technology Inc. Interrupts cleared in software DS39636D-page 189 PIC18F2X1X/4X1X 16.4.17.2 Bus Collision During a Repeated Start Condition If SDA is low, a bus collision has occurred (i.e., another master is attempting to transmit a data `0', Figure 16-29). If SDA is sampled high, the BRG is reloaded and begins counting. If SDA goes from high-to-low before the BRG times out, no bus collision occurs because no two masters can assert SDA at exactly the same time. During a Repeated Start condition, a bus collision occurs if: a) b) A low level is sampled on SDA when SCL goes from low level to high level. SCL goes low before SDA is asserted low, indicating that another master is attempting to transmit a data `1'. If SCL goes from high-to-low before the BRG times out and SDA has not already been asserted, a bus collision occurs. In this case, another master is attempting to transmit a data `1' during the Repeated Start condition, see Figure 16-30. When the user deasserts SDA and the pin is allowed to float high, the BRG is loaded with SSPADD<6:0> and counts down to 0. The SCL pin is then deasserted and when sampled high, the SDA pin is sampled. FIGURE 16-29: If, at the end of the BRG time-out, both SCL and SDA are still high, the SDA pin is driven low and the BRG is reloaded and begins counting. At the end of the count, regardless of the status of the SCL pin, the SCL pin is driven low and the Repeated Start condition is complete. BUS COLLISION DURING A REPEATED START CONDITION (CASE 1) SDA SCL Sample SDA when SCL goes high. If SDA = 0, set BCLIF and release SDA and SCL. RSEN BCLIF Cleared in software `0' S `0' SSPIF FIGURE 16-30: BUS COLLISION DURING REPEATED START CONDITION (CASE 2) TBRG TBRG SDA SCL BCLIF SCL goes low before SDA, set BCLIF. Release SDA and SCL. Interrupt cleared in software RSEN S `0' SSPIF DS39636D-page 190 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 16.4.17.3 Bus Collision During a Stop Condition The Stop condition begins with SDA asserted low. When SDA is sampled low, the SCL pin is allowed to float. When the pin is sampled high (clock arbitration), the Baud Rate Generator is loaded with SSPADD<6:0> and counts down to 0. After the BRG times out, SDA is sampled. If SDA is sampled low, a bus collision has occurred. This is due to another master attempting to drive a data `0' (Figure 16-31). If the SCL pin is sampled low before SDA is allowed to float high, a bus collision occurs. This is another case of another master attempting to drive a data `0' (Figure 16-32). Bus collision occurs during a Stop condition if: a) b) After the SDA pin has been deasserted and allowed to float high, SDA is sampled low after the BRG has timed out. After the SCL pin is deasserted, SCL is sampled low before SDA goes high. FIGURE 16-31: BUS COLLISION DURING A STOP CONDITION (CASE 1) TBRG TBRG TBRG SDA SDA sampled low after TBRG, set BCLIF SDA asserted low SCL PEN BCLIF P `0' SSPIF `0' FIGURE 16-32: BUS COLLISION DURING A STOP CONDITION (CASE 2) TBRG TBRG TBRG SDA Assert SDA SCL SCL goes low before SDA goes high, set BCLIF PEN BCLIF P `0' SSPIF `0' (c) 2009 Microchip Technology Inc. DS39636D-page 191 PIC18F2X1X/4X1X NOTES: DS39636D-page 192 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 17.0 ENHANCED UNIVERSAL SYNCHRONOUS RECEIVER TRANSMITTER (EUSART) The Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) module is one of the two serial I/O modules. (Generically, the USART is also known as a Serial Communications Interface or SCI.) The EUSART can be configured as a full-duplex asynchronous system that can communicate with peripheral devices, such as CRT terminals and personal computers. It can also be configured as a halfduplex synchronous system that can communicate with peripheral devices, such as A/D or D/A integrated circuits, serial EEPROMs, etc. The Enhanced USART module implements additional features, including automatic baud rate detection and calibration, automatic wake-up on Sync Break reception and 12-bit Break character transmit. These make it ideally suited for use in Local Interconnect Network bus (LIN bus) systems. The pins of the Enhanced USART are multiplexed with PORTC. In order to configure RC6/TX/CK and RC7/RX/DT as a USART: * bit SPEN (RCSTA<7>) must be set (= 1) * bit TRISC<7> must be set (= 1) * bit TRISC<6> must be set (= 1) Note: The EUSART control will automatically reconfigure the pin from input to output as needed. The operation of the Enhanced USART module is controlled through three registers: * Transmit Status and Control (TXSTA) * Receive Status and Control (RCSTA) * Baud Rate Control (BAUDCON) These are detailed on the following pages in Register 17-1, Register 17-2 and Register 17-3, respectively. The EUSART can be configured in the following modes: * Asynchronous (full duplex) with: - Auto-wake-up on character reception - Auto-baud calibration - 12-bit Break character transmission * Synchronous - Master (half duplex) with selectable clock polarity * Synchronous - Slave (half duplex) with selectable clock polarity (c) 2009 Microchip Technology Inc. DS39636D-page 193 PIC18F2X1X/4X1X REGISTER 17-1: TXSTA: TRANSMIT STATUS AND CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-1 R/W-0 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D bit 7 bit 0 bit 7 CSRC: Clock Source Select bit Asynchronous mode: Don't care. Synchronous mode: 1 = Master mode (clock generated internally from BRG) 0 = Slave mode (clock from external source) bit 6 TX9: 9-bit Transmit Enable bit 1 = Selects 9-bit transmission 0 = Selects 8-bit transmission bit 5 TXEN: Transmit Enable bit 1 = Transmit enabled 0 = Transmit disabled Note: SREN/CREN overrides TXEN in Sync mode. bit 4 SYNC: EUSART Mode Select bit 1 = Synchronous mode 0 = Asynchronous mode bit 3 SENDB: Send Break Character bit Asynchronous mode: 1 = Send Sync Break on next transmission (cleared by hardware upon completion) 0 = Sync Break transmission completed Synchronous mode: Don't care. bit 2 BRGH: High Baud Rate Select bit Asynchronous mode: 1 = High speed 0 = Low speed Synchronous mode: Unused in this mode. bit 1 TRMT: Transmit Shift Register Status bit 1 = TSR empty 0 = TSR full bit 0 TX9D: 9th bit of Transmit Data Can be address/data bit or a parity bit. Legend: DS39636D-page 194 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 17-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-x SPEN RX9 SREN CREN ADDEN FERR OERR RX9D bit 7 bit 0 bit 7 SPEN: Serial Port Enable bit 1 = Serial port enabled (configures RX/DT and TX/CK pins as serial port pins) 0 = Serial port disabled (held in Reset) bit 6 RX9: 9-bit Receive Enable bit 1 = Selects 9-bit reception 0 = Selects 8-bit reception bit 5 SREN: Single Receive Enable bit Asynchronous mode: Don't care. Synchronous mode - Master: 1 = Enables single receive 0 = Disables single receive This bit is cleared after reception is complete. Synchronous mode - Slave: Don't care. bit 4 CREN: Continuous Receive Enable bit Asynchronous mode: 1 = Enables receiver 0 = Disables receiver Synchronous mode: 1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) 0 = Disables continuous receive bit 3 ADDEN: Address Detect Enable bit Asynchronous mode 9-bit (RX9 = 1): 1 = Enables address detection, enables interrupt and loads the receive buffer when RSR<8> is set 0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit Asynchronous mode 9-bit (RX9 = 0): Don't care. bit 2 FERR: Framing Error bit 1 = Framing error (can be updated by reading RCREG register and receiving next valid byte) 0 = No framing error bit 1 OERR: Overrun Error bit 1 = Overrun error (can be cleared by clearing bit CREN) 0 = No overrun error bit 0 RX9D: 9th bit of Received Data This can be address/data bit or a parity bit and must be calculated by user firmware. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 195 PIC18F2X1X/4X1X REGISTER 17-3: BAUDCON: BAUD RATE CONTROL REGISTER R/W-0 R-1 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 ABDOVF RCIDL -- SCKP BRG16 -- WUE ABDEN bit 7 bit 0 bit 7 ABDOVF: Auto-Baud Acquisition Rollover Status bit 1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode (must be cleared in software) 0 = No BRG rollover has occurred bit 6 RCIDL: Receive Operation Idle Status bit 1 = Receive operation is Idle 0 = Receive operation is active bit 5 Unimplemented: Read as `0' bit 4 SCKP: Synchronous Clock Polarity Select bit Asynchronous mode: Unused in this mode. Synchronous mode: 1 = Idle state for clock (CK) is a high level 0 = Idle state for clock (CK) is a low level bit 3 BRG16: 16-bit Baud Rate Register Enable bit 1 = 16-bit Baud Rate Generator - SPBRGH and SPBRG 0 = 8-bit Baud Rate Generator - SPBRG only (Compatible mode), SPBRGH value ignored bit 2 Unimplemented: Read as `0' bit 1 WUE: Wake-up Enable bit Asynchronous mode: 1 = EUSART will continue to sample the RX pin - interrupt generated on falling edge; bit cleared in hardware on following rising edge 0 = RX pin not monitored or rising edge detected Synchronous mode: Unused in this mode. bit 0 ABDEN: Auto-Baud Detect Enable bit Asynchronous mode: 1 = Enable baud rate measurement on the next character. Requires reception of a Sync field (55h); cleared in hardware upon completion 0 = Baud rate measurement disabled or completed Synchronous mode: Unused in this mode. Legend: DS39636D-page 196 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 17.1 Baud Rate Generator (BRG) The BRG is a dedicated 8-bit or 16-bit generator that supports both the Asynchronous and Synchronous modes of the EUSART. By default, the BRG operates in 8-Bit mode; setting the BRG16 bit (BAUDCON<3>) selects 16-Bit mode. The SPBRGH:SPBRG register pair controls the period of a free running timer. In Asynchronous mode, bits BRGH (TXSTA<2>) and BRG16 (BAUDCON<3>) also control the baud rate. In Synchronous mode, BRGH is ignored. Table 17-1 shows the formula for computation of the baud rate for different EUSART modes which only apply in Master mode (internally generated clock). Given the desired baud rate and FOSC, the nearest integer value for the SPBRGH:SPBRG registers can be calculated using the formulas in Table 17-1. From this, the error in baud rate can be determined. An example calculation is shown in Example 17-1. Typical baud rates and error values for the various Asynchronous modes are shown in Table 17-2. It may be TABLE 17-1: advantageous to use the high baud rate (BRGH = 1) or the 16-bit BRG to reduce the baud rate error, or achieve a slow baud rate for a fast oscillator frequency. Writing a new value to the SPBRGH:SPBRG registers causes the BRG timer to be reset (or cleared). This ensures the BRG does not wait for a timer overflow before outputting the new baud rate. 17.1.1 OPERATION IN POWER-MANAGED MODES The device clock is used to generate the desired baud rate. When one of the power-managed modes is entered, the new clock source may be operating at a different frequency. This may require an adjustment to the value in the SPBRG register pair. 17.1.2 SAMPLING The data on the RX pin is sampled three times by a majority detect circuit to determine if a high or a low level is present at the RX pin. BAUD RATE FORMULAS Configuration Bits BRG/EUSART Mode Baud Rate Formula 8-bit/Asynchronous FOSC/[64 (n + 1)] SYNC BRG16 BRGH 0 0 0 0 0 1 8-bit/Asynchronous 0 1 0 16-bit/Asynchronous 0 1 1 16-bit/Asynchronous 1 0 x 8-bit/Synchronous 1 1 x 16-bit/Synchronous FOSC/[16 (n + 1)] FOSC/[4 (n + 1)] Legend: x = Don't care, n = value of SPBRGH:SPBRG register pair EXAMPLE 17-1: CALCULATING BAUD RATE ERROR For a device with FOSC of 16 MHz, desired baud rate of 9600, Asynchronous mode, 8-bit BRG: Desired Baud Rate = FOSC/(64 ([SPBRGH:SPBRG] + 1)) Solving for SPBRGH:SPBRG: X = ((FOSC/Desired Baud Rate)/64) - 1 = ((16000000/9600)/64) - 1 = [25.042] = 25 Calculated Baud Rate = 16000000/(64 (25 + 1)) = 9615 Error = (Calculated Baud Rate - Desired Baud Rate)/Desired Baud Rate = (9615 - 9600)/9600 = 0.16% TABLE 17-2: Name REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Reset Values on page Bit 0 TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCIDL -- SCKP BRG16 -- WUE ABDEN 53 BAUDCON ABDOVF SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used by the BRG. (c) 2009 Microchip Technology Inc. DS39636D-page 197 PIC18F2X1X/4X1X TABLE 17-3: BAUD RATES FOR ASYNCHRONOUS MODES SYNC = 0, BRGH = 0, BRG16 = 0 BAUD RATE (K) FOSC = 40.000 MHz FOSC = 20.000 MHz (decimal) Actual Rate (K) % Error -- -- -- -- -- 1.221 1.73 255 2.404 Actual Rate (K) % Error 0.3 1.2 -- -- 2.4 2.441 SPBRG value FOSC = 10.000 MHz (decimal) Actual Rate (K) % Error -- 1.73 -- 255 -- 1.202 0.16 129 2.404 SPBRG value FOSC = 8.000 MHz (decimal) Actual Rate (K) % Error -- 0.16 -- 129 -- 1201 -- -0.16 -- 103 0.16 64 2403 -0.16 51 SPBRG value SPBRG value (decimal) 9.6 9.615 0.16 64 9.766 1.73 31 9.766 1.73 15 9615 -0.16 12 19.2 19.531 1.73 31 19.531 1.73 15 19.531 1.73 7 -- -- -- 57.6 56.818 -1.36 10 62.500 8.51 4 52.083 -9.58 2 -- -- -- 115.2 125.000 8.51 4 104.167 -9.58 2 78.125 -32.18 1 -- -- -- SYNC = 0, BRGH = 0, BRG16 = 0 BAUD RATE (K) FOSC = 4.000 MHz FOSC = 2.000 MHz FOSC = 1.000 MHz Actual Rate (K) % Error 207 300 -0.16 51 1201 -0.16 0.16 25 2403 -0.16 12 -- -- -- -6.99 6 -- -- -- -- -- -- 8.51 2 -- -- -- -- -- -- 8.51 0 -- -- -- -- -- -- -45.75 0 -- -- -- -- -- -- Actual Rate (K) % Error 0.3 0.300 0.16 1.2 1.202 0.16 2.4 2.404 9.6 8.929 19.2 20.833 57.6 62.500 115.2 62.500 SPBRG value (decimal) Actual Rate (K) % Error 103 300 -0.16 51 25 1201 -0.16 12 SPBRG value (decimal) SPBRG value (decimal) SYNC = 0, BRGH = 1, BRG16 = 0 BAUD RATE (K) 0.3 1.2 FOSC = 40.000 MHz Actual Rate (K) % Error -- -- -- -- FOSC = 20.000 MHz (decimal) Actual Rate (K) % Error -- -- -- -- -- -- SPBRG value SPBRG value FOSC = 10.000 MHz (decimal) Actual Rate (K) % Error -- -- -- -- FOSC = 8.000 MHz SPBRG value (decimal) Actual Rate (K) % Error SPBRG value -- -- -- -- -- -- -- -- -- -- (decimal) 2.4 -- -- -- -- -- -- 2.441 1.73 255 2403 -0.16 207 9.6 9.766 1.73 255 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51 25 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 -- -- -- SYNC = 0, BRGH = 1, BRG16 = 0 BAUD RATE (K) FOSC = 4.000 MHz FOSC = 2.000 MHz (decimal) Actual Rate (K) % Error -- -- -- 0.16 207 1201 -0.16 2.404 0.16 103 2403 9.615 0.16 25 9615 19.2 19.231 0.16 12 -- 57.6 62.500 8.51 3 115.2 125.000 8.51 1 Actual Rate (K) % Error 0.3 -- -- 1.2 1.202 2.4 9.6 DS39636D-page 198 SPBRG value FOSC = 1.000 MHz (decimal) Actual Rate (K) % Error -- 300 -0.16 207 103 1201 -0.16 51 -0.16 51 2403 -0.16 25 -0.16 12 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- SPBRG value SPBRG value (decimal) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 17-3: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED) SYNC = 0, BRGH = 0, BRG16 = 1 BAUD RATE (K) FOSC = 40.000 MHz FOSC = 20.000 MHz (decimal) Actual Rate (K) % Error 0.00 0.02 8332 2082 0.300 1.200 0.06 1040 2.399 Actual Rate (K) % Error 0.3 1.2 0.300 1.200 2.4 2.402 SPBRG value FOSC = 10.000 MHz (decimal) Actual Rate (K) % Error 0.02 -0.03 4165 1041 0.300 1.200 -0.03 520 2.404 SPBRG value FOSC = 8.000 MHz (decimal) Actual Rate (K) % Error 0.02 -0.03 2082 520 300 1201 -0.04 -0.16 1665 415 0.16 259 2403 -0.16 207 SPBRG value SPBRG value (decimal) 9.6 9.615 0.16 259 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 25 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 -- -- -- SYNC = 0, BRGH = 0, BRG16 = 1 BAUD RATE (K) FOSC = 4.000 MHz FOSC = 2.000 MHz (decimal) Actual Rate (K) % Error 832 300 -0.16 0.16 207 1201 0.16 103 2403 Actual Rate (K) % Error 0.3 0.300 0.04 1.2 1.202 2.4 2.404 SPBRG value FOSC = 1.000 MHz (decimal) Actual Rate (K) % Error 415 300 -0.16 -0.16 103 1201 -0.16 51 -0.16 51 2403 -0.16 25 SPBRG value SPBRG value (decimal) 207 9.6 9.615 0.16 25 9615 -0.16 12 -- -- -- 19.2 19.231 0.16 12 -- -- -- -- -- -- 57.6 62.500 8.51 3 -- -- -- -- -- -- 115.2 125.000 8.51 1 -- -- -- -- -- -- SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 BAUD RATE (K) FOSC = 40.000 MHz FOSC = 20.000 MHz (decimal) Actual Rate (K) % Error 0.00 33332 0.300 0.00 8332 1.200 2.400 0.02 4165 9.6 9.606 0.06 19.2 19.193 57.6 57.803 115.2 114.943 FOSC = 10.000 MHz (decimal) Actual Rate (K) % Error 0.00 16665 0.300 0.00 0.02 4165 1.200 0.02 2.400 0.02 2082 2.402 1040 9.596 -0.03 520 -0.03 520 19.231 0.16 0.35 172 57.471 -0.22 -0.22 86 116.279 0.94 Actual Rate (K) % Error 0.3 0.300 1.2 1.200 2.4 SPBRG value FOSC = 8.000 MHz Actual Rate (K) % Error 8332 300 -0.01 6665 2082 1200 -0.04 1665 0.06 1040 2400 -0.04 832 9.615 0.16 259 9615 -0.16 207 259 19.231 0.16 129 19230 -0.16 103 86 58.140 0.94 42 57142 0.79 34 42 113.636 -1.36 21 117647 -2.12 16 SPBRG value SPBRG value (decimal) SPBRG value (decimal) SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1 BAUD RATE (K) FOSC = 4.000 MHz FOSC = 2.000 MHz (decimal) Actual Rate (K) % Error 3332 300 -0.04 0.04 832 1201 2.404 0.16 415 9.615 0.16 103 19.2 19.231 0.16 57.6 58.824 115.2 111.111 FOSC = 1.000 MHz (decimal) Actual Rate (K) % Error 1665 300 -0.04 832 -0.16 415 1201 -0.16 207 2403 -0.16 207 2403 -0.16 103 9615 -0.16 51 9615 -0.16 25 51 19230 -0.16 25 19230 -0.16 12 2.12 16 55555 3.55 8 -- -- -- -3.55 8 -- -- -- -- -- -- Actual Rate (K) % Error 0.3 0.300 0.01 1.2 1.200 2.4 9.6 SPBRG value (c) 2009 Microchip Technology Inc. SPBRG value SPBRG value (decimal) DS39636D-page 199 PIC18F2X1X/4X1X 17.1.3 AUTO-BAUD RATE DETECT The Enhanced USART module supports the automatic detection and calibration of baud rate. This feature is active only in Asynchronous mode and while the WUE bit is clear. Note 1: If the WUE bit is set with the ABDEN bit, Auto-Baud Rate Detection will occur on the byte following the Break character. 2: It is up to the user to determine that the incoming character baud rate is within the range of the selected BRG clock source. Some combinations of oscillator frequency and EUSART baud rates are not possible due to bit error rates. Overall system timing and communication baud rates must be taken into consideration when using the Auto-Baud Rate Detection feature. The automatic baud rate measurement sequence (Figure 17-1) begins whenever a Start bit is received and the ABDEN bit is set. The calculation is self-averaging. In the Auto-Baud Rate Detect (ABD) mode, the clock to the BRG is reversed. Rather than the BRG clocking the incoming RX signal, the RX signal is timing the BRG. In ABD mode, the internal Baud Rate Generator is used as a counter to time the bit period of the incoming serial byte stream. Once the ABDEN bit is set, the state machine will clear the BRG and look for a Start bit. The Auto-Baud Rate Detect must receive a byte with the value 55h (ASCII "U", which is also the LIN bus Sync character) in order to calculate the proper bit rate. The measurement is taken over both a low and a high bit time in order to minimize any effects caused by asymmetry of the incoming signal. After a Start bit, the SPBRG begins counting up, using the preselected clock source on the first rising edge of RX. After eight bits on the RX pin or the fifth rising edge, an accumulated value totalling the proper BRG period is left in the SPBRGH:SPBRG register pair. Once the 5th edge is seen (this should correspond to the Stop bit), the ABDEN bit is automatically cleared. If a rollover of the BRG occurs (an overflow from FFFFh to 0000h), the event is trapped by the ABDOVF status bit (BAUDCON<7>). It is set in hardware by BRG rollovers and can be set or cleared by the user in software. ABD mode remains active after rollover events and the ABDEN bit remains set (Figure 17-2). TABLE 17-4: BRG16 BRGH BRG COUNTER CLOCK RATES BRG Counter Clock 0 0 FOSC/512 0 1 FOSC/128 1 0 FOSC/128 1 1 FOSC/32 Note: 17.1.3.1 During the ABD sequence, SPBRG and SPBRGH are both used as a 16-bit counter, independent of BRG16 setting. ABD and EUSART Transmission Since the BRG clock is reversed during ABD acquisition, the EUSART transmitter cannot be used during ABD. This means that whenever the ABDEN bit is set, TXREG cannot be written to. Users should also ensure that ABDEN does not become set during a transmit sequence. Failing to do this may result in unpredictable EUSART operation. While calibrating the baud rate period, the BRG registers are clocked at 1/8th the preconfigured clock rate. Note that the BRG clock will be configured by the BRG16 and BRGH bits. Independent of the BRG16 bit setting, both the SPBRG and SPBRGH will be used as a 16-bit counter. This allows the user to verify that no carry occurred for 8-Bit modes by checking for 00h in the SPBRGH register. Refer to Table 17-4 for counter clock rates to the BRG. While the ABD sequence takes place, the EUSART state machine is held in Idle. The RCIF interrupt is set once the fifth rising edge on RX is detected. The value in the RCREG needs to be read to clear the RCIF interrupt. The contents of RCREG should be discarded. DS39636D-page 200 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 17-1: BRG Value AUTOMATIC BAUD RATE CALCULATION XXXXh RX pin 0000h 001Ch Start Edge #1 Bit 1 Bit 0 Edge #2 Bit 3 Bit 2 Edge #3 Bit 5 Bit 4 Edge #4 Bit 7 Bit 6 Edge #5 Stop Bit BRG Clock Auto-Cleared Set by User ABDEN bit RCIF bit (Interrupt) Read RCREG SPBRG XXXXh 1Ch SPBRGH XXXXh 00h Note: The ABD sequence requires the EUSART module to be configured in Asynchronous mode and WUE = 0. FIGURE 17-2: BRG OVERFLOW SEQUENCE BRG Clock ABDEN bit RX pin Start Bit 0 ABDOVF bit FFFFh BRG Value XXXXh (c) 2009 Microchip Technology Inc. 0000h 0000h DS39636D-page 201 PIC18F2X1X/4X1X 17.2 EUSART Asynchronous Mode Once the TXREG register transfers the data to the TSR register (occurs in one TCY), the TXREG register is empty and the TXIF flag bit (PIR1<4>) is set. This interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TXIE (PIE1<4>). TXIF will be set regardless of the state of TXIE; it cannot be cleared in software. TXIF is also not cleared immediately upon loading TXREG, but becomes valid in the second instruction cycle following the load instruction. Polling TXIF immediately following a load of TXREG will return invalid results. The Asynchronous mode of operation is selected by clearing the SYNC bit (TXSTA<4>). In this mode, the EUSART uses standard Non-Return-to-Zero (NRZ) format (one Start bit, eight or nine data bits and one Stop bit). The most common data format is 8 bits. An on-chip dedicated 8-bit/16-bit Baud Rate Generator can be used to derive standard baud rate frequencies from the oscillator. The EUSART transmits and receives the LSb first. The EUSART's transmitter and receiver are functionally independent but use the same data format and baud rate. The Baud Rate Generator produces a clock, either x16 or x64 of the bit shift rate depending on the BRGH and BRG16 bits (TXSTA<2> and BAUDCON<3>). Parity is not supported by the hardware but can be implemented in software and stored as the 9th data bit. While TXIF indicates the status of the TXREG register, another bit, TRMT (TXSTA<1>), shows the status of the TSR register. TRMT is a read-only bit which is set when the TSR register is empty. No interrupt logic is tied to this bit so the user has to poll this bit in order to determine if the TSR register is empty. Note 1: The TSR register is not mapped in data memory so it is not available to the user. When operating in Asynchronous mode, the EUSART module consists of the following important elements: * * * * * * * 2: Flag bit TXIF is set when enable bit TXEN is set. Baud Rate Generator Sampling Circuit Asynchronous Transmitter Asynchronous Receiver Auto-Wake-up on Sync Break Character 12-bit Break Character Transmit Auto-Baud Rate Detection 17.2.1 To set up an Asynchronous Transmission: 1. 2. EUSART ASYNCHRONOUS TRANSMITTER 3. 4. The EUSART transmitter block diagram is shown in Figure 17-3. The heart of the transmitter is the Transmit (Serial) Shift Register (TSR). The Shift register obtains its data from the Read/Write Transmit Buffer register, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the Stop bit has been transmitted from the previous load. As soon as the Stop bit is transmitted, the TSR is loaded with new data from the TXREG register (if available). FIGURE 17-3: 5. 6. 7. 8. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRGH and BRG16 bits, as required, to achieve the desired baud rate. Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. If interrupts are desired, set enable bit TXIE. If 9-bit transmission is desired, set transmit bit TX9. Can be used as address/data bit. Enable the transmission by setting bit TXEN which will also set bit TXIF. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Load data to the TXREG register (starts transmission). If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. EUSART TRANSMIT BLOCK DIAGRAM Data Bus TXIF TXREG Register TXIE 8 MSb (8) LSb * * * Pin Buffer and Control 0 TSR Register TX pin Interrupt TXEN Baud Rate CLK TRMT BRG16 SPBRGH SPBRG Baud Rate Generator DS39636D-page 202 SPEN TX9 TX9D (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 17-4: ASYNCHRONOUS TRANSMISSION Write to TXREG Word 1 BRG Output (Shift Clock) TX (pin) Start bit bit 0 bit 1 bit 7/8 Stop bit Word 1 TXIF bit (Transmit Buffer Reg. Empty Flag) 1 TCY Word 1 Transmit Shift Reg TRMT bit (Transmit Shift Reg. Empty Flag) FIGURE 17-5: ASYNCHRONOUS TRANSMISSION (BACK TO BACK) Write to TXREG Word 1 Word 2 BRG Output (Shift Clock) TX (pin) Start bit bit 0 bit 1 1 TCY TXIF bit (Interrupt Reg. Flag) bit 7/8 Stop bit Start bit bit 0 Word 2 Word 1 1 TCY Word 1 Transmit Shift Reg. TRMT bit (Transmit Shift Reg. Empty Flag) Word 2 Transmit Shift Reg. Note: This timing diagram shows two consecutive transmissions. TABLE 17-5: Name REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCSTA TXREG TXSTA EUSART Transmit Register 53 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 BAUDCON ABDOVF RCIDL -- SCKP BRG16 -- WUE ABDEN 53 SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 Legend: -- = unimplemented locations read as `0'. Shaded cells are not used for asynchronous transmission. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 203 PIC18F2X1X/4X1X 17.2.2 EUSART ASYNCHRONOUS RECEIVER 17.2.3 The receiver block diagram is shown in Figure 17-6. The data is received on the RX pin and drives the data recovery block. The data recovery block is actually a high-speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at FOSC. This mode would typically be used in RS-232 systems. This mode would typically be used in RS-485 systems. To set up an Asynchronous Reception with Address Detect Enable: 1. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRGH and BRG16 bits, as required, to achieve the desired baud rate. 2. Enable the asynchronous serial port by clearing the SYNC bit and setting the SPEN bit. 3. If interrupts are required, set the RCEN bit and select the desired priority level with the RCIP bit. 4. Set the RX9 bit to enable 9-bit reception. 5. Set the ADDEN bit to enable address detect. 6. Enable reception by setting the CREN bit. 7. The RCIF bit will be set when reception is complete. The interrupt will be Acknowledged if the RCIE and GIE bits are set. 8. Read the RCSTA register to determine if any error occurred during reception, as well as read bit 9 of data (if applicable). 9. Read RCREG to determine if the device is being addressed. 10. If any error occurred, clear the CREN bit. 11. If the device has been addressed, clear the ADDEN bit to allow all received data into the receive buffer and interrupt the CPU. To set up an Asynchronous Reception: 1. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRGH and BRG16 bits, as required, to achieve the desired baud rate. 2. Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. 3. If interrupts are desired, set enable bit RCIE. 4. If 9-bit reception is desired, set bit RX9. 5. Enable the reception by setting bit CREN. 6. Flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable bit RCIE was set. 7. Read the RCSTA register to get the 9th bit (if enabled) and determine if any error occurred during reception. 8. Read the 8-bit received data by reading the RCREG register. 9. If any error occurred, clear the error by clearing enable bit CREN. 10. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. FIGURE 17-6: SETTING UP 9-BIT MODE WITH ADDRESS DETECT EUSART RECEIVE BLOCK DIAGRAM CREN OERR FERR x64 Baud Rate CLK BRG16 SPBRGH SPBRG Baud Rate Generator / 64 or / 16 or /4 RSR Register MSb Stop (8) 7 * * * 1 LSb 0 Start RX9 Pin Buffer and Control Data Recovery RX9D RX RCREG Register FIFO SPEN 8 Interrupt RCIF Data Bus RCIE DS39636D-page 204 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 17-7: ASYNCHRONOUS RECEPTION Start bit bit 0 RX (pin) bit 1 bit 7/8 Stop bit Rcv Shift Reg Rcv Buffer Reg Start bit bit 0 Stop bit Start bit bit 7/8 Stop bit Word 2 RCREG Word 1 RCREG Read Rcv Buffer Reg RCREG bit 7/8 RCIF (Interrupt Flag) OERR bit CREN Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word causing the OERR (overrun) bit to be set. TABLE 17-6: Name REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INT0IE RBIE TMR0IF INT0IF RBIF 51 INTCON GIE/GIEH PEIE/GIEL TMR0IE PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCSTA RCREG TXSTA EUSART Receive Register 53 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 RCIDL -- SCKP BRG16 -- WUE ABDEN 53 BAUDCON ABDOVF SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 Legend: -- = unimplemented locations read as `0'. Shaded cells are not used for asynchronous reception. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 205 PIC18F2X1X/4X1X 17.2.4 AUTO-WAKE-UP ON SYNC BREAK CHARACTER During Sleep mode, all clocks to the EUSART are suspended. Because of this, the Baud Rate Generator is inactive and a proper byte reception cannot be performed. The auto-wake-up feature allows the controller to wake-up due to activity on the RX/DT line while the EUSART is operating in Asynchronous mode. The auto-wake-up feature is enabled by setting the WUE bit (BAUDCON<1>). Once set, the typical receive sequence on RX/DT is disabled and the EUSART remains in an Idle state, monitoring for a wake-up event independent of the CPU mode. A wake-up event consists of a high-to-low transition on the RX/DT line. (This coincides with the start of a Sync Break or a Wake-up Signal character for the LIN protocol.) Following a wake-up event, the module generates an RCIF interrupt. The interrupt is generated synchronously to the Q clocks in normal operating modes (Figure 17-8) and asynchronously, if the device is in Sleep mode (Figure 17-9). The interrupt condition is cleared by reading the RCREG register. The WUE bit is automatically cleared once a low-to-high transition is observed on the RX line following the wakeup event. At this point, the EUSART module is in Idle mode and returns to normal operation. This signals to the user that the Sync Break event is over. 17.2.4.1 Special Considerations Using Auto-Wake-up Since auto-wake-up functions by sensing rising edge transitions on RX/DT, information with any state changes before the Stop bit may signal a false end-of- FIGURE 17-8: character and cause data or framing errors. To work properly, therefore, the initial character in the transmission must be all `0's. This can be 00h (8 bytes) for standard RS-232 devices or 000h (12 bits) for LIN bus. Oscillator start-up time must also be considered, especially in applications using oscillators with longer start-up intervals (i.e., XT or HS mode). The Sync Break (or Wake-up Signal) character must be of sufficient length and be followed by a sufficient interval to allow enough time for the selected oscillator to start and provide proper initialization of the EUSART. 17.2.4.2 Special Considerations Using the WUE Bit The timing of WUE and RCIF events may cause some confusion when it comes to determining the validity of received data. As noted, setting the WUE bit places the EUSART in an Idle mode. The wake-up event causes a receive interrupt by setting the RCIF bit. The WUE bit is cleared after this when a rising edge is seen on RX/DT. The interrupt condition is then cleared by reading the RCREG register. Ordinarily, the data in RCREG will be dummy data and should be discarded. The fact that the WUE bit has been cleared (or is still set) and the RCIF flag is set should not be used as an indicator of the integrity of the data in RCREG. Users should consider implementing a parallel method in firmware to verify received data integrity. To assure that no actual data is lost, check the RCIDL bit to verify that a receive operation is not in process. If a receive operation is not occurring, the WUE bit may then be set just prior to entering the Sleep mode. AUTO-WAKE-UP BIT (WUE) TIMINGS DURING NORMAL OPERATION Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 WUE bit(1) Bit set by user Auto-Cleared RX/DT Line RCIF Note 1: Cleared due to user read of RCREG The EUSART remains in Idle while the WUE bit is set. FIGURE 17-9: AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 WUE bit(2) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Bit set by user Auto-Cleared RX/DT Line Note 1 RCIF Sleep Command Executed Note 1: 2: Sleep Ends Cleared due to user read of RCREG If the wake-up event requires long oscillator warm-up time, the auto-clear of the WUE bit can occur before the oscillator is ready. This sequence should not depend on the presence of Q clocks. The EUSART remains in Idle while the WUE bit is set. DS39636D-page 206 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 17.2.5 BREAK CHARACTER SEQUENCE The EUSART module has the capability of sending the special Break character sequences that are required by the LIN bus standard. The Break character transmit consists of a Start bit, followed by twelve `0' bits and a Stop bit. The frame Break character is sent whenever the SENDB and TXEN bits (TXSTA<3> and TXSTA<5>) are set while the Transmit Shift register is loaded with data. Note that the value of data written to TXREG will be ignored and all `0's will be transmitted. The SENDB bit is automatically reset by hardware after the corresponding Stop bit is sent. This allows the user to preload the transmit FIFO with the next transmit byte following the Break character (typically, the Sync character in the LIN specification). Note that the data value written to the TXREG for the Break character is ignored. The write simply serves the purpose of initiating the proper sequence. The TRMT bit indicates when the transmit operation is active or Idle, just as it does during normal transmission. See Figure 17-10 for the timing of the Break character sequence. 17.2.5.1 Break and Sync Transmit Sequence The following sequence will send a message frame header made up of a Break, followed by an Auto-Baud Sync byte. This sequence is typical of a LIN bus master. FIGURE 17-10: Write to TXREG 1. 2. 3. 4. 5. Configure the EUSART for the desired mode. Set the TXEN and SENDB bits to set up the Break character. Load the TXREG with a dummy character to initiate transmission (the value is ignored). Write `55h' to TXREG to load the Sync character into the transmit FIFO buffer. After the Break has been sent, the SENDB bit is reset by hardware. The Sync character now transmits in the preconfigured mode. When the TXREG becomes empty, as indicated by the TXIF, the next data byte can be written to TXREG. 17.2.6 RECEIVING A BREAK CHARACTER The Enhanced USART module can receive a Break character in two ways. The first method forces configuration of the baud rate at a frequency of 9/13 the typical speed. This allows for the Stop bit transition to be at the correct sampling location (13 bits for Break versus Start bit and 8 data bits for typical data). The second method uses the auto-wake-up feature described in Section 17.2.4 "Auto-Wake-up on Sync Break Character". By enabling this feature, the EUSART will sample the next two transitions on RX/DT, cause an RCIF interrupt and receive the next data byte followed by another interrupt. Note that following a Break character, the user will typically want to enable the Auto-Baud Rate Detect feature. For both methods, the user can set the ABD bit once the TXIF interrupt is observed. SEND BREAK CHARACTER SEQUENCE Dummy Write BRG Output (Shift Clock) TX (pin) Start Bit Bit 0 Bit 1 Bit 11 Stop Bit Break TXIF bit (Transmit Buffer Reg. Empty Flag) TRMT bit (Transmit Shift Reg. Empty Flag) SENDB sampled here Auto-Cleared SENDB (Transmit Shift Reg. Empty Flag) (c) 2009 Microchip Technology Inc. DS39636D-page 207 PIC18F2X1X/4X1X 17.3 EUSART Synchronous Master Mode Once the TXREG register transfers the data to the TSR register (occurs in one TCY), the TXREG is empty and the TXIF flag bit (PIR1<4>) is set. The interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, TXIE (PIE1<4>). TXIF is set regardless of the state of enable bit TXIE; it cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. The Synchronous Master mode is entered by setting the CSRC bit (TXSTA<7>). In this mode, the data is transmitted in a half-duplex manner (i.e., transmission and reception do not occur at the same time). When transmitting data, the reception is inhibited and vice versa. Synchronous mode is entered by setting bit SYNC (TXSTA<4>). In addition, enable bit SPEN (RCSTA<7>) is set in order to configure the TX and RX pins to CK (clock) and DT (data) lines, respectively. While flag bit TXIF indicates the status of the TXREG register, another bit, TRMT (TXSTA<1>), shows the status of the TSR register. TRMT is a read-only bit which is set when the TSR is empty. No interrupt logic is tied to this bit so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not mapped in data memory so it is not available to the user. The Master mode indicates that the processor transmits the master clock on the CK line. Clock polarity is selected with the SCKP bit (BAUDCON<4>); setting SCKP sets the Idle state on CK as high, while clearing the bit sets the Idle state as low. This option is provided to support Microwire devices with this module. 17.3.1 To set up a Synchronous Master Transmission: 1. EUSART SYNCHRONOUS MASTER TRANSMISSION 2. The EUSART transmitter block diagram is shown in Figure 17-3. The heart of the transmitter is the Transmit (Serial) Shift Register (TSR). The Shift register obtains its data from the Read/Write Transmit Buffer register, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the last bit has been transmitted from the previous load. As soon as the last bit is transmitted, the TSR is loaded with new data from the TXREG (if available). FIGURE 17-11: 3. 4. 5. 6. 7. 8. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRG16 bit, as required, to achieve the desired baud rate. Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. If interrupts are desired, set enable bit TXIE. If 9-bit transmission is desired, set bit TX9. Enable the transmission by setting bit TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Start transmission by loading data to the TXREG register. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. SYNCHRONOUS TRANSMISSION Q1 Q2 Q3Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 RC7/RX/DT pin bit 0 bit 1 bit 2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 bit 7 Word 1 bit 0 bit 1 bit 7 Word 2 RC6/TX/CK pin (SCKP = 0) RC6/TX/CK pin (SCKP = 1) Write to TXREG Reg Write Word 1 Write Word 2 TXIF bit (Interrupt Flag) TRMT bit TXEN bit Note: `1' `1' Sync Master mode, SPBRG = 0, continuous transmission of two 8-bit words. DS39636D-page 208 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 17-12: SYNCHRONOUS TRANSMISSION (THROUGH TXEN) RC7/RX/DT pin bit 0 bit 1 bit 2 bit 6 bit 7 RC6/TX/CK pin Write to TXREG reg TXIF bit TRMT bit TXEN bit TABLE 17-7: Name REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INT0IE RBIE TMR0IF INT0IF RBIF 51 INTCON GIE/GIEH PEIE/GIEL TMR0IE PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCSTA TXREG EUSART Transmit Register 53 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 BAUDCON ABDOVF RCIDL -- SCKP BRG16 -- WUE ABDEN 53 SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 TXSTA Legend: -- = unimplemented, read as `0'. Shaded cells are not used for synchronous master transmission. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 209 PIC18F2X1X/4X1X 17.3.2 EUSART SYNCHRONOUS MASTER RECEPTION Once Synchronous mode is selected, reception is enabled by setting either the Single Receive Enable bit, SREN (RCSTA<5>), or the Continuous Receive Enable bit, CREN (RCSTA<4>). Data is sampled on the RX pin on the falling edge of the clock. If enable bit SREN is set, only a single word is received. If enable bit CREN is set, the reception is continuous until CREN is cleared. If both bits are set, then CREN takes precedence. To set up a Synchronous Master Reception: 1. 2. Initialize the SPBRGH:SPBRG registers for the appropriate baud rate. Set or clear the BRG16 bit, as required, to achieve the desired baud rate. Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. FIGURE 17-13: 3. 4. 5. 6. Ensure bits CREN and SREN are clear. If interrupts are desired, set enable bit RCIE. If 9-bit reception is desired, set bit RX9. If a single reception is required, set bit SREN. For continuous reception, set bit CREN. 7. Interrupt flag bit RCIF will be set when reception is complete and an interrupt will be generated if the enable bit RCIE was set. 8. Read the RCSTA register to get the 9th bit (if enabled) and determine if any error occurred during reception. 9. Read the 8-bit received data by reading the RCREG register. 10. If any error occurred, clear the error by clearing bit CREN. 11. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. SYNCHRONOUS RECEPTION (MASTER MODE, SREN) Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 RC7/RX/DT pin bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 RC7/TX/CK pin (SCKP = 0) RC7/TX/CK pin (SCKP = 1) Write to bit SREN SREN bit CREN bit `0' `0' RCIF bit (Interrupt) Read RXREG Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0. TABLE 17-8: Name REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page 51 INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCSTA RCREG TXSTA BAUDCON EUSART Receive Register 53 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 ABDOVF RCIDL -- SCKP BRG16 -- WUE ABDEN 53 SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 Legend: Note 1: -- = unimplemented, read as `0'. Shaded cells are not used for synchronous master reception. These bits are unimplemented on 28-pin devices and read as `0'. DS39636D-page 210 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 17.4 EUSART Synchronous Slave Mode To set up a Synchronous Slave Transmission: 1. Synchronous Slave mode is entered by clearing bit, CSRC (TXSTA<7>). This mode differs from the Synchronous Master mode in that the shift clock is supplied externally at the CK pin (instead of being supplied internally in Master mode). This allows the device to transfer or receive data while in any low-power mode. 17.4.1 EUSART SYNCHRONOUS SLAVE TRANSMIT 2. 3. 4. 5. 6. The operation of the Synchronous Master and Slave modes are identical, except in the case of the Sleep mode. 7. 8. If two words are written to the TXREG and then the SLEEP instruction is executed, the following will occur: a) b) c) d) e) Enable the synchronous slave serial port by setting bits SYNC and SPEN and clearing bit CSRC. Clear bits CREN and SREN. If interrupts are desired, set enable bit TXIE. If 9-bit transmission is desired, set bit TX9. Enable the transmission by setting enable bit TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Start transmission by loading data to the TXREGx register. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. The first word will immediately transfer to the TSR register and transmit. The second word will remain in the TXREG register. Flag bit TXIF will not be set. When the first word has been shifted out of TSR, the TXREG register will transfer the second word to the TSR and flag bit TXIF will now be set. If enable bit TXIE is set, the interrupt will wake the chip from Sleep. If the global interrupt is enabled, the program will branch to the interrupt vector. TABLE 17-9: Name REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INT0IE RBIE TMR0IF INT0IF RBIF 51 INTCON GIE/GIEH PEIE/GIEL TMR0IE PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCSTA TXREG TXSTA EUSART Transmit Register 53 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 RCIDL -- SCKP BRG16 -- WUE ABDEN 53 BAUDCON ABDOVF SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used for synchronous slave transmission. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 211 PIC18F2X1X/4X1X 17.4.2 EUSART SYNCHRONOUS SLAVE RECEPTION To set up a Synchronous Slave Reception: 1. The operation of the Synchronous Master and Slave modes is identical, except in the case of Sleep, or any Idle mode and bit SREN, which is a "don't care" in Slave mode. If receive is enabled by setting the CREN bit prior to entering Sleep or any Idle mode, then a word may be received while in this low-power mode. Once the word is received, the RSR register will transfer the data to the RCREG register; if the RCIE enable bit is set, the interrupt generated will wake the chip from the low-power mode. If the global interrupt is enabled, the program will branch to the interrupt vector. 2. 3. 4. 5. 6. 7. 8. 9. Enable the synchronous master serial port by setting bits SYNC and SPEN and clearing bit CSRC. If interrupts are desired, set enable bit RCIE. If 9-bit reception is desired, set bit RX9. To enable reception, set enable bit CREN. Flag bit RCIF will be set when reception is complete. An interrupt will be generated if enable bit RCIE was set. Read the RCSTA register to get the 9th bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing bit CREN. If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. TABLE 17-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 53 RCSTA RCREG TXSTA EUSART Receive Register 53 CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 53 BAUDCON ABDOVF RCIDL -- SCKP BRG16 -- WUE ABDEN 53 SPBRGH EUSART Baud Rate Generator Register, High Byte 53 SPBRG EUSART Baud Rate Generator Register, Low Byte 53 Legend: -- = unimplemented, read as `0'. Shaded cells are not used for synchronous slave reception. Note 1: These bits are unimplemented on 28-pin devices and read as `0'. DS39636D-page 212 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 18.0 10-BIT ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE The ADCON0 register, shown in Register 18-1, controls the operation of the A/D module. The ADCON1 register, shown in Register 18-2, configures the functions of the port pins. The ADCON2 register, shown in Register 18-3, configures the A/D clock source, programmed acquisition time and justification. The Analog-to-Digital (A/D) converter module has 10 inputs for the 28-pin devices and 13 for the 40/44-pin devices. This module allows conversion of an analog input signal to a corresponding 10-bit digital number. The module has five registers: * * * * * A/D Result High Register (ADRESH) A/D Result Low Register (ADRESL) A/D Control Register 0 (ADCON0) A/D Control Register 1 (ADCON1) A/D Control Register 2 (ADCON2) REGISTER 18-1: ADCON0: A/D CONTROL REGISTER 0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- CHS3 CHS2 CHS1 CHS0 GO/DONE ADON bit 7 bit 0 bit 7-6 Unimplemented: Read as `0' bit 5-2 CHS3:CHS0: Analog Channel Select bits 0000 = Channel 0 (AN0) 0001 = Channel 1 (AN1) 0010 = Channel 2 (AN2) 0011 = Channel 3 (AN3) 0100 = Channel 4 (AN4) 0101 = Channel 5 (AN5)(1,2) 0110 = Channel 6 (AN6)(1,2) 0111 = Channel 7 (AN7)(1,2) 1000 = Channel 8 (AN8) 1001 = Channel 9 (AN9) 1010 = Channel 10 (AN10) 1011 = Channel 11 (AN11) 1100 = Channel 12 (AN12 1101 = Unimplemented(2) 1110 = Unimplemented(2) 1111 = Unimplemented(2) Note 1: These channels are not implemented on 28-pin devices. 2: Performing a conversion on unimplemented channels will return a floating input measurement. bit 1 GO/DONE: A/D Conversion Status bit When ADON = 1: 1 = A/D conversion in progress 0 = A/D Idle bit 0 ADON: A/D On bit 1 = A/D converter module is enabled 0 = A/D converter module is disabled Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 213 PIC18F2X1X/4X1X REGISTER 18-2: ADCON1: A/D CONTROL REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0(1) R/W(1) R/W(1) R/W(1) -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 bit 7 bit 0 PCFG3: PCFG0 AN7(2) AN6(2) AN5(2) AN4 AN3 AN2 AN1 AN0 PCFG3:PCFG0: A/D Port Configuration Control bits: AN8 bit 3-0 AN9 VCFG0: Voltage Reference Configuration bit (VREF+ source) 1 = VREF+ (AN3) 0 = VDD AN10 bit 4 AN11 Unimplemented: Read as `0' VCFG1: Voltage Reference Configuration bit (VREF- source) 1 = VREF- (AN2) 0 = VSS AN12 bit 7-6 bit 5 0000(1) 0001 0010 0011 0100 0101 0110 A A A D D D D D A A A A D D D D A A A A A D D D A A A A A A D D A A A A A A A D A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D A D D D D D D D A A D D D D D D A A A D D D D D A A A A D D D D A A A A A D D D A A A A A A D D A A A A A A A D 0111(1) 1000 1001 1010 1011 1100 1101 1110 1111 A = Analog input Note 1: 2: D = Digital I/O The POR value of the PCFG bits depends on the value of the PBADEN Configuration bit. When PBADEN = 1, PCFG<3:0> = 0000; when PBADEN = 0, PCFG<3:0> = 0111. AN5 through AN7 are available only on 40/44-pin devices. Legend: DS39636D-page 214 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared x = Bit is unknown (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 18-3: ADCON2: A/D CONTROL REGISTER 2 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADFM -- ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 bit 7 bit 0 bit 7 ADFM: A/D Result Format Select bit 1 = Right justified 0 = Left justified bit 6 Unimplemented: Read as `0' bit 5-3 ACQT2:ACQT0: A/D Acquisition Time Select bits 111 = 20 TAD 110 = 16 TAD 101 = 12 TAD 100 = 8 TAD 011 = 6 TAD 010 = 4 TAD 001 = 2 TAD 000 = 0 TAD(1) bit 2-0 ADCS2:ADCS0: A/D Conversion Clock Select bits 111 = FRC (clock derived from A/D RC oscillator)(1) 110 = FOSC/64 101 = FOSC/16 100 = FOSC/4 011 = FRC (clock derived from A/D RC oscillator)(1) 010 = FOSC/32 001 = FOSC/8 000 = FOSC/2 Note 1: If the A/D FRC clock source is selected, a delay of one TCY (instruction cycle) is added before the A/D clock starts. This allows the SLEEP instruction to be executed before starting a conversion. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 215 PIC18F2X1X/4X1X The analog reference voltage is software selectable to either the device's positive and negative supply voltage (VDD and VSS), or the voltage level on the RA3/AN3/VREF + and RA2/AN2/VREF-/CVREF pins. A device Reset forces all registers to their Reset state. This forces the A/D module to be turned off and any conversion in progress is aborted. Each port pin associated with the A/D converter can be configured as an analog input, or as a digital I/O. The ADRESH and ADRESL registers contain the result of the A/D conversion. When the A/D conversion is complete, the result is loaded into the ADRESH:ADRESL register pair, the GO/DONE bit (ADCON0 register) is cleared and A/D Interrupt Flag bit ADIF is set. The block diagram of the A/D module is shown in Figure 18-1. The A/D converter has a unique feature of being able to operate while the device is in Sleep mode. To operate in Sleep, the A/D conversion clock must be derived from the A/D's internal RC oscillator. The output of the sample and hold is the input into the converter, which generates the result via successive approximation. FIGURE 18-1: A/D BLOCK DIAGRAM CHS3:CHS0 1100 1011 1010 1001 1000 0111 0110 0101 0100 VAIN 0011 (Input Voltage) 10-bit Converter A/D 0010 0001 VCFG1:VCFG0 0000 VDD Reference Voltage VREF+ VREF- AN12 AN11 AN10 AN9 AN8 AN7(1) AN6(1) AN5(1) AN4 AN3 AN2 AN1 AN0 X0 X1 1X 0X VSS Note 1: 2: Channels AN5 through AN7 are not available on 28-pin devices. I/O pins have diode protection to VDD and VSS. DS39636D-page 216 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X Wait for A/D conversion to complete, by either: * Polling for the GO/DONE bit to be cleared OR * Waiting for the A/D interrupt Read A/D Result registers (ADRESH:ADRESL); clear bit ADIF, if required. For next conversion, go to step 1 or step 2, as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2 TAD is required before the next acquisition starts. 6. 7. FIGURE 18-2: To perform an A/D conversion, do the following steps: FIGURE 18-3: 3FEh 003h 002h 001h 1023 LSB 1023.5 LSB 1022 LSB 1022.5 LSB 3 LSB Analog Input Voltage ANALOG INPUT MODEL VDD Rs VAIN 2 LSB 000h 2.5 LSB 3. 4. A/D TRANSFER FUNCTION 3FFh 0.5 LSB 2. Configure the A/D module: * Configure analog pins, voltage reference and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D acquisition time (ADCON2) * Select A/D conversion clock (ADCON2) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear ADIF bit * Set ADIE bit * Set GIE bit Wait the required acquisition time (if required). Start conversion: * Set GO/DONE bit (ADCON0 register) Digital Code Output 1. 1 LSB After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine acquisition time, see Section 18.1 "A/D Acquisition Requirements". After this acquisition time has elapsed, the A/D conversion can be started. An acquisition time can be programmed to occur between setting the GO/DONE bit and the actual start of the conversion. 5. 1.5 LSB The value in the ADRESH:ADRESL registers is not modified for a Power-on Reset. The ADRESH:ADRESL registers will contain unknown data after a Power-on Reset. ANx VT = 0.6V RIC 1k CPIN 5 pF Sampling Switch VT = 0.6V SS RSS ILEAKAGE 100 nA CHOLD = 25 pF VSS Legend: CPIN = input capacitance VT = threshold voltage ILEAKAGE = leakage current at the pin due to various junctions = interconnect resistance RIC = sampling switch SS = sample/hold capacitance (from DAC) CHOLD RSS = sampling switch resistance (c) 2009 Microchip Technology Inc. VDD 6V 5V 4V 3V 2V 1 2 3 4 Sampling Switch (k) DS39636D-page 217 PIC18F2X1X/4X1X 18.1 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 18-3. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD). The source impedance affects the offset voltage at the analog input (due to pin leakage current). The maximum recommended impedance for analog sources is 2.5 k. After the analog input channel is selected (changed), the channel must be sampled for at least the minimum acquisition time before starting a conversion. Note: CHOLD Rs Conversion Error VDD Temperature = = = = 25 pF 2.5 k 1/2 LSb 5V Rss = 2 k 85C (system max.) ACQUISITION TIME = Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient = TAMP + TC + TCOFF EQUATION 18-2: VHOLD or TC Example 18-3 shows the calculation of the minimum required acquisition time TACQ. This calculation is based on the following application system assumptions: When the conversion is started, the holding capacitor is disconnected from the input pin. EQUATION 18-1: TACQ To calculate the minimum acquisition time, Equation 18-1 may be used. This equation assumes that 1/2 LSb error is used (1024 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. A/D MINIMUM CHARGING TIME = (VREF - (VREF/2048)) * (1 - e(-TC/CHOLD(RIC + RSS + RS))) = -(CHOLD)(RIC + RSS + RS) ln(1/2048) EQUATION 18-3: CALCULATING THE MINIMUM REQUIRED ACQUISITION TIME TACQ = TAMP + TC + TCOFF TAMP = 0.2 s TCOFF = (Temp - 25C)(0.02 s/C) (85C - 25C)(0.02 s/C) 1.2 s Temperature coefficient is only required for temperatures > 25C. Below 25C, TCOFF = 0 ms. TC = -(CHOLD)(RIC + RSS + RS) ln(1/2047) -(25 pF) (1 k + 2 k + 2.5 k) ln(0.0004883) 1.05 s TACQ = 0.2 s + 1 s + 1.2 s 2.4 s DS39636D-page 218 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 18.2 Selecting and Configuring Acquisition Time 18.3 Selecting the A/D Conversion Clock The ADCON2 register allows the user to select an acquisition time that occurs each time the GO/DONE bit is set. It also gives users the option to use an automatically determined acquisition time. The A/D conversion time per bit is defined as TAD. The A/D conversion requires 11 TAD per 10-bit conversion. The source of the A/D conversion clock is software selectable. There are seven possible options for TAD: Acquisition time may be set with the ACQT2:ACQT0 bits (ADCON2<5:3>), which provides a range of 2 to 20 TAD. When the GO/DONE bit is set, the A/D module continues to sample the input for the selected acquisition time, then automatically begins a conversion. Since the acquisition time is programmed, there may be no need to wait for an acquisition time between selecting a channel and setting the GO/DONE bit. * * * * * * * Manual acquisition is selected when ACQT2:ACQT0 = 000. When the GO/DONE bit is set, sampling is stopped and a conversion begins. The user is responsible for ensuring the required acquisition time has passed between selecting the desired input channel and setting the GO/DONE bit. This option is also the default Reset state of the ACQT2:ACQT0 bits and is compatible with devices that do not offer programmable acquisition times. For correct A/D conversions, the A/D conversion clock (TAD) must be as short as possible, but greater than the minimum TAD (see parameter 130 for more information). 2 TOSC 4 TOSC 8 TOSC 16 TOSC 32 TOSC 64 TOSC Internal RC Oscillator Table 18-1 shows the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. In either case, when the conversion is completed, the GO/DONE bit is cleared, the ADIF flag is set and the A/D begins sampling the currently selected channel again. If an acquisition time is programmed, there is nothing to indicate if the acquisition time has ended or if the conversion has begun. TABLE 18-1: TAD vs. DEVICE OPERATING FREQUENCIES AD Clock Source (TAD) 4: PIC18LFXXXX(4) Operation ADCS2:ADCS0 PIC18FXXXX 2 TOSC 000 2.86 MHz 1.43 kHz 4 TOSC 100 5.71 MHz 2.86 MHz 8 TOSC 001 11.43 MHz 5.72 MHz 16 TOSC 101 22.86 MHz 11.43 MHz 32 TOSC 010 40.0 MHz 22.86 MHz 64 TOSC 110 40.0 MHz 22.86 MHz RC(3) Note 1: 2: 3: Maximum Device Frequency x11 1.00 MHz(1) 1.00 MHz(2) The RC source has a typical TAD time of 0.9 s. The RC source has a typical TAD time of 1.2 s. For device frequencies above 1 MHz, the device must be in Sleep for the entire conversion or the A/D accuracy may be out of specification. Low-power (PIC18LFXXXX) devices only. (c) 2009 Microchip Technology Inc. DS39636D-page 219 PIC18F2X1X/4X1X 18.4 Operation in Power-Managed Modes The selection of the automatic acquisition time and A/ D conversion clock is determined in part by the clock source and frequency while in a power-managed mode. If the A/D is expected to operate while the device is in a power-managed mode, the ACQT2:ACQT0 and ADCS2:ADCS0 bits in ADCON2 should be updated in accordance with the clock source to be used in that mode. After entering the mode, an A/D acquisition or conversion may be started. Once started, the device should continue to be clocked by the same clock source until the conversion has been completed. If desired, the device may be placed into the corresponding Idle mode during the conversion. If the device clock frequency is less than 1 MHz, the A/D RC clock source should be selected. Operation in the Sleep mode requires the A/D FRC clock to be selected. If bits ACQT2:ACQT0 are set to `000' and a conversion is started, the conversion will be delayed one instruction cycle to allow execution of the SLEEP instruction and entry to Sleep mode. The IDLEN bit (OSCCON<7>) must have already been cleared prior to starting the conversion. DS39636D-page 220 18.5 Configuring Analog Port Pins The ADCON1, TRISA, TRISB and TRISE registers all configure the A/D port pins. The port pins needed as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS3:CHS0 bits and the TRIS bits. Note 1: When reading the Port register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs will convert as analog inputs. Analog levels on a digitally configured input will be accurately converted. 2: Analog levels on any pin defined as a digital input may cause the digital input buffer to consume current out of the device's specification limits. 3: The PBADEN bit in Configuration Register 3H configures PORTB pins to reset as analog or digital pins by controlling how the PCFG0 bits in ADCON1 are reset. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 18.6 A/D Conversions After the A/D conversion is completed or aborted, a 2 TAD wait is required before the next acquisition can be started. After this wait, acquisition on the selected channel is automatically started. Figure 18-4 shows the operation of the A/D converter after the GO bit has been set and the ACQT2:ACQT0 bits are cleared. A conversion is started after the following instruction to allow entry into Sleep mode before the conversion begins. Note: Figure 18-5 shows the operation of the A/D converter after the GO bit has been set and the ACQT2:ACQT0 bits are set to `010' and selecting a 4 TAD acquisition time before the conversion starts. 18.7 Discharge The discharge phase is used to initialize the value of the capacitor array. The array is discharged before every sample. This feature helps to optimize the unitygain amplifier, as the circuit always needs to charge the capacitor array, rather than charge/discharge based on previous measure values. Clearing the GO/DONE bit during a conversion will abort the current conversion. The A/D Result register pair will NOT be updated with the partially completed A/D conversion sample. This means the ADRESH:ADRESL registers will continue to contain the value of the last completed conversion (or the last value written to the ADRESH:ADRESL registers). FIGURE 18-4: The GO/DONE bit should NOT be set in the same instruction that turns on the A/D. A/D CONVERSION TAD CYCLES (ACQT<2:0> = 000, TACQ = 0) TCY - TAD TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11 TAD1 b4 b1 b0 b6 b7 b2 b9 b8 b3 b5 Conversion starts Discharge Holding capacitor is disconnected from analog input (typically 100 ns) Set GO bit On the following cycle: ADRESH:ADRESL is loaded, GO bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. FIGURE 18-5: A/D CONVERSION TAD CYCLES (ACQT<2:0> = 010, TACQ = 4 TAD) TAD Cycles TACQT Cycles 1 2 3 Automatic Acquisition Time 4 1 2 3 4 5 6 7 8 9 10 11 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Conversion starts (Holding capacitor is disconnected) Set GO bit (Holding capacitor continues acquiring input) (c) 2009 Microchip Technology Inc. TAD1 Discharge On the following cycle: ADRESH:ADRESL is loaded, GO bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. DS39636D-page 221 PIC18F2X1X/4X1X 18.8 Use of the CCP2 Trigger An A/D conversion can be started by the special event trigger of the CCP2 module. This requires that the CCP2M3:CCP2M0 bits (CCP2CON<3:0>) be programmed as `1011' and that the A/D module is enabled (ADON bit is set). When the trigger occurs, the GO/ DONE bit will be set, starting the A/D acquisition and conversion and the Timer1 (or Timer3) counter will be reset to zero. Timer1 (or Timer3) is reset to automatically repeat the A/D acquisition period with minimal TABLE 18-2: Name software overhead (moving ADRESH:ADRESL to the desired location). The appropriate analog input channel must be selected and the minimum acquisition period is either timed by the user, or an appropriate TACQ time selected before the special event trigger sets the GO/DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), the special event trigger will be ignored by the A/D module but will still reset the Timer1 (or Timer3) counter. REGISTERS ASSOCIATED WITH A/D OPERATION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 INTCON GIE/GIEH PEIE/GIEL PIR1 PSPIF(1) ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 54 PIE1 PSPIE(1) ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 54 IPR1 PSPIP(1) ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 54 PIR2 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 54 PIE2 OSCFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE 54 IPR2 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 54 ADRESH A/D Result Register, High Byte 53 ADRESL A/D Result Register, Low Byte 53 ADCON0 -- -- CHS3 CHS2 CHS1 CHS0 GO/DONE ADON 53 ADCON1 -- -- VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 53 ADCON2 ADFM -- ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 53 PORTA RA7(1) RA6(1) RA5 RA4 RA3 RA2 RA1 RA0 54 RB1 RB0 54 TRISA PORTB TRISA7(2) TRISA6(2) PORTA Data Direction Control Register RB7 RB6 RB5 RB4 RB3 RB2 54 TRISB PORTB Data Direction Control Register 54 LATB PORTB Data Latch Register (Read and Write to Data Latch) 54 PORTE(4) -- -- -- -- RE3(3) RE2 RE1 RE0 54 TRISE IBF OBF IBOV PSPMODE -- TRISE2 TRISE1 TRISE0 54 LATE(4) -- -- -- -- -- (4) PORTE Data Latch Register 54 Legend: -- = unimplemented, read as `0'. Shaded cells are not used for A/D conversion. Note 1: These bits are unimplemented on 28-pin devices; always maintain these bits clear. 2: PORTA<7:6> and their direction bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. 3: RE3 port bit is available only as an input pin when the MCLRE Configuration bit is `0'. 4: These registers are not implemented on 28-pin devices. DS39636D-page 222 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 19.0 COMPARATOR MODULE The analog comparator module contains two comparators that can be configured in a variety of ways. The inputs can be selected from the analog inputs multiplexed with pins RA0 through RA5, as well as the on-chip voltage reference (see Section 20.0 "Comparator Voltage Reference Module"). The digital outputs (normal or inverted) are available at the pin level and can also be read through the control register. REGISTER 19-1: The CMCON register (Register 19-1) selects the comparator input and output configuration. Block diagrams of the various comparator configurations are shown in Figure 19-1. CMCON: COMPARATOR CONTROL REGISTER R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 R/W-1 C2OUT C1OUT C2INV C1INV CIS CM2 CM1 CM0 bit 7 bit 0 bit 7 C2OUT: Comparator 2 Output bit When C2INV = 0: 1 = C2 VIN+ > C2 VIN0 = C2 VIN+ < C2 VINWhen C2INV = 1: 1 = C2 VIN+ < C2 VIN0 = C2 VIN+ > C2 VIN- bit 6 C1OUT: Comparator 1 Output bit When C1INV = 0: 1 = C1 VIN+ > C1 VIN0 = C1 VIN+ < C1 VINWhen C1INV = 1: 1 = C1 VIN+ < C1 VIN0 = C1 VIN+ > C1 VIN- bit 5 C2INV: Comparator 2 Output Inversion bit 1 = C2 output inverted 0 = C2 output not inverted bit 4 C1INV: Comparator 1 Output Inversion bit 1 = C1 output inverted 0 = C1 output not inverted bit 3 CIS: Comparator Input Switch bit When CM2:CM0 = 110: 1 = C1 VIN+ connects to RA3/AN3/VREF+ C2 VIN+ connects to RA2/AN2/VREF-/CVREF 0 = C1 VIN- connects to RA0/AN0 C2 VIN- connects to RA1/AN1 bit 2-0 CM2:CM0: Comparator Mode bits Figure 19-1 shows the Comparator modes and the CM2:CM0 bit settings. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 223 PIC18F2X1X/4X1X 19.1 Comparator Configuration There are eight modes of operation for the comparators, shown in Figure 19-1. Bits CM2:CM0 of the CMCON register are used to select these modes. The TRISA register controls the data direction of the comparator pins for each mode. If the Comparator mode is FIGURE 19-1: VIN- RA3/AN3/ A VREF+ VIN+ A VIN- RA2/AN2/ A VREF-/CVREF VIN+ C1 Off (Read as `0') C2 Off (Read as `0') Two Independent Comparators CM2:CM0 = 010 A VIN- RA3/AN3/ A VREF+ VIN+ A VIN- RA2/AN2/ A VREF-/CVREF VIN+ RA0/AN0 Comparator interrupts should be disabled during a Comparator mode change; otherwise, a false interrupt may occur. Comparators Off (POR Default Value) CM2:CM0 = 111 A RA1/AN1 Note: COMPARATOR I/O OPERATING MODES Comparators Reset CM2:CM0 = 000 RA0/AN0 changed, the comparator output level may not be valid for the specified mode change delay shown in Section 25.0 "Electrical Characteristics". C1 RA0/AN0 D VIN- RA3/AN3/ VREF+ D VIN+ RA1/AN1 D VIN- D RA2/AN2/ VREF-/CVREF VIN+ C1 Off (Read as `0') C2 Off (Read as `0') Two Independent Comparators with Outputs CM2:CM0 = 011 C1OUT RA0/AN0 RA3/AN3/ VREF+ A VIN- A VIN+ C1 C1OUT C2 C2OUT RA4/T0CKI/C1OUT* RA1/AN1 C2 C2OUT A VIN- RA2/AN2/ A VREF-/CVREF VIN+ RA1/AN1 RA5/AN4/SS/HLVDIN/C2OUT* Two Common Reference Comparators CM2:CM0 = 100 A VIN- RA3/AN3/ A VREF+ VIN+ A VIN- RA2/AN2/ D VREF-/CVREF VIN+ RA0/AN0 C1 Two Common Reference Comparators with Outputs CM2:CM0 = 101 C1OUT RA0/AN0 RA3/AN3/ VREF+ A VIN- A VIN+ C1 C1OUT C2 C2OUT RA4/T0CKI/C1OUT* RA1/AN1 C2 C2OUT A VIN- RA2/AN2/ D VREF-/CVREF VIN+ RA1/AN1 RA5/AN4/SS/HLVDIN/C2OUT* One Independent Comparator with Output CM2:CM0 = 001 A VIN- RA3/AN3/ A VREF+ VIN+ RA0/AN0 C1 C1OUT RA4/T0CKI/C1OUT* D VIN- RA2/AN2/ D VREF-/CVREF VIN+ RA1/AN1 Four Inputs Multiplexed to Two Comparators CM2:CM0 = 110 RA0/AN0 A RA3/AN3/ VREF+ A RA1/AN1 A A RA2/AN2/ VREF-/CVREF C2 Off (Read as `0') CIS = 0 CIS = 1 VIN- CIS = 0 CIS = 1 VIN- VIN+ VIN+ C1 C1OUT C2 C2OUT CVREF From VREF Module A = Analog Input, port reads zeros always D = Digital Input CIS (CMCON<3>) is the Comparator Input Switch * Setting the TRISA<5:4> bits will disable the comparator outputs by configuring the pins as inputs. DS39636D-page 224 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 19.2 Comparator Operation 19.3.2 A single comparator is shown in Figure 19-2, along with the relationship between the analog input levels and the digital output. When the analog input at VIN+ is less than the analog input VIN-, the output of the comparator is a digital low level. When the analog input at VIN+ is greater than the analog input VIN-, the output of the comparator is a digital high level. The shaded areas of the output of the comparator in Figure 19-2 represent the uncertainty, due to input offsets and response time. 19.3 Comparator Reference Depending on the comparator operating mode, either an external or internal voltage reference may be used. The analog signal present at VIN- is compared to the signal at VIN+ and the digital output of the comparator is adjusted accordingly (Figure 19-2). FIGURE 19-2: SINGLE COMPARATOR VIN+ + VIN- - Output VINVIN+ Output 19.3.1 INTERNAL REFERENCE SIGNAL The comparator module also allows the selection of an internally generated voltage reference from the comparator voltage reference module. This module is described in more detail in Section 20.0 "Comparator Voltage Reference Module". The internal reference is only available in the mode where four inputs are multiplexed to two comparators (CM2:CM0 = 110). In this mode, the internal voltage reference is applied to the VIN+ pin of both comparators. 19.4 Comparator Response Time Response time is the minimum time, after selecting a new reference voltage or input source, before the comparator output has a valid level. If the internal reference is changed, the maximum delay of the internal voltage reference must be considered when using the comparator outputs. Otherwise, the maximum delay of the comparators should be used (see Section 25.0 "Electrical Characteristics"). 19.5 Comparator Outputs The comparator outputs are read through the CMCON register. These bits are read-only. The comparator outputs may also be directly output to the RA4 and RA5 I/O pins. When enabled, multiplexors in the output path of the RA4 and RA5 pins will switch and the output of each pin will be the unsynchronized output of the comparator. The uncertainty of each of the comparators is related to the input offset voltage and the response time given in the specifications. Figure 19-3 shows the comparator output block diagram. The TRISA bits will still function as an output enable/ disable for the RA4 and RA5 pins while in this mode. EXTERNAL REFERENCE SIGNAL When external voltage references are used, the comparator module can be configured to have the comparators operate from the same or different reference sources. However, threshold detector applications may require the same reference. The reference signal must be between VSS and VDD and can be applied to either pin of the comparator(s). (c) 2009 Microchip Technology Inc. The polarity of the comparator outputs can be changed using the C2INV and C1INV bits (CMCON<4:5>). Note 1: When reading the Port register, all pins configured as analog inputs will read as a `0'. Pins configured as digital inputs will convert an analog input according to the Schmitt Trigger input specification. 2: Analog levels on any pin defined as a digital input may cause the input buffer to consume more current than is specified. DS39636D-page 225 PIC18F2X1X/4X1X + To RA4 or RA5 pin - Port pins COMPARATOR OUTPUT BLOCK DIAGRAM MULTIPLEX FIGURE 19-3: D Q Bus Data CxINV Read CMCON EN D Q EN CL From other Comparator Reset 19.6 Comparator Interrupts The comparator interrupt flag is set whenever there is a change in the output value of either comparator. Software will need to maintain information about the status of the output bits, as read from CMCON<7:6>, to determine the actual change that occurred. The CMIF bit (PIR2<6>) is the Comparator Interrupt Flag. The CMIF bit must be reset by clearing it. Since it is also possible to write a `1' to this register, a simulated interrupt may be initiated. Both the CMIE bit (PIE2<6>) and the PEIE bit (INTCON<6>) must be set to enable the interrupt. In addition, the GIE bit (INTCON<7>) must also be set. If any of these bits are clear, the interrupt is not enabled, though the CMIF bit will still be set if an interrupt condition occurs. Note: If a change in the CMCON register (C1OUT or C2OUT) should occur when a read operation is being executed (start of the Q2 cycle), then the CMIF (PIR registers) interrupt flag may not get set. The user, in the Interrupt Service Routine, can clear the interrupt in the following manner: a) b) Set CMIF bit 19.7 Comparator Operation During Sleep When a comparator is active and the device is placed in Sleep mode, the comparator remains active and the interrupt is functional if enabled. This interrupt will wake-up the device from Sleep mode, when enabled. Each operational comparator will consume additional current, as shown in the comparator specifications. To minimize power consumption while in Sleep mode, turn off the comparators (CM2:CM0 = 111) before entering Sleep. If the device wakes up from Sleep, the contents of the CMCON register are not affected. 19.8 Effects of a Reset A device Reset forces the CMCON register to its Reset state, causing the comparator modules to be turned off (CM2:CM0 = 111). However, the input pins (RA0 through RA3) are configured as analog inputs by default on device Reset. The I/O configuration for these pins is determined by the setting of the PCFG3:PCFG0 bits (ADCON1<3:0>). Therefore, device current is minimized when analog inputs are present at Reset time. Any read or write of CMCON will end the mismatch condition. Clear flag bit CMIF. A mismatch condition will continue to set flag bit CMIF. Reading CMCON will end the mismatch condition and allow flag bit CMIF to be cleared. DS39636D-page 226 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 19.9 Analog Input Connection Considerations range by more than 0.6V in either direction, one of the diodes is forward biased and a latch-up condition may occur. A maximum source impedance of 10 k is recommended for the analog sources. Any external component connected to an analog input pin, such as a capacitor or a Zener diode, should have very little leakage current. A simplified circuit for an analog input is shown in Figure 19-4. Since the analog pins are connected to a digital output, they have reverse biased diodes to VDD and VSS. The analog input, therefore, must be between VSS and VDD. If the input voltage deviates from this FIGURE 19-4: COMPARATOR ANALOG INPUT MODEL VDD VT = 0.6V RS < 10k RIC Comparator Input AIN CPIN 5 pF VA VT = 0.6V ILEAKAGE 500 nA VSS Legend: TABLE 19-1: Name CMCON CVRCON INTCON CPIN VT ILEAKAGE RIC RS VA = = = = = = Input Capacitance Threshold Voltage Leakage Current at the pin due to various junctions Interconnect Resistance Source Impedance Analog Voltage REGISTERS ASSOCIATED WITH COMPARATOR MODULE Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page C2OUT C1OUT C2INV C1INV CIS CM2 CM1 CM0 53 CVREN CVROE CVRR CVRSS CVR3 CVR2 CVR1 CVR0 53 TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 54 CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 54 54 GIE/GIEH PEIE/GIEL PIR2 OSCFIF PIE2 OCSFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE IPR2 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 54 RA7(1) RA6(1) RA5 RA4 RA3 RA2 RA1 RA0 54 LATA LATA7(1) LATA6(1) TRISA TRISA7(1) TRISA6(1) PORTA Data Direction Control Register PORTA PORTA Data Latch Register (Read and Write to Data Latch) 54 54 Legend: -- = unimplemented, read as `0'. Shaded cells are unused by the comparator module. Note 1: PORTA<7:6> and their direction and latch bits are individually configured as port pins based on various primary oscillator modes. When disabled, these bits read as `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 227 PIC18F2X1X/4X1X NOTES: DS39636D-page 228 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 20.0 COMPARATOR VOLTAGE REFERENCE MODULE The comparator voltage reference is a 16-tap resistor ladder network that provides a selectable reference voltage. Although its primary purpose is to provide a reference for the analog comparators, it may also be used independently of them. A block diagram of the module is shown in Figure 20-1. The resistor ladder is segmented to provide two ranges of CVREF values and has a power-down function to conserve power when the reference is not being used. The module's supply reference can be provided from either device VDD/VSS or an external voltage reference. 20.1 Configuring the Comparator Voltage Reference The voltage reference module is controlled through the CVRCON register (Register 20-1). The comparator voltage reference provides two ranges of output voltage, each with 16 distinct levels. The range to be REGISTER 20-1: used is selected by the CVRR bit (CVRCON<5>). The primary difference between the ranges is the size of the steps selected by the CVREF selection bits (CVR3:CVR0), with one range offering finer resolution. The equations used to calculate the output of the comparator voltage reference are as follows: If CVRR = 1: CVREF = ((CVR3:CVR0)/24) x CVRSRC If CVRR = 0: CVREF = (CVRSRC x 1/4) + (((CVR3:CVR0)/32) x CVRSRC) The comparator reference supply voltage can come from either VDD and VSS, or the external VREF+ and VREF- that are multiplexed with RA2 and RA3. The voltage source is selected by the CVRSS bit (CVRCON<4>). The settling time of the comparator voltage reference must be considered when changing the CVREF output (see Table 25-3 in Section 25.0 "Electrical Characteristics"). CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CVREN CVROE(1) CVRR CVRSS CVR3 CVR2 CVR1 CVR0 bit 7 bit 0 bit 7 CVREN: Comparator Voltage Reference Enable bit 1 = CVREF circuit powered on 0 = CVREF circuit powered down bit 6 CVROE: Comparator VREF Output Enable bit(1) 1 = CVREF voltage level is also output on the RA2/AN2/VREF-/CVREF pin 0 = CVREF voltage is disconnected from the RA2/AN2/VREF-/CVREF pin Note 1: CVROE overrides the TRISA<2> bit setting. bit 5 CVRR: Comparator VREF Range Selection bit 1 = 0 to 0.667 CVRSRC, with CVRSRC/24 step size (low range) 0 = 0.25 CVRSRC to 0.75 CVRSRC, with CVRSRC/32 step size (high range) bit 4 CVRSS: Comparator VREF Source Selection bit 1 = Comparator reference source, CVRSRC = (VREF+) - (VREF-) 0 = Comparator reference source, CVRSRC = VDD - VSS bit 3-0 CVR3:CVR0: Comparator VREF Value Selection bits (0 (CVR3:CVR0) 15) When CVRR = 1: CVREF = ((CVR3:CVR0)/24) * (CVRSRC) When CVRR = 0: CVREF = (CVRSRC/4) + ((CVR3:CVR0)/32) * (CVRSRC) Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 229 PIC18F2X1X/4X1X FIGURE 20-1: COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM VREF+ VDD CVRSS = 1 8R CVRSS = 0 CVR3:CVR0 R CVREN R R 16-to-1 MUX R 16 Steps R CVREF R R CVRR VREF- 8R CVRSS = 1 CVRSS = 0 20.2 Voltage Reference Accuracy/Error The full range of voltage reference cannot be realized due to the construction of the module. The transistors on the top and bottom of the resistor ladder network (Figure 20-1) keep CVREF from approaching the reference source rails. The voltage reference is derived from the reference source; therefore, the CVREF output changes with fluctuations in that source. The tested absolute accuracy of the voltage reference can be found in Section 25.0 "Electrical Characteristics". 20.3 Operation During Sleep When the device wakes up from Sleep through an interrupt or a Watchdog Timer time-out, the contents of the CVRCON register are not affected. To minimize current consumption in Sleep mode, the voltage reference should be disabled. 20.4 Effects of a Reset A device Reset disables the voltage reference by clearing bit CVREN (CVRCON<7>). This Reset also disconnects the reference from the RA2 pin by clearing bit CVROE (CVRCON<6>) and selects the high-voltage range by clearing bit CVRR (CVRCON<5>). The CVR value select bits are also cleared. 20.5 Connection Considerations The voltage reference module operates independently of the comparator module. The output of the reference generator may be connected to the RA2 pin if the CVROE bit is set. Enabling the voltage reference output onto RA2 when it is configured as a digital input will increase current consumption. Connecting RA2 as a digital output with CVRSS enabled will also increase current consumption. The RA2 pin can be used as a simple D/A output with limited drive capability. Due to the limited current drive capability, a buffer must be used on the voltage reference output for external connections to VREF. Figure 20-2 shows an example buffering technique. DS39636D-page 230 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 20-2: COMPARATOR VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE PIC18FXXXX CVREF Module R(1) Voltage Reference Output Impedance Note 1: TABLE 20-1: Name CVREF Output R is dependent upon the voltage reference configuration bits, CVRCON<3:0> and CVRCON<5>. REGISTERS ASSOCIATED WITH COMPARATOR VOLTAGE REFERENCE Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on page CVROE CVRR CVRSS CVR3 CVR2 CVR1 CVR0 53 C1OUT C2INV C1INV CIS CM2 CM1 CM0 53 Bit 7 Bit 6 CVRCON CVREN CMCON C2OUT TRISA + - RA2 TRISA7 (1) TRISA6(1) PORTA Data Direction Control Register 54 Legend: Shaded cells are not used with the comparator voltage reference. Note 1: PORTA pins are enabled based on oscillator configuration. (c) 2009 Microchip Technology Inc. DS39636D-page 231 PIC18F2X1X/4X1X NOTES: DS39636D-page 232 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 21.0 HIGH/LOW-VOLTAGE DETECT (HLVD) PIC18F2X1X/4X1X devices have a High/Low-Voltage Detect module (HLVD). This is a programmable circuit that allows the user to specify both a device voltage trip point and the direction of change from that point. If the device experiences an excursion past the trip point in that direction, an interrupt flag is set. If the interrupt is enabled, the program execution will branch to the interrupt vector address and the software can then respond to the interrupt. REGISTER 21-1: The High/Low-Voltage Detect Control register (Register 21-1) completely controls the operation of the HLVD module. This allows the circuitry to be "turned off" by the user under software control, which minimizes the current consumption for the device. The block diagram for the HLVD module is shown in Figure 21-1. HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER R/W-0 U-0 R-0 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1 VDIRMAG -- IRVST HLVDEN HLVDL3 HLVDL2 HLVDL1 HLVDL0 bit 7 bit 0 bit 7 VDIRMAG: Voltage Direction Magnitude Select bit 1 = Event occurs when voltage equals or exceeds trip point (HLVDL3:HLDVL0) 0 = Event occurs when voltage equals or falls below trip point (HLVDL3:HLVDL0) bit 6 Unimplemented: Read as `0' bit 5 IRVST: Internal Reference Voltage Stable Flag bit 1 = Indicates that the voltage detect logic will generate the interrupt flag at the specified voltage range 0 = Indicates that the voltage detect logic will not generate the interrupt flag at the specified voltage range and the HLVD interrupt should not be enabled bit 4 HLVDEN: High/Low-Voltage Detect Power Enable bit 1 = HLVD enabled 0 = HLVD disabled bit 3-0 HLVDL3:HLVDL0: Voltage Detection Limit bits 1111 = External analog input is used (input comes from the HLVDIN pin) 1110 = Maximum setting . . . 0000 = Minimum setting Note: See Table 25-4 in Section 25.0 "Electrical Characteristics" for the specifications. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared (c) 2009 Microchip Technology Inc. x = Bit is unknown DS39636D-page 233 PIC18F2X1X/4X1X The module is enabled by setting the HLVDEN bit. Each time that the HLVD module is enabled, the circuitry requires some time to stabilize. The IRVST bit is a read-only bit and is used to indicate when the circuit is stable. The module can only generate an interrupt after the circuit is stable and IRVST is set. event, depending on the configuration of the module. When the supply voltage is equal to the trip point, the voltage tapped off of the resistor array is equal to the internal reference voltage generated by the voltage reference module. The comparator then generates an interrupt signal by setting the HLVDIF bit. The VDIRMAG bit determines the overall operation of the module. When VDIRMAG is cleared, the module monitors for drops in VDD below a predetermined set point. When the bit is set, the module monitors for rises in VDD above the set point. The trip point voltage is software programmable to any one of 16 values. The trip point is selected by programming the HLVDL3:HLVDL0 bits (HLVDCON<3:0>). 21.1 Operation When the HLVD module is enabled, a comparator uses an internally generated reference voltage as the set point. The set point is compared with the trip point, where each node in the resistor divider represents a trip point voltage. The "trip point" voltage is the voltage level at which the device detects a high or low-voltage FIGURE 21-1: VDD HLVD MODULE BLOCK DIAGRAM (WITH EXTERNAL INPUT) Externally Generated Trip Point VDD HLVDL3:HLVDL0 HLVDCON Register HLVDEN HLVDIN VDIRMAG Set HLVDIF 16 to 1 MUX HLVDIN The HLVD module has an additional feature that allows the user to supply the trip voltage to the module from an external source. This mode is enabled when bits HLVDL3:HLVDL0 are set to `1111'. In this state, the comparator input is multiplexed from the external input pin, HLVDIN. This gives users flexibility because it allows them to configure the High/Low-Voltage Detect interrupt to occur at any voltage in the valid operating range. HLVDEN BOREN DS39636D-page 234 Internal Voltage Reference (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 21.2 HLVD Setup Depending on the application, the HLVD module does not need to be operating constantly. To decrease the current requirements, the HLVD circuitry may only need to be enabled for short periods where the voltage is checked. After doing the check, the HLVD module may be disabled. The following steps are needed to set up the HLVD module: 1. 2. 3. 4. 5. 6. Disable the module by clearing the HLVDEN bit (HLVDCON<4>). Write the value to the HLVDL3:HLVDL0 bits that selects the desired HLVD trip point. Set the VDIRMAG bit to detect high voltage (VDIRMAG = 1) or low voltage (VDIRMAG = 0). Enable the HLVD module by setting the HLVDEN bit. Clear the HLVD interrupt flag (PIR2<2>), which may have been set from a previous interrupt. Enable the HLVD interrupt if interrupts are desired by setting the HLVDIE and GIE bits (PIE<2> and INTCON<7>). An interrupt will not be generated until the IRVST bit is set. 21.3 21.4 The internal reference voltage of the HLVD module, specified in electrical specification parameter D420, may be used by other internal circuitry, such as the Programmable Brown-out Reset. If the HLVD or other circuits using the voltage reference are disabled to lower the device's current consumption, the reference voltage circuit will require time to become stable before a low or high-voltage condition can be reliably detected. This start-up time, TIRVST, is an interval that is independent of device clock speed. It is specified in electrical specification parameter 36. Current Consumption The HLVD interrupt flag is not enabled until TIRVST has expired and a stable reference voltage is reached. For this reason, brief excursions beyond the set point may not be detected during this interval. Refer to Figure 21-2 or Figure 21-3. When the module is enabled, the HLVD comparator and voltage divider are enabled and will consume static current. The total current consumption, when enabled, is specified in electrical specification parameter D022B. FIGURE 21-2: HLVD Start-up Time LOW-VOLTAGE DETECT OPERATION (VDIRMAG = 0) CASE 1: HLVDIF may not be set VDD VLVD HLVDIF Enable HLVD TIVRST IRVST Internal Reference is stable HLVDIF cleared in software CASE 2: VDD VLVD HLVDIF Enable HLVD TIVRST IRVST Internal Reference is stable HLVDIF cleared in software HLVDIF cleared in software, HLVDIF remains set since HLVD condition still exists (c) 2009 Microchip Technology Inc. DS39636D-page 235 PIC18F2X1X/4X1X FIGURE 21-3: HIGH-VOLTAGE DETECT OPERATION (VDIRMAG = 1) CASE 1: HLVDIF may not be set VLVD VDD HLVDIF Enable HLVD TIVRST IRVST HLVDIF cleared in software Internal Reference is stable CASE 2: VLVD VDD HLVDIF Enable HLVD TIVRST IRVST Internal Reference is stable HLVDIF cleared in software HLVDIF cleared in software, HLVDIF remains set since HLVD condition still exists Applications In many applications, the ability to detect a drop below or rise above a particular threshold is desirable. For example, the HLVD module could be periodically enabled to detect a Universal Serial Bus (USB) attach or detach. This assumes the device is powered by a lower voltage source than the USB when detached. An attach would indicate a high-voltage detect from, for example, 3.3V to 5V (the voltage on USB) and vice versa for a detach. This feature could save a design a few extra components and an attach signal (input pin). For general battery applications, Figure 21-4 shows a possible voltage curve. Over time, the device voltage decreases. When the device voltage reaches voltage VA, the HLVD logic generates an interrupt at time TA. The interrupt could cause the execution of an ISR, which would allow the application to perform "housekeeping tasks" and perform a controlled shutdown before the device voltage exits the valid operating range at TB. The HLVD thus would give the application a time window, represented by the difference between TA and TB, to safely exit. DS39636D-page 236 FIGURE 21-4: TYPICAL HIGH/LOW-VOLTAGE DETECT APPLICATION VA VB Voltage 21.5 Time TA TB Legend: VA = HLVD trip point VB = Minimum valid device operating voltage (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 21.6 Operation During Sleep 21.7 When enabled, the HLVD circuitry continues to operate during Sleep. If the device voltage crosses the trip point, the HLVDIF bit will be set and the device will wake-up from Sleep. Device execution will continue from the interrupt vector address if interrupts have been globally enabled. TABLE 21-1: Effects of a Reset A device Reset forces all registers to their Reset state. This forces the HLVD module to be turned off. REGISTERS ASSOCIATED WITH HIGH/LOW-VOLTAGE DETECT MODULE Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset Values on Page HLVDCON VDIRMAG -- IRVST HLVDEN HLVDL3 HLVDL2 HLVDL1 HLVDL0 52 INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 51 PIR2 OSCFIF CMIF -- -- BCLIF HLVDIF TMR3IF CCP2IF 54 PIE2 OCSFIE CMIE -- -- BCLIE HLVDIE TMR3IE CCP2IE 54 IPR2 OSCFIP CMIP -- -- BCLIP HLVDIP TMR3IP CCP2IP 54 Legend: -- = unimplemented, read as `0'. Shaded cells are unused by the HLVD module. (c) 2009 Microchip Technology Inc. DS39636D-page 237 PIC18F2X1X/4X1X NOTES: DS39636D-page 238 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 22.0 SPECIAL FEATURES OF THE CPU A complete discussion of device Resets and interrupts is available in previous sections of this data sheet. PIC18F2X1X/4X1X devices include several features intended to maximize reliability and minimize cost through elimination of external components. These are: * Oscillator Selection * Resets: - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) * Interrupts * Watchdog Timer (WDT) * Fail-Safe Clock Monitor * Two-Speed Start-up * Code Protection * ID Locations * In-Circuit Serial Programming The inclusion of an internal RC oscillator also provides the additional benefits of a Fail-Safe Clock Monitor (FSCM) and Two-Speed Start-up. FSCM provides for background monitoring of the peripheral clock and automatic switchover in the event of its failure. TwoSpeed Start-up enables code to be executed almost immediately on start-up, while the primary clock source completes its start-up delays. All of these features are enabled and configured by setting the appropriate Configuration register bits. 22.1 The oscillator can be configured for the application depending on frequency, power, accuracy and cost. All of the options are discussed in detail in Section 2.0 "Oscillator Configurations". TABLE 22-1: Configuration Bits The Configuration bits can be programmed (read as `0') or left unprogrammed (read as `1') to select various device configurations. These bits are mapped starting at program memory location 300000h. The user will note that address 300000h is beyond the user program memory space. In fact, it belongs to the configuration memory space (300000h-3FFFFFh), which can only be accessed using table reads. CONFIGURATION BITS AND DEVICE IDs File Name 300001h In addition to their Power-up and Oscillator Start-up Timers provided for Resets, PIC18F2X1X/4X1X devices have a Watchdog Timer, which is either permanently enabled via the Configuration bits or software controlled (if configured as disabled). Default/ Unprogrammed Value Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CONFIG1H IESO FCMEN -- -- FOSC3 FOSC2 FOSC1 FOSC0 00-- 0111 ---1 1111 300002h CONFIG2L -- -- -- BORV1 BORV0 BOREN1 BOREN0 PWRTEN 300003h CONFIG2H -- -- -- WDTPS3 WDTPS2 WDTPS1 WDTPS0 WDTEN ---1 1111 300005h CONFIG3H MCLRE -- -- -- -- LPT1OSC PBADEN CCP2MX 1--- -011 10-- -1-1 300006h CONFIG4L DEBUG XINST -- -- -- LVP -- STVREN 300008h CONFIG5L -- -- -- -- CP3(1,2) CP2(1) CP1 CP0 ---- 1111 300009h CONFIG5H -- CPB -- -- -- -- -- -- -1-- ---- 30000Ah CONFIG6L -- -- -- -- WRT3(1,2) WRT2(1) WRT1 WRT0 ---- 1111 30000Bh CONFIG6H -- WRTB WRTC -- -- -- -- -- -11- ---- 30000Ch CONFIG7L -- -- -- -- EBTR3(1,2) EBTR2(1) EBTR1 EBTR0 ---- 1111 30000Dh CONFIG7H -- EBTRB -- -- -- -- -- -- -1-- ---- 3FFFFEh DEVID1(3) DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 xxxx xxxx(3) 3FFFFFh DEVID2(3) DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 0000 1100 Legend: x = unknown, u = unchanged, -- = unimplemented, q = value depends on condition. Shaded cells are unimplemented, read as `0'. Unimplemented in PIC18F2410/4410 devices; maintain this bit set. Unimplemented in PIC18F2515/4515 devices, maintain this bit set. See Register 22-14 for DEVID1 values. DEVID registers are read-only and cannot be programmed by the user. Note 1: 2: 3: (c) 2009 Microchip Technology Inc. DS39636D-page 239 PIC18F2X1X/4X1X REGISTER 22-1: CONFIG1H: CONFIGURATION REGISTER 1 HIGH (BYTE ADDRESS 300001h) R/P-0 R/P-0 U-0 U-0 R/P-0 R/P-1 R/P-1 R/P-1 IESO FCMEN -- -- FOSC3 FOSC2 FOSC1 FOSC0 bit 7 bit 0 bit 7 IESO: Internal/External Oscillator Switchover bit 1 = Oscillator Switchover mode enabled 0 = Oscillator Switchover mode disabled bit 6 FCMEN: Fail-Safe Clock Monitor Enable bit 1 = Fail-Safe Clock Monitor enabled 0 = Fail-Safe Clock Monitor disabled bit 5-4 Unimplemented: Read as `0' bit 3-0 FOSC3:FOSC0: Oscillator Selection bits 11xx = External RC oscillator, CLKO function on RA6 101x = External RC oscillator, CLKO function on RA6 1001 = Internal oscillator block, CLKO function on RA6, port function on RA7 1000 = Internal oscillator block, port function on RA6 and RA7 0111 = External RC oscillator, port function on RA6 0110 = HS oscillator, PLL enabled (Clock Frequency = 4 x FOSC1) 0101 = EC oscillator, port function on RA6 0100 = EC oscillator, CLKO function on RA6 0011 = External RC oscillator, CLKO function on RA6 0010 = HS oscillator 0001 = XT oscillator 0000 = LP oscillator Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed DS39636D-page 240 U = Unimplemented bit, read as `0' u = Unchanged from programmed state (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 22-2: CONFIG2L: CONFIGURATION REGISTER 2 LOW (BYTE ADDRESS 300002h) U-0 U-0 -- -- U-0 -- R/P-1 BORV1 (1) R/P-1 BORV0 (1) R/P-1 R/P-1 (2) BOREN1 R/P-1 (2) BOREN0 PWRTEN(2) bit 7 bit 0 bit 7-5 Unimplemented: Read as `0' bit 4-3 BORV1:BORV0: Brown-out Reset Voltage bits(1) 11 = Minimum setting . . . 00 = Maximum setting bit 2-1 BOREN1:BOREN0: Brown-out Reset Enable bits(2) 11 = Brown-out Reset enabled in hardware only (SBOREN is disabled) 10 = Brown-out Reset enabled in hardware only and disabled in Sleep mode (SBOREN is disabled) 01 = Brown-out Reset enabled and controlled by software (SBOREN is enabled) 00 = Brown-out Reset disabled in hardware and software bit 0 PWRTEN: Power-up Timer Enable bit(2) 1 = PWRT disabled 0 = PWRT enabled Note 1: See Section 25.1 "DC Characteristics" for the specifications. 2: The Power-up Timer is decoupled from Brown-out Reset, allowing these features to be independently controlled. Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed (c) 2009 Microchip Technology Inc. U = Unimplemented bit, read as `0' u = Unchanged from programmed state DS39636D-page 241 PIC18F2X1X/4X1X REGISTER 22-3: CONFIG2H: CONFIGURATION REGISTER 2 HIGH (BYTE ADDRESS 300003h) U-0 U-0 U-0 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 -- -- -- WDTPS3 WDTPS2 WDTPS1 WDTPS0 WDTEN bit 7 bit 0 bit 7-5 Unimplemented: Read as `0' bit 4-1 WDTPS3:WDTPS0: Watchdog Timer Postscale Select bits 1111 = 1:32,768 1110 = 1:16,384 1101 = 1:8,192 1100 = 1:4,096 1011 = 1:2,048 1010 = 1:1,024 1001 = 1:512 1000 = 1:256 0111 = 1:128 0110 = 1:64 0101 = 1:32 0100 = 1:16 0011 = 1:8 0010 = 1:4 0001 = 1:2 0000 = 1:1 bit 0 WDTEN: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled (control is placed on the SWDTEN bit) Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed DS39636D-page 242 U = Unimplemented bit, read as `0' u = Unchanged from programmed state (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 22-4: CONFIG3H: CONFIGURATION REGISTER 3 HIGH (BYTE ADDRESS 300005h) R/P-1 U-0 U-0 U-0 U-0 R/P-0 R/P-1 R/P-1 MCLRE -- -- -- -- LPT1OSC PBADEN CCP2MX bit 7 bit 0 bit 7 MCLRE: MCLR Pin Enable bit 1 = MCLR pin enabled; RE3 input pin disabled 0 = RE3 input pin enabled; MCLR disabled bit 6-3 Unimplemented: Read as `0' bit 2 LPT1OSC: Low-Power Timer1 Oscillator Enable bit 1 = Timer1 configured for low-power operation 0 = Timer1 configured for higher power operation bit 1 PBADEN: PORTB A/D Enable bit (Affects ADCON1 Reset state. ADCON1 controls PORTB<4:0> pin configuration.) 1 = PORTB<4:0> pins are configured as analog input channels on Reset 0 = PORTB<4:0> pins are configured as digital I/O on Reset bit 0 CCP2MX: CCP2 Mux bit 1 = CCP2 input/output is multiplexed with RC1 0 = CCP2 input/output is multiplexed with RB3 Legend: R = Readable bit P = Programmable bit -n = Value when device is unprogrammed REGISTER 22-5: U = Unimplemented bit, read as `0' u = Unchanged from programmed state CONFIG4L: CONFIGURATION REGISTER 4 LOW (BYTE ADDRESS 300006h) R/P-1 R/P-0 U-0 U-0 U-0 R/P-1 U-0 R/P-1 DEBUG XINST -- -- -- LVP -- STVREN bit 7 bit 0 bit 7 DEBUG: Background Debugger Enable bit 1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins 0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug bit 6 XINST: Extended Instruction Set Enable bit 1 = Instruction set extension and Indexed Addressing mode enabled 0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode) bit 5-3 Unimplemented: Read as `0' bit 2 LVP: Single-Supply ICSP Enable bit 1 = Single-Supply ICSP enabled 0 = Single-Supply ICSP disabled bit 1 Unimplemented: Read as `0' bit 0 STVREN: Stack Full/Underflow Reset Enable bit 1 = Stack full/underflow will cause Reset 0 = Stack full/underflow will not cause Reset Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed (c) 2009 Microchip Technology Inc. U = Unimplemented bit, read as `0' u = Unchanged from programmed state DS39636D-page 243 PIC18F2X1X/4X1X REGISTER 22-6: CONFIG5L: CONFIGURATION REGISTER 5 LOW (BYTE ADDRESS 300008h) U-0 U-0 U-0 U-0 R/C-1 R/C-1 R/C-1 R/C-1 -- -- -- -- CP3(1,2) CP2(1) CP1 CP0 bit 7 bit 0 bit 7-4 Unimplemented: Read as `0' bit 3 CP3: Code Protection bit(1,2) 1 = Block 3 (006000-007FFFh) not code-protected(3) 0 = Block 3 (006000-007FFFh) code-protected(3) 1 = Block 3 (00C000-00FFFFh) not code-protected(4) 0 = Block 3 (00C000-00FFFFh) code-protected(4) bit 2 CP2: Code Protection bit(1) 1 = Block 2 (004000-005FFFh) not code-protected(3) 0 = Block 2 (004000-005FFFh) code-protected(3) 1 = Block 2 (008000-00BFFFh) not code-protected(4) 0 = Block 2 (008000-00BFFFh) code-protected(4) bit 1 CP1: Code Protection bit 1 = Block 1 (002000-003FFFh) not code-protected(3) 0 = Block 1 (002000-003FFFh) code-protected(3) 1 = Block 1 (004000-007FFFh) not code-protected(4) 0 = Block 1 (004000-007FFFh) code-protected(4) bit 0 CP0: Code Protection bit 1 = Block 0 (000800-001FFFh) not code-protected(3) 0 = Block 0 (000800-001FFFh) code-protected(3) 1 = Block 0 (000800-003FFFh) not code-protected(4) 0 = Block 0 (000800-003FFFh) code-protected(4) Note 1: 2: 3: 4: Unimplemented in PIC18F2410/4410 devices; maintain this bit set. Unimplemented in PIC18F2515/4515 devices; maintain this bit set. Address range for 16K and 32K devices. Address range for 48K and 64K devices. Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed REGISTER 22-7: U = Unimplemented bit, read as `0' u = Unchanged from programmed state CONFIG5H: CONFIGURATION REGISTER 5 HIGH (BYTE ADDRESS 300009h) U-0 R/C-1 U-0 U-0 U-0 U-0 U-0 U-0 -- CPB -- -- -- -- -- -- bit 7 bit 0 bit 7 Unimplemented: Read as `0' bit 6 CPB: Boot Block Code Protection bit 1 = Boot block (000000-0007FFh) not code-protected 0 = Boot block (000000-0007FFh) code-protected bit 5-0 Unimplemented: Read as `0' Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed DS39636D-page 244 U = Unimplemented bit, read as `0' u = Unchanged from programmed state (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 22-8: CONFIG6L: CONFIGURATION REGISTER 6 LOW (BYTE ADDRESS 30000Ah) U-0 -- U-0 -- U-0 -- U-0 -- R/C-1 WRT3 (1,2) R/C-1 WRT2 (1) R/C-1 R/C-1 WRT1 WRT0 bit 7 bit 0 bit 7-4 Unimplemented: Read as `0' bit 3 WRT3: Write Protection bit(1,2) 1 = Block 3 (006000-007FFFh) not write-protected(3) 0 = Block 3 (006000-007FFFh) write-protected(3) 1 = Block 3 (00C000-00FFFFh) not write-protected(4) 0 = Block 3 (00C000-00FFFFh) write-protected(4) bit 2 WRT2: Write Protection bit(1) 1 = Block 2 (004000-005FFFh) not write-protected(3) 0 = Block 2 (004000-005FFFh) write-protected(3) 1 = Block 2 (008000-00BFFFh) not write-protected(4) 0 = Block 2 (008000-00BFFFh) write-protected(4) bit 1 WRT1: Write Protection bit 1 = Block 1 (002000-003FFFh) not write-protected(3) 0 = Block 1 (002000-003FFFh) write-protected(3) 1 = Block 1 (004000-007FFFh) not write-protected(4) 0 = Block 1 (004000-007FFFh) write-protected(4) bit 0 WRT0: Write Protection bit 1 = Block 0 (000800-001FFFh) not write-protected(3) 0 = Block 0 (000800-001FFFh) write-protected(3) 1 = Block 0 (000800-003FFFh) not write-protected(4) 0 = Block 0 (000800-003FFFh) write-protected(4) Note 1: 2: 3: 4: Unimplemented in PIC18F2410/4410 devices; maintain this bit set. Unimplemented in PIC18F2515/4515 devices; maintain this bit set. Address range for 16K and 32K devices. Address range for 48K and 64K devices. Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed REGISTER 22-9: U = Unimplemented bit, read as `0' u = Unchanged from programmed state CONFIG6H: CONFIGURATION REGISTER 6 HIGH (BYTE ADDRESS 30000Bh) U-0 -- R/C-1 R-1 U-0 U-0 U-0 U-0 U-0 WRTB WRTC(1) -- -- -- -- -- bit 7 bit 0 bit 7 Unimplemented: Read as `0' bit 6 WRTB: Boot Block Write Protection bit 1 = Boot block (000000-0007FFh) not write-protected 0 = Boot block (000000-0007FFh) write-protected bit 5 WRTC: Configuration Register Write Protection bit(1) 1 = Configuration registers (300000-3000FFh) not write-protected 0 = Configuration registers (300000-3000FFh) write-protected Note 1: This bit is read-only in Normal Execution mode; it can be written only in Program mode. bit 4-0 Unimplemented: Read as `0' Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed (c) 2009 Microchip Technology Inc. U = Unimplemented bit, read as `0' u = Unchanged from programmed state DS39636D-page 245 PIC18F2X1X/4X1X REGISTER 22-10: CONFIG7L: CONFIGURATION REGISTER 7 LOW (BYTE ADDRESS 30000Ch) U-0 U-0 U-0 U-0 R/C-1 R/C-1 R/C-1 R/C-1 -- -- -- -- EBTR3(1,2) EBTR2(1) EBTR1 EBTR0 bit 7 bit 0 bit 7-4 Unimplemented: Read as `0' bit 3 EBTR3: Table Read Protection bit(1,2) 1 = Block 3 (006000-007FFFh) not protected from table reads executed in other blocks(3) 0 = Block 3 (006000-007FFFh) protected from table reads executed in other blocks(3) 1 = Block 3 (00C000-00FFFFh) not protected from table reads executed in other blocks(4) 0 = Block 3 (00C000-00FFFFh) protected from table reads executed in other blocks(4) bit 2 EBTR2: Table Read Protection bit(1) 1 = Block 2 (004000-005FFFh) not protected from table reads executed in other blocks(3) 0 = Block 2 (004000-005FFFh) protected from table reads executed in other blocks(3) 1 = Block 2 (008000-00BFFFh) not protected from table reads executed in other blocks(4) 0 = Block 2 (008000-00BFFFh) protected from table reads executed in other blocks(4) bit 1 EBTR1: Table Read Protection bit 1 = Block 1 (002000-003FFFh) not protected from table reads executed in other blocks(3) 0 = Block 1 (002000-003FFFh) protected from table reads executed in other blocks(3) 1 = Block 1 (004000-007FFFh) not protected from table reads executed in other blocks(4) 0 = Block 1 (004000-007FFFh) protected from table reads executed in other blocks(4) bit 0 EBTR0: Table Read Protection bit 1 = Block 0 (000800-001FFFh) not protected from table reads executed in other blocks(3) 0 = Block 0 (000800-001FFFh) protected from table reads executed in other blocks(3) 1 = Block 0 (000800-003FFFh) not protected from table reads executed in other blocks(4) 0 = Block 0 (000800-003FFFh) protected from table reads executed in other blocks(4) Note 1: 2: 3: 4: Unimplemented in PIC18F2410/4410 devices; maintain this bit set. Unimplemented in PIC18F2515/4515 devices; maintain this bit set. Address range for 16K and 32K devices. Address range for 48K and 64K devices. Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as `0' u = Unchanged from programmed state REGISTER 22-11: CONFIG7H: CONFIGURATION REGISTER 7 HIGH (BYTE ADDRESS 30000Dh) U-0 R/C-1 U-0 U-0 U-0 U-0 U-0 U-0 -- EBTRB -- -- -- -- -- -- bit 7 bit 0 bit 7 Unimplemented: Read as `0' bit 6 EBTRB: Boot Block Table Read Protection bit 1 = Boot block (000000-0007FFh) not protected from table reads executed in other blocks 0 = Boot block (000000-0007FFh) protected from table reads executed in other blocks bit 5-0 Unimplemented: Read as `0' Legend: R = Readable bit C = Clearable bit -n = Value when device is unprogrammed DS39636D-page 246 U = Unimplemented bit, read as `0' u = Unchanged from programmed state (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 22-12: DEVICE ID REGISTER 1 FOR PIC18F2X1X/4X1X DEVICES R R R R R R R R DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 bit 7 bit 0 bit 7-5 DEV2:DEV0: Device ID bits 011 = PIC18F2410 001 = PIC18F2510 111 = PIC18F2515 101 = PIC18F2610 111 = PIC18F4410 101 = PIC18F4510 011 = PIC18F4515 001 = PIC18F4610 bit 4-0 REV4:REV0: Revision ID bits These bits are used to indicate the device revision. Legend: R = Read-only bit P = Programmable bit -n = Value when device is unprogrammed U = Unimplemented bit, read as `0' u = Unchanged from programmed state REGISTER 22-13: DEVICE ID REGISTER 2 FOR PIC18F2X1X/4X1X DEVICES R R R R R R R R DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 bit 7 bit 7-0 bit 0 DEV10:DEV3: Device ID bits These bits are used with the DEV2:DEV0 bits in the Device ID Register 1 to identify the part number. 0000 1100 = PIC18F4610/2610/4515/2515 devices 0001 0001 = PIC18F2510/2410 devices 0000 1100 = PIC18F4510/4410 devices Note: These values for DEV10:DEV3 may be shared with other devices. The specific device is always identified by using the entire DEV10:DEV0 bit sequence. Legend: R = Read-only bit P = Programmable bit -n = Value when device is unprogrammed (c) 2009 Microchip Technology Inc. U = Unimplemented bit, read as `0' u = Unchanged from programmed state DS39636D-page 247 PIC18F2X1X/4X1X 22.2 Watchdog Timer (WDT) For PIC18F2X1X/4X1X devices, the WDT is driven by the INTRC source. When the WDT is enabled, the clock source is also enabled. The nominal WDT period is 4 ms and has the same stability as the INTRC oscillator. The 4 ms period of the WDT is multiplied by a 16-bit postscaler. Any output of the WDT postscaler is selected by a multiplexer, controlled by bits in Configuration Register 2H. Available periods range from 4 ms to 131.072 seconds (2.18 minutes). The WDT and postscaler are cleared when any of the following events occur: a SLEEP or CLRWDT instruction is executed, the IRCF bits (OSCCON<6:4>) are changed or a clock failure has occurred. FIGURE 22-1: Note 1: The CLRWDT and SLEEP instructions clear the WDT and postscaler counts when executed. 2: Changing the setting of the IRCF bits (OSCCON<6:4>) clears the WDT and postscaler counts. 3: When a CLRWDT instruction is executed, the postscaler count will be cleared. 22.2.1 CONTROL REGISTER Register 22-14 shows the WDTCON register. This is a readable and writable register which contains a control bit that allows software to override the WDT Configuration bit, but only if the Configuration bit has disabled the WDT. WDT BLOCK DIAGRAM SWDTEN WDTEN Enable WDT WDT Counter INTRC Source Wake-up From Power-Managed Modes /128 Change on IRCF bits Programmable Postscaler 1:1 to 1:32,768 CLRWDT Reset WDT Reset All Device Resets WDTPS<3:0> 4 Sleep DS39636D-page 248 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X REGISTER 22-14: WDTCON: WATCHDOG TIMER CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 -- -- -- -- -- -- -- SWDTEN(1) bit 7 bit 0 bit 7-1 Unimplemented: Read as `0' bit 0 SWDTEN: Software Controlled Watchdog Timer Enable bit(1) 1 = Watchdog Timer is on 0 = Watchdog Timer is off Note 1: This bit has no effect if the Configuration bit, WDTEN, is enabled. Legend: TABLE 22-2: Name RCON WDTCON R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR SUMMARY OF WATCHDOG TIMER REGISTERS Bit 0 Reset Values on page POR BOR 50 -- SWDTEN(2) 52 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 IPEN SBOREN(1) -- RI TO PD -- -- -- -- -- -- Legend: -- = unimplemented, read as `0'. Shaded cells are not used by the Watchdog Timer. Note 1: The SBOREN bit is only available when the BOREN1:BOREN0 Configuration bits = 01; otherwise, it is disabled and reads as `0'. See Section 4.4 "Brown-out Reset (BOR)". 2: This bit has no effect if the Configuration bit, WDTEN, is enabled. (c) 2009 Microchip Technology Inc. DS39636D-page 249 PIC18F2X1X/4X1X 22.3 Two-Speed Start-up In all other power-managed modes, Two-Speed Startup is not used. The device will be clocked by the currently selected clock source until the primary clock source becomes available. The setting of the IESO bit is ignored. The Two-Speed Start-up feature helps to minimize the latency period from oscillator start-up to code execution by allowing the microcontroller to use the INTOSC oscillator as a clock source until the primary clock source is available. It is enabled by setting the IESO Configuration bit. 22.3.1 Two-Speed Start-up should be enabled only if the Primary Oscillator mode is LP, XT, HS or HSPLL (Crystal-Based modes). Other sources do not require an OST start-up delay; for these, Two-Speed Start-up should be disabled. While using the INTOSC oscillator in Two-Speed Startup, the device still obeys the normal command sequences for entering power-managed modes, including multiple SLEEP instructions (refer to Section 3.1.4 "Multiple Sleep Commands"). In practice, this means that user code can change the SCS1:SCS0 bit settings or issue SLEEP instructions before the OST times out. This would allow an application to briefly wake-up, perform routine "housekeeping" tasks and return to Sleep before the device starts to operate from the primary oscillator. When enabled, Resets and wake-ups from Sleep mode cause the device to configure itself to run from the internal oscillator block as the clock source, following the time-out of the Power-up Timer after a Power-on Reset is enabled. This allows almost immediate code execution while the primary oscillator starts and the OST is running. Once the OST times out, the device automatically switches to PRI_RUN mode. User code can also check if the primary clock source is currently providing the device clocking by checking the status of the OSTS bit (OSCCON<3>). If the bit is set, the primary oscillator is providing the clock. Otherwise, the internal oscillator block is providing the clock during wake-up from Reset or Sleep mode. To use a higher clock speed on wake-up, the INTOSC or postscaler clock sources can be selected to provide a higher clock speed by setting bits IRCF2:IRCF0 immediately after Reset. For wake-ups from Sleep, the INTOSC or postscaler clock sources can be selected by setting the IRCF2:IRCF0 bits prior to entering Sleep mode. FIGURE 22-2: SPECIAL CONSIDERATIONS FOR USING TWO-SPEED START-UP TIMING TRANSITION FOR TWO-SPEED START-UP (INTOSC TO HSPLL) Q1 Q3 Q2 Q4 Q2 Q3 Q4 Q1 Q2 Q3 Q1 INTOSC Multiplexer OSC1 TOST(1) TPLL(1) 1 PLL Clock Output 2 n-1 n Clock Transition(2) CPU Clock Peripheral Clock Program Counter PC Wake from Interrupt Event Note 1: 2: DS39636D-page 250 PC + 2 PC + 6 PC + 4 OSTS bit Set TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale. Clock transition typically occurs within 2-4 TOSC. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 22.4 Fail-Safe Clock Monitor The Fail-Safe Clock Monitor (FSCM) allows the microcontroller to continue operation in the event of an external oscillator failure by automatically switching the device clock to the internal oscillator block. The FSCM function is enabled by setting the FCMEN Configuration bit. When FSCM is enabled, the INTRC oscillator runs at all times to monitor clocks to peripherals and provide a backup clock in the event of a clock failure. Clock monitoring (shown in Figure 22-3) is accomplished by creating a sample clock signal, which is the INTRC output divided by 64. This allows ample time between FSCM sample clocks for a peripheral clock edge to occur. The peripheral device clock and the sample clock are presented as inputs to the Clock Monitor latch (CM). The CM is set on the falling edge of the device clock source, but cleared on the rising edge of the sample clock. FIGURE 22-3: FSCM BLOCK DIAGRAM Clock Monitor Latch (CM) (edge-triggered) Peripheral Clock INTRC Source (32 s) / 64 S Q C Q To use a higher clock speed on wake-up, the INTOSC or postscaler clock sources can be selected to provide a higher clock speed by setting bits, IRCF2:IRCF0, immediately after Reset. For wake-ups from Sleep, the INTOSC or postscaler clock sources can be selected by setting the IRCF2:IRCF0 bits prior to entering Sleep mode. The FSCM will detect failures of the primary or secondary clock sources only. If the internal oscillator block fails, no failure would be detected, nor would any action be possible. 22.4.1 Both the FSCM and the WDT are clocked by the INTRC oscillator. Since the WDT operates with a separate divider and counter, disabling the WDT has no effect on the operation of the INTRC oscillator when the FSCM is enabled. As already noted, the clock source is switched to the INTOSC clock when a clock failure is detected. Depending on the frequency selected by the IRCF2:IRCF0 bits, this may mean a substantial change in the speed of code execution. If the WDT is enabled with a small prescale value, a decrease in clock speed allows a WDT time-out to occur and a subsequent device Reset. For this reason, fail-safe clock events also reset the WDT and postscaler, allowing it to start timing from when execution speed was changed and decreasing the likelihood of an erroneous time-out. 22.4.2 488 Hz (2.048 ms) Clock Failure Detected Clock failure is tested for on the falling edge of the sample clock. If a sample clock falling edge occurs while CM is still set, a clock failure has been detected (Figure 22-4). This causes the following: * the FSCM generates an oscillator fail interrupt by setting bit OSCFIF (PIR2<7>); * the device clock source is switched to the internal oscillator block (OSCCON is not updated to show the current clock source - this is the fail-safe condition); and * the WDT is reset. FSCM AND THE WATCHDOG TIMER EXITING FAIL-SAFE OPERATION The fail-safe condition is terminated by either a device Reset or by entering a power-managed mode. On Reset, the controller starts the primary clock source specified in Configuration Register 1H (with any required start-up delays that are required for the oscillator mode, such as OST or PLL timer). The INTOSC multiplexer provides the device clock until the primary clock source becomes ready (similar to a Two-Speed Start-up). The clock source is then switched to the primary clock (indicated by the OSTS bit in the OSCCON register becoming set). The Fail-Safe Clock Monitor then resumes monitoring the peripheral clock. The primary clock source may never become ready during start-up. In this case, operation is clocked by the INTOSC multiplexer. The OSCCON register will remain in its Reset state until a power-managed mode is entered. During switchover, the postscaler frequency from the internal oscillator block may not be sufficiently stable for timing sensitive applications. In these cases, it may be desirable to select another clock configuration and enter an alternate power-managed mode. This can be done to attempt a partial recovery or execute a controlled shutdown. See Section 3.1.4 "Multiple Sleep Commands" and Section 22.3.1 "Special Considerations for Using Two-Speed Start-up" for more details. (c) 2009 Microchip Technology Inc. DS39636D-page 251 PIC18F2X1X/4X1X FIGURE 22-4: FSCM TIMING DIAGRAM Sample Clock Oscillator Failure Device Clock Output CM Output (Q) Failure Detected OSCFIF CM Test Note: 22.4.3 CM Test CM Test The device clock is normally at a much higher frequency than the sample clock. The relative frequencies in this example have been chosen for clarity. FSCM INTERRUPTS IN POWER-MANAGED MODES By entering a power-managed mode, the clock multiplexer selects the clock source selected by the OSCCON register. Fail-Safe Monitoring of the powermanaged clock source resumes in the power-managed mode. If an oscillator failure occurs during power-managed operation, the subsequent events depend on whether or not the oscillator failure interrupt is enabled. If enabled (OSCFIF = 1), code execution will be clocked by the INTOSC multiplexer. An automatic transition back to the failed clock source will not occur. If the interrupt is disabled, subsequent interrupts while in Idle mode will cause the CPU to begin executing instructions while being clocked by the INTOSC source. 22.4.4 POR OR WAKE FROM SLEEP The FSCM is designed to detect oscillator failure at any point after the device has exited Power-on Reset (POR) or low-power Sleep mode. When the primary device clock is EC, RC or INTRC modes, monitoring can begin immediately following these events. For oscillator modes involving a crystal or resonator (HS, HSPLL, LP or XT), the situation is somewhat different. Since the oscillator may require a start-up time considerably longer than the FCSM sample clock time, a false clock failure may be detected. To prevent this, the internal oscillator block is automatically configured as the device clock and functions until the primary clock is stable (the OST and PLL timers have timed out). This is identical to Two-Speed Start-up mode. Once the primary clock is stable, the INTRC returns to its role as the FSCM source. Note: The same logic that prevents false oscillator failure interrupts on POR or wake from Sleep, will also prevent the detection of the oscillator's failure to start at all following these events. This can be avoided by monitoring the OSTS bit and using a timing routine to determine if the oscillator is taking too long to start. Even so, no oscillator failure interrupt will be flagged. As noted in Section 22.3.1 "Special Considerations for Using Two-Speed Start-up", it is also possible to select another clock configuration and enter an alternate power-managed mode while waiting for the primary clock to become stable. When the new powermanaged mode is selected, the primary clock is disabled. DS39636D-page 252 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 22.5 Program Verification and Code Protection The overall structure of the code protection on the PIC18 Flash devices differs significantly from other PIC(R) devices. The user program memory is divided into five blocks. One of these is a boot block of 2 Kbytes. The remainder of the memory is divided into four blocks on binary boundaries. Each of the five blocks has three code protection bits associated with them. They are: FIGURE 22-5: * Code-Protect bit (CPn) * Write-Protect bit (WRTn) * External Block Table Read bit (EBTRn) Figure 22-5 shows the program memory organization for 16- and 32-Kbyte devices and the specific code protection bit associated with each block. Figure 22-6 shows the program memory organization for 48 and 64-Kbyte devices and the specific code protection bit associated with each block. The actual locations of the bits are summarized in Table 22-3. CODE-PROTECTED PROGRAM MEMORY FOR PIC18F2410/2510/4410/4510 MEMORY SIZE/DEVICE 16 Kbytes 32 Kbytes Address (PIC18F2410/4410) (PIC18F2510/4510) Range Boot Block Boot Block Block 0 Block 0 000000h 0007FFh Block Code Protection Controlled By: CPB, WRTB, EBTRB 000800h CP0, WRT0, EBTR0 001FFFh 002000h Block 1 Block 1 CP1, WRT1, EBTR1 003FFFh 004000h CP2, WRT2, EBTR2 Block 2 005FFFh 006000h Block 3 CP3, WRT3, EBTR3 007FFFh Unimplemented Read `0's Unimplemented Read `0's (Unimplemented Memory Space) 1FFFFFh (c) 2009 Microchip Technology Inc. DS39636D-page 253 PIC18F2X1X/4X1X FIGURE 22-6: CODE-PROTECTED PROGRAM MEMORY FOR PIC18F2515/2610/4515/4610 MEMORY SIZE/DEVICE 48 Kbytes 64 Kbytes (PIC18F2515/4515) (PIC18F2610/4610) Boot Block Boot Block Block 0 Block 0 Address Range Block Code Protection Controlled By: 000000h 0007FFh CPB, WRTB, EBTRB 000800h CP0, WRT0, EBTR0 003FFFh 004000h Block 1 Block 1 CP1, WRT1, EBTR1 007FFFh 008000h Block 2 Block 2 CP2, WRT2, EBTR2 00BFFFh 00C000h Block 3 CP3, WRT3, EBTR3 00FFFFh 010000h Unimplemented Read `0's Unimplemented Read `0's (Unimplemented Memory Space) 1FFFFFh TABLE 22-3: SUMMARY OF CODE PROTECTION REGISTERS File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CP2(1) CP1 CP0 300008h CONFIG5L -- -- -- -- CP3(1,2) 300009h CONFIG5H -- CPB -- -- -- -- -- -- 30000Ah CONFIG6L -- -- -- -- WRT3(1,2) WRT2(1) WRT1 WRT0 30000Bh CONFIG6H -- WRTB WRTC -- -- -- -- -- EBTR1 EBTR0 -- -- 30000Ch CONFIG7L -- -- -- -- EBTR3 30000Dh CONFIG7H -- EBTRB -- -- -- Legend: Note 1: 2: (1,2) EBTR2 -- (1) Shaded cells are unimplemented. Unimplemented in PIC18F2410/4410 devices; maintain this bit set. Unimplemented in PIC18F2515/4515 devices; maintain this bit set. DS39636D-page 254 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 22.5.1 PROGRAM MEMORY CODE PROTECTION The program memory may be read to or written from any location using the table read and table write instructions. The Device ID may be read with table reads. The Configuration registers may be read and written with the table read and table write instructions. from a location outside of that block is not allowed to read and will result in reading `0's. Figures 22-7 through 22-10 illustrate table write and table read protection. Note: In Normal Execution mode, the CPn bits have no direct effect. CPn bits inhibit external reads and writes. The EBTRn bits control table reads. For a block of user memory with the EBTRn bit set to `0', a table read instruction that executes from within that block is allowed to read. A table read instruction that executes FIGURE 22-7: Code protection bits may only be written to a `0' from a `1' state. It is not possible to write a `1' to a bit in the `0' state. Code protection bits are only set to `1' by a full chip erase or block erase function. The full chip erase and block erase functions can only be initiated via ICSP or an external programmer. EXTERNAL BLOCK TABLE READ (EBTRn) DISALLOWED (16-KBYTE AND 32-KBYTE DEVICES) Register Values Program Memory Configuration Bit Settings 000000h 0007FFh 000800h TBLPTR = 0008FFh WRTB, EBTRB = 11 WRT0, EBTR0 = 10 001FFFh 002000h PC = 003FFEh TBLRD* WRT1, EBTR1 = 11 003FFFh 004000h WRT2, EBTR2 = 11 005FFFh 006000h WRT3, EBTR3 = 11 007FFFh Results: All table reads from external blocks to Blockn are disabled whenever EBTRn = 0. TABLAT register returns a value of `0'. (c) 2009 Microchip Technology Inc. DS39636D-page 255 PIC18F2X1X/4X1X FIGURE 22-8: EXTERNAL BLOCK TABLE READ (EBTRn) ALLOWED (16-KBYTE AND 32-KBYTE DEVICES) Register Values Program Memory Configuration Bit Settings 000000h 0007FFh 000800h TBLPTR = 0008FFh PC = 001FFEh WRTB, EBTRB = 11 WRT0, EBTR0 = 10 TBLRD* 001FFFh 002000h WRT1, EBTR1 = 11 003FFFh 004000h WRT2, EBTR2 = 11 005FFFh 006000h WRT3, EBTR3 = 11 007FFFh Results: Table reads permitted within Blockn, even when EBTRBn = 0. TABLAT register returns the value of the data at the location TBLPTR. FIGURE 22-9: EXTERNAL BLOCK TABLE READ (EBTRn) DISALLOWED (48-KBYTE AND 64-KBYTE DEVICES) Register Values Program Memory Configuration Bit Settings 000000h 0007FFh 000800h TBLPTR = 0008FFh WRTB, EBTRB = 11 WRT0, EBTR0 = 10 003FFFh 004000h PC = 003FFEh TBLRD* WRT1, EBTR1 = 11 007FFFh 008000h WRT2, EBTR2 = 11 00BFFFh 00C000h WRT3, EBTR3 = 11 00FFFFh Results: All table reads from external blocks to Blockn are disabled whenever EBTRn = 0. TABLAT register returns a value of `0'. DS39636D-page 256 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 22-10: EXTERNAL BLOCK TABLE READ (EBTRn) ALLOWED (48-KBYTE AND 64-KBYTE DEVICES) Register Values Program Memory Configuration Bit Settings 000000h WRTB, EBTRB = 11 0007FFh 000800h TBLPTR = 0008FFh PC = 001FFEh WRT0, EBTR0 = 10 TBLRD* 003FFFh 004000h WRT1, EBTR1 = 11 007FFFh 008000h WRT2, EBTR2 = 11 00BFFFh 00C000h WRT3, EBTR3 = 11 00FFFFh Results: Table reads permitted within Blockn, even when EBTRBn = 0. TABLAT register returns the value of the data at the location TBLPTR. 22.5.2 CONFIGURATION REGISTER PROTECTION The Configuration registers can be write-protected. The WRTC bit controls protection of the Configuration registers. In Normal Execution mode, the WRTC bit is readable only. WRTC can only be written via ICSP or an external programmer. 22.6 ID Locations Eight memory locations (200000h-200007h) are designated as ID locations, where the user can store checksum or other code identification numbers. These locations are both readable and writable during normal execution through the TBLRD instruction; during program/verify these locations are readable and writable. The ID locations can be read when the device is code-protected. 22.7 In-Circuit Serial Programming PIC18F2X1X/4X1X microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data and three other lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. (c) 2009 Microchip Technology Inc. 22.8 In-Circuit Debugger When the DEBUG Configuration bit is programmed to a `0', the In-Circuit Debugger functionality is enabled. This function allows simple debugging functions when used with MPLAB(R) IDE. When the microcontroller has this feature enabled, some resources are not available for general use. Table 22-4 shows which resources are required by the background debugger. TABLE 22-4: DEBUGGER RESOURCES I/O pins: RB6, RB7 Stack: 2 levels Program Memory: 512 bytes Data Memory: 10 bytes To use the In-Circuit Debugger function of the microcontroller, the design must implement In-Circuit Serial Programming connections to MCLR/VPP/RE3, VDD, VSS, RB7 and RB6. This will interface to the In-Circuit Debugger module available from Microchip or one of the third party development tool companies. DS39636D-page 257 PIC18F2X1X/4X1X 22.9 Single-Supply ICSP Programming The LVP Configuration bit enables Single-Supply ICSP Programming (formerly known as Low-Voltage ICSP Programming or LVP). When Single-Supply Programming is enabled, the microcontroller can be programmed without requiring high voltage being applied to the MCLR/VPP/RE3 pin, but the RB5/KBI1/PGM pin is then dedicated to controlling Program mode entry and is not available as a general purpose I/O pin. While programming, using Single-Supply Programming mode, VDD is applied to the MCLR/VPP/RE3 pin as in Normal Execution mode. To enter Programming mode, VDD is applied to the PGM pin. If Single-Supply ICSP Programming mode will not be used, the LVP bit can be cleared. RB5/KBI1/PGM then becomes available as the digital I/O pin, RB5. The LVP bit may be set or cleared only when using standard high-voltage programming (VIHH applied to the MCLR/ VPP/RE3 pin). Once LVP has been disabled, only the standard high-voltage programming is available and must be used to program the device. Memory that is not code-protected can be erased using either a block erase, or erased row by row, then written at any specified VDD. If code-protected memory is to be erased, a block erase is required. If a block erase is to be performed when using Low-Voltage Programming, the device must be supplied with VDD of 4.5V to 5.5V. Note 1: High-voltage programming is always available, regardless of the state of the LVP bit or the PGM pin, by applying VIHH to the MCLR pin. 2: By default, Single-Supply ICSP is enabled in unprogrammed devices (as supplied from Microchip) and erased devices. 3: When Single-Supply Programming is enabled, the RB5 pin can no longer be used as a general purpose I/O pin. 4: When LVP is enabled, externally pull the PGM pin to VSS to allow normal program execution. DS39636D-page 258 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 23.0 INSTRUCTION SET SUMMARY PIC18F2X1X/4X1X devices incorporate the standard set of 75 PIC18 core instructions, as well as an extended set of 8 new instructions for the optimization of code that is recursive or that utilizes a software stack. The extended set is discussed later in this section. 23.1 Standard Instruction Set The standard PIC18 instruction set adds many enhancements to the previous PIC(R) MCU instruction sets, while maintaining an easy migration from these PIC MCU instruction sets. Most instructions are a single program memory word (16 bits), but there are four instructions that require two program memory locations. Each single-word instruction is a 16-bit word divided into an opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The instruction set is highly orthogonal and is grouped into four basic categories: * * * * Byte-oriented operations Bit-oriented operations Literal operations Control operations The PIC18 instruction set summary in Table 23-2 lists byte-oriented, bit-oriented, literal and control operations. Table 23-1 shows the opcode field descriptions. Most byte-oriented instructions have three operands: 1. 2. 3. The file register (specified by `f') The destination of the result (specified by `d') The accessed memory (specified by `a') The file register designator `f' specifies which file register is to be used by the instruction. The destination designator `d' specifies where the result of the operation is to be placed. If `d' is zero, the result is placed in the WREG register. If `d' is one, the result is placed in the file register specified in the instruction. All bit-oriented instructions have three operands: 1. 2. 3. The file register (specified by `f') The bit in the file register (specified by `b') The accessed memory (specified by `a') The literal instructions may use some of the following operands: * A literal value to be loaded into a file register (specified by `k') * The desired FSR register to load the literal value into (specified by `f') * No operand required (specified by `--') The control instructions may use some of the following operands: * A program memory address (specified by `n') * The mode of the CALL or RETURN instructions (specified by `s') * The mode of the table read and table write instructions (specified by `m') * No operand required (specified by `--') All instructions are a single word, except for four double-word instructions. These instructions were made double-word to contain the required information in 32 bits. In the second word, the 4 MSbs are `1's. If this second word is executed as an instruction (by itself), it will execute as a NOP. All single-word instructions are executed in a single instruction cycle, unless a conditional test is true or the program counter is changed as a result of the instruction. In these cases, the execution takes two instruction cycles, with the additional instruction cycle(s) executed as a NOP. The double-word instructions execute in two instruction cycles. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 s. If a conditional test is true, or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. Two-word branch instructions (if true) would take 3 s. Figure 23-1 shows the general formats that the instructions can have. All examples use the convention `nnh' to represent a hexadecimal number. The Instruction Set Summary, shown in Table 23-2, lists the standard instructions recognized by the Microchip MPASMTM Assembler. Section 23.1.1 "Standard Instruction Set" provides a description of each instruction. The bit field designator `b' selects the number of the bit affected by the operation, while the file register designator `f' represents the number of the file in which the bit is located. (c) 2009 Microchip Technology Inc. DS39636D-page 259 PIC18F2X1X/4X1X TABLE 23-1: OPCODE FIELD DESCRIPTIONS Field Description a RAM access bit a = 0: RAM location in Access RAM (BSR register is ignored) a = 1: RAM bank is specified by BSR register bbb Bit address within an 8-bit file register (0 to 7). BSR Bank Select Register. Used to select the current RAM bank. C, DC, Z, OV, N ALU Status bits: Carry, Digit Carry, Zero, Overflow, Negative. d Destination select bit d = 0: store result in WREG d = 1: store result in file register f dest Destination: either the WREG register or the specified register file location. f 8-bit Register file address (00h to FFh) or 2-bit FSR designator (0h to 3h). fs 12-bit Register file address (000h to FFFh). This is the source address. fd 12-bit Register file address (000h to FFFh). This is the destination address. GIE Global Interrupt Enable bit. k Literal field, constant data or label (may be either an 8-bit, 12-bit or a 20-bit value). label Label name. mm The mode of the TBLPTR register for the table read and table write instructions. Only used with table read and table write instructions: * No change to register (such as TBLPTR with table reads and writes) *+ Post-Increment register (such as TBLPTR with table reads and writes) *- Post-Decrement register (such as TBLPTR with table reads and writes) Pre-Increment register (such as TBLPTR with table reads and writes) +* n The relative address (2's complement number) for relative branch instructions or the direct address for call/branch and return instructions. PC Program Counter. PCL Program Counter Low Byte. PCH Program Counter High Byte. PCLATH Program Counter High Byte Latch. PCLATU Program Counter Upper Byte Latch. PD Power-down bit. PRODH Product of Multiply High Byte. PRODL Product of Multiply Low Byte. s Fast Call/Return mode select bit s = 0: do not update into/from shadow registers s = 1: certain registers loaded into/from shadow registers (Fast mode) TBLPTR 21-bit Table Pointer (points to a Program Memory location). TABLAT 8-bit Table Latch. TO Time-out bit. TOS Top-of-Stack. u Unused or unchanged. WDT Watchdog Timer. WREG Working register (accumulator). x Don't care (`0' or `1'). The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. zs 7-bit offset value for indirect addressing of register files (source). 7-bit offset value for indirect addressing of register files (destination). zd { } Optional argument. [text] Indicates an indexed address. (text) The contents of text. [expr]<n> Specifies bit n of the register indicated by the pointer expr. Assigned to. < > Register bit field. In the set of. italics User defined term (font is Courier). DS39636D-page 260 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 23-1: GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 15 10 9 8 7 OPCODE d a Example Instruction 0 f (FILE #) ADDWF MYREG, W, B d = 0 for result destination to be WREG register d = 1 for result destination to be file register (f) a = 0 to force Access Bank a = 1 for BSR to select bank f = 8-bit file register address Byte to Byte move operations (2-word) 15 12 11 OPCODE 15 0 f (Source FILE #) 12 11 MOVFF MYREG1, MYREG2 0 f (Destination FILE #) 1111 f = 12-bit file register address Bit-oriented file register operations 15 12 11 9 8 7 OPCODE b (BIT #) a 0 BSF MYREG, bit, B f (FILE #) b = 3-bit position of bit in file register (f) a = 0 to force Access Bank a = 1 for BSR to select bank f = 8-bit file register address Literal operations 15 8 7 OPCODE 0 k (literal) MOVLW 7Fh k = 8-bit immediate value Control operations CALL, GOTO and Branch operations 15 8 7 OPCODE 15 0 n<7:0> (literal) 12 11 GOTO Label 0 n<19:8> (literal) 1111 n = 20-bit immediate value 15 8 7 OPCODE 15 S 0 CALL MYFUNC n<7:0> (literal) 12 11 0 n<19:8> (literal) 1111 S = Fast bit 15 OPCODE 15 OPCODE (c) 2009 Microchip Technology Inc. 11 10 0 BRA MYFUNC n<10:0> (literal) 8 7 n<7:0> (literal) 0 BC MYFUNC DS39636D-page 261 PIC18F2X1X/4X1X TABLE 23-2: PIC18FXXXX INSTRUCTION SET Mnemonic, Operands Description Cycles 16-Bit Instruction Word MSb LSb Status Affected Notes BYTE-ORIENTED OPERATIONS ADDWF ADDWFC ANDWF CLRF COMF CPFSEQ CPFSGT CPFSLT DECF DECFSZ DCFSNZ INCF INCFSZ INFSNZ IORWF MOVF MOVFF f, d, a f, d, a f, d, a f, a f, d, a f, a f, a f, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a fs, fd MOVWF MULWF NEGF RLCF RLNCF RRCF RRNCF SETF SUBFWB f, a f, a f, a f, d, a f, d, a f, d, a f, d, a f, a f, d, a SUBWF SUBWFB f, d, a f, d, a SWAPF TSTFSZ XORWF f, d, a f, a f, d, a Note 1: 2: 3: 4: Add WREG and f Add WREG and Carry bit to f AND WREG with f Clear f Complement f Compare f with WREG, skip = Compare f with WREG, skip > Compare f with WREG, skip < Decrement f Decrement f, Skip if 0 Decrement f, Skip if Not 0 Increment f Increment f, Skip if 0 Increment f, Skip if Not 0 Inclusive OR WREG with f Move f Move fs (source) to 1st word fd (destination) 2nd word Move WREG to f Multiply WREG with f Negate f Rotate Left f through Carry Rotate Left f (No Carry) Rotate Right f through Carry Rotate Right f (No Carry) Set f Subtract f from WREG with borrow Subtract WREG from f Subtract WREG from f with borrow Swap nibbles in f Test f, skip if 0 Exclusive OR WREG with f 1 1 1 1 1 1 (2 or 3) 1 (2 or 3) 1 (2 or 3) 1 1 (2 or 3) 1 (2 or 3) 1 1 (2 or 3) 1 (2 or 3) 1 1 2 C, DC, Z, OV, N C, DC, Z, OV, N Z, N Z Z, N None None None C, DC, Z, OV, N None None C, DC, Z, OV, N None None Z, N Z, N None 1, 2 1, 2 1,2 2 1, 2 4 4 1, 2 1, 2, 3, 4 1, 2, 3, 4 1, 2 1, 2, 3, 4 4 1, 2 1, 2 1 1 1 1 1 1 1 1 1 1 0010 0010 0001 0110 0001 0110 0110 0110 0000 0010 0100 0010 0011 0100 0001 0101 1100 1111 0110 0000 0110 0011 0100 0011 0100 0110 0101 01da 00da 01da 101a 11da 001a 010a 000a 01da 11da 11da 10da 11da 10da 00da 00da ffff ffff 111a 001a 110a 01da 01da 00da 00da 100a 01da ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff 1 1 0101 11da 0101 10da ffff ffff ffff C, DC, Z, OV, N 1, 2 ffff C, DC, Z, OV, N 1 0011 10da 1 (2 or 3) 0110 011a 1 0001 10da ffff ffff ffff ffff None ffff None ffff Z, N None None 1, 2 C, DC, Z, OV, N C, Z, N 1, 2 Z, N C, Z, N Z, N None 1, 2 C, DC, Z, OV, N 4 1, 2 When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that value present on the pins themselves. For example, if the data latch is `1' for a pin configured as input and is driven low by an external device, the data will be written back with a `0'. If this instruction is executed on the TMR0 register (and where applicable, `d' = 1), the prescaler will be cleared if assigned. If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all program memory locations have a valid instruction. DS39636D-page 262 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 23-2: PIC18FXXXX INSTRUCTION SET (CONTINUED) Mnemonic, Operands Description Cycles 16-Bit Instruction Word MSb LSb Status Affected Notes BIT-ORIENTED OPERATIONS BCF BSF BTFSC BTFSS BTG f, b, a f, b, a f, b, a f, b, a f, d, a Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set Bit Toggle f 1 1 1 (2 or 3) 1 (2 or 3) 1 1001 1000 1011 1010 0111 bbba bbba bbba bbba bbba ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff None None None None None 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 2 1 (2) 2 0010 0110 0011 0111 0101 0001 0100 0nnn 0000 110s kkkk 0000 0000 1111 kkkk 0000 xxxx 0000 0000 1nnn 0000 0000 nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn kkkk kkkk 0000 0000 kkkk kkkk 0000 xxxx 0000 0000 nnnn 1111 0001 nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn kkkk kkkk 0100 0111 kkkk kkkk 0000 xxxx 0110 0101 nnnn 1111 000s None None None None None None None None None None 1 1 1 1 2 1 2 1110 1110 1110 1110 1110 1110 1110 1101 1110 1110 1111 0000 0000 1110 1111 0000 1111 0000 0000 1101 0000 0000 2 2 1 0000 1100 0000 0000 0000 0000 kkkk 0001 0000 1, 2 1, 2 3, 4 3, 4 1, 2 CONTROL OPERATIONS BC BN BNC BNN BNOV BNZ BOV BRA BZ CALL n n n n n n n n n n, s CLRWDT DAW GOTO -- -- n NOP NOP POP PUSH RCALL RESET RETFIE -- -- -- -- n s Branch if Carry Branch if Negative Branch if Not Carry Branch if Not Negative Branch if Not Overflow Branch if Not Zero Branch if Overflow Branch Unconditionally Branch if Zero Call subroutine 1st word 2nd word Clear Watchdog Timer Decimal Adjust WREG Go to address 1st word 2nd word No Operation No Operation Pop top of return stack (TOS) Push top of return stack (TOS) Relative Call Software device Reset Return from interrupt enable RETLW RETURN SLEEP k s -- Return with literal in WREG Return from Subroutine Go into Standby mode Note 1: 2: 3: 4: 1 1 2 TO, PD C None None None None None None All GIE/GIEH, PEIE/GIEL kkkk None 001s None 0011 TO, PD 4 When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that value present on the pins themselves. For example, if the data latch is `1' for a pin configured as input and is driven low by an external device, the data will be written back with a `0'. If this instruction is executed on the TMR0 register (and where applicable, `d' = 1), the prescaler will be cleared if assigned. If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all program memory locations have a valid instruction. (c) 2009 Microchip Technology Inc. DS39636D-page 263 PIC18F2X1X/4X1X TABLE 23-2: PIC18FXXXX INSTRUCTION SET (CONTINUED) Mnemonic, Operands Description Cycles 16-Bit Instruction Word MSb LSb Status Affected Notes LITERAL OPERATIONS ADDLW ANDLW IORLW LFSR k k k f, k MOVLB MOVLW MULLW RETLW SUBLW XORLW k k k k k k Add literal and WREG AND literal with WREG Inclusive OR literal with WREG Move literal (12-bit) 2nd word to FSR(f) 1st word Move literal to BSR<3:0> Move literal to WREG Multiply literal with WREG Return with literal in WREG Subtract WREG from literal Exclusive OR literal with WREG 1 1 1 2 1 1 1 2 1 1 0000 0000 0000 1110 1111 0000 0000 0000 0000 0000 0000 1111 1011 1001 1110 0000 0001 1110 1101 1100 1000 1010 kkkk kkkk kkkk 00ff kkkk 0000 kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk C, DC, Z, OV, N Z, N Z, N None 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 1000 1001 1010 1011 1100 1101 1110 1111 None None None None None None None None None None None None C, DC, Z, OV, N Z, N DATA MEMORY PROGRAM MEMORY OPERATIONS TBLRD* TBLRD*+ TBLRD*TBLRD+* TBLWT* TBLWT*+ TBLWT*TBLWT+* Note 1: 2: 3: 4: Table Read 2 Table Read with post-increment Table Read with post-decrement Table Read with pre-increment Table Write 2 Table Write with post-increment Table Write with post-decrement Table Write with pre-increment When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that value present on the pins themselves. For example, if the data latch is `1' for a pin configured as input and is driven low by an external device, the data will be written back with a `0'. If this instruction is executed on the TMR0 register (and where applicable, `d' = 1), the prescaler will be cleared if assigned. If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Some instructions are two-word instructions. The second word of these instructions will be executed as a NOP unless the first word of the instruction retrieves the information embedded in these 16 bits. This ensures that all program memory locations have a valid instruction. DS39636D-page 264 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 23.1.1 STANDARD INSTRUCTION SET ADDLW ADD Literal to W ADDWF ADD W to f Syntax: ADDLW Syntax: ADDWF Operands: 0 f 255 d [0,1] a [0,1] Operation: (W) + (f) dest Status Affected: N, OV, C, DC, Z k Operands: 0 k 255 Operation: (W) + k W Status Affected: N, OV, C, DC, Z Encoding: 0000 1111 kkkk kkkk Description: The contents of W are added to the 8-bit literal `k' and the result is placed in W. Words: 1 Cycles: 1 Encoding: 0010 Q1 Q2 Q3 Q4 Read literal `k' Process Data Write to W Example: ADDLW = 25h ffff Words: 1 Cycles: 1 Before Instruction W ffff Add W to register `f'. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. 15h W = 10h After Instruction 01da Description: Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: ADDWF REG, 0, 0 Before Instruction W = REG = After Instruction W REG Note: = = 17h 0C2h 0D9h 0C2h All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in symbolic addressing. If a label is used, the instruction format then becomes: {label} instruction argument(s). (c) 2009 Microchip Technology Inc. DS39636D-page 265 PIC18F2X1X/4X1X ADDWFC ADD W and Carry bit to f ANDLW AND Literal with W Syntax: ADDWFC Syntax: ANDLW Operands: 0 f 255 d [0,1] a [0,1] f {,d {,a}} Operation: (W) + (f) + (C) dest Status Affected: N,OV, C, DC, Z Encoding: 0010 Description: 00da ffff Add W, the Carry flag and data memory location `f'. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed in data memory location `f'. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Operands: 0 k 255 Operation: (W) .AND. k W Status Affected: N, Z Encoding: ffff k 0000 1011 kkkk kkkk Description: The contents of W are AND'ed with the 8-bit literal `k'. The result is placed in W. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal `k' Process Data Write to W Example: ANDLW 05Fh Before Instruction W = After Instruction W = A3h 03h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: ADDWFC Before Instruction Carry bit = REG = W = After Instruction Carry bit = REG = W = DS39636D-page 266 REG, 0, 1 1 02h 4Dh 0 02h 50h (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X ANDWF AND W with f BC Branch if Carry Syntax: ANDWF Syntax: BC Operands: 0 f 255 d [0,1] a [0,1] Operands: -128 n 127 Operation: if Carry bit is `1' (PC) + 2 + 2n PC Status Affected: None f {,d {,a}} Operation: (W) .AND. (f) dest Status Affected: N, Z Encoding: 0001 Description: Encoding: 01da ffff ffff The contents of W are AND'ed with register `f'. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: ANDWF REG, 0, 0 Before Instruction W = REG = After Instruction W REG = = 17h C2h 02h C2h (c) 2009 Microchip Technology Inc. n 1110 Description: 0010 nnnn nnnn If the Carry bit is `1', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data Write to PC No operation No operation No operation No operation If No Jump: Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data No operation Example: HERE Before Instruction PC After Instruction If Carry PC If Carry PC BC 5 = address (HERE) = = = = 1; address (HERE + 12) 0; address (HERE + 2) DS39636D-page 267 PIC18F2X1X/4X1X BCF Bit Clear f BN Branch if Negative Syntax: BCF Syntax: BN Operands: 0 f 255 0b7 a [0,1] Operands: -128 n 127 Operation: if Negative bit is `1' (PC) + 2 + 2n PC Status Affected: None f, b {,a} Operation: 0 f<b> Status Affected: None Encoding: Encoding: 1001 Description: bbba ffff ffff Bit `b' in register `f' is cleared. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' Example: BCF Before Instruction FLAG_REG = After Instruction FLAG_REG = DS39636D-page 268 FLAG_REG, 7, 0 n 1110 Description: 0110 nnnn nnnn If the Negative bit is `1', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data Write to PC No operation No operation No operation No operation If No Jump: Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data No operation C7h 47h Example: HERE Before Instruction PC After Instruction If Negative PC If Negative PC BN Jump = address (HERE) = = = = 1; address (Jump) 0; address (HERE + 2) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X BNC Branch if Not Carry BNN Branch if Not Negative Syntax: BNC Syntax: BNN n n Operands: -128 n 127 Operands: -128 n 127 Operation: if Carry bit is `0' (PC) + 2 + 2n PC Operation: if Negative bit is `0' (PC) + 2 + 2n PC Status Affected: None Status Affected: None Encoding: 1110 0011 nnnn nnnn Encoding: 1110 0111 nnnn nnnn Description: If the Carry bit is `0', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Description: If the Negative bit is `0', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Words: 1 Cycles: 1(2) Cycles: 1(2) Q Cycle Activity: If Jump: Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data Write to PC Decode Read literal `n' Process Data Write to PC No operation No operation No operation No operation No operation No operation No operation No operation Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data No operation Decode Read literal `n' Process Data No operation If No Jump: Example: If No Jump: HERE Before Instruction PC After Instruction If Carry PC If Carry PC BNC Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) (c) 2009 Microchip Technology Inc. Example: HERE Before Instruction PC After Instruction If Negative PC If Negative PC BNN Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) DS39636D-page 269 PIC18F2X1X/4X1X BNOV Branch if Not Overflow BNZ Branch if Not Zero Syntax: BNOV Syntax: BNZ n n Operands: -128 n 127 Operands: -128 n 127 Operation: if Overflow bit is `0' (PC) + 2 + 2n PC Operation: if Zero bit is `0' (PC) + 2 + 2n PC Status Affected: None Status Affected: None Encoding: 1110 0101 nnnn nnnn Encoding: 1110 0001 nnnn nnnn Description: If the Overflow bit is `0', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Description: If the Zero bit is `0', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Words: 1 Cycles: 1(2) Cycles: 1(2) Q Cycle Activity: If Jump: Q Cycle Activity: If Jump: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data Write to PC Decode Read literal `n' Process Data Write to PC No operation No operation No operation No operation No operation No operation No operation No operation Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data No operation Decode Read literal `n' Process Data No operation If No Jump: If No Jump: Example: HERE Before Instruction PC After Instruction If Overflow PC If Overflow PC DS39636D-page 270 BNOV Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) Example: HERE Before Instruction PC After Instruction If Zero PC If Zero PC BNZ Jump = address (HERE) = = = = 0; address (Jump) 1; address (HERE + 2) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X BRA Unconditional Branch BSF Bit Set f Syntax: BRA Syntax: BSF Operands: -1024 n 1023 Operands: Operation: (PC) + 2 + 2n PC Status Affected: None 0 f 255 0b7 a [0,1] Operation: 1 f<b> Status Affected: None Encoding: n 1101 Description: 0nnn nnnn nnnn Add the 2's complement number `2n' to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is a two-cycle instruction. Words: 1 Cycles: 2 Encoding: 1000 Q1 Q2 Q3 Q4 Read literal `n' Process Data Write to PC No operation No operation No operation No operation Example: HERE Before Instruction PC After Instruction PC BRA Jump = address (HERE) = address (Jump) ffff ffff Bit `b' in register `f' is set. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' Example: BSF Before Instruction FLAG_REG After Instruction FLAG_REG (c) 2009 Microchip Technology Inc. bbba Description: Q Cycle Activity: Decode f, b {,a} FLAG_REG, 7, 1 = 0Ah = 8Ah DS39636D-page 271 PIC18F2X1X/4X1X BTFSC Bit Test File, Skip if Clear BTFSS Bit Test File, Skip if Set Syntax: BTFSC f, b {,a} Syntax: BTFSS f, b {,a} Operands: 0 f 255 0b7 a [0,1] Operands: 0 f 255 0b<7 a [0,1] Operation: skip if (f<b>) = 0 Operation: skip if (f<b>) = 1 Status Affected: None Status Affected: None Encoding: 1011 Description: bbba ffff ffff Encoding: 1010 If bit `b' in register `f' is `0', then the next instruction is skipped. If bit `b' is `0', then the next instruction fetched during the current instruction execution is discarded and a NOP is executed instead, making this a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Description: Words: 1 Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Cycles: 1(2) Note: Q Cycle Activity: bbba ffff ffff If bit `b' in register `f' is `1', then the next instruction is skipped. If bit `b' is `1', then the next instruction fetched during the current instruction execution is discarded and a NOP is executed instead, making this a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data No operation Decode Read register `f' Process Data No operation Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation If skip: If skip: If skip and followed by 2-word instruction: If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE FALSE TRUE Before Instruction PC After Instruction If FLAG<1> PC If FLAG<1> PC DS39636D-page 272 BTFSC : : FLAG, 1, 0 = address (HERE) = = = = 0; address (TRUE) 1; address (FALSE) Example: HERE FALSE TRUE Before Instruction PC After Instruction If FLAG<1> PC If FLAG<1> PC BTFSS : : FLAG, 1, 0 = address (HERE) = = = = 0; address (FALSE) 1; address (TRUE) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X BTG Bit Toggle f BOV Branch if Overflow Syntax: BTG f, b {,a} Syntax: BOV Operands: 0 f 255 0b<7 a [0,1] Operands: -128 n 127 Operation: if Overflow bit is `1' (PC) + 2 + 2n PC Status Affected: None Operation: (f<b>) f<b> Status Affected: None Encoding: 0111 Description: Encoding: bbba ffff ffff Bit `b' in data memory location `f' is inverted. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. n 1110 0100 nnnn nnnn Description: If the Overflow bit is `1', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: If Jump: Words: 1 Q1 Q2 Q3 Q4 Cycles: 1 Decode Read literal `n' Process Data Write to PC No operation No operation No operation No operation Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' Example: BTG PORTC, 4, 0 Before Instruction: PORTC = 0111 0101 [75h] After Instruction: PORTC = 0110 0101 [65h] (c) 2009 Microchip Technology Inc. If No Jump: Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data No operation Example: HERE Before Instruction PC After Instruction If Overflow PC If Overflow PC BOV Jump = address (HERE) = = = = 1; address (Jump) 0; address (HERE + 2) DS39636D-page 273 PIC18F2X1X/4X1X BZ Branch if Zero CALL Subroutine Call Syntax: BZ Syntax: CALL k {,s} n Operands: -128 n 127 Operands: Operation: if Zero bit is `1' (PC) + 2 + 2n PC 0 k 1048575 s [0,1] Operation: Status Affected: None (PC) + 4 TOS, k PC<20:1>, if s = 1 (W) WS, (STATUS) STATUSS, (BSR) BSRS Status Affected: None Encoding: 1110 Description: 0000 nnnn nnnn If the Zero bit is `1', then the program will branch. The 2's complement number `2n' is added to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC + 2 + 2n. This instruction is then a two-cycle instruction. Words: 1 Cycles: 1(2) Encoding: 1st word (k<7:0>) 2nd word(k<19:8>) Q1 Q2 Q3 Q4 Read literal `n' Process Data Write to PC No operation No operation No operation No operation If No Jump: Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data No operation Example: HERE Before Instruction PC After Instruction If Zero PC If Zero PC DS39636D-page 274 BZ k7kkk kkkk 110s k19kkk Subroutine call of entire 2-Mbyte memory range. First, return address (PC + 4) is pushed onto the return stack. If `s' = 1, the W, STATUS and BSR registers are also pushed into their respective shadow registers, WS, STATUSS and BSRS. If `s' = 0, no update occurs (default). Then, the 20-bit value `k' is loaded into PC<20:1>. CALL is a two-cycle instruction. Words: 2 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal `k'<7:0>, Push PC to stack Read literal `k'<19:8>, Write to PC No operation No operation No operation No operation Jump = address (HERE) = = = = 1; address (Jump) 0; address (HERE + 2) kkkk0 kkkk8 Description: Q Cycle Activity: If Jump: Decode 1110 1111 Example: HERE Before Instruction PC = After Instruction PC = TOS = WS = BSRS = STATUSS = CALL THERE,1 address (HERE) address (THERE) address (HERE + 4) W BSR STATUS (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X CLRF Clear f Syntax: CLRF Operands: 0 f 255 a [0,1] f {,a} Operation: 000h f 1Z Status Affected: Z Encoding: 0110 Description: 101a ffff ffff Clears the contents of the specified register. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' CLRF Before Instruction FLAG_REG After Instruction FLAG_REG Clear Watchdog Timer Syntax: CLRWDT Operands: None Operation: 000h WDT, 000h WDT postscaler, 1 TO, 1 PD Status Affected: TO, PD Encoding: FLAG_REG,1 = 5Ah = 00h (c) 2009 Microchip Technology Inc. 0000 Description: 0000 0000 0100 CLRWDT instruction resets the Watchdog Timer. It also resets the postscaler of the WDT. Status bits TO and PD are set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation Process Data No operation Example: Q Cycle Activity: Example: CLRWDT CLRWDT Before Instruction WDT Counter After Instruction WDT Counter WDT Postscaler TO PD = ? = = = = 00h 0 1 1 DS39636D-page 275 PIC18F2X1X/4X1X COMF Complement f CPFSEQ Compare f with W, Skip if f = W Syntax: COMF Syntax: CPFSEQ Operands: 0 f 255 a [0,1] Operation: (f) - (W), skip if (f) = (W) (unsigned comparison) Status Affected: None f {,d {,a}} 0 f 255 d [0,1] a [0,1] Operands: Operation: ( f ) dest Status Affected: N, Z Encoding: 0001 11da ffff ffff Description: The contents of register `f' are complemented. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Encoding: 0110 f {,a} 001a ffff ffff Description: Compares the contents of data memory location `f' to the contents of W by performing an unsigned subtraction. If `f' = W, then the fetched instruction is discarded and a NOP is executed instead, making this a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Example: COMF Before Instruction REG = After Instruction REG = W = REG, 0, 0 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data No operation 13h If skip: 13h ECh Q1 Q2 Q3 No No No operation operation operation If skip and followed by 2-word instruction: Q1 Q2 Q3 No No No operation operation operation No No No operation operation operation Example: DS39636D-page 276 HERE NEQUAL EQUAL Q4 No operation Q4 No operation No operation CPFSEQ REG, 0 : : Before Instruction PC Address W REG After Instruction = = = HERE ? ? If REG PC If REG PC = = = W; Address (EQUAL) W; Address (NEQUAL) (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X CPFSGT Compare f with W, Skip if f > W CPFSLT Compare f with W, Skip if f < W Syntax: CPFSGT Syntax: CPFSLT Operands: 0 f 255 a [0,1] Operands: 0 f 255 a [0,1] Operation: (f) - (W), skip if (f) > (W) (unsigned comparison) Operation: (f) - (W), skip if (f) < (W) (unsigned comparison) Status Affected: None Status Affected: None Encoding: 0110 Description: f {,a} 010a ffff ffff Compares the contents of data memory location `f' to the contents of the W by performing an unsigned subtraction. If the contents of `f' are greater than the contents of WREG, then the fetched instruction is discarded and a NOP is executed instead, making this a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Encoding: Q2 Read register `f' Q3 Process Data Q4 No operation Q1 Q2 Q3 No No No operation operation operation If skip and followed by 2-word instruction: Q1 Q2 Q3 No No No operation operation operation No No No operation operation operation Q4 No operation Example: HERE NGREATER GREATER CPFSGT REG, 0 : : Before Instruction PC W After Instruction = = Address (HERE) ? If REG PC If REG PC > = = W; Address (GREATER) W; Address (NGREATER) (c) 2009 Microchip Technology Inc. 000a ffff ffff Compares the contents of data memory location `f' to the contents of W by performing an unsigned subtraction. If the contents of `f' are less than the contents of W, then the fetched instruction is discarded and a NOP is executed instead, making this a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data No operation If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: If skip: Q4 No operation No operation 0110 Description: Q Cycle Activity: Q1 Decode f {,a} Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NLESS LESS CPFSLT REG, 1 : : Before Instruction PC W After Instruction = = Address (HERE) ? If REG PC If REG PC < = = W; Address (LESS) W; Address (NLESS) DS39636D-page 277 PIC18F2X1X/4X1X DAW Decimal Adjust W Register DECF Decrement f Syntax: DAW Syntax: DECF f {,d {,a}} Operands: None Operands: Operation: If [W<3:0> > 9] or [DC = 1] then (W<3:0>) + 6 W<3:0>; else (W<3:0>) W<3:0>; 0 f 255 d [0,1] a [0,1] Operation: (f) - 1 dest Status Affected: C, DC, N, OV, Z If [W<7:4> + DC > 9] or [C = 1] then (W<7:4>) + 6 + DC W<7:4> ; else (W<7:4>) + DC W<7:4> Status Affected: Encoding: 0000 0000 0000 DAW adjusts the eight-bit value in W, resulting from the earlier addition of two variables (each in packed BCD format) and produces a correct packed BCD result. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register W Process Data Write W Example 1: DAW = = = A5h 0 0 05h 1 0 ffff Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Before Instruction W = C = DC = After Instruction ffff Decrement register `f'. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. 0111 Description: 01da Description: C Encoding: W C DC Example 2: 0000 Example: DECF Before Instruction CNT = Z = After Instruction CNT = Z = CNT, 1, 0 01h 0 00h 1 Before Instruction W = C = DC = After Instruction W C DC = = = DS39636D-page 278 CEh 0 0 34h 1 0 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X DECFSZ Decrement f, Skip if 0 DCFSNZ Decrement f, Skip if not 0 Syntax: DECFSZ f {,d {,a}} Syntax: DCFSNZ Operands: 0 f 255 d [0,1] a [0,1] Operands: 0 f 255 d [0,1] a [0,1] Operation: (f) - 1 dest, skip if result = 0 Operation: (f) - 1 dest, skip if result 0 Status Affected: None Status Affected: None Encoding: 0010 11da ffff ffff Description: The contents of register `f' are decremented. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If the result is `0', the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Encoding: 0100 Description: 11da Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Words: 1 Cycles: 1(2) Note: Q1 Q2 Q3 Q4 No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation DECFSZ GOTO CNT, 1, 1 LOOP Example: HERE CONTINUE Before Instruction PC = After Instruction CNT = If CNT = PC = If CNT PC = Address (HERE) CNT - 1 0; Address (CONTINUE) 0; Address (HERE + 2) (c) 2009 Microchip Technology Inc. ffff 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination If skip: No operation ffff The contents of register `f' are decremented. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If the result is not `0', the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Q Cycle Activity: Q1 f {,d {,a}} If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE ZERO NZERO Before Instruction TEMP After Instruction TEMP If TEMP PC If TEMP PC DCFSNZ : : TEMP, 1, 0 = ? = = = = TEMP - 1, 0; Address (ZERO) 0; Address (NZERO) DS39636D-page 279 PIC18F2X1X/4X1X GOTO Unconditional Branch INCF Increment f Syntax: GOTO k Syntax: INCF Operands: 0 k 1048575 Operands: Operation: k PC<20:1> Status Affected: None 0 f 255 d [0,1] a [0,1] Operation: (f) + 1 dest Status Affected: C, DC, N, OV, Z Encoding: 1st word (k<7:0>) 2nd word(k<19:8>) 1110 1111 1111 k19kkk k7kkk kkkk kkkk0 kkkk8 GOTO allows an unconditional branch Description: Encoding: 0010 2 Cycles: 2 Q1 Q2 Q3 Q4 Read literal `k'<7:0>, No operation Read literal `k'<19:8>, Write to PC No operation No operation No operation No operation ffff ffff The contents of register `f' are incremented. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Decode 10da Description: anywhere within entire 2-Mbyte memory range. The 20-bit value `k' is loaded into PC<20:1>. GOTO is always a two-cycle instruction. Words: f {,d {,a}} Q Cycle Activity: Example: GOTO THERE After Instruction PC = Address (THERE) Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: INCF Before Instruction CNT = Z = C = DC = After Instruction CNT = Z = C = DC = DS39636D-page 280 CNT, 1, 0 FFh 0 ? ? 00h 1 1 1 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X INCFSZ Increment f, Skip if 0 INFSNZ Syntax: INCFSZ Syntax: INFSNZ 0 f 255 d [0,1] a [0,1] f {,d {,a}} Increment f, Skip if not 0 f {,d {,a}} Operands: 0 f 255 d [0,1] a [0,1] Operands: Operation: (f) + 1 dest, skip if result = 0 Operation: (f) + 1 dest, skip if result 0 Status Affected: None Status Affected: None Encoding: 0011 11da ffff ffff Encoding: 0100 Description: ffff ffff The contents of register `f' are incremented. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If the result is not `0', the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Description: The contents of register `f' are incremented. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f'. (default) If the result is `0', the next instruction, which is already fetched, is discarded and a NOP is executed instead, making it a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. Cycles: 1(2) Note: Q Cycle Activity: 10da 3 cycles if skip and followed by a 2-word instruction. Q Cycle Activity: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Decode Read register `f' Process Data Write to destination Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation If skip: If skip: If skip and followed by 2-word instruction: If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NZERO ZERO Before Instruction PC = After Instruction CNT = If CNT = PC = If CNT PC = INCFSZ : : Address (HERE) CNT + 1 0; Address (ZERO) 0; Address (NZERO) (c) 2009 Microchip Technology Inc. CNT, 1, 0 Example: HERE ZERO NZERO Before Instruction PC = After Instruction REG = If REG PC = If REG = PC = INFSNZ REG, 1, 0 Address (HERE) REG + 1 0; Address (NZERO) 0; Address (ZERO) DS39636D-page 281 PIC18F2X1X/4X1X IORLW Inclusive OR Literal with W IORWF Inclusive OR W with f Syntax: IORLW k Syntax: IORWF Operands: 0 k 255 Operands: Operation: (W) .OR. k W Status Affected: N, Z 0 f 255 d [0,1] a [0,1] Operation: (W) .OR. (f) dest Status Affected: N, Z Encoding: 0000 1001 kkkk kkkk Description: The contents of W are ORed with the eight-bit literal `k'. The result is placed in W. Words: 1 Cycles: 1 Encoding: 0001 Q1 Q2 Q3 Q4 Read literal `k' Process Data Write to W Example: IORLW W = ffff Words: 1 Cycles: 1 35h 9Ah BFh ffff Inclusive OR W with register `f'. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Before Instruction W = After Instruction 00da Description: Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: IORWF Before Instruction RESULT = W = After Instruction RESULT = W = DS39636D-page 282 RESULT, 0, 1 13h 91h 13h 93h (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X LFSR Load FSR MOVF Move f Syntax: LFSR f, k Syntax: MOVF Operands: 0f2 0 k 4095 Operands: Operation: k FSRf 0 f 255 d [0,1] a [0,1] Status Affected: None Operation: f dest Status Affected: N, Z Encoding: 1110 1111 1110 0000 00ff k7kkk k11kkk kkkk Description: The 12-bit literal `k' is loaded into the File Select Register pointed to by `f'. Words: 2 Cycles: 2 Encoding: 0101 Q1 Q2 Q3 Q4 Read literal `k' MSB Process Data Write literal `k' MSB to FSRfH Decode Read literal `k' LSB Process Data Write literal `k' to FSRfL Example: After Instruction FSR2H FSR2L 03h ABh ffff ffff The contents of register `f' are moved to a destination dependent upon the status of `d'. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). Location `f' can be anywhere in the 256-byte bank. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 LFSR 2, 3ABh = = 00da Description: Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write W Example: MOVF Before Instruction REG W After Instruction REG W (c) 2009 Microchip Technology Inc. REG, 0, 0 = = 22h FFh = = 22h 22h DS39636D-page 283 PIC18F2X1X/4X1X MOVFF Move f to f MOVLB Move Literal to Low Nibble in BSR Syntax: MOVFF fs,fd Syntax: MOVLW k Operands: 0 fs 4095 0 fd 4095 Operands: 0 k 255 Operation: k BSR None Operation: (fs) fd Status Affected: Status Affected: None Encoding: Encoding: 1st word (source) 2nd word (destin.) 1100 1111 Description: ffff ffff ffff ffff ffffs ffffd The contents of source register `fs' are moved to destination register `fd'. Location of source `fs' can be anywhere in the 4096-byte data space (000h to FFFh) and location of destination `fd' can also be anywhere from 000h to FFFh. Either source or destination can be W (a useful special situation). MOVFF is particularly useful for transferring a data memory location to a peripheral register (such as the transmit buffer or an I/O port). The MOVFF instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. Words: 2 Cycles: 2 (3) 0000 0001 kkkk kkkk Description: The eight-bit literal `k' is loaded into the Bank Select Register (BSR). The value of BSR<7:4> always remains `0', regardless of the value of k7:k4. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal `k' Process Data Write literal `k' to BSR MOVLB 5 Example: Before Instruction BSR Register = After Instruction BSR Register = 02h 05h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' (src) Process Data No operation Decode No operation No operation Write register `f' (dest) No dummy read Example: MOVFF Before Instruction REG1 REG2 After Instruction REG1 REG2 DS39636D-page 284 REG1, REG2 = = 33h 11h = = 33h 33h (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X MOVLW Move Literal to W MOVWF Move W to f Syntax: MOVLW k Syntax: MOVWF Operands: 0 k 255 Operands: Operation: kW 0 f 255 a [0,1] Status Affected: None Encoding: 0000 Description: 1110 kkkk kkkk The eight-bit literal `k' is loaded into W. Words: 1 Cycles: 1 Operation: (W) f Status Affected: None Encoding: 0110 Q1 Q2 Q3 Q4 Read literal `k' Process Data Write to W Example: MOVLW = ffff ffff Move data from W to register `f'. Location `f' can be anywhere in the 256-byte bank. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 5Ah After Instruction W 111a Description: Q Cycle Activity: Decode f {,a} 5Ah Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' Example: MOVWF REG, 0 Before Instruction W = REG = After Instruction W REG (c) 2009 Microchip Technology Inc. = = 4Fh FFh 4Fh 4Fh DS39636D-page 285 PIC18F2X1X/4X1X MULLW Multiply Literal with W MULWF Multiply W with f Syntax: MULLW Syntax: MULWF Operands: 0 f 255 a [0,1] Operation: (W) x (f) PRODH:PRODL Status Affected: None k Operands: 0 k 255 Operation: (W) x k PRODH:PRODL Status Affected: None Encoding: 0000 Description: 1101 kkkk kkkk An unsigned multiplication is carried out between the contents of W and the 8-bit literal `k'. The 16-bit result is placed in PRODH:PRODL register pair. PRODH contains the high byte. W is unchanged. None of the status flags are affected. Note that neither overflow nor carry is possible in this operation. A zero result is possible but not detected. Words: 1 Cycles: 1 Encoding: 0000 Q1 Q2 Q3 Q4 Read literal `k' Process Data Write registers PRODH: PRODL Example: MULLW W PRODH PRODL After Instruction W PRODH PRODL = = = E2h ? ? = = = E2h ADh 08h ffff ffff An unsigned multiplication is carried out between the contents of W and the register file location `f'. The 16-bit result is stored in the PRODH:PRODL register pair. PRODH contains the high byte. Both W and `f' are unchanged. None of the status flags are affected. Note that neither overflow nor carry is possible in this operation. A zero result is possible but not detected. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 0C4h Before Instruction 001a Description: Q Cycle Activity: Decode f {,a} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write registers PRODH: PRODL Example: MULWF REG, 1 Before Instruction W REG PRODH PRODL After Instruction W REG PRODH PRODL DS39636D-page 286 = = = = C4h B5h ? ? = = = = C4h B5h 8Ah 94h (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X NEGF Negate f NOP No Operation Syntax: NEGF Syntax: NOP Operands: 0 f 255 a [0,1] f {,a} Operands: None Operation: No operation None Operation: (f)+1f Status Affected: Status Affected: N, OV, C, DC, Z Encoding: Encoding: 0110 Description: 110a ffff Location `f' is negated using two's complement. The result is placed in the data memory location `f'. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 0000 1111 ffff 0000 xxxx Description: No operation. Words: 1 Cycles: 1 0000 xxxx 0000 xxxx Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation No operation No operation Example: None. Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' Example: NEGF Before Instruction REG = After Instruction REG = REG, 1 0011 1010 [3Ah] 1100 0110 [C6h] (c) 2009 Microchip Technology Inc. DS39636D-page 287 PIC18F2X1X/4X1X POP Pop Top of Return Stack PUSH Push Top of Return Stack Syntax: POP Syntax: PUSH Operands: None Operands: None Operation: (TOS) bit bucket Operation: (PC + 2) TOS Status Affected: None Status Affected: None Encoding: 0000 0000 0000 0110 Description: The TOS value is pulled off the return stack and is discarded. The TOS value then becomes the previous value that was pushed onto the return stack. This instruction is provided to enable the user to properly manage the return stack to incorporate a software stack. Words: 1 Cycles: 1 Encoding: 0000 0101 The PC + 2 is pushed onto the top of the return stack. The previous TOS value is pushed down on the stack. This instruction allows implementing a software stack by modifying TOS and then pushing it onto the return stack. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation POP TOS value No operation POP GOTO NEW Q1 Q2 Q3 Q4 Decode PUSH PC + 2 onto return stack No operation No operation Example: Before Instruction TOS Stack (1 level down) = = 0031A2h 014332h After Instruction TOS PC = = 014332h NEW DS39636D-page 288 0000 Description: Q Cycle Activity: Example: 0000 PUSH Before Instruction TOS PC = = 345Ah 0124h After Instruction PC TOS Stack (1 level down) = = = 0126h 0126h 345Ah (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X RCALL Relative Call RESET Reset Syntax: RCALL Syntax: RESET n Operands: -1024 n 1023 Operands: None Operation: (PC) + 2 TOS, (PC) + 2 + 2n PC Operation: Reset all registers and flags that are affected by a MCLR Reset. Status Affected: None Status Affected: All Encoding: 1101 Description: 1nnn nnnn nnnn Subroutine call with a jump up to 1K from the current location. First, return address (PC+2) is pushed onto the stack. Then, add the 2's complement number `2n' to the PC. Since the PC will have incremented to fetch the next instruction, the new address will be PC+2+2n. This instruction is a two-cycle instruction. Words: 1 Cycles: 2 Encoding: 0000 Q1 Q2 Q3 Q4 Decode Read literal `n' Process Data Write to PC No operation No operation 1111 1111 This instruction provides a way to execute a MCLR Reset in software. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Start Reset No operation No operation Example: Q Cycle Activity: 0000 Description: After Instruction Registers = Flags* = RESET Reset Value Reset Value Push PC to stack No operation Example: No operation HERE RCALL Jump Before Instruction PC = Address (HERE) After Instruction PC = Address (Jump) TOS = Address (HERE + 2) (c) 2009 Microchip Technology Inc. DS39636D-page 289 PIC18F2X1X/4X1X RETFIE Return from Interrupt RETLW Return Literal to W Syntax: RETFIE {s} Syntax: RETLW k Operands: s [0,1] Operands: 0 k 255 Operation: (TOS) PC, 1 GIE/GIEH or PEIE/GIEL, if s = 1 (WS) W, (STATUSS) STATUS, (BSRS) BSR, PCLATU, PCLATH are unchanged. Operation: k W, (TOS) PC, PCLATU, PCLATH are unchanged Status Affected: None Status Affected: 0000 0000 Description: 0000 0001 Words: 1 Cycles: 2 Q Cycle Activity: kkkk kkkk W is loaded with the eight-bit literal `k'. The program counter is loaded from the top of the stack (the return address). The high address latch (PCLATH) remains unchanged. Words: 1 Cycles: 2 000s Return from Interrupt. Stack is popped and Top-of-Stack (TOS) is loaded into the PC. Interrupts are enabled by setting either the high or low priority global interrupt enable bit. If `s' = 1, the contents of the shadow registers WS, STATUSS and BSRS are loaded into their corresponding registers, W, STATUS and BSR. If `s' = 0, no update of these registers occurs (default). 1100 Description: GIE/GIEH, PEIE/GIEL. Encoding: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal `k' Process Data POP PC from stack, Write to W No operation No operation No operation No operation Example: Q1 Q2 Q3 Q4 Decode No operation No operation POP PC from stack Set GIEH or GIEL No operation Encoding: No operation Example: RETFIE After Interrupt PC W BSR STATUS GIE/GIEH, PEIE/GIEL DS39636D-page 290 No operation No operation 1 = = = = = TOS WS BSRS STATUSS 1 CALL TABLE ; ; ; ; : TABLE ADDWF PCL ; RETLW k0 ; RETLW k1 ; : : RETLW kn ; Before Instruction W = After Instruction W = W contains table offset value W now has table value W = offset Begin table End of table 07h value of kn (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X RETURN Return from Subroutine RLCF Rotate Left f through Carry Syntax: RETURN {s} Syntax: RLCF Operands: s [0,1] Operands: Operation: (TOS) PC, if s = 1 (WS) W, (STATUSS) STATUS, (BSRS) BSR, PCLATU, PCLATH are unchanged 0 f 255 d [0,1] a [0,1] Operation: (f<n>) dest<n + 1>, (f<7>) C, (C) dest<0> Status Affected: C, N, Z Status Affected: None Encoding: 0000 Encoding: 0000 0001 001s Description: Return from subroutine. The stack is popped and the top of the stack (TOS) is loaded into the program counter. If `s'= 1, the contents of the shadow registers WS, STATUSS and BSRS are loaded into their corresponding registers, W, STATUS and BSR. If `s' = 0, no update of these registers occurs (default). Words: 1 Cycles: 2 0011 Description: Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation Process Data POP PC from stack No operation No operation No operation No operation f {,d {,a}} 01da ffff ffff The contents of register `f' are rotated one bit to the left through the Carry flag. If `d' is `0', the result is placed in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. register f C Words: 1 Cycles: 1 Q Cycle Activity: Example: RETURN After Instruction: PC = TOS Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: Before Instruction REG = C = After Instruction REG = W = C = (c) 2009 Microchip Technology Inc. RLCF REG, 0, 0 1110 0110 0 1110 0110 1100 1100 1 DS39636D-page 291 PIC18F2X1X/4X1X RLNCF Rotate Left f (no carry) RRCF Rotate Right f through Carry Syntax: RLNCF Syntax: RRCF Operands: 0 f 255 d [0,1] a [0,1] Operands: 0 f 255 d [0,1] a [0,1] Operation: (f<n>) dest<n + 1>, (f<7>) dest<0> Operation: Status Affected: N, Z (f<n>) dest<n - 1>, (f<0>) C, (C) dest<7> Status Affected: C, N, Z Encoding: 0100 Description: f {,d {,a}} 01da ffff ffff The contents of register `f' are rotated one bit to the left. If `d' is `0', the result is placed in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Encoding: 0011 Description: register f Words: 1 Cycles: 1 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Before Instruction REG = After Instruction REG = DS39636D-page 292 00da RLNCF Words: 1 Cycles: 1 0101 0111 ffff register f Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination REG, 1, 0 1010 1011 ffff The contents of register `f' are rotated one bit to the right through the Carry flag. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. C Q Cycle Activity: Example: f {,d {,a}} Example: RRCF Before Instruction REG = C = After Instruction REG = W = C = REG, 0, 0 1110 0110 0 1110 0110 0111 0011 0 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X RRNCF Rotate Right f (no carry) SETF Syntax: RRNCF Syntax: SETF Operands: 0 f 255 d [0,1] a [0,1] Operands: 0 f 255 a [0,1] Operation: FFh f Operation: (f<n>) dest<n - 1>, (f<0>) dest<7> Status Affected: None Status Affected: f {,d {,a}} Encoding: N, Z Encoding: 0100 Description: 00da ffff ffff The contents of register `f' are rotated one bit to the right. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed back in register `f' (default). If `a' is `0', the Access Bank will be selected, overriding the BSR value. If `a' is `1', then the bank will be selected as per the BSR value (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. register f Words: 1 Cycles: 1 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination RRNCF Before Instruction REG = After Instruction REG = Example 2: f {,a} 0110 100a ffff ffff Description: The contents of the specified register are set to FFh. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write register `f' Example: Q Cycle Activity: Example 1: Set f SETF Before Instruction REG After Instruction REG REG,1 = 5Ah = FFh REG, 1, 0 1101 0111 1110 1011 RRNCF REG, 0, 0 Before Instruction W = REG = After Instruction ? 1101 0111 = = 1110 1011 1101 0111 W REG (c) 2009 Microchip Technology Inc. DS39636D-page 293 PIC18F2X1X/4X1X SLEEP Enter Sleep mode SUBFWB Subtract f from W with Borrow Syntax: SLEEP Syntax: SUBFWB Operands: None Operands: Operation: 00h WDT, 0 WDT postscaler, 1 TO, 0 PD 0 f 255 d [0,1] a [0,1] Operation: (W) - (f) - (C) dest Status Affected: N, OV, C, DC, Z Status Affected: TO, PD Encoding: 0000 Encoding: 0000 0000 0011 Description: The Power-Down Status bit (PD) is cleared. The Time-out Status bit (TO) is set. Watchdog Timer and its postscaler are cleared. The processor is put into Sleep mode with the oscillator stopped. Words: 1 Cycles: 1 0101 Q1 Q2 Q3 Q4 No operation Process Data Go to Sleep Example: SLEEP Before Instruction TO = ? ? PD = After Instruction 1 TO = 0 PD = If WDT causes wake-up, this bit is cleared. DS39636D-page 294 01da ffff ffff Description: Subtract register `f' and Carry flag (borrow) from W (2's complement method). If `d' is `0', the result is stored in W. If `d' is `1', the result is stored in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Decode f {,d {,a}} Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination SUBFWB REG, 1, 0 Example 1: Before Instruction REG = 3 W = 2 C = 1 After Instruction REG = FF W = 2 C = 0 Z = 0 N = 1 ; result is negative SUBFWB REG, 0, 0 Example 2: Before Instruction REG = 2 W = 5 C = 1 After Instruction REG = 2 W = 3 C = 1 Z = 0 N = 0 ; result is positive SUBFWB REG, 1, 0 Example 3: Before Instruction REG = 1 W = 2 C = 0 After Instruction REG = 0 W = 2 C = 1 Z = 1 ; result is zero N = 0 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X SUBLW Subtract W from Literal SUBWF Subtract W from f Syntax: SUBLW k Syntax: SUBWF Operands: 0 k 255 Operands: Operation: k - (W) W Status Affected: N, OV, C, DC, Z 0 f 255 d [0,1] a [0,1] Operation: (f) - (W) dest Status Affected: N, OV, C, DC, Z Encoding: 0000 1000 kkkk kkkk Description W is subtracted from the eight-bit literal `k'. The result is placed in W. Words: 1 Cycles: 1 Encoding: 0101 Q1 Q2 Q3 Q4 Read literal `k' Process Data Write to W Example 1: Before Instruction W = C = After Instruction W = C = Z = N = Example 2: Before Instruction W = C = After Instruction W = C = Z = N = Example 3: Before Instruction W = C = After Instruction W = C = Z = N = SUBLW 02h 1 Cycles: 1 Q Cycle Activity: 02h ? 00h 1 ; result is zero 1 0 SUBLW ffff Words: 01h ? SUBLW ffff Subtract W from register `f' (2's complement method). If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. 02h 01h 1 ; result is positive 0 0 11da Description: Q Cycle Activity: Decode f {,d {,a}} 02h 03h ? FFh ; (2's complement) 0 ; result is negative 0 1 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination SUBWF REG, 1, 0 Example 1: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 2: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 3: Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = (c) 2009 Microchip Technology Inc. 3 2 ? 1 2 1 0 0 SUBWF ; result is positive REG, 0, 0 2 2 ? 2 0 1 1 0 SUBWF ; result is zero REG, 1, 0 1 2 ? FFh ;(2's complement) 2 0 ; result is negative 0 1 DS39636D-page 295 PIC18F2X1X/4X1X SUBWFB Subtract W from f with Borrow SWAPF Swap f Syntax: SUBWFB Syntax: SWAPF f {,d {,a}} Operands: 0 f 255 d [0,1] a [0,1] Operands: 0 f 255 d [0,1] a [0,1] Operation: (f) - (W) - (C) dest Operation: Status Affected: N, OV, C, DC, Z (f<3:0>) dest<7:4>, (f<7:4>) dest<3:0> Status Affected: None Encoding: 0101 Description: f {,d {,a}} 10da ffff ffff Subtract W and the Carry flag (borrow) from register `f' (2's complement method). If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Decode Q2 Read register `f' Example 1: SUBWFB Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 2: Q4 Write to destination (0001 1001) (0000 1101) 0Ch 0Dh 1 0 0 (0000 1011) (0000 1101) 10da ffff ffff The upper and lower nibbles of register `f' are exchanged. If `d' is `0', the result is placed in W. If `d' is `1', the result is placed in register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination REG, 1, 0 19h 0Dh 1 0011 Description: Example: SWAPF Before Instruction REG = After Instruction REG = REG, 1, 0 53h 35h ; result is positive SUBWFB REG, 0, 0 Before Instruction REG = W = C = After Instruction REG = W = C = Z = N = Example 3: 1Bh 1Ah 0 (0001 1011) (0001 1010) 1Bh 00h 1 1 0 (0001 1011) SUBWFB Before Instruction REG = W = C = After Instruction REG = W C Z N Q3 Process Data Encoding: = = = = DS39636D-page 296 ; result is zero REG, 1, 0 03h 0Eh 1 (0000 0011) (0000 1101) F5h (1111 0100) ; [2's comp] (0000 1101) 0Eh 0 0 1 ; result is negative (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TBLRD Table Read TBLRD Table Read (Continued) Syntax: TBLRD ( *; *+; *-; +*) Example 1: TBLRD Operands: None Operation: if TBLRD *, (Prog Mem (TBLPTR)) TABLAT; TBLPTR - No Change; if TBLRD *+, (Prog Mem (TBLPTR)) TABLAT; (TBLPTR) + 1 TBLPTR; if TBLRD *-, (Prog Mem (TBLPTR)) TABLAT; (TBLPTR) - 1 TBLPTR; if TBLRD +*, (TBLPTR) + 1 TBLPTR; (Prog Mem (TBLPTR)) TABLAT; Before Instruction TABLAT TBLPTR MEMORY (00A356h) After Instruction TABLAT TBLPTR Example 2: Status Affected: None Encoding: 0000 0000 0000 *+ ; 10nn nn=0 * =1 *+ =2 *=3 +* Description: This instruction is used to read the contents of Program Memory (P.M.). To address the program memory, a pointer called Table Pointer (TBLPTR) is used. The TBLPTR (a 21-bit pointer) points to each byte in the program memory. TBLPTR has a 2-Mbyte address range. TBLPTR[0] = 0: Least Significant Byte of Program Memory Word TBLPTR[0] = 1: Most Significant Byte of Program Memory Word The TBLRD instruction can modify the value of TBLPTR as follows: * no change * post-increment * post-decrement * pre-increment Words: 1 Cycles: 2 TBLRD = = = 55h 00A356h 34h = = 34h 00A357h +* ; Before Instruction TABLAT TBLPTR MEMORY (01A357h) MEMORY (01A358h) After Instruction TABLAT TBLPTR = = = = AAh 01A357h 12h 34h = = 34h 01A358h Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No operation No operation No operation No operation No operation (Read Program Memory) (c) 2009 Microchip Technology Inc. No No operation operation (Write TABLAT) DS39636D-page 297 PIC18F2X1X/4X1X TBLWT Table Write TBLWT Table Write (Continued) Syntax: TBLWT ( *; *+; *-; +*) Example 1: TBLWT Operands: None Operation: if TBLWT*, (TABLAT) Holding Register; TBLPTR - No Change; if TBLWT*+, (TABLAT) Holding Register; (TBLPTR) + 1 TBLPTR; if TBLWT*-, (TABLAT) Holding Register; (TBLPTR) - 1 TBLPTR; if TBLWT+*, (TBLPTR) + 1 TBLPTR; (TABLAT) Holding Register; Status Affected: Example 2: None Encoding: 0000 0000 0000 *+; Before Instruction TABLAT = 55h TBLPTR = 00A356h HOLDING REGISTER (00A356h) = FFh After Instructions (table write completion) TABLAT = 55h TBLPTR = 00A357h HOLDING REGISTER (00A356h) = 55h 11nn nn=0 * =1 *+ =2 *=3 +* Description: This instruction uses the 3 LSBs of TBLPTR to determine which of the 8 holding registers the TABLAT is written to. The holding registers are used to program the contents of Program Memory (P.M.). (Refer to Section 6.0 "Flash Program Memory" for additional details on programming Flash memory.) The TBLPTR (a 21-bit pointer) points to each byte in the program memory. TBLPTR has a 2-MByte address range. The LSb of the TBLPTR selects which byte of the program memory location to access. TBLPTR[0] = 0: Least Significant Byte of Program Memory Word TBLPTR[0] = 1: Most Significant Byte of Program Memory Word The TBLWT instruction can modify the value of TBLPTR as follows: * no change * post-increment * post-decrement * pre-increment Words: 1 Cycles: 2 TBLWT +*; Before Instruction TABLAT = 34h TBLPTR = 01389Ah HOLDING REGISTER (01389Ah) = FFh HOLDING REGISTER (01389Bh) = FFh After Instruction (table write completion) TABLAT = 34h TBLPTR = 01389Bh HOLDING REGISTER (01389Ah) = FFh HOLDING REGISTER (01389Bh) = 34h Q Cycle Activity: Q1 Decode Q2 Q3 Q4 No No No operation operation operation No No No No operation operation operation operation (Write to (Read Holding TABLAT) Register ) DS39636D-page 298 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TSTFSZ Test f, Skip if 0 XORLW Exclusive OR Literal with W Syntax: TSTFSZ f {,a} Syntax: XORLW k Operands: 0 f 255 a [0,1] Operands: 0 k 255 Operation: (W) .XOR. k W N, Z Operation: skip if f = 0 Status Affected: Status Affected: None Encoding: Encoding: 0110 Description: 011a ffff ffff If `f' = 0, the next instruction fetched during the current instruction execution is discarded and a NOP is executed, making this a two-cycle instruction. If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1(2) Note: 3 cycles if skip and followed by a 2-word instruction. 0000 1010 kkkk kkkk Description: The contents of W are XORed with the 8-bit literal `k'. The result is placed in W. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal `k' Process Data Write to W Example: XORLW 0AFh Before Instruction W = After Instruction W = B5h 1Ah Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data No operation If skip: Q1 Q2 Q3 Q4 No operation No operation No operation No operation If skip and followed by 2-word instruction: Q1 Q2 Q3 Q4 No operation No operation No operation No operation No operation No operation No operation No operation Example: HERE NZERO ZERO Before Instruction PC After Instruction If CNT PC If CNT PC TSTFSZ : : CNT, 1 = Address (HERE) = = = 00h, Address (ZERO) 00h, Address (NZERO) (c) 2009 Microchip Technology Inc. DS39636D-page 299 PIC18F2X1X/4X1X XORWF Exclusive OR W with f Syntax: XORWF Operands: 0 f 255 d [0,1] a [0,1] Operation: (W) .XOR. (f) dest Status Affected: N, Z Encoding: 0001 f {,d {,a}} 10da ffff ffff Description: Exclusive OR the contents of W with register `f'. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in the register `f' (default). If `a' is `0', the Access Bank is selected. If `a' is `1', the BSR is used to select the GPR bank (default). If `a' is `0' and the extended instruction set is enabled, this instruction operates in Indexed Literal Offset Addressing mode whenever f 95 (5Fh). See Section 23.2.3 "Byte-Oriented and Bit-Oriented Instructions in Indexed Literal Offset Mode" for details. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination Example: XORWF Before Instruction REG = W = After Instruction REG = W = DS39636D-page 300 REG, 1, 0 AFh B5h 1Ah B5h (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 23.2 Extended Instruction Set A summary of the instructions in the extended instruction set is provided in Table 23-3. Detailed descriptions are provided in Section 23.2.2 "Extended Instruction Set". The opcode field descriptions in Table 23-1 (page 260) apply to both the standard and extended PIC18 instruction sets. In addition to the standard 75 instructions of the PIC18 instruction set, PIC18F2X1X/4X1X devices also provide an optional extension to the core CPU functionality. The added features include eight additional instructions that augment indirect and indexed addressing operations and the implementation of Indexed Literal Offset Addressing mode for many of the standard PIC18 instructions. Note: The additional features of the extended instruction set are disabled by default. To enable them, users must set the XINST Configuration bit. The instructions in the extended set (with the exception of CALLW, MOVSF and MOVSS) can all be classified as literal operations, which either manipulate the File Select Registers, or use them for indexed addressing. Two of the instructions, ADDFSR and SUBFSR, each have an additional special instantiation for using FSR2. These versions (ADDULNK and SUBULNK) allow for automatic return after execution. 23.2.1 EXTENDED INSTRUCTION SYNTAX Most of the extended instructions use indexed arguments, using one of the File Select Registers and some offset to specify a source or destination register. When an argument for an instruction serves as part of indexed addressing, it is enclosed in square brackets ("[ ]"). This is done to indicate that the argument is used as an index or offset. The MPASMTM Assembler will flag an error if it determines that an index or offset value is not bracketed. The extended instructions are specifically implemented to optimize re-entrant program code (that is, code that is recursive or that uses a software stack) written in high-level languages, particularly C. Among other things, they allow users working in high-level languages to perform certain operations on data structures more efficiently. These include: When the extended instruction set is enabled, brackets are also used to indicate index arguments in byteoriented and bit-oriented instructions. This is in addition to other changes in their syntax. For more details, see Section 23.2.3.1 "Extended Instruction Syntax with Standard PIC18 Commands". * Dynamic allocation and deallocation of software stack space when entering and leaving subroutines * Function Pointer invocation * Software Stack Pointer manipulation * Manipulation of variables located in a software stack TABLE 23-3: The instruction set extension and the Indexed Literal Offset Addressing mode were designed for optimizing applications written in C. The user may likely never use these instructions directly in assembler. The syntax for these commands is provided as a reference for users who may be reviewing code that has been generated by a compiler. Note: In the past, square brackets have been used to denote optional arguments in the PIC18 and earlier instruction sets. In this text and going forward, optional arguments are denoted by braces ("{ }"). EXTENSIONS TO THE PIC18 INSTRUCTION SET Mnemonic, Operands ADDFSR ADDULNK CALLW MOVSF f, k k MOVSS zs, zd PUSHL k SUBFSR SUBULNK f, k k zs, fd Description Add literal to FSR Add literal to FSR2 and return Call subroutine using WREG Move zs (source) to 1st word fd (destination) 2nd word Move zs (source) to 1st word zd (destination) 2nd word Store literal at FSR2, decrement FSR2 Subtract literal from FSR Subtract literal from FSR2 and return (c) 2009 Microchip Technology Inc. Cycles 1 2 2 2 16-Bit Instruction Word MSb LSb Status Affected 1000 1000 0000 1011 ffff 1011 xxxx 1010 ffkk 11kk 0001 0zzz ffff 1zzz xzzz kkkk kkkk kkkk 0100 zzzz ffff zzzz zzzz kkkk None None None None 1 1110 1110 0000 1110 1111 1110 1111 1110 1 2 1110 1110 1001 1001 ffkk 11kk kkkk kkkk None None 2 None None DS39636D-page 301 PIC18F2X1X/4X1X 23.2.2 EXTENDED INSTRUCTION SET ADDFSR Add Literal to FSR ADDULNK Syntax: ADDFSR f, k Syntax: ADDULNK k Operands: 0 k 63 f [ 0, 1, 2 ] Operands: 0 k 63 Operation: FSR(f) + k FSR(f) Status Affected: None Encoding: 1110 Add Literal to FSR2 and Return FSR2 + k FSR2, Operation: (TOS) PC Status Affected: 1000 ffkk kkkk Description: The 6-bit literal `k' is added to the contents of the FSR specified by `f'. Words: 1 Cycles: 1 None Encoding: 1110 Q1 Q2 Q3 Q4 Read literal `k' Process Data Write to FSR Example: ADDFSR Before Instruction FSR2 = 03FFh After Instruction FSR2 = 0422h 2, 23h kkkk Words: 1 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read literal `k' Process Data Write to FSR No Operation No Operation No Operation No Operation Example: Note: 11kk The 6-bit literal `k' is added to the contents of FSR2. A RETURN is then executed by loading the PC with the TOS. The instruction takes two cycles to execute; a NOP is performed during the second cycle. This may be thought of as a special case of the ADDFSR instruction, where f = 3 (binary `11'); it operates only on FSR2. Q Cycle Activity: Decode 1000 Description: ADDULNK 23h Before Instruction FSR2 = PC = 03FFh 0100h After Instruction FSR2 = PC = 0422h (TOS) All PIC18 instructions may take an optional label argument preceding the instruction mnemonic for use in symbolic addressing. If a label is used, the instruction syntax then becomes: {label} instruction argument(s). DS39636D-page 302 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X CALLW Subroutine Call Using WREG MOVSF Syntax: CALLW Syntax: MOVSF [zs], fd Operands: None Operands: Operation: (PC + 2) TOS, (W) PCL, (PCLATH) PCH, (PCLATU) PCU 0 zs 127 0 fd 4095 Operation: ((FSR2) + zs) fd Status Affected: None Status Affected: None Encoding: 0000 0000 0001 0100 Description First, the return address (PC + 2) is pushed onto the return stack. Next, the contents of W are written to PCL; the existing value is discarded. Then the contents of PCLATH and PCLATU are latched into PCH and PCU, respectively. The second cycle is executed as a NOP instruction while the new next instruction is fetched. Unlike CALL, there is no option to update W, STATUS or BSR. Words: 1 Cycles: 2 Move Indexed to f Encoding: 1st word (source) 2nd word (destin.) Q1 Q2 Q3 Q4 Read WREG Push PC to stack No operation No operation No operation No operation No operation HERE Before Instruction PC = PCLATH = PCLATU = W = After Instruction PC = TOS = PCLATH = PCLATU = W = 2 Cycles: 2 Q Cycle Activity: Q1 Decode address (HERE) 10h 00h 06h (c) 2009 Microchip Technology Inc. zzzzs ffffd Words: CALLW 001006h address (HERE + 2) 10h 00h 06h 0zzz ffff The contents of the source register are moved to destination register `fd'. The actual address of the source register is determined by adding the 7-bit literal offset `zs' in the first word to the value of FSR2. The address of the destination register is specified by the 12-bit literal `fd' in the second word. Both addresses can be anywhere in the 4096-byte data space (000h to FFFh). The MOVSF instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. If the resultant source address points to an indirect addressing register, the value returned will be 00h. Decode Example: 1011 ffff Description: Q Cycle Activity: Decode 1110 1111 Q2 Q3 Determine Determine source addr source addr No operation No operation No dummy read Example: MOVSF Before Instruction FSR2 Contents of 85h REG2 After Instruction FSR2 Contents of 85h REG2 Q4 Read source reg Write register `f' (dest) [05h], REG2 = 80h = = 33h 11h = 80h = = 33h 33h DS39636D-page 303 PIC18F2X1X/4X1X MOVSS Move Indexed to Indexed PUSHL Syntax: Syntax: PUSHL k Operands: MOVSS [zs], [zd] 0 zs 127 0 zd 127 Operands: 0 k 255 Operation: ((FSR2) + zs) ((FSR2) + zd) Operation: k (FSR2), FSR2 - 1 FSR2 Status Affected: None Status Affected: None Encoding: 1st word (source) 2nd word (dest.) 1110 1111 Description 1011 xxxx 1zzz xzzz zzzzs zzzzd The contents of the source register are moved to the destination register. The addresses of the source and destination registers are determined by adding the 7-bit literal offsets `zs' or `zd', respectively, to the value of FSR2. Both registers can be located anywhere in the 4096-byte data memory space (000h to FFFh). The MOVSS instruction cannot use the PCL, TOSU, TOSH or TOSL as the destination register. If the resultant source address points to an indirect addressing register, the value returned will be 00h. If the resultant destination address points to an indirect addressing register, the instruction will execute as a NOP. Words: 2 Cycles: 2 Q Cycle Activity: Q1 Decode Decode Q2 Q3 Determine Determine source addr source addr Determine dest addr Example: MOVSS Before Instruction FSR2 Contents of 85h Contents of 86h After Instruction FSR2 Contents of 85h Contents of 86h DS39636D-page 304 Determine dest addr Store Literal at FSR2, Decrement FSR2 Encoding: 1111 1010 kkkk kkkk Description: The 8-bit literal `k' is written to the data memory address specified by FSR2. FSR2 is decremented by 1 after the operation. This instruction allows users to push values onto a software stack. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read `k' Process data Write to destination Example: PUSHL 08h Before Instruction FSR2H:FSR2L Memory (01ECh) = = 01ECh 00h After Instruction FSR2H:FSR2L Memory (01ECh) = = 01EBh 08h Q4 Read source reg Write to dest reg [05h], [06h] = 80h = 33h = 11h = 80h = 33h = 33h (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X SUBFSR Subtract Literal from FSR SUBULNK Syntax: SUBFSR f, k Syntax: SUBULNK k Operands: 0 k 63 Operands: 0 k 63 f [ 0, 1, 2 ] Operation: Operation: FSR(f) - k FSRf Status Affected: None Encoding: 1110 FSR2 - k FSR2 (TOS) PC Status Affected: None 1001 ffkk kkkk Description: The 6-bit literal `k' is subtracted from the contents of the FSR specified by `f'. Words: 1 Cycles: 1 Encoding: 1110 Q1 Q2 Q3 Q4 Decode Read register `f' Process Data Write to destination SUBFSR 2, 23h 1001 11kk kkkk Description: The 6-bit literal `k' is subtracted from the contents of the FSR2. A RETURN is then executed by loading the PC with the TOS. The instruction takes two cycles to execute; a NOP is performed during the second cycle. This may be thought of as a special case of the SUBFSR instruction, where f = 3 (binary `11'); it operates only on FSR2. Words: 1 Cycles: 2 Q Cycle Activity: Example: Subtract Literal from FSR2 and Return Q Cycle Activity: Before Instruction FSR2 = Q1 Q2 Q3 Q4 03FFh Decode After Instruction FSR2 = Read register `f' Process Data Write to destination 03DCh No Operation No Operation No Operation No Operation Example: (c) 2009 Microchip Technology Inc. SUBULNK 23h Before Instruction FSR2 = PC = 03FFh 0100h After Instruction FSR2 = PC = 03DCh (TOS) DS39636D-page 305 PIC18F2X1X/4X1X 23.2.3 Note: BYTE-ORIENTED AND BIT-ORIENTED INSTRUCTIONS IN INDEXED LITERAL OFFSET MODE Enabling the PIC18 instruction set extension may cause legacy applications to behave erratically or fail entirely. In addition to eight new commands in the extended set, enabling the extended instruction set also enables Indexed Literal Offset Addressing mode (Section 5.5.1 "Indexed Addressing with Literal Offset"). This has a significant impact on the way that many commands of the standard PIC18 instruction set are interpreted. When the extended set is disabled, addresses embedded in opcodes are treated as literal memory locations: either as a location in the Access Bank (`a' = 0) or in a GPR bank designated by the BSR (`a' = 1). When the extended instruction set is enabled and `a' = 0, however, a file register argument of 5Fh or less is interpreted as an offset from the pointer value in FSR2 and not as a literal address. For practical purposes, this means that all instructions that use the Access RAM bit as an argument - that is, all byte-oriented and bitoriented instructions, or almost half of the core PIC18 instructions - may behave differently when the extended instruction set is enabled. When the content of FSR2 is 00h, the boundaries of the Access RAM are essentially remapped to their original values. This may be useful in creating backward compatible code. If this technique is used, it may be necessary to save the value of FSR2 and restore it when moving back and forth between C and assembly routines in order to preserve the Stack Pointer. Users must also keep in mind the syntax requirements of the extended instruction set (see Section 23.2.3.1 "Extended Instruction Syntax with Standard PIC18 Commands"). 23.2.3.1 Extended Instruction Syntax with Standard PIC18 Commands When the extended instruction set is enabled, the file register argument, `f', in the standard byte-oriented and bit-oriented commands is replaced with the literal offset value, `k'. As already noted, this occurs only when `f' is less than or equal to 5Fh. When an offset value is used, it must be indicated by square brackets ("[ ]"). As with the extended instructions, the use of brackets indicates to the compiler that the value is to be interpreted as an index or an offset. Omitting the brackets, or using a value greater than 5Fh within brackets, will generate an error in the MPASM Assembler. If the index argument is properly bracketed for Indexed Literal Offset Addressing, the Access RAM argument is never specified; it will automatically be assumed to be `0'. This is in contrast to standard operation (extended instruction set disabled) when `a' is set on the basis of the target address. Declaring the Access RAM bit in this mode will also generate an error in the MPASM Assembler. The destination argument, `d', functions as before. In the latest versions of the MPASM Assembler, language support for the extended instruction set must be explicitly invoked. This is done with either the command line option, /y, or the PE directive in the source listing. 23.2.4 CONSIDERATIONS WHEN ENABLING THE EXTENDED INSTRUCTION SET It is important to note that the extensions to the instruction set may not be beneficial to all users. In particular, users who are not writing code that uses a software stack may not benefit from using the extensions to the instruction set. Although the Indexed Literal Offset Addressing mode can be very useful for dynamic stack and pointer manipulation, it can also be very annoying if a simple arithmetic operation is carried out on the wrong register. Users who are accustomed to the PIC18 programming must keep in mind that when the extended instruction set is enabled, register addresses of 5Fh or less are used for Indexed Literal Offset Addressing. Additionally, the Indexed Literal Offset Addressing mode may create issues with legacy applications written to the PIC18 assembler. This is because instructions in the legacy code may attempt to address registers in the Access Bank below 5Fh. Since these addresses are interpreted as literal offsets to FSR2 when the instruction set extension is enabled, the application may read or write to the wrong data addresses. Representative examples of typical byte-oriented and bit-oriented instructions in the Indexed Literal Offset Addressing mode are provided on the following page to show how execution is affected. The operand conditions shown in the examples are applicable to all instructions of these types. When porting an application to the PIC18F2X1X/4X1X, it is very important to consider the type of code. A large, re-entrant application that is written in `C' and would benefit from efficient compilation will do well when using the instruction set extensions. Legacy applications that heavily use the Access Bank will most likely not benefit from using the extended instruction set. DS39636D-page 306 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X ADDWF Add W to Indexed (Indexed Literal Offset mode) BSF Bit Set Indexed (Indexed Literal Offset mode) Syntax: ADDWF Syntax: BSF [k], b Operands: 0 k 95 d [0,1] Operands: 0 f 95 0b7 Operation: (W) + ((FSR2) + k) dest Operation: 1 ((FSR2) + k)<b> Status Affected: N, OV, C, DC, Z Status Affected: None Encoding: [k] {,d} 0010 Description: 01d0 kkkk kkkk The contents of W are added to the contents of the register indicated by FSR2, offset by the value `k'. If `d' is `0', the result is stored in W. If `d' is `1', the result is stored back in register `f' (default). Encoding: 1000 bbb0 kkkk kkkk Description: Bit `b' of the register indicated by FSR2, offset by the value `k', is set. Words: 1 Cycles: 1 Q Cycle Activity: Words: 1 Q1 Q2 Q3 Q4 Cycles: 1 Decode Read register `f' Process Data Write to destination Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read `k' Process Data Write to destination Example: ADDWF [OFST] ,0 Before Instruction W OFST FSR2 Contents of 0A2Ch After Instruction W Contents of 0A2Ch = = = 17h 2Ch 0A00h = 20h = 37h = 20h Example: BSF Before Instruction FLAG_OFST FSR2 Contents of 0A0Ah After Instruction Contents of 0A0Ah [FLAG_OFST], 7 = = 0Ah 0A00h = 55h = D5h SETF Set Indexed (Indexed Literal Offset mode) Syntax: SETF [k] Operands: 0 k 95 Operation: FFh ((FSR2) + k) Status Affected: None Encoding: 0110 1000 kkkk kkkk Description: The contents of the register indicated by FSR2, offset by `k', are set to FFh. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read `k' Process Data Write register Example: SETF Before Instruction OFST FSR2 Contents of 0A2Ch After Instruction Contents of 0A2Ch (c) 2009 Microchip Technology Inc. [OFST] = = 2Ch 0A00h = 00h = FFh DS39636D-page 307 PIC18F2X1X/4X1X 23.2.5 SPECIAL CONSIDERATIONS WITH MICROCHIP MPLAB(R) IDE TOOLS The latest versions of Microchip's software tools have been designed to fully support the extended instruction set of the PIC18F2X1X/4X1X family of devices. This includes the MPLAB C18 C compiler, MPASM assembly language and MPLAB Integrated Development Environment (IDE). When selecting a target device for software development, MPLAB IDE will automatically set default Configuration bits for that device. The default setting for the XINST Configuration bit is `0', disabling the extended instruction set and Indexed Literal Offset Addressing mode. For proper execution of applications developed to take advantage of the extended instruction set, XINST must be set during programming. DS39636D-page 308 To develop software for the extended instruction set, the user must enable support for the instructions and the Indexed Addressing mode in their language tool(s). Depending on the environment being used, this may be done in several ways: * A menu option, or dialog box within the environment, that allows the user to configure the language tool and its settings for the project * A command line option * A directive in the source code These options vary between different compilers, assemblers and development environments. Users are encouraged to review the documentation accompanying their development systems for the appropriate information. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 24.0 DEVELOPMENT SUPPORT The PIC(R) microcontrollers and dsPIC(R) digital signal controllers are supported with a full range of software and hardware development tools: * Integrated Development Environment - MPLAB(R) IDE Software * Compilers/Assemblers/Linkers - MPLAB C Compiler for Various Device Families - HI-TECH C for Various Device Families - MPASMTM Assembler - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB Assembler/Linker/Librarian for Various Device Families * Simulators - MPLAB SIM Software Simulator * Emulators - MPLAB REAL ICETM In-Circuit Emulator * In-Circuit Debuggers - MPLAB ICD 3 - PICkitTM 3 Debug Express * Device Programmers - PICkitTM 2 Programmer - MPLAB PM3 Device Programmer * Low-Cost Demonstration/Development Boards, Evaluation Kits, and Starter Kits 24.1 MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16/32-bit microcontroller market. The MPLAB IDE is a Windows(R) operating system-based application that contains: * A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - In-Circuit Emulator (sold separately) - In-Circuit Debugger (sold separately) * A full-featured editor with color-coded context * A multiple project manager * Customizable data windows with direct edit of contents * High-level source code debugging * Mouse over variable inspection * Drag and drop variables from source to watch windows * Extensive on-line help * Integration of select third party tools, such as IAR C Compilers The MPLAB IDE allows you to: * Edit your source files (either C or assembly) * One-touch compile or assemble, and download to emulator and simulator tools (automatically updates all project information) * Debug using: - Source files (C or assembly) - Mixed C and assembly - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power. (c) 2009 Microchip Technology Inc. DS39636D-page 309 PIC18F2X1X/4X1X 24.2 MPLAB C Compilers for Various Device Families The MPLAB C Compiler code development systems are complete ANSI C compilers for Microchip's PIC18, PIC24 and PIC32 families of microcontrollers and the dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 24.3 HI-TECH C for Various Device Families The HI-TECH C Compiler code development systems are complete ANSI C compilers for Microchip's PIC family of microcontrollers and the dsPIC family of digital signal controllers. These compilers provide powerful integration capabilities, omniscient code generation and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple platforms. 24.4 MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for PIC10/12/16/18 MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel(R) standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: 24.5 MPLINK Object Linker/ MPLIB Object Librarian The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: * Efficient linking of single libraries instead of many smaller files * Enhanced code maintainability by grouping related modules together * Flexible creation of libraries with easy module listing, replacement, deletion and extraction 24.6 MPLAB Assembler, Linker and Librarian for Various Device Families MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, PIC32 and dsPIC devices. MPLAB C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: * * * * * * Support for the entire device instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility * Integration into MPLAB IDE projects * User-defined macros to streamline assembly code * Conditional assembly for multi-purpose source files * Directives that allow complete control over the assembly process DS39636D-page 310 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 24.7 MPLAB SIM Software Simulator The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC(R) DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C Compilers, and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. 24.8 MPLAB REAL ICE In-Circuit Emulator System MPLAB REAL ICE In-Circuit Emulator System is Microchip's next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC(R) Flash MCUs and dsPIC(R) Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The emulator is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal (LVDS) interconnection (CAT5). The emulator is field upgradable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables. (c) 2009 Microchip Technology Inc. 24.9 MPLAB ICD 3 In-Circuit Debugger System MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost effective high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices. It debugs and programs PIC(R) Flash microcontrollers and dsPIC(R) DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated Development Environment (IDE). The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with a connector compatible with the MPLAB ICD 2 or MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 supports all MPLAB ICD 2 headers. 24.10 PICkit 3 In-Circuit Debugger/ Programmer and PICkit 3 Debug Express The MPLAB PICkit 3 allows debugging and programming of PIC(R) and dsPIC(R) Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial ProgrammingTM. The PICkit 3 Debug Express include the PICkit 3, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software. DS39636D-page 311 PIC18F2X1X/4X1X 24.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express 24.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits The PICkitTM 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip's Flash families of microcontrollers. The full featured Windows(R) programming interface supports baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip's powerful MPLAB Integrated Development Environment (IDE) the PICkitTM 2 enables in-circuit debugging on most PIC(R) microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified. A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. The PICkit 2 Debug Express include the PICkit 2, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software. 24.12 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSPTM cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an MMC card for file storage and data applications. DS39636D-page 312 The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEMTM and dsPICDEMTM demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ(R) security ICs, CAN, IrDA(R), PowerSmart battery management, SEEVAL(R) evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings() Ambient temperature under bias.............................................................................................................-40C to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on any pin with respect to VSS (except VDD and MCLR) ................................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.5V Voltage on MCLR with respect to VSS (Note 2) ......................................................................................... 0V to +13.25V Total power dissipation (Note 1) ...............................................................................................................................1.0W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) .............................................................................................................. 20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by all ports .......................................................................................................................200 mA Maximum current sourced by all ports ..................................................................................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - IOH} + {(VDD - VOH) x IOH} + (VOL x IOL) 2: Voltage spikes below VSS at the MCLR/VPP/RE3 pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a "low" level to the MCLR/VPP/ RE3 pin, rather than pulling this pin directly to VSS. NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. (c) 2009 Microchip Technology Inc. DS39636D-page 313 PIC18F2X1X/4X1X FIGURE 25-1: PIC18F2X1X/4X1X VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) 6.0V 5.5V Voltage 5.0V PIC18F2X1X/4X1X 4.5V 4.2V 4.0V 3.5V 3.0V 2.5V 2.0V 40 MHz Frequency FIGURE 25-2: PIC18F2X1X/4X1X VOLTAGE-FREQUENCY GRAPH (EXTENDED) 6.0V 5.5V Voltage 5.0V PIC18F2X1X/4X1X 4.5V 4.2V 4.0V 3.5V 3.0V 2.5V 2.0V 25 MHz Frequency DS39636D-page 314 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 25-3: PIC18LF2X1X/4X1X VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL) 6.0V 5.5V Voltage 5.0V PIC18LF2X1X/4X1X 4.5V 4.2V 4.0V 3.5V 3.0V 2.5V 2.0V 40 MHz 4 MHz Frequency FMAX = (16.36 MHz/V) (VDDAPPMIN - 2.0V) + 4 MHz Note: VDDAPPMIN is the minimum voltage of the PIC(R) device in the application. (c) 2009 Microchip Technology Inc. DS39636D-page 315 PIC18F2X1X/4X1X 25.1 DC Characteristics: Supply Voltage PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended Param No. D001 Symbol VDD D002 VDR D003 VPOR D004 SVDD VBOR D005 D005 Legend: Note 1: Characteristic Min Typ Max Units Conditions Supply Voltage PIC18LF2X1X/4X1X 2.0 PIC18F2X1X/4X1X 4.2 RAM Data Retention 1.5 Voltage(1) VDD Start Voltage -- to ensure internal Power-on Reset signal VDD Rise Rate 0.05 to ensure internal Power-on Reset signal Brown-out Reset Voltage PIC18LF2X1X/4X1X -- -- -- 5.5 5.5 -- V V V HS, XT, RC and LP Oscillator mode -- 0.7 V See section on Power-on Reset for details -- -- V/ms See section on Power-on Reset for details BORV1:BORV0 = 11 NA 2.05 2.16 V BORV1:BORV0 = 10 2.65 2.79 2.93 V All devices BORV1:BORV0 = 01 4.11 4.33 4.55 V BORV1:BORV0 = 00 4.36 4.59 4.82 V Shading of rows is to assist in readability of the table. This is the limit to which VDD can be lowered in Sleep mode, or during a device Reset, without losing RAM data. DS39636D-page 316 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Power-down Current Typ Max Units Conditions (IPD)(1) PIC18LF2X1X/4X1X Legend: Note 1: 2: 3: 4: 5: 0.1 950 nA -40C VDD = 2.0V, 0.1 1.0 A +25C (Sleep mode) 0.2 5 A +85C PIC18LF2X1X/4X1X 0.1 1.4 A -40C VDD = 3.0V, 0.1 2 A +25C (Sleep mode) 0.3 8 A +85C All devices 0.1 1.9 A -40C 0.1 2.0 A +25C VDD = 5.0V, (Sleep mode) 0.4 15 A +85C Extended devices only 10 120 A +125C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. (c) 2009 Microchip Technology Inc. DS39636D-page 317 PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Supply Current (IDD)(2,3) PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only Legend: Note 1: 2: 3: 4: 5: Typ Max Units Conditions 15 15 15 31.5 30 28.5 A A A -40C +25C +85C 40 35 30 105 90 80 80 0.32 0.33 0.33 0.6 0.55 0.6 1.1 1.1 1.0 1 63 60 57 168 160 152 250 1 1 1 1.3 1.2 1.1 2.3 2.2 2.1 3.3 A A A A A A A mA mA mA mA mA mA mA mA mA mA -40C +25C +85C -40C +25C +85C +125C -40C +25C +85C -40C +25C +85C -40C +25C +85C +125C VDD = 2.0V VDD = 3.0V FOSC = 31 kHz (RC_RUN mode, INTRC source) VDD = 5.0V VDD = 2.0V VDD = 3.0V FOSC = 1 MHz (RC_RUN mode, INTOSC source) VDD = 5.0V Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39636D-page 318 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Supply Current (IDD)(2,3) PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only Legend: Note 1: 2: 3: 4: 5: Typ Max Units Conditions 0.8 0.8 0.8 2.1 2.0 1.9 A A A -40C +25C +85C 1.3 1.3 1.3 2.5 2.5 2.5 2.5 2.9 3.1 3.6 4.5 4.8 5.8 9.2 9.8 11.4 21 3.0 3.0 3.0 5.3 5.0 4.8 10 8 8 11 11 11 15 16 16 36 180 mA mA mA mA mA mA mA A A A A A A A A A A -40C +25C +85C -40C +25C +85C +125C -40C +25C +85C -40C +25C +85C -40C +25C +85C +125C VDD = 2.0V VDD = 3.0V FOSC = 4 MHz (RC_RUN mode, INTOSC source) VDD = 5.0V VDD = 2.0V VDD = 3.0V FOSC = 31 kHz (RC_IDLE mode, INTRC source) VDD = 5.0V Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. (c) 2009 Microchip Technology Inc. DS39636D-page 319 PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Supply Current (IDD)(2,3) PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only Legend: Note 1: 2: 3: 4: 5: Typ Max Units Conditions 165 175 190 350 350 350 A A A -40C +25C +85C 250 270 290 500 520 550 0.6 340 350 360 520 540 580 1.0 1.1 1.1 1.1 500 500 500 1 1 1 2.9 500 500 500 900 900 900 1.6 1.5 1.4 5.0 A A A mA mA mA mA A A A A A A mA mA mA mA -40C +25C +85C -40C +25C +85C +125C -40C +25C +85C -40C +25C +85C -40C +25C +85C +125C VDD = 2.0V VDD = 3.0V FOSC = 1 MHz (RC_IDLE mode, INTOSC source) VDD = 5.0V VDD = 2.0V VDD = 3.0V FOSC = 4 MHz (RC_IDLE mode, INTOSC source) VDD = 5.0V Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39636D-page 320 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Supply Current (IDD)(2,3) PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only Extended devices only Typ Max Units Conditions 250 260 250 500 500 500 A A A -40C +25C +85C 550 480 460 1.2 1.1 1.0 1.0 0.72 0.74 0.74 1.3 1.3 1.3 2.7 2.6 2.5 2.6 8.4 11 650 650 650 1.6 1.5 1.4 3.5 2.0 2.0 2.0 3.0 3.0 3.0 6.0 6.0 6.0 7.0 21 28 A A A mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA -40C +25C +85C -40C +25C +85C +125C -40C +25C +85C -40C +25C +85C -40C +25C +85C +125C +125C +125C VDD = 2.0V VDD = 3.0V FOSC = 1 MHZ (PRI_RUN, EC oscillator) VDD = 5.0V VDD = 2.0V VDD = 3.0V FOSC = 4 MHz (PRI_RUN, EC oscillator) VDD = 5.0V VDD = 4.2V VDD = 5.0V FOSC = 25 MHz (PRI_RUN, EC oscillator) All devices Legend: Note 1: 2: 3: 4: 5: 15 35 mA -40C 16 35 mA +25C VDD = 4.2V FOSC = 40 MHZ 16 35 mA +85C (PRI_RUN, All devices 21 40 mA -40C EC oscillator) VDD = 5.0V 21 40 mA +25C 21 40 mA +85C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. (c) 2009 Microchip Technology Inc. DS39636D-page 321 PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Supply Current (IDD)(2,3) All devices Extended devices only All devices Extended devices only All devices All devices Legend: Note 1: 2: 3: 4: 5: Typ Max Units Conditions 7.5 7.4 7.3 16 15 14 mA mA mA -40C +25C +85C 8.0 10 10 9.7 10 17 17 17 23 23 23 25 21 20 19 35 35 35 35 40 40 40 mA mA mA mA mA mA mA mA mA mA mA +125C -40C +25C +85C +125C -40C +25C +85C -40C +25C +85C VDD = 4.2V FOSC = 4 MHZ (PRI_RUN HS+PLL) VDD = 5.0V FOSC = 4 MHZ (PRI_RUN HS+PLL) VDD = 4.2V FOSC = 10 MHZ (PRI_RUN HS+PLL) VDD = 5.0V FOSC = 10 MHZ (PRI_RUN HS+PLL) Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. DS39636D-page 322 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Typ Max Units Conditions 65 65 130 120 A A -40C +25C 70 120 120 130 300 240 300 320 260 255 270 420 430 450 0.9 0.9 0.9 1 2.8 4.3 115 270 250 240 480 450 430 900 475 450 430 900 850 810 1.5 1.4 1.3 1.2 7.0 11 A A A A A A A A A A A A A A mA mA mA mA mA mA +85C -40C +25C +85C -40C +25C +85C +125C -40C +25C +85C -40C +25C +85C -40C +25C +85C +125C +125C +125C (IDD)(2,3) Supply Current PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only PIC18LF2X1X/4X1X PIC18LF2X1X/4X1X All devices Extended devices only Extended devices only VDD = 2.0V VDD = 3.0V FOSC = 1 MHz (PRI_IDLE mode, EC oscillator) VDD = 5.0V VDD = 2.0V VDD = 3.0V FOSC = 4 MHz (PRI_IDLE mode, EC oscillator) VDD = 5.0V VDD = 4.2V VDD = 5.0V FOSC = 25 MHz (PRI_IDLE mode, EC oscillator) All devices Legend: Note 1: 2: 3: 4: 5: 6.0 16 mA -40C VDD = 4.2V 6.2 16 mA +25C FOSC = 40 MHz 6.6 16 mA +85C (PRI_IDLE mode, All devices 8.1 18 mA -40C EC oscillator) VDD = 5.0V 9.1 18 mA +25C 8.3 18 mA +85C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. (c) 2009 Microchip Technology Inc. DS39636D-page 323 PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. Device Typ Max Units 14 15 16 40 40 40 A A A Conditions (IDD)(2,3) Supply Current PIC18LF2X1X/4X1X -40C +25C +85C VDD = 2.0V 40 74 A -40C FOSC = 32 kHz(4) 35 70 A +25C VDD = 3.0V (SEC_RUN mode, Timer1 as clock) 31 67 A +85C All devices 99 150 A -40C VDD = 5.0V 81 150 A +25C 75 150 A +85C PIC18LF2X1X/4X1X 2.5 12 A -40C 3.7 12 A +25C VDD = 2.0V 4.5 12 A +85C PIC18LF2X1X/4X1X 5.0 15 A -40C FOSC = 32 kHz(4) VDD = 3.0V 5.4 15 A +25C (SEC_IDLE mode, Timer1 as clock) 6.3 15 A +85C All devices 8.5 25 A -40C VDD = 5.0V 9.0 25 A +25C 10.5 36 A +85C Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. PIC18LF2X1X/4X1X Legend: Note 1: 2: 3: 4: 5: DS39636D-page 324 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.2 DC Characteristics: Power-Down and Supply Current PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial -40C TA +125C for extended ParamNo. D022 (IWDT) D022A (IBOR) D022B (ILVD) D025 (IOSCB) D026 (IAD) Device Brown-out Reset(5) High/Low-Voltage Detect(5) Timer1 Oscillator A/D Converter Legend: Note 1: 2: 3: 4: 5: Typ Max Units Conditions Module Differential Currents (IWDT, IBOR, ILVD, IOSCB, IAD) Watchdog Timer 1.3 3.8 A -40C 1.4 3.8 A +25C 2.0 3.8 A +85C VDD = 2.0V 1.9 2.0 2.8 4.0 5.5 5.6 13 35 40 55 0 4.6 4.6 4.6 10 10 10 13 40 45 45 5 A A A A A A A A A A A -40C +25C +85C -40C +25C +85C +125C -40C to +85C -40C to +85C -40C to +125C -40C to +125C 22 25 29 30 2.1 38 40 45 45 4.5 A A A A A -40C to +85C -40C to +85C -40C to +85C -40C to +125C -40C VDD = 2.0V VDD = 3.0V 1.8 2.1 2.2 2.6 2.9 3.0 4.5 4.5 6.0 6.0 6.0 8.0 A A A A A A +25C +85C -40C +25C +85C -40C VDD = 2.0V 32 kHz on Timer1(4) VDD = 3.0V 32 kHz on Timer1(4) 3.2 3.4 1.0 1.0 1.0 2.0 8.0 8.0 2.0 2.0 2.0 8.0 A A A A A A +25C +85C -40C to +85C -40C to +85C -40C to +85C -40C to +125C VDD = 5.0V 32 kHz on Timer1(4) VDD = 3.0V VDD = 5.0V VDD = 3.0V VDD = 5.0V Sleep mode, BOREN1:BOREN0 = 10 VDD = 5.0V VDD = 2.0V VDD = 3.0V A/D on, not converting VDD = 5.0V Shading of rows is to assist in readability of the table. The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.). The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT enabled/disabled as specified. For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in k. Low-power Timer1 oscillator selected. BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less than the sum of both specifications. (c) 2009 Microchip Technology Inc. DS39636D-page 325 PIC18F2X1X/4X1X 25.3 DC Characteristics: PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial DC CHARACTERISTICS Param Symbol No. VIL Characteristic Min Max Units Conditions VSS 0.15 VDD V VDD < 4.5V -- 0.8 V 4.5V VDD 5.5V VSS VSS 0.2 VDD 0.3 VDD V V Input Low Voltage I/O ports: D030 with TTL buffer D030A D031 with Schmitt Trigger buffer RC3 and RC4 D032 MCLR VSS 0.2 VDD V D033 OSC1 VSS 0.3 VDD V HS, HSPLL modes D033A D033B D034 OSC1 OSC1 T13CKI VSS VSS VSS 0.2 VDD 0.3 VDD 0.3 VDD V V V RC, EC modes(1) XT, LP modes 0.25 VDD + 0.8V VDD V VDD < 4.5V 4.5V VDD 5.5V VIH Input High Voltage I/O ports: D040 with TTL buffer D040A D041 with Schmitt Trigger buffer RC3 and RC4 2.0 VDD V 0.8 VDD 0.7 VDD VDD VDD V V D042 MCLR 0.8 VDD VDD V D043 OSC1 0.7 VDD VDD V HS, HSPLL modes D043A D043B D043C D044 OSC1 OSC1 OSC1 T13CKI 0.8 VDD 0.9 VDD 1.6 1.6 VDD VDD VDD VDD V V V V EC mode RC mode(1) XT, LP modes -- 1 A VSS VPIN VDD, Pin at high-impedance IIL D060 Input Leakage Current(2,3) I/O ports D061 MCLR -- 5 A Vss VPIN VDD D063 OSC1 -- 5 A Vss VPIN VDD 50 400 A VDD = 5V, VPIN = VSS D070 Note 1: 2: 3: 4: IPU Weak Pull-up Current IPURB PORTB weak pull-up current In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the PIC(R) device be driven with an external clock while in RC mode. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. Parameter is characterized but not tested. DS39636D-page 326 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.3 DC Characteristics: PIC18F2X1X/4X1X (Industrial) PIC18LF2X1X/4X1X (Industrial) (Continued) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial DC CHARACTERISTICS Param Symbol No. VOL Characteristic Min Max Units Conditions Output Low Voltage D080 I/O ports -- 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40C to +85C D083 OSC2/CLKO (RC, RCIO, EC, ECIO modes) -- 0.6 V IOL = 1.6 mA, VDD = 4.5V, -40C to +85C VOH Output High Voltage(3) D090 I/O ports VDD - 0.7 -- V IOH = -3.0 mA, VDD = 4.5V, -40C to +85C D092 OSC2/CLKO (RC, RCIO, EC, ECIO modes) VDD - 0.7 -- V IOH = -1.3 mA, VDD = 4.5V, -40C to +85C Capacitive Loading Specs on Output Pins D100(4) COSC2 OSC2 pin -- 15 pF In XT, HS and LP modes when external clock is used to drive OSC1 D101 CIO All I/O pins and OSC2 (in RC mode) -- 50 pF To meet the AC Timing Specifications D102 CB SCL, SDA -- 400 pF I2CTM Specification Note 1: 2: 3: 4: In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the PIC(R) device be driven with an external clock while in RC mode. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as current sourced by the pin. Parameter is characterized but not tested. (c) 2009 Microchip Technology Inc. DS39636D-page 327 PIC18F2X1X/4X1X TABLE 25-1: MEMORY PROGRAMMING REQUIREMENTS Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial DC Characteristics Param No. Sym Characteristic Min Typ Max Units Conditions VDD + 4 -- 12.5 V -- 10 -- mA E/W -40C to +85C Internal Program Memory Programming Specifications(1) D110 VPP Voltage on MCLR/VPP/RE3 pin (Note 2) D113 IDDP Supply Current during Programming D130 EP Cell Endurance 10K 100K -- D131 VPR VDD for Read VMIN -- 5.5 V VMIN = Minimum operating voltage D132 VIE VDD for Block Erase 4.5 -- 5.5 V Using ICSPTM port D132A VIW VDD for Externally Timed Erase or Write 4.5 -- 5.5 V Using ICSP port D133 TIE ICSP Block Erase Cycle Time -- 4 -- ms VDD > 4.5V ICSP Erase or Write Cycle Time (externally timed) 1 -- -- ms VDD > 4.5V 40 100 -- Program Flash Memory D133A TIW D134 TRETD Characteristic Retention Year Provided no other specifications are violated Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: These specifications are for programming the on-chip program memory through the use of table write instructions. 2: Required only if Single-Supply programming is disabled. DS39636D-page 328 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 25-2: COMPARATOR SPECIFICATIONS Operating Conditions: 3.0V < VDD < 5.5V, -40C < TA < +85C (unless otherwise stated). Param No. Sym Characteristics Min Typ Max Units Comments D300 VIOFF Input Offset Voltage -- 5.0 10 mV D301 VICM Input Common Mode Voltage* 0 -- VDD - 1.5 V D302 CMRR Common Mode Rejection Ratio* 55 -- -- dB 300 TRESP Response Time(1)* -- 150 400 ns PIC18FXXXX -- 150 600 ns PIC18LFXXXX, VDD = 2.0V -- -- 10 s 300A 301 * Note 1: TMC2OV Comparator Mode Change to Output Valid* These parameters are characterized but not tested. Response time measured with one comparator input at (VDD - 1.5)/2, while the other input transitions from VSS to VDD. TABLE 25-3: VOLTAGE REFERENCE SPECIFICATIONS Operating Conditions: 3.0V < VDD < 5.5V, -40C < TA < +85C (unless otherwise stated). Param No. Sym Characteristics Min Typ Max Units D310 VRES Resolution VDD/24 -- VDD/32 LSb D311 VRAA Absolute Accuracy -- -- 1/2 LSb D312 VRUR Unit Resistor Value (R)* -- 2k -- 310 TSET Settling Time(1)* -- -- 10 s * Note 1: Comments These parameters are characterized but not tested. Settling time measured while CVRR = 1 and CVR3:CVR0 transitions from `0000' to `1111'. (c) 2009 Microchip Technology Inc. DS39636D-page 329 PIC18F2X1X/4X1X FIGURE 25-4: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS VDD (HLVDIF can be cleared in software) VLVD (HLVDIF set by hardware) HLVDIF(1) Note 1: VDIRMAG = 0. TABLE 25-4: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial Param Symbol No. D420 Characteristic Min Typ Max Units HLVD Voltage on VDD LVV = 0000 Transition High to Low LVV = 0001 2.06 2.17 2.28 V 2.12 2.23 2.34 V LVV = 0010 2.24 2.36 2.48 V LVV = 0011 2.32 2.44 2.56 V LVV = 0100 2.47 2.60 2.73 V LVV = 0101 2.65 2.79 2.93 V LVV = 0110 2.74 2.89 3.04 V LVV = 0111 2.96 3.12 3.28 V LVV = 1000 3.22 3.39 3.56 V LVV = 1001 3.37 3.55 3.73 V LVV = 1010 3.52 3.71 3.90 V LVV = 1011 3.70 3.90 4.10 V LVV = 1100 3.90 4.11 4.32 V LVV = 1101 4.11 4.33 4.55 V LVV = 1110 4.36 4.59 4.82 V Conditions Production tested at TAMB = 25C. Specifications over temperature limits ensured by characterization. DS39636D-page 330 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.4 25.4.1 AC (Timing) Characteristics TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created using one of the following formats: 1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKO cs CS di SDI do SDO dt Data in io I/O port mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (High-impedance) L Low I2C only AA output access BUF Bus free TCC:ST (I2C specifications only) CC HD Hold ST DAT DATA input hold STA Start condition (c) 2009 Microchip Technology Inc. 3. TCC:ST 4. Ts (I2C specifications only) (I2C specifications only) T Time osc rd rw sc ss t0 t1 wr OSC1 RD RD or WR SCK SS T0CKI T13CKI WR P R V Z Period Rise Valid High-impedance High Low High Low SU Setup STO Stop condition DS39636D-page 331 PIC18F2X1X/4X1X 25.4.2 TIMING CONDITIONS Note: The temperature and voltages specified in Table 25-5 apply to all timing specifications unless otherwise noted. Figure 25-5 specifies the load conditions for the timing specifications. TABLE 25-5: Because of space limitations, the generic terms "PIC18FXXXX" and "PIC18LFXXXX" are used throughout this section to refer to the PIC18F2X1X/4X1X and PIC18LF2X1X/ 4X1X families of devices specifically and only those devices. TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC AC CHARACTERISTICS FIGURE 25-5: Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial Operating voltage VDD range as described in DC spec Section 25.1 and Section 25.3. LF parts operate for industrial temperatures only. LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 Load Condition 2 VDD/2 RL CL Pin VSS CL Pin RL = 464 VSS DS39636D-page 332 CL = 50 pF for all pins except OSC2/CLKO and including D and E outputs as ports (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 25.4.3 TIMING DIAGRAMS AND SPECIFICATIONS FIGURE 25-6: EXTERNAL CLOCK TIMING (ALL MODES EXCEPT PLL) Q4 Q1 Q2 Q3 Q4 Q1 OSC1 1 3 4 3 4 2 CLKO TABLE 25-6: Param. No. 1A EXTERNAL CLOCK TIMING REQUIREMENTS Symbol FOSC Characteristic Min External CLKI Frequency(1) DC 1 MHz XT, RC Oscillator mode DC 20 MHz HS Oscillator mode DC 31.25 kHz LP Oscillator mode DC 4 MHz RC Oscillator mode 0.1 4 MHz XT Oscillator mode 4 20 MHz HS Oscillator mode 5 200 kHz LP Oscillator mode 1000 -- ns XT, RC Oscillator mode 50 -- ns HS Oscillator mode 32 -- s LP Oscillator mode 250 -- ns RC Oscillator mode 250 1 s XT Oscillator mode 100 250 ns HS Oscillator mode 50 250 ns HS Oscillator mode 5 -- s LP Oscillator mode 100 -- ns TCY = 4/FOSC, Industrial 160 -- ns TCY = 4/FOSC, Extended Oscillator Frequency 1 TOSC (1) External CLKI Period(1) (1) Oscillator Period 2 3 4 Note 1: TCY Instruction Cycle Time(1) TOSL, TOSH External Clock in (OSC1) High or Low Time TOSR, TOSF External Clock in (OSC1) Rise or Fall Time Max Units Conditions 30 -- ns XT Oscillator mode 2.5 -- s LP Oscillator mode 10 -- ns HS Oscillator mode -- 20 ns XT Oscillator mode -- 50 ns LP Oscillator mode -- 7.5 ns HS Oscillator mode Instruction cycle period (TCY) equals four times the input oscillator time base period for all configurations except PLL. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the "max." cycle time limit is "DC" (no clock) for all devices. (c) 2009 Microchip Technology Inc. DS39636D-page 333 PIC18F2X1X/4X1X TABLE 25-7: Param No. PLL CLOCK TIMING SPECIFICATIONS (VDD = 4.2V TO 5.5V) Sym Characteristic Min Typ Max 4 16 -- -- 10 40 Units F10 F11 FOSC Oscillator Frequency Range FSYS On-Chip VCO System Frequency F12 trc PLL Start-up Time (Lock Time) -- -- 2 ms CLK CLKO Stability (Jitter) -2 -- +2 % F13 Conditions MHz HS mode only MHz HS mode only Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. TABLE 25-8: AC CHARACTERISTICS: INTERNAL RC ACCURACY PIC18F2X1X/4X1X (INDUSTRIAL) PIC18LF2X1X/4X1X (INDUSTRIAL) PIC18LF2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial PIC18F2X1X/4X1X (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial Param No. Device Min Typ Max Units Conditions INTOSC Accuracy @ Freq = 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz, 125 kHz, 31 kHz(1) PIC18LF2X1X/4X1X -2 +/-1 2 % -5 -- 5 % -10C to +85C VDD = 2.7-3.3V -10 +/-1 10 % -40C to +85C VDD = 2.7-3.3V -2 +/-1 2 % -5 -- 5 % -10C to +85C VDD = 4.5-5.5V -10 +/-1 10 % -40C to +85C VDD = 4.5-5.5V PIC18LF2X1X/4X1X 26.562 -- 35.938 kHz -40C to +85C VDD = 2.7-3.3V PIC18F2X1X/4X1X 26.562 -- 35.938 kHz -40C to +85C VDD = 4.5-5.5V PIC18F2X1X/4X1X +25C +25C VDD = 2.7-3.3V VDD = 4.5-5.5V INTRC Accuracy @ Freq = 31 kHz(2) Legend: Note 1: 2: 3: Shading of rows is to assist in readability of the table. Frequency calibrated at 25C. OSCTUNE register can be used to compensate for temperature drift. INTRC frequency after calibration. Change of INTRC frequency as VDD changes. DS39636D-page 334 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 25-7: CLKO AND I/O TIMING Q1 Q4 Q2 Q3 OSC1 11 10 CLKO 13 14 19 12 18 16 I/O pin (Input) 15 17 I/O pin (Output) Note: 20, 21 Refer to Figure 25-5 for load conditions. TABLE 25-9: Param No. 10 New Value Old Value CLKO AND I/O TIMING REQUIREMENTS Symbol Characteristic TosH2ckL OSC1 to CLKO Min Typ Max -- 75 200 Units Conditions ns (Note 1) 11 TosH2ckH OSC1 to CLKO -- 75 200 ns (Note 1) 12 TckR CLKO Rise Time -- 35 100 ns (Note 1) 13 TckF CLKO Fall Time -- 35 100 ns (Note 1) 14 TckL2ioV CLKO to Port Out Valid -- -- 0.5 TCY + 20 ns (Note 1) 15 TioV2ckH Port In Valid before CLKO 16 TckH2ioI 17 TosH2ioV OSC1 (Q1 cycle) to Port Out Valid 18 TosH2ioI 18A Port In Hold after CLKO OSC1 (Q2 cycle) to Port Input Invalid (I/O in hold time) 0.25 TCY + 25 -- -- ns (Note 1) 0 -- -- ns (Note 1) -- 50 150 ns PIC18FXXXX 100 -- -- ns PIC18LFXXXX 200 -- -- ns 19 TioV2osH Port Input Valid to OSC1 (I/O in setup time) 0 -- -- ns 20 TioR Port Output Rise Time 20A 21 TioF Port Output Fall Time 21A PIC18FXXXX -- 10 25 ns PIC18LFXXXX -- -- 60 ns PIC18FXXXX -- 10 25 ns PIC18LFXXXX -- -- 60 ns 22 TINP INTx pin High or Low Time TCY -- -- ns 23 TRBP RB7:RB4 Change INTx High or Low Time TCY -- -- ns VDD = 2.0V VDD = 2.0V VDD = 2.0V These parameters are asynchronous events not related to any internal clock edges. Note 1: Measurements are taken in RC mode, where CLKO output is 4 x TOSC. (c) 2009 Microchip Technology Inc. DS39636D-page 335 PIC18F2X1X/4X1X FIGURE 25-8: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal Reset Watchdog Timer Reset 31 34 34 I/O pins Note: Refer to Figure 25-5 for load conditions. FIGURE 25-9: BROWN-OUT RESET TIMING BVDD VDD 35 VIRVST Enable Internal Reference Voltage Internal Reference Voltage Stable 36 TABLE 25-10: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT RESET REQUIREMENTS Param. Symbol No. Characteristic 30 TmcL MCLR Pulse Width (low) 31 TWDT Watchdog Timer Time-out Period (no postscaler) 32 33 TOST TPWRT Oscillation Start-up Timer Period Power-up Timer Period 34 TIOZ 35 TBOR I/O High-Impedance from MCLR Low or Watchdog Timer Reset Brown-out Reset Pulse Width 36 TIVRST 37 TLVD Time for Internal Reference Voltage to become Stable High/Low-Voltage Detect Pulse Width 38 39 TCSD TIOBST CPU Start-up Time Time for INTOSC to Stabilize DS39636D-page 336 Min Typ Max Units 2 -- -- s 3.4 4.0 4.6 ms 1024 TOSC -- 1024 TOSC 55.6 65.5 75 -- ms -- 2 -- s 200 -- -- s -- 20 50 s 200 -- -- s -- -- 10 1 -- -- s s Conditions TOSC = OSC1 period VDD BVDD (see D005) VDD VLVD (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 25-10: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS T0CKI 41 40 42 T1OSO/T13CKI 46 45 47 48 TMR0 or TMR1 Note: Refer to Figure 25-5 for load conditions. TABLE 25-11: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS Param No. Symbol Characteristic 40 Tt0H T0CKI High Pulse Width 41 Tt0L T0CKI Low Pulse Width 42 Tt0P T0CKI Period No prescaler With prescaler No prescaler With prescaler 45 Tt1H 47 0.5 TCY + 20 -- ns 10 -- ns 0.5 TCY + 20 -- ns -- ns -- ns With prescaler Greater of: 20 ns or (TCY + 40)/N -- ns T13CKI Synchronous, no prescaler High Time Synchronous, PIC18FXXXX with prescaler PIC18LFXXXX 0.5 TCY + 20 -- ns 10 -- ns 25 -- ns 30 -- ns PIC18FXXXX T13CKI Low Time Synchronous, no prescaler -- ns -- ns VDD = 2.0V VDD = 2.0V PIC18FXXXX 10 -- ns PIC18LFXXXX 25 -- ns Asynchronous PIC18FXXXX 30 -- ns PIC18LFXXXX 50 -- ns VDD = 2.0V Greater of: 20 ns or (TCY + 40)/N -- ns N = prescale value (1, 2, 4, 8) Tt1P T13CKI Input Period Ft1 T13CKI Oscillator Input Frequency Range Synchronous Tcke2tmrI Delay from External T13CKI Clock Edge to Timer Increment (c) 2009 Microchip Technology Inc. 50 0.5 TCY + 5 N = prescale value (1, 2, 4,..., 256) Synchronous, with prescaler Asynchronous 48 Units Conditions 10 No prescaler PIC18LFXXXX Tt1L Max TCY + 10 Asynchronous 46 Min 60 -- ns DC 50 kHz 2 TOSC 7 TOSC -- VDD = 2.0V DS39636D-page 337 PIC18F2X1X/4X1X FIGURE 25-11: CAPTURE/COMPARE/PWM TIMINGS (ALL CCP MODULES) CCPx (Capture Mode) 50 51 52 CCPx (Compare or PWM Mode) 53 Note: 54 Refer to Figure 25-5 for load conditions. TABLE 25-12: CAPTURE/COMPARE/PWM REQUIREMENTS (ALL CCP MODULES) Param Symbol No. 50 51 TccL TccH Characteristic Min Max Units CCPx Input Low No prescaler Time With PIC18FXXXX prescaler PIC18LFXXXX 0.5 TCY + 20 -- ns 10 -- ns 20 -- ns CCPx Input High Time 0.5 TCY + 20 -- ns No prescaler With prescaler 52 TccP CCPx Input Period 53 TccR CCPx Output Fall Time 54 TccF CCPx Output Fall Time DS39636D-page 338 Conditions VDD = 2.0V PIC18FXXXX 10 -- ns PIC18LFXXXX 20 -- ns VDD = 2.0V 3 TCY + 40 N -- ns N = prescale value (1, 4 or 16) -- 25 ns PIC18FXXXX PIC18LFXXXX -- 45 ns PIC18FXXXX -- 25 ns PIC18LFXXXX -- 45 ns VDD = 2.0V VDD = 2.0V (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 25-12: PARALLEL SLAVE PORT TIMING (PIC18F4410/4415/4510/4515/4610) RE2/CS RE0/RD RE1/WR 65 RD7:RD0 62 64 63 Note: Refer to Figure 25-5 for load conditions. TABLE 25-13: PARALLEL SLAVE PORT REQUIREMENTS (PIC18F4410/4415/4510/4515/4610) Param. No. Symbol Characteristic Min Max Units 62 TdtV2wrH Data In Valid before WR or CS (setup time) 20 -- ns 63 TwrH2dtI WR or CS to Data-In Invalid (hold time) PIC18FXXXX 20 -- ns PIC18LFXXXX 35 -- ns 64 TrdL2dtV RD and CS to Data-Out Valid -- 80 ns 65 TrdH2dtI RD or CS to Data-Out Invalid 10 30 ns 66 TibfINH Inhibit of the IBF Flag bit being Cleared from WR or CS -- 3 TCY (c) 2009 Microchip Technology Inc. Conditions VDD = 2.0V DS39636D-page 339 PIC18F2X1X/4X1X FIGURE 25-13: EXAMPLE SPI MASTER MODE TIMING (CKE = 0) SS 70 SCK (CKP = 0) 71 72 78 79 79 78 SCK (CKP = 1) 80 bit 6 - - - - - -1 MSb SDO LSb 75, 76 SDI MSb In bit 6 - - - -1 LSb In 74 73 Note: Refer to Figure 25-5 for load conditions. TABLE 25-14: EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 0) Param No. Symbol Characteristic Min Max Units 70 TssL2scH, TssL2scL SS to SCK or SCK Input 71 TscH SCK Input High Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns SCK Input Low Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns 100 -- ns 1.5 TCY + 40 -- ns 100 -- ns -- 25 ns 71A 72 TscL 72A TCY 73 TdiV2scH, TdiV2scL Setup Time of SDI Data Input to SCK Edge 73A Tb2b Last Clock Edge of Byte 1 to the 1st Clock Edge of Byte 2 74 TscH2diL, TscL2diL Hold Time of SDI Data Input to SCK Edge 75 TdoR SDO Data Output Rise Time 76 TdoF SDO Data Output Fall Time 78 TscR SCK Output Rise Time (Master mode) PIC18FXXXX PIC18LFXXXX -- ns -- 45 ns -- 25 ns PIC18FXXXX -- 25 ns PIC18LFXXXX -- 45 ns 79 TscF SCK Output Fall Time (Master mode) -- 25 ns 80 TscH2doV, TscL2doV SDO Data Output Valid after SCK Edge PIC18FXXXX -- 50 ns PIC18LFXXXX -- 100 ns Note 1: 2: Conditions (Note 1) (Note 1) (Note 2) VDD = 2.0V VDD = 2.0V VDD = 2.0V Requires the use of Parameter #73A. Only if Parameter #71A and #72A are used. DS39636D-page 340 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 25-14: EXAMPLE SPI MASTER MODE TIMING (CKE = 1) SS 81 SCK (CKP = 0) 71 72 79 73 SCK (CKP = 1) 80 78 MSb SDO bit 6 - - - - - -1 LSb bit 6 - - - -1 LSb In 75, 76 SDI MSb In 74 Note: Refer to Figure 25-5 for load conditions. TABLE 25-15: EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 1) Param. No. 71 Symbol TscH 71A 72 TscL 72A Characteristic Min Max Units SCK Input High Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns SCK Input Low Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns 100 -- ns 1.5 TCY + 40 -- ns 100 -- ns -- 25 ns 45 ns -- 25 ns -- 25 ns 45 ns 73 TdiV2scH, TdiV2scL Setup Time of SDI Data Input to SCK Edge 73A Tb2b Last Clock Edge of Byte 1 to the 1st Clock Edge of Byte 2 74 TscH2diL, TscL2diL Hold Time of SDI Data Input to SCK Edge 75 TdoR SDO Data Output Rise Time 76 TdoF SDO Data Output Fall Time 78 TscR SCK Output Rise Time (Master mode) PIC18FXXXX PIC18LFXXXX PIC18FXXXX PIC18LFXXXX 79 TscF SCK Output Fall Time (Master mode) -- 25 ns 80 TscH2doV, TscL2doV SDO Data Output Valid after SCK Edge -- 50 ns 100 ns 81 TdoV2scH, TdoV2scL SDO Data Output Setup to SCK Edge -- ns Note 1: 2: PIC18FXXXX PIC18LFXXXX TCY Conditions (Note 1) (Note 1) (Note 2) VDD = 2.0V VDD = 2.0V VDD = 2.0V Requires the use of Parameter #73A. Only if Parameter #71A and #72A are used. (c) 2009 Microchip Technology Inc. DS39636D-page 341 PIC18F2X1X/4X1X FIGURE 25-15: EXAMPLE SPI SLAVE MODE TIMING (CKE = 0) SS 70 SCK (CKP = 0) 83 71 72 78 79 79 78 SCK (CKP = 1) 80 MSb SDO bit 6 - - - - - -1 LSb 77 75, 76 MSb In SDI 73 Note: bit 6 - - - -1 LSb In 74 Refer to Figure 25-5 for load conditions. TABLE 25-16: EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING, CKE = 0) Param No. Symbol Characteristic 70 TssL2scH, SS to SCK or SCK Input TssL2scL 71 TscH 71A 72 TscL 72A Min Max Units Conditions TCY -- SCK Input High Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns SCK Input Low Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns 100 -- ns 73 TdiV2scH, Setup Time of SDI Data Input to SCK Edge TdiV2scL 73A Tb2b 74 TscH2diL, Hold Time of SDI Data Input to SCK Edge TscL2diL 75 TdoR Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40 SDO Data Output Rise Time PIC18FXXXX -- ns 100 -- ns -- 25 ns 45 ns PIC18LFXXXX 76 TdoF 77 TssH2doZ SS to SDO Output High-Impedance 78 TscR SDO Data Output Fall Time SCK Output Rise Time (Master mode) PIC18FXXXX -- 25 ns 10 50 ns -- 25 ns 45 ns -- 25 ns -- 50 ns 100 ns -- ns PIC18LFXXXX 79 TscF 80 TscH2doV, SDO Data Output Valid after SCK Edge PIC18FXXXX TscL2doV PIC18LFXXXX 83 Note 1: 2: ns SCK Output Fall Time (Master mode) TscH2ssH, SS after SCK edge TscL2ssH 1.5 TCY + 40 (Note 1) (Note 1) (Note 2) VDD = 2.0V VDD = 2.0V VDD = 2.0V Requires the use of Parameter #73A. Only if Parameter #71A and #72A are used. DS39636D-page 342 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X FIGURE 25-16: EXAMPLE SPI SLAVE MODE TIMING (CKE = 1) 82 SS SCK (CKP = 0) 70 83 71 72 SCK (CKP = 1) 80 MSb SDO bit 6 - - - - - -1 LSb 75, 76 SDI MSb In Note: 77 bit 6 - - - -1 LSb In 74 Refer to Figure 25-5 for load conditions. TABLE 25-17: EXAMPLE SPI SLAVE MODE REQUIREMENTS (CKE = 1) Param No. Symbol Characteristic 70 TssL2scH, SS to SCK or SCK Input TssL2scL 71 TscH 71A 72 TscL 72A Min Max Units Conditions TCY -- ns SCK Input High Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns SCK Input Low Time (Slave mode) Continuous 1.25 TCY + 30 -- ns Single Byte 40 -- ns (Note 1) (Note 2) Last Clock Edge of Byte 1 to the First Clock Edge of Byte 2 1.5 TCY + 40 73A Tb2b 74 TscH2diL, Hold Time of SDI Data Input to SCK Edge TscL2diL 75 TdoR SDO Data Output Rise Time PIC18FXXXX -- ns 100 -- ns -- 25 ns 45 ns -- 25 ns 10 50 ns PIC18LFXXXX 76 TdoF 77 TssH2doZ SS to SDO Output High-Impedance SDO Data Output Fall Time 78 TscR SCK Output Rise Time (Master mode) PIC18FXXXX -- 25 ns PIC18LFXXXX -- 45 ns 79 TscF -- 25 ns 80 TscH2doV, SDO Data Output Valid after SCK TscL2doV Edge PIC18FXXXX -- 50 ns PIC18LFXXXX -- 100 ns TssL2doV SDO Data Output Valid after SS Edge PIC18FXXXX -- 50 ns PIC18LFXXXX -- 100 ns 1.5 TCY + 40 -- ns 82 83 SCK Output Fall Time (Master mode) TscH2ssH, SS after SCK Edge TscL2ssH Note 1: 2: (Note 1) VDD = 2.0V VDD = 2.0V VDD = 2.0V VDD = 2.0V Requires the use of Parameter #73A. Only if Parameter #71A and #72A are used. (c) 2009 Microchip Technology Inc. DS39636D-page 343 PIC18F2X1X/4X1X I2CTM BUS START/STOP BITS TIMING FIGURE 25-17: SCL 91 93 90 92 SDA Stop Condition Start Condition Note: Refer to Figure 25-5 for load conditions. TABLE 25-18: I2CTM BUS START/STOP BITS REQUIREMENTS (SLAVE MODE) Param. Symbol No. 90 91 92 93 TSU:STA THD:STA TSU:STO Characteristic Max Units Conditions ns Only relevant for Repeated Start condition ns After this period, the first clock pulse is generated Start Condition 100 kHz mode 4700 -- Setup Time 400 kHz mode 600 -- Start Condition 100 kHz mode 4000 -- Hold Time 400 kHz mode 600 -- Stop Condition 100 kHz mode 4700 -- Setup Time 400 kHz mode 600 -- 100 kHz mode 4000 -- 400 kHz mode 600 -- THD:STO Stop Condition Hold Time FIGURE 25-18: Min ns ns I2CTM BUS DATA TIMING 103 102 100 101 SCL 90 106 107 91 92 SDA In 110 109 109 SDA Out Note: Refer to Figure 25-5 for load conditions. DS39636D-page 344 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 25-19: I2CTM BUS DATA REQUIREMENTS (SLAVE MODE) Param. Symbol No. 100 THIGH Characteristic Clock High Time 100 kHz mode 400 kHz mode TLOW Clock Low Time 91 106 107 92 109 110 2: s -- -- 100 kHz mode 4.7 -- s 400 kHz mode 1.3 -- s -- ns 20 + 0.1 CB 300 ns 100 kHz mode -- 300 ns 400 kHz mode 20 + 0.1 CB 300 ns CB is specified to be from 10 to 400 pF TSU:STA Start Condition Setup Time 100 kHz mode 4.7 -- s 400 kHz mode 0.6 -- s Only relevant for Repeated Start condition THD:STA Start Condition Hold Time 100 kHz mode 4.0 -- s 400 kHz mode 0.6 -- s THD:DAT Data Input Hold Time 100 kHz mode 0 -- ns 400 kHz mode 0 0.9 s TSU:DAT Data Input Setup Time 100 kHz mode 250 -- ns 400 kHz mode 100 -- ns TSU:STO Stop Condition Setup Time 100 kHz mode 4.7 -- s 400 kHz mode 0.6 -- s TAA 100 kHz mode -- 3500 ns 400 kHz mode -- -- ns CB Note 1: s 1000 TBUF D102 -- -- TF 90 4.0 Conditions 1.5 TCY TR 103 Units 0.6 SSP module 102 Max 1.5 TCY SSP module 101 Min SDA and SCL Rise 100 kHz mode Time 400 kHz mode SDA and SCL Fall Time Output Valid from Clock Bus Free Time 100 kHz mode 4.7 -- s 400 kHz mode 1.3 -- s -- 400 pF Bus Capacitive Loading CB is specified to be from 10 to 400 pF After this period, the first clock pulse is generated (Note 2) (Note 1) Time the bus must be free before a new transmission can start As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement TSU:DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line, TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification), before the SCL line is released. (c) 2009 Microchip Technology Inc. DS39636D-page 345 PIC18F2X1X/4X1X MASTER SSP I2CTM BUS START/STOP BITS TIMING WAVEFORMS FIGURE 25-19: SCL 93 91 90 92 SDA Stop Condition Start Condition Note: Refer to Figure 25-5 for load conditions. TABLE 25-20: MASTER SSP I2CTM BUS START/STOP BITS REQUIREMENTS Param. Symbol No. 90 91 TSU:STA Characteristic ns Only relevant for Repeated Start condition ns After this period, the first clock pulse is generated 100 kHz mode 2(TOSC)(BRG + 1) -- 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode(1) 2(TOSC)(BRG + 1) -- 100 kHz mode 2(TOSC)(BRG + 1) -- 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode(1) 2(TOSC)(BRG + 1) -- 100 kHz mode 2(TOSC)(BRG + 1) -- 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode(1) 2(TOSC)(BRG + 1) -- 100 kHz mode 2(TOSC)(BRG + 1) -- 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode(1) 2(TOSC)(BRG + 1) -- THD:STA Start Condition TSU:STO Stop Condition THD:STO Stop Condition Hold Time Note 1: Maximum pin capacitance = 10 pF for all FIGURE 25-20: Units Setup Time Setup Time 93 Max Start Condition Hold Time 92 Min I2C Conditions ns ns pins. MASTER SSP I2CTM BUS DATA TIMING 103 102 100 101 SCL 90 106 91 107 92 SDA In 109 109 110 SDA Out Note: DS39636D-page 346 Refer to Figure 25-5 for load conditions. (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 25-21: MASTER SSP I2CTM BUS DATA REQUIREMENTS Param. Symbol No. 100 101 THIGH TLOW Characteristic Min Max Units Clock High Time 100 kHz mode 2(TOSC)(BRG + 1) -- ms 400 kHz mode 2(TOSC)(BRG + 1) -- ms 1 MHz mode(1) 2(TOSC)(BRG + 1) -- ms Clock Low Time 100 kHz mode 2(TOSC)(BRG + 1) -- ms 400 kHz mode 2(TOSC)(BRG + 1) -- ms (1) 2(TOSC)(BRG + 1) -- ms 100 kHz mode -- 1000 ns 400 kHz mode 20 + 0.1 CB 300 ns 1 MHz mode(1) -- 300 ns 1 MHz mode 102 103 90 91 TR TF TSU:STA SDA and SCL Rise Time SDA and SCL Fall Time Start Condition Setup Time THD:STA Start Condition Hold Time 100 kHz mode -- 300 ns 400 kHz mode 20 + 0.1 CB 300 ns 1 MHz mode(1) -- 100 ns 100 kHz mode 2(TOSC)(BRG + 1) -- ms 400 kHz mode 2(TOSC)(BRG + 1) -- ms 1 MHz mode(1) 2(TOSC)(BRG + 1) -- ms 100 kHz mode 2(TOSC)(BRG + 1) -- ms 400 kHz mode 2(TOSC)(BRG + 1) -- ms 1 MHz mode(1) 2(TOSC)(BRG + 1) -- ms 0 -- ns 106 THD:DAT Data Input Hold Time 100 kHz mode 400 kHz mode 0 0.9 ms 107 TSU:DAT 100 kHz mode 250 -- ns 92 TSU:STO Stop Condition Setup Time 109 110 D102 Note 1: 2: TAA TBUF CB Data Input Setup Time Output Valid from Clock Bus Free Time 400 kHz mode 100 -- ns 100 kHz mode 2(TOSC)(BRG + 1) -- ms 400 kHz mode 2(TOSC)(BRG + 1) -- ms 1 MHz mode(1) 2(TOSC)(BRG + 1) -- ms 100 kHz mode -- 3500 ns 400 kHz mode -- 1000 ns (1) 1 MHz mode -- -- ns 100 kHz mode 4.7 -- ms 400 kHz mode 1.3 -- ms -- 400 pF Bus Capacitive Loading Conditions CB is specified to be from 10 to 400 pF CB is specified to be from 10 to 400 pF Only relevant for Repeated Start condition After this period, the first clock pulse is generated (Note 2) Time the bus must be free before a new transmission can start 2C Maximum pin capacitance = 10 pF for all I pins. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but parameter 107 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line, parameter 102 + parameter 107 = 1000 + 250 = 1250 ns (for 100 kHz mode), before the SCL line is released. (c) 2009 Microchip Technology Inc. DS39636D-page 347 PIC18F2X1X/4X1X FIGURE 25-21: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING RC6/TX/CK pin 121 121 RC7/RX/DT pin 120 Note: 122 Refer to Figure 25-5 for load conditions. TABLE 25-22: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS Param No. 120 Symbol Characteristic TckH2dtV SYNC XMIT (MASTER & SLAVE) Clock High to Data Out Valid PIC18FXXXX Min Max Units -- 40 ns PIC18LFXXXX -- 100 ns 121 Tckrf Clock Out Rise Time and Fall Time (Master mode) PIC18FXXXX -- 20 ns PIC18LFXXXX -- 50 ns 122 Tdtrf Data Out Rise Time and Fall Time PIC18FXXXX -- 20 ns PIC18LFXXXX -- 50 ns FIGURE 25-22: RC6/TX/CK pin Conditions VDD = 2.0V VDD = 2.0V VDD = 2.0V USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING 125 RC7/RX/DT pin 126 Note: Refer to Figure 25-5 for load conditions. TABLE 25-23: USART SYNCHRONOUS RECEIVE REQUIREMENTS Param. No. 125 126 Symbol TdtV2ckl TckL2dtl DS39636D-page 348 Characteristic Min Max Units SYNC RCV (MASTER & SLAVE) Data Hold before CK (DT hold time) 10 -- ns Data Hold after CK (DT hold time) 15 -- ns Conditions (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X TABLE 25-24: A/D CONVERTER CHARACTERISTICS: PIC18F2X1X/4X1X (INDUSTRIAL) PIC18LF2X1X/4X1X (INDUSTRIAL) Param Symbol No. Characteristic Min Typ Max Units -- -- 10 bit Conditions VREF 3.0V A01 NR Resolution A03 EIL Integral Linearity Error -- -- <1 LSb VREF 3.0V A04 EDL Differential Linearity Error -- -- <1 LSb VREF 3.0V A06 EOFF Offset Error -- -- <1 LSb VREF 3.0V A07 EGN Gain Error -- -- <1 LSb VREF 3.0V A10 -- Monotonicity -- VSS VAIN VREF A20 VREF Reference Voltage Range (VREFH - VREFL) 1.8 3 -- -- -- -- V V VDD < 3.0V VDD 3.0V A21 VREFH Reference Voltage High VSS -- VREFH V A22 VREFL Reference Voltage Low VSS - 0.3V -- VDD - 3.0V V A25 VAIN Analog Input Voltage VREFL -- VREFH V A30 ZAIN Recommended Impedance of Analog Voltage Source -- -- 2.5 k A50 IREF VREF Input Current(2) -- -- -- -- 5 150 A A Note 1: 2: Guaranteed(1) During VAIN acquisition. During A/D conversion cycle. The A/D conversion result never decreases with an increase in the input voltage and has no missing codes. VREFH current is from RA3/AN3/VREF+ pin or VDD, whichever is selected as the VREFH source. VREFL current is from RA2/AN2/VREF-/CVREF pin or VSS, whichever is selected as the VREFL source. (c) 2009 Microchip Technology Inc. DS39636D-page 349 PIC18F2X1X/4X1X FIGURE 25-23: A/D CONVERSION TIMING BSF ADCON0, GO (Note 2) 131 Q4 130 (1) 132 A/D CLK 9 A/D DATA 8 7 ... ... 2 1 0 NEW_DATA OLD_DATA ADRES TCY ADIF GO DONE SAMPLING STOPPED SAMPLE Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 2: This is a minimal RC delay (typically 100 ns), which also disconnects the holding capacitor from the analog input. TABLE 25-25: A/D CONVERSION REQUIREMENTS Param Symbol No. 130 TAD Characteristic A/D Clock Period Min Max Units PIC18FXXXX 0.7 25.0(1) s TOSC based, VREF 3.0V PIC18LFXXXX 1.4 25.0(1) s VDD = 2.0V; TOSC based, VREF full range PIC18FXXXX TBD 1 s A/D RC mode PIC18LFXXXX TBD 3 s VDD = 2.0V; A/D RC mode 11 12 TAD 1.4 TBD -- -- s s 131 TCNV Conversion Time (not including acquisition time) (Note 2) 132 TACQ Acquisition Time (Note 3) 135 TSWC Switching Time from Convert Sample -- (Note 4) TBD TDIS Discharge Time 0.2 -- Legend: Note 1: 2: 3: 4: Conditions -40C to +85C 0C to +85C s TBD = To Be Determined The time of the A/D clock period is dependent on the device frequency and the TAD clock divider. ADRES register may be read on the following TCY cycle. The time for the holding capacitor to acquire the "New" input voltage when the voltage changes full scale after the conversion (VDD to VSS or VSS to VDD). The source impedance (RS) on the input channels is 50. On the following cycle of the device clock. DS39636D-page 350 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 26.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES Graphs and tables are not available at this time. (c) 2009 Microchip Technology Inc. DS39636D-page 351 PIC18F2X1X/4X1X NOTES: DS39636D-page 352 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 27.0 PACKAGING INFORMATION 27.1 Package Marking Information 28-Lead SPDIP Example PIC18F2610-I/SP e3 0710017 XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN 28-Lead SOIC Example XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX YYWWNNN Example 28-Lead QFN 18F2510 -I/ML e3 0710017 XXXXXXXX XXXXXXXX YYWWNNN Legend: XX...X Y YY WW NNN e3 * Note: PIC18F2610-E/SO e3 0710017 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2009 Microchip Technology Inc. DS39636D-page 353 PIC18F2X1X/4X1X 27.1 Package Marking Information (Continued) 40-Lead PDIP Example XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX YYWWNNN 44-Lead QFN XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN 44-Lead TQFP XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN DS39636D-page 354 PIC18F4610-I/P e3 0710017 Example PIC18F4610 -I/ML e3 0710017 Example PIC18F4610 -I/PT e3 0710017 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 27.2 Package Details The following sections give the technical details of the packages. 28-Lead Skinny Plastic Dual In-Line (SP) - 300 mil Body [SPDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE 1 E1 1 2 3 D E A2 A L c b1 A1 b e eB Units Dimension Limits Number of Pins INCHES MIN N NOM MAX 28 Pitch e Top to Seating Plane A - - .200 Molded Package Thickness A2 .120 .135 .150 Base to Seating Plane A1 .015 - - Shoulder to Shoulder Width E .290 .310 .335 Molded Package Width E1 .240 .285 .295 Overall Length D 1.345 1.365 1.400 Tip to Seating Plane L .110 .130 .150 Lead Thickness c .008 .010 .015 b1 .040 .050 .070 b .014 .018 .022 eB - - Upper Lead Width Lower Lead Width Overall Row Spacing .100 BSC .430 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-070B (c) 2009 Microchip Technology Inc. DS39636D-page 355 PIC18F2X1X/4X1X 28-Lead Plastic Small Outline (SO) - Wide, 7.50 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N E E1 NOTE 1 1 2 3 e b h A2 A h c L A1 Units Dimension Limits Number of Pins L1 MILLMETERS MIN N NOM MAX 28 Pitch e Overall Height A - 1.27 BSC - Molded Package Thickness A2 2.05 - - Standoff A1 0.10 - 0.30 Overall Width E Molded Package Width E1 7.50 BSC Overall Length D 17.90 BSC 2.65 10.30 BSC Chamfer (optional) h 0.25 - 0.75 Foot Length L 0.40 - 1.27 Footprint L1 1.40 REF Foot Angle Top 0 - 8 Lead Thickness c 0.18 - 0.33 Lead Width b 0.31 - 0.51 Mold Draft Angle Top 5 - 15 Mold Draft Angle Bottom 5 - 15 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-052B DS39636D-page 356 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 28-Lead Plastic Quad Flat, No Lead Package (ML) - 6x6 mm Body [QFN] with 0.55 mm Contact Length Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D D2 EXPOSED PAD e E b E2 2 2 1 1 N K N NOTE 1 L BOTTOM VIEW TOP VIEW A A3 A1 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 28 Pitch e Overall Height A 0.80 0.65 BSC 0.90 1.00 Standoff A1 0.00 0.02 0.05 Contact Thickness A3 0.20 REF Overall Width E Exposed Pad Width E2 Overall Length D Exposed Pad Length D2 3.65 3.70 4.20 b 0.23 0.30 0.35 Contact Length L 0.50 0.55 0.70 Contact-to-Exposed Pad K 0.20 - - Contact Width 6.00 BSC 3.65 3.70 4.20 6.00 BSC Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package is saw singulated. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-105B (c) 2009 Microchip Technology Inc. DS39636D-page 357 PIC18F2X1X/4X1X 40-Lead Plastic Dual In-Line (P) - 600 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE 1 E1 1 2 3 D E A2 A L c b1 A1 b e eB Units Dimension Limits Number of Pins INCHES MIN N NOM MAX 40 Pitch e Top to Seating Plane A - - .250 Molded Package Thickness A2 .125 - .195 Base to Seating Plane A1 .015 - - Shoulder to Shoulder Width E .590 - .625 Molded Package Width E1 .485 - .580 Overall Length D 1.980 - 2.095 Tip to Seating Plane L .115 - .200 Lead Thickness c .008 - .015 b1 .030 - .070 b .014 - .023 eB - - Upper Lead Width Lower Lead Width Overall Row Spacing .100 BSC .700 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-016B DS39636D-page 358 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X 44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D D2 EXPOSED PAD e E E2 b 2 2 1 N 1 N NOTE 1 TOP VIEW K L BOTTOM VIEW A A3 A1 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 44 Pitch e Overall Height A 0.80 0.65 BSC 0.90 1.00 Standoff A1 0.00 0.02 0.05 Contact Thickness A3 0.20 REF Overall Width E Exposed Pad Width E2 Overall Length D Exposed Pad Length D2 6.30 6.45 6.80 b 0.25 0.30 0.38 Contact Length L 0.30 0.40 0.50 Contact-to-Exposed Pad K 0.20 - - Contact Width 8.00 BSC 6.30 6.45 6.80 8.00 BSC Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package is saw singulated. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-103B (c) 2009 Microchip Technology Inc. DS39636D-page 359 PIC18F2X1X/4X1X 44-Lead Plastic Thin Quad Flatpack (PT) - 10x10x1 mm Body, 2.00 mm Footprint [TQFP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D D1 E e E1 N b NOTE 1 1 2 3 NOTE 2 A c A2 A1 L L1 Units Dimension Limits Number of Leads MILLIMETERS MIN N NOM MAX 44 Lead Pitch e Overall Height A - 0.80 BSC - Molded Package Thickness A2 0.95 1.00 1.05 Standoff A1 0.05 - 0.15 Foot Length L 0.45 0.60 0.75 Footprint L1 1.20 1.00 REF Foot Angle Overall Width E 12.00 BSC Overall Length D 12.00 BSC Molded Package Width E1 10.00 BSC Molded Package Length D1 10.00 BSC 0 3.5 7 Lead Thickness c 0.09 - 0.20 Lead Width b 0.30 0.37 0.45 Mold Draft Angle Top 11 12 13 Mold Draft Angle Bottom 11 12 13 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Chamfers at corners are optional; size may vary. 3. Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.25 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-076B DS39636D-page 360 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X APPENDIX A: REVISION HISTORY Revision A (June 2004) Original data sheet for PIC18F2X1X/4X1X devices. APPENDIX B: DEVICE DIFFERENCES The differences between the devices listed in this data sheet are shown in Table B-1 and Table B-2. Revision B (October 2006) Changes to Register 22-13: Device ID Register 2 and packaging diagrams updated. Revision C (January 2007) Packaging diagrams updated. Revision D (October 2009) Updated to remove Preliminary status. TABLE B-1: DEVICE DIFFERENCES (PIC18F2410/2415/2510/2515/2610) Features PIC18F2410 PIC18F2510 PIC18F2515 PIC18F2610 Program Memory (Bytes) 16384 32768 49152 65536 Program Memory (Instructions) 8192 16384 24576 32768 18 18 18 18 Ports A, B, C, (E) Ports A, B, C, (E) Ports A, B, C, (E) Ports A, B, C, (E) Capture/Compare/PWM Modules 2 2 2 2 Enhanced Capture/Compare/PWM Modules 0 0 0 0 No No No No 10 input channels 10 input channels 10 input channels 10 input channels 28-pin SPDIP 28-pin SOIC 28-pin QFN 28-pin SPDIP 28-pin SOIC 28-pin QFN 28-pin SPDIP 28-pin SOIC 28-pin SPDIP 28-pin SOIC Interrupt Sources I/O Ports Parallel Communications (PSP) 10-bit Analog-to-Digital Module Packages TABLE B-2: DEVICE DIFFERENCES (PIC18F4410/4415/4510/4515/4610) Features PIC18F4410 PIC18F4510 PIC18F4515 PIC18F4610 Program Memory (Bytes) 16384 32768 49152 65536 Program Memory (Instructions) 8192 16384 24576 32768 Interrupt Sources 19 19 19 19 Ports A, B, C, D, E Ports A, B, C, D, E Ports A, B, C, D, E Ports A, B, C, D, E Capture/Compare/PWM Modules 2 2 2 2 Enhanced Capture/Compare/PWM Modules 0 0 0 0 Yes Yes Yes Yes 13 input channels 13 input channels 13 input channels 13 input channels 40-pin PDIP 44-pin QFN 44-pin TQFP 40-pin PDIP 44-pin QFN 44-pin TQFP 40-pin PDIP 44-pin QFN 44-pin TQFP 40-pin PDIP 44-pin QFN 44-pin TQFP I/O Ports Parallel Communications (PSP) 10-bit Analog-to-Digital Module Packages (c) 2009 Microchip Technology Inc. DS39636D-page 361 PIC18F2X1X/4X1X APPENDIX C: CONVERSION CONSIDERATIONS This appendix discusses the considerations for converting from previous versions of a device to the ones listed in this data sheet. Typically, these changes are due to the differences in the process technology used. An example of this type of conversion is from a PIC16C74A to a PIC16C74B. Not Applicable DS39636D-page 362 APPENDIX D: MIGRATION FROM BASELINE TO ENHANCED DEVICES This section discusses how to migrate from a Baseline device (i.e., PIC16C5X) to an Enhanced MCU device (i.e., PIC18FXXX). The following are the list of modifications over the PIC16C5X microcontroller family: Not Currently Available (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X APPENDIX E: MIGRATION FROM MID-RANGE TO ENHANCED DEVICES A detailed discussion of the differences between the mid-range MCU devices (i.e., PIC16CXXX) and the enhanced devices (i.e., PIC18FXXX) is provided in AN716, "Migrating Designs from PIC16C74A/74B to PIC18C442." The changes discussed, while device specific, are generally applicable to all mid-range to enhanced device migrations. APPENDIX F: MIGRATION FROM HIGH-END TO ENHANCED DEVICES A detailed discussion of the migration pathway and differences between the high-end MCU devices (i.e., PIC17CXXX) and the enhanced devices (i.e., PIC18FXXX) is provided in AN726, "PIC17CXXX to PIC18CXXX Migration." This Application Note is available as Literature Number DS00726. This Application Note is available as Literature Number DS00716. (c) 2009 Microchip Technology Inc. DS39636D-page 363 PIC18F2X1X/4X1X NOTES: DS39636D-page 364 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X INDEX A A/D ................................................................................... 213 A/D Converter Interrupt, Configuring ....................... 217 Acquisition Requirements ........................................ 218 ADCON0 Register .................................................... 213 ADCON1 Register .................................................... 213 ADCON2 Register .................................................... 213 ADRESH Register ............................................ 213, 216 ADRESL Register .................................................... 213 Analog Port Pins, Configuring .................................. 220 Associated Registers ............................................... 222 Calculating the Minimum Required Acquisition Time ..... 218 Configuring the Module ............................................ 217 Conversion Clock (TAD) ........................................... 219 Conversion Status (GO/DONE Bit) .......................... 216 Conversions ............................................................. 221 Converter Characteristics ........................................ 349 Operation in Power Managed Modes ...................... 220 Selecting and Configuring Acquisition Time ............ 219 Special Event Trigger (CCP) .................................... 222 Special Event Trigger (ECCP) ................................. 140 Use of the CCP2 Trigger .......................................... 222 Absolute Maximum Ratings ............................................. 313 AC (Timing) Characteristics ............................................. 331 Load Conditions for Device Timing Specifications ... 332 Parameter Symbology ............................................. 331 Temperature and Voltage Specifications ................. 332 Timing Conditions .................................................... 332 AC Characteristics Internal RC Accuracy ............................................... 334 Access Bank Mapping with Indexed Literal Offset Addressing Mode .. 75 ACKSTAT ........................................................................ 183 ACKSTAT Status Flag ..................................................... 183 ADCON0 Register ............................................................ 213 GO/DONE Bit ........................................................... 216 ADCON1 Register ............................................................ 213 ADCON2 Register ............................................................ 213 ADDFSR .......................................................................... 302 ADDLW ............................................................................ 265 ADDULNK ........................................................................ 302 ADDWF ............................................................................ 265 ADDWFC ......................................................................... 266 ADRESH Register ............................................................ 213 ADRESL Register .................................................... 213, 216 Analog-to-Digital Converter. See A/D. ANDLW ............................................................................ 266 ANDWF ............................................................................ 267 Assembler MPASM Assembler .................................................. 310 Auto-Wake-up on Sync Break Character ......................... 206 B Bank Select Register (BSR) ............................................... 61 Baud Rate Generator ....................................................... 179 BC .................................................................................... 267 BCF .................................................................................. 268 BF .................................................................................... 183 BF Status Flag ................................................................. 183 (c) 2009 Microchip Technology Inc. Block Diagrams A/D ........................................................................... 216 Analog Input Model .................................................. 217 Baud Rate Generator .............................................. 179 Capture Mode Operation ......................................... 133 Comparator Analog Input Model .............................. 227 Comparator I/O Operating Modes (Diagram) .......... 224 Comparator Output .................................................. 226 Comparator Voltage Reference ............................... 230 Comparator Voltage Reference Output Buffer Example 231 Compare Mode Operation ....................................... 134 Device Clock .............................................................. 30 Enhanced PWM ....................................................... 141 EUSART Receive .................................................... 204 EUSART Transmit ................................................... 202 External Power-on Reset Circuit (Slow VDD Power-up) 45 Fail-Safe Clock Monitor ........................................... 251 Generic I/O Port ......................................................... 97 High/Low-Voltage Detect with External Input .......... 234 Interrupt Logic ............................................................ 84 MSSP (I2C Master Mode) ........................................ 177 MSSP (I2C Mode) .................................................... 162 MSSP (SPI Mode) ................................................... 153 On-Chip Reset Circuit ................................................ 43 PIC18F2410/2510/2515/2610 ................................... 13 PIC18F4410/4510/4515/4610 ................................... 14 PLL (HS Mode) .......................................................... 27 PORTD and PORTE (Parallel Slave Port) ............... 112 PWM Operation (Simplified) .................................... 136 Reads from Flash Program Memory ......................... 78 Single Comparator ................................................... 225 Table Read Operation ............................................... 77 Timer0 in 16-Bit Mode ............................................. 116 Timer0 in 8-Bit Mode ............................................... 116 Timer1 ..................................................................... 120 Timer1 (16-Bit Read/Write Mode) ............................ 120 Timer2 ..................................................................... 126 Timer3 ..................................................................... 128 Timer3 (16-Bit Read/Write Mode) ............................ 128 Watchdog Timer ...................................................... 248 BN .................................................................................... 268 BNC ................................................................................. 269 BNN ................................................................................. 269 BNOV .............................................................................. 270 BNZ ................................................................................. 270 BOR. See Brown-out Reset. BOV ................................................................................. 273 BRA ................................................................................. 271 Break Character (12-Bit) Transmit and Receive .............. 207 BRG. See Baud Rate Generator. Brown-out Reset (BOR) ..................................................... 46 Detecting ................................................................... 46 Disabling in Sleep Mode ............................................ 46 Software Enabled ...................................................... 46 BSF .................................................................................. 271 BTFSC ............................................................................. 272 BTFSS ............................................................................. 272 BTG ................................................................................. 273 BZ .................................................................................... 274 DS39636D-page 365 PIC18F2X1X/4X1X C C Compilers MPLAB C18 ............................................................. 310 CALL ................................................................................ 274 CALLW ............................................................................. 303 Capture (CCP Module) ..................................................... 133 Associated Registers ............................................... 135 CCP Pin Configuration ............................................. 133 CCPRxH:CCPRxL Registers ................................... 133 Prescaler .................................................................. 133 Software Interrupt .................................................... 133 Timer1/Timer3 Mode Selection ................................ 133 Capture (ECCP Module) .................................................. 140 Capture/Compare/PWM (CCP) ........................................ 131 Capture Mode. See Capture. CCP Mode and Timer Resources ............................ 132 CCPRxH Register .................................................... 132 CCPRxL Register ..................................................... 132 Compare Mode. See Compare. Interaction of Two CCP Modules ............................. 132 Module Configuration ............................................... 132 Clock Sources .................................................................... 30 Selecting the 31 kHz Source ...................................... 31 Selection Using OSCCON Register ........................... 31 CLRF ................................................................................ 275 CLRWDT .......................................................................... 275 Code Examples 16 x 16 Signed Multiply Routine ................................ 82 16 x 16 Unsigned Multiply Routine ............................ 82 8 x 8 Signed Multiply Routine .................................... 81 8 x 8 Unsigned Multiply Routine ................................ 81 Changing Between Capture Prescalers ................... 133 Computed GOTO Using an Offset Value ................... 58 Fast Register Stack .................................................... 58 How to Clear RAM (Bank 1) Using Indirect Addressing . 71 Implementing a Real-Time Clock Using a Timer1 Interrupt Service ...................................................... 123 Initializing PORTA ...................................................... 97 Initializing PORTB .................................................... 100 Initializing PORTC .................................................... 103 Initializing PORTD .................................................... 106 Initializing PORTE .................................................... 109 Loading the SSPBUF (SSPSR) Register ................. 156 Reading a Flash Program Memory Word .................. 79 Saving Status, WREG and BSR Registers in RAM ... 95 Code Protection ............................................................... 239 COMF ............................................................................... 276 Comparator ...................................................................... 223 Analog Input Connection Considerations ................. 227 Associated Registers ............................................... 227 Configuration ............................................................ 224 Effects of a Reset ..................................................... 226 Interrupts .................................................................. 226 Operation ................................................................. 225 Operation During Sleep ........................................... 226 Outputs .................................................................... 225 Reference ................................................................ 225 External Signal ................................................. 225 Internal Signal .................................................. 225 Response Time ........................................................ 225 Comparator Specifications ............................................... 329 Comparator Voltage Reference ....................................... 229 Accuracy and Error .................................................. 230 Associated Registers ............................................... 231 DS39636D-page 366 Configuring .............................................................. 229 Connection Considerations ...................................... 230 Effects of a Reset .................................................... 230 Operation During Sleep ........................................... 230 Compare (CCP Module) .................................................. 134 Associated Registers ............................................... 135 CCPRx Register ...................................................... 134 Pin Configuration ..................................................... 134 Software Interrupt .................................................... 134 Special Event Trigger .............................. 129, 134, 222 Timer1/Timer3 Mode Selection ................................ 134 Compare (ECCP Module) ................................................ 140 Special Event Trigger .............................................. 140 Computed GOTO ............................................................... 58 Configuration Bits ............................................................ 239 Configuration Register Protection .................................... 257 Context Saving During Interrupts ....................................... 95 Conversion Considerations .............................................. 362 CPFSEQ .......................................................................... 276 CPFSGT .......................................................................... 277 CPFSLT ........................................................................... 277 Crystal Oscillator/Ceramic Resonator ................................ 25 Customer Change Notification Service ............................ 375 Customer Notification Service ......................................... 375 Customer Support ............................................................ 375 D Data Addressing Modes .................................................... 71 Comparing Addressing Modes with the Extended Instruction Set Enabled ........................................ 74 Direct ......................................................................... 71 Indexed Literal Offset ................................................ 73 Indirect ....................................................................... 71 Inherent and Literal .................................................... 71 Data Memory ..................................................................... 61 Access Bank .............................................................. 65 and the Extended Instruction Set .............................. 73 Bank Select Register (BSR) ...................................... 61 General Purpose Registers ....................................... 65 Map for PIC18F2410/4410 ........................................ 62 Map for PIC18F2510/4510 ........................................ 63 Map for PIC18F2515/2610/4515/4610 ...................... 64 Special Function Registers ........................................ 66 DAW ................................................................................ 278 DC and AC Characteristics Graphs and Tables .................................................. 351 DC Characteristics ........................................................... 326 Power-Down and Supply Current ............................ 317 Supply Voltage ........................................................ 316 DCFSNZ .......................................................................... 279 DECF ............................................................................... 278 DECFSZ .......................................................................... 279 Development Support ...................................................... 309 Device Differences ........................................................... 361 Device Overview .................................................................. 9 Details on Individual Family Members ....................... 10 New Core Features ...................................................... 9 Other Special Features .............................................. 10 Device Overview (PIC18F2410/2510/2515/2610) Features (table) ......................................................... 11 Device Overview (PIC18F4410/4510/4515/4610) Features (table) ......................................................... 12 Device Reset Timers ......................................................... 47 Oscillator Start-up Timer (OST) ................................. 47 PLL Lock Time-out ..................................................... 47 Power-up Timer (PWRT) ........................................... 47 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X Direct Addressing ............................................................... 72 F E Fail-Safe Clock Monitor ........................................... 239, 251 Interrupts in Power Managed Modes ....................... 252 POR or Wake from Sleep ........................................ 252 WDT During Oscillator Failure ................................. 251 Fast Register Stack ........................................................... 58 Flash Program Memory ..................................................... 77 Associated Registers ................................................. 79 Control Registers ....................................................... 78 Reading ..................................................................... 78 TABLAT (Table Latch) Register ................................ 78 Table Reads and Table Writes .................................. 77 TBLPTR (Table Pointer) Register .............................. 78 FSCM. See Fail-Safe Clock Monitor. Effect on Standard PIC Instructions ........................... 73, 306 Effects of Power Managed Modes on Various Clock Sources 33 Electrical Characteristics .................................................. 313 Enhanced Capture/Compare/PWM (ECCP) .................... 139 Capture and Compare Modes .................................. 140 Capture Mode. See Capture (ECCP Module). Outputs and Configuration ....................................... 140 Pin Configurations for ECCP1 ................................. 140 PWM Mode. See PWM (ECCP Module). Standard PWM Mode ............................................... 140 Timer Resources ...................................................... 140 Enhanced PWM Mode. See PWM (ECCP Module). ........ 141 Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART). See EUSART. Equations A/D Acquisition Time ................................................ 218 A/D Minimum Charging Time ................................... 218 Errata ................................................................................... 8 EUSART Asynchronous Mode ................................................ 202 12-Bit Break Transmit and Receive ................. 207 Associated Registers, Receive ........................ 205 Associated Registers, Transmit ....................... 203 Auto-Wake-up on Sync Break ......................... 206 Receiver ........................................................... 204 Setting up 9-bit Mode with Address Detect ...... 204 Transmitter ....................................................... 202 Baud Rate Generator Operation in Power Managed Mode ................ 197 Baud Rate Generator (BRG) .................................... 197 Associated Registers ....................................... 197 Auto-Baud Rate Detect .................................... 200 Baud Rate Error, Calculating ........................... 197 Baud Rates, Asynchronous Modes ................. 198 High Baud Rate Select (BRGH Bit) ................. 197 Sampling .......................................................... 197 Synchronous Master Mode ...................................... 208 Associated Registers, Receive ........................ 210 Associated Registers, Transmit ....................... 209 Reception ......................................................... 210 Transmission ................................................... 208 Synchronous Slave Mode ........................................ 211 Associated Registers, Receive ........................ 212 Associated Registers, Transmit ....................... 211 Reception ......................................................... 212 Transmission ................................................... 211 Extended Instruction Set .................................................. 301 ADDFSR .................................................................. 302 ADDULNK ................................................................ 302 and Using MPLAB Tools .......................................... 308 CALLW ..................................................................... 303 Considerations for Use ............................................ 306 MOVSF .................................................................... 303 MOVSS .................................................................... 304 PUSHL ..................................................................... 304 SUBFSR .................................................................. 305 SUBULNK ................................................................ 305 Syntax ...................................................................... 301 External Clock Input ........................................................... 26 (c) 2009 Microchip Technology Inc. G General Call Address Support ......................................... 176 GOTO .............................................................................. 280 H Hardware Multiplier ............................................................ 81 Introduction ................................................................ 81 Operation ................................................................... 81 Performance Comparison .......................................... 81 High/Low-Voltage Detect ................................................. 233 Applications ............................................................. 236 Associated Registers ............................................... 237 Characteristics ......................................................... 330 Current Consumption .............................................. 235 Effects of a Reset .................................................... 237 Operation ................................................................. 234 During Sleep .................................................... 237 Setup ....................................................................... 235 Start-up Time ........................................................... 235 Typical Application ................................................... 236 HLVD. See High/Low-Voltage Detect. ............................. 233 I I/O Ports ............................................................................ 97 I2C Mode (MSSP) Acknowledge Sequence Timing .............................. 186 Baud Rate Generator .............................................. 179 Bus Collision During a Repeated Start Condition .................. 190 During a Stop Condition .................................. 191 Clock Arbitration ...................................................... 180 Clock Stretching ...................................................... 172 10-Bit Slave Receive Mode (SEN = 1) ............ 172 10-Bit Slave Transmit Mode ............................ 172 7-Bit Slave Receive Mode (SEN = 1) .............. 172 7-Bit Slave Transmit Mode .............................. 172 Clock Synchronization and the CKP bit (SEN = 1) .. 173 Effects of a Reset .................................................... 187 General Call Address Support ................................. 176 I2C Clock Rate w/BRG ............................................ 179 Master Mode ............................................................ 177 Operation ......................................................... 178 Reception ........................................................ 183 Repeated Start Timing ..................................... 182 Start Condition Timing ..................................... 181 Transmission ................................................... 183 Multi-Master Communication, Bus Collision and Arbitration ........................................................ 187 Multi-Master Mode ................................................... 187 Operation ................................................................. 166 DS39636D-page 367 PIC18F2X1X/4X1X Read/Write Bit Information (R/W Bit) ............... 166, 167 Registers .................................................................. 162 Serial Clock (RC3/SCK/SCL) ................................... 167 Slave Mode .............................................................. 166 Addressing ....................................................... 166 Reception ......................................................... 167 Transmission .................................................... 167 Sleep Operation ....................................................... 187 Stop Condition Timing .............................................. 186 ID Locations ............................................................. 239, 257 INCF ................................................................................. 280 INCFSZ ............................................................................ 281 In-Circuit Debugger .......................................................... 257 In-Circuit Serial Programming (ICSP) ...................... 239, 257 Indexed Literal Offset Addressing and Standard PIC18 Instructions ............................. 306 Indexed Literal Offset Mode ....................................... 73, 306 Indirect Addressing ............................................................ 72 INFSNZ ............................................................................ 281 Initialization Conditions for all Registers ...................... 51-54 Instruction Cycle ................................................................. 59 Clocking Scheme ....................................................... 59 Instruction Flow/Pipelining ................................................. 59 Instruction Set ADDLW .................................................................... 265 ADDWF .................................................................... 265 ADDWF (Indexed Literal Offset mode) .................... 307 ADDWFC ................................................................. 266 ANDLW .................................................................... 266 ANDWF .................................................................... 267 BC ............................................................................ 267 BCF .......................................................................... 268 BN ............................................................................ 268 BNC ......................................................................... 269 BNN ......................................................................... 269 BNOV ....................................................................... 270 BNZ .......................................................................... 270 BOV ......................................................................... 273 BRA .......................................................................... 271 BSF .......................................................................... 271 BSF (Indexed Literal Offset mode) .......................... 307 BTFSC ..................................................................... 272 BTFSS ..................................................................... 272 BTG .......................................................................... 273 BZ ............................................................................ 274 CALL ........................................................................ 274 CLRF ........................................................................ 275 CLRWDT .................................................................. 275 COMF ...................................................................... 276 CPFSEQ .................................................................. 276 CPFSGT .................................................................. 277 CPFSLT ................................................................... 277 DAW ......................................................................... 278 DCFSNZ .................................................................. 279 DECF ....................................................................... 278 DECFSZ ................................................................... 279 Firmware Instructions ............................................... 259 General Format ........................................................ 261 GOTO ...................................................................... 280 INCF ......................................................................... 280 INCFSZ .................................................................... 281 INFSNZ .................................................................... 281 IORLW ..................................................................... 282 IORWF ..................................................................... 282 LFSR ........................................................................ 283 DS39636D-page 368 MOVF ...................................................................... 283 MOVFF .................................................................... 284 MOVLB .................................................................... 284 MOVLW ................................................................... 285 MOVWF ................................................................... 285 MULLW .................................................................... 286 MULWF .................................................................... 286 NEGF ....................................................................... 287 NOP ......................................................................... 287 Opcode Field Descriptions ....................................... 260 POP ......................................................................... 288 PUSH ....................................................................... 288 RCALL ..................................................................... 289 RESET ..................................................................... 289 RETFIE .................................................................... 290 RETLW .................................................................... 290 RETURN .................................................................. 291 RLCF ....................................................................... 291 RLNCF ..................................................................... 292 RRCF ....................................................................... 292 RRNCF .................................................................... 293 SETF ....................................................................... 293 SETF (Indexed Literal Offset mode) ........................ 307 SLEEP ..................................................................... 294 Standard Instructions ............................................... 259 SUBFWB ................................................................. 294 SUBLW .................................................................... 295 SUBWF .................................................................... 295 SUBWFB ................................................................. 296 SWAPF .................................................................... 296 TBLRD ..................................................................... 297 TBLWT .................................................................... 298 TSTFSZ ................................................................... 299 XORLW ................................................................... 299 XORWF ................................................................... 300 INTCON Registers ....................................................... 85-87 Inter-Integrated Circuit. See I2C. Internal Oscillator Block ..................................................... 28 Adjustment ................................................................. 28 INTIO Modes ............................................................. 28 INTOSC Frequency Drift ............................................ 28 INTOSC Output Frequency ....................................... 28 OSCTUNE Register ................................................... 28 PLL in INTOSC Modes .............................................. 28 Internal RC Oscillator Use with WDT .......................................................... 248 Internet Address .............................................................. 375 Interrupt Sources ............................................................. 239 A/D Conversion Complete ....................................... 217 Capture Complete (CCP) ......................................... 133 Compare Complete (CCP) ....................................... 134 Interrupt-on-Change (RB7:RB4) .............................. 100 INTn Pin ..................................................................... 95 PORTB, Interrupt-on-Change .................................... 95 TMR0 ......................................................................... 95 TMR0 Overflow ........................................................ 117 TMR1 Overflow ........................................................ 119 TMR2 to PR2 Match (PWM) ............................ 136, 141 TMR3 Overflow ................................................ 127, 129 Interrupts ............................................................................ 83 Interrupts, Flag Bits Interrupt-on-Change (RB7:RB4) Flag (RBIF Bit) ..... 100 INTOSC, INTRC. See Internal Oscillator Block. IORLW ............................................................................. 282 IORWF ............................................................................. 282 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X IPR Registers ..................................................................... 92 L LFSR ................................................................................ 283 Low-Voltage ICSP Programming. See Single-Supply ICSP Programming M Master Clear (MCLR) ......................................................... 45 Master Synchronous Serial Port (MSSP). See MSSP. Memory Organization ......................................................... 55 Data Memory ............................................................. 61 Program Memory ....................................................... 55 Memory Programming Requirements .............................. 328 Microchip Internet Web Site ............................................. 375 Migration from Baseline to Enhanced Devices ................ 362 Migration from High-End to Enhanced Devices ............... 363 Migration from Mid-Range to Enhanced Devices ............ 363 MOVF ............................................................................... 283 MOVFF ............................................................................ 284 MOVLB ............................................................................ 284 MOVLW ........................................................................... 285 MOVSF ............................................................................ 303 MOVSS ............................................................................ 304 MOVWF ........................................................................... 285 MPLAB ASM30 Assembler, Linker, Librarian .................. 310 MPLAB Integrated Development Environment Software . 309 MPLAB PM3 Device Programmer ................................... 312 MPLAB REAL ICE In-Circuit Emulator System ................ 311 MPLINK Object Linker/MPLIB Object Librarian ............... 310 MSSP ACK Pulse ........................................................ 166, 167 Control Registers (general) ...................................... 153 I2C Mode. See I2C Mode. Module Overview ..................................................... 153 SPI Master/Slave Connection .................................. 157 SPI Mode. See SPI Mode. SSPBUF ................................................................... 158 SSPSR ..................................................................... 158 MULLW ............................................................................ 286 MULWF ............................................................................ 286 N NEGF ............................................................................... 287 NOP ................................................................................. 287 O OPTION_REG Register PSA Bit ..................................................................... 117 T0CS Bit ................................................................... 116 T0PS2:T0PS0 Bits ................................................... 117 T0SE Bit ................................................................... 116 Oscillator Configuration ...................................................... 25 EC .............................................................................. 25 ECIO .......................................................................... 25 HS .............................................................................. 25 HSPLL ........................................................................ 25 Internal Oscillator Block ............................................. 28 INTIO1 ....................................................................... 25 INTIO2 ....................................................................... 25 LP ............................................................................... 25 RC .............................................................................. 25 RCIO .......................................................................... 25 XT .............................................................................. 25 Oscillator Selection .......................................................... 239 Oscillator Start-up Timer (OST) ................................... 33, 47 (c) 2009 Microchip Technology Inc. Oscillator Switching ........................................................... 30 Oscillator Transitions ......................................................... 31 Oscillator, Timer1 ..................................................... 119, 129 Oscillator, Timer3 ............................................................. 127 P Packaging Information ..................................................... 353 Details (Diagrams) ................................................... 355 Marking .................................................................... 353 Parallel Slave Port (PSP) ......................................... 106, 112 Associated Registers ............................................... 113 CS (Chip Select) ...................................................... 112 PORTD .................................................................... 112 RD (Read Input) ...................................................... 112 Select (PSPMODE Bit) .................................... 106, 112 WR (Write Input) ...................................................... 112 PIE Registers ..................................................................... 90 Pin Functions MCLR/VPP/RE3 ................................................... 15, 19 OSC1/CLKI/RA7 .................................................. 15, 19 OSC2/CLKO/RA6 ................................................ 15, 19 RA0/AN0 .............................................................. 16, 20 RA1/AN1 .............................................................. 16, 20 RA2/AN2/VREF-/CVREF ....................................... 16, 20 RA3/AN3/VREF+ .................................................. 16, 20 RA4/T0CKI/C1OUT ............................................. 16, 20 RA5/AN4/SS/HLVDIN/C2OUT ............................ 16, 20 RB0/INT0/FLT0/AN12 ......................................... 17, 21 RB1/INT1/AN10 ................................................... 17, 21 RB2/INT2/AN8 ..................................................... 17, 21 RB3/AN9/CCP2 ................................................... 17, 21 RB4/KBI0/AN11 ................................................... 17, 21 RB5/KBI1/PGM .................................................... 17, 21 RB6/KBI2/PGC .................................................... 17, 21 RB7/KBI3/PGD .................................................... 17, 21 RC0/T1OSO/T13CKI ........................................... 18, 22 RC1/T1OSI/CCP2 ............................................... 18, 22 RC2/CCP1 ................................................................. 18 RC2/CCP1/P1A ......................................................... 22 RC3/SCK/SCL ..................................................... 18, 22 RC4/SDI/SDA ...................................................... 18, 22 RC5/SDO ............................................................. 18, 22 RC6/TX/CK .......................................................... 18, 22 RC7/RX/DT .......................................................... 18, 22 RD0/PSP0 ................................................................. 23 RD1/PSP1 ................................................................. 23 RD2/PSP2 ................................................................. 23 RD3/PSP3 ................................................................. 23 RD4/PSP4 ................................................................. 23 RD5/PSP5/P1B ......................................................... 23 RD6/PSP6/P1C ......................................................... 23 RD7/PSP7/P1D ......................................................... 23 RE0/RD/AN5 ............................................................. 24 RE1/WR/AN6 ............................................................. 24 RE2/CS/AN7 .............................................................. 24 VDD ...................................................................... 18, 24 VSS ...................................................................... 18, 24 Pinout I/O Descriptions PIC18F2410/2510/2515/2610 ................................... 15 PIC18F4410/4510/4515/4610 ................................... 19 PIR Registers ..................................................................... 88 PLL Frequency Multiplier ................................................... 27 HSPLL Oscillator Mode ............................................. 27 Use with INTOSC ...................................................... 27 POP ................................................................................. 288 POR. See Power-on Reset. DS39636D-page 369 PIC18F2X1X/4X1X PORTA Associated Registers ................................................. 99 LATA Register ............................................................ 97 PORTA Register ........................................................ 97 TRISA Register .......................................................... 97 PORTB Associated Registers ............................................... 102 LATB Register .......................................................... 100 PORTB Register ...................................................... 100 RB7:RB4 Interrupt-on-Change Flag (RBIF Bit) ........ 100 TRISB Register ........................................................ 100 PORTC Associated Registers ............................................... 105 LATC Register ......................................................... 103 PORTC Register ...................................................... 103 RC3/SCK/SCL Pin ................................................... 167 TRISC Register ........................................................ 103 PORTD Associated Registers ............................................... 108 LATD Register ......................................................... 106 Parallel Slave Port (PSP) Function .......................... 106 PORTD Register ...................................................... 106 TRISD Register ........................................................ 106 PORTE Associated Registers ............................................... 111 LATE Register .......................................................... 109 PORTE Register ...................................................... 109 PSP Mode Select (PSPMODE Bit) .......................... 106 TRISE Register ........................................................ 109 Postscaler, WDT Assignment (PSA Bit) .............................................. 117 Rate Select (T0PS2:T0PS0 Bits) ............................. 117 Switching Between Timer0 and WDT ...................... 117 Power Managed Modes ..................................................... 35 and A/D Operation ................................................... 220 and EUSART Operation ........................................... 197 and Multiple Sleep Commands .................................. 36 and PWM Operation ................................................ 151 and SPI Operation ................................................... 161 Clock Sources ............................................................ 35 Clock Transitions and Status Indicators ..................... 36 Effects on Clock Sources ........................................... 33 Entering ...................................................................... 35 Exiting Idle and Sleep Modes .................................... 41 by Interrupt ......................................................... 41 by Reset ............................................................. 41 by WDT Time-out ............................................... 41 Without a Start-up Delay .................................... 42 Idle Modes ................................................................. 39 PRI_IDLE ........................................................... 40 RC_IDLE ............................................................ 41 SEC_IDLE .......................................................... 40 Run Modes ................................................................. 36 PRI_RUN ........................................................... 36 RC_RUN ............................................................ 37 SEC_RUN .......................................................... 36 Selecting .................................................................... 35 Sleep Mode ................................................................ 39 Summary (table) ........................................................ 35 Power-on Reset (POR) ...................................................... 45 Power-up Timer (PWRT) ........................................... 47 Time-out Sequence .................................................... 47 Power-up Delays ................................................................ 33 Power-up Timer (PWRT) .................................................... 33 Prescaler DS39636D-page 370 Timer2 ..................................................................... 142 Prescaler, Timer0 ............................................................ 117 Assignment (PSA Bit) .............................................. 117 Rate Select (T0PS2:T0PS0 Bits) ............................. 117 Switching Between Timer0 and WDT ...................... 117 Prescaler, Timer2 ............................................................ 137 PRI_IDLE Mode ................................................................. 40 PRI_RUN Mode ................................................................. 36 Program Counter ............................................................... 56 PCL, PCH and PCU Registers .................................. 56 PCLATH and PCLATU Registers .............................. 56 Program Memory and Extended Instruction Set .................................... 75 Code Protection ....................................................... 255 Instructions ................................................................ 60 Two-Word .......................................................... 60 Interrupt Vector .......................................................... 55 Look-up Tables .......................................................... 58 Map and Stack (diagram) .......................................... 55 Reset Vector .............................................................. 55 Program Verification and Code Protection ...................... 253 Associated Registers ............................................... 254 Programming, Device Instructions ................................... 259 PSP. See Parallel Slave Port. Pulse-Width Modulation. See PWM (CCP Module) and PWM (ECCP Module). PUSH ............................................................................... 288 PUSH and POP Instructions .............................................. 57 PUSHL ............................................................................. 304 PWM (CCP Module) Associated Registers ............................................... 138 Auto-Shutdown (CCP1 only) .................................... 137 CCPR1H:CCPR1L Registers ................................... 141 Duty Cycle ....................................................... 136, 142 Example Frequencies/Resolutions .................. 137, 142 Period .............................................................. 136, 141 Setup for PWM Operation ........................................ 137 TMR2 to PR2 Match ........................................ 136, 141 PWM (ECCP Module) ...................................................... 141 Associated Registers ............................................... 152 Direction Change in Full-Bridge Output Mode ......... 146 Effects of a Reset .................................................... 151 Enhanced PWM Auto-Shutdown ............................. 148 Full-Bridge Application Example .............................. 146 Full-Bridge Mode ..................................................... 145 Half-Bridge Mode ..................................................... 144 Half-Bridge Output Mode Applications Example ...... 144 Operation in Power Managed Modes ...................... 151 Operation with Fail-Safe Clock Monitor ................... 151 Output Configurations .............................................. 142 Output Relationships (Active-High) .......................... 143 Output Relationships (Active-Low) .......................... 143 Programmable Dead-Band Delay ............................ 148 Setup for PWM Operation ........................................ 151 Start-up Considerations ........................................... 150 Q Q Clock .................................................................... 137, 142 R RAM. See Data Memory. RBIF Bit ........................................................................... 100 RC Oscillator ...................................................................... 27 RCIO Oscillator Mode ................................................ 27 RC_IDLE Mode .................................................................. 41 RC_RUN Mode .................................................................. 37 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X RCALL ............................................................................. 289 RCON Register Bit Status During Initialization .................................... 50 Reader Response ............................................................ 376 Register File ....................................................................... 65 Registers ADCON0 (A/D Control 0) ......................................... 213 ADCON1 (A/D Control 1) ......................................... 214 ADCON2 (A/D Control 2) ......................................... 215 BAUDCON (Baud Rate Control) .............................. 196 CCP1CON (Enhanced Capture/Compare/PWM Control 1) ......................................................... 139 CCPxCON (Standard Capture/Compare/PWM Control) .......................................................................... 131 CMCON (Comparator Control) ................................ 223 CONFIG1H (Configuration 1 High) .......................... 240 CONFIG2H (Configuration 2 High) .......................... 242 CONFIG2L (Configuration 2 Low) ............................ 241 CONFIG3H (Configuration 3 High) .......................... 243 CONFIG4L (Configuration 4 Low) ............................ 243 CONFIG5H (Configuration 5 High) .......................... 244 CONFIG5L (Configuration 5 Low) ............................ 244 CONFIG6H (Configuration 6 High) .......................... 245 CONFIG6L (Configuration 6 Low) ............................ 245 CONFIG7H (Configuration 7 High) .......................... 246 CONFIG7L (Configuration 7 Low) ............................ 246 CVRCON (Comparator Voltage Reference Control) 229 Device ID Register 1 ................................................ 247 Device ID Register 2 ................................................ 247 ECCP1AS (ECCP Auto-Shutdown Control) ............. 149 HLVDCON (HLVD Control) ...................................... 233 INTCON (Interrupt Control) ........................................ 85 INTCON2 (Interrupt Control 2) ................................... 86 INTCON3 (Interrupt Control 3) ................................... 87 IPR1 (Peripheral Interrupt Priority 1) .......................... 92 IPR2 (Peripheral Interrupt Priority 2) .......................... 93 OSCCON (Oscillator Control) .................................... 32 OSCTUNE (Oscillator Tuning) ................................... 29 PIE1 (Peripheral Interrupt Enable 1) .......................... 90 PIE2 (Peripheral Interrupt Enable 2) .......................... 91 PIR1 (Peripheral Interrupt Request (Flag) 1) ............. 88 PIR2 (Peripheral Interrupt Request (Flag) 2) ............. 89 PWM1CON (PWM Configuration) ............................ 148 RCON (Reset Control) ......................................... 44, 94 RCSTA (Receive Status and Control) ...................... 195 SSPCON1 (MSSP Control 1, I2C Mode) ................. 164 SSPCON1 (MSSP Control 1, SPI Mode) ................. 155 SSPCON2 (MSSP Control 2, I2C Mode) ................. 165 SSPSTAT (MSSP Status, I2C Mode) ....................... 163 SSPSTAT (MSSP Status, SPI Mode) ...................... 154 Status ......................................................................... 70 STKPTR (Stack Pointer) ............................................ 57 T0CON (Timer0 Control) .......................................... 115 T1CON (Timer1 Control) .......................................... 119 T2CON (Timer 2 Control) ......................................... 125 T3CON (Timer3 Control) .......................................... 127 TRISE (PORTE/PSP Control) .................................. 110 TXSTA (Transmit Status and Control) ..................... 194 WDTCON (Watchdog Timer Control) ...................... 249 RESET ............................................................................. 289 Reset State of Registers .................................................... 50 Resets ........................................................................ 43, 239 Brown-out Reset (BOR) ........................................... 239 Oscillator Start-up Timer (OST) ............................... 239 Power-on Reset (POR) ............................................ 239 (c) 2009 Microchip Technology Inc. Power-up Timer (PWRT) ......................................... 239 RETFIE ............................................................................ 290 RETLW ............................................................................ 290 RETURN .......................................................................... 291 Return Address Stack ........................................................ 56 Return Stack Pointer (STKPTR) ........................................ 57 Revision History ............................................................... 361 RLCF ............................................................................... 291 RLNCF ............................................................................. 292 RRCF ............................................................................... 292 RRNCF ............................................................................ 293 S SCK ................................................................................. 153 SDI ................................................................................... 153 SDO ................................................................................. 153 SEC_IDLE Mode ............................................................... 40 SEC_RUN Mode ................................................................ 36 Serial Clock, SCK ............................................................ 153 Serial Data In (SDI) .......................................................... 153 Serial Data Out (SDO) ..................................................... 153 Serial Peripheral Interface. See SPI Mode. SETF ............................................................................... 293 Single-Supply ICSP Programming. Slave Select (SS) ............................................................. 153 SLEEP ............................................................................. 294 Sleep OSC1 and OSC2 Pin States ...................................... 33 Software Simulator (MPLAB SIM) ................................... 311 Special Event Trigger. See Compare (ECCP Mode). Special Event Trigger. See Compare (ECCP Module). Special Features of the CPU ........................................... 239 Special Function Registers ................................................ 66 Map ............................................................................ 66 SPI Mode (MSSP) Associated Registers ............................................... 161 Bus Mode Compatibility ........................................... 161 Effects of a Reset .................................................... 161 Enabling SPI I/O ...................................................... 157 Master Mode ............................................................ 158 Master/Slave Connection ........................................ 157 Operation ................................................................. 156 Operation in Power Managed Modes ...................... 161 Serial Clock ............................................................. 153 Serial Data In ........................................................... 153 Serial Data Out ........................................................ 153 Slave Mode .............................................................. 159 Slave Select ............................................................. 153 Slave Select Synchronization .................................. 159 SPI Clock ................................................................. 158 Typical Connection .................................................. 157 SS .................................................................................... 153 SSPOV ............................................................................ 183 SSPOV Status Flag ......................................................... 183 SSPSTAT Register R/W Bit ............................................................ 166, 167 Stack Full/Underflow Resets .............................................. 58 SUBFSR .......................................................................... 305 SUBFWB ......................................................................... 294 SUBLW ............................................................................ 295 SUBULNK ........................................................................ 305 SUBWF ............................................................................ 295 SUBWFB ......................................................................... 296 SWAPF ............................................................................ 296 DS39636D-page 371 PIC18F2X1X/4X1X T Table Pointer Operations (table) ........................................ 78 Table Reads/Table Writes .................................................. 58 TBLRD ............................................................................. 297 TBLWT ............................................................................. 298 Time-out in Various Situations (table) ................................ 47 Timer0 .............................................................................. 115 16-Bit Mode Timer Reads and Writes ...................... 116 Associated Registers ............................................... 117 Clock Source Edge Select (T0SE Bit) ...................... 116 Clock Source Select (T0CS Bit) ............................... 116 Operation ................................................................. 116 Overflow Interrupt .................................................... 117 Prescaler .................................................................. 117 Prescaler. See Prescaler, Timer0. Timer1 .............................................................................. 119 16-Bit Read/Write Mode ........................................... 121 Associated Registers ............................................... 123 Interrupt .................................................................... 122 Operation ................................................................. 120 Oscillator .......................................................... 119, 121 Oscillator Layout Considerations ............................. 122 Overflow Interrupt .................................................... 119 Resetting, Using the CCP Special Event Trigger ..... 122 Special Event Trigger (ECCP) ................................. 140 TMR1H Register ...................................................... 119 TMR1L Register ....................................................... 119 Use as a Real-Time Clock ....................................... 122 Timer2 .............................................................................. 125 Associated Registers ............................................... 126 Interrupt .................................................................... 126 Operation ................................................................. 125 Output ...................................................................... 126 PR2 Register .................................................... 136, 141 TMR2 to PR2 Match Interrupt .......................... 136, 141 Timer3 .............................................................................. 127 16-Bit Read/Write Mode ........................................... 129 Associated Registers ............................................... 129 Operation ................................................................. 128 Oscillator .......................................................... 127, 129 Overflow Interrupt ............................................ 127, 129 Special Event Trigger (CCP) .................................... 129 TMR3H Register ...................................................... 127 TMR3L Register ....................................................... 127 Timing Diagrams A/D Conversion ........................................................ 350 Acknowledge Sequence .......................................... 186 Asynchronous Reception ......................................... 205 Asynchronous Transmission .................................... 203 Asynchronous Transmission (Back to Back) ........... 203 Automatic Baud Rate Calculation ............................ 201 Auto-Wake-up Bit (WUE) During Normal Operation 206 Auto-Wake-up Bit (WUE) During Sleep ................... 206 Baud Rate Generator with Clock Arbitration ............ 180 BRG Overflow Sequence ......................................... 201 BRG Reset Due to SDA Arbitration During Start Condition ................................................................... 189 Brown-out Reset (BOR) ........................................... 336 Bus Collision During a Repeated Start Condition (Case 1) ...................................................................... 190 Bus Collision During a Repeated Start Condition (Case 2) ...................................................................... 190 Bus Collision During a Start Condition (SCL = 0) .... 189 Bus Collision During a Start Condition (SDA only) .. 188 Bus Collision During a Stop Condition (Case 1) ...... 191 DS39636D-page 372 Bus Collision During a Stop Condition (Case 2) ...... 191 Bus Collision for Transmit and Acknowledge .......... 187 Capture/Compare/PWM (CCP) ............................... 338 CLKO and I/O .......................................................... 335 Clock Synchronization ............................................. 173 Clock/Instruction Cycle .............................................. 59 Example SPI Master Mode (CKE = 0) ..................... 340 Example SPI Master Mode (CKE = 1) ..................... 341 Example SPI Slave Mode (CKE = 0) ....................... 342 Example SPI Slave Mode (CKE = 1) ....................... 343 External Clock (All Modes except PLL) ................... 333 Fail-Safe Clock Monitor ........................................... 252 First Start Bit Timing ................................................ 181 Full-Bridge PWM Output .......................................... 145 Half-Bridge PWM Output ......................................... 144 High/Low-Voltage Detect Characteristics ................ 330 High-Voltage Detect (VDIRMAG = 1) ...................... 236 I2C Bus Data ............................................................ 344 I2C Bus Start/Stop Bits ............................................ 344 I2C Master Mode (7 or 10-Bit Transmission) ........... 184 I2C Master Mode (7-Bit Reception) .......................... 185 I2C Slave Mode (10-Bit Reception, SEN = 0) .......... 170 I2C Slave Mode (10-Bit Reception, SEN = 1) .......... 175 I2C Slave Mode (10-Bit Transmission) .................... 171 I2C Slave Mode (7-Bit Reception, SEN = 0) ............ 168 I2C Slave Mode (7-Bit Reception, SEN = 1) ............ 174 I2C Slave Mode (7-Bit Transmission) ...................... 169 I2C Slave Mode General Call Address Sequence (7 or 10-Bit Address Mode) ...................................... 176 I2C Stop Condition Receive or Transmit Mode ........ 186 Low-Voltage Detect (VDIRMAG = 0) ....................... 235 Master SSP I2C Bus Data ........................................ 346 Master SSP I2C Bus Start/Stop Bits ........................ 346 Parallel Slave Port (PIC18F4410/4510/4515/4610) . 339 Parallel Slave Port (PSP) Read ............................... 113 Parallel Slave Port (PSP) Write ............................... 113 PWM Auto-Shutdown (PRSEN = 0, Auto-Restart Disabled) .................................... 150 PWM Auto-Shutdown (PRSEN = 1, Auto-Restart Enabled) ..................................... 150 PWM Direction Change ........................................... 147 PWM Direction Change at Near 100% Duty Cycle .. 147 PWM Output ............................................................ 136 Repeat Start Condition ............................................ 182 Reset, Watchdog Timer (WDT), Oscillator Start-up Timer (OST), Power-up Timer (PWRT) ..................... 336 Send Break Character Sequence ............................ 207 Slave Synchronization ............................................. 159 Slow Rise Time (MCLR Tied to VDD, VDD Rise > TPWRT) ............................................................................ 49 SPI Mode (Master Mode) ......................................... 158 SPI Mode (Slave Mode, CKE = 0) ........................... 160 SPI Mode (Slave Mode, CKE = 1) ........................... 160 Synchronous Reception (Master Mode, SREN) ...... 210 Synchronous Transmission ..................................... 208 Synchronous Transmission (Through TXEN) .......... 209 Time-out Sequence on POR w/PLL Enabled (MCLR Tied to VDD) ............................................................... 49 Time-out Sequence on Power-up (MCLR Not Tied to VDD, Case 1) ................................................. 48 Time-out Sequence on Power-up (MCLR Not Tied to VDD, Case 2) ................................................. 48 Time-out Sequence on Power-up (MCLR Tied to VDD, VDD Rise < TPWRT) ............................................ 48 Timer0 and Timer1 External Clock .......................... 337 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X Transition for Entry to Idle Mode ................................ 40 Transition for Entry to SEC_RUN Mode .................... 37 Transition for Entry to Sleep Mode ............................ 39 Transition for Two-Speed Start-up (INTOSC to HSPLL) 250 Transition for Wake from Idle to Run Mode ............... 40 Transition for Wake from Sleep (HSPLL) ................... 39 Transition from RC_RUN Mode to PRI_RUN Mode .. 38 Transition from SEC_RUN Mode to PRI_RUN Mode (HSPLL) ............................................................. 37 Transition to RC_RUN Mode ..................................... 38 USART Synchronous Receive (Master/Slave) ........ 348 USART Synchronous Transmission (Master/Slave) 348 Timing Diagrams and Specifications ................................ 333 A/D Conversion Requirements ................................ 350 Capture/Compare/PWM (CCP) Requirements ........ 338 CLKO and I/O Requirements ................................... 335 Example SPI Mode Requirements (Master Mode, CKE = 0) .......................................................... 340 Example SPI Mode Requirements (Master Mode, CKE = 1) .......................................................... 341 Example SPI Mode Requirements (Slave Mode, CKE = 0) .......................................................... 342 Example SPI Mode Requirements (Slave Mode, CKE = 1) .......................................................... 343 External Clock Requirements .................................. 333 I2C Bus Data Requirements (Slave Mode) .............. 345 Master SSP I2C Bus Data Requirements ................ 347 Master SSP I2C Bus Start/Stop Bits Requirements . 346 Parallel Slave Port Requirements (PIC18F4410/4510/ 4515/4610) ....................................................... 339 PLL Clock ................................................................. 334 Reset, Watchdog Timer, Oscillator Start-up Timer, Power-up Timer and Brown-out Reset Requirements .. 336 Timer0 and Timer1 External Clock Requirements ... 337 USART Synchronous Receive Requirements ......... 348 USART Synchronous Transmission Requirements . 348 Top-of-Stack Access .......................................................... 56 TRISE Register PSPMODE Bit .......................................................... 106 TSTFSZ ........................................................................... 299 Two-Speed Start-up ................................................. 239, 250 Two-Word Instructions Example Cases .......................................................... 60 TXSTA Register BRGH Bit ................................................................. 197 V Voltage Reference Specifications .................................... 329 W Watchdog Timer (WDT) ........................................... 239, 248 Associated Registers ............................................... 249 Control Register ....................................................... 248 During Oscillator Failure .......................................... 251 Programming Considerations .................................. 248 WCOL ...................................................... 181, 182, 183, 186 WCOL Status Flag ................................... 181, 182, 183, 186 WWW Address ................................................................. 375 WWW, On-Line Support ...................................................... 8 X XORLW ............................................................................ 299 XORWF ............................................................................ 300 (c) 2009 Microchip Technology Inc. DS39636D-page 373 PIC18F2X1X/4X1X DS39636D-page 374 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives * * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. (c) 2009 Microchip Technology Inc. DS39636D-page 375 PIC18F2X1X/4X1X READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y Device: PIC18F2X1X/4X1X N Literature Number: DS39636D Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS39636D-page 376 (c) 2009 Microchip Technology Inc. PIC18F2X1X/4X1X PIC18F2X1X/4X1X PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX XXX Device Temperature Range Package Pattern Examples: a) b) Device PIC18F2410/2415/2510/2515/2610(1), PIC18F4410/4415/4510/4515/4610(1), PIC18F2410/2415/2510/2515/2610T(2), PIC18F4410/4415/4510/4515/4610 T(2); VDD range 4.2V to 5.5V PIC18LF2410/2510/2515/2610(1), PIC18LF4410/4510/4515/4610(1), PIC18LF2410/2510/2515/2610T(2), PIC18LF4410/4510/4515/4610T(2); VDD range 2.0V to 5.5V Temperature Range I E = = Package PT SO SP P ML = = = = = Pattern QTP, SQTP, Code or Special Requirements (blank otherwise) -40C to +85C (Industrial) -40C to +125C (Extended) c) PIC18LF4510-I/P 301 = Industrial temp., PDIP package, Extended VDD limits, QTP pattern #301. PIC18LF2410-I/SO = Industrial temp., SOIC package, Extended VDD limits. PIC18F4410-I/P = Industrial temp., PDIP package, normal VDD limits. Note 1: 2: TQFP (Thin Quad Flatpack) SOIC Skinny Plastic DIP PDIP QFN (c) 2009 Microchip Technology Inc. F = Standard Voltage Range LF = Wide Voltage Range T = in tape and reel TQFP packages only. DS39636D-page 377 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS39636D-page 378 (c) 2009 Microchip Technology Inc.