MC74AC02, MC74ACT02 Quad 2-Input NOR Gate * Outputs Source/Sink 24 mA * ACT02 Has TTL Compatible Inputs VCC 14 http://onsemi.com 13 12 11 10 9 8 PDIP-14 N SUFFIX CASE 646 14 1 1 2 3 4 5 6 7 SO-14 D SUFFIX CASE 751A 14 1 GND Figure 1. Pinout: 14-Lead Packages Conductors (Top View) 14 1 MAXIMUM RATINGS* Rating Symbol Value Unit DC Supply Voltage (Referenced to GND) VCC -0.5 to +7.0 V 14 DC Input Voltage (Referenced to GND) Vin -0.5 to VCC +0.5 V DC Output Voltage (Referenced to GND) Vout -0.5 to VCC +0.5 V Iin 20 mA DC Output Sink/Source Current, per Pin Iout 50 mA DC VCC or GND Current per Output Pin ICC 50 mA Storage Temperature Tstg -65 to +150 C DC Input Current, per Pin *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. 1 TSSOP-14 DT SUFFIX CASE 948G EIAJ-14 M SUFFIX CASE 965 ORDERING INFORMATION Device Package Shipping MC74AC02N PDIP-14 25 Units/Rail MC74ACT02N PDIP-14 25 Units/Rail MC74AC02D SOIC-14 55 Units/Rail MC74AC02DR2 SOIC-14 2500 Tape & Reel MC74ACT02D SOIC-14 55 Units/Rail MC74ACT02DR2 SOIC-14 2500 Tape & Reel MC74AC02DT TSSOP-14 96 Units/Rail MC74AC02DTR2 TSSOP-14 2500 Tape & Reel MC74ACT02DT TSSOP-14 MC74ACT02DTR2 TSSOP-14 2500 Tape & Reel 96 Units/Rail MC74AC02M EIAJ-14 50 Units/Rail MC74AC02MEL EIAJ-14 2000 Tape & Reel MC74ACT02M EIAJ-14 50 Units/Rail MC74ACT02MEL EIAJ-14 2000 Tape & Reel DEVICE MARKING INFORMATION See general marking information in the device marking section on page 5 of this data sheet. Semiconductor Components Industries, LLC, 2001 May, 2001 - Rev. 5 1 Publication Order Number: MC74AC02/D MC74AC02, MC74ACT02 RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) AC Devices except Schmitt Inputs Min Typ Max Unit AC 2.0 5.0 6.0 ACT 4.5 5.0 5.5 0 - VCC VCC @ 3.0 V - 150 - VCC @ 4.5 V - 40 - VCC @ 5.5 V - 25 - VCC @ 4.5 V - 10 - VCC @ 5.5 V - 8.0 - - - 140 C -40 25 85 C V V ns/V tr, tf In ut Rise and Fall Time (Note 2) Input ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH Output Current - High - - -24 mA IOL Output Current - Low - - 24 mA ns/V 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. DC CHARACTERISTICS Symbol Parameter VCC (V) 74AC 74AC TA = +25C TA = -40C to +85C Typ VIH VIL VOH VOL Guaranteed Limits 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC - 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC - 0.1 V Minimum High g Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 3.0 4.5 5.5 - - - 2.56 3.86 4.86 2.46 3.76 4.76 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 - - - 0.36 0.36 0.36 0.44 0.44 0.44 55 5.5 - 0 1 0.1 5.5 - 5.5 55 5.5 Maximum Low Level Output Voltage Maximum Input Leakage Current IOLD Minimum Dynamic O t t Current Output C t ICC Conditions Minimum High g Level Input Voltage IIN IOHD Unit Maximum Q Quiescent Supply Current V *VIN = VIL or VIH -12 mA IOH -24 mA -24 mA IOUT = 50 A V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA 1 0 1.0 A VI = VCC, GND - 75 mA VOLD = 1.65 V Max - - -75 mA VOHD = 3.85 V Min - 40 4.0 40 A VIN = VCC or GND *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC. http://onsemi.com 2 IOUT = -50 A MC74AC02, MC74ACT02 AC CHARACTERISTICS (For Figures and Waveforms - See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74AC 74AC TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay 3.3 5.0 1.5 1.5 5.0 4.0 7.5 6.0 1.0 1.0 8.0 6.5 ns 3-5 tPHL Propagation Delay 3.3 5.0 1.5 1.5 5.0 4.5 7.5 6.5 1.0 1.0 8.0 7.0 ns 3-5 *Voltage Range 3.3 V is 3.3 V 0.3 V. Voltage Range 5.0 V is 5.0 V 0.5 V. DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25C TA = -40C to +85C Typ Guaranteed Limits Unit Conditions VIH Minimum High g Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC - 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC - 0.1 V VOH Minimum High g Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 4.5 5.5 - - 3.86 4.86 3.76 4.76 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 4.5 5.5 - - 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOL 24 mA VOL Maximum Low Level Output Voltage V V IOUT = -50 A *VIN = VIL or VIH -24 mA IOH -24 mA IOUT = 50 A IIN Maximum Input Leakage Current 55 5.5 - 0 1 0.1 1 0 1.0 A VI = VCC, GND ICCT Additional Max. ICC/Input 5.5 0.6 - 1.5 mA VI = VCC - 2.1 V IOLD Minimum Dynamic O t t Current Output C t 5.5 - - 75 mA VOLD = 1.65 V Max 5.5 - - -75 mA VOHD = 3.85 V Min 55 5.5 - 40 4.0 40 A VIN = VCC or GND IOHD ICC Maximum Q Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. http://onsemi.com 3 MC74AC02, MC74ACT02 AC CHARACTERISTICS (For Figures and Waveforms - See Section 3 of the ON Semiconductor FACT Data Book, DL138/D) Symbol VCC* (V) Parameter 74ACT 74ACT TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit Fig. No. tPLH Propagation Delay 5.0 1.5 - 8.5 1.0 9.0 ns 3-6 tPHL Propagation Delay 5.0 1.5 - 9.5 1.0 10 ns 3-6 *Voltage Range 5.0 V is 5.0 V 0.5 V. CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V http://onsemi.com 4 MC74AC02, MC74ACT02 MARKING DIAGRAMS PDIP-14 SO-14 TSSOP-14 EIAJ-14 MC74AC02N AWLYYWW AC02 AWLYWW AC 02 ALYW 74AC02 ALYW MC74ACT02N AWLYYWW ACT02 AWLYWW ACT 02 ALYW 74ACT02 ALYW A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week http://onsemi.com 5 MC74AC02, MC74ACT02 PACKAGE DIMENSIONS PDIP-14 N SUFFIX 14 PIN PLASTIC DIP PACKAGE CASE 646-06 ISSUE M 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. 8 B 1 7 A F DIM A B C D F G H J K L M N L N C -T- SEATING PLANE J K H D 14 PL G 0.13 (0.005) M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 8 -B- 1 P 7 PL 0.25 (0.010) 7 G M B M F R X 45 C -T- SEATING PLANE D 14 PL 0.25 (0.010) M T B J M K S A MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --10 0.38 1.01 M SO-14 D SUFFIX 14 PIN PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE F 14 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --10 0.015 0.039 S http://onsemi.com 6 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.228 0.244 0.010 0.019 MC74AC02, MC74ACT02 PACKAGE DIMENSIONS TSSOP-14 DT SUFFIX 14 PIN PLASTIC TSSOP PACKAGE CASE 948G-01 ISSUE O 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 0.25 (0.010) 8 M B -U- L PIN 1 IDENT. F 7 1 0.15 (0.006) T U N S DETAIL E K A -V- CCC EE CCC EE K1 J J1 SECTION N-N -W- C 0.10 (0.004) -T- SEATING PLANE H G D DETAIL E EIAJ-14 M SUFFIX 14 PIN PLASTIC EIAJ PACKAGE CASE 965-01 ISSUE O 14 LE 8 Q1 E HE L 7 1 M DETAIL P Z D VIEW P A e c b 0.13 (0.005) A1 M 0.10 (0.004) http://onsemi.com 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS INCHES DIM MIN MAX MIN MAX A 4.90 5.10 0.193 0.200 B 4.30 4.50 0.169 0.177 C --1.20 --0.047 D 0.05 0.15 0.002 0.006 F 0.50 0.75 0.020 0.030 G 0.65 BSC 0.026 BSC H 0.50 0.60 0.020 0.024 J 0.09 0.20 0.004 0.008 J1 0.09 0.16 0.004 0.006 K 0.19 0.30 0.007 0.012 K1 0.19 0.25 0.007 0.010 L 6.40 BSC 0.252 BSC M 0 8 0 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE 0.50 LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 0 10 0.70 0.90 --1.42 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 0 10 0.028 0.035 --0.056 MC74AC02, MC74ACT02 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 MC74AC02/D