Semiconductor Components Industries, LLC, 2001
May, 2001 – Rev. 5 1Publication Order Number:
MC74AC02/D
MC74AC02, MC74ACT02
Quad 2-Input NOR Gate
•Outputs Source/Sink 24 mA
•′ACT02 Has TTL Compatible Inputs
1314 12 11 10 9 8
21 34567
GND
VCC
Figure 1. Pinout: 14–Lead Packages Conductors
(Top V iew)
MAXIMUM RATINGS*
Rating Symbol Value Unit
DC Supply Voltage (Referenced to GND) VCC –0.5 to
+7.0 V
DC Input Voltage (Referenced to GND) Vin –0.5 to
VCC +0.5 V
DC Output Voltage (Referenced to GND) Vout –0.5 to
VCC +0.5 V
DC Input Current, per Pin Iin ±20 mA
DC Output Sink/Source Current, per Pin Iout ±50 mA
DC VCC or GND Current per Output Pin ICC ±50 mA
Storage Temperature Tstg –65 to
+150 °C
*Maximum Ratings are those values beyond which damage to the device may
occur. Functional operation should be restricted to the Recommended Operating
Conditions.
TSSOP–14
DT SUFFIX
CASE 948G
1
14
EIAJ–14
M SUFFIX
CASE 965
1
14
SO–14
D SUFFIX
CASE 751A
http://onsemi.com
1
14
1
14
PDIP–14
N SUFFIX
CASE 646
Device Package Shipping
ORDERING INFORMATION
MC74AC02DT TSSOP–14 96 Units/Rail
MC74AC02DTR2 TSSOP–14 2500 Tape & Reel
MC74ACT02DT TSSOP–14 96 Units/Rail
MC74ACT02DTR2 TSSOP–14 2500 Tape & Reel
MC74AC02N PDIP–14 25 Units/Rail
MC74AC02D SOIC–14 55 Units/Rail
MC74ACT02N PDIP–14 25 Units/Rail
MC74AC02DR2 SOIC–14 2500 Tape & Reel
MC74ACT02D SOIC–14 55 Units/Rail
MC74ACT02DR2 SOIC–14 2500 Tape & Reel
MC74AC02M EIAJ–14 50 Units/Rail
MC74AC02MEL EIAJ–14 2000 Tape & Reel
MC74ACT02M EIAJ–14 50 Units/Rail
MC74ACT02MEL EIAJ–14 2000 Tape & Reel
See general marking information in the device marking
section on page 5 of this data sheet.
DEVICE MARKING INFORMATION
MC74AC02, MC74ACT02
http://onsemi.com
2
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Typ Max Unit
V
Supply Voltage
′AC 2.0 5.0 6.0
V
VCC Supply Voltage ′ACT 4.5 5.0 5.5 V
Vin, Vout DC Input V oltage, Output Voltage (Ref. to GND) 0 – VCC V
VCC @ 3.0 V – 150 –
tr, tfInput Rise and Fall Time (Note 1)
′
AC Devices exce
p
t Schmitt In
p
uts
VCC @ 4.5 V – 40 – ns/V
r,f
′AC
Devices
except
Schmitt
Inputs
VCC @ 5.5 V – 25 –
tt
f
Input Rise and Fall Time (Note 2) VCC @ 4.5 V – 10 –
ns/V
tr, tf
In ut
Rise
and
Fall
Time
(Note
2)
′ACT Devices except Schmitt Inputs VCC @ 5.5 V – 8.0 – ns/V
TJJunction Temperature (PDIP) – – 140 °C
TAOperating Ambient Temperature Range –40 25 85 °C
IOH Output Current – High – – –24 mA
IOL Output Current – Low – – 24 mA
1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that dif fer from the typical input rise and fall times.
2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times.
DC CHARACTERISTICS
74AC 74AC
Symbol Parameter VCC
(V) TA = +25°CTA =
–40°C to
+85°CUnit Conditions
Typ Guaranteed Limits
VIH Minimum High Level 3.0 1.5 2.1 2.1 VOUT = 0.1 V
g
Input Voltage 4.5 2.25 3.15 3.15 V or VCC – 0.1 V
5.5 2.75 3.85 3.85
VIL Maximum Low Level 3.0 1.5 0.9 0.9 VOUT = 0.1 V
Input Voltage 4.5 2.25 1.35 1.35 V or VCC – 0.1 V
5.5 2.75 1.65 1.65
VOH Minimum High Level 3.0 2.99 2.9 2.9 IOUT = –50 µA
g
Output Voltage 4.5 4.49 4.4 4.4 V
5.5 5.49 5.4 5.4
*VIN = VIL or VIH
3.0 – 2.56 2.46
V
–12 mA
4.5 – 3.86 3.76
V
IOH –24 mA
5.5 – 4.86 4.76 –24 mA
VOL Maximum Low Level 3.0 0.002 0.1 0.1 IOUT = 50 µA
Output Voltage 4.5 0.001 0.1 0.1 V
5.5 0.001 0.1 0.1
*VIN = VIL or VIH
3.0 – 0.36 0.44
V
12 mA
4.5 – 0.36 0.44
V
IOL 24 mA
5.5 – 0.36 0.44 24 mA
IIN Maximum Input
55
–
±01
±10
µA
VI=V
CC GND
Leakage Current 5.5 – ±
0
.
1
±
1
.
0
µ
A
V
I =
V
CC,
GND
IOLD †Minimum Dynamic
Ot tC t
5.5 – – 75 mA VOLD = 1.65 V Max
IOHD Output Current 5.5 – – –75 mA VOHD = 3.85 V Min
ICC Maximum Quiescent
55
–
40
40
µA
VIN =V
CC or GND
Q
Supply Current 5.5 –
4
.
0
40
µ
A
V
IN =
V
CC or
GND
*All outputs loaded; thresholds on input associated with output under test.
†Maximum test duration 2.0 ms, one output loaded at a time.
NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC.
MC74AC02, MC74ACT02
http://onsemi.com
3
AC CHARACTERISTICS (For Figures and W aveforms – See Section 3 of the ON Semiconductor FACT Data Book, DL138/D)
74AC 74AC
Symbol Parameter VCC*
(V) TA = +25°C
CL = 50 pF
TA = –40°C
to +85°C
CL = 50 pF Unit Fig.
No.
Min Typ Max Min Max
tPLH
Pro
p
agation Delay
3.3 1.5 5.0 7.5 1.0 8.0
ns
3
–
5
tPLH
P
ropagat
i
on
D
e
l
ay 5.0 1.5 4.0 6.0 1.0 6.5 ns
3
–5
tPHL
Pro
p
agation Delay
3.3 1.5 5.0 7.5 1.0 8.0
ns
3
–
5
tPHL
P
ropagat
i
on
D
e
l
ay 5.0 1.5 4.5 6.5 1.0 7.0 ns
3
–5
*Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
DC CHARACTERISTICS
74ACT 74ACT
Symbol Parameter VCC
(V) TA = +25°CTA =
–40°C to
+85°CUnit Conditions
Typ Guaranteed Limits
VIH Minimum High Level 4.5 1.5 2.0 2.0
V
VOUT = 0.1 V
g
Input Voltage 5.5 1.5 2.0 2.0
V
or VCC – 0.1 V
VIL Maximum Low Level 4.5 1.5 0.8 0.8
V
VOUT = 0.1 V
Input Voltage 5.5 1.5 0.8 0.8
V
or VCC – 0.1 V
VOH Minimum High Level 4.5 4.49 4.4 4.4
V
IOUT = –50 µA
g
Output Voltage 5.5 5.49 5.4 5.4
V
*VIN = VIL or VIH
4.5 – 3.86 3.76 V
IOH
–24 mA
5.5 – 4.86 4.76
I
OH –24 mA
VOL Maximum Low Level 4.5 0.001 0.1 0.1
V
IOUT = 50 µA
Output Voltage 5.5 0.001 0.1 0.1
V
*VIN = VIL or VIH
4.5 – 0.36 0.44 V
IOL
24 mA
5.5 – 0.36 0.44
I
OL 24 mA
IIN Maximum Input
55
–
±01
±10
µA
VI=V
CC GND
Leakage Current 5.5 – ±
0
.
1
±
1
.
0
µ
A
V
I =
V
CC,
GND
∆ICCT Additional Max. ICC/Input 5.5 0.6 – 1.5 mA VI = VCC – 2.1 V
IOLD †Minimum Dynamic
Ot tC t
5.5 – – 75 mA VOLD = 1.65 V Max
IOHD Output Current 5.5 – – –75 mA VOHD = 3.85 V Min
ICC Maximum Quiescent
55
–
40
40
µA
VIN =V
CC or GND
Q
Supply Current 5.5 –
4
.
0
40
µ
A
V
IN =
V
CC or
GND
*All outputs loaded; thresholds on input associated with output under test.
†Maximum test duration 2.0 ms, one output loaded at a time.
MC74AC02, MC74ACT02
http://onsemi.com
4
AC CHARACTERISTICS (For Figures and W aveforms – See Section 3 of the ON Semiconductor FACT Data Book, DL138/D)
74ACT 74ACT
Symbol Parameter VCC*
(V) TA = +25°C
CL = 50 pF
TA = –40°C
to +85°C
CL = 50 pF Unit Fig.
No.
Min Typ Max Min Max
tPLH Propagation Delay 5.0 1.5 – 8.5 1.0 9.0 ns 3–6
tPHL Propagation Delay 5.0 1.5 – 9.5 1.0 10 ns 3–6
*Voltage Range 5.0 V is 5.0 V ±0.5 V.
CAPACITANCE
Symbol Parameter Value
Typ Unit Test Conditions
CIN Input Capacitance 4.5 pF VCC = 5.0 V
CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V
MC74AC02, MC74ACT02
http://onsemi.com
5
MARKING DIAGRAMS
A = Assembly Location
WL, L = W afer Lot
YY, Y = Year
WW, W = W ork Week
PDIP–14 SO–14 TSSOP–14
MC74AC02N
AWLYYWW AC02
AWLYWW AC
02
ALYW
ACT
02
ALYW
ACT02
AWLYWW
MC74ACT02N
AWLYYWW
74AC02
ALYW
EIAJ–14
74ACT02
ALYW
MC74AC02, MC74ACT02
http://onsemi.com
6
PACKAGE DIMENSIONS
PDIP–14
N SUFFIX
14 PIN PLASTIC DIP PACKAGE
CASE 646–06
ISSUE M
17
14 8
B
ADIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.715 0.770 18.16 18.80
B0.240 0.260 6.10 6.60
C0.145 0.185 3.69 4.69
D0.015 0.021 0.38 0.53
F0.040 0.070 1.02 1.78
G0.100 BSC 2.54 BSC
H0.052 0.095 1.32 2.41
J0.008 0.015 0.20 0.38
K0.115 0.135 2.92 3.43
L
M--- 10 --- 10
N0.015 0.039 0.38 1.01
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
5. ROUNDED CORNERS OPTIONAL.
F
HG DK
C
SEATING
PLANE
N
–T–
14 PL
M
0.13 (0.005)
L
M
J0.290 0.310 7.37 7.87
SO–14
D SUFFIX
14 PIN PLASTIC SOIC PACKAGE
CASE 751A–03
ISSUE F NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
–A–
–B–
G
P7 PL
14 8
71 M
0.25 (0.010) B M
S
B
M
0.25 (0.010) A S
T
–T–
F
RX 45
SEATING
PLANE D14 PL K
C
J
M
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A8.55 8.75 0.337 0.344
B3.80 4.00 0.150 0.157
C1.35 1.75 0.054 0.068
D0.35 0.49 0.014 0.019
F0.40 1.25 0.016 0.049
G1.27 BSC 0.050 BSC
J0.19 0.25 0.008 0.009
K0.10 0.25 0.004 0.009
M0 7 0 7
P5.80 6.20 0.228 0.244
R0.25 0.50 0.010 0.019
MC74AC02, MC74ACT02
http://onsemi.com
7
PACKAGE DIMENSIONS
TSSOP–14
DT SUFFIX
14 PIN PLASTIC TSSOP PACKAGE
CASE 948G–01
ISSUE O
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A4.90 5.10 0.193 0.200
B4.30 4.50 0.169 0.177
C--- 1.20 --- 0.047
D0.05 0.15 0.002 0.006
F0.50 0.75 0.020 0.030
G0.65 BSC 0.026 BSC
H0.50 0.60 0.020 0.024
J0.09 0.20 0.004 0.008
J1 0.09 0.16 0.004 0.006
K0.19 0.30 0.007 0.012
K1 0.19 0.25 0.007 0.010
L6.40 BSC 0.252 BSC
M0 8 0 8
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE -W-.
S
U0.15 (0.006) T
2X L/2
S
U
M
0.10 (0.004) V S
T
L–U–
SEATING
PLANE
0.10 (0.004)
–T–
ÇÇÇ
ÇÇÇ
SECTION N–N
DETAIL E
JJ1
K
K1
ÉÉ
ÉÉ
DETAIL E
F
M
–W–
0.25 (0.010)
8
14
7
1
PIN 1
IDENT.
H
G
A
D
C
B
S
U0.15 (0.006) T
–V–
14X REFK
N
N
EIAJ–14
M SUFFIX
14 PIN PLASTIC EIAJ PACKAGE
CASE 965–01
ISSUE O
HE
A1
DIM MIN MAX MIN MAX
INCHES
--- 2.05 --- 0.081
MILLIMETERS
0.05 0.20 0.002 0.008
0.35 0.50 0.014 0.020
0.18 0.27 0.007 0.011
9.90 10.50 0.390 0.413
5.10 5.45 0.201 0.215
1.27 BSC 0.050 BSC
7.40 8.20 0.291 0.323
0.50 0.85 0.020 0.033
1.10 1.50 0.043 0.059
0
0.70 0.90 0.028 0.035
--- 1.42 --- 0.056
A1
HE
Q1
LE
10 0
10
LEQ1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE
MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD
FLASH OR PROTRUSIONS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL
CONDITION. DAMBAR CANNOT BE LOCATED ON
THE LOWER RADIUS OR THE FOOT. MINIMUM
SPACE BETWEEN PROTRUSIONS AND
ADJACENT LEAD TO BE 0.46 ( 0.018).
0.13 (0.005) M0.10 (0.004)
D
Z
E
1
14 8
7
eA
b
VIEW P
c
L
DETAIL P
M
A
b
c
D
E
e
0.50
M
Z
MC74AC02, MC74ACT02
http://onsemi.com
8
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur . Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: r14525@onsemi.com
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
MC74AC02/D
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
