(R) (R) Cree XLamp XT-E LEDs Product Description FEATURES Table of contents XLamp * Available in white, 80-CRI min white, 70-min CRI white and royal blue Product Characteristics................ 2 XT-E is Cree's highest performing silicon carbide-based LED technology, Cree's delivered industry-standard packaging. in XP/XT XT-E White sets the new standard for high performance and dramatically lowers system cost. XT-E Royal Blue is Cree's highest performing source of royal blue light for remote-phosphor applications. * Binned at 85 C XLamp performance light to LEDs bring and quality high of a wide range of lighting applications, including remote- phosphor, color-changing, portable and personal, outdoor, indoor- directional, transportation, stage and studio, commercial WWW.CREE.COM/XLAMP emergency-vehicle lighting. and Relative Spectral Power Distribution ............................... 4 Relative Luminous Flux vs. * Royal Blue wall plug efficiency of up to 53% (@ 85 C, 350 mA) Electrical Characteristics.............. 6 * Wide viewing angle: 115-140 Current..................................... 6 * Maximum drive current: 1.5 A Cree Flux Characteristics..................... 2 * Cool white efficacy of up to 148 lm/W (@ 85 C, 350 mA) * Thermal resistance: 5 C/W * Electrically neutral thermal path * Vf binning supported for XT-E White and Royal Blue * XT-E Royal Blue sorted into 2.5nm wavelength bins CLD-DS41 Rev 2 Product family data sheet Junction Temperature.................. 5 Relative Luminous Flux vs. Relative Chromaticity vs. Current and Temperature........................ 8 Typical Spatial Distribution........... 9 Thermal Design.........................10 Reflow Soldering Characteristics..11 Notes.......................................12 Mechanical Dimensions..............13 Tape and Reel...........................14 Packaging.................................15 * Unlimited floor life at 30 C/85% RH * Reflow solderable - JEDEC J-STD-020C Compatible * RoHS- and REACH-compliant NOTE: For remote phosphor applications, a separate license to certain Cree patents is required. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, Inc. Cree,Drive Inc. 4600 Silicon 4600 Silicon Drive Durham, NC 27703 NC 27703 USA Tel:Durham, +1.919.313.5300 USA Tel: +1.919.313.5300 www.cree.com/xlamp xlamp XT-E LEDs Product Characteristics Characteristics Unit Minimum Thermal resistance, junction to solder point C/W 5 Viewing angle (FWHM) - white degrees 115 Viewing angle (FWHM) - royal blue degrees 140 Temperature coefficient of voltage mV/C -2.5 ESD classification (HBM per Mil-Std-883D) Typical Maximum Class 2 DC forward current mA 1500 Reverse voltage V 5 Forward voltage (@ 350 mA, 85 C) V LED junction temperature C 2.85 3.4 150 Flux Characteristics - White (TJ = 85 C) The following table provides several base order codes for XLamp XT-E White LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XT-E Binning and Labeling document. Color CCT Range Min. Cool White Outdoor White Neutral White 70 CRI Minimum Neutral White 5,000 K 4,000 K 3,700 K 3,700 K Max. 8,300 K 6,200 K 5,000 K 5,000 K Base Order Codes Minimum Luminous Flux @ 350 mA (lm) Calculated Minimum Luminous Flux (lm)* Order Code Group Flux (lm) 700 mA 1500 mA R3 122 217 369 XTEAWT-00-0000-000000F51 R4 130 231 393 XTEAWT-00-0000-000000G51 R5 139 247 420 XTEAWT-00-0000-000000H51 R3 122 217 369 XTEAWT-00-0000-000000FE3 R4 130 231 393 XTEAWT-00-0000-000000GE3 R5 139 247 420 XTEAWT-00-0000-000000HE3 Q5 107 190 324 XTEAWT-00-0000-00000LFE4 R2 114 203 354 XTEAWT-00-0000-00000LEE4 R3 122 217 369 XTEAWT-00-0000-00000LDE3 Q5 107 190 324 XTEAWT-00-0000-00000BDF5 R2 114 203 354 XTEAWT-00-0000-00000BEF5 R3 122 217 369 XTEAWT-00-0000-00000BFF5 Notes: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. * Typical CRI for Neutral White, 3700 K - 5000K CCT is 75. * Typical CRI for Warm White, 2600 K - 3700 K CCT is 80. * Calculated flux values are for reference only Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 2 xlamp XT-E LEDs Flux Characteristics - White (TJ = 85 C) Base Order Codes Minimum Luminous Flux @ 350 mA (lm) CCT Range Color Min. 80 CRI Minimum White 2,600 K Warm White 2,600 K 70 CRI Minimum Warm White 2,600 K Max. 4,300 K 3,700 K 3,700 K Calculated Minimum Luminous Flux (lm)* Order Code Group Flux (lm) 700 mA 1500 mA Q3 93.9 167 284 XTEAWT-00-0000-00000HBE7 Q4 100 178 302 XTEAWT-00-0000-00000HCE7 Q5 107 190 324 XTEAWT-00-0000-00000HDE7 Q3 93.9 167 284 XTEAWT-00-0000-00000LBE7 Q4 100 178 302 XTEAWT-00-0000-00000LCE7 Q5 107 190 324 XTEAWT-00-0000-00000LDE7 Q4 100 167 284 XTEAWT-00-0000-00000BCE7 Q5 107 178 302 XTEAWT-00-0000-00000BDE7 R2 114 190 324 XTEAWT-00-0000-00000BEE7 Notes: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. * Typical CRI for Neutral White, 3700 K - 5000K CCT is 75. * Typical CRI for Warm White, 2600 K - 3700 K CCT is 80. * Calculated flux values are for reference only Flux Characteristics - Royal Blue (TJ = 85 C) The following table provides order codes for XLamp XT-E Royal Blue LEDs. Additional information on the performance grouping and codes for XT-E Royal Blue LEDs can be found in the XT-E Binning and Labeling document. Dominant Wavelength Range DWL Kit Codes Min. Order Codes, Minimum Radiant Flux @ 350 mA, Tj=85 C Max. Group DWL (nm) Group DWL (nm) 475 mW 500 mW 525 mW 550 mW 01 D36 450 D57 465 XTEARY-00-0000-000000K01 XTEARY-00-0000-000000L01 XTEARY-00-0000-000000M01 XTEARY-00-0000-000000N01 02 D36 450 D47 460 XTEARY-00-0000-000000K02 XTEARY-00-0000-000000L02 XTEARY-00-0000-000000M02 XTEARY-00-0000-000000N02 03 D46 455 D57 465 XTEARY-00-0000-000000K03 XTEARY-00-0000-000000L03 XTEARY-00-0000-000000M03 XTEARY-00-0000-000000N03 04 D36 450 D37 455 XTEARY-00-0000-000000K04 XTEARY-00-0000-000000L04 XTEARY-00-0000-000000M04 XTEARY-00-0000-000000N04 05 D46 455 D47 460 XTEARY-00-0000-000000K05 XTEARY-00-0000-000000L05 XTEARY-00-0000-000000M05 XTEARY-00-0000-000000N05 06 D56 460 D57 465 XTEARY-00-0000-000000K06 XTEARY-00-0000-000000L06 XTEARY-00-0000-000000M06 XTEARY-00-0000-000000N06 07 D37 452.5 D46 457.5 XTEARY-00-0000-000000K07 XTEARY-00-0000-000000L07 XTEARY-00-0000-000000M07 XTEARY-00-0000-000000N07 08 D47 457.5 D56 462.5 XTEARY-00-0000-000000K08 XTEARY-00-0000-000000L08 XTEARY-00-0000-000000M08 XTEARY-00-0000-000000N08 09 D37 452.5 D56 462.5 XTEARY-00-0000-000000K09 XTEARY-00-0000-000000L09 XTEARY-00-0000-000000M09 XTEARY-00-0000-000000N09 Note: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 3 xlamp XT-E LEDs Relative Spectral Power Relative Spectral Power Distribution - White Relative Radiant Power (%) 100 80 60 5000K - 8300K CCT 2600K - 3700K CCT 40 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) Relative sPECTRAL pOWER dISTRIBUTION - Royal Blue Relative Spectral Power Relative Radiant Power (%) 100% 80% 60% Royal Blue 40% 20% 0% 400 450 500 550 600 650 700 750 Wavelength (nm) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 4 xlamp XT-E LEDs Relative Flux Output vs. Junction Temperature mA) - White Relative Luminous Flux vs. Junction Temperature (IF = 350 Relative Luminous Flux 120% 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (C) Relative Flux Output vs. Junction Temperature Relative Radiant Flux vs. Junction Temperature (IF = 350 mA) - Royal Blue Relative Radiant Flux 120% 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (C) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 5 xlamp XT-E LEDs Electrical Characteristics = 85C) Electrical(TjCharacteristics (TJ = 85 C) 1600 Forward Current (mA) 1400 1200 1000 800 600 400 200 0 2.50 2.75 3.00 3.25 3.50 Forward Voltage (V) Relative Intensity vs. Current (Tj = 85C) Relative Luminous Flux vs. Current (TJ = 85 C) - White Relative Luminous Flux (%) 350% 300% 250% 200% 150% 100% 50% 0% 0 200 400 600 800 1000 1200 1400 1600 Forward Current (mA) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 6 Relative Radiant Flux vs. Current (Tj = 85C) xlamp XT-E LEDs Relative Radiant Flux vs. Current (TJ = 85 C) - Royal Blue Relative Radiant Flux (%) 350% 300% 250% 200% 150% 100% 50% 0% 0 200 400 600 800 1000 Forward Current (mA) 1200 1400 1600 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 7 xlamp XT-E LEDs Chromaticity Vs. Current, WW Relative Relative Chromaticity vs. Current and Temperature (Warm White) 0.020 TJ = 85 C 0.015 0.010 0.005 0.000 CCx CCy -0.005 -0.010 -0.015 -0.020 0 200 400 600 800 1000 Relative Chromaticity Vs. Temperature WW (mA) Current 1200 1400 1600 0.020 IF = 350 mA 0.015 0.010 0.005 0.000 CCx CCy -0.005 -0.010 -0.015 -0.020 0 20 40 60 80 Tsp (C) 100 120 140 160 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 8 xlamp XT-E LEDs Typical Spatial Radiation Pattern Typical Spatial Distribution - White Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -90 -70 -50 -30 -10 10 30 50 70 90 Angle () pical Spatial Distribution Typical Spatial Distribution - Royal Blue Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -90 -70 -50 -30 -10 10 30 50 70 90 Angle () Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 9 xlamp XT-E LEDs Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is Thermal Design crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1600 Maximum Current (mA) 1400 1200 1000 800 Rj-a Rj-a Rj-a Rj-a 600 400 = = = = 10C/W 15C/W 20C/W 25C/W 200 0 0 20 40 60 80 100 120 140 Ambient Temperature (C) Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 10 xlamp XT-E LEDs Reflow Soldering Characteristics In testing, Cree has found XLamp XT-E LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 Profile Feature t 25C to Peak Time Lead-Based Solder Lead-Free Solder 3 C/second max. 3 C/second max. Preheat: Temperature Min (Tsmin) 100 C 150 C Preheat: Temperature Max (Tsmax) 150 C 200 C 60-120 seconds 60-180 seconds 183 C 217 C 60-150 seconds 60-150 seconds 215 C 260 C 10-30 seconds 20-40 seconds 6 C/second max. 6 C/second max. 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5 C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 C to Peak Temperature Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 11 xlamp XT-E LEDs Notes Lumen Maintenance Projections Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document at www.cree.com/products/pdf/LM-80_Results.pdf. Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree's lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity In testing, Cree has found XLamp XT-E LEDs to have unlimited floor life in conditions 30 C/85% relative humidity (RH). Moisture testing included a 168-hour soak at 85 C/85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree also recommends returning any unused LEDS to the resealable moisture-barrier bag and closing the bag immediately fter use. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/ products/pdf/XLamp_EyeSafety.pdf. Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 12 3.30 xlamp XT-E LEDs .65 .650 1.30 R1.530 Mechanical Dimensions 6 1.15 5 4 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION 6 .60 CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT NOTICE 1.20 6 MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT .60 AND CONTAINED WITHIN ARENOTICE THE PROPRIETARY OF CREE INC. 3 5 4 All measurements are .13 mm unless otherwise 5 indicated. CONFIDENTIAL INFORMATION CREE, PLOT CREE CONFIDENTIAL. THISOF PLOT ANDINC. THETHIS INFORMATION MAY NOT BE COPIED, REPRODUCED OR DISCLOSED CONTAINED WITHIN ARE THE PROPRIETARY AND TO ANY UNAUTHORIZED PERSON WITHOUT WRITTEN CONSENT CONFIDENTIAL INFORMATION OFTHE CREE, INC. THIS PLOT OF MAY CREENOT INC.BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. D D .40 3.20 3.450 .40 REV R 2.36 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 3.450 .83 RECOMMENDED STENCIL PATTERN 3.450 (HATCHED AREA IS OPENING) THIRD ANGLE PROJECTION FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 5 4 2.30 DATE DRAWN BY D. CRONIN 2.36 3/8/11 CHECK -- 2.36 MATERIAL Fax (919) 313-5558 A 2.30 DATE .50-- TITLE .83 OUTLINE DRAWING XP HEW 1.15 -- .83 SIZE C FINAL PROTECTIVE FINISH 3 Phone (919) 313-5300 -- APPROVED -- 4600 Silicon Drive Durham, N.C 27703 1.15 DATE SURFACE FINISH: 1.6 C REV ANODE 3.20 MENDED PCB SOLDER PAD REMOVED CHIP DIMENSIONS 3 1.60 1.30 3.30 DESCRIPTION B .40 D B 4 REVISONS B REV 3 B 3.30 1.65 2 -- SCALE REV. 2610-00015 .50 2 B SHEET .50 24.000 2.30 1.15 DRAWING NO. OF 1 /1 1 3.450 3.30 C ANODE C 3.450 3.450 .65 .650 1.30 R1.530 Top View B .50 B.50 1.15 .60 1.60 .40 1.65 .40 3.30 1.65 3.30 .40 1.30 3.30 .50 3.30 5 RECOMMENDED PCB SOLDER PAD A 6 1.60 4 RECOMMENDED PCBSolder SOLDER PAD Recommended PCB Pad 3.20 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 1.60 RECOMMENDED STENCIL PATTERN .40 (HATCHED AREA IS OPENING) 1.30 .50 .40 .40 1.65 .40 3.20 .40 3.20 3.30 RECOMMENDED PCB SOLDER PAD .40 A .60 1.20 .60 3.20 1.20 .60 .50 .50 A 3.30 1.30 .50 1.30 1.30 .65 .50 .65 .60 1.15 .65 .65 .650 .60 1.20 R1.530 .50 .40 .650 R1.530 .65 B Bottom View Side View 1.15 .40 THIRD ANGLE PROJECTION 3.20.40 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 DATE DRAWN BY D. CRONIN CHECK 3/8/11 DATE -APPROVED -- -DATE TITLE -- OUTLINE D MATERIAL SIZE UNLESS--OTHERWISE SPECIFIED D. CRON FINAL PROTECTIVE FINISH 3.20 DIMENSIONS ARE IN DRAWN CHECK MILLIMETERS AFTER FINISH. UNLESSAND OTHERWISE SPECIFIED SCALE RECOMMENDED STENCIL PATTERN D. SURFACE FINISH: 1.6 --DIMENSIONS -- C TOLERANCE UNLESS SPECIFIED: ARE IN24.000 CHECK .XX .25 (HATCHED AREA IS OPENING) APPROVED MILLIMETERS AND AFTER FINISH. 3 2 RECOMMENDED STENCIL PATTERN .XXX UNLESS .125SPECIFIED: TOLERANCE -X .XX .5 .25 (HATCHED AREA IS OPENING) THIRD ANGLE PROJECTION APPROV .XXX PARTS .125 FOR SHEET METAL ONLY MATERIAL 1.5 .5 .X X THIRD ANGLE PROJECTION .XX METAL .75PARTS ONLY MATERI FOR SHEET .XXX.X .25 1.5 FINAL PROTECTI X .XX .5 .75 C DRAWN BY DRAWING Recommended Stencil Pattern (Shaded Area Is Open) 6 5 6 4 5 .XXX 1.6 SURFACE FINISH: X .25 .5 SURFACE FINISH: 1.6 3 4 3 Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 13 FINAL PRO xlamp XT-E LEDs 6 Tape and Reel 5 6 4 5 3 +.10 +.0039 4 2 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT REV MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. 3 1 REV BY DATE D 4.00 [.157] Po All dimensions in mm. 6 5 4 3 2 BY DESCRIPTION 1.50 +.10 +.0039 -.00[.0591-.0000]Do C 4.39 [.173] 5 4 NOTICE NTIAL. THIS PLOT AND THE INFORMATION HIN ARE THE PROPRIETARY AND NFORMATION OF CREE, INC. THIS PLOT PIED, REPRODUCED OR DISCLOSED TO ANY PERSON WITHOUTTHE WRITTEN CONSENT 8.00 [.315] P 5.50 [.217]F 4.39 [.173] C B 8.00 [.315] P 2 REVISONS +.10 4.39 [.173] +.0039 .0937 -.00[ -.0000] 12.00 [.472] NOMINAL 5.50 [.217]F REV 2.38 4.39 [.173] .30 [.012] T 1.50 [.059] D1 1 DESCRIPTION BY DATE ADDED CATHODE AND ANODE NOTE REORIENTED DEVICE DC 2/26/12 2.38 Ko C 7.3 APP'D +.10 -.00[ .0937 POCK A B 6 Ko START .10 POCKET SIZE 3 Ao - 5 4 6 Bo - 3.78mm [.149"] Ko - 2.38mm [.094"] 3 DRAWN BY DATE CHECK DATE APPROVED DATE -- 3 Phone (919) 313-5300 -- APPROVED A DATE -- TITLE -- 2CARRIER TAPE XP HEW MATERIAL -- 5 SIZE FINAL PROTECTIVE FINISH INDEX +.3 -.0 THIRD ANGLE PROJECTION Fax (919) 313-5558 QTY -- 12 2 2402-00018 4 SHEET DRAWING SCALE 1 2 2400-00009-CORE 2400-00009-REEL 1 2400-00009 OF 3.78m Ko - 2.38m UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH: 1.6 REV. DRAWING NO. C ITEM SCALE 3.78m Bo - ACOMMENTS 3 Fax (919) 313-5558 1 A TITLE D CARRIER TAPE XP HEW SIZE REV. DRAWING NO. C 2402-00018 SCALE SHEET DRAWING SCALE 2 A OF 1 /1 1 User Feed Direction B Carrier Tape C 12.4 +.2 .0 MEASURED AT HUB C Pocket Tape 330 +.25 -.75 16.4 +0.2 .0 MEASURED AT HUB 13mm 7" THIRD ANGLE PROJECTION B 6 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH: 5 4 3 1.9.4 21 .4 DATE DRAWN BY D. CRONIN 4600 Silicon Drive Durham, N.C 27703 11/29/10 CHECK DATE -- Phone (919) 313-5300 -- 13.1 .2 Fax (919) 313-5558 -- -- TITLE XP HEW LOADING SPEC -- SIZE FINAL PROTECTIVE FINISH 1.6 12.4 +1.0 -.5 MEASURED AT EDGE A DATE APPROVED MATERIAL -- SCALE 2402-00014 SHEET 3.000 2 B REV. DRAWING NO. C B OF 1 /1 1 60 60 REVISONS Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered REV BY DATE trademarks APP'D DESCRIPTION Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. UNLESS OTHERWISE SPECIFIED DRAWN BY A THIRD ANGLE PROJECTION DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .01 .XXX .005 X .5 D. CRONIN CHECK DATE 4600 Silicon Drive Durham, N.C 27703 09/29/09 DATE -APPROVED -MATERIAL Fax (919) 313-5558 DATE -- 14 Phone (919) 313-5300 -- DATE DRAWN BY D. CRONIN CHECK TITLE REEL, 13" X 12MM, 3 PIECE SNAP A 05/02/11 DATE -- -DATE APPROVED -- -- T MATERIAL -- SI FINAL PROTECTIVE FINISH -2 C 1 /1 Phone (919) 313-5300 -- FINAL PROTECTIVE FINISH 4 DATE Ao - 4600 Silicon Drive Durham, N.C 27703 05/02/11 -- 4600 Silicon Drive Durham, N.C 27703 05/02/11 -- SURFACE FINISH: 1.6 UNLESS OTHERWISE SPECIFIED D. CRONIN Leader DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. 400mm (min.) of -TOLERANCE UNLESS SPECIFIED: .XX .25 empty pockets .XXX .125 with -X .5 THIRD ANGLE PROJECTION at SHEET least FOR METAL100mm PARTS ONLY .X 1.5 sealed -.XX by.75tape .25 (50 empty .XXX pockets min.) X .5 SURFACE FINISH: 1.6 5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 3.78mm [.149"] 12.0 MATERIAL 6 TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 THIRD ANGLE PROJECTION 4 Loaded Pockets (1000 Lamps) DATE CHECK ANODE SIDE D B 4.1 UNLESS OTHERWISE SPECIFIED D. CRONIN DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. 2.5.1 1.75 DRAWN BY 5 Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) A 2.38mm [.094"] A CATHODE SIDE NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND 3.78 [.149] CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT 6 Ao MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. 3.78mm [.149"] Ko - 7.3 8.1 END 3.78mm [.149"] Bo - Ko D [.149] Ao .30 [.012] T +.10 +.0039 2.38 .0937 User Feed -.00[Direction-.0000] 1.5 .1 4.39 [.173] Ao3.78- 1.50 [.059] D1 3.78 [.149] Ao +.0039 -.0000] B POCKET SIZE 8.00 [.315] P 12.30 [.484] MAX W 10.25 [.404] E2 D B 12.30 [.484] MAX W B 7.3 10.25 [.404] E2 1.75 [.069] E1 C 3.78 [.149] Bo 1.50 [.059] 3 D1 12.00 [.472] NOMINAL -.00[.0591-.0000]Do 3.78 [.149] Bo APP'D 12.30 [.484] MAX W 10.25 [.404] E2 1.75 [.069] E1 DATE 12.00 [.472] NOMINAL 5.50 [.217]F 4.00 [.157]C Po 6 4.39 [.173] 1 REV 2.00 [.079] P2 D D REVISONS NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. +.10 +.0039 4.00 [.157] Po 1.75 [.069] E1 DESCRIPT APP'D 1.50 2.00 [.079] 1.50 -.00[.0591-.0000]Do 2.00 [.079] P2 All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. P2 D 2 REVISONS DESCRIPTION SC D Dessicant Desiccant xlamp XT-E LEDs (inside bag) (inside bag) Humidity Indicator Humidity Indicator Card (inside bag)bag) (inside Packaging Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label Bin with Cree Bin CREE Code & Barcode Label Code, Qty, Lot # Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Label with Customer P/N, Qty, Lot #, PO## Code, Qty, Lot Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Patent Label Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO# Label with Cree Bin Code, Qty, Lot # Copyright (c) 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks Copyright (c) 2011-2012 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered tradeof Cree, Inc. marks of Cree, Inc. 15