XTEAWT-00-0000-00000LDE3 - Cree, Inc.

CLD-DS41 REV 2

PRODUCT FAMILY DATA SHEET

Cree® XLamp® XT-E LEDs

WWW.CREE.COM/XLAMP

Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.

PRODUCT DESCRIPTION

XLamp XT-E is Cree’s highest

performing silicon carbide-based

LED technology, delivered in

Cree’s industry-standard XP/XT

packaging. XT-E White sets the

new standard for high performance

and dramatically lowers system

cost. XT-E Royal Blue is Cree’s

highest performing source of royal

blue light for remote-phosphor

applications.

Cree XLamp LEDs bring high

performance and quality of

light to a wide range of lighting

applications, including remote-

phosphor, color-changing, portable

and personal, outdoor, indoor-

directional, transportation, stage

and studio, commercial and

emergency-vehicle lighting.

FEATURES

• Available in white, 80-CRI min

white, 70-min CRI white and

royal blue

• Binned at 85 °C

• Coolwhiteefcacyofupto

148 lm/W (@ 85 °C, 350 mA)

• RoyalBluewallplugefciencyof

up to 53% (@ 85 °C, 350 mA)

• Wide viewing angle: 115-140°

• Thermal resistance: 5 °C/W

• Maximum drive current: 1.5 A

• Electrically neutral thermal path

• Vf binning supported for XT-E

White and Royal Blue

• XT-E Royal Blue sorted into 2.5-

nm wavelength bins

• Unlimitedoorlifeat

≤30ºC/85%RH

• Reowsolderable-JEDEC

J-STD-020CCompatible

• RoHS-andREACH-compliant

Cree, Inc.

4600 Silicon Drive

Durham, NC 27703

USA Tel: +1.919.313.5300

www.cree.com/xlamp

Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc.

Cree, Inc.

4600 Silicon Drive

Durham, NC 27703

USA Tel: +1.919.313.5300

TABLE OF CONTENTS

Product Characteristics ............... 2

Flux Characteristics .................... 2

Relative Spectral Power

Distribution .............................. 4

Relative Luminous Flux vs.

JunctionTemperature ................. 5

Electrical Characteristics ............. 6

Relative Luminous Flux vs.

Current .................................... 6

Relative Chromaticity vs. Current

and Temperature ....................... 8

Typical Spatial Distribution .......... 9

Thermal Design ........................10

ReowSolderingCharacteristics .11

Notes ......................................12

Mechanical Dimensions..............13

Tape and Reel ..........................14

Packaging ................................15

NOTE: For remote phosphor applications, a separate license to certain Cree patents is required.

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

PRODUCT CHARACTERISTICS

Characteristics Unit Minimum Typical Maximum

Thermal resistance, junction to solder point °C/W 5

Viewingangle(FWHM)-white degrees 115

Viewingangle(FWHM)-royalblue degrees 140

Temperaturecoefcientofvoltage mV/°C -2.5

ESDclassication(HBMperMil-Std-883D) Class 2

DC forward current mA 1500

Reverse voltage V 5

Forward voltage (@ 350 mA, 85 °C) V 2.85 3.4

LED junction temperature °C 150

FLUX CHARACTERISTICS - WHITE (TJ = 85 °C)

The following table provides several base order codes for XLamp XT-E White LEDs. It is important to note that the base

order codes listed here are a subset of the total available order codes for the product family. For more order codes, as

well as a complete description of the order-code nomenclature, please consult the XLamp XT-E Binning and Labeling

document.

Color

CCT Range

Base Order Codes

Minimum Luminous

Flux @ 350 mA (lm)

Calculated Minimum

Luminous Flux (lm)* Order Code

Min. Max. Group Flux (lm) 700 mA 1500 mA

Cool White 5,000 K 8,300 K

R3 122 217 369 XTEAWT-00-0000-000000F51

R4 130 231 393 XTEAWT-00-0000-000000G51

R5 139 247 420 XTEAWT-00-0000-000000H51

Outdoor White 4,000 K 6,200 K

R3 122 217 369 XTEAWT-00-0000-000000FE3

R4 130 231 393 XTEAWT-00-0000-000000GE3

R5 139 247 420 XTEAWT-00-0000-000000HE3

Neutral White 3,700 K 5,000 K

Q5 107 190 324 XTEAWT-00-0000-00000LFE4

R2 114 203 354 XTEAWT-00-0000-00000LEE4

R3 122 217 369 XTEAWT-00-0000-00000LDE3

70 CRI Minimum

Neutral White 3,700 K 5,000 K

Q5 107 190 324 XTEAWT-00-0000-00000BDF5

R2 114 203 354 XTEAWT-00-0000-00000BEF5

R3 122 217 369 XTEAWT-00-0000-00000BFF5

Notes:

• Creemaintainsatoleranceof±7%onuxandpowermeasurements,±0.005onchromaticity(CCx,CCy)measurementsand±2

on CRI measurements.

• Typical CRI for Neutral White, 3700 K - 5000K CCT is 75.

• Typical CRI for Warm White, 2600 K - 3700 K CCT is 80.

• Calculateduxvaluesareforreferenceonly

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

Color

CCT Range

Base Order Codes

Minimum Luminous

Flux @ 350 mA (lm)

Calculated Minimum

Luminous Flux (lm)* Order Code

Min. Max. Group Flux (lm) 700 mA 1500 mA

80 CRI Minimum

White 2,600 K 4,300 K

Q3 93.9 167 284 XTEAWT-00-0000-00000HBE7

Q4 100 178 302 XTEAWT-00-0000-00000HCE7

Q5 107 190 324 XTEAWT-00-0000-00000HDE7

Warm White 2,600 K 3,700 K

Q3 93.9 167 284 XTEAWT-00-0000-00000LBE7

Q4 100 178 302 XTEAWT-00-0000-00000LCE7

Q5 107 190 324 XTEAWT-00-0000-00000LDE7

70 CRI Minimum

Warm White 2,600 K 3,700 K

Q4 100 167 284 XTEAWT-00-0000-00000BCE7

Q5 107 178 302 XTEAWT-00-0000-00000BDE7

R2 114 190 324 XTEAWT-00-0000-00000BEE7

Notes:

• Creemaintainsatoleranceof±7%onuxandpowermeasurements,±0.005onchromaticity(CCx,CCy)measurementsand±2

on CRI measurements.

• Typical CRI for Neutral White, 3700 K - 5000K CCT is 75.

• Typical CRI for Warm White, 2600 K - 3700 K CCT is 80.

• Calculateduxvaluesareforreferenceonly

FLUX CHARACTERISTICS - ROYAL BLUE (TJ = 85 °C)

The following table provides order codes for XLamp XT-E Royal Blue LEDs. Additional information on the performance

grouping and codes for XT-E Royal Blue LEDs can be found in the XT-E Binning and Labeling document.

DWL

Kit

Codes

Dominant Wavelength Range

Order Codes, Minimum Radiant Flux @ 350 mA, Tj=85 °C

Min. Max.

Group DWL

(nm) Group DWL

(nm) 475 mW 500 mW 525 mW 550 mW

01 D36 450 D57 465 XTEARY-00-0000-000000K01 XTEARY-00-0000-000000L01 XTEARY-00-0000-000000M01 XTEARY-00-0000-000000N01

02 D36 450 D47 460 XTEARY-00-0000-000000K02 XTEARY-00-0000-000000L02 XTEARY-00-0000-000000M02 XTEARY-00-0000-000000N02

03 D46 455 D57 465 XTEARY-00-0000-000000K03 XTEARY-00-0000-000000L03 XTEARY-00-0000-000000M03 XTEARY-00-0000-000000N03

04 D36 450 D37 455 XTEARY-00-0000-000000K04 XTEARY-00-0000-000000L04 XTEARY-00-0000-000000M04 XTEARY-00-0000-000000N04

05 D46 455 D47 460 XTEARY-00-0000-000000K05 XTEARY-00-0000-000000L05 XTEARY-00-0000-000000M05 XTEARY-00-0000-000000N05

06 D56 460 D57 465 XTEARY-00-0000-000000K06 XTEARY-00-0000-000000L06 XTEARY-00-0000-000000M06 XTEARY-00-0000-000000N06

07 D37 452.5 D46 457.5 XTEARY-00-0000-000000K07 XTEARY-00-0000-000000L07 XTEARY-00-0000-000000M07 XTEARY-00-0000-000000N07

08 D47 457.5 D56 462.5 XTEARY-00-0000-000000K08 XTEARY-00-0000-000000L08 XTEARY-00-0000-000000M08 XTEARY-00-0000-000000N08

09 D37 452.5 D56 462.5 XTEARY-00-0000-000000K09 XTEARY-00-0000-000000L09 XTEARY-00-0000-000000M09 XTEARY-00-0000-000000N09

Note:

• Creemaintainsatoleranceof±7%onuxandpowermeasurements,±0.005onchromaticity(CCx,CCy)measurementsand±2

on CRI measurements.

FLUX CHARACTERISTICS - WHITE (TJ = 85 °C)

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

RELATIVE SPECTRAL POWER DISTRIBUTION - WHITE

RELATIVE SPECTRAL POWER DISTRIBUTION - ROYAL BLUE

Relative Spectral Power

100

400 450 500 550 600 650 700 750

Relative Radiant Power (%)

Wavelength (nm)

5000K - 8300K CCT

2600K -3700K CCT

Relative Spectral Power

20%

40%

60%

80%

100%

400 450 500 550 600 650 700 750

Relative Radiant Power (%)

Wavelength (nm)

Royal Blue

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

RELATIVE LUMINOUS FLUX VS. JUNCTION TEMPERATURE (IF = 350 mA) - WHITE

RELATIVE RADIANT FLUX VS. JUNCTION TEMPERATURE (IF = 350 mA) - ROYAL BLUE

Relative Flux Output vs. Junction Temperature

20%

40%

60%

80%

100%

120%

25 50 75 100 125 150

Relative Luminous Flux

Junction Temperature (ºC)

Relative Flux Output vs. Junction Temperature

20%

40%

60%

80%

100%

120%

25 50 75 100 125 150

Relative Radiant Flux

Junction Temperature (ºC)

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

ELECTRICAL CHARACTERISTICS (TJ = 85 °C)

RELATIVE LUMINOUS FLUX VS. CURRENT (TJ = 85 °C) - WHITE

Electrical Characteristics (Tj = 85ºC)

200

400

600

800

1000

1200

1400

1600

2.50 2.75 3.00 3.25 3.50

Forward Current (mA)

Forward Voltage (V)

Relative Intensity vs. Current (Tj = 85ºC)

50%

100%

150%

200%

250%

300%

350%

0200 400 600 800 1000 1200 1400 1600

Relative Luminous Flux (%)

Forward Current (mA)

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

RELATIVE RADIANT FLUX VS. CURRENT (TJ = 85 °C) - ROYAL BLUE

Relative Radiant Flux vs. Current (Tj = 85ºC)

50%

100%

150%

200%

250%

300%

350%

0200 400 600 800 1000 1200 1400 1600

Relative Radiant Flux (%)

Forward Current (mA)

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

RELATIVE CHROMATICITY VS. CURRENT AND TEMPERATURE (WARM WHITE)

Relative Chromaticity Vs. Current, WW

-0.020

-0.015

-0.010

-0.005

0.000

0.005

0.010

0.015

0.020

0200 400 600 800 1000 1200 1400 1600

Current (mA)

ΔCCx

ΔCCy

=85 °C

Relative Chromaticity Vs. Temperature WW

-0.020

-0.015

-0.010

-0.005

0.000

0.005

0.010

0.015

0.020

020 40 60 80 100 120 140 160

Tsp (°C)

ΔCCx

ΔCCy

IF=350 mA

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

TYPICAL SPATIAL DISTRIBUTION - WHITE

TYPICAL SPATIAL DISTRIBUTION - ROYAL BLUE

Typical Spatial Radiation Pattern

100

120

-90 -70 -50 -30 -10 10 30 50 70 90

Relative Luminous Intensity (%)

Angle (º)

Typical Spatial Distribution

100

120

-90 -70 -50 -30 -10 10 30 50 70 90

Relative Luminous Intensity (%)

Angle (º)

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

THERMAL DESIGN

The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is

crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to

ambient in order to optimize lamp life and optical characteristics.

Thermal Design

200

400

600

800

1000

1200

1400

1600

020 40 60 80 100 120 140

Maximum Current (mA)

Ambient Temperature (ºC)

Rj-a = 10°C/W

Rj-a = 15°C/W

Rj-a = 20°C/W

Rj-a = 25°C/W

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

REFLOW SOLDERING CHARACTERISTICS

Intesting,CreehasfoundXLampXT-ELEDstobecompatiblewithJEDECJ-STD-020C,usingtheparameterslisted

below.Asageneralguideline,Creerecommendsthatusersfollowtherecommendedsolderingproleprovidedbythe

manufacturer of solder paste used.

NotethatthisgeneralguidelinemaynotapplytoallPCBdesignsandcongurationsofreowsolderingequipment.

Prole Feature Lead-Based Solder Lead-Free Solder

Average Ramp-Up Rate (Tsmax to Tp) 3 °C/second max. 3 °C/second max.

Preheat: Temperature Min (Tsmin) 100 °C 150 °C

Preheat: Temperature Max (Tsmax) 150 °C 200 °C

Preheat: Time (tsmin to tsmax) 60-120 seconds 60-180 seconds

Time Maintained Above: Temperature (TL) 183 °C 217 °C

Time Maintained Above: Time (tL) 60-150 seconds 60-150 seconds

Peak/ClassicationTemperature(Tp) 215 °C 260 °C

Time Within 5 °C of Actual Peak Temperature (tp) 10-30 seconds 20-40 seconds

Ramp-Down Rate 6 °C/second max. 6 °C/second max.

Time 25 °C to Peak Temperature 6 minutes max. 8 minutes max.

Note: All temperatures refer to the topside of the package, measured on the package body surface.

Temperature

Time

t 25˚C to Peak

Preheat

Ramp-down

Ramp-up

Critical Zone

TL to TP

Tsmax

Tsmin

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

NOTES

Lumen Maintenance Projections

Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED

lumenmaintenance.ForinformationonthespecicLM-80datasetsavailableforthisLED,refertothepublicLM-80

results document at www.cree.com/products/pdf/LM-80_Results.pdf.

Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance

testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design,

ambient temperature, and drive current affect the LED junction temperature.

Moisture Sensitivity

Intesting,CreehasfoundXLampXT-ELEDstohaveunlimitedoorlifeinconditions≤30ºC/85%relativehumidity

(RH).Moisturetestingincludeda168-hoursoakat85ºC/85%RHfollowedby3reowcycles,withvisualandelectrical

inspections at each stage.

Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree

also recommends returning any unused LEDS to the resealable moisture-barrier bag and closing the bag immediately

fter use.

RoHSCompliance

The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or

otherwise restricted materials in this product are below the maximum concentration values (also referred to as the

threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive

2002/95/EContherestrictionoftheuseofcertainhazardoussubstancesinelectricalandelectronicequipment(RoHS),

as amended through April 21, 2006.

Vision Advisory Claim

WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/

products/pdf/XLamp_EyeSafety.pdf.

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

MECHANICAL DIMENSIONS

All measurements are ±.13 mm unless otherwise indicated.

Top View Bottom View

Side View

Recommended PCB Solder Pad Recommended Stencil Pattern

(Shaded Area Is Open)

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1.30

.65

.50

2.30

3.30

1.15

3.450

2.36

.83

.650

R1.530

.50

.40

1.30

3.30

1.15

.65

1.65

.50

1.20

.60

3.20

1.60

3.20

.40

1/124.000

2610-00015

OUTLINE DRAWING XP HEW

----

3/8/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

B REMOVED CHIP DIMENSIONS DC 5/11/11

RECOMMENDED PCB SOLDER PAD

RECOMMENDED STENCIL PATTERN

(HATCHED AREA IS OPENING)

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1.30

.65

.50

2.30

3.30

1.15

3.450

2.36

.83

.650

R1.530

.50

.40

1.30

3.30

1.15

.65

1.65

.50

1.20

.60

3.20

1.60

3.20

.40

1/124.000

2610-00015

OUTLINE DRAWING XP HEW

----

3/8/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

B REMOVED CHIP DIMENSIONS DC 5/11/11

RECOMMENDED PCB SOLDER PAD

RECOMMENDED STENCIL PATTERN

(HATCHED AREA IS OPENING)

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1.30

.65

.50

2.30

3.30

1.15

3.450

2.36

.83

.650

R1.530

.50

.40

1.30

3.30

1.15

.65

1.65

.50

1.20

.60

3.20

1.60

3.20

.40

1/124.000

2610-00015

OUTLINE DRAWING XP HEW

----

3/8/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

B REMOVED CHIP DIMENSIONS DC 5/11/11

RECOMMENDED PCB SOLDER PAD

RECOMMENDED STENCIL PATTERN

(HATCHED AREA IS OPENING)

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1.30

.65

.50

2.30

3.30

1.15

3.450

2.36

.83

.650

R1.530

.50

.40

1.30

3.30

1.15

.65

1.65

.50

1.20

.60

3.20

1.60

3.20

.40

1/124.000

2610-00015

OUTLINE DRAWING XP HEW

----

3/8/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

B REMOVED CHIP DIMENSIONS DC 5/11/11

RECOMMENDED PCB SOLDER PAD

RECOMMENDED STENCIL PATTERN

(HATCHED AREA IS OPENING)

ANODE

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

TAPE AND REEL

AllCreecarriertapesconformtoEIA-481D,AutomatedComponentHandlingSystemsStandard.

All dimensions in mm.

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

X° ± .5 °

.XXX ± .010

.XX ± .03

.X ± .06

FOR SHEET METAL PARTS ONLY

.XX ± .01

.XXX ± .005

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTANED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

SURFACE FINISH:

330

+.25

-.75

12.4

+1.0

-.5

MEASURED AT EDGE

16.4

+0.2

MEASURED AT HUB

12.4

+.2

MEASURED AT HUB

±.213.1

1.9±.4

±.421

60° 60°

1/10.500

2400-00009

REEL, 13" X 12MM, 3 PIECE SNAP

ANTI-STATIC HIPS

----

09/29/09D. CRONIN

2400-00009

INDEX QTY ITEM COMMENTS

1 1 2400-00009-CORE

2 2 2400-00009-REEL

REVISONS

REV DESCRIPTION BY DATE APP'D

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

Trailer

160mm (min) of

empty pockets

sealed with tape

(20 pockets min.)

Loaded Pockets

(1000 Lamps)

Leader

400mm (min.) of

empty pockets with

at least 100mm

sealed by tape

(50 empty pockets min.)

12.0

+.3

-.0

1.75

±.10

4±.1

8±.1 2.5±.1

1/13.000

2402-00014

XP HEW LOADING SPEC

----

11/29/10D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

ADDED CATHODE AND ANODE NOTE

REORIENTED DEVICE

DC 2/26/12

END START

User Feed Direction

CATHODE SIDE

ANODE SIDE

User Feed Direction

1.5± .1

13mm

Pocket Tape

Carrier Tape

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1/1DRAWING SCALE

2402-00018

CARRIER TAPE XP HEW

----

05/02/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

.30 [.012]

3.78 [.149]

+.10 +.0039

2.38 .0937 Ko

-.00[ -.0000]

3.78 [.149]

2.00 [.079]

4.00 [.157]

10.25

[.404]

1.50 +.10 +.0039 -.00[.0591-.0000]Do

4.39 [.173]

4.39

[.173]

7.3°

12.00 [.472]

NOMINAL

12.30 [.484]

MAX

1.75 [.069]

5.50 [.217]F

1.50 [.059]

8.00 [.315]

POCKET SIZE

Ao - 3.78mm [.149"]

Bo - 3.78mm [.149"]

Ko - 2.38mm [.094"]

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1/1DRAWING SCALE

2402-00018

CARRIER TAPE XP HEW

----

05/02/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

.30 [.012]

3.78 [.149]

+.10 +.0039

2.38 .0937 Ko

-.00[ -.0000]

3.78 [.149]

2.00 [.079]

4.00 [.157]

10.25

[.404]

1.50 +.10 +.0039 -.00[.0591-.0000]Do

4.39 [.173]

4.39

[.173]

7.3°

12.00 [.472]

NOMINAL

12.30 [.484]

MAX

1.75 [.069]

5.50 [.217]F

1.50 [.059]

8.00 [.315]

POCKET SIZE

Ao - 3.78mm [.149"]

Bo - 3.78mm [.149"]

Ko - 2.38mm [.094"]

SIZE

TITLE

REV.

SHEET

DRAWING NO.

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

123456

6 5 4 3 2 1

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUT

THE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X° ± .5 °

.XXX ± .25

.XX ± .75

.X ± 1.5

FOR SHEET METAL PARTS ONLY

.XX ± .25

.XXX ± .125

X° ± .5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH:

1.6

1/1DRAWING SCALE

2402-00018

CARRIER TAPE XP HEW

----

05/02/11D. CRONIN

REVISONS

REV DESCRIPTION BY DATE APP'D

.30 [.012]

3.78 [.149]

+.10 +.0039

2.38 .0937 Ko

-.00[ -.0000]

3.78 [.149]

2.00 [.079]

4.00 [.157]

10.25

[.404]

1.50 +.10 +.0039 -.00[.0591-.0000]Do

4.39 [.173]

4.39

[.173]

7.3°

12.00 [.472]

NOMINAL

12.30 [.484]

MAX

1.75 [.069]

5.50 [.217]F

1.50 [.059]

8.00 [.315]

POCKET SIZE

Ao - 3.78mm [.149"]

Bo - 3.78mm [.149"]

Ko - 2.38mm [.094"]

xlamp xT-E lEDs

of Cree, Inc.

marks of Cree, Inc.

PACKAGING

CREE Bin Code

& Barcode Label

Vacuum-Sealed

Moisture Barrier Bag

Label with Customer

P/N, Qty, Lot #, PO #

Desiccant

(inside bag)

Humidity Indicator

(inside bag)

Label with Cree Bin

Code, Qty, Lot #

Label with Cree Bin

Code, Qty, Lot #

Vacuum-Sealed

Moisture Barrier Bag

Dessicant

(inside bag)

Humidity Indicator

Card (inside bag)

Patent Label

Label with Customer Order

Code, Qty, Reel ID, PO #

Label with Customer Order Code,

Qty, Reel ID, PO#

Label with Cree Bin Code,

Qty, Lot #

CREE Bin Code

& Barcode Label

Vacuum-Sealed

Moisture Barrier Bag

Label with Customer

P/N, Qty, Lot #, PO #

Label with Cree Bin

Code, Qty, Lot #

Label with Cree Bin

Code, Qty, Lot #

Vacuum-Sealed

Moisture Barrier Bag

Patent Label

Label with Customer Order

Code, Qty, Reel ID, PO #