16-Bit, 80 MSPS A/D Converter AD10678 FEATURES FUNCTIONAL BLOCK DIAGRAM 80 MSPS sample rate 80 dBFS signal-to-noise ratio Transformer-coupled analog input Single PECL clock source Digital outputs True binary format 3.3 V and 5 V CMOS-compatible AIN AD10678 AIN DOUT0 14 DIGITAL POSTPROCESSING TE ADC APPLICATIONS 14 ADC 14 ANALOG POWER AGND 5VA 3.3VE AGND CLOCK DISTRIBUTION CIRCUIT DGND 3.3V DGND B SO The AD10678 is a 16-bit, high performance, analog-to-digital converter (ADC) for applications that demand increased SNR levels. Exceptional noise performance and a typical signal-tonoise ratio of 80 dBFS are obtained by digitally postprocessing the outputs of four ADCs. A single analog input and PECL sampling clock and 3.3 V and 5 V power supplies are required. DIGITAL POWER DRY 03376-A-001 ADC ENCODE ENCODE GENERAL DESCRIPTION OUTPUT DATA BITS DOUT15 LE Low signature radar Medical imaging Communications instrumentation Instrumentation Antenna array processing 14 ADC Figure 1. PRODUCT HIGHLIGHTS 1. 2. 3. Guaranteed sample rate of 80 MSPS. Input signal conditioning with optimized noise performance. Fully tested and guaranteed performance. O The AD10678 is assembled using a 0.062-inch laminate board with three sets of connector interface pads to accommodate analog and digital isolation. Analog Devices recommends using the FSI-110-03-G-D-AD-K-TR connector from Samtec. The overall board fits a 2.2 inch x 2.8 inch PCB specified from 0C to 70C. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved. AD10678 TABLE OF CONTENTS Test Circuits........................................................................................7 Applications....................................................................................... 1 Pin Configurations and Function Descriptions ............................8 General Description ......................................................................... 1 Typical Performance Characteristics ........................................... 10 Functional Block Diagram .............................................................. 1 Terminology .................................................................................... 12 Product Highlights ........................................................................... 1 Theory of Operation ...................................................................... 13 Table of Contents .............................................................................. 2 Thermal Considerations............................................................ 13 Revision History ........................................................................... 2 Input Stage................................................................................... 13 Specifications..................................................................................... 3 Encoding the AD10678 ............................................................. 13 DC Specifications ......................................................................... 3 Output Loading .......................................................................... 13 Digital Specifications ................................................................... 3 Analog and Digital Power Supplies.......................................... 13 AC Specifications.......................................................................... 4 Analog and Digital Grounding................................................. 14 LE TE Features .............................................................................................. 1 Other Notes................................................................................. 14 Absolute Maximum Ratings............................................................ 6 Evaluation Board ........................................................................ 14 Explanation of Test Levels ........................................................... 6 Outline Dimensions ....................................................................... 19 Operating Range........................................................................... 6 Ordering Guide .......................................................................... 19 B SO Switching Specifications .............................................................. 5 ESD Caution.................................................................................. 6 REVISION HISTORY 5/06--Rev. B to Rev. C Changes to Figure 9.......................................................................... 9 Edits to Table 8................................................................................ 15 Edits to Figure 22.......................................................................... 16 O 3/05--Rev. A to Rev. B Changes to Figure 1.......................................................................... 1 Changes to Figure 2 and Figure 3................................................... 7 Added Figure 7 to Figure 9.............................................................. 8 Reformatted Table 7 ......................................................................... 8 Changes to Figure 10........................................................................ 9 Reformatted Theory of Operation Section ................................. 13 Changes to Figure 22...................................................................... 15 12/03--Rev. 0 to Rev. A Updated format...................................................................Universal Changes to AC Specifications Table Footnotes ............................ 4 Changes to Table 1............................................................................ 3 Changes to Table 3............................................................................ 6 Changes to Figure 11...................................................................... 10 Changes to Theory of Operation.................................................. 13 Changes to Ordering Guide .......................................................... 20 2/03--Revision 0: Initial Version Rev. C | Page 2 of 20 Preliminary Technical Data AD10678 SPECIFICATIONS DC SPECIFICATIONS AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V, TA = 25C, differential encode = 80 MSPS, CLOAD 10 pF, unless otherwise noted. Table 1. 1 Min I I V V -0.30 -7 V V V 0.7 4 Unit Bits %FS %FS LSB LSB 13 200 60 ppm/C ppm/C dB 2.15 50 2.5 V p-p nF MHz Ratio 0.40 LE V V V IV V Typ 16 +0.12 Max +0.30 +7 TE Test Level 220 1.04:1 I I I I B SO Parameter RESOLUTION Offset Error Gain Error Differential Nonlinearity (DNL) Integral Nonlinearity (INL) TEMPERATURE DRIFT Offset Error Gain Error POWER SUPPLY REJECTION RATIO (PSRR) ANALOG INPUTS (AIN, AIN) 1 Differential Input Voltage Range Differential Input Resistance Differential Input Capacitance Input Bandwidth VSWR 2 POWER SUPPLY 3 Supply Current IAVCC (AVCC = 5.0 V) IEVCC (EVCC = 3.3 V) IVDD (VDD = 3.3 V) Total Power Dissipation 4 0.95 0.15 0.49 6.86 1.1 0.2 0.625 8.0 A A A W Measurement includes the recommended interface connector. Input VSWR, see Figure 18. Supply voltages should remain stable within 5% for normal operation. 4 Power dissipation measured with encode at rated speed and -6 dBFS analog input at 10 MHz. 2 3 DIGITAL SPECIFICATIONS AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V, TA = 25C, differential encode = 80 MSPS, CLOAD 10 pF, unless otherwise noted. Table 2. O Parameter ENCODE INPUTS (ENCODE, ENCODE) Differential Input Voltage Range Differential Input Resistance Differential Input Capacitance LOGIC OUTPUTS (D15 to D0) Logic Compatibility Logic 1 Voltage ILOAD 100 mA Logic 0 Voltage ILOAD 100 mA Output Coding Series Output Resistance per Bit Test Level Min IV V V 0.4 IV IV Rev. C | Page 3 of 20 Typ 100 160 CMOS 0.9 x VDD 0.4 True binary 120 Max Unit V p-p pF V V AD10678 AC SPECIFICATIONS AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V, TA = 25C, differential encode = 80 MSPS, CLOAD 10 pF, unless otherwise noted. Table 3. SFDR 3 Analog Input @ -6 dBFS Min Typ 2.5 MHz 10 MHz 30 MHz 70 MHz I I I I 77.5 77.5 77 76 80.5 80.5 80.2 78 dBFS dBFS dBFS dBFS 2.5 MHz 10 MHz 30 MHz 70 MHz I I I I 77.2 77.2 76.6 74.7 80.3 80.3 79.7 77.4 dBFS dBFS dBFS dBFS 2.5 MHz 10 MHz 30 MHz 70 MHz I I I I 88 88 84 81 97.2 97.2 94.2 91.7 dBFS dBFS dBFS dBFS TWO-TONE 4 Analog Input @ -7 dBFS IMD f1 = 10 MHz, f2 = 12 MHz f1 = 70 MHz, f2 = 72 MHz 1 Max TE SINAD 2 Analog Input @ -6 dBFS Test Level LE Parameter SNR 1 Analog Input @ -6 dBFS V V 96 84 Unit dBFS dBFS O B SO Analog input signal power at -6 dBFS; signal-to-noise (SNR) is the ratio of signal level to total noise (first five harmonics removed). Encode = 80 MSPS. SNR is reported in dBFS, related back to converter full scale. Analog input signal power at -6 dBFS; signal-to-noise and distortion (SINAD) is the ratio of signal level to total noise + harmonics. Encode = 80 MSPS. SINAD is reported in dBFS, related back to converter full scale. 3 Analog input signal equals -6 dBFS; SFDR is the ratio of the converter full scale to the worst spur. 4 Both input tones at -7 dBFS; two-tone intermodulation distortion (IMD) rejection is the ratio of either tone to the worst third-order intermodulation product. 2 Rev. C | Page 4 of 20 Preliminary Technical Data AD10678 SWITCHING SPECIFICATIONS AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V, TA = 25C, differential encode = 80 MSPS, CLOAD 10 pF, unless otherwise noted. Table 4. Duty cycle = 50%. Min 80 Typ Max 30 60 40 12.5 6.25 6.25 Unit MSPS MSPS % ns ns ns TE V V V V V V O B SO 1 Test Level I IV IV 6.7 7.3 ns ns 12.6 6.4 ns ns 10 1 480 500 10 ns ns ps fs rms Cycles LE Parameter MAXIMUM CONVERSION RATE MINIMUM CONVERSION RATE DUTY CYCLE ENCODE INPUTS PARAMETERS Encode Period @ 80 MSPS, tENC Encode Pulse Width High @ 80 MSPS, tENCH Encode Pulse Width Low @ 80 MSPS, tENCL ENCODE/DATA (D15:D0) Propagation Delay, tPDH Valid Time, tPDL ENCODE/DATA READY 1 Encode Rising to Data Ready Falling, tDR_F Encode Rising to Data Ready Rising, tDR_R DATA READY/DATA1 Data Ready to Data (Hold Time) tH_DR Data Ready to Data (Setup Time) tS_DR APERTURE DELAY, tA APERTURE UNCERTAINTY (JITTER), tJ PIPELINE DELAYS Rev. C | Page 5 of 20 AD10678 ABSOLUTE MAXIMUM RATINGS Rating 0 V to 7 V 0 V to 6 V -0.5 V to +3.8 V 0 V to AVCC 25 mA 0 V to 5 V -0.5 V to VDD 150C -65C to +150C 92C Table 6. Output Coding (True Binary) AIN (V) +1.1 . . . 0 -0.000034 . . . -1.1 ESD CAUTION Digital Output 1111 1111 1111 1111 . . . 1000 0000 0000 0000 0111 1111 1111 1111 . . . 0000 0000 0000 0000 EXPLANATION OF TEST LEVELS I. II. III. IV. V. 100% production tested. 100% production tested at 25C and sample tested at specified temperatures. Sample tested only. Parameter is guaranteed by design and characterization testing. Parameter is a typical value only. 100% production tested at 25C; guaranteed by design and characterization testing for industrial temperature range; 100% production tested at temperature extremes for military devices. OPERATING RANGE Operating ambient temperature range: 0C to 70C. See the Thermal Considerations section. B SO Code 65535 . . . 32768 32767 . . . 0 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. LE Parameter AVCC to AGND EVCC to AGND VDD to DGND Analog Input Voltage Analog Input Current Encode Input Voltage Digital Output Voltage Maximum Junction Temperature Storage Temperature Range Ambient Maximum Operating Temperature Ambient TE Table 5. O ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. C | Page 6 of 20 Preliminary Technical Data AD10678 TEST CIRCUITS tA N N+2 N+1 N+3 N+4 N+6 N+5 ENCODE, ENCODE tENCL N N+1 tENCH N+2 N+3 tPDH DATA BITS, D[15:0] N-10 tPDL N-9 N-8 DATA-READY OUTPUT N tH_DR N+5 N+6 N-7 N-6 N-5 tDR_R tDR_F LE tS_DR N+4 N+1 N+2 N+3 N+4 N+5 03376-A-002 tENC TE ANALOG INPUT N+6 Figure 2. Timing Diagram AVCC B SO VCH 1:1 AIN 25 200 BUF VCL BUF 500 VCH AIN 25 T/H 500 VREF AVCC 500 BUF T/H 03376-A-003 x4 VCL Figure 3. Analog Input Stage VDD VDD P 37.5k MACROCELL LOGIC 100 ENC PECL DRIVER 03376-A-004 ENC 120 N Figure 5. Digital Output Stage Figure 4. Equivalent Encode Input VDD VDD P MACROCELL LOGIC 1k Figure 6. Data-Ready Output Rev. C | Page 7 of 20 03376-A-023 DRY N D0-D15 03376-A-005 O EVCC AD10678 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS DGND 1 2 DGND DGND 1 2 DGND +3.3VE 1 2 +5.0VA DOUT15 3 4 NC +3.3VD 3 4 DOUT0 +3.3VE 3 4 +5.0VA DOUT14 5 6 DGND +3.3VD 5 6 DOUT1 AGND 5 6 +5.0VA DOUT13 7 8 NC +3.3VD 7 8 DOUT2 AGND 7 8 +5.0VA 10 DOUT3 TOP VIEW DGND 11 (Not to Scale) 12 DOUT4 DGND 13 14 DOUT5 AGND 9 18 DGND DGND 19 20 DRY NC = NO CONNECT Figure 7. Pin Configuration P1 (See Figure 22) Table 7. Pin Function Descriptions 2 3 DGND 15 16 DOUT6 ENCODE 15 16 AGND 18 DOUT7 ENCODE 17 18 AGND +3.3VD 19 20 DGND AGND 19 20 AGND Figure 8. Pin Configuration P2 (See Figure 22) P3 Pin No. 3 N/A N/A N/A N/A N/A 1, 3 2, 4, 6, 8 5, 7, 9 to 11, 13, 16, 18 to 20 12 14 15 17 Equivalent pin configuration in Figure 22 is J12. Equivalent pin configuration in Figure 22 is J11. Equivalent pin configuration in Figure 22 is J13. O 1 P2 Pin No. 2 1, 2, 9, 11, 13, 15, 20 4, 6, 8, 10, 12, 14, 16, 18 3, 5, 7, 17, 19 N/A N/A N/A N/A N/A N/A N/A N/A N/A 10 AGND TOP VIEW AGND 11 (Not to Scale) 12 AIN AGND 13 14 AIN +3.3VD 17 B SO P1 Pin No. 1 1, 2, 6, 10, 14, 18, 19 3, 5, 7, 9, 11, 13, 15, 17 N/A 4, 8, 12, 16 20 N/A N/A N/A N/A N/A N/A N/A AD10678 Figure 9. Pin Configuration P3 (See Figure 22) Rev. C | Page 8 of 20 Mnemonic DGND DOUTx +3.3 VD NC DRY +3.3 VE +5.0 VA AGND AIN AIN ENCODE ENCODE Description Digital Ground. Data Bit Output. Digital Voltage (VDD). No Connection. Data Ready Output. Encode Voltage (EVCC). Analog Voltage (AVCC). Analog Ground. Analog Input. Analog Input (Complement). Encode Input. Encode Input (Complement). 03376-A-028 16 NC DOUT8 17 AD10678 TE DOUT9 15 DGND 9 03376-A-027 10 DGND TOP VIEW DOUT11 11 (Not to Scale) 12 NC DOUT10 13 14 DGND LE AD10678 03376-A-026 DOUT12 9 Preliminary Technical Data AD10678 0.466 20 2 P1 MH4 19 1 0.960 0.888 2.148 P3 20 1 1.223 MH2 TE 19 0.433 2 0.925 1.693 0.805 0.900 MH1 LE 20 2 0.526 P2 MH3 19 1 INTERFACE NOTES: SUGGESTED INTERFACE MANUFACTURER: SAMTEC INTERFACE PART NUMBERS FOR P1-P3: FSI-110-03-G-D-AD-K-TR (20-PIN) HOLES 1-4 ACCOMMODATE 2-56 THREADED HARDWARE. USE FOUR 2-56 NUTS FOR SECURING THE PART TO INTERFACE PCB. MANUFACTURER: BUILDING FASTENERS PART NUMBER: HNSS256 DIGIKEY #: H723-ND ALL METAL HARDWARE TO BE TORQUED TO 1.0 INCH-POUND. CARE MUST BE TAKEN WHEN TIGHTENING HARDWARE ADJACENT TO SURFACE-MOUNTED COMPONENTS TO AVOID DAMAGE. TOLERANCES: 0.xxx = 5mils O Figure 10. Interface PCB Assembly, Top View (Dimensions Shown in Inches) Rev. C | Page 9 of 20 03376-C-006 0.757 B SO 0.955 AD10678 TYPICAL PERFORMANCE CHARACTERISTICS 0 0 ENCODE = 80MSPS AIN = 2.5MHz SNR = 80.79dBFS SFDR = 97.22dBFS -10 -20 -30 -30 -40 -40 -50 -50 -60 -60 dBFS -70 -80 -80 -90 -90 -100 -100 -110 -110 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 03376-A-007 0 -130 0 Figure. 11. Single-Tone at 2.5 MHz 10 15 20 25 FREQUENCY (MHz) 30 35 40 Figure 14. Single-Tone at 70 MHz 0 0 ENCODE = 80MSPS AIN = 10MHz SNR = 80.76dBFS SFDR = 94.81dBFS -10 LE -10 -20 -30 -20 ENCODE = 80MSPS AIN = 10.1MHz AND 12.1MHz IMD = 98.25dBFS -30 -40 -40 -50 -50 dBFS -60 -70 -60 -70 -80 -110 -120 -130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 -90 -100 -110 -120 -130 0 Figure 12. Single-Tone at 10 MHz O 10 15 20 25 FREQUENCY (MHz) 30 35 40 Figure 15. Two-Tone at 10.1 MHz and 12.1 MHz 0 ENCODE = 80MSPS -10 AIN = 32MHz -20 SNR = 80.18dBFS SFDR = 91.8dBFS -30 0 ENCODE = 80MSPS AIN = 70MHz AND 72MHz IMD = 87.5dBFS -10 -20 -30 -40 -50 -50 -60 -60 dBFS -40 -70 5 03376-A-011 -100 03376-A-008 -90 B SO -80 -80 -70 -80 -90 -90 -100 -100 -110 -110 -120 -120 -130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 03376-A-009 dBFS 5 03376-A-010 -120 -130 TE -120 dBFS -70 Figure 13. Single-Tone at 32 MHz -130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 Figure 16. Two-Tone at 70 MHz and 72 MHz Rev. C | Page 10 of 20 40 03376-A-012 dBFS -20 ENCODE = 80MSPS AIN = 70MHz SNR = 78.31dBFS SFDR = 87.64dBFS -10 Preliminary Technical Data AD10678 0 100 -0.30 SNR 2.5MHz SNR 10MHz 90 AIN = -1dB -0.60 80 -0.90 70 -1.20 60 SFDR 2.5MHz SFDR 30MHz -1.80 40 -2.10 30 -2.40 20 -2.70 10 15.9 30.8 45.7 60.6 75.5 90.4 105.3 120.2 135.1 150.0 FREQUENCY (MHz) Figure 17. Gain Flatness SNR 30MHz SFDR 10MHz 0 -80 -70 -60 -50 -40 -30 -20 FUNDAMENTAL LEVEL (dBFS) -10 0 TE -3.00 1.0 SNR 70MHz 50 03376-A-015 dBc -1.50 03376-A-013 dBFS SFDR 70MHz Figure 19. SFDR and SNR vs. Analog Input Level 2.0 100 1.9 1.8 LE 94 1.7 1.5 dBc VSWR 1.6 1.4 1.3 SFDR 88 1 10 FREQUENCY (MHz) 100 1k O Figure 18. Analog Input VSWR Rev. C | Page 11 of 20 76 0 10 20 30 40 50 60 ANALOG INPUT FREQUENCY (MHz) 70 Figure 20. SFDR and SNR vs. Analog Input Frequency 03376-A-024 1.0 0.1 SNR VSWR 03376-A-014 1.1 B SO 82 1.2 AD10678 TERMINOLOGY Analog Bandwidth The analog input frequency at which the spectral power of the fundamental frequency (as determined by the FFT analysis) is reduced by 3 dB. Output Propagation Delay The delay between the 50% point of the rising edge of the ENCODE command and the time when all output data bits are within valid logic levels. Aperture Delay The delay between the 50% point on the rising edge of the ENCODE command and the instant at which the analog input is sampled. Power Supply Rejection Ratio (PSRR) The ratio of a change in output offset voltage to a change in power supply voltage. Encode Pulse Width/Duty Cycle Pulse width high is the minimum amount of time that the encode pulse should be left in Logic 1 state to achieve rated performance; pulse width low is the minimum time that the encode pulse should be left in low state. At a given clock rate, these specifications define an acceptable encode duty cycle. Signal-to-Noise Ratio (SNR) The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, excluding the first five harmonics and dc. Can be reported in dBc (that is, degrades as signal level is lowered) or in dBFS (always related back to converter full scale). Integral Nonlinearity (INL) The deviation of the transfer function from a reference line measured in fractions of 1 LSB using a best straight line determined by a least square curve fit. Spurious-Free Dynamic Range (SFDR) The ratio of the rms signal amplitude to the rms value of the peak spurious spectral component. The peak spurious component may or may not be an harmonic. Can be reported in dBc (such as, degrades as signal level is lowered) or in dBFS (always related back to converter full scale). B SO LE TE Differential Nonlinearity (DNL) The deviation of any code from an ideal 1 LSB step. Signal-to-Noise and Distortion (SINAD) The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, including the first five harmonics and dc. Can be reported in dBc (that is, degrades as signal level is lowered) or in dBFS (always related back to converter full scale). Aperture Uncertainty (Jitter) The sample-to-sample variation in aperture delay. Harmonic Distortion The ratio of the rms signal amplitude to the rms value of the worst harmonic component. Minimum Conversion Rate The encode rate at which the SNR of the lowest analog signal frequency drops by no more than 3 dB below the guaranteed limit. Voltage Standing-Wave Ratio (VSWR) The ratio of the amplitude of the elective field at a voltage maximum to that at an adjacent voltage minimum. O Maximum Conversion Rate The encode rate at which parametric testing is performed. Two-Tone Intermodulation Distortion Rejection (IMD) Ratio of the rms value of either input tone to the rms value of the worst third-order intermodulation product; reported in dBc. Rev. C | Page 12 of 20 Preliminary Technical Data AD10678 THEORY OF OPERATION The analog input is designed for a 50 input impedance for easy interface to commercially available cables, filters, drivers, and so on. 65 60 55 50 45 40 30 0 50 100 150 200 AIR FLOW (AMBIENT) (LFM) 250 300 03376-A-025 35 Figure 21. Temperature (Case) vs. Air Flow (Ambient) INPUT STAGE The user is provided with a single-to-differential transformercoupled input. The input impedance is 50 and requires a 2.15 V p-p input level to achieve full scale. B SO LE The AD10678 encode inputs are ac-coupled to a PECL differential receiver/driver. The output of the receiver/driver provides a clock source for a 1:5 PECL clock driver and a PECLto-TTL translator. The 1:5 PECL clock driver provides the differential encode signal for each of the four high speed ADCs. The PECL-to-TTL translator provides a clock source for the complex programmable logic device (CPLD). 70 TE The four high speed ADCs use a three-stage subrange architecture. The AD10678 provides complementary analog input pins, AIN and AIN. Each analog input is centered around 2.4 V and should swing 0.55 V around the reference. Because AIN and AIN are 180 degrees out of phase, the differential analog input signal is 2.15 V p-p. 75 TEMPERATURE (CASE) (C) The AD10678 uses four parallel, high speed ADCs in a correlation technique to improve the dynamic range of the ADCs. The technique consists of summing the parallel outputs of the four converters to reduce the uncorrelated noise introduced by the individual converters. Signals processed through the high speed adder are correlated and summed coherently. Noise is not correlated and sums on an rms basis. The digital outputs from the four ADCs drive 120 series output terminators and are applied to the CPLD for postprocessing. The digital outputs are added together in the complex programmable logic device through a ripple-carry adder, which provides the 16-bit data output. The AD10678 provides valid data following 10 pipeline delays. The result is a 16-bit parallel digital CMOS-compatible word coded as true binary. THERMAL CONSIDERATIONS O Due to the high power nature of the part, it is critical that the following thermal conditions be met for the part to perform to data sheet specifications. This also ensures that the maximum junction temperature (150C) is not exceeded. ENCODING THE AD10678 The AD10678 encode signal must be a high quality, low phase noise source to prevent performance degradation. The clock input must be treated as an analog input signal because aperture jitter can affect dynamic performance. For optimum performance, the AD10678 must be clocked differentially. OUTPUT LOADING Take care when designing the data receivers for the AD10678. The complex, programmable logic device, 16-bit outputs drive 120 series resistors to limit the amount of current that can flow into the output stage. To minimize capacitive loading, there should be only one gate on each of the output pins. A typical CMOS gate combined with the PCB trace has a load of approximately 10 pF. Note that extra capacitive loading increases output timing and invalidates timing specifications. Digital output timing is guaranteed with a 10 pF load. ANALOG AND DIGITAL POWER SUPPLIES * Operation temperature (TA) must be within 0C to 70C. * All mounting standoffs should be fastened to the interface PCB assembly with 2-56 nuts. This ensures good thermal paths as well as excellent ground points. * The unit rises to ~72C (TC) on the heat sink in still air (0 linear feet per minute (LFM)). The minimum recommended air flow is 100 linear feet per minute (LFM) in either direction across the heat sink (see Figure 21). Care must be taken when selecting a power source. Linear supplies are recommended. Switching supplies tend to have radiated components that can be coupled into the ADCs. The AD10678 features separate analog and digital supply and ground currents, helping to minimize digital corruption of sensitive analog signals. Rev. C | Page 13 of 20 AD10678 The +3.3 VE supply provides power to the clock distribution circuit. The +3.3 VD supply provides power to the digital output section of the ADCs, the PECL-to-TTL translator, and the CPLD. Separate +3.3 VE and +3.3 VD supplies are used to prevent modulation of the clock signal with digital noise. next level assembly for optimum performance. The two standoffs located near P1 and P2 (MH3 and MH4) are tied to digital ground and should be connected accordingly on the next-level assembly. The +5.0 VA supply provides power to the analog sections of the ADCs. Decoupling capacitors are strategically placed throughout the circuit to provide low impedance noise shunts to ground. The +5.0 VA supply (analog power) should be decoupled to analog ground (AGND), and +3.3 VD (digital power) should be decoupled to digital ground (DGND). The +3.3 VE supply (analog power) should be decoupled to AGND. The evaluation board schematic and layout data provide a typical PCB implementation of the AD10678. Table 8 shows the PCB bill of materials. The circuit is configured on a 2.2 inch x 2.8 inch laminate board with three sets of connector interface pads. The pads are configured to provide easy keying for the user. The pads are made for low profile applications and have a total height of 0.12 inches after mating. The part numbers for the header mates are provided in Figure 10. All pins of the analog and digital sections are described in the Pin Configurations and Function Descriptions section. ANALOG AND DIGITAL GROUNDING The AD10678 evaluation board provides an easy way to test the 16-bit, 80 MSPS ADC. The board requires a clock source, an analog input signal, two 3.3 V power supplies, and a 5 V power supply. The clock source is buffered on the board to provide a latch, a data ready signal, and the clock for the AD10678. To use the AD10678 data ready output to clock the buffer memory, remove R24 (0.0 ) and install a 0.0 resistor at R31 (DNI). The ADC digital outputs are latched on board by a 74LCX16374. The digital outputs and output clock are available on a 40-pin connector, J1. Power is supplied to the board via uninsulated metal banana jacks. TE EVALUATION BOARD B SO LE Although the AD10678 provides separate analog and digital ground pins, the device should be treated as an analog component. Proper grounding is essential in high speed, high resolution systems. Multilayer printed circuit boards are recommended to provide optimal grounding and power distribution. The use of power and ground planes provides distinct advantages. Power and ground planes minimize the loop area encompassed by a signal and its return path, minimize the impedance associated with power and ground paths, and provide a distributed capacitor formed by the power plane, printed circuit board material, and ground plane. The AD10678 unit has four metal standoffs (see Figure 10). MH2 is located in the center of the unit and MH1 is located directly below analog header P3. Both of these standoffs are tied to analog ground and should be connected accordingly on the OTHER NOTES The analog input is connected via an SMA connector, AIN. The analog input section provides a single-ended input option or a differential input option. The board is shipped in a single-ended analog input option. Removing a ground tie at E17 converts the circuit to a differential analog input configuration. Table 8. PCB Bill of Materials Quantity 1 1 3 3 6 2 1 1 19 1 4 17 6 4 1 1 Reference Designator J1 U1 L1 to L3 J11 to J13 P1, P2, P8 to P10, P12 U5, U6 U7 R24 R0 to R16, R20, R23 R17 R18, R19, R21, R22 C1, C10 to C13, C16 to C18, C23 to C26, C28 to C32 C8, C9, C4, C15, C27, C33 J2, J3, J5, J6 A1 AD106xx Evaluation Board O Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description Connector, 40-position header, male straight IC, LV 16-bit, D-type flip-flop with 5 V tolerant I/O Common-mode surface-mount ferrite bead 20 Connector, 1 mm single-element interface Uninsulated banana jack, all metal IC, 3.3 V/5 V ECL differential receiver/driver IC, 3.3 V dual differential LVPECL to LVTTL translator RES 0.0 1/10 W 5% 0805 SMD RES 51.1 1/10 W 1% 0805 SMD RES 18.2 k 1/10 W 1% 0805 SMD RES 100 1/10 W 1% 0805 SMD CAP 0.1 F 16 V ceramic X7R 0805 CAP 10 F 10 V ceramic Y5V 1206 Connector, SMA jack 200 Mil STR gold Assembly, AD10678BWS GS04483 (PCB) Rev. C | Page 14 of 20 Figure 22. Evaluation Board Schematic C13 0.1F 16V C10 0.1F 16V 03376-A-016 AGND +5VA AGND +3.3VE L2 AGND AGND 2 4 C8 10F 10V 1 3 P2 P9 +5VA AGND +3.3VE AGND 2 4 R21 R22 100 100 C12 0.1F 16V R30 DNI C11 0.1F 16V AGND C15 10F 10V C25 0.1F 16V C26 0.1F 10V AGND AGND AGND MC10EL16D 8 7 6 5 AGND R19 100 C9 10F 10V 1 3 U6 NC VCC D Q D Q VBB VEE L1 1 2 3 4 +3.3VE AGND R18 100 P1 P10 8 7 6 5 +3.3VE MC10EL16D AGND NC VCC D Q D Q VBB VEE R17 18.2k 1 2 3 4 U5 POWER CONNECTIONS R20 51.1 J5 ENCODE R16 51.1 J6 ENCODE C32 0.1F 16V +3.3VE D0 VCC Q0 D0 Q1 D1 D1 GND 8 7 6 5 +3.3VD U7 AGND E17 R27 DNI AGND R24 0.0 R23 51.1 R31 DNI C18 0.1F 16V C29 0.1F 16V AGND E2 AGND E6 AGND E10 AGND E12 AGND E18 AGND E19 DGND DGND MH4 OPTIONAL EVALUATION BOARD GROUND TIES C16 0.1F 16V DGND DRY C17 0.1F 16V +3.3VD BUFMEM LATCH DGND BYPASS CAPACITORS DGND R28 DNI R29 DNI +3.3VD LE MH2 AGND AGND J3 J2 ANALOG INPUT E15 DGND AGND AGND DGND SINGLE-ENDED DIFFERENTIAL INPUT OPTION INPUT OPTION FSI-110-03-G-D-AD-TR 2 4 6 8 10 12 14 16 18 20 AGND C14 10F 10V 1 J13 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 18 17 20 19 MC100ELT23D DGND 1 2 3 4 B SO 1 3 5 7 9 11 13 15 17 19 C30 0.1F 16V AGND AGND E4 R30 DNI DGND LATCH DGND C33 10F 10V +3.3VD C28 0.1F 16V DGND E3 DGND E20 VCC VCC CP2 VCC OE2 VCC O15 I15 O14 I14 I13 O13 I12 O12 I11 O11 O10 I10 I9 O9 I8 O8 CP1 OE1 I7 O7 I6 O6 I5 O5 I4 O4 I3 O3 I2 O2 I1 O1 I0 O0 GND GND GND GND GND GND GND GND U1 DGND DGND E22 E13 DGND P12 DGND AGND P8 DGND E1 E5 L3 2 4 R25 DNI DGND E9 E7 DGND E11 DGND C27 10F 10V 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 40-PIN HMS 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 J1 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 C24 0.1F 16V DGND E8 C1 0.1F 16V +3.3VD R8 51.1 R9 51.1 R10 51.1 R11 51.1 R12 51.1 R13 51.1 R14 51.1 R15 51.1 +3.3VD R0 51.1 R1 51.1 R2 51.1 R3 51.1 R4 51.1 R5 51.1 R6 51.1 R7 51.1 DGND DGND 1 3 POWER CONNECTIONS +3.3VD 12 11 9 8 6 5 3 2 21 15 10 4 42 31 7 18 23 22 20 19 17 16 14 13 +3.3VD BUFMEM 74LCX16374MTD 25 24 26 27 29 30 32 33 35 36 48 1 37 38 40 41 43 44 46 47 28 34 39 45 C31 0.1F 16V TE AGND DGND +3.3VE C23 0.1F 16V E21 J8 O 2 4 6 8 10 12 14 Rev. C | Page 15 of 20 1 3 5 7 9 11 13 AGND DGND DRY +5VA MH3 J12 MH1-MH4 = DUT MOUNTING HOLES HEADER 732mm MH1 19 17 15 13 11 9 7 5 3 1 19 17 15 13 11 9 7 5 3 1 20 18 16 14 12 10 8 6 4 2 20 18 16 14 12 10 8 6 4 2 AD10678 PART OUTLINE SI-110-03-G-D-AD-TR J11 20 20 19 19 18 18 17 17 16 16 15 15 14 13 14 13 12 11 12 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 FSI-110-03-G-D-AD-TR DGND DGND 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 Preliminary Technical Data AD10678 AD10678 03376-A-017 LE TE AD10678/PCP EVALUATION BOARD 03376-A-018 O B SO Figure 23. Evaluation Board Mechanical Layout, Top View Figure 24. Evaluation Board Mechanical Layout, Bottom View Rev. C | Page 16 of 20 AD10678 03376-A-019 LE TE Preliminary Technical Data 03376-A-020 O B SO Figure 25. Evaluation Board Top Layer Copper Figure 26. Evaluation Board Second Layer Copper Rev. C | Page 17 of 20 03376-A-021 LE TE AD10678 03376-A-022 O B SO Figure 27. Evaluation Board Third Layer Copper Figure 28. Evaluation Board Bottom Layer Copper Rev. C | Page 18 of 20 Preliminary Technical Data AD10678 OUTLINE DIMENSIONS 2.795 0.170 0.120 0.070 2.745 R33 2.695 C3 C27 R30 C42 C37 R28 AD10678BWS LOT NUMBER DATA CODE USA TE R32 C35 R2 C60 C61 U6 R34 C32 R29 C44 C28 C31 R21 C45 R31 C26 C33 a C30 C24 C25 U5 U4 C34 R7 C62 C66 C64 C12 C47 C8 R25 R19 R18 U1 C13 R4 U7 C20 C18 R38 C43 C41 R5 C65 U8 C19 R3 R8 C63 R37 C5 C6 R11 C9 C7 R10 C48 R6 C46 C36 R13 MP4 R1 R9 T1 C38 C11 C67 C59 C10 C23 R35 R26 R40 C56 C55 P3 C21 R14 C40 U3 C49 C58 C57 R12 R16 C14 C52 C51 C4 C29 R27 C39 R39 C2 C22 C1 P2 MP5 C17 R41 MP3 2.220 2.170 2.120 U2 R17 R15 C15 C50 C54 C53 P1 MP6 0.370 0.320 LE 0.270 0.314 0.264 0.214 B SO Top View O Figure 29. AD10678 Outline Dimensions Dimensions shown in inches ORDERING GUIDE Model AD10678BWS AD10678/PCB Temperature Range 0C to 70C Package Description Non-Herm Hybrid Surface Mount (2.2" x 2.8") Evaluation Board Rev. C | Page 19 of 20 Package Option WS-120 AD10678 O B SO LE TE NOTES (c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03376-0-5/06(C) Rev. C | Page 20 of 20