Surface Mount Oven Stabilized Oscillator DOC Series Description: 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Connor-Winfield's high stability DOC OCXO / OCVCXO series are exceptionally precise frequency standards, excellent for use in cellular base stations, test equipment, Synchronous Ethernet and VSAT applications. These true surface mount OCXO / OCVCXO provide frequency stabilities in the range of 20 ppb to 100 ppb, over the commercial, extended commercial or the industrial temperature range. The DOC series is available with a CMOS output along with optional Electronic Frequency Tuning (OCVCXO). These oscillators provide outstanding phase noise characteristics that will meet the most stringent requirements. Package Outline 0.358 (9.1mm) OCXO / OCVCXO 3.3 Vdc Operation SMT Package Frequency Stabilities Available: 20 ppb, 50 ppb or 100 ppb Temperature Ranges Available: 0 to 70C, -20 to 75, -40 to 85C or -40 to 70C Low Phase Noise LVCMOS Output Optional Electronic Frequency Tuning RoHS Compliant / Lead Free 0.060 (1.52mm) 1028 DOC050F 10.0 MHZ 0.270 Max. (6.85mm) 0.040 (1.02mm) Bottom View Side View 0.375 (9.52mm) 0.085 (2.16mm) 0.060 (1.52mm) 4 0.100 (2.54mm) 0.100 (2.54mm) DNC 0.025 (0.64mm) 0.085 (2.16mm) DNC 0.275 (6.99mm) Top View Features: Suggested Pad Layout 1 0.555 (14.1mm) 1028 0F 05 DOC0.0MHZ 1 0.260 (6.60mm) 0.040 (1.02mm) 3 Top 5 View 2 6 1 DNC = Do Not Connect Keep Out Area Dimensional Tolerance: +/-0.005 (0.127mm) Pad Connections 1: N/C or Vc option 2: Do Not Connect 3 Ground: 4: Output 5: Do Not Connect 6: Supply Voltage (Vcc) Ordering Information Bulletin Page Revision Date Cx207 1 of 4 15 21 Aug 2012 DOC 05 Oscillator Type Frequency Stability 3.3 Vdc LVCMOS Output Surface Mount OCXO 02 = 20 ppb 05 = 50 ppb 10 = 100 ppb 25 = 250 ppb 0 F Temperature Range Voltage Control Option 0 = 0 to 70C 1 = -20 to 75C 2 = -40 to 85C 3 = -40 to 70C F = OCXO (Fixed Freq.) V = OCVCXO (Voltage Controlled) -010.0M Output Frequency Frequency Format -xxx.xM Min.* -xxx.xxxxxxM Max* *Amount of numbers after the decimal point. M = MHz Example Part Numbers: DOC050F-010.0M = 9x14mm package, 50 ppb, 0 to 70C, 3.3 Vdc, CMOS Output, OCXO, Output Frequency 10.0 MHz DOC022V-020.0M = 9x14mm package, 20 ppb, -40 to 85C, 3.3 Vdc, CMOS Output, OCVCXO, 20.0 MHz Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage - 3.3 Vdc (Vcc) Control Voltage (Vc) Minimum -55 -0.5 -0.5 Nominal - Maximum Units Notes Maximum Units Notes ppb ppb ppb 1 1 1 C C C C ppm ppb ppb ppb/day ppb ppm Vdc 2 5% 5% 3 3 4 5% 125 4.5 Vcc+0.5 C Vdc Vdc Operating Specifications Parameter Minimum Nominal Center Frequency: (Fo) 10, 12.8, 19.44, 20, 25, 38.88, 40, 50 or 80 Frequency Stability vs. Change in Temperature: (See Ordering Information) Stability Code 02 -20.0 20.0 Stability Code 05 -50.0 50.0 Stability Code 10 -100.0 100.0 Operating Temperature Range: (See Ordering Information) Temperature Code 0 0 70 Temperature Code 1 -20 75 Temperature Code 2 -40 85 Temperature Code 3 -40 70 Frequency Calibration: -1.0 1.0 Frequency Stability vs Load -20 20 Frequency Stability vs Voltage -20 20 Aging: Daily: -10 10 Aging: First Year: -300 300 Total Frequency Tolerance (20 Years) -4.60 4.60 Supply Voltage: (Vcc) 3.13 3.30 3.47 Power Consumption: Vcc = Nominal Voltage Commercial Temperature Range, 0 to 70 C Turn On 2.5 Steady State @ 25C 1.1 Industrial Temperature Range, -40 to 85 C Turn On 3.0 Steady State @ 25C 1.3 Phase Jitter: (BW: 12 KHz to Fo/2) 0.5 1.0 Short Term Stability 1.0E-9/s Start-Up Time: 10 Warm Up Time (Within Specification @ 25C) 60 Warm Up Time (Within Specification @ -40C) 90 MHz W W W W ps RMS ms s s CMOS Output Characteristics Parameter Load Output Voltage: 3.3 Vdc Models High (Voh) Low (Vol) Duty Cycle at 50% of Vcc Rise / Fall Time: 10% to 90% Minimum Nominal Maximum Units 2.70 45 - 50 - 0.30 55 6.5 V - 15 - pF 5 % ns Bulletin Page Revision Date Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Notes Cx207 2 of 4 15 21 Aug 2012 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Parameter @ 1 Hz offset @ 10 Hz offset @ 100 Hz offset @ 1 KHz offset @ 10 KHz offset @ 100 KHz offset Phase Noise Characteristics Typical Phase Noise for DOC050F - 010.0M Minimum - Nominal -67 -100 -130 -148 -154 -155 Maximum - dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz Units Notes Maximum Units Notes OCVCXO Input Characteristics (Optional) Parameter Control Voltage Range: Frequency Pullability: Input Impedance Linearity Minimum 0.30 10.0 100K 5 Nominal 1.65 - 3.00 - V ppm Ohms % 6 7 Package Characteristics Package Package consisting of a FR4 substrate and Ryton-R4 cover. Water Resistant, non-hermetic seal. Environmental Characteristics Shock 500 G's 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D. Sinusoidal Vibration 0.06" D.A. or 10G's Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A. Random Vibration 5.35 G's rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis. Moisture 10 cycles, 95% RH, Per MIL-STD-202G, Method 112. Marking Permanency Per MIL-STD-202G, Method 215J. Solder Process RoHS compliant, lead free. See solder profile on page 4. Recommended Cleaning Process DOC Series Package Wash only in a inline high pressure wash station that has an air knife and drying capabilities. (Drying temperature range from 85 to 100C) Notes: 1. Frequency stability vs. change in temperature. [(Fmax - Fmin)/2.Fo]. 2. Initial calibration @ 25C. For OCVCXO control voltage must be fixed. 3. After 30 days of operation 4. Inclusive of calibration @ 25C, frequency vs. change in temperature, change in supply voltage (5%), load change (5%), shock and vibration and 20 years aging 5. Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this OCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. 6. Positive slope. (Frequency increases as Vc voltage increases.) 7. Referenced to Fo. Bulletin Page Revision Date Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Cx207 3 of 4 15 21 Aug 2012 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com CMOS Output Waveform CMOS Test Circuit DNC Output 10uF to 100 uF 0.01uF 2 DNC Pad 1 OCXO = N/C OCVCXO = Vc 15 pF DNC = Do Not Connect Phase Noise Plot RoHS Solder Profile Typical phase noise plot for DOC050F-010.0M Temperature 260C 260C 220C 180C 150C 120C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Tape and Reel Information 1028 DOC050F 10.0 MHZ SM-MECH42 Bulletin Page Revision Date Specifications subject to change without notice. All dimensions in inches. (c) Copyright 2010 The Connor-Winfield Corporation Cx207 4 of 4 15 21 Aug 2012