KAOHSIUNG HITACHI ELECTRONICS CO.,LTD P.O. BOX 26-27 2,13TH EAST ST. K.E.P.Z. KAOHSIUNG TAIWAN R.O.C. TEL:(07) 821-5811(7 LINE) FAX:(07) 821-5815 DATE: Mar.06,2009 FOR MESSRS: CUSTOMER'S ACCEPTANCE SPECIFICATIONS SP14Q006-T CONTENTS No. ITEM SHEET No. PAGE 1 COVER 7B64PS 2701- SP14Q006-T-7 1-1/1 2 RECORD OF REVISION 7B64PS 2702- SP14Q006-T-7 2-1/2~2/2 3 GENERAL SPECIFICATION 7B64PS 2703- SP14Q006-T-7 3-1/1 4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704- SP14Q006-T-7 4-1/1 5 ELECTRICAL CHARACTERISTICS 7B64PS 2705- SP14Q006-T-7 5-1/2~2/2 6 OPTICAL CHARACTERISTICS 7B64PS 2706- SP14Q006-T-7 6-1/3~3/3 7 BLOCK DIAGRAM 7B64PS 2707- SP14Q006-T-7 7-1/1 8 INTERFACE TIMING CHART 7B64PS 2708- SP14Q006-T-7 8-1/3~3/3 9 OUTLINE DIMENSIONS 7B63PS 2709- SP14Q006-T-7 7B64PS 2709- SP14Q006-T-7 9-1/2 9-2/2 10 APPEARANCE STANDARD 7B64PS 2710- SP14Q006-T-7 10-1/3~3/3 11 PRECAUTION IN DESIGN 7B64PS 2711- SP14Q006-T-7 11-1/2~2/2 12 DESIGNATION OF LOT MARK 7B64PS 2712- SP14Q006-T-7 12-1/1 13 PRECAUTION FOR USE 7B64PS 2713- SP14Q006-T-7 13-1/1 When products will be discontinued , customers will be informed by HITACHI with twelve months prior announcement. ACCEPTED BY; KAOHSIUNG HITACHI ELECTRONICS CO.,LTD. PROPOSED BY; Sh. No. 7B64PS 2701- SP14Q006-T-7 PAGE 1-1/1 RECORD OF REVISION DATE SHEET No. SUMMARY Jan.16,'03 7B64PS 2705 - 5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT SP14Q006-T-2 PAGE 5 - 2/2 SYMBOL TYP. MAX VLED ILED (TBD) - 60 - Revised SYMBOL TYP. MAX VLED 5 5.2 ILED 160 - Oct.22,'03 7B64PS2709- Changed LED I/F SP14Q006-T-3 JAE/1L-G-4S-S3C2 JAE/IL-G-4S-S3C2 Page 9-2/2 Mar.24,'04 7B64PS2708- 8.3 POWER ON/OFF TIMING SEQUENCE SP14Q006-T-4 Revised tDLD min. 200 50 Page 8-3/3 Revised tCH max. 200 30 Jun.04,'04 7B64PS 2705- 5.1 ELECTRICAL CHARACTERISTICS Added SP14Q006-T-5 ITEM SYMBOL MIN. Page 5-1/2 Power Supply Voltage Logic Recommend LC Driving Voltage VDD-VSS VDD-V0 TYP. MAX 3.2 3.3 3.4 21.0 22.0 23.0 20.0 21.0 22.0 19.0 20.0 21.0 7B64PS 2706- 6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT SP14Q006-T-5 Added The LCD driving voltage should be adjusted at the voltage where the peak contrast is obtained. Page 6-3/3 7B64PS 2710SP14Q006-T-5 Page 10-1/3 May.04,'07 7B64PS 2703 - SP14Q006-T-6 Page 3-1/1 10.1 APPEARANCE INSPECTION CONDITION Revised 4525 3. GENERAL SPECIFICATIONS Added (11) Backlight Type LED(Color : white) (11) Backlight Type LED(Color : white) Life time : 40Kh @ 25 Note : Life time for half of initial brightness Sh. KAOHSIUNG HITACHI 7B64PS 2702- SP14Q006-T-7 PAGE 2-1/2 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. RECORD OF REVISION SUMMARY 7B64PS 2712 - SP14Q006-T-6 Page 12-1/1 Mar.06,'09 7B64PS 2712 SP14Q006-T-7 (mA/pcs) 5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT Revised allowable forward current DATE SHEET No. May.04,'07 7B64PS 2705 - SP14Q006-T-6 Page 5-2/2 Ambient Temperature() 12. DESIGNATION OF LOT MARK Added REVISION A 12. DESIGNATION OF LOT MARK Revised reversion from REV. A to REV.B PAGE 12-1/1 Sh. KAOHSIUNG HITACHI 7B64PS 2702- SP14Q006-T-7 PAGE 2-2/2 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 3. GENERAL SPECIFICATIONS (1) Part Name SP14Q006-T (2) Outer Dimensions 167.0(W)mmx109.0(H)mmx10.0 (D) mm max. (3) Effective Area 120(W)mm min. x 89(H)mm min. (4) Dot Size 0.345(W)min. x 0.345(H)min. (5) Dot Pitch 0.360(W)mm x 0.360(H)mm (6) Dot Number (Resolution) 320 (W) x 240 (H) dots (7) Duty Ratio 1/240 (8) LCD Type Transflective type F-B / W STN With anti-glare type upper polarizer (9) Viewing Direction (10) Viewing Angle 6 O'clock Viewing Angle in Rear (12:00) - Front (6:00) R-F=90 (typ.) (11) Backlight Type LED(Color : white) Life time : 40Kh @ 25 Note : Life time for half of initial brightness Sh. KAOHSIUNG HITACHI 7B64PS 2703- SP14Q006-T-7 PAGE 3-1/1 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 4. ABSOLUTE MAXIMUM RATINGS 4.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS ITEM SYMBOL MIN. Power Supply for Logic VDD-VSS 0 Power Supply for LC Driving VDD-VEE 0 Input Signal Voltage Vi -0.3 Static Electricity VESD0 VESD1 - VSS=0V : STANDARD MAX. UNIT COMMENT 6.0 V 27.5 V VDD+0.3 V (Note 1) 100 V (Note 2,3,4) 10 kV (Note 2,3,5) Note 1 : DOFF , FLM , CL1 , CL2 , D0~D3. Note 2 : Make certain you are grounded when handling LCM. Note 3 : Energy storage capacitance 200pF , discharge resistance 250 Ta=25 , 60%RH. Note 4 : Contact discharge to I/F connector pins. Note 5 : Contact discharge to front metal bezel. 4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS ITEM OPERATING STORAGE COMMENT MIN. MAX. MIN. MAX. -20 70 -30 80 Ambient Temperature (Note 2,3,6) Humidity (Note 1) (Note 1) Without Condensation 2 2 2.45m/s 11.76m/s Vibration (0.25G) (1.2G) (Note 4) Note 5 1h max. 2 29.4m/s 490.0m/s2 Shock (3 G) (50 G) XYZ Directions (Note 5) Corrosive Gas Note Acceptable Note Acceptable Note 1 : Ta40 : 85%RH max. Ta40 : Absolute humidity must be lower than the humidity of 85%RH at 40 Note 2 : Ta at -30 - - - 48h , at 80 - - - 168h. Note 3 : Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Note 4 : 5Hz~100Hz (Except resonance frequency) Note 5 : This module should be operated normally after finish the test. Note 6 : The response time will be slower under low temperature. Sh. KAOHSIUNG HITACHI 7B64PS 2704- SP14Q006-T-7 PAGE 4-1/1 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 5. ELECTRICAL CHARACTERISTICS 5.1 ELECTRICAL CHARACTERISTICS I T E M SYMBOL CONDITION Power Supply Voltage for Logic VDD-VSS - Power Supply Voltage for LC Driving VEE-VSS - Input Signal Voltage Power Supply Current for Logic Power Supply Current for LC Driving Vi IDD IEE Recommended LC Driving Voltage VDD-V0 Frame Frequency fFLM MIN. TYP. MAX. 4.75 5.0 5.25 3.2 3.3 3.4 -23.1 -22.0 -20.9 UNIT COMMENT V V H LEVEL 0.8VDD VDD V L LEVEL 0 0.2VDD V VDD-VSS=5.0V 6.0 mA VEE-VSS= -22.0V VDD-VSS=5.0V 5.0 mA VEE-VSS= -22.0V Ta= 0 , = 0 21.0 22.0 23.0 V Ta=25 , = 0 20.0 21.0 22.0 V Ta=50 , = 0 19.0 20.0 21.0 V 70 75 80 Hz (Note1) (Note2) (Note2) (Note3) (Note4) Note 1 : DOFF , FLM , CL1 , CL2 , D0~D3. Note 2 : FLM=75Hz , test pattern is all "Q". VDD-V0=21.0V , Ta=25 Note 3 : Recommended LC driving voltage may fluctuate about 1.0V by each module. Test pattern is all "Q" Note 4 : Please set the frame frequency so as to avoid flicker and rippling on the display. Sh. KAOHSIUNG HITACHI 7B64PS 2705- SP14Q006-T-7 PAGE 5-1/2 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 5.2 ELECTRICAL CHARACTERISTICS OF LED BACKLIGHT ITEM Power Supply Voltage for LED Power Supply Current for LED SYMBOL CONDITION MIN. TYP. MAX. UNIT VLED - - 5.0 5.2 V ILED VLED=5.0V - 160 - mA COMMENT (Note 1) (mA/pcs) allowable forward current Note 1 : The ILED changes depending on ambient temperature. Ambient Temperature() Sh. KAOHSIUNG HITACHI 7B64PS 2705- SP14Q006-T-7 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. PAGE 5-2/2 6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT I T E M MIN. TYP. MAX. UNIT (Backlight ON) NOTE Brightness - 60 - cd/m2 ILED=160mA Brightness Uniformity - - 30 % (Note 1) Ta=25, Display data should be all "ON". The LCD driving voltage should be adjusted at the voltage where the peak contrast is obtained. Note 1 : Measure of the following 9 places on the display. Y=80 Y=160 Y=240 X=60 X=120 X=180 Definition of the brightness tolerance. ( Max. or Min. Brightness-Average Brightness Average Brightness ) x 100 Sh. KAOHSIUNG HITACHI 7B64PS 2706- SP14Q006-T-7 PAGE 6-3/3 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. VLED(-) VLED(+) VEE LED Back Light POWER SUPPLY VSS V0 VDD IC7 X240 320x240 DOTS : TIMING CIRCUIT X240 D2 D1 D0 Y81 X161 D3 IC2 Y160 X160 X81 X80 X1 Y1 IC6 IC5 X1 IC1 Y80 DOFF CL1 FLM CL2 D0~D3 IC4 7. BLOCK DIAGRAM Y320 Y241 Sh. KAOHSIUNG HITACHI 7B64PS 2707- SP14Q006-T-7 PAGE 7-1/1 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 8. INTERFACE TIMING CHART 8.1 INTERFACE TIMING CHART 52.1sT59.5s CL1 CL2 X1 X240 X2 D3 Y1 Y5 Y317 D2 Y2 Y6 Y318 D1 Y3 Y7 Y319 D0 Y4 Y8 Y320 FLM CL1 240xT FLM D0~D3 X1 X2 X239 X240 Sh. KAOHSIUNG HITACHI 7B64PS 2708- SP14Q006-T-7 PAGE 8-1/3 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 8.2 TIMING CHARACTERISTICS ITEM SYMBOL fCP tw tr,tf tDSU tDHD tLSU tLC tSETUP tHOLD twc CL2 frequency CL2 pulse width CL2 rise, fall time Data set up time Data hold time CL1 set up time CL1 clock time "FLM" set up time "FLM" hold time "CL1" pulse width MIN. 45 30 30 80 120 100 100 125 tw tw 0.8VDD D0~D3 0.8VDD 0.2VDD 0.2VDD tDSU tDHD 0.8VDD 0.8VDD 0.8VDD 0.8VDD 0.2VDD 0.2VDD 0.2VDD 0.2VDD tLSU 0.8VDD CL1 UNIT MHz ns ns ns ns ns ns ns ns ns tr 0.8VDD 0.2VDD MAX. 6.5 15 - tw tf CL2 TYP. - 0.8VDD 0.2VDD tLC 0.8VDD 0.2VDD 0.2VDD twc tHOLD tSETUP 0.8VDD 0.8VDD FLM Sh. KAOHSIUNG HITACHI 7B64PS 2708- SP14Q006-T-7 PAGE 8-2/3 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 8.3 POWER ON/OFF TIMING SEQUENCE tDLD VDD tDLD 0.95VDD 0.95VDD tCH tCH GND 0.8VDD 0.8VDD tDLCr tDLCf SIGNAL GND VEE GND tDLCs tDLCs 0.8VDD DOFF 0.2VDD GND 0.8VDD 0.2VDD tLDH tLDH tDOr tDOf SYMBOL MIN. MAX. UNIT COMMENT tDLD 50 ms tCH 0 30 ms (Note 1) tLDH 0 ms tDOr 100 ns tDOf 100 ns tDLCr 0 ms (Note 2) tDLCf 0 ms tDLCs 20 ms Note 1 : Please keep the specified sequence because wrong sequence may cause permanent damage to the LCD panel. Note 2 : HITACHI recommends you to use DOFF function. Display quality may deteriorate if you don`t use DOFF function. 8.4 POWER SUPPLY FOR LCM (EXAMPLE) VDD LCM +5.0V VSS V0 VEE VR -22.0V Note 1 : VR : 10k Sh. KAOHSIUNG HITACHI 7B64PS 2708- SP14Q006-T-7 PAGE 8-3/3 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 115.185 (320 dots) 0.345 0.36 86.385 (240 dots) 9.2 DISPLAY PATTERN Scale : NTS Unit : mm Measurement Tolerance : 0.1 0.345 0.36 9.3 INTERFACE PIN CONNECTION FPCpitch 1.25mm 14 pins INTERFACE LCM CN1 INTERFACE LCM CN2 PIN No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 SIGNAL D0 D1 D2 D3 DOFF FLM N.C CL1 CL2 VDD VSS VEE V0 VSS LEVEL H/L Display Data PIN No. 1 2 3 4 SIGNAL VLED(+) N.C N.C VLED(-) LEVEL FUNCTION Power Supply for LED LED GND H/L H HL HL - FUNCTION H : ON / L : OFF First Line Marker Data Latch Data Shift Power Supply for Logic GND Power Supply for LC Operating Voltage LC Driving GND LED I/F : J.A.E / IL - G - 4S - S3C2-SA Sh. KAOHSIUNG HITACHI 7B64PS 2709- SP14Q006-T-7 PAGE 9-2/2 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 10. APPEARANCE STANDARD 10.1 APPEARANCE INSPECTION CONDITION Visual inspection should be done under the following condition. (1) The inspection should be done under in the dark room. (2) The CFL should be lighted with the prescribed inverter. (3) The distance between eyes of an inspector and the LCD module is 25cm. (4) The viewing zone is shown the figure . Viewing angle 25 eye eye 25 25 LCD Bezel 10.2 DEFINITION OF EACH ZONE A zone : Within the effective area specified at page 9-1/2 of this document. B zone : Area between the window of metal frame and the effective area line specified at page 9-1/2 of this document. Effective Area Window of Metal Frame A zone B zone Sh. KAOHSIUNG HITACHI 7B64PS 2710- SP14Q006-T-7 PAGE 10-1/3 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 10.3 APPEARANCE SPECIFICATION *) If a problem occurs in respect to any of these items , both parties(Customer and HITACHI) will discuss in more detail. No. ITEM CRITERIA Scratches Distinguished one is not acceptable (To be judged by HITACHI limit sample) Dent Same as Above Wrinkles in Polarizer Same as Above Bubbles Average Diameter Maximum Number D(mm) Acceptable D0.2 Ignore 0.2D0.3 12 0.3D0.5 3 0.5D None Stains, Filamentous Foreign Materials, Length Width Maximum Number Dark Spot L(mm) W(mm) Acceptable L2.0 W0.03 Ignore L3.0 0.03W0.05 6 L2.5 0.05W0.1 1 L Round Average Maximum Number Minimum Diameter Acceptable Space D(mm) C D0.2 Ignore 0.2 D0.33 8 10mm 0.33D None D Total Filamentous + Round = 10 Those wiped out easily are acceptable Color Tone To be judged by HITACHI limit sample Color Uniformity Same as above Pinhole Average Diameter Maximum Number D(mm) Acceptable D0.15 Ignore 0.15D0.3 10 C0.015 Ignore Contrast Average Contrast Maximum Minimum Irregularity Diameter Number Space (Spot) D(mm) Acceptable D0.25 To be Ignore 0.25D0.35 judged by 10 20mm 0.35D0.5 HITACHI 4 20mm 0.5 D None - A B - - - - - - - Sh. KAOHSIUNG HITACHI 7B64PS 2710- SP14Q006-T-7 PAGE 10-2/3 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 11. PRECAUTION IN DESIGN 11.1 LC DRIVING VOLTAGE (VEE) AND VIEWING ANGLE RANGE Setting VEE out of the recommended condition will be a cause for a change of viewing angle range. 11.2 PRECAUTIONS AGAINST STATIC CHARGE As this module contains C-MOS LSIs , it is not strong against electrostatic discharge. Make certain that the operator's body is connected to the ground through a list band etc. And don't touch I/F pins directly. 11.3 POWER ON SEQUENCE Input signals should not be applied to LCD module before power supply voltage is applied and reaches to specified voltage (VDD). If above sequence is not kept, C-MOS LSIs of LCD modules may be damaged due to latch up problem. 11.4 PACKAGING (1) No leaving product is preferable in the place of high humidity for a long period of time. For their storage in the place where temperature is 35 or higher ,special care to prevent them from high humidity is required. A combination of high temperature and high humidity may cause them polarization degradation as well as bubble generation and polarizer peel-off. Please keep the temperature and humidity within the specified range for use and storage. (2) Since polarizers tend to be easily damaged, They should be handled full with care so as not to get them touched, pushed or rubbed. (3) As the adhesives used for adhering polarizers are made of organic substances which will be deteriorated by a chemical reaction with such chemicals as acetone, toluene , ethanol and isopropyl alcohol. The following solvents are recommended for use: normal hexane Please contact us when it is necessary for you to use chemicals. (4) Lightly wipe to clean the dirty surface with absorbent cotton waste or other soft material like chamois , soaked in the chemicals recommended without scrubbing it hardly. To prevent the display surface from damage and keep the appearance in good state, it is sufficient, in general, to wipe it with absorbent cotton. (5) Immediately wipe off saliva or water drop attached on the display area because its long period adherence may cause deformation or faded color on the spot. (6) Foggy dew deposited on the surface due to coldness will be caused for polarizer damage, stain and dirt on product. When necessary to take out the products from some place at low temperature for test, etc. It is required for them to be warmed up in a container once at the temperature higher than that of room. (7) Touching the display area and contact terminals with bare hands and contaminating them are prohibited, because the stain on the display area and poor insulation between terminals are often caused by being touched by bare hands. (Some cosmetics are detrimental to polarizers.) Sh. KAOHSIUNG HITACHI 7B64PS 2711- SP14Q006-T-7 PAGE 11-1/2 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. (8) In general the quality of glass is fragile so that it tends to be cracked or chipped in handling, specially on its periphery. Be careful not to give it sharp shock caused by dropping down, etc. 11.5 CAUTION FOR OPAERATION (1) It is an indispensable condition to drive LCDs within the specified voltage limit since the higher voltage than the limit causes the shorter LCD life. An electrochemical reaction due to direct current causes LCDs undesirable deterioration , so that the use of direct current driver should be avoided. (2) Response time will be extremely delayed at lower temperature than the operating temperature range and on the other hand at higher temperature LCDs show dark blue color in them. However those phenomena do not mean malfunction or out of order with LCDs which will come back in the specified operating temperature range. (3) If the display area is pushed hard during operation, some font will be abnormally displayed but it resumes normal condition after turning off once. (4) A slight dew depositing on terminals is a cause for electrochemical reaction resulting in terminal open circuit. Please operate the LCD module under the relative condition of 40 85%RH. 11.6 STORAGE In case of storing for a long period of time (for instance , for years) for the purpose of replacement use , the following ways area recommended. (1) Storage in a polyethylene bag with the opening sealed , so the fresh air will not be entered from outside . (2) Placing in a dark place where neither exposure to direct sunlight nor light is , keeping temperature in the range from 0 to 35 . (3) Storing with no touch on polarizer surface by anything else. (It is recommended to store them as they have been contained in the inner container at the time of delivery from us.) 11.7 SAFETY (1) It is recommendable to crash damaged or unnecessary LCDs into pieces and wash off liquid crystal by either of solvents such as acetone and ethanol , which should be burned up later. (2) When any liquid leaked out of a damaged glass cell comes in contact with your hands , please wash it off well with soap and water. Sh. KAOHSIUNG HITACHI 7B64PS 2711- SP14Q006-T-7 PAGE 11-2/2 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 12. DESIGNATION OF LOT MARK 12.1 LOT MARK Lot mark is consisted of 5 digits for production lot and 6 digits for production control. 8 0 4 1 Year Figure in lot mark 2009 9 2010 0 2011 1 Week 2012 2 Month 2013 3 T Digits for production control T : Made in Taiwan Year Month Figure in lot mark Month Figure in lot mark Week (day in calendar) Figure in lot mark Jan. 01 Jul. 07 1~ 7 1 Feb. 02 Aug. 08 8~14 2 Mar. 03 Sep. 09 15~21 3 Apr. 04 Oct. 10 22~28 4 May 05 Nov. 11 29~31 5 Jun. 06 Dec. 12 12.2 SERIAL No. Serial No. is consisted of 6 digits number (000001~999999). 12.3 LOCATION OF LOT MARK Label is bring attached on the back side of module. 12.4 REVISION(Rev.) CONTROL Rev No. A B ITEM Mcount IC :MN73099HED(Panasonic) Transistor :2SA1036K(ROHM) Mcount IC :IT7001M(ITE) Transistor :2SA1576(ROHM) SP14Q006-T B Sh. KAOHSIUNG HITACHI 7B64PS 2712- SP14Q006-T-7 PAGE 12-1/1 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD. 13. PRECAUTION FOR USE 13.1 A limit sample should be provided by the both parties on an occasion when the both parties agreed its necessity. Judgment by a limit sample shall take effect after the limit sample has been established and confirmed by the both parties. 13.2 On the following occasions, the handling of the problem should be decided through discussion and agreement between responsible persons of the both parties. (1) When a question is arisen in the specifications. (2) When a new problem is arisen which is not specified in this specifications. (3) When an inspection specifications change or operating condition change in customer is reported to HITACHI, and some problem is arisen in this specification due to the change. (4) When a new problem is arisen at the customer's operating set for sample evaluation in the customer site. The precaution that should be observed when handling LCM have been explained above. If any points are unclear or if you have any request , please contact HITACHI. Sh. KAOHSIUNG HITACHI 7B64PS 2713- SP14Q006-T-7 PAGE 13-1/1 DATE Mar.06,'09 No. ELECTRONICS CO.,LTD.