Features * Industry-standard Architecture * * * * * * * * * * * - Low-cost, Easy-to-use Software Tools High-speed, Electrically Erasable Programmable Logic Devices - 5ns Maximum Pin-to-pin Delay Latch Feature Holds Inputs to Previous Logic States Pin-controlled Standby Power (10A Typical) Advanced Flash Technology - Reprogrammable - 100% Tested High-reliability CMOS Process - 20-year Data Retention - 100 Erase/Write Cycles - 2,000V ESD Protection - 200mA Latch-up Immunity Dual Inline and Surface Mount Packages in Standard Pinouts PCI-compliant Green Package Options (Pb/Halide-free/RoHS Compliant) Available Full Military, Commercial and Industrial Temperature Ranges Backward-Compatible with Atmel ATF22V10B(Q) and Atmel AT22V10(L) Applications Include Glue Logic for 5.0V Systems, DMA Control, State Machine Control, Graphics Processing 1. Description (R) The Atmel ATF22V10C is a high-performance CMOS (electrically erasable) programmable logic device (PLD) that utilizes proven electrically erasable Flash memory technology from Atmel. Speeds down to 5ns and power dissipation as low as 10A (typical) are offered. All speed ranges are specified over the full 5V 10% range for military and industrial temperature ranges, and 5V 5% for commercial temperature ranges. High-performance Electrically Erasable Programmable Logic Device Atmel ATF22V10C Atmel ATF22V10CQ See separate datasheet for the Atmel ATF22V10C(Q)Z Several low-power options allow selection of the best solution for various types of power-limited applications. Each of these options significantly reduces total system power and enhances system reliability. 0735U-PLD-7/10 Figure 1-1. 2. Logic Diagram Pin Configurations Table 2-1. Pin Configurations (All Pinouts Top View) Pin Name Function CLK Clock IN Logic Inputs I/O Bi-directional Buffers GND Ground VCC +5V Supply PD Power-down Figure 2-1. TSSOP CLK/IN IN IN IN/PD IN IN IN IN IN IN IN GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O IN DIP/SOIC CLK/IN IN IN IN/PD IN IN IN IN IN IN IN GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O IN PLCC/LCC 25 24 23 22 21 20 19 12 13 14 15 16 17 18 5 6 7 8 9 10 11 I/O I/O I/O GND* I/O I/O I/O IN IN GND GND* IN I/O I/O IN/PD IN IN GND* IN IN IN 4 3 2 1 28 27 26 IN IN CLK/IN VCC* VCC I/O I/O Figure 2-3. Figure 2-2. Note: 2 For all PLCCs (except "-5"), pins 1, 8, 15 and 22 can be left unconnected. However, if they are connected, superior performance will be achieved Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 3. Absolute Maximum Ratings* Temperature under Bias ................. -55C to +125C *NOTICE: Storage Temperature...................... -65C to +150C Voltage on Any Pin with Respect to Ground...........................-2.0V to +7.0V(1) Voltage on Input Pins with Respect to Ground during Programming ......................-2.0V to +14.0V(1) Note: Programming Voltage with Respect to Ground.........................-2.0V to +14.0V(1) 4. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 1. Minimum voltage is -0.6V DC, which may undershoot to 2.0V for pulses of less than 20ns. Maximum output pin voltage is VCC + 0.75V DC, which may overshoot to 7.0V for pulses of less than 20ns. DC and AC Operating Conditions Operating Temperature (Ambient) VCC Power Supply Commercial Industrial Military 0C - 70C -40C - 85C -55C - 125C (case) 5V 5% 5V 10% 5V 10% 3 0735U-PLD-7/10 4.1 DC Characteristics Symbol Parameter Condition IIL Input or I/O Low Leakage Current IIH Input or I/O High Leakage Current ICC ICC2 Power Supply Current, Standby Clocked Power Supply Current Min Typ Max Units 0 VIN VIL (Max) -10.0 A 3.5 VIN VCC 10.0 A C-5, 7, 10 Com. 85.0 130.0 mA C-10 Ind. 90.0 140.0 mA C-15 Ind. 65.0 115.0 mA CQ-15 Ind. 35.0 70.0 mA C-5, 7, 10 Com. 150.0 mA C-10 Ind., Mil. 160.0 mA C-15 Ind. 125 mA C-15 Mil. 160.0 mA CQ-15 Ind. 40.0 80.0 mA VCC = Max Com. 10.0 500.0 A VIN = 0, Max Ind. 10.0 650.0 A -130.0 mA VCC = Max, VIN = Max, Outputs Open VCC = Max, Outputs Open, f = 15MHz 70.0 IPD Power Supply Current, PD Mode IOS(1) Output Short Circuit Current VIL Input Low Voltage -0.5 0.8 V VIH Input High Voltage 2.0 VCC+0.75 V VOL Output Low Voltage VOH Output High Voltage VOUT = 0.5V VIN = VIH or VIL, VCC = Min VIN = VIH or VIL, VCC = Min IOL = 16mA Com., Ind. 0.5 V IOL = 12mA Mil. 0.5 V IOH = -4.0mA 2.4 Note: 1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec 4.2 AC Waveforms (1) V CLOCK Note: 4 1. Timing measurement reference is 1.5V. Input AC driving levels are 0.0V and 3.0V, unless otherwise specified Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 4.3 AC Characteristics(1) -5 -7 -10 -15 Symbol Parameter Min Max Min Max Min Max Min Max Units tPD Input or Feedback to Combinatorial Output 1.0 5.0 3.0 7.5 3.0 10.0 3.0 15.0 ns tCO Clock to Output 1.0 4.0 2.0 4.5(2) 2.0 6.5 2.0 8.0 ns tCF Clock to Feedback 2.5 ns tS Input or Feedback Setup Time tH Hold Time 2.5 2.5 3.0 3.5 0 0 4.5 10.0 ns 0 0 ns 90.0 55.5 MHz External Feedback 1/(tS + tCO) 142.0 Internal Feedback 1/(tS + tCF) 166.0 142.0 117.0 80.0 MHz No Feedback 1/(tWH + tWL) 166.0 166.0 125.0 83.3 MHz tW Clock Width (tWL and tWH) 3.0 3.0 3.0 6.0 ns tEA Input or I/O to Output Enable 2.0 6.0 3.0 7.5 3.0 10.0 3.0 15.0 ns tER Input or I/O to Output Disable 2.0 5.0 3.0 7.5 3.0 9.0 3.0 15.0 ns tAP Input or I/O to Asynchronous Reset of Register 3.0 7.0 3.0 10.0 3.0 12.0 3.0 20.0 ns tAW Asynchronous Reset Width 5.5 7.0 8.0 15.0 ns tAR Asynchronous Reset Recovery Time 4.0 5.0 6.0 10.0 ns tSP Setup Time, Synchronous Preset 4.0 4.5 6.0 10.0 ns tSPR Synchronous Preset to Clock Recovery Time 4.0 5.0 8.0 10.0 ns fMAX Notes: 125.0 (3) 2.5 1. See ordering information for valid part numbers 2. 5.5ns for DIP package devices 3. 111MHz for DIP package devices 5 0735U-PLD-7/10 4.4 Power-down AC Characteristics(1)(2)(3) -5 -7 Min Max Min -15 Symbol Parameter Min tIVDH Valid Input before PD High 5.0 7.5 10.0 15.0 ns tGVDH Valid OE before PD High 0 0 0 0 ns tCVDH Valid Clock before PD High 0 0 0 tDHIX Input Don't Care after PD High 5.0 7.0 10.0 15.0 ns tDHGX OE Don't Care after PD High 5.0 7.0 10.0 15.0 ns tDHCX Clock Don't Care after PD High 5.0 7.0 10.0 15.0 ns tDLIV PD Low to Valid Input 5.0 7.5 10.0 15.0 ns tDLGV PD Low to Valid OE 15.0 20.0 25.0 30.0 ns tDLCV PD Low to Valid Clock 15.0 20.0 25.0 30.0 ns tDLOV PD Low to Valid Output 20.0 25.0 30.0 35.0 ns Notes: Max -10 Max Min Max Units ns 1. Output data is latched and held 2. High-Z outputs remain high-Z 3. Clock and input transitions are ignored 4.5 Input Test Waveforms 4.5.1 Input Test Waveforms and Measurement Levels 4.5.2 Commercial Output Test Loads 4.6 Pin Capacitance Table 4-1. Typ Max Units Conditions CIN 5 8 pF VIN = 0V COUT 6 8 pF VOUT = 0V Note: 6 Pin Capacitance (f = 1MHz, T = 25C(1)) 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 4.7 Power-up Reset The registers in the Atmel(R) ATF22V10Cs are designed to reset during power-up. At a point delayed slightly from VCC crossing VRST, all registers will be reset to the low state. The output state will depend on the polarity of the output buffer. This feature is critical for state machine initialization. However, due to the asynchronous nature of reset and the uncertainty of how VCC actually rises in the system, the following conditions are required: 1. The VCC rise must be monotonic, and starts below 0.7V 2. After reset occurs, all input and feedback setup times must be met before driving the clock pin high 3. The clock must remain stable during tPR Figure 4-1. Power-up Reset Timing V R ST POWER t PR REGISTERED OUTPUTS tS tW CLOCK 4.8 Preload of Registered Outputs The ATF22V10C registers are provided with circuitry to allow loading of each register with either a high or a low. This feature will simplify testing since any state can be forced into the registers to control test sequencing. A JEDEC file with preload is generated when a source file with vectors is compiled. Once downloaded, the JEDEC file preload sequence will be done automatically by most of the approved programmers after the programming. 5. Electronic Signature Word There are 64-bits of programmable memory that are always available to the user, even if the device is secured. These bits can be used for user-specific data. 6. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF22V10C fuse patterns. Once programmed, fuse verify and preload are inhibited. However, the 64-bit User Signature remains accessible. The security fuse should be programmed last, as its effect is immediate. 7. Programming/Erasing Programming/erasing is performed using standard PLD programmers. See "CMOS PLD Programming Hardware and Software Support" for information on software/programming. Table 7-1. Programming/Erasing Parameter Description Typ Max Units tPR Power-up Reset Time 600 1,000 ns VRST Power-up Reset Voltage 3.8 4.5 V 7 0735U-PLD-7/10 8. Input and I/O Pin-keeper Circuits The Atmel(R) ATF22V10C contains internal input and I/O pin-keeper circuits. These circuits allow each ATF22V10C pin to hold its previous value even when it is not being driven by an external source or by the device's output buffer. This helps to ensure that all logic array inputs are at known valid logic levels. This reduces system power by preventing pins from floating to indeterminate levels. By using pin-keeper circuits rather than pull-up resistors, there is no DC current required to hold the pins in either logic state (high or low). These pin-keeper circuits are implemented as weak feedback inverters, as shown in the Input Diagram below. These keeper circuits can easily be overdriven by standard TTL- or CMOS-compatible drivers. The typical overdrive current required is 40A. 8 Figure 8-1. Input Diagram Figure 8-2. I/O Diagram Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 9. Power-down Mode The Atmel(R) ATF22V10C includes an optional pin-controlled power-down feature. When this mode is enabled, the PD pin acts as the power-down pin (Pin 4 on the DIP/SOIC packages and Pin 5 on the PLCC package). When the PD pin is high, the device supply current is reduced to less than 100mA. During power-down, all output data and internal logic states are latched and held. Therefore, all registered and combinatorial output data remain valid. Any outputs that were in an undetermined state at the onset of power-down will remain at the same state. During power-down, all input signals except the power-down pin are blocked. Input and I/O hold latches remain active to ensure that pins do not float to indeterminate levels, further reducing system power. The power-down pin feature is enabled in the logic design file. Designs using the power-down pin may not use the PD pin logic array input. However, all other PD pin macrocell resources may still be used, including the buried feedback and foldback product term array inputs. PD pin configuration is controlled by the design file, and appears as a separate fuse bit in the JEDEC file. When the power-down feature is not specified in the design file, the IN/PD pin will be configured as a regular logic input. Note: 10. Some programmers list the 22V10 JEDEC compatible 22V10C (no PD used) separately from the non-22V10 JEDEC compatible 22V10CEX (with PD used) Compiler Mode Selection Table 10-1. Compiler Mode Selection PAL Mode (5828 Fuses) GAL Mode (5892 Fuses) Power-down Mode(1) (5893 Fuses) Synario ATF22V10C (DIP) ATF22V10C (PLCC) ATTF22V10C DIP (UES) ATF22C10C PLCC (UES) ATF22V10C DIP (PWD) ATF22V10C PLCC (PWD) WINCUPL P22V10 P22V10LCC G22V10 G22V10LCC G22V10CP G22V10CPLCC Note: 1. These device types will create a JEDEC file which when programmed in Atmel ATF22V10C devices will enable the power-down mode feature. All other device types have the feature disabled 9 0735U-PLD-7/10 11. 10 Functional Logic Diagram Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) ATMEL ATF22V10C/CQ NORMALIZED ICC VS. TEMPERATURE ATMEL ATF22V10C/CQ SUPPLY CURRENT VS. SUPPLY VOLTAGE (TA = 25C) 1.1 140.0 120.0 I CC (mA) NORMALIZED ICC C-5, -7, -10 100.0 C-15 80.0 CQ-15 60.0 40.0 20.0 1.0 0.9 0.8 0.0 4.50 4.75 5.00 5.25 -40.0 5.50 25.0 ATMEL ATF22V10C/CQ SUPPLY CURRENT VS. INPUT FREQUENCY (VCC = 5V, TA = 25C) ATMEL ATF22V10C/CQ OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE (VCC = 5V, TA = 25C) C-5, 7, 10 80.0 IOH (mA) C-15 CQ-15 40.0 0.0 0.0 10.0 20.0 0.0 -10.0 -20.0 -30.0 -40.0 -50.0 -60.0 -70.0 -80.0 -90.0 50.0 0.0 0.5 1.0 1.5 2.0 FREQUENCY (MHz) 3.0 3.5 4.0 4.5 5.0 ATMEL ATF22V10C/CQ OUTPUT SINK CURRENT VS. SUPPLY VOLTAGE (VOL = 0.5V) 0.0 -5.0 -10.0 -15.0 -20.0 -25.0 -30.0 -35.0 -40.0 -45.0 -50.0 140.0 120.0 100.0 IOL (mA) IOH (mA) 2.5 VOH (V) ATMEL ATF22V10C/CQ OUTPUT SOURCE CURRENT VS. SUPPLY VOLTAGE (VOH = 2.4V) 80.0 60.0 40.0 20.0 0.0 4.0 4.5 5.0 5.5 6.0 0.0 0.5 1.0 SUPPLY VOLTAGE (V) 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) ATMEL ATF22V10C/CQ OUTPUT SINK CURRENT VS. SUPPLY VOLTAGE (VOL = 0.5V) ATMEL ATF22V10C/CQ INPUT CLAMP CURRENT VS. INPUT VOLTAGE (VCC = 5V, TA = 35C) 0.0 46.0 45.0 44.0 43.0 42.0 41.0 40.0 39.0 38.0 37.0 INPUT CURRENT (mA) IOL (mA) 75.0 TEMPERATURE (C) 120.0 I CC (mA) 0.0 SUPPLY VOLTAGE (V) -20.0 -40.0 -60.0 -80.0 -100.0 -120.0 4.0 4.5 5.0 SUPPLY VOLTAGE (V) 5.5 6.0 0.0 -0.2 -0.4 -0.6 -0.8 -1.0 INPUT VOLTAGE (V) 11 0735U-PLD-7/10 ATMEL ATF22V10C/CQ NORMALIZED TCO VS. TEMPERATURE ATMEL ATF22V10C/CQ NORMALIZED TPD VS. VCC 1.1 NORMALIZED TCO NORMALIZED TPD 1.2 1.1 1.0 0.9 0.8 1.0 0.9 0.8 4.50 4.75 5.00 5.25 5.50 -40.0 0.0 SUPPLY VOLTAGE (V) 1.1 NORMALIZED TSU NORMALIZED TCO 1.3 1.2 1.1 1.0 0.9 0.8 1.0 0.9 0.8 4.50 4.75 5.00 5.25 5.50 -40.0 0.0 SUPPLY VOLTAGE (V) 75.0 ATMEL ATF22V10C/CQ DELTA TPD VS. OUTPUT LOADING 8.0 DELTA TPD (ns) 1.2 NORMALIZED TSU 25.0 TEMPERATURE (C) ATMEL ATF22V10C/CQ NORMALIZED TSU VS. VCC 1.1 1.0 0.9 6.0 4.0 2.0 0.0 -2.0 0.8 4.50 4.75 5.00 5.25 0 5.50 50 100 150 200 250 300 OUTPUT LOADING (pF) SUPPLY VOLTAGE (V) ATMEL ATF22V10C/CQ DELTA T PD VS. NUMBER OF OUTPUT SWITCHING ATMEL ATF22V10C/CQ NORMALIZED TPD VS. TEMPERATURE 1.1 0.0 DELTA TPD (ns) NORMALIZED TPD 75.0 ATMEL ATF22V10C/CQ NORMALIZED TSU VS. TEMPERATURE ATMEL ATF22V10C/CQ NORMALIZED TCO VS. VCC 1.0 0.9 0.8 -0.1 -0.2 -0.3 -0.4 -0.5 -40.0 0.0 25.0 TEMPERATURE (C) 12 25.0 TEMPERATURE (C) 75.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 NUMBER OF OUTPUTS SWITCHING Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) ATMEL ATF22V10C/CQ DELTA TCO VS. OUTPUT LOADING ATMEL ATF22V10C/CQ DELTA TCO VS. NUMBER OF SWITCHING 0.0 8.0 DELTA TCO (ns) DELTA TCO (ns) 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 50 100 150 200 250 NUMBER OF OUTPUTS LOADING 300 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 NUMBER OF OUTPUTS SWITCHING 13 0735U-PLD-7/10 12. Ordering Information 12.1 Atmel ATF22V10C(Q) Green Package Options (Pb/Halide-free/RoHS Compliant) tPD (ns) tS (ns) tCO (ns) 5 3 4 7.5 3.5 7.5 3.5 10 4.5 15 10 Ordering Code Package Operation Range ATF22V10C-5JX 28J Commercial (0C to 70C) 4.5 ATF22V10C-7PX ATF22V10C-7SX 24P3 24S Commercial (0C to 70C) 4.5 ATF22V10C-7JU 28J Industrial (-40C to 85C) 6.5 ATF22V10C-10JU ATF22V10C-10PU ATF22V10C-10SU ATF22V10C-10XU 28J 24P3 24S 24X Industrial (-40C to 85C) ATF22V10C-15JU ATF22V10C-15PU 28J 24P3 Industrial (-40C to 85C) 28J Industrial (-40C to 85C) 8 ATF22V10CQ-15JU 12.2 Using "C" Product for Industrial To use commercial product for industrial temperature ranges, down-grade one speed grade from the industrialgrade to the commercial-grade device (e.g. 7ns PX = 10ns PU) and de-rate power by 30%. 12.3 Military Package Options (Lead-based)(1) tPD (ns) 10 15 Notes: tS (ns) 4.5 10 tCO (ns) 6.5 8 Ordering Code Package ATF22V10C-10GM/883 ATF22V10C-10NM/883 24D3 28L 5962-8984116LA 5962-89841163A 24D3 28L ATF22V10C-15GM/883 ATF22V10C-15NM/883 24D3 28L 5962-8984115LA 5962-89841153A 24D3 28L Operation Range Military (-55C to 125C) Class B, Fully Compliant Military (-55C to 125C) Class B, Fully Compliant 1. Military/DSCC parts meet the DSCC drawing specifications Package Type 14 24D3 24-lead, 0.300" Wide, Non-windowed Ceramic Dual Inline Package (CERDIP) 24P3 24-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 24S 24-lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC) 24X 24-lead, 4.4mm Wide, Plastic Thin Shrink Small Outline (TSSOP) 28J 28-lead, Plastic J-leaded Chip Carrier (PLCC) 28L 28-lead, Ceramic Leadless Chip Carrier (LCC) Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 13. Packaging Information 13.1 24D3 - CERDIP Dimensions in Millimeters and (Inches). Controlling dimension: Inches. MIL-STD 1835 D-9 Config A (Glass Sealed) 32.51(1.280) 31.50(1.240) PIN 1 7.87(0.310) 7.24(0.285) 27.94(1.100) REF 5.08(0.200) MAX 0.127(0.005) MIN SEATING PLANE 5.08(0.200) 3.18(0.125) 2.45(0.100)BSC 0.46(0.018) 0.20(0.008) 1.65(0.065) 1.14(0.045) 1.52(0.060) 0.38(0.015) 0.66(0.026) 0.36(0.014) 8.13(0.320) 7.37(0.290) 0~ 15 REF 10.20(0.400) MAX 10/21/03 Package Drawing Contact: packagedrawings@atmel.com TITLE 24D3, 24-lead, 0.300" Wide. Non-windowed, Ceramic Dual Inline Package (Cerdip) DRAWING NO. 24D3 REV. B 15 0735U-PLD-7/10 13.2 24P3 - PDIP D PIN 1 E1 A SEATING PLANE A1 L B B1 e E COMMON DIMENSIONS (Unit of Measure = mm) C eC eB Notes: 1. 2. This package conforms to JEDEC reference MS-001, Variation AF Dimensions D and E1 do not include mold Flash or Protrusion Mold Flash or Protrusion shall not exceed 0.25mm (0.010") MIN SYMBOL NOM MAX A - - 5.334 A1 0.381 - - D 31.623 - 32.131 E 7.620 - 8.255 E1 6.096 - 7.112 B 0.356 - 0.559 B1 1.270 - 1.651 L 2.921 - 3.810 C 0.203 - 0.356 eB - - 10.922 eC 0.000 - 1.524 e NOTE Note 2 Note 2 2.540 TYP 6/1/04 Package Drawing Contact: packagedrawings@atmel.com 16 TITLE 24P3, 24-lead (0.300"/7.62mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 24P3 REV. D Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 13.3 24S - SOIC B D1 D PIN 1 ID PIN 1 e E A COMMON DIMENSIONS (Unit of Measure = mm) A1 0 8 L1 L SYMBOL MIN NOM MAX A - - 2.65 A1 0.10 - 0.30 D 10.00 - 10.65 D1 7.40 - 7.60 E 15.20 - 15.60 B 0.33 - 0.51 L 0.40 - 1.27 L1 0.23 - 0.32 e NOTE 1.27 BSC 06/17/2002 Package Drawing Contact: packagedrawings@atmel.com TITLE 24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC) DRAWING NO. REV. 24S B 17 0735U-PLD-7/10 13.4 24X - TSSOP Dimensions in Millimeter and (Inches)* JEDEC STANDARD MO-153 AD Controlling dimension: millimeters 0.30(0.012) 0.19(0.007) 4.48(0.176) 6.50(0.256) 4.30(0.169) 6.25(0.246) PIN 1 0.65(0.0256)BSC 7.90(0.311) 1.20(0.047)MAX 7.70(0.303) 0.15(0.006) 0.05(0.002) 0 0.20(0.008) 8 0.09(0.004) 0.75(0.030) 0.45(0.018) 04/11/2001 Package Drawing Contact: packagedrawings@atmel.com 18 TITLE 24X, 24-lead (4.4mm body width) Plastic Thin Shrink Small Outline Package (TSSOP) DRAWING NO. REV. 24X A Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 13.5 28J - PLCC 1.14(0.045) X 45 PIN NO. 1 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) IDENTIFIER E1 E D2/E2 B1 B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AB 2. Dimensions D1 and E1 do not include mold protrusion Allowable protrusion is .010"(0.254mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line 3. Lead coplanarity is 0.004" (0.102mm) maximum SYMBOL MIN NOM MAX A 4.191 - 4.572 A1 2.286 - 3.048 A2 0.508 - - D 12.319 - 12.573 D1 11.430 - 11.582 E 12.319 - 12.573 E1 11.430 - 11.582 D2/E2 9.906 - 10.922 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 Package Drawing Contact: packagedrawings@atmel.com TITLE 28J, 28-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 28J B 19 0735U-PLD-7/10 13.6 28L - LCC Dimensions in Millimeters and (Inches). Controlling dimension: Inches. MIL-STD 1835 C-4 11.68(0.460) 11.23(0.442) 2.54(0.100) 2.16(0.085) 11.68(0.460) 11.23(0.442) PIN 1 2.41(0.095) 1.91(0.075) 1.40(0.055) 1.14(0.045) 1.91(0.075) 1.40(0.055) INDEX CORNER 0.635(0.025) X 45 0.381(0.015) 0.305(0.012) RADIUS 0.178(0.007) 7.62(0.300) BSC 0.737(0.029) 0.533(0.021) 1.27(0.050) TYP 1.02(0.040) X 45 7.62(0.300) BSC 2.16(0.085) 1.65(0.065) 10/21/03 Package Drawing Contact: packagedrawings@atmel.com 20 TITLE 28L, 28-pad, Non-windowed, Ceramic Lid, Leadless Chip Carrier (LCC) DRAWING NO. REV. 28L B Atmel ATF22V10C(Q) 0735U-PLD-7/10 Atmel ATF22V10C(Q) 14. Revision History Doc. Rev. Date Comments 0735U 05/2010 Updated C-15 military device ICC limit Revised the maximum power supply current in PD mode for commercial- and industrial-grade devices from 100A to 500A and 100A to 650A maximum, respectively C-15 and CQ-15 Commercial part removed from Table 4-1. Removed Mil from ICC, C-15 (Ind.) parts ICC2 at 15mhz Max changed from 90mA to 125mA 0735T 05/2009 Added military-grade packages and removed leaded parts 0735S 08/2008 Added new green part 0735R 06/2008 Updated Green package options 21 0735U-PLD-7/10 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1) (408) 441-0311 Fax: (+1) (408) 487-2600 www.atmel.com Atmel Asia Limited Unit 01-5 & 16, 19F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81) (3) 3523-3551 Fax: (+81) (3) 3523-7581 Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Product Contacts Technical Support PLD@atmel.com Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2010 Atmel Corporation. All rights reserved. Atmel (R), logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 0735U-PLD-7/10