CURRENT 1.0 Ampere VOLTAGE 50 to 1000 Volts FR101 THRU FR107 Features * Plastic package has Underwrites Laboratory Flammability Classification 94V-0 * Fast switching speed * Construction utilizes void-free molded plastic technique * Low forward voltage drop, high efficiency * High current capability * High reliability DO-41 0.107(2.7) 0.080(2.0) DIA. 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) Mechanical Data * Case : JEDEC DO-41 molded plastic body * Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 * Polarity : Color band denotes cathode end * Mounting Position : Any * Weight : 0.012 ounce, 0.33 gram 1.0(25.4) MIN. 0.034(0.9) 0.028(0.7) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25 ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols FR 101 FR 102 FR 103 FR 104 FR 105 FR 106 FR 107 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length TA=75 I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 30.0 Amps VF 1.3 Volts Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TL=55 5.0 100 Maximum reverse recovery time (Note 1) Trr Typical junction capacitance (Note 2) CJ Operating junction and storage temperature range A IR TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. 150 250 15.0 -65 to +150 500 ns pF RATINGS AND CHARACTERISTIC CURVES FR101 THRU FR107 FIG.2-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 1.0 50 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 0.8 0.6 0.4 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.2 0 0 25 50 75 100 125 150 40 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT(A) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 175 30 20 10 0 AMBIENT TEMPERATURE ( ) 1 2 4 6 8 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 10 6.0 4.0 INSTANTANEOUS REVERSE CURRENT ,(mA) INSTANTANEOUS FORWARD CURRENT(AMPERES) 20 10 3 1 0.3 0.1 2.0 1.0 0.6 0.4 0.2 TJ=25 0.03 0.02 Pulse Width=300mS 0.01 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 TJ=25 0.1 0.06 0.04 1.2 1.4 1.6 0 20 1.8 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE(%) INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) 200 100 50W NON INDUCTIVE 60 10W NON INDUCTIVE +0.5A Trr 40 (+) 20 D.U.T. PULSE GENERATOR (NOTE2) 25Vdc (APPROX) 10 6 ( TJ=25 ) 1W NON INDUCTIVE 4 2 1 0.1 0.2 0.4 1 2 4 REVERSE VOLTAGE. (V) 0 -0.25A 10 20 40 100 OSCILLOSCOPE (NOTE1) NOTES:1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm