LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 D D D D D D D D P PACKAGE (TOP VIEW) Output Current . . . 100 mA Low Loss . . . 1.1 V at 100 mA Operating Range . . . 3.5 V to 15 V Reference and Error Amplifier for Regulation External Shutdown External Oscillator Synchronization Devices Can Be Paralleled Pin-to-Pin Compatible With the LTC1044/7660 FB/SD CAP+ GND CAP- 1 8 2 7 3 6 4 5 VCC OSC VREF VOUT DW PACKAGE (TOP VIEW) NC NC FB/SD CAP+ GND CAP- NC NC description/ordering information The LT1054 is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 NC NC VCC OSC VREF VOUT NC NC NC - No internal connection The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 also can be shut down by grounding the feedback terminal. Supply current in shutdown typically is 100 A. The internal oscillator of the LT1054 runs at a nominal frequency of 25 kHz. The oscillator terminal can be used to adjust the switching frequency or to externally synchronize the LT1054. The LT1054C is characterized for operation over a free-air temperature range of 0C to 70C. The LT1054I is characterized for operation over a free-air temperature range of -40C to 85C. ORDERING INFORMATION PDIP (P) -40C 40 C to 85C 85 C SOIC (DW) PDIP (P) 0C to 70C ORDERABLE PART NUMBER PACKAGE TA SOIC (DW) Tube of 50 LT1054IP Tube of 40 LT1054IDW Reel of 2000 LT1054IDWR Tube of 50 LT1054CP Tube of 40 LT1054CDW Reel of 2000 LT1054CDWR TOP-SIDE MARKING LT1054IP LT1054I LT1054CP LT1054C Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Copyright (c) 2004, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 functional block diagram VREF VCC 6 8 2.5 V Ref R Drive + FB/SD OSC 1 CAP + - 7 2 CIN Q OSC CAP - Q 4 Drive R Drive 3 GND COUT 5 VOUT Drive External capacitors Pin numbers shown are for the P package. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V Input voltage range, VI: FB/SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to VCC OSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to Vref Junction temperature, TJ (see Note 2): LT1054C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125C LT1054I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135C Package thermal impedance, JA (see Notes 3 and 4): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . 57C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The absolute maximum supply-voltage rating of 16 V is for unregulated circuits. For regulation-mode circuits with VOUT 15 V, this rating may be increased to 20 V. 2. The devices are functional up to the absolute maximum junction temperature. 3. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can impact reliability. 4. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions 2 VCC Supply voltage TA Operating free-air free air temperature range LT1054C LT1054I POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN MAX 3.5 15 0 70 -40 85 UNIT V C LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 electrical characteristics over recommended operating conditions (unless otherwise noted) PARAMETER VO Vref TEST CONDITIONS UNIT MIN TYP MAX -4.7 Regulated output voltage VCC = 7 V, TJ = 25C, RL = 500 , See Note 5 -5 -5.2 Input regulation VCC = 7 V to 12 V, RL = 500 , See Note 5 Full range 5 25 mV Output regulation VCC = 7 V, RL = 100 to 500 , See Note 5 Full range 10 50 mV Voltage loss, VCC - |VO (see Note 6) 0.35 0.55 CI = CO = 100-F 100 F tantalum 1.1 1.6 Output resistance IO = 10 mA to 100 mA, 10 15 Oscillator frequency VCC = 3.5 V to 15 V kHz Reference voltage IO = 10 mA IO = 100 mA See Note 7 25C Full range Full range Full range I(REF) = 60 A A Maximum switch current ICC LT1054C LT1054I TA 15 25 35 25C 2.35 2.5 2.65 Full range 2.25 25C VCC = 3.5 V Supply current IO = 0 Supply current in shutdown V(FB/SD) = 0 V VCC = 15 V Full range Full range 2.75 300 V V V mA 2.5 4 3 5 100 200 mA A Full range is 0C to 70C for the LT1054C and -40C to 85C for the LT1054I. All typical values are at T = 25C. A NOTES: 5. All regulation specifications are for a device connected as a positive-to-negative converter/regulator with R1 = 20 k, R2 = 102.5 k, external capacitor CIN = 10 F (tantalum), external capacitor COUT = 100 F (tantalum) and C1 = 0.002 F (see Figure 15). 6. For voltage-loss tests, the device is connected as a voltage inverter, with terminals 1, 6, and 7 unconnected. The voltage losses may be higher in other configurations. CIN and COUT are external capacitors. 7. Output resistance is defined as the slope of the curve (VO versus IO) for output currents of 10 mA to 100 mA. This represents the linear portion of the curve. The incremental slope of the curve is higher at currents less than 10 mA due to the characteristics of the switch transistors. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Shutdown threshold voltage vs Free-air temperature 1 Supply current vs Input voltage 2 Oscillator frequency vs Free-air temperature 3 Supply current in shutdown vs Input voltage 4 Average supply current vs Output current 5 Output voltage loss vs Input capacitance 6 Output voltage loss vs Oscillator frequency (10 F) 7 Output voltage loss vs Oscillator frequency (100 F) 8 Regulated output voltage vs Free-air temperature 9 Reference voltage change vs Free-air temperature 10 Voltage loss vs Output current 11 Table of Figures FIGURE 4 Switched-Capacitor Building Block 12 Switched-Capacitor Equivalent Circuit 13 Circuit With Load Connected From VCC to VOUT 14 External-Clock System 15 Basic Regulation Configuration 16 Power-Dissipation-Limiting Resistor in Series With CIN 17 Motor-Speed Servo 18 Basic Voltage Inverter 19 Basic Voltage Inverter/Regulator 20 Negative-Voltage Doubler 21 Positive-Voltage Doubler 22 100-mA Regulating Negative Doubler 23 Dual-Output Voltage Doubler 24 5-V to 12-V Converter 25 Strain-Gage Bridge Signal Conditioner 26 3.5-V to 5-V Regulator 27 Regulating 200-mA +12-V to -5-V Converter 28 Digitally Programmable Negative Supply 29 Positive Doubler With Regulation (5-V to 8-V Converter) 30 Negative Doubler With Regulator 31 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS SHUTDOWN THRESHOLD VOLTAGE vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs INPUT VOLTAGE 0.6 5 0.5 0.4 I CC - Supply Current - mA Shutdown Threshold Voltage - V IO = 0 V(FB/SD) 0.3 0.2 3 2 1 0.1 0 -50 4 0 -25 0 25 50 75 100 0 5 10 VCC - Input Voltage - V TA - Free-Air Temperature - C Figure 1 15 Figure 2 OSCILLATOR FREQUENCY vs FREE-AIR TEMPERATURE SUPPLY CURRENT IN SHUTDOWN vs INPUT VOLTAGE 35 120 Supply Current in Shutdown - A Oscillator Frequency - kHz 33 31 29 VCC = 15 V 27 25 VCC = 3.5 V 23 21 19 100 V(FB/SD) = 0 80 60 40 20 17 15 -50 0 -25 0 25 50 75 100 0 TA - Free-Air Temperature - C Figure 3 10 5 VCC - Input Voltage - V 15 Figure 4 Data at high and low temperatures are applicable only within the recommended operating free-air temperature range. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE LOSS vs INPUT CAPACITANCE 140 1.4 120 1.2 IO = 100 mA 100 Output Voltage Loss - V Average Supply Current - mA AVERAGE SUPPLY CURRENT vs OUTPUT CURRENT 80 60 40 20 1.0 0.8 IO = 50 mA 0.6 IO = 10 mA 0.4 Inverter Configuration COUT = 100-F Tantalum fOSC = 25 kHz 0.2 0 0 20 40 60 80 0 100 0 10 Figure 5 2.5 Inverter Configuration CIN = 10-F Tantalum COUT = 100-F Tantalum 50 60 70 80 90 100 Inverter Configuration CIN = 100-F Tantalum COUT = 100-F Tantalum 2.25 2 2 Output Voltage Loss - V Output Voltage Loss - V 40 OUTPUT VOLTAGE LOSS vs OSCILLATOR FREQUENCY 2.5 1.75 1.5 IO = 100 mA 1.25 1 IO = 50 mA 0.75 0.5 1.75 1.5 1.25 IO = 100 mA 1 IO = 50 mA 0.75 0.5 IO = 10 mA 0.25 IO = 10 mA 0.25 0 0 1 10 Oscillator Frequency - kHz 100 1 Figure 7 6 30 Figure 6 OUTPUT VOLTAGE LOSS vs OSCILLATOR FREQUENCY 2.25 20 Input Capacitance - F IO - Output Current - mA 10 Oscillator Frequency - kHz Figure 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 100 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 TYPICAL CHARACTERISTICS REFERENCE VOLTAGE CHANGE vs FREE-AIR TEMPERATURE -4.7 100 -4.8 80 V ref - Reference Voltage Change - mV VO - Regulated Output Voltage - V REGULATED OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE -4.9 -5 -5.1 -11.6 -11.8 -12 -12.2 -12.4 -12.6 -50 -25 0 25 75 50 60 40 20 0 -20 VREF at 0 = 2.500 V -40 -60 -80 -100 -50 100 -25 0 25 50 75 100 125 TA - Free-Air Temperature - C TA - Free-Air Temperature - C Figure 10 Figure 9 VOLTAGE LOSS vs OUTPUT CURRENT 2 3.5 V VCC 15 V Ci = Co = 100 F 1.8 Voltage Loss - V 1.6 TJ = 125C 1.4 1.2 1 TJ = 25C 0.8 0.6 0.4 TJ = -55C 0.2 0 0 10 20 30 40 50 60 70 80 90 100 Output Current - mA Figure 11 Data at high and low temperatures are applicable only within the recommended operating free-air temperature range. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 PRINCIPLES OF OPERATION A review of a basic switched-capacitor building block is helpful in understanding the operation of the LT1054. When the switch shown in Figure 12 is in the left position, capacitor C1 charges to the voltage at V1. The total charge on C1 is q1 = C1V1. When the switch is moved to the right, C1 is discharged to the voltage at V2. After this discharge time, the charge on C1 is q2 = C1V2. The charge has been transferred from the source V1 to the output V2. The amount of charge transferred is shown in equation 1. Dq + q1 * q2 + C1(V1 * V2) (1) If the switch is cycled f times per second, the charge transfer per unit time (i.e., current) is as shown in equation 2. I+f Dq + f C1(1 * V2) (2) To obtain an equivalent resistance for a switched-capacitor network, this equation can be rewritten in terms of voltage and impedance equivalence as shown in equation 3. I + V1 * V2 + V1 * V2 1fC1 R EQUIV (3) V1 V2 f RL C1 C2 Figure 12. Switched-Capacitor Building Block A new variable, REQUIV, is defined as REQUIV = 1 / fC1. The equivalent circuit for the switched-capacitor network is shown in Figure 13. The LT1054 has the same switching action as the basic switched-capacitor building block. Even though this simplification does not include finite switch-on resistance and output-voltage ripple, it provides an insight into how the device operates. REQUIV V1 R EQUIV + 1 fC1 V2 C2 RL Figure 13. Switched-Capacitor Equivalent Circuit These simplified circuits explain voltage loss as a function of oscillator frequency (see Figure 7). As oscillator frequency is decreased, the output impedance eventually is dominated by the 1/fC1 term, and voltage losses rise. Voltage losses also rise as oscillator frequency increases. This is caused by internal switching losses that occur due to some finite charge being lost on each switching cycle. This charge loss per-unit-cycle, when multiplied by the switching frequency, becomes a current loss. At high frequency, this loss becomes significant and voltage losses again rise. The oscillator of the LT1054 is designed to operate in the frequency band where voltage losses are at a minimum. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 PRINCIPLES OF OPERATION Supply voltage VCC alternately charges CIN to the input voltage when CIN is switched in parallel with the input supply and then transfers charge to COUT when CIN is switched in parallel with COUT. Switching occurs at the oscillator frequency. During the time that CIN is charging, the peak supply current is approximately 2.2 times the output current. During the time that CIN is delivering a charge to COUT, the supply current drops to approximately 0.2 times the output current. An input supply bypass capacitor supplies part of the peak input current drawn by the LT1054 and averages the current drawn from the supply. A minimum input-supply bypass capacitor of 2 F, preferably tantalum or some other low equivalent-series-resistance (ESR) type, is recommended. A larger capacitor is desirable in some cases. An example of this would be when the actual input supply is connected to the LT1054 through long leads or when the pulse currents drawn by the LT1054 might affect other circuits through supply coupling. In addition to being the output terminal, VOUT is tied to the substrate of the device. Special care must be taken in LT1054 circuits to avoid making VOUT positive with respect to any of the other terminals. For circuits with the output load connected from VCC to VOUT or from some external positive supply voltage to VOUT, an external transistor must be added (see Figure 14). This transistor prevents VOUT from being pulled above GND during startup. Any small general-purpose transistor such as a 2N2222 or a 2N2219 device can be used. Resistor R1 should be chosen to provide enough base drive to the external transistor so that it is saturated under nominal output voltage and maximum output current conditions. R1 v V OUTb I OUT (4) VIN 1 2 CIN + 3 4 FB/SD VCC CAP+ OSC LT1054 GND VREF CAP- VOUT 8 Load VOUT 7 R1 6 5 + COUT Pin numbers shown are for the P package. Figure 14. Circuit With Load Connected from VCC to VOUT POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 PRINCIPLES OF OPERATION The voltage reference (Vref) output provides a 2.5-V reference point for use in LT1054-based regulator circuits. The temperature coefficient (TC) of the reference voltage has been adjusted so that the TC of the regulated output voltage is near zero. As seen in the typical performance curves, this requires the reference output to have a positive TC. This nonzero drift is necessary to offset a drift term inherent in the internal reference divider and comparator network tied to the feedback terminal. The overall result of these drift terms is a regulated output that has a slight positive TC at output voltages below 5 V and a slight negative TC at output voltages above 5 V. For regulator feedback networks, reference output current should be limited to approximately 60 A. Vref draws approximately 100 A when shorted to ground and does not affect the internal reference/regulator. This terminal also can be used as a pullup for LT1054 circuits that require synchronization. CAP+ is the positive side of input capacitor CIN and is driven alternately between VCC and ground. When driven to VCC, CAP+ sources current from VCC. When driven to ground, CAP+ sinks current to ground. CAP- is the negative side of the input capacitor and is driven alternately between ground and VOUT. When driven to ground, CAP- sinks current to ground. When driven to VOUT, CAP- sources current from COUT. In all cases, current flow in the switches is unidirectional, as should be expected when using bipolar switches. OSC can be used to raise or lower the oscillator frequency or to synchronize the device to an external clock. Internally, OSC is connected to the oscillator timing capacitor (Ct 150 pF), which is charged and discharged alternately by current sources of 7 A, so that the duty cycle is approximately 50%. The LT1054 oscillator is designed to run in the frequency band where switching losses are minimized. However, the frequency can be raised, lowered, or synchronized to an external system clock if necessary. The frequency can be increased by adding an external capacitor (C2 in Figure 15) in the range of 5-20 pF from CAP+ to OSC. This capacitor couples a charge into Ct at the switch transitions. This shortens the charge and discharge times and raises the oscillator frequency. Synchronization can be accomplished by adding an external pullup resistor from OSC to Vref. A 20-k pullup resistor is recommended. An open-collector gate or an npn transistor then can be used to drive OSC at the external clock frequency as shown in Figure 15. The frequency can be lowered by adding an external capacitor (C1 in Figure 15) from OSC to ground. This increases the charge and discharge times, which lowers the oscillator frequency. 1 2 FB/SD VCC CAP+ OSC LT1054 + 3 GND VREF 8 C2 VIN 7 6 C1 4 CAP- VOUT 5 Pin numbers shown are for the P package. Figure 15. External-Clock System 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION regulation The feedback/shutdown (FB/SD) terminal has two functions. Pulling FB/SD below the shutdown threshold ( 0.45 V) puts the device into shutdown. In shutdown, the reference/regulator is turned off and switching stops. The switches are set such that both CIN and COUT are discharged through the output load. Quiescent current in shutdown drops to approximately 100 A. Any open-collector gate can be used to put the LT1054 into shutdown. For normal (unregulated) operation, the device will restart when the external gate is shut off. In LT1054 circuits that use the regulation feature, the external resistor divider can provide enough pulldown to keep the device in shutdown until the output capacitor (COUT) has fully discharged. For most applications, where the LT1054 is run intermittently, this does not present a problem because the discharge time of the output capacitor is short compared to the off time of the device. In applications where the device has to start up before the output capacitor (COUT) has fully discharged, a restart pulse must be applied to FB/SD of the LT1054. Using the circuit shown in Figure 16, the restart signal can be either a pulse (tp > 100 s) or a logic high. Diode coupling the restart signal into FB/SD allows the output voltage to rise and regulate without overshoot. The resistor divider R3/R4 shown in Figure 16 should be chosen to provide a signal level at FB/SD of 0.7-1.1 V. FB/SD also is the inverting input of the LT1054 error amplifier and, as such, can be used to obtain a regulated output voltage. R3 VIN 1 2 CIN 10-F Tantalum R4 + VCC CAP+ OSC LT1054 3 4 Restart FB/SD GND VREF CAP- VOUT 7 6 R1 5 R2 Shutdown For example: To get VO = -5 V, referenced to the ground terminal of the LT1054 R2 + R1 2.2 F + 8 V OUT V REF 2 * 40 mV )1 + 20 kW |-5 V| )1 2.5 V * 40 mV 2 VOUT C1 + 102.6 kW + COUT 100-F Tantalum Where: R1 = 20 k VREF = 2.5 V Nominal Choose the closest 1% value. Pin numbers shown are for the P package. Figure 16. Basic Regulation Configuration POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION regulation (continued) The error amplifier of the LT1054 drives the pnp switch to control the voltage across the input capacitor (CIN), which determines the output voltage. When the reference and error amplifier of the LT1054 are used, an external resistive divider is all that is needed to set the regulated output voltage. Figure 16 shows the basic regulator configuration and the formula for calculating the appropriate resistor values. R1 should be 20 k or greater because the reference current is limited to 100 A. R2 should be in the range of 100 k to 300 k. Frequency compensation is accomplished by adjusting the ratio of CIN to COUT. For best results, this ratio should be approximately 1:10. Capacitor C1, required for good load regulation, should be 0.002 F for all output voltages. The functional block diagram shows that the maximum regulated output voltage is limited by the supply voltage. For the basic configuration, VOUT referenced to the ground terminal of the LT1054 must be less than the total of the supply voltage minus the voltage loss due to the switches. The voltage loss versus output current due to the switches can be found in the typical performance curves. Other configurations, such as the negative doubler, can provide higher voltages at reduced output currents. capacitor selection While the exact values of CIN and COUT are noncritical, good-quality low-ESR capacitors, such as solid tantalum, are necessary to minimize voltage losses at high currents. For CIN, the effect of the ESR of the capacitor is multiplied by four, because switch currents are approximately two times higher than output current. Losses occur on both the charge and discharge cycle, which means that a capacitor with 1 of ESR for CIN has the same effect as increasing the output impedance of the LT1054 by 4 . This represents a significant increase in the voltage losses. COUT alternately is charged and discharged at a current approximately equal to the output current. The ESR of the capacitor causes a step function to occur in the output ripple at the switch transitions. This step function degrades the output regulation for changes in output load current and should be avoided. A technique used to gain both low ESR and reasonable cost is to parallel a smaller tantalum capacitor with a large aluminum electrolytic capacitor. output ripple The peak-to-peak output ripple is determined by the output capacitor and the output current values. Peak-to-peak output ripple is approximated as: DV + I OUT 2fC OUT (5) Where: V = peak-to-peak ripple fOSC = oscillator frequency For output capacitors with significant ESR, a second term must be added to account for the voltage step at the switch transitions. This step is approximately equal to: 2I OUTESR of C OUT 12 (6) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION power dissipation The power dissipation of any LT1054 circuit must be limited so that the junction temperature of the device does not exceed the maximum junction-temperature ratings. The total power dissipation is calculated from two components-the power loss due to voltage drops in the switches, and the power loss due to drive-current losses. The total power dissipated by the LT1054 is calculated as: P [ V CC * V OUT I OUT ) V CCI OUT(0.2) (7) where both VCC and VOUT are referenced to ground. The power dissipation is equivalent to that of a linear regulator. Limited power-handling capability of the LT1054 packages causes limited output-current requirements, or steps can be taken to dissipate power external to the LT1054 for large input or output differentials. This is accomplished by placing a resistor in series with CIN as shown in Figure 17. A portion of the input voltage is dropped across this resistor without affecting the output regulation. Since switch current is approximately 2.2 times the output current and the resistor causes a voltage drop when CIN is both charging and discharging, the resistor chosen is as shown: RX + VX 4.4 I OUT (8) Where: VX VCC - [(LT1054 voltage loss)(1.3) + |VOUT|] and IOUT = maximum required output current The factor of 1.3 allows some operating margin for the LT1054. When using a 12-V to -5-V converter at 100-mA output current, calculate the power dissipation without an external resistor. P + (12 V * |*5 V|)(100 mA) ) (12 V)(100 mA)(0.2) P + 700 mW ) 240 mW + 940 mW (9) VIN 1 Rx 2 FB/SD VCC CAP+ OSC 8 7 LT1054 CIN + 3 4 GND VREF CAP- VOUT 6 R1 5 R2 VOUT C1 + COUT Pin numbers shown are for the P package. Figure 17. Power-Dissipation-Limiting Resistor in Series With CIN POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION power dissipation (continued) At RJA of 130C/W for a commercial plastic device, a junction temperature rise of 122C occurs. The device exceeds the maximum junction temperature at an ambient temperature of 25C. To calculate the power dissipation with an external resistor (RX), determine how much voltage can be dropped across RX. The maximum voltage loss of the LT1054 in the standard regulator configuration at 100 mA output current is 1.6 V. V X + 12 V * [(1.6 V)(1.3) ) |*5 V|] + 4.9 V (10) and RX + 4.9 V + 11 W (4.4)(100 mA) (11) The resistor reduces the power dissipated by the LT1054 by (4.9 V)(100 mA) = 490 mW. The total power dissipated by the LT1054 is equal to (940 mW - 490 mW) = 450 mW. The junction-temperature rise is 58C. Although commercial devices are functional up to a junction temperature of 125C, the specifications are tested to a junction temperature of 100C. In this example, this means limiting the ambient temperature to 42C. To allow higher ambient temperatures, the thermal resistance numbers for the LT1054 packages represent worst-case numbers, with no heat sinking and still air. Small clip-on heat sinks can be used to lower the thermal resistance of the LT1054 package. Airflow in some systems helps to lower the thermal resistance. Wide printed circuit board traces from the LT1054 leads help remove heat from the device. This is especially true for plastic packages. 10 V 1N4002 100 k 1 2 10 F - + + 3 1N5817 4 Tach OSC CAP+ GND VREF CAP- VOUT Motor NOTE: Motor-Tach is Canon CKT26-T5-3SAE. Pin numbers shown are for the P package. Figure 18. Motor-Speed Servo 14 8 7 LT1054 + - VCC FB/SD POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 6 5 5 F + 100-k Speed Control LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION 1 FB/SD 2 VCC CAP+ OSC 8 VIN + 2 F 7 LT1054 10 F 3 + 4 GND VREF CAP- VOUT 6 5 -VOUT 100 F + Pin numbers shown are for the P package. Figure 19. Basic Voltage Inverter 1 FB/SD VCC 2 CAP+ OSC LT1054 10 F 3 + 4 GND VREF CAP- VOUT 8 + 7 6 R1 20 k 5 R2 VOUT 0.002 F + + R2 + R1 VIN 2 F 100 F VOUT V REF 2 * 40 mV )1 + 20 kW V OUT )1 1.21 V Pin numbers shown are for the P package. Figure 20. Basic Voltage Inverter/Regulator POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION 1 2 10 F FB/SD VCC CAP+ OSC + 8 + VOUT 7 - LT1054 3 VIN 2 F + 4 GND VREF CAP- VOUT 6 QX 5 RX 100 F + VIN = -3.5 V to -15 V VOUT = 2 VIN + (LT1054 Voltage Loss) + (QX Saturation Voltage) VIN Pin numbers shown are for the P package. Figure 21. Negative-Voltage Doubler VIN 3.5 V to 15 V 1N4001 1N4001 + + 100 F + 10 F VOUT 1 - 2 FB/SD VCC CAP+ OSC 8 7 LT1054 3 VIN = 3.5 V to 15 V VOUT 2 VIN - (VL + 2 V Diode) VL = LT1054 Voltage Loss 4 GND CAP- VREF VOUT Pin numbers shown are for the P package. Figure 22. Positive-Voltage Doubler 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 6 5 + 2 F LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION VIN 3.5 V to 15 V + 2.2 F 1 2 + 10 F 10 F FB/SD VCC 7 CAP+ LT1054 #1 6 GND VREF 4 5 CAP- 1N4002 VOUT + + 10 F 100 F 4 + 0.002 F 10 F + VCC 8 7 CAP+ OSC LT1054 #2 6 GND VREF HP5082-2810 CAP+ of LT1054 #1 CAP- VOUT 5 1N4002 + R2 500 k + 3 FB/SD 20 k R1 40 k 10 F 1N4002 1N4002 2 VOUT SET OSC 3 + 1 8 10 F 1N4002 VOUT IOUT 100 mA MAX VIN = 3.5 V to 15 V VOUT MAX -2 VIN + [LT1054 Voltage Loss +2 (VDiode)] R2 + R1 VOUT V REF 2 * 40 mV )1 + R1 V OUT 1.21 V )1 Pin numbers shown are for the P package. Figure 23. 100-mA Regulating Negative Doubler POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION VI 3.5 V to 15 V 1N4001 1N4001 + + +VO 100 F 10 F - + 1 2 10 F 3 + 4 10 F FB/SD VCC CAP+ OSC LT1054 GND VREF CAP- VOUT 8 7 6 100 F + 5 + 1N4001 1N4001 - VI = 3.5 V to 15 V +VO 2 VIN - (VL + 2 VDiode) -VO -2 VI + (VL + 2 VDiode) VL = LT1054 Voltage Loss 1N4001 + 100 F -VO + Pin numbers shown are for the P package. Figure 24. Dual-Output Voltage Doubler VI = 5 V + 1 FB/SD VCC 5 F 8 100 F 2 10 F + 3 4 CAP+ OSC LT1054 #1 GND CAP- 1N914 1N914 VO +12 V IO = 25 mA + 10 F + 7 1 6 2 CAP+ VREF VOUT FB/SD 5 10 F 2N2219 100 F 1 k + 5 F + 3 VCC OSC LT1054 #2 GND VREF 4 CAP- VOUT 8 CAP- of LT1054 #1 7 6 20 k VO -12 V IO = 25 mA 5 + Pin numbers shown are for the P package. Figure 25. 5-V to 12-V Converter 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 100 F LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION 5V 10 k Input TTL or CMOS Low for On + 10 k 40 2N2907 8 0.022 F - 1 10 F Zero Trim 10 k 2 1/2 LT1013 3 + A1 301 k 100 k 100 k 5 k Gain Trim 5 k 10 k 350 1 F 200 k 1 2 10 F FB/SD VCC CAP+ OSC + 8 4 - 1 M A2 1/2 LT1013 5 + 4 7 VOUT 5V 7 3 k LT1054 #1 3 6 GND VREF CAP- VOUT 2N2222 6 5 + 100-F Tantalum Adjust Gain Trim For 3 V Out From Full-Scale Bridge Output of 24 mV Pin numbers shown are for the P package. Figure 26. Strain-Gage Bridge Signal Conditioner POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION VI 3.5 V to 5.5 V 1 20 k 2 1 F 1N914 (All) 1 2 10 F FB/SD VCC CAP+ OSC 3 4 GND VREF VOUT CAP- 3 8 7 LT1054 + + 6 5 4 5 F FB/SD VCC CAP+ OSC R2 + R1 VOUT GND VREF CAP- VOUT + V REF 2 * 40 mV + R1 V OUT 1.21 V )1 5 R1 20 k + 0.002 F R2 125 k 1N5817 Pin numbers shown are for the P package. Figure 27. 3.5-V to 5-V Regulator 20 6 R2 125 k + 100 F 3 k 2N2219 )1 7 LTC1044 - VI = 3.5 V to 5.5 V VO = 5 V IO MAX = 50 mA 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1N914 1 F VO + LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION 12 V 5 F + 1 FB/SD 2 10 1/2 W VCC OSC CAP+ LT1054 #1 3 VREF GND 4 VOUT CAP- + 10 F 1 8 10 1/2 W 7 R1 39.2 k 6 + 0.002 F 5 10 F VCC CAP+ OSC 8 HP5082-2810 7 LT1054 #2 3 VREF GND 6 20 k + 4 R2 200 k + 2 FB/SD 200 F R2 + R1 V OUT V REF 2 * 40 mV VOUT CAP- )1 + R1 V OUT 1.21 V 5 VO = -5 V IO = 0-200 mA )1 Pin numbers shown are for the P package. Figure 28. Regulating 200-mA +12-V to -5-V Converter 15 V 5 F + 11 20 k 2.5 V 1 2 10 F + 3 4 FB/SD VCC CAP+ OSC 16 LT1004-2.5 8 15 14 7 Digital Input AD558 13 12 20 k LT1054 GND VREF CAP- VOUT 6 5 VO = -VI (Programmed) + 100 F Pin numbers shown are for the P package. Figure 29. Digitally Programmable Negative Supply POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 LT1054 SWITCHED-CAPACITOR VOLTAGE CONVERTERS WITH REGULATORS SLVS033F - FEBRUARY 1990 - REVISED NOVEMBER 2004 APPLICATION INFORMATION VI = 5 V 50 k 1 1N5817 100 F 10 F + 1N5817 VO 8V + 0.03 F 8 VCC CAP+ OSC 2 10 k 10 k 7 LT1054 3 6 5.5 k 5V 10 k FB/SD GND VREF CAP- VOUT 4 5 - 1/2 LT1013 + 2.5 k 0.1 F Pin numbers shown are for the P package. Figure 30. Positive Doubler With Regulation (5-V to 8-V Converter) VI 3.5 V to 15 V 1 2 FB/SD VCC CAP+ OSC 8 7 R1 60 k LT1054 10 F + 3 4 10 F GND VREF CAP- VOUT 2 F + 6 100 F + 5 R2 1 M + + 0.002 F 1N4001 1N4001 -VO VI = 3.5 V to 15 V VO MAX 2 VIN + (VL + 2 VDiode) VL = LT1054 Voltage Loss R2 + R1 V OUT V REF 2 * 40 mV + )1 + R1 V OUT 1.21 V 100 F )1 Pin numbers shown are for the P package. Figure 31. Negative Doubler With Regulator 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 2 F + PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty LT1054CDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054CDWE4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054CDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054CDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054CDWRE4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054CDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LT1054CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LT1054IDW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054IDWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054IDWR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054IDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LT1054IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LT1054IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type LT1054Y OBSOLETE DIESALE Y 0 TBD Call TI Lead/Ball Finish MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2007 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LT1054CDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 LT1054IDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LT1054CDWR SOIC DW 16 2000 367.0 367.0 38.0 LT1054IDWR SOIC DW 16 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated