09/2008
159
Ø d ±0.05 p 15 22.5 p 27.5 p = 37.5
0.6 or 0.8* 0.8 1.0
*See size table.
All dimensions are in mm.
GENERAL TECHNICAL DATA
Dielectric: polypropylene lm - 2 sections.
Plates: metal layer deposited by evaporation under vacuum.
Winding: non-inductive type.
Leads: tinned wire.
Protection: plastic case, thermosetting resin lled.
Box material is solvent resistant and ame retardant according to
UL94 V0.
Marking: Manufacturer’s logo, series, capacitance, tolerance,
rated voltage, capacitor class, dielectric code, climatic category,
passive ammability category, manufacturing date code, approvals,
manufacturing plant.
Climatic category: 40/110/56 IEC 60068-1
Operating temperature range: -40 to +110°C
Related documents: IEC 60384-14; EN 60384-14.
ELECTRICAL CHARACTERISTICS
Rated voltage (VR): 440Vac / 1000Vdc; 50/60Hz
Capacitance range: 4700pF to 2.2µF
Capacitance values: E6 series (IEC 60063 Norm).
Capacitance tolerances (measured at 1 kHz):
±10% (K); ±20% (M).
Tolerance ±5% (J) available
upon request.
Dissipation factor (DF):
tgδ x 10-4 at +25°C ±5°C: 10 (6)* at 1kHz *
Typical value
Insulation resistance:
Test conditions
Temperature: +25°C±5°C
Voltage charge time: 1 min
Voltage charge: 100 Vdc
Performance
1x105 M for C0.33µF
30000 s for C>0.33µF
Test voltage between terminations (on all pieces):
1700Vac for 1 s + 2700Vdc for 1 s at +25°C±5°C
R.47
X2 CLASS (IEC 60384-14) - MKP Series
METALLIZED POLYPROPYLENE FILM CAPACITOR
SELF-HEALING PRoPERTIES
Typical applications: interference suppression and
«across-the-line» applications. Suitable for use in situations
where failure of the capacitor would not lead to danger of
electric shock.
PRoDUCT CoDE: R47
TEST METHOD AND PERFORMANCE
Damp heat, steady state:
Test conditions 1st
Temperature: +40°C ± 2°C
Relative humidity (RH): 93% ±2%
Test duration: 56 days
Test conditions 2nd
Temperature: +60°C ± 2°C
Relative humidity (RH): 95% ±2%
Test duration: 500 hours
Performance
Dielectric strength: no dielectric breakdown or
ashover at 4.3 x VR (d.c.)/1 min
Capacitance change |C/C|: 5%
Insulation resistance: 50% of initial limit.
Endurance:
Test conditions
Temperature: +110°C ± 2°C
Test duration: 1000 h
Voltage applied: 1.25 x VR +1000Vac 0.1 s/h
Performance
Dielectric strength: no dielectric breakdown or
ashover at 4.3 x VR (d.c.)/1 min
Capacitance change |C/C|: 10%
Insulation resistance: 50% of initial limit.
Resistance to soldering heat:
Test conditions
Solder bath temperature: +260°C ± 5°C
Dipping time (with heat screen):10 s ± 1 s
Performance
Capacitance change |C/C|: 2%
Pitch Box thickness (B) Maximum dimensions (mm)
(mm) (mm) B max H max L max
10.0 All B +0.2 H +0.1 L +0.2
15.0 <7.5 B +0.2 H +0.1 L +0.3
15.0 ≥7.5 B +0.2 H +0.1 L +0.5
22.5 All B +0.2 H +0.1 L +0.3
27.5 All B +0.2 H +0.1 L +0.3
37.5 All B +0.3 H +0.1 L +0.3
single sided metallized
polypropylene lm
2 sections
Winding scheme
Loose Taped
Fig.1 Fig.2
09/2008 160
R.47
X2 CLASS (IEC60384-14) - MKP Series
METALLIZED POLYPROPYLENE FILM CAPACITOR
SELF-HEALING PRoPERTIES
PRoDUCT CoDE: R47
APPROVALS
Approved according to IEC 60384-14
According to IEC 60065.
(*) ENEC mark has replaced all the following European
National marks:
Rated Cap. 440 Vac / 1000 Vdc
Std dimensions Ø d Max
dv/dt at
420Vdc
Part Number
B H L p (V/ µs)
4700 pF 4.0 9.0 13.0 10.0 0.6 750 R474F 1470 - - 01 -
6800 pF 5.0 11.0 13.0 10.0 0.6 750 R474F 1680 - - 01 -
8200 pF 6.0 12.0 13.0 10.0 0.6 750 R474F 1820 - - 01 -
0.010 µF 6.0 12.0 13.0 10.0 0.6 750 R474F 2100 - - 01 -
0.010 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2100 - - 01 -
0.012 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2120 - - 01 -
0.015 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2150 - - 01 -
0.018 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2180 - - 01 -
0.022 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2220 - - 01 -
0.027 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2270 - - 01 -
0.033 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2330 - - 01 -
0.039 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2390 - - 01 -
0.047 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2470 - - 01 -
0.047 µF 6.0 17.5 18.0 15.0 0.6 600 R474I 2470 - - 02 -
0.047 µF 9.0 12.5 18.0 15.0 0.6 600 R474I 2470 - - 03 -
0.056 µF 8.5 14.5 18.0 15.0 0.6 600 R474I 2560 - - 01 -
0.068 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2680 - - 01 -
0.068 µF 7.5 18.5 18.0 15.0 0.8 600 R474I 2680 - - 02 -
0.068 µF 13.0 12.0 18.0 15.0 0.8 600 R474I 2680 - - 03 -
0.082 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2820 - - 01 -
0.10 µF 11.0 19.0 18.0 15.0 0.8 600 R474I 3100 - - 01 -
0.047 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2470 - - 01 -
0.047 µF 6.5 13.5 26.5 22.5 0.8 300 R474N 2470 - - 02 -
0.068 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2680 - - 01 -
0.10 µF 7.0 16.0 26.5 22.5 0.8 300 R474N 3100 - - 01 -
0.12 µF 8.5 17.0 26.5 22.5 0.8 300 R474N 3120 - - 01 -
0.15 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3150 - - 01 -
0.18 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3180 - - 01 -
0.22 µF 11.0 20.0 26.5 22.5 0.8 300 R474N 3220 - - 01 -
0.27 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3270 - - 01 -
0.33 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3330 - - 01 -
0.15 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3150 - - 01 -
0.18 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3180 - - 01 -
0.22 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3220 - - 01 -
0.27 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3270 - - 02 -
0.33 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3330 - - 02 -
0.39 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3390 - - 01 -
0.47 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3470 - - 01 -
0.56 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3560 - - 01 -
0.68 µF 14.0 28.0 32.0 27.5 0.8 225 R474R 3680 - - 01 -
0.82 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 3820 - - 01 -
1.0 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4100 - - 01 -
1.2 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4120 - - 01 -
1.5 µF 22.0 37.0 32.0 27.5 0.8 225 R474R 4150 - - 01 -
0.47 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3470 - - 01 -
0.56 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3560 - - 01 -
0.68 µF 13.0 24.0 41.5 37.5 1.0 150 R474W 3680 - - 01 -
0.82 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 3820 - - 01 -
1.0 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 4100 - - 01 -
1.2 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4120 - - 01 -
1.5 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4150 - - 01 -
1.8 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4180 - - 01 -
2.2 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4220 - - 01 -
All dimensions are in mm
(*) ENEC
IEC 60384-14 Class X2 File No.
CA08.00101
UL 1414
up to 1µF, 85°C;
250Vac) Across-the-line File No. E97797
UL 1283 Electromagnetic
Interference
Filters File No. E85238
Table 1
Standard
packaging style Lead
length
(mm)
Taping style Ordering
code
(Digit 10 to 11)
P2
(mm) Fig.
(No.) Pitch
(mm)
AMMo-PACK
AMMo-PACK 12.70
19.05 1
210.0/15.0
22.5 DQ
DQ
REEL Ø500mm
REEL Ø500mm
12.70
19.05 1
210.0/15.0
22.5/27.5 CK
CK
Loose, short leads
Loose, long leads
Loose, long leads
04 +2
25 -1/+2
30 +5
00
50
40
Note: Ammo-pack is the preferred packaging for taped version.
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
09/2008
161
GENERAL TECHNICAL DATA
Dielectric: polypropylene lm - 2 sections.
Plates: metal layer deposited by evaporation under vacuum.
Winding: non-inductive type.
Leads: tinned wire.
Protection: plastic case, thermosetting resin lled.
Box material is solvent resistant and ame retardant according to
UL94 V0.
Marking: Manufacturer’s logo, series, capacitance, tolerance,
rated voltage, capacitor class, dielectric code, climatic category,
passive ammability category, manufacturing date code, approvals,
manufacturing plant.
Climatic category: 40/110/56 IEC 60068-1
Operating temperature range: -40 to +110°C
Related documents: IEC 60384-14; EN60384-14
ELECTRICAL CHARACTERISTICS
Rated voltage (VR): 440Vac / 1000Vdc; 50/60Hz
Capacitance range: 4700pF to 2.2µF
Capacitance values: E6 series (IEC 60063 Norm).
Capacitance tolerances (measured at 1 kHz):
±10% (K); ±20% (M);
Tolerance ±5% (J) available
upon request.
Dissipation factor (DF):
tgδ x 10-4 at +25°C ±5°C: 10 (6)* at 1kHz *
Typical value
Insulation resistance:
Test conditions
Temperature: +25°C±5°C
Voltage charge time: 1 min
Voltage charge: 100 Vdc
Performance
1x105 M for C0.33µF
30000 s for C>0.33µF
Test voltage between terminations (on all pieces):
1700Vac for 1 s + 2700Vdc for 1 s at +25°C±5°C
R.47
X1 CLASS (IEC 60384-14) - MKP Series
METALLIZED POLYPROPYLENE FILM CAPACITOR
SELF-HEALING PRoPERTIES
Typical applications: interference suppression and «across-
the-line» applications. Suitable for use in situations where
failure of the capacitor would not lead to danger of electric
shock.
Class X1 shall be applied for PERMANENTLY CoNNECTED
APPARATUS.
Note: PERMANENTLY CONNECTED APPARATUS:
apparatus which is intended for connection to the mains
by a connection which cannot be loosened BY HAND.
BY HAND:
operation that does not require the use of any object
such a tool, coin, etc.
PRoDUCT CoDE: R47
Pitch Box thickness (B) Maximum dimensions (mm)
(mm) (mm) B max H max L max
10.0 All B +0.2 H +0.1 L +0.2
15.0 <7.5 B +0.2 H +0.1 L +0.3
15.0 ≥7.5 B +0.2 H +0.1 L +0.5
22.5 All B +0.2 H +0.1 L +0.3
27.5 All B +0.2 H +0.1 L +0.3
37.5 All B +0.3 H +0.1 L +0.3
TEST METHOD AND PERFORMANCE
Damp heat, steady state:
Test conditions 1st
Temperature: +40°C ± 2°C
Relative humidity (RH): 93% ±2%
Test duration: 56 days
Test conditions 2nd
Temperature: +60°C ± 2°C
Relative humidity (RH): 95% ±2%
Test duration: 500 hours
Performance
Dielectric strength: no dielectric breakdown or
ashover at 4.3 x VR (d.c.)/1 min
Capacitance change |C/C|: 5%
Insulation resistance: 50% of initial limit.
Endurance:
Test conditions
Temperature: +110°C ± 2°C
Test duration: 1000 h
Voltage applied: 1.25 x VR +1000Vac 0.1 s/h
Performance
Dielectric strength: no dielectric breakdown or
ashover at 4.3 x VR (d.c.)/1 min
Capacitance change |C/C|: 10%
Insulation resistance: 50% of initial limit.
Resistance to soldering heat:
Test conditions
Solder bath temperature: +260°C ± 5°C
Dipping time (with heat screen):10 s ± 1 s
Performance
Capacitance change |C/C|: 2%
Ø d ±0.05 p 15 22.5 p 27.5 p = 37.5
0.6 or 0.8* 0.8 1.0
*See size table.
All dimensions are in mm.
Loose Taped
Fig.1 Fig.2
Rated Cap. 440 Vac / 1000 Vdc
Std dimensions Ø d Max
dv/dt at
420Vdc
Part Number
B H L p (V/ µs)
4700 pF 4.0 9.0 13.0 10.0 0.6 750 R474F 1470 - - A1 -
6800 pF 5.0 11.0 13.0 10.0 0.6 750 R474F 1680 - - A1 -
8200 pF 6.0 12.0 13.0 10.0 0.6 750 R474F 1820 - - A1 -
0.010 µF 6.0 12.0 13.0 10.0 0.6 750 R474F 2100 - - A1 -
0.010 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2100 - - A1 -
0.012 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2120 - - A1 -
0.015 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2150 - - A1 -
0.018 µF 5.0 11.0 18.0 15.0 0.6 600 R474I 2180 - - A1 -
0.022 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2220 - - A1 -
0.027 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2270 - - A1 -
0.033 µF 6.0 12.0 18.0 15.0 0.6 600 R474I 2330 - - A1 -
0.039 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2390 - - A1 -
0.047 µF 7.5 13.5 18.0 15.0 0.6 600 R474I 2470 - - A1 -
0.047 µF 6.0 17.5 18.0 15.0 0.6 600 R474I 2470 - - A2 -
0.047 µF 9.0 12.5 18.0 15.0 0.6 600 R474I 2470 - - A3 -
0.056 µF 8.5 14.5 18.0 15.0 0.6 600 R474I 2560 - - A1 -
0.068 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2680 - - A1 -
0.068 µF 7.5 18.5 18.0 15.0 0.8 600 R474I 2680 - - A2 -
0.068 µF 13.0 12.0 18.0 15.0 0.8 600 R474I 2680 - - A3 -
0.082 µF 10.0 16.0 18.0 15.0 0.8 600 R474I 2820 - - A1 -
0.10 µF 11.0 19.0 18.0 15.0 0.8 600 R474I 3100 - - A1 -
0.047 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2470 - - A1 -
0.047 µF 6.5 13.5 26.5 22.5 0.8 300 R474N 2470 - - A2 -
0.068 µF 6.0 15.0 26.5 22.5 0.8 300 R474N 2680 - - A1 -
0.10 µF 7.0 16.0 26.5 22.5 0.8 300 R474N 3100 - - A1 -
0.12 µF 8.5 17.0 26.5 22.5 0.8 300 R474N 3120 - - A1 -
0.15 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3150 - - A1 -
0.18 µF 10.0 18.5 26.5 22.5 0.8 300 R474N 3180 - - A1 -
0.22 µF 11.0 20.0 26.5 22.5 0.8 300 R474N 3220 - - A1 -
0.27 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3270 - - A1 -
0.33 µF 13.0 22.0 26.5 22.5 0.8 300 R474N 3330 - - A1 -
0.15 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3150 - - A1 -
0.18 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3180 - - A1 -
0.22 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3220 - - A1 -
0.27 µF 9.0 17.0 32.0 27.5 0.8 225 R474R 3270 - - A2 -
0.33 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3330 - - A2 -
0.39 µF 11.0 20.0 32.0 27.5 0.8 225 R474R 3390 - - A1 -
0.47 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3470 - - A1 -
0.56 µF 13.0 22.0 32.0 27.5 0.8 225 R474R 3560 - - A1 -
0.68 µF 14.0 28.0 32.0 27.5 0.8 225 R474R 3680 - - A1 -
0.82 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 3820 - - A1 -
1.0 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4100 - - A1 -
1.2 µF 18.0 33.0 32.0 27.5 0.8 225 R474R 4120 - - A1 -
1.5 µF 22.0 37.0 32.0 27.5 0.8 225 R474R 4150 - - A1 -
0.47 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3470 - - A1 -
0.56 µF 11.0 22.0 41.5 37.5 1.0 150 R474W 3560 - - A1 -
0.68 µF 13.0 24.0 41.5 37.5 1.0 150 R474W 3680 - - A1 -
0.82 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 3820 - - A1 -
1.0 µF 16.0 28.5 41.5 37.5 1.0 150 R474W 4100 - - A1 -
1.2 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4120 - - A1 -
1.5 µF 19.0 32.0 41.5 37.5 1.0 150 R474W 4150 - - A1 -
1.8 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4180 - - A1 -
2.2 µF 20.0 40.0 41.5 37.5 1.0 150 R474W 4220 - - A1 -
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
All dimensions are in mm
R.47
X1 CLASS (IEC 60384-14) - MKP Series
METALLIZED POLYPROPYLENE FILM CAPACITOR
SELF-HEALING PRoPERTIES
PRoDUCT CoDE: R47
APPROVALS
(*) ENEC
IEC 60384-14 Class X1 File No.
CA08.00101
UL 1414
up to 1µF, 85°C;
250Vac) Across-the-line File No. E97797
UL 1283 Electromagnetic
Interference
Filters File No. E85238
Approved according to IEC 60384-14
According to IEC 60065.
(*) ENEC mark has replaced all the following European
National marks:
Table 1
Standard
packaging style Lead
length
(mm)
Taping style Ordering
code
(Digit 10 to 11)
P2
(mm) Fig.
(No.) Pitch
(mm)
AMMo-PACK
AMMo-PACK 12.70
19.05 1
210.0/15.0
22.5 DQ
DQ
REEL Ø500mm
REEL Ø500mm
12.70
19.05 1
210.0/15.0
22.5/27.5 CK
CK
Loose, short leads
Loose, long leads
Loose, long leads
04 +2
25 -1/+2
30 +5
00
50
40
Note: Ammo-pack is the preferred packaging for taped version.
single sided metallized
polypropylene lm
2 sections
Winding scheme
Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute
and we specifically disclaim any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who
have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.