CHEMTRONICS TDS # 2284 Technical Data Sheet Max-KleenTM XtremeTM The extra-strength, nonflammable heavy-duty degreaser PRODUCT DESCRIPTION Max-KleenTM XtremeTM is ideal for removal of all types of soils including tar and grease from tools, clutches, bearings and housings. It is a non-corrosive and nonconductive cleaner. This extra-strength degreaser evaporates quickly without leaving a residue behind. Max-KleenTM XtremeTM is registered with the NSF as a K1, K2 cleaner/degreaser for use in food processing facilities. * Quickly removes all types of tough soils including oxidized oil and grease * Dielectric strength of 18 kV * NSF K1, K2 registered * Contains n-propyl bromide * Nonflammable, no flash point * Penetrates to clean hard to reach areas * Non-corrosive and non-conductive * Leaves no residue * Ozone safe * Test on plastics TYPICAL APPLICATIONS Max-KleenTM XtremeTM can be used for all repair, maintenance, and manufacturing applications including: * Removes grease, oil, lubricants, wax and tar * Cleans contacts, relays and switches, circuit breakers and fuse blocks * All repair and maintenance cleaning including: controls, conveyors and gear drives * Cleans electric motors and gasoline engines * Removes tough soils from gears and pulleys * Use for maintenance of air compressors TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES Boiling Point 156 F (Initial) >1 Evaporation Rate (butyl acetate=1) Flash Point (TCC) None Specific Gravity 1.35 Vapor Pressure @68F Appearance 112 mmHg Clear, colorless liquid Odor Mild Solubility in Water Negligible Dielectric Breakdown (ASTM D-877) 18 kV Kauri-Butanol (KB) Number Shelflife NSF-Registered K1, K2 125 5 years #139458 (aerosol) #139459 (bulk) COMPATIBILITY Max-KleenTM Xtreme TM is compatible with most metals. As with any solvent, compatibility with plastics should be determined on a non-critical area prior to use. Materials such as polystyrene and ABS are not compatible with the cleaning solvent in Max-KleenTM Xtreme TM. AVAILABILITY Material ABS Buna-N EPDM Graphite HDPE LDPE Lexan Neoprene Noryl Nylon 66 Cross-Linked PE Polypropylene Polystyrene PVC Silicone Rubber Teflon Viton Compatibility Non-Compatible Fair Fair Excellent Excellent Good Fair Fair Poor Excellent Excellent Excellent Non-Compatible Excellent Poor Excellent Fair USAGE INSTRUCTIONS Read MSDS carefully prior to use. Spray 4-6 inches from surface to clean. Wash parts from top to bottom, allowing the liquid to flush away dirt and dissolved grease. For precise application use attached extension tube. Dip applications - Allow the soiled article to soak in Max-KleenTM XtremeTM for 5 - 10 minutes, then remove and loosen any remaining soils with a ControlwipesTM Wipe. For wipe applications, wet a ControlwipesTM Wipe with Max-KleenTM Xtreme TM and wipe away soils. When used to clean food equipment that will be returned to a food processing area, wash well with an acceptable detergent solution and rinse thoroughly with potable water. TECHNICAL & APPLICATION ASSISTANCE Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401. ES2284 ES184 ES5584 19 oz. aerosol 1 gallon liquid 55 gallon liquid SAFETY & ENVIRONMENTAL DATA SAFETY & ENVIRONMENTAL DATA CFC 0.0% VOC 100% HCFC-225 0.0% HFC 0.0% HCFC-141b 0.0% nPB 100% NOTE: This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. CHEMTRONICS does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it. Chemtronics is a registered trademark of Chemtronics. All rights reserved. Max-Kleen, XtremeTM and Controlwipes are trademarks of Chemtronics. All rights reserved. All other trademarks herein are trademarks or registered trademarks of their respective owners. CHEMTRONICS 8125 COBB CENTER DRIVE KENNESAW, GA 30152 REV C (08/13) 1-770-424-4888 DISTRIBUTED BY: