PRODUCT DESCRIPTION
Max-Kleen™ Xtreme™ is ideal for removal of
all types of soils including tar and grease from
tools, clutches, bearings and housings. It is a
non-corrosive and nonconductive cleaner. This
extra-strength degreaser evaporates quickly
without leaving a residue behind. Max-Kleen™
Xtreme™ is registered with the NSF as a K1, K2
cleaner/degreaser for use in food processing
facilities.
• Quickly removes all types of tough soils
including oxidized oil and grease
• Dielectric strength of 18 kV
• NSF K1, K2 registered
• Contains n-propyl bromide
• Nonflammable, no flash point
• Penetrates to clean hard to reach areas
• Non-corrosive and non-conductive
• Leaves no residue
• Ozone safe
• Test on plastics
TYPICAL APPLICATIONS
Max-Kleen™ Xtreme™ can be used for all
repair, maintenance, and manufacturing
applications including:
• Removes grease, oil, lubricants, wax and tar
• Cleans contacts, relays and switches, circuit
breakers and fuse blocks
• All repair and maintenance cleaning
including: controls, conveyors and gear
drives
• Cleans electric motors and gasoline engines
• Removes tough soils from gears and pulleys
• Use for maintenance of air compressors
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point
156° F
(Initial)
Evaporation Rate
(butyl acetate=1)
>1
Flash Point (TCC)
None
Specific Gravity
1.35
Vapor Pressure @68°F 112 mmHg
Appearance Clear, colorless liquid
Odor
Mild
Solubility in Water
Negligible
Dielectric Breakdown
(ASTM D-877)
18 kV
Kauri-Butanol
(KB) Number 125
Shelflife 5 years
NSF-Registered K1, K2 #139458 (aerosol)
#139459 (bulk)
COMPATIBILITY
Max-Kleen™ Xtreme ™ is compatible with most
metals. As with any solvent, compatibility with
plastics should be determined on a non-critical
area prior to use. Materials such as polystyrene
and ABS are not compatible with the cleaning
solvent in Max-Kleen™ Xtreme ™.
CHEMTRONICS
Technical Data Sheet
Max-Kleen™ Xtreme™
The extra-strength, nonflammable heavy-duty degr eas er
TDS # 2284
Material
Compatibility
ABS
Non-Compatible
Buna-N
Fair
EPDM
Fair
Graphite
Excellent
HDPE
Excellent
LDPE
Good
Lexan
Fair
Neoprene
Fair
Noryl
Poor
Nylon 66
Excellent
Cross-Linked PE
Excellent
Polypropylene
Excellent
Polystyrene
Non-Compatible
PVC
Excellent
Silicone Rubber
Poor
Teflon
Excellent
Viton
Fair
USAGE INSTRUCTIONS
Read MSDS carefully prior to use.
Spray 4-6 inches from surface to clean. Wash parts
from top to bottom, allowing the liquid to flush away
dirt and dissolved grease. For precise application use
attached extension tube.
Dip applications - Allow the soiled article to soak in
Max-Kleen™ Xtreme™ for 5 - 10 minutes, then remove
and loosen any remaining soils with a ControlwipesTM
Wipe.
For wipe applications, wet a Controlwipes™ Wipe with
Max-Kleen™ Xtreme ™ and wipe away soils.
When used to clean food equipment that will be returned
to a food processing area, wash well with an acceptable
detergent solution and rinse thoroughly with potable
water.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to answer
your technical and application related questions.
The toll free number is:
1-800-TECH-401.
AVAILABILITY
ES2284 19 oz. aerosol
ES184 1 gallon liquid
ES5584 55 gallon liquid
SAFETY & ENVIRONMENTAL DATA
SAFETY & ENVIRONMENTAL DATA
CFC 0.0% VOC 100%
HCFC-225 0.0% HFC 0.0%
HCFC-141b 0.0% nPB 100%
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS does not guarantee the accuracy
of the data and assumes no liability in connection
with damages incurred while using it.
Chemtronics is a registered trademark of Chemtronics. All
rights reserved. Max-Kleen, Xtreme™ and Controlwipes
are trademarks of Chemtronics. All rights reserved.
All other trademarks herein are trademarks or registered
trademarks of their respective owners.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV C (08/13)
DISTRIBUTED BY:
