Document Number: EN0555EJ4V1DS00 (4th edition)
Published date: June 2002 N CP(N)
ã NEC Corporation
2002 All rights reserved.
All information is subject to change without notice.
Please confirm the delivery specification before starting
to design your system.
TFT COLOR LCD MODULE
NL10276BC20-04
26.3cm (10.4 Type)
XGA
DATA SHEET
(4th edition)
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 2
INTRODUCTION
No part of this document shall be copied in any form or by any means without the prior written consent
of NEC Corporation.
NEC Corporation does not assume any liability for infringement of patents, copyrights or other
intellectual property rights of third parties by or arising from use of a product described herein or any
other liability arising from use of such application. No license, express, implied or otherwise, is granted
under any patents, copyrights or other intellectual property rights of NEC Corporation or of others.
While NEC Corporation has been making continuous effort to enhance the reliability of its products, the
possibility of failures cannot be eliminated entirely. To minimize risks of damage to property or injury to
person arising from a failure in an NEC product, customers must incorporate sufficient safety measures
in their design, such as redundancy, fire-containment and anti-failure features.
NEC products are classified into the following three quality grades:
"Standard", "Special", "Specific"
The "Specific" quality grade applies only to applications developed based on a customer designated
"quality assurance program" for a specific application. The recommended applications of a product
depend on its quality grade, as indicated below. Customers must check the quality grade of each
application before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment,
audio and visual equipment, home electronic appliances, machine tools, personal electronic
equipment and industrial robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically
designed for life support)
Specific: Military systems, aircraft, aerospace equipment, submersible repeaters, nuclear reactor control
systems, life support systems (medical equipment, etc.) and any other equipment
The quality grade of this product is "Standard" unless otherwise specified in this document. If
customers intend to use this product for applications other than those specified for "Standard" quality
grade, they should contact NEC Corporation sales representative in advance.
Anti-radioactive design is not implemented in this product.
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 3
CONTENTS
INTRODUCTION.......................................................................................................................................... 2
1. OUTLINE ................................................................................................................................................... 5
1.1 STRUCTURE AND PRINCIPLE.......................................................................................................... 5
1.2 APPLICATIONS.................................................................................................................................... 5
1.3 FEATURES............................................................................................................................................ 5
2. GENERAL SPECIFICATIONS................................................................................................................ 6
3. BLOCK DIAGRAM .................................................................................................................................. 7
4. DETAILED SPECIFICATIONS............................................................................................................... 8
4.1 MECHANICAL SPECIFICATIONS ..................................................................................................... 8
4.2 ABSOLUTE MAXIMUM RATINGS....................................................................................................8
4.3 ELECTRICAL CHARACTERISTICS ..................................................................................................9
4.3.1 Driving for LCD panel signal processing board ........................................................................... 9
4.3.2 Working for backlight lamp........................................................................................................... 9
4.3.3 Power supply voltage ripple........................................................................................................ 10
4.3.4 Fuses............................................................................................................................................ 10
4.4 POWER SUPPLY VOLTAGE SEQUENCE.........................................................................................11
4.4.1 Sequence for LCD panel signal processing board........................................................................11
4.4.2 Sequence for backlight inverter (Option).....................................................................................11
4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS ........................................................ 12
4.5.1 LCD panel signal processing board ............................................................................................ 12
4.5.2 Backlight lamp ............................................................................................................................ 13
4.5.3 Positions of a plug and a socket .................................................................................................. 13
4.5.4 Connection between receiver and transmitter for LVDS............................................................. 14
4.6 DISPLAY COLORS AND INPUT DATA SIGNALS.......................................................................... 15
4.7 DISPLAY POSITIONS........................................................................................................................ 16
4.8 SCANNING DIRECTIONS ................................................................................................................ 16
4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD .......................... 17
4.9.1 Outline of input signal timings.................................................................................................... 17
4.9.2 Detailed input signal timing chart for DE mode ......................................................................... 17
4.9.3 Timing characteristics ................................................................................................................. 18
4.10 OPTICS.............................................................................................................................................. 19
4.10.1 Optical characteristics ............................................................................................................... 19
4.10.2 Definition of contrast ratio ........................................................................................................ 20
4.10.3 Definition of luminance uniformity........................................................................................... 20
4.10.4 Definition of response times...................................................................................................... 20
4.10.5 Definition of viewing angles..................................................................................................... 20
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 4
CONTENTS
5. RELIABILITY TESTS............................................................................................................................ 21
6. PRECAUTIONS....................................................................................................................................... 22
6.1 MEANING OF CAUTION SIGNS ..................................................................................................... 22
6.2 CAUTIONS ......................................................................................................................................... 22
6.3 ATTENTIONS...................................................................................................................................... 22
6.3.1 Handling of the product............................................................................................................... 22
6.3.2 Environment ................................................................................................................................ 22
6.3.3 Characteristics............................................................................................................................. 23
6.3.4 Other............................................................................................................................................ 23
7. OUTLINE DRAWINGS .......................................................................................................................... 24
7.1 FRONT VIEW ..................................................................................................................................... 24
7.2 REAR VIEW........................................................................................................................................ 25
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 5
1. OUTLINE
1.1 STRUCTURE AND PRINCIPLE
NL10276BC20-04 module is composed of the amorphous silicon thin film transistor liquid crystal
display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array
and a backlight unit.
The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT
array glass substrate and a color-filter glass substrate.
Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated
into best form for active matrix system by a signal processing board, and sent to the driver LSIs which
drive the individual TFT arrays.
The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight
assembly, when it is controlled by data signals. Color images are created by regulating the amount of
transmitted light through the TFT array of red, green and blue dots.
1.2 APPLICATIONS
• Display terminal for control system
• Industrial PC
1.3 FEATURES
• High luminance
• Wide viewing angle
• Extensive temperature
• 6-bit digital RGB signals
• Single link LVDS interface
• Reversible-scan direction
• Edge light type
• Replaceable lamp for backlight unit (Inverter less)
• Acquisition product for UL/c-UL (File number: E170632)
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 6
2. GENERAL SPECIFICATIONS
Display area 210.4 (W) × 157.8 (H) mm (typ.)
Diagonal size of display 26.3 cm (10.4 inches)
Drive system a-Si TFT active matrix
Display color 262,144 colors
Pixel 1,024 (H) × 768 (V) pixels
Pixel arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe
Dot pitch 0.0685 (W) × 0.2055 (H) mm
Pixel pitch 0.2055 (W) × 0.2055 (H) mm
Module size 243.0 (W) × 185.1 (H) × 11.0 (D) mm (typ.)
Weight 530 g (typ.)
Contrast ratio 300:1 (typ.)
Viewing angle At the contrast ratio 10:1
• Horizontal: Left side 60° (typ.), Right side 60° (typ.)
• Vertical: Up side 45° (typ.), Down side 60° (typ.)
Designed viewing direction At DPSR: normal scan
• Viewing direction without image reversal: up side (12 o'clock)
• Viewing direction with contrast peak: down side 5° to 10° (6 o'clock)
• Viewing angle with optimum grayscale (γ=2.2): normal axis
Polarizer surface Non matt treatment
Polarizer pencil-hardness 3H (min.) [by JIS K5400]
Color gamut At LCD panel center
40 % (typ.) [against NTSC color space]
Response time 15 ms (typ.)
Luminance At 5.0mArms / lamp
300 cd/m2 (typ.)
Signal system Single link LVDS (Receiver: THC63LVDF64A, THine Electronics Inc.)
[6-bit digital signals for data of RGB colors,
Dot clock (CLK), Data enable (DE)]
Power supply voltage LCD panel signal processing board: 3.3V
Backlight Edge light type: 2 cold cathode fluorescent lamps
Replaceable parts
• Lamps for backlight unit: Type No. 104LHS35
Recommended inverter (Option)
• Inverter: Type No. 104PW191
Power consumption At maximum luminance and checkered flag pattern
6.2W (typ.)
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 7
3. BLOCK DIAGRAM
Note1: GND and GNDB (Backlight inverter ground) should be connected together in customer equipment.
Note2: Neither FG (Frame ground) nor the metallic frame of lamp holder is connected to VBLC (Lamp low
voltage terminal).
Host
V-driver
3,072 lines
LCD panel
H: 1,024 × 3 (R,G,B)
V: 768
768 lines
VCC
GND
Power supply
for gradation
DC/DC
converter
LCD module (Product)
LCD panel signal processing board
V-driver
DA0+
+3.3V
DA0-
Controller with receiver for LVDS
DA1+
DA1-
DA2+
DA2-
CK+
CK-
100Ω
100Ω
100Ω
100Ω
DPSR
Fuse
Backlight inverter
(Option) VBLH
VBLH
GNDB
VBLC
Backlight unit (Edge light type)
N
ote1
Lamp
Lam
p
Metallic frame of lamp holder
N
ote2
H-driver
FG
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 8
Note3: Connections between GND, FG (Frame ground) and VBLC in the LCD module
GND - FG Not connected
GND - VBLC Not connected
FG - VBLC Not connected
4. DETAILED SPECIFICATIONS
4.1 MECHANICAL SPECIFICATIONS
Parameter Specification Unit
Module size 243.0 ± 0.5 (W) × 185.1 ± 0.5 (H) × 11.0 ± 0.5 (D) Note1 mm
Display area 210.4 ± 0.5 (W) × 157.8 ± 0.5 (H) Note1 mm
Weight 530 (typ.), 550 (max.) g
Note1: See "11. OUTLINE DRAWINGS".
4.2 ABSOLUTE MAXIMUM RATINGS
Parameter S
y
mbol Rating Unit Remarks
LCD panel signal board VCC -0.3 to +4.0 V
Hi
g
h volta
g
e side
(
Hot
)
Note1 VBLH 1,500 Vrms
Power supply
voltage Lamp Low volta
g
e side
(
Cold
)
Note2 VBLC 42.4 Vrms
Display signals
Note3 VD -0.3 to VCC+0.3 V
Input voltage
for signals Function signals
Note4 VF -0.3 to VCC+0.3 V
Ta = 25°C
Storage temperature Tst -20 to +70 °C
Front surface TopF 0 to +60 °C
Operating temperature
Rear surface TopR 0 to +60 °C
-
≤ 95 % Ta ≤ 40°C
≤ 85 % 40 < Ta ≤ 50°C
≤ 70 % 50 < Ta ≤ 55°C
Relative humidity
Note5 RH
≤ 60 % 55 < Ta ≤ 60°C
Absolute humidity
Note5 AH ≤ 78
Note6 g/m3Ta > 60°C
Note1: "VBLH" is the voltage value between low voltage terminal (Cold) and high voltage terminal (Hot).
Note2: "VBLC" is the voltage value between frame ground (FG) and low voltage terminal (Cold).
Note3: Display signals are DA0+/-, DA1+/-, DA2+/- and CK+/-. Also controller with LVDS receiver
are worked by +3.3V from DC/DC converter.
Note4: Function signal is DPSR.
Note5: No condensation
Note6: Ta = 60°C, RH = 60%
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 9
4.3 ELECTRICAL CHARACTERISTICS
4.3.1 Driving for LCD panel signal processing board
(Ta = 25°C)
Parameter Symbol Min. Typ. Max. Unit Remarks
Power supply voltage VCC 3.0 3.3 3.6 V -
Power supply current ICC - 300 Note1 500 Note2 mA VCC = 3.3V
Low VDRL 0 - 0.8 V
Input voltage for LVDS
receiver High VDRH 2.0 - 2.4 V -
Low VTL -100 - - mV
Differential input threshold
voltage for LVDS receiver High VTH - - +100 mV
VOC=1.2V
Note3
Low VFDL 0 - 0.8 V
Input voltage for DPSR
signal High VFDH 2.0 - VCC V -
Note1: Checkered flag pattern (by EIAJ ED-2522)
Note2: Pattern for maximum current
Note3: Common mode voltage for LVDS receiver
4.3.2 Working for backlight lamp
Parameter Symbol Ta Min. Typ. Max. Unit Remarks
0°C1,100 - - Vrms
Starting voltage VS 25°C850 - - Vrms Note1
Power supply voltage VBLH 25°C- 520 - Vrms Note1,Note2
Power supply current IBL 25°C2.0 5.0 5.5 mArms Note2, Note3
Oscillation frequency FO 25°C60 65 70 kHz Note4
Note1: The power supply voltage cycle between lamps should be kept on a same phase. "VS" and
"VBLH" are the voltage value between low voltage side (Cold) and high voltage side (Hot).
Note2: The asymmetric ratio of working waveform for lamps (Power supply voltage peak ratio,
power supply current peak ratio and waveform space ratio) should be less than 5 % (See the
following figure.). If the waveform is asymmetric, DC (Direct current) element apply into
the lamp. In this case, a lamp lifetime may be shortened, because a distribution of a lamp
enclosure substance inclines toward one side between low voltage terminal (Cold terminal)
and high voltage terminal (Hot terminal).
Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative
Sa: Waveform space for positive part, Sb: Waveform space for negative part
Note3: The lamp holder of this product contains two backlight lamps. The low voltage terminal of
both lamps is connected to one contact point. Also above power supply current specification
is one lamp duty. Therefore, this lamp holder becomes twice as many power supply current
as above value on low voltage (Cold) line. The measurement for the power supply current
value of one lamp should measure on high voltage (Hot) line to each lamp.
Note4: In case "FO" is not the recommended value, beat noise may display on the screen, because
of interference between "FO" and "1/th". Recommended value of "FO" is as following.
th: Horizontal synchronous cycle (See "4.9.3 Timing characteristics".)
n: Natural number (1, 2, 3 ⋅⋅⋅⋅⋅⋅⋅⋅)
FO =1
4
1
th
××(2n-1)
Pa
Pb
Sa
Sb
0
Pa - Pb
Pb × 100 ≤ 5 %
Sa - Sb
Sb × 100 ≤ 5 %
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 10
4.3.3 Power supply voltage ripple
This product works, even if the ripple voltage levels are beyond the permissible values as following
the table, but there might be noise on the display image.
Parameter Power supply voltage Ripple voltage Note1
(Measure at input terminal of power supply) Unit
VCC 3.3 V ≤ 100 mVp-p
Note1: The permissible ripple voltage includes spike noise.
4.3.4 Fuses
Fuse
Fusing line Type Supplier Rating Fusing current
Note1
2.0 A
VCC TF16N2.00 KOA Corporation
47 V
4.0 A
Note1: The power supply capacity should be more than the fusing current. If the power supply
capacity is less than the fusing current, the fuse may not blow for a short time, and then
nasty smell, smoking and so on may occur.
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 11
4.4 POWER SUPPLY VOLTAGE SEQUENCE
4.4.1 Sequence for LCD panel signal processing board
Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V, a
protection circuit may work, and then this product may not work.
Note2: Display (DA0+/-, DA1+/-, DA2+/- and CK+/-) with 100Ω (Characteristic impedance) and
function (DPSR) signals must be Low or High-impedance, exclude the VALID period (See
above sequence diagram), in order to avoid that internal circuits is damaged.
If some of display and function signals of this product are cut while this product is
working, even if the signal input to it once again, it might not work normally. If customer
stops the display and function signals, they should be cut VCC.
4.4.2 Sequence for backlight inverter (Option)
Note1: These are display and function signals for LCD panel signal processing board.
Note2: The backlight inverter voltage (VDDB) should be inputted within the valid period of
display and function signals, in order to avoid unstable data display.
VALID period
OFF
0ms < t < 35ms 0ms < t < 35ms
ON
3.0V
0V
Tr < 50ms
VCC
N
ote1
Display and
function signals
Note2
Toff > 100ms
Display and
function signals
Note1
VDDB
VALID period
N
ote2
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 12
4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS
4.5.1 LCD panel signal processing board
CN1 socket (Module side): FI-SE20P-HF (Japan Aviation Electronics Industry Limited)
Adaptable plug: FI-S20S (Japan Aviation Electronics Industry Limited)
Pin No. Symbol Function Remarks
1GND
2GND
Ground -
3 DPSR Select of scan direction Normal scan: Low or Open, Reverse scan: High Note1
4 NC Non connection
5 GND Ground
-
6CK+
7CK-
Pixel clock Note2
8 GND Ground -
9D2+
10 D2-
Pixel data Note2
11 GND Ground -
12 D1+
13 D1-
Pixel data Note2
14 GND Ground -
15 D0+
16 D0-
Pixel data Note2
17 GND
18 GND
Ground
19 VCC
20 VCC
Power supply
-
Note1: See "4.8 SCANNING DIRECTIONS".
Note2: Twist pair wires with 100Ω (Characteristic impedance) should be connected between LCD
panel signal processing board and LVDS transmitter.
✩
CN1: Figure of socket
20 19 18 17 4 3 21
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 13
4.5.2 Backlight lamp
CN2 plug: BHR-03VS-1 (J.S.T Mfg. Co., Ltd.)
Adaptable socket: SM03 (4.0) B-BHS-TB (J.S.T Mfg. Co., Ltd.)
Pin No. Symbol Signal Remarks
1 VBLC Low voltage (Cold)
2 VBLH High voltage (Hot)
3 VBLH High voltage (Hot)
-
4.5.3 Positions of a plug and a socket
CN2: Figure of plug
1 3
✩
CN1
1
20
Barcode label
N
ame plate
CN2
Caution label
Low voltage (Cold)
High voltage (Hot)
1
3
Insert direction
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 14
4.5.4 Connection between receiver and transmitter for LVDS
Note1: Recommended transmitter
See the data sheet for THC63LVDM63A (THein Electronics Inc.).
R0
R1
R2
R3
R4
R5
G0
G1
G2
G3
G4
G5
B0
B1
B2
B3
B4
B5
DE
CLK
VCC (+3.0V)
VCC (+5.0V)
GND
ViFD
GND
GND
DPSR
NC
GND
CK+
CK-
GND
D2+
D2-
GND
D1+
D1-
GND
D0+
D0-
GND
GND
VCC
VCC
TA0
TA1
TA2
TA3
TA4
TA5
TA6
TB0
TB1
TB2
TB3
TB4
TB5
TB6
TC0
TC1
TC2
TC3
TC6
CLK IN
VCC
TCLK+
TCLK-
TC+
TC-
TB+
TB-
TA+
TA-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
GND
Transmitter for LVDS
THC63LVDM63A
Note1
Socket
CN1
DC/DC
converter
LCD panel signal processing board
Panel driver
Panel driver
Host LCD module (Product)
GND
RCLK+
RCLK-
RC+
RC-
RB+
RB-
RA+
RA-
LCD controller
Receiver for LVDS
Equivalent of
THC63LVDF64A
GND
Signal
processor
VCC
DPSH
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 15
4.6 DISPLAY COLORS AND INPUT DATA SIGNALS
This product can display in equivalent to 262,144 colors in 64 scale. Also the relation between
display colors and input data signals is as the following table.
Data signal (0: Low level, 1: High level)
Display colors R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Basic colors
Black
Blue
Red
Magenta
Green
Cyan
Yellow
White
000000
000000
111111
111111
000000
000000
111111
111111
000000
000000
000000
000000
111111
111111
111111
111111
000000
111111
000000
111111
000000
111111
000000
111111
Red scale
Black
dark
↑
↓
bright
Red
000000
000001
000010
:
:
111101
111110
111111
000000
000000
000000
:
:
000000
000000
000000
000000
000000
000000
:
:
000000
000000
000000
Green scale
Black
dark
↑
↓
bright
Green
000000
000000
000000
:
:
000000
000000
000000
000000
000001
000010
:
:
111101
111110
111111
000000
000000
000000
:
:
000000
000000
000000
Blue scale
Black
dark
↑
↓
bright
Blue
000000
000000
000000
:
:
000000
000000
000000
000000
000000
000000
:
:
000000
000000
000000
000000
000001
000010
:
:
111101
111110
111111
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 16
4.7 DISPLAY POSITIONS
The following table is the coordinates per pixel (See figure of "4.8 SCANNING DIRECTIONS".).
C( 0, 0) C( 1, 0) • • •C( X, 0) • • •C(1022, 0) C(1023, 0)
C( 0, 1) C( 1, 1) • • •C( X, 1) • • •C(1022, 1) C(1023, 1)
•
•
•
•
•
•
•
• • •
•
•
•
•
•
• • •
•
•
•
•
•
• • •
•
C( 0, Y) C( 1, Y) • • •C( X, Y) • • •C(1022, Y) C(1023, Y)
•
•
•
•
•
•
•
• • •
•
•
•
•
•
• • •
•
•
•
•
•
•
•
C( 0, 766) C( 0, 766) • • •C( X, 766) • • •C(1022, 766) C(1023, 766)
C( 0, 767) C( 1, 767) • • •C( X, 767) • • •C(1022, 767) C(1023, 767)
4.8 SCANNING DIRECTIONS
The following figures are seen from a front view. Also the arrow shows the direction of scan.
Note1: Meaning of C (X, Y) and D (X, Y)
C (X, Y): The coordinates of the display position (See "4.7 DISPLAY POSITIONS".)
D (X, Y): The data number of input signal for LCD panel signal processing board
Figure 1. Normal scan (DPSR: Low or Open)
C (0,0)
D (0,0)
C (0,767)
D (0,767)
C (1023,767)
D (1023,767)
C (1023,0)
D (1023,0)
Figure 2. Reverse scan (DPSR: High)
C (0,0)
D (1023,767)
C (0,767)
D (1023,0)
C (1023,767)
D (0,0)
C (1023,0)
D (0,767)
N
ote1
N
ote1
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 17
4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD
4.9.1 Outline of input signal timings
• Horizontal signal
Note1: This diagram indicates virtual signal for set up to timing.
• Vertical signal
Note1: This diagram indicates virtual signal for set up to timing.
Note2: See "4.9.2 Detailed input signal timing chart for DE mode" for numeration of pulse.
4.9.2 Detailed input signal timing chart for DE mode
• Outline chart
Note1: X is data number from 1 to 1022. See "4.8 SCANNING DIRECTIONS".
Display period
Note1
Horizontal display period (thd)
Data enable
(DE mode)
Vertical display period (tvd)
1234 768
Display period
Note1
Data enable
(DE mode)
N
ote2
DE
VDRH
0.5VCC
VDRL
CLK
VDRH
VDRL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
tdes
tdeh
tdrf
tdrf
tds
tdh
tcrf
tcr
f
tch
tc
1024
D (0, 0) D (1023, 0)
768
1
D (X, 0)
thd
tv
d
A
X+1
tdes
tder
tderf
Note1
1
2
D (X, 2)D (0, 2) D (1023, 2)
1344 (typ.)
tdeh
1025
D (X, 767)D (0, 767) D (1023, 767)
VDRH
0.5VCC
VDRL
t
v
th
N
ote1
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 18
• Detail of A part
Note1: X is data number from 1 to 1022. See "4.8 SCANNING DIRECTIONS".
4.9.3 Timing characteristics
Parameter Note1 Symbol Min. Typ. Max. Unit Remarks
Frequency (LVDS receiver) tcf 60.0 65.0 68.0 MHz 15.4 ns (typ.) Note1
Duty tcd - - - - Note1, Note2
CLK
Rise time, Fall time tcrf - - - -
Setup time tds - - - -
CLK-DATA Hold time tdh - - - -
DATA
Rise time, Fall time tdrf - - - -
Note2
Cycle th - 1,344 - CLK Note1, Note3
Horizontal Display period thd 1,024 CLK
Cycle tv - 806 - H
Vertical
(One frame) Display period tvd 768 H
Note1
Setup time tdes - - - -
CLK-DE Hold time tdeh - - - -
DE
Rise time, Fall time tderf - - - -
Note2
Note1: Definition of parameters is as follows.
tcf = 1/tc, tcd = tch/tc = tch×tcf, tc = 1CLK, th = 1H
Note2: See the data sheet of LVDS transmitter.
Note3: "th" must keep the fluctuation within ±1 CLK, because of avoidance of image sticking.
VDRH
0.5VCC
VDRL
CLK
tds tdh
tdrf
tdrf
tc
tcrf
tderf
VDRH
VDRL
DATA
(R0 to R5)
(G0 to G5)
(B0 to B5)
DE
tch
tcrf
tdeh tdes
tderf
tdeh tdes
VDRH
VDRL
D (0, 0) D (X, 0) D (1023, 0)
1X+1 1024 1025
N
ote1
N
ote1
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 19
4.10 OPTICS
4.10.1 Optical characteristics
Parameter Note1 Condition Symbol Min. Typ. Max. Unit Remarks
Contrast ratio White/Black at center
θR = 0°, θL = 0°, θU= 0°, θD= 0°CR 150 300 - - Note2
Luminance White at center
θR = 0°, θL = 0°, θU= 0°, θD= 0°L 240 300 - cd/m2-
Luminance uniformity - LU - 1.24 1.40 - Note3
x coordinate Wx -0.315 - -
White y coordinate Wy -0.340 - -
x coordinate Rx -0.575 --
Red y coordinate Ry -0.335 --
x coordinate Gx -0.332 --
Green y coordinate Gy -0.536 --
x coordinate Bx -0.153 --
Chromaticity
Blue y coordinate By -0.150 --
Color gamut θR = 0°, θL = 0°, θU= 0°, θD= 0°
at center, against NTSC color space C3540 -%
Note4
White to black Ton - 15 30 ms
Response time
Black to white Toff - 40 60 ms
Note5
Note6
Right θU = 0°, θD = 0°, CR = 10 θR-60 -°
Left θU = 0°, θD = 0°, CR = 10 θL-60 -°
Up θR = 0°, θL = 0°, CR = 10 θU-45 -°
Viewing angle
Down θR = 0°, θL = 0°, CR = 10 θD-60 -°
Note7
Note1: Measurement conditions are as follows.
Ta = 25°C, VCC = 3.3V, IBL = 5.0mArms/lamp, Display mode: XGA-60Hz
Optical characteristics are measured at luminance saturation after 20minutes from working
the product, in the dark room. Also measurement method for luminance is as follows.
Note2: See "4.10.2 Definition of contrast ratio".
Note3: See "4.10.3 Definition of luminance uniformity".
Note4: These coordinates are found on CIE 1931 chromaticity diagram.
Note5: Product surface temperature: TopF = 25°C
Note6: See "4.10.4 Definition of response times".
Note7: See "4.10.5 Definition of viewing angles".
1°
Photodetector (TOPCON BM-5A)
LCD module
(Product)
50cm
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 20
4.10.2 Definition of contrast ratio
The contrast ratio is calculated by using the following formula.
Luminance of white screen
Luminance of black screen
4.10.3 Definition of luminance uniformity
The luminance uniformity is calculated by using following formula.
Maximum luminance from ①
①①
① to ⑤
⑤⑤
⑤
Minimum luminance from ①
①①
① to ⑤
⑤⑤
⑤
The luminance is measured at near the 5 points shown below.
4.10.4 Definition of response times
Response time is measured, the luminance changes from "white" to "black", or "black" to "white" on
the same screen point, by photo-detector. Ton is the time it takes the luminance change from 90%
down to 10%. Also Toff is the time it takes the luminance change from 10% up to 90% (See the
following diagram.).
4.10.5 Definition of viewing angles
①
①①
①②
②②
②
③
③③
③
④
④④
④⑤
⑤⑤
⑤
171 512 853
126
384
640
Contrast ratio (CR) =
Luminance uniformity (LU) =
Left Upper
Lower
N
ormal axis (Perpendicular)
θU
θD
θR
θL12 o’clock
Right
100%
90%
10%
0%
Ton Toff
Luminance
White
Black
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 21
5. RELIABILITY TESTS
Test item Condition Judgement
High temperature and humidity
(Operation)
① 55 ± 2°C, RH = 85%, 240hours
② Display data is black.
High temperature
(Operation)
① 60 ± 2°C, 240hours
② Display data is black.
Heat cycle
(Operation)
① 0 ± 3°C…1hour
60 ± 3°C…1hour
② 50cycles, 4hours/cycle
③ Display data is black.
Thermal shock
(Non operation)
① -20 ± 3°C…30minutes
70 ± 3°C…30minutes
② 100cycles, 1hour/cycle
③ Temperature transition time is within 5
minutes.
ESD
(Operation)
① 150pF, 150Ω, ±10kV
② 9 places on a panel surface Note2
③ 10 times each places at 1 sec interval
Dust
(Operation)
① Sample dust: No. 15 (by JIS-Z8901)
② 15 seconds stir
③ 8 times repeat at 1 hour interval
No display malfunctions Note1
Vibration
(Non operation)
① 5 to 100Hz, 11.76m/s2
② 1 minute/cycle
③ X, Y, Z direction
④ 120 times each directions
Mechanical shock
(Non operation)
① 539m/ s2, 11ms
② ±X, ±Y, ±Z direction
③ 5 times each directions
No display malfunctions Note1
No physical damages
Note1: Display functions are checked under the same conditions as product inspection.
Note2: See the following figure for discharge points.
¡¡
¡
¡¡
¡
¡¡
¡
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 22
6. PRECAUTIONS
6.1 MEANING OF CAUTION SIGNS
The following caution signs have very important meaning. Be sure to read "6.2 CAUTIONS", after
understanding this contents!
This sign has the meaning that customer will be injured by himself, if customer has
wrong operations.
6.2 CAUTIONS
∗
∗∗
∗ Pay attention to burn injury for the working backlight! It may be over 35°
°°
°C from
ambient temperature.
∗
∗∗
∗ Do not shock and press the LCD panel and the backlight! Danger of breaking, because
they are made of glass. (Shock: To be not greater 539m/s2 and to be not greater 11ms,
Pressure: To be not greater 19.6N)
6.3 ATTENTIONS
6.3.1 Handling of the product
① Take hold of both ends without touch the circuit board when customer pulls out products (LCD
modules) from inner packing box. If customer touches it, products may be broken down or out of
adjustment, because of stress to mounting parts.
② Do not hook cables nor pull connection cables such as flexible cable and so on, for fear of damage.
③ If customer puts down the product temporarily, the product puts on flat subsoil as a display side
turns down.
④ Take the measures of electrostatic discharge such as earth band, ionic shower and so on, when
customer deals with the product, because products may be damaged by electrostatic.
⑤ The torque for mounting screws must never exceed 0.29N⋅m. Higher torque values might result in
distortion of the bezel.
⑥ Do not press or rub on the sensitive display surface. If customer clean on the panel surface, NEC
Corporation recommends using the cloth with ethanolic liquid such as screen cleaner for LCD.
⑦ Do not push-pull the interface connectors while the product is working, because wrong power
sequence may break down the product.
6.3.2 Environment
① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive
gases. Keep the product in antistatic pouch in room temperature, because of avoidance for dusts
and sunlight, if customer stores the product.
② Do not operate in high magnetic field. Circuit boards may be broken down by it.
③ Use an original protection sheet on the product surface (polarizer). Adhesive type protection sheet
should be avoided, because it may change color or properties of the polarizer.
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 23
6.3.3 Characteristics
The following items are neither defects nor failures.
① Response time, luminance and color may be changed by ambient temperature.
② The LCD may be seemed luminance non-uniformity, flicker, vertical seam or small spot by display
patterns.
③ Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change
depending on operating time, and especially low temperature, because the LCD has cold cathode
fluorescent lamps.
④ Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen
saver, if the fixed pattern is displayed on the screen.
⑤ The display color may be changed by viewing angle because of the use of condenser sheet in the
backlight unit.
⑥ Optical characteristics may be changed by input signal timings.
⑦ The interference noise of input signal frequency for this product's signal processing board and
luminance control frequency of customer's backlight inverter may appear on a display. Set up
luminance control frequency of backlight inverter so that the interference noise does not appear.
6.3.4 Other
① All GND, backlight inverter ground (GNDB), VCC and backlight inverter power supply voltage
(VDDB) terminals should be used without a non-connected line.
② Do not disassemble a product or adjust volume without permission of NEC Corporation.
③ See "REPLACEMENT MANUAL FOR LAMPHOLDER", if customer would like to replace
backlight lamps.
④ Pay attention not to insert waste materials inside of products, if customer uses screwnails.
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 24
7. OUTLINE DRAWINGS
7.1 FRONT VIEW
Unit: mm
243 .0
+0 .5
-0 .5
235 .0
+0 .3
-0 .3
215 .4
+0 .3
-0 .3
(BEZE L OPEN ING AREA )
210 .4
+0 .5
-0 .5
(AC T IVE AREA )
17 .0
+0 .3
-0 .3
14 .6
+0 .3
-0 .3
5.3
+0 .3
-0 .3
2.8
+0 .2
-0 .2
185 .1
+0 .5
-0 .5
166 .6
+0 .3
-0 .3
2.8
+0 .2
-0 .2
5.3
+0 .3
-0 .3
4-CPIMS*M2*L4
2-
φ
3.5
10 .5
+0 .5
-0 .5
MODU LE CEN TER
ACT IVE AREA CENTER
2.8
+0 .2
-0 .2
5.3
+0 .3
-0 .3
132 .6
+0 .3
-0 .3
157 .8
+0 .5
-0 .5
(ACT IVE AREA )
161 .8
+0 .5
-0 .5
(BEZEL OPEN ING AREA )
2-R1.75
5.3
+0 .3
-0 .3
2.8
+0 .2
-0 .2
11 .0
+0 .5
-0 .5
10 .1
+0 .5
-0 .5
6.7
+0 .5
-0 .5
5.7
+0 .5
-0 .5
5.1
+0 .5
-0 .5
29 .4
+0 .5
-0 .5
12 .6
+0 .5
-0 .5
2.9
+0 .5
-0 .5
3.9
+0 .5
-0 .5
9.7
+0 .5
-0 .5
7.2
+0 .3
-0 .3
4.8
+0 .5
-0 .5
8.1
+0 .5
-0 .5
4.7
+0 .5
-0 .5
1.8
+0 .5
-0 .5
3.2
+0 . 5
-0 .5
4.7
+0 .5
-0 .5
8.1
+0 .5
-0 .5
3.9
+0 .5
-0 .5
2.9
+0 .5
-0 .5
5.1
+0 .5
-0 .5
5.7
+0 .5
-0 .5
2.8
+0 . 5
-0 . 5
4.0
+0 .5
-0 .5
NL10276BC20-04
DATA SHEET EN0555EJ4V1DS00 25
7.2 REAR VIEW
Unit: mm
60 .0
+10 .0
-10 .0
H IGH VO L TAGE
CAUT ION
POWE R BE FOR E SER V I CE .
R ISK 0 F E LEC TR IC SHOCK .
D ISCONNECT THE E LECTR IC
**
******
THE T FT CO LOR L CD
PANEL CONTA INS CO LD CATHODE
F LOURESCENT LAMPS . P LEASE
FO L LOW LOCA L ORD INANCES
OR REGU LAT IONS FOR ITS
DISPOSAL
****** *********
****** ********** **
****** **********
****** **
************
6.8
+0 .5
-0 .5
8.0
+0 .5
-0 .5
3.4
+0 .5
-0 .5
4.5
+0 .5
-0 .5
5.6
+0 .5
-0 .5
2.4
+0 .5
-0 .5
5.3
+0 .5
-0 .5
5.0
+0 .5
-0 .5
130 .2
+0 .5
-0 .5
6.6
+0 .5
-0 .5
2.4
+0 .5
-0 .5
5.3
+0 .5
-0 .5
5.0
+0 .5
-0 .5
10 .2
+0 .5
-0 .5
9.2
+0 .5
-0 .5
32 .2
+0 .5
-0 .5
40 .3
+0 .5
-0 .5
3.4
+0 .5
-0 .5
4.5
+0 .5
-0 .5
8.0
+0 .5
-0 .5
6.8
+0 .5
-0 .5
NL10276BC20 -04
MADE IN JAPAN
** .** .**
US
C
SER I A L :
*************
********
MOD E L :
R
E170632
PANE L :