For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
1
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Functional Diagram
The HMC898LP4E is a MMIC band pass lter which
features a user selectable passband frequency. The
3 dB lter bandwidth is approximately 17%. The 20
dB lter bandwidth is approximately 35%. The center
frequency can be varied between 11.5 and 21.5
GHz by applying an analog tune voltage between 0
and 14V. This tunable lter can be used as a much
smaller alternative to physically large switched lter
banks and cavity tuned lters. The HMC898LP4E has
excellent microphonics due to the monolithic design,
and provides a dynamically adjustable solution in
advanced communications applications.
Typical Applications Features
General Description
The HMC898LP4E is ideal for:
• Test & Measurement Equipment
• Military RADAR & EW/ECM
• SATCOM & Space
• Industrial & Medical Equipment
Fast Tuning Response
Excellent Wideband Rejection
Single Chip Replacement
for Mechanically Tuned Designs
24 Lead 4x4 mm SMT Package
Electrical Specications, TA = +25 °C
Parameter Min. Ty p . Max. Units
Fcenter Tuning Range 11. 5 21.5 GHz
3 dB Bandwidth 17 %
Low Side Rejection Frequency (Rejection >20 dB) 0.81 *Fcenter GHz
High Side Rejection Frequency (Rejection >20 dB) 1.16 *Fcenter GHz
Low Side Sub-Harmonic Rejection (Rejection >40 dB) 0.55 *Fcenter GHz
High Side Sub-Harmonic Rejection (Rejection >40 dB) 1.27 *Fcenter GHz
Re-entry Frequency (Rejection <30 dB) >40 GHz
Insertion Loss 6 dB
Return Loss (2 dB Bandwidth) 9 dB
Input IP3 (Pin = 0 to +15 dBm) 29 dBm
Input Power @ 5° Shift In Insertion Phase (Vfctl = 0V) 9 dBm
Input Power @ 5° Shift In Insertion Phase (Vfctl = 1V) 14 dBm
Frequency Control Voltage (Vfctl)014 V
Source/Sink Current (Ifctl)±1 mA
Residual Phase Noise [1] (100 kHz Offset) -157 dBc/Hz
Fcenter Drift Rate - 1.9 MHz/°C
Tuning Speed, Phase Settling to within 10° [2] < 200 ns
[1] Optimum residual phase noise performance requires the use of a low noise driver circuit.
[2] Tuning speed includes 40 ns tuning voltage ramp from driver.
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
2
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Broadband Insertion Loss vs. Vfctl
Insertion Loss vs. Vfctl
Insertion Loss vs. Temperature, Vfctl = 7V
Broadband Return Loss vs. Vfctl
Return Loss vs. Vfctl
Return Loss vs. Temperature, Vfctl = 7V
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
0 5 10 15 20 25 30 35 40
0V
3V
7V
14V
INSERTION LOSS (dB)
FREQUENCY (GHz)
-35
-30
-25
-20
-15
-10
-5
0
0 5 10 15 20 25 30 35 40
S11_0V
S22_0V
S11_7V
S22_7V
S11_14V
S22_14V
RETURN LOSS (dB)
FREQUENCY (GHz)
-18
-16
-14
-12
-10
-8
-6
-4
-2
0
8 10 12 14 16 18 20 22 24 26 28
0V
3V
7V
14V
INSERTION LOSS (dB)
FREQUENCY (GHz)
-35
-30
-25
-20
-15
-10
-5
0
8 10 12 14 16 18 20 22 24 26 28
S11_0V
S22_0V
S11_7V
S22_7V
S11_14V
S22_14V
RETURN LOSS (dB)
FREQUENCY (GHz)
-18
-16
-14
-12
-10
-8
-6
-4
-2
0
14 15 16 17 18 19 20 21 22
+25C
+85C
-40C
INSERTION LOSS (dB)
FREQUENCY (GHz)
-40
-35
-30
-25
-20
-15
-10
-5
0
14 15 16 17 18 19 20 21 22
+25C_S11
+25C_S22
+85C_S11
+85C_S22
-40C_S11
-40C_S22
RETURN LOSS (dB)
FREQUENCY (GHz)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
3
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Center Frequency vs. Temperature Insertion Loss vs. Temperature
Return Loss in a 2 dB Bandwidth
vs. Temperature
Low Side Rejection Ratio vs.
Temperature [1]
High Side Rejection Ratio vs.
Temperature [1]
3 dB Bandwidth vs. Temperature
[1] Rejection ratio is dened as the ratio of the frequency at which the relative insertion loss is 20 dB to ƒcenter
8
10
12
14
16
18
20
22
24
0 2 4 6 8 10 12 14
+25C
+85C
-40C
CENTER FREQUENCY (GHz)
Vfctl (Vdc)
-16
-14
-12
-10
-8
-6
-4
-2
0
0 2 4 6 8 10 12 14
+25C
+85C
-40C
INSERTION LOSS (dB)
Vfctl (Vdc)
14
15
16
17
18
19
20
0 2 4 6 8 10 12 14
+25C
+85C
-40C
BANDWIDTH (%)
Vfctl (Vdc)
-14
-12
-10
-8
-6
-4
-2
0
0 2 4 6 8 10 12 14
+25C
+85C
-40C
RETURN LOSS (dB)
Vfctl (Vdc)
0.7
0.75
0.8
0.85
0.9
0 2 4 6 8 10 12 14
+25C
+85C
-40C
F20dB TO Fcenter RATIO
Vfctl (Vdc)
1.05
1.1
1.15
1.2
1.25
0 2 4 6 8 10 12 14
+25C
+85C
-40C
F20dB To Fcenter RATIO
Vfctl (Vdc)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
4
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Tuning Sensitivity vs. Temperature
Group Delay vs. Fcenter vs. Temperature Input IP3 vs. Temperature
Phase Sensitivity vs. Vfctl
Group Delay vs. Frequency
Residual Phase Noise
0
200
400
600
800
1000
1200
1400
1600
1 2 3 4 5 6 7 8 9 10 11 12 13 14
+25C
+85C
-40C
SENSITIVITY (MHz/V)
Vfctl (Vdc)
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
4 6 8 10 12 14 16 18 20 22 24 26 28 30
0V
2V
7V
14V
FREQUENCY (GHz)
GROUP DELAY (ns)
0.3
0.4
0.5
0.6
0.7
0 2 4 6 8 10 12 14
+ 25C
+ 85C
- 40C
GROUP DELAY (nS)
Vfctl (Vdc)
10
15
20
25
30
35
1 2 3 4 5 6 7 8 9 10 11 12 13 14
+ 25C
+ 85C
- 40C
INPUT IP3 (dBm)
Vfctl (Vdc)
-170
-160
-150
-140
-130
-120
102103104105106107
+ 1V
+ 7V
+ 14V
RESIDUAL PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
8
10
12
14
16
18
20
22
24
0
1
2
3
4
5
6
7
8
0 2 4 6 8 10 12 14
APPROXIMATE Fcenter (GHz)
DELTA PHI (RAD/V)
Vfctl (Vdc)
Delta Phi
Approximate
Fcenter
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
5
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Absolute Maximum Ratings Reliability Information
Frequency Control Voltage (Vfctl) -0.5 to +15V
RF Power Input 27 dBm
Storage Temperature -65 to +150 °C
ESD Sensitivity (HBM) Class 1 A
Junction Temperature to Maintain
1 Million Hour MTTF 150 °C
Nominal Junction Temperature
(T= 85 °C and Pin = 27 dBm) 103 °C
Operating Temperature -40 to +85 °C
Fcenter vs. Input PowerInsertion Phase vs. Input Power
-40
-35
-30
-25
-20
-15
-10
-5
0
0 2 4 6 8 10 12 14 16 18 20
0V
1V
7V
10V
14V
PHASE (DEGREES)
INPUT POWER (dBm)
-180
-160
-140
-120
-100
-80
-60
-40
-20
0
0 2 4 6 8 10 12 14 16 18 20
0V
1V
7V
10V
14V
FREQUENCY (MHz)
INPUT POWER (dBm)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
6
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. Pin BURR LENGTH SHALL BE 0.15 mm MAXIMUM.
Pin BURR HEIGHT SHALL BE 0.05 mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05 mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Part Number Package Body Material Lead Finish MSL Rating Package Marking [1]
HMC898LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] H898
XXXX
[1] 4-Digit lot number XXXX
[2] Max peak reow temperature of 260 °C
Package Information
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
7
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Pin Descriptions
Application Circuit
Pin Number Function Description Interface Schematic
1, 2, 4 - 7, 12 - 15,
17 - 19, 24 GND These pins and exposed paddle
must be connected to RF/DC ground.
8, 10, 11, 20 - 23 NC
The pins are not connected internally; however, all data
shown herein was measured with these pins connected to
RF/DC ground externally.
3RFIN This pin is AC coupled and
matched to 50 Ohms.
9Vfctl Center frequency control voltage.
16 RFOUT This pin is AC coupled and
matched to 50 Ohms.
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FILTERS - TUNABLE - SMT
8
HMC898LP4E
v00.0511
FILTER - TUNABLE, BAND PASS SMT
11.5 - 21.5 GHz
Evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohms impedance while the package
ground leads and exposed paddle should be con-
nected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
List of Materials for Evaluation PCB 131086 [1]
Item Description
J1, J2 Connector, 2.9 mm, Female
J6, J8 DC Pin
C2 100 pF Capacitor, 0402 Pkg.
U1 HMC898LP4E Filter - Tunable
PCB [2] 130746 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25FR or Rogers 25FR
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
HMC898LP4E 131086-HMC898LP4E HMC898LP4ETR HMC898LP4E-AN HMC898LP4ETR-AN