VACUUMSCHMELZE
SPECIFICATION
Item no.:
T60404-N4646-X200
K-No.:
25150 125 A Current Sensor
Date:
20.10.2010
Customer:
Standard type
Customers Part no.:
Page 1 of 2
Hrsg.: KB-E
editor Bearb:
designer
Le. KB-PM: KRe
check freig.: prs.
released
Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden
Any offenders are liable to pay all relevant damages.
For the electronic measurement of currents:
DC, AC, pulsed, mixed ..., with a galvanic isolation
between the primary circuit (high power)
and the secondary circuit (electronic circuit)
Description
Closed loop (compensation)
Current Sensor with magnetic
field probe
Printed circuit board mounting
Casing and materials UL-listed
Characteristics
Excellent accuracy
Very low offset current
Very low temperature dependency and offset
current drift
Very low hysteresis of offset current
Short response time
Wide frequency bandwidth
Compact design
Reduced offset ripple
Applications
Mainly used for stationary operation in industrial
applications:
AC variabel speed drives and servo motor
drives
Static converters for for DC motor drives
Battery supplied applications
Switched Mode Power Supplies (SMPS)
Power Supplies for welding applications
Uninterruptable Power Supllies (UPS)
Electrical data Ratings
IPN Primary nominal r.m.s. current 125 A
R
M
Measuring resistance VC=± 12V 5 ... 250
VC=± 15V 18400
ISN Secondary nominal r.m.s. current 125 mA
K
N
Turns ratio 1: 1000
Accuracy Dynamic performance data min. typ. max. Unit
I
P,max Max. measuring range
@ VC = ±12V, RM = 14 (tmax = 10sec) ±201 A
@ VC = ±15V, RM = 25 (tmax = 10sec) ±214 A
X Accuracy @ IPN, TA= 25°C 0.1 0.5 %
ε
L
Linearity 0.1 %
I
0
Offset current @ IP=0, TA= 25°C 0.03 0.1 mA
tr Response time 1 µs
Δt (IP,max) Delay time at di/dt = 100 A/µs 0.5 µs
f Frequency bandwidth DC...100 kHz
General data min. typ. max. Unit
TA Ambient operating temperature -40 +85 °C
T
S
Ambient storage temperature -40 +90 °C
m Mass 30 g
V
C
Supply voltage ±11.4 ±12/±15 ±15.75 V
IC Current consumption 18 mA
Constructed and manufactored and tested in accordance with EN 61800-5-1 (Pin 1- 4 to inner hole)
Reinforced insulation, Insulation material group 1, Pollution degree 2
Sclear Clearance (component without solder pad) 12 mm
S
creep Creepage (component without solder pad) 12 mm
Vsys System voltage overvoltage category 3 RMS 600 V
V
work Working voltage (table 7 acc. to EN61800-5-1)
Over voltage category 2 RMS 1000 V
U
PD Rated discharge voltage peak value 1225 V
Maximal continuous and peak currents at defined temperatures
Supply voltage ±12V: Supply voltage ±15V:
Date Name Isue Amendment
20.10.10 Le 81 Mechanical outline Error correction distance of fastening bores (41,4 to 40,64) lapidary change.
T
A
85 °C 55 °C
IP 100 A 150 A
IP,max 224 A 262 A
R
M
1
0
5
70 °C
130 A
255 A
5
85 °C
125 A
205 A
14
TA 85 °C 55 °C
IP 80 A 125 A
IP,max 218 A 255 A
R
M
25
18
70 °C
100 A
223 A
25
85 °C
125 A
176 A
39
VACUUMSCHMELZE
SPECIFICATION
Item no.:
T60404-N4646-X200
K-No.:
25150 125 A Current Sensor
Date:
20.10.2010
Customer:
Standard type
Customers Part no.:
Page 2 of 2
Hrsg.: KB-E
editor Bearb:
designer
Le. KB-PM: KRe
check freig.: prs.
released
Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden
Any offenders are liable to pay all relevant damages.
For the electronic measurement of currents:
DC, AC, pulsed, mixed ..., with a galvanic isolation
between the primary circuit (high power)
and the secondary circuit (electronic circuit)
Mechanical outline (mm): General tolerances DIN ISO 2768-c
Toleranz der Stiftabstände ±0,2mm
(Tolerances grid distance)
DC = Date Code
F = Factory
*= vorläufig
(preliminary)
48,4
2x12,711,5 5,08
21,4 19,4
6,95
32,0
0,4
5,0±0,5*
27,55
11
18,5
20,5
4,5
14
0,88x0,60
40,64 2xØ1,75
8,89
1234
F DC
Schematic diagram
+ VC
- VC
Ip +
+
-RMCA
+
M
3
2
1
IS
4 NC Leerstift (not connected)
Temperature of the primary conductor should not exceed 110°C
Additional indications are obtainable on request.
This specification is no declaration of warranty acc. BGB §443 dar.
Connections:
1...4: 0,6 x 0,88 mm
4646X200
F DC
Marking:
VACUUMSCHMELZE
Additional Information
Item No.:
T60404-N4646-X200
K-No.:
25150 125 A Current Sensor
Date:
20.10.2010
Customer:
Customers Part No.: Page 1 of 3
Hrsg.: KB-E
editor Bearb:
designer
Le KB-PM: KRe
check freig.: prs.
released
Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts
nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten
Copying of this document, disclosing it to third parties or using the contents there for any
purposes without express written authorization by use illegally forbidden.
Any offenders are liable to pay all relevant damages.
For electronic current measurement:
DC, AC, pulsed, mixed ..., with a galvanic
isolation between primary circuit
(high power) and secondary circuit
Electrical Data (investigate by a type checking)
min. typ. max. Unit
V
Ctot Maximum supply voltage (without function) ±18 V
±15.75 to ±18 V: for 1s per hour
R
S
Secondary coil resistance @ TA=85°C 41
XTi Temperature drift of X @ TA = -40 ... +85 °C 0.1 %
I
0ges Offset current (including I0, I0t, I0T) 0.14 mA
I
0t Long term drift Offset current I0 0.05 mA
I
0T Offset current temperature drift I0 @ TA = -40 ...+85°C 0.05 mA
I
0H Hyteresis current @ IP=0 (caused by primary current 10 x IPN) 0.05 0.1 mA
I0/VC Supply voltage rejection ratio 0.01 mA/V
i
oss Offset ripple (with1 MHz- filter first order) 0.1 mA
i
oss Offset ripple (with 100 kHz- filter first order) 0.015 0.04 mA
i
oss Offset ripple (with 20 kHz- filter first order) 0.007 0.01 mA
C
k
Maximum possible coupling capacity (primary secondary) 7 pF
Inspection (Measurement after temperature balance of the samples at room temperature)
KN(N1/N2) (V) M3011/6 Transformation ratio (IP=100A, 40-80 Hz) 1: 9951005
IP (V) M3011/4 Primary current 100 A
I0 (V) M3226 Offset current < 0.1 mA
Vd (V) M3014: Test voltage, rms, 1 s 1.8 kV
pin 1 3 vs. hole
V
e
(AQL 1/S4) Partial discharge voltage acc.M3024 (RMS) 1300 V
with Vvor (RMS) 1625 V
Type Testing (Pin 1 - 3 to hole)
VW HV transient test according to M3064 (1,2 µs / 50 µs-wave form) 8 kV
V
d
Testing voltage to M3014 (5 s) 3.6 kV
V
e
Partial discharge voltage acc.M3024 (RMS) 1300 V
with Vvor (RMS) 1625 V
Datum Name Index Änderung
20.10.10 Le 81 Date updated.
VACUUMSCHMELZE
Additional Information
Item No.:
T60404-N4646-X200
K-No.:
25150 125 A Current Sensor
Date:
20.10.2010
Customer:
Customers Part No.: Page 2 of 3
Hrsg.: KB-E
editor Bearb:
designer
Le KB-PM: KRe
check freig.: prs.
released
Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts
nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten
Copying of this document, disclosing it to third parties or using the contents there for any
purposes without express written authorization by use illegally forbidden.
Any offenders are liable to pay all relevant damages.
For electronic current measurement:
DC, AC, pulsed, mixed ..., with a galvanic
isolation between primary circuit
(high power) and secondary circuit
Limit curve of measurable current ÎP(RM)
@ ambient temperature 85 °C
0
50
100
150
200
250
300
020406080100120140160180200220240
R
M
[Ω]
N
P
* Î
P
[A]
V
C
= +/-15V - 5%
V
C
= +/-12V - 5%
Maximum measuring range (µs-range)
Output current behaviour of a 3kA current pulse
@ VC = ±15V und RM= 10
0
500
1000
1500
2000
2500
3000
3500
012345678910
t [µs]
I [A]
Ip [A]
Ia / KN [A]
Fast increasing currents (higher than the specified Ip,max), e.g. in case
of a short circuit, can be transmitted because the currents are
transformed directly and be limited by diodes only.
The offset ripple can be reduced by an external low pass. Simplest solution is a passive low pass filter of 1st order with
In this case the response time is enlarged.
It is calculated from:
aMrr CRtt 5,2+
Applicable documents
Current direction: A positive output current appears at point IS, by primary current in direction of the arrow.
Housing and bobbin material UL-listed: Flammability class 94V-0.
aM
gCR
f
=π21
VACUUMSCHMELZE
Additional Information
Item No.:
T60404-N4646-X200
K-No.:
25150 125 A Current Sensor
Date:
20.10.2010
Customer:
Customers Part No.: Page 3 of 3
Hrsg.: KB-E
editor Bearb:
designer
Le KB-PM: KRe
check freig.: prs.
released
Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts
nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu
Schadenersatz. Alle Rechte für den Fall der Patenterteilung oder GM-Eintragung vorbehalten
Copying of this document, disclosing it to third parties or using the contents there for any
purposes without express written authorization by use illegally forbidden.
Any offenders are liable to pay all relevant damages.
For electronic current measurement:
DC, AC, pulsed, mixed ..., with a galvanic
isolation between primary circuit
(high power) and secondary circuit
Explanation of several of the terms used in the tablets (in alphabetical order)
I0H: Zero variation after overloading with a DC of tenfold the rated value (RM = RMN)
I0t: Long term drift of Io after 100 temperature cycles in the range -40 bis 85 °C.
tr: Response time, measured as delay time at IP = 0,8 . IPmax between a rectangular current and the output current.
t (IPmax): Delay time between IPmax and the output current ia with a primary current rise of di1/dt = 100 A/µs.
UPD Rated discharge voltage (recurring peak voltage separated by the insulation) proved with a sinusoidal voltage Ve
UPD = 2 * Ve / 1,5
V
vor Defined voltage is the RMS valve of a sinusoidal voltage with peak value of 1,875 * UPD required for partial discharge
test in IEC 61800-5-1
V
vor = 1,875 *UPD / 2
V
sys System voltage RMS value of rated voltage according to IEC 61800-5-1
Vwork Working voltage voltage according to IEC 61800-5-1 which occurs by design in a circuit or across insulation
Xges(IPN): The sum of all possible errors over the temperature range by measuring a current IPN:
(
)
1
IK
II
100X
PNN
PNS
ges
=
X: Permissible measurement error in the final inspection at RT, defined by
1
I
I
100X SN
SB =
where ISB is the output DC value of an input DC current of the same magnitude as the (positive) rated current (Io = 0 )
X
Ti: Temperature drift of the rated value orientated output term. ISN (cf. Notes on Fi) in a specified temperature range,
obtained by:
(
)
(
)
SN
A1SBA2SB
Ti I
TITI
100
=X
εL: Linearity fault defined by
SN
Sx
PN
P
LI
I
II
100 =ε
Where IP is any input DC and ISx the corresponding output term. ISN: see notes of Fi (Io = 0).
This Additional information is no declaration of warranty according BGB $443.