50 Hz to 6 GHz,
50 dB TruPwr™ Detector
Data Sheet AD8363
Rev. B Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2015 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
Accurate rms-to-dc conversion from 50 Hz to 6 GHz
Single-ended input dynamic range of >50 dB
No balun or external input tuning required
Waveform and modulation independent RF power detection
Linear-in-decibels output, scaled: 52 mV/dB
Log conformance error: <±0.15 dB
Temperature stability: <±0.5 dB
Voltage supply range: 4.5 V to 5.5 V
Operating temperature range: −40°C to +125°C
Power-down capability to 1.5 mW
Small footprint, 4 mm × 4 mm, LFCSP
APPLICATIONS
Power amplifier linearization/control loops
Multi-Standard, Multi-Carrier Wireless Infrastructure
(MCGSM, CDMA, WCDMA, TD-SCDMA, WiMAX, LTE)
Transmitter power control
Transmitter signal strength indication (TSSI)
RF instrumentation
FUNCTIONAL BLOCK DIAGRAM
TCM2/PWDN
X
2
07368-001
1
CHPF
2
VPOS
3
COMM
VREFVTGT VPOS COMM
4
11 10 9
5
CLPF
6
VOUT
7
VSET
8
16
15
14
13
TEMP
TCM1
INLO
INHI
NC
AD8363
12
X
2
Figure 1. AD8363 Block Diagram
GENERAL DESCRIPTION
The AD8363 is a true rms responding power detector that can
be directly driven with a single-ended 50 Ω source. This feature
makes the AD8363 frequency versatile by eliminating the need
for a balun or any other form of external input tuning for operation
up to 6 GHz.
The AD8363 provides an accurate power measurement,
independent of waveform, for a variety of high frequency
communication and instrumentation systems. Requiring only
a single supply of 5 V and a few capacitors, it is easy to use and
provides high measurement accuracy. The AD8363 can operate
from arbitrarily low frequencies to 6 GHz and can accept inputs
that have rms values from less than −50 dBm to at least 0 dBm,
with large crest factors exceeding the requirements for accurate
measurement of WiMAX, CDMA, W-CDMA, TD-SCDMA,
multicarrier GSM, and LTE signals.
The AD8363 can determine the true power of a high frequency
signal having a complex low frequency modulation envelope, or
it can be used as a simple low frequency rms voltmeter. The high-
pass corner generated by its internal offset-nulling loop can be
lowered by a capacitor added on the CHPF pin.
Used as a power measurement device, VOUT is connected to
VSET. The output is then proportional to the logarithm of the
rms value of the input. The reading is presented directly in
decibels and is conveniently scaled to 52 mV/dB, or approximately
1 V per decade; however, other slopes are easily arranged. In
controller mode, the voltage applied to VSET determines the
power level required at the input to null the deviation from the
setpoint. The output buffer can provide high load currents.
The AD8363 has 1.5 mW power consumption when powered
down by a logic high applied to the TCM2/PWDN pin. It powers
up within about 30 μs to its nominal operating current of 60 mA at
25°C. The AD8363 is available in a 4 mm × 4 mm 16-lead LFCSP
for operation over the −40°C to +125°C temperature range.
A fully populated RoHS compliant evaluation board is also
available.
AD8363 Data Sheet
Rev. B | Page 2 of 29
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Absolute Maximum Ratings ............................................................ 7
ESD Caution .................................................................................. 7
Pin Configuration and Function Descriptions ............................. 8
Typical Performance Characteristics ............................................. 9
Theory of Operation ...................................................................... 14
Square Law Detector and Amplitude Target .............................. 14
RF Input Interface ...................................................................... 15
Choice of RF Input Pin .............................................................. 15
Small Signal Loop Response ..................................................... 15
Temperature Sensor Interface ................................................... 16
VREF Interface ........................................................................... 16
Temperature Compensation Interface ..................................... 16
Power-Down Interface ............................................................... 17
VSET Interface ............................................................................ 17
Output Interface ......................................................................... 17
VTGT Interface .......................................................................... 18
Measurement Mode Basic Connections.................................. 18
System Calibration and Error Calculation .............................. 19
Operation to 125°C .................................................................... 19
Output Voltage Scaling .............................................................. 20
Offset Compensation, Minimum CLPF, and Maximum CHPF
Capacitance Values ..................................................................... 20
Choosing a Value for CLPF .......................................................... 21
RF Pulse Response and VTGT ................................................. 23
Controller Mode Basic Connections ....................................... 23
Constant Output Power Operation .......................................... 24
Description of RF Characterization ......................................... 25
Evaluation and Characterization Circuit Board Layouts ...... 26
Assembly Drawings .................................................................... 28
Outline Dimensions ....................................................................... 29
Ordering Guide .......................................................................... 29
REVISION HISTORY
3/15—Rev. A to Rev. B
Changes to Figure 2 and Table 3 ..................................................... 8
Changes to Controller Mode Basic Connections Section ......... 23
Updated Outline Dimensions ....................................................... 29
Changes to the Ordering Guide .................................................... 29
7/11—Rev. 0 to Rev. A
Changes to Features Section and Applications Section ............... 1
Added 3-Point Calibration to Table 1 for All MHz ...................... 3
Replaced Typical Performance Characteristics Section;
Renumbered Sequentially ................................................................ 9
Changes to Theory of Operation Section .................................... 14
Changes to Temperature Compensation Interface Section ...... 16
Changes to System Calibration and Error Calculation
Section and Changes to Figure 44 and Figure 45 ....................... 19
Deleted Basis for Error Calculations Section .............................. 20
Changes to Figure 46 ...................................................................... 20
Deleted Selecting and Increasing Calibration Points to
Improve Accuracy over a Reduced Range Section ..................... 22
Deleted Altering the Slope Section .............................................. 23
Added Output Voltage Scaling Section ....................................... 23
5/09—Revision 0: Initial Version
Data Sheet AD8363
SPECIFICATIONS
VPOS = 5 V, TA = 25°C, ZO = 50 Ω, single-ended input drive, VOUT connected to VSET, VTGT = 1.4 V, CLPF = 3.9 nF, CHPF = 2.7 nF, error
referred to best-fit line (linear regression) from −20 dBm to −40 dBm, unless otherwise noted.
Table 1.
Parameter Conditions Min Typ Max Unit
OVERALL FUNCTION
Maximum Input Frequency 6 GHz
RF INPUT INTERFACE INHI (Pin 14), INLO (Pin 15), ac-coupled
Input Resistance Single-ended drive 50 Ω
Common-Mode DC Voltage 2.6 V
100 MHz TCM1 (Pin 16) = 0.47 V, TCM2 (Pin 1) = 1.0 V, INHI input
Output Voltage: High Power In PIN = −10 dBm 2.47 V
Output Voltage: Low Power In PIN = −40 dBm 0.92 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm, and −40 dBm 64 dB
Best-fit (linear regression) at −20 dBm and −40 dBm 65 dB
Maximum Input Level, ±1.0 dB 9 dBm
Minimum Input Level, ±1.0 dB −56 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −10 dBm −0.2/+0.3 dB
−40°C < TA < +85°C; PIN = −40 dBm −0.5/+0.6 dB
Logarithmic Slope 51.7 mV/dB
Logarithmic Intercept −58 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 40 dB dynamic range <±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range <±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic
range
<±0.1 dB
256 QAM, CF = 8 dB, over 40 dB dynamic range <±0.1 dB
Input Impedance Single-ended drive 49 − j0.09 Ω
900 MHz TCM1 (Pin 16) = 0.5 V, TCM2 (Pin 1) = 1.2 V, INHI input
Output Voltage: High Power In
P
IN
= −15 dBm
2.2
V
Output Voltage: Low Power In PIN = −40 dBm 0.91 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm, and −40 dBm 60 dB
Best-fit (linear regression) at −20 dBm and −40 dBm 54 dB
Maximum Input Level, ±1.0 dB −2 dBm
Minimum Input Level, ±1.0 dB −56 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −15 dBm +0.6/−0.4 dB
−40°C < TA < +85°C; PIN = −40 dBm +0.8/−0.6 dB
Logarithmic Slope 51.8 mV/dB
Logarithmic Intercept −58 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 40 dB dynamic range <±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 40 dB dynamic range <±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 40 dB dynamic
range
<±0.1 dB
256 QAM, CF = 8 dB, over 40 dB dynamic range <±0.1 dB
Input Impedance Single-ended drive 60 − j3.3 Ω
Rev. B | Page 3 of 29
AD8363 Data Sheet
Parameter Conditions Min Typ Max Unit
1.9 GHz TCM1 (Pin 16) = 0.52 V, TCM2 (Pin 1) = 0.51 V, INHI input
Output Voltage: High Power In PIN = −15 dBm 2.10 V
Output Voltage: Low Power In PIN = −40 dBm 0.8 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm, and −40 dBm
56
dB
Best-fit (linear regression) at −20 dBm and −40 dBm 48 dB
Maximum Input Level, ±1.0 dB −6 dBm
Minimum Input Level, ±1.0 dB −53 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −15 dBm +0.3/−0.5 dB
−40°C < TA < +85°C; PIN = −40 dBm +0.4/−0.4 dB
Logarithmic Slope 52 mV/dB
Logarithmic Intercept −55 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 37 dB dynamic range ±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 37 dB dynamic range ±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 37 dB dynamic
range
±0.1 dB
256 QAM, CF = 8 dB, over 37 dB dynamic range ±0.1 dB
Input Impedance Single-ended drive 118 − j26 Ω
2.14 GHz TCM1 (Pin 16) = 0.52 V, TCM2 (Pin 1) = 0.6 V, INHI input
Output Voltage: High Power In PIN = −15 dBm 2.0 V
Output Voltage: Low Power In PIN = −40 dBm 0.71 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm and −40 dBm 55 dB
Best-fit (linear regression) at −20 dBm and −40 dBm
44
dB
Maximum Input Level, ±1.0 dB −8 dBm
Minimum Input Level, ±1.0 dB −52 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −15 dBm +0.1/−0.2 dB
−40°C < TA < +85°C; PIN = −40 dBm +0.3/−0.5 dB
Logarithmic Slope 52.2 mV/dB
Logarithmic Intercept −54 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 35 dB dynamic range ±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 35 dB dynamic range ±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 35 dB dynamic
range
±0.1 dB
256 QAM, CF = 8 dB, over 35 dB dynamic range ±0.1 dB
Rise Time Transition from no input to 1 dB settling at RFIN = −10 dBm,
CLPF = 390 pF, CHPF = open
3 µs
Fall Time Transition from −10 dBm to within 1 dB of final value (that is,
no input level), CLPF = 390 pF, CHPF = open
15 µs
Input Impedance Single-ended drive 130 − j49 Ω
2.6 GHz TCM1 (Pin 16) = 0.54 V, TCM2 (Pin 1) = 1.1 V, INHI input
Output Voltage: High Power In
P
IN
= −15 dBm
1.84
V
Output Voltage: Low Power In PIN = −40 dBm 0.50 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm and −40 dBm 50 dB
Best-fit (linear regression) at −20 dBm and −40 dBm 41 dB
Maximum Input Level, ±1.0 dB −7 dBm
Minimum Input Level, ±1.0 dB −48 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −15 dBm +0.5/−0.2 dB
−40°C < TA < +85°C; PIN = −40 dBm +0.6/−0.2 dB
Rev. B | Page 4 of 29
Data Sheet AD8363
Parameter Conditions Min Typ Max Unit
Logarithmic Slope 52.9 mV/dB
Logarithmic Intercept −49 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 32 dB dynamic range ±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 32 dB dynamic range ±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 32 dB dynamic
range
±0.1
dB
256 QAM, CF = 8 dB, over 32 dB dynamic range ±0.1 dB
Input Impedance Single-ended drive 95 − j65 Ω
3.8 GHz TCM1 (Pin 16) = 0.56 V, TCM2 (Pin 1) = 1.0 V, INLO input
Output Voltage: High Power In PIN = −20 dBm 1.54 V
Output Voltage: Low Power In PIN = −40 dBm 0.54 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm and −40 dBm 50 dB
Best-fit (linear regression) at −20 dBm and −40 dBm 43 dB
Maximum Input Level, ±1.0 dB −5 dBm
Minimum Input Level, ±1.0 dB −48 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −20 dBm +0.1/−0.7 dB
−40°C < TA < +85°C; PIN = −40 dBm +0.4/−0.5 dB
Logarithmic Slope 50.0 mV/dB
Logarithmic Intercept −51 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 32 dB dynamic range ±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 32 dB dynamic range ±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 32 dB dynamic
range
±0.1 dB
256 QAM, CF = 8 dB, over 32 dB dynamic range ±0.1 dB
Input Impedance Single-ended drive 42 − j4.5 Ω
5.8 GHz TCM1 (Pin 16) = 0.88 V, TCM2 (Pin 1) = 1.0 V, INLO input
Output Voltage: High Power In PIN = −20 dBm 1.38 V
Output Voltage: Low Power In PIN = −40 dBm 0.36 V
±1.0 dB Dynamic Range CW input, TA = 25°C
3-point calibration at 0 dBm, −10 dBm and −40 dBm 50 dB
Best-fit (linear regression) at −20 dBm and −40 dBm
45
dB
Maximum Input Level, ±1.0 dB −3 dBm
Minimum Input Level, ±1.0 dB −48 dBm
Deviation vs. Temperature Deviation from output at 25°C
−40°C < TA < +85°C; PIN = −20 dBm +0.1/−0.6 dB
−40°C < TA < +85°C; PIN = −40 dBm +0.3/−0.8 dB
Logarithmic Slope 51.1 mV/dB
Logarithmic Intercept −47 dBm
Deviation from CW Response 13 dB peak-to-rms ratio (W-CDMA), over 32 dB dynamic range ±0.1 dB
12 dB peak-to-rms ratio (WiMAX), over 32 dB dynamic range ±0.1 dB
14.0 dB peak-to-rms ratio (16C CDMA2K), over 32 dB dynamic
range
±0.1 dB
256 QAM, CF = 8 dB, over 32 dB dynamic range ±0.1 dB
Input Impedance Single-ended drive 28 + j1.6 Ω
OUTPUT INTERFACE
VOUT (Pin 6)
Output Swing, Controller Mode Swing range minimum, RL ≥ 500 Ω to ground 0.03 V
Swing range maximum, RL ≥ 500 Ω to ground 4.8 V
Current Source/Sink Capability Output held at VPOS/2 10/10 mA
Voltage Regulation ILOAD = 8 mA, source/sink −0.2/+0.1 %
Rise Time Transition from no input to 1 dB settling at RFIN = −10 dBm,
CLPF = 390 pF, CHPF = open
3 µs
Rev. B | Page 5 of 29
AD8363 Data Sheet
Parameter Conditions Min Typ Max Unit
Fall Time Transition from −10 dBm to within 1 dB of final value (that is,
no input level), CLPF = 390 pF, CHPF = open
15 µs
Noise Spectral Density Measured at 100 kHz 45 nV/√Hz
SETPOINT INPUT VSET (Pin 7)
Voltage Range Log conformance error ≤ 1 dB, minimum 2.14 GHz 2.0 V
Log conformance error ≤ 1 dB, maximum 2.14 GHz 0.7 V
Input Resistance 72 kΩ
Logarithmic Scale Factor
f = 2.14 GHz, −40°C ≤ T
A
≤ +85°C
19.2
dB/V
Logarithmic Intercept f = 2.14 GHz, −40°C ≤ TA ≤ +85°C, referred to 50 Ω −54 dBm
TEMPERATURE COMPENSATION TCM1 (Pin 16), TCM2 (Pin 1)
Input Voltage Range 0 2.5 V
Input Bias Current, TCM1 VTCM1 = 0 V −140 µA
VTCM1 = 0.5 V 80 µA
Input Resistance, TCM1 VTCM1 > 0.7 V 5 kΩ
Input Current, TCM2 VTCM2 = 5 V 2 µA
VTCM2 = 4.5 V 750 µA
VTCM2 = 1 V −2 µA
VTCM2 = 0 V −3 µA
Input Resistance, TCM2 0.7 V ≤ VTCM2 ≤ 4.0 V 500 kΩ
VOLTAGE REFERENCE VREF (Pin 11)
Output Voltage RFIN = −55 dBm 2.3 V
Temperature Sensitivity
25°C ≤ T
A
≤ 70°C
0.04
mV/°C
70°C ≤ TA ≤ 125°C −0.06 mV/°C
−40°C ≤ TA ≤ +25°C −0.18 mV/°C
Current Source/Sink Capability 25°C ≤ TA ≤ 125°C 4/0.05 mA
−40°C ≤ TA < +25°C 3/0.05 mA
Voltage Regulation TA = 25°C, ILOAD = 3 mA −0.6 %
TEMPERATURE REFERENCE TEMP (Pin 8)
Output Voltage TA = 25°C, RL ≥ 10 kΩ 1.4 V
Temperature Coefficient −40°C ≤ TA ≤ +125°C, RL ≥ 10 kΩ 5 mV/°C
Current Source/Sink Capability
25°C ≤ T
A
≤ 125°C
4/0.05
mA
−40°C ≤ TA < +25°C 3/0.05 mA
Voltage Regulation TA = 25°C, ILOAD = 3 mA −0.1 %
RMS TARGET INTERFACE VTGT (Pin 12)
Input Voltage Range 1.4 2.5 V
Input Bias Current VTGT = 1.4 V 14 µA
Input Resistance 100 kΩ
POWER-DOWN INTERFACE TCM2 (Pin1)
Logic Level to Enable VPWDN decreasing 4.2 V
Logic Level to Disable VPWDN increasing 4.7 V
Input Current VTCM2 = 5 V 2 µA
V
TCM2
= 4.5 V
750
µA
VTCM2 = 1 V −2 µA
VTCM2 = 0 V −3 µA
Enable Time TCM2 low to VOUT at 1 dB of final value, CLPF = 470 pF,
CHPF = 220 pF, RFIN = 0 dBm
35 µs
Disable Time TCM2 high to VOUT at 1 dB of final value, CLPF = 470 pF,
CHPF = 220 pF, RFIN = 0 dBm
25 µs
POWER SUPPLY INTERFACE VPOS (Pin 3, Pin 10)
Supply Voltage 4.5 5 5.5 V
Quiescent Current TA = 25°C, RFIN = −55 dBm 60 mA
TA = 85°C 72 mA
Power-Down Current VTCM2 > VPOS − 0.3 V 300 µA
Rev. B | Page 6 of 29
Data Sheet AD8363
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Supply Voltage, VPOS 5.5 V
Input Average RF Power
1
21 dBm
Equivalent Voltage, Sine Wave Input 2.51 V rms
Internal Power Dissipation 450 mW
θJC2 10.6°C/W
θJB2 35.3°C/W
θJA2 57.2°C/W
ΨJT2 1.0°C/W
ΨJB2 34°C/W
Maximum Junction Temperature 150°C
Operating Temperature Range −40°C to +125°C
Storage Temperature Range −65°C to +150°C
Lead Temperature (Soldering, 60 sec) 300°C
1 This is for long durations. Excursions above this level, with durations much
less than 1 second, are possible without damage.
2 No airflow with the exposed pad soldered to a 4-layer JEDEC board.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
Rev. B | Page 7 of 29
AD8363 Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
TCM2/PWDN
CHPF
VPOS
COMM
VREF
VTGT
VPOS
COMM
CLPF
VOUT
VSET
TEMP
INLO
TCM1
INHI
NC
07368-002
NOTES
1. NC = NO CO NNE C T. DO NOT CONNECT TO THIS PIN.
2. THE EXPOSED PAD IS THE SYSTEM COMMON
CONNECTI ON AND IT M US T HAVE BOT H A GOOD
THERMALAND GOOD ELECT RICAL CONNECTI ON
TO GROUND.
12
11
10
1
3
49
2
6
5
7
8
16
15
14
13
AD8363
TOP VIEW
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin
No. Mnemonic Description
Equivalent
Circuit
1
TCM2/PWDN
This is a dual function pin used for controlling the amount of nonlinear intercept temperature
compensation at voltages <2.5 V and/or for shutting down the device at voltages >4 V. If the
shutdown function is not used, this pin can be connected to the VREF pin through a voltage
divider.
See Figure 39
2 CHPF Connect this pin to VPOS via a capacitor to determine the −3 dB point of the input signal high-
pass filter. Only add a capacitor when operating at frequencies below 10 MHz.
See Figure 48
3, 10 VPOS Supply for the Device. Connect these pins to a 5 V power supply. Pin 3 and Pin 10 are not internally
connected; therefore, both must connect to the source.
Not
applicable
4, 9 COMM System Common Connection. Connect these pins via low impedance to system common. Not
applicable
5 CLPF Connection for Loop Filter Integration (Averaging) Capacitor. Connect a ground-referenced
capacitor to this pin. A resistor can be connected in series with this capacitor to improve loop
stability and response time. Minimum CLPF value is 390 pF.
See Figure 41
6 VOUT Output Pin in Measurement Mode (Error Amplifier Output). In measurement mode, this pin is
connected to VSET. This pin can be used to drive a gain control when the device is used in
controller mode.
See Figure 41
7 VSET The voltage applied to this pin sets the decibel value of the required RF input voltage that results
in zero current flow in the loop integrating capacitor pin, CLPF. This pin controls the variable gain
amplifier (VGA) gain such that a 50 mV change in VSET reduces the gain by approximately 1 dB.
See Figure 40
8 TEMP Temperature Sensor Output. See Figure 35
11 VREF General-Purpose Reference Voltage Output of 2.3 V. See Figure 36
12 VTGT The voltage applied to this pin determines the target power at the input of the RF squaring circuit. The
intercept voltage is proportional to the voltage applied to this pin. The use of a lower target
voltage increases the crest factor capacity; however, this may affect the system loop response.
See Figure 42
13 NC No Connect. Not
applicable
14 INHI This is the RF input pin for frequencies up to and including 2.6 GHz. The RF input signal is normally
ac-coupled to this pin through a coupling capacitor.
See Figure 34
15
INLO
This is the RF input pin for frequencies above 2.6 GHz. The RF input signal is normally ac-coupled
to this pin through a coupling capacitor.
See Figure 34
16 TCM1 This pin is used to adjust the intercept temperature compensation. Connect this pin to VREF
through a voltage divider or to an external dc source.
See Figure 38
EPAD Exposed Pad. The exposed pad is the system common connection and it must have both a good
thermal and good electrical connection to ground.
Not
applicable
Rev. B | Page 8 of 29
Data Sheet AD8363
TYPICAL PERFORMANCE CHARACTERISTICS
VPOS = 5 V, ZO = 50 Ω, single-ended input drive, VOUT connected to VSET, VTGT = 1.4 V, C LPF = 3.9 nF, CHPF = 2.7 nF, TA = +25°C (black),
−40°C (blue), +85°C (red), where appropriate. Error calculated using 3-point calibration at 0 dBm, −10 dBm, and −40 dBm, unless
otherwise indicated. Input RF signal is a sine wave (CW), unless otherwise indicated.
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-103
Figure 3. VOUT and Log Conformance vs. Input Power and
Temperature at 100 MHz
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-104
Figure 4. VOUT and Log Conformance Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 900 MHz, CW, Typical Device
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-105
Figure 5. VOUT and Log Conformance Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 1.90 GHz, CW, Typical Device
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-106
Figure 6. Distribution of VOUT and Error with Respect to 25°C Ideal Line over
Temperature vs. Input Amplitude at 100 MHz, CW
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
P
IN
(d Bm)
V
OUT
(V)
ERROR ( dB)
07368-107
Figure 7. Distribution of VOUT and Error with Respect to 25°C Ideal Line over
Temperature vs. Input Amplitude at 900 MHz, CW
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-108
Figure 8. Distribution of VOUT and Error with Respect to 25°C Ideal Line over
Temperature vs. Input Amplitude at 1.90 GHz, CW
Rev. B | Page 9 of 29
AD8363 Data Sheet
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-109
Figure 9. VOUT and Log Conformance Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 2.14 GHz, CW, Typical Device
3.00
2.50
2.00
1.50
1.00
0.50
0
2.75
2.25
1.75
1.25
0.75
0.25
4
5
6
3
2
1
0
–1
–2
–3
–4
–5
–6
–60 –50 –40 –30 –20 –10 010
P
IN
(d Bm)
V
OUT
(V)
ERROR ( dB)
07368-110
Figure 10. VOUT and Log Conformance Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 2.6 GHz, CW, Typical Device
3.00
2.50
2.75
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
4
5
6
3
2
1
0
–1
–2
–3
–4
–5
–6
–60 –50 –40 –30 –20 –10 010
P
IN
(d Bm)
OUTPUT VOLTAGE (V)
ERROR ( dB)
07368-111
Figure 11. VOUT and Log Conformance Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 3.8 GHz, CW, Typical Device
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 010
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-112
Figure 12. Distribution of VOUT and Error with Respect to 25°C Ideal Line over
Temperature vs. Input Amplitude at 2.14 GHz, CW
3.00
2.50
2.00
1.50
1.00
0.50
0
2.75
2.25
1.75
1.25
0.75
0.25
4
5
6
3
2
1
0
–1
–2
–3
–4
–5
–6
–60 –50 –40 –30 –20 –10 010
P
IN
(d Bm)
V
OUT
(V)
ERROR ( dB)
07368-113
Figure 13. Distribution of VOUT and Error with Respect to 25°C Ideal Line over
Temperature vs. Input Amplitude at 2.6 GHz, CW
3.00
2.50
2.75
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
4
5
6
3
2
1
0
–1
–2
–3
–4
–5
–6
–60 –50 –40 –30 –20 –10 010
P
IN
(d Bm)
OUTPUT VOLTAGE (V)
ERROR ( dB)
07368-114
Figure 14. Distribution of VOUT and Error with Respect to 25°C Ideal Line over
Temperature vs. Input Amplitude at 3.8 GHz, CW
Rev. B | Page 10 of 29
Data Sheet AD8363
Rev. B | Page 11 of 29
3.00
2.50
2.75
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
4
5
6
3
2
1
0
–1
–2
–3
–4
–5
–6
–60 –50 –40 –30 –20 –10 0 10
P
IN
(dBm)
OUTPUT VOLTAGE (V)
ERROR ( dB)
07368-115
Figure 15. VOUT and Log Conformance Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 5.8 GHz, Typical Device
3
2
1
0
–1
–2
–3
–60 –50 –40 –30 –20 –10 0 10
P
IN
(dBm)
ERROR (dB)
07368-026
ERROR CW
ERROR W-CDM A 1 CAR TM1 64 DPCH
ERROR W-CDM A 2 CAR TM1 64 DPCH
ERROR W-CDM A 3 CAR TM1 64 DPCH
ERROR W-CDM A 4 CAR TM1 64 DPCH
Figure 16. Error from CW Linear Reference vs. Input Amplitude with
Modulation, Frequency at 2.14 GHz, CLPF = 0.1 μF, INHI Input
100MHz 900MHz
5.8GHz
3.8GHz
1.9GHz
2.6GHz
2.14GHz
07368-030
Figure 17. Single-Ended Input Impedance (S11) vs.
Frequency; ZO = 50 Ω, INHI or INLO
3.00
2.50
2.75
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
4
5
6
3
2
1
0
–1
–2
–3
–4
–5
–6
–60 –50 –40 –30 –20 –10 0 10
P
IN
(dBm)
OUTPUT VOLTAGE (V)
ERROR ( dB)
07368-118
Figure 18. Distribution of VOUT and Error with Respect to 25°C Ideal Line
over Temperature vs. Input Amplitude at 5.8 GHz, CW
2
3
1
0
–1
–2
–3
–60 –50 –40 –30 –20 –10 0 10
P
IN
(dBm)
ERROR (dB)
07368-028
CW
W-CDM A 1 CAR T M1 32 DP CH
QPSK
256QAM
WIMAX 256 SUBCR, 6 4 QAM, 1 0MHz BW
CDMA2K 9 CH S R1 4 CAR
Figure 19. Error from CW Linear Reference vs. Input Amplitude with
Modulation, Frequency at 2.6 GHz, CLPF = 0.1 μF, INHI Input
160
140
120
100
80
60
40
20
0
100 1k 10k 100k 1M 10M
FREQ UE NCY (Hz )
NOISE SPECTRAL DENSITY (n V/ Hz)
07368-031
Figure 20. Typical Noise Spectral Density of VOUT; All CLPF Values
AD8363 Data Sheet
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–0.5
–1.0 12 13 14 15 167 8 9 10 112 3 4 5 6
–2 –1 0 1 TIME (µs)
V
OUT
(V)
07368-033
0dBm –10dBm –20dBm –30dBm –40d Bm
RF
ENVELOPE
Figure 21. Output Response to RF Burst Input, Carrier Frequency at 2.14 GHz,
CLPF = 390 pF, CHPF = Open, Rising Edge
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–0.5
–1.0 2 3 4 5–1 0 1 TIME (ms)
V
OUT
(V)
07368-034
0dBm –10dBm –20dBm
–30dBm –40dBm
RF
ENVELOPE
Figure 22. Output Response to RF Burst Input, Carrier Frequency at 2.14 GHz,
CLPF = 0.1 µF, CHPF = Open, Rising Edge
6
5
4
3
2
1
0
6
3
0
–50
–25
0
25
50
75
100
125
150
175
200
225
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
TIME (µs)
OUTPUT VOLTAGE, V
OUT
(V)
V
TCM2
(V)
07368-037
0dBm
–50dBm
TCM2 LOW TCM 2 HIGH
Figure 23. Output Response Using Power-Down Mode for Various RF Input
Levels Carrier Frequency at 2.14 GHz, CLPF = 470 pF, CHPF = 220 pF
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–2 2 4 6 8 10 12 14 16 18 20 22 24 26 28 300TIME (µs)
V
OUT
(V)
07368-035
RF
ENVELOPE
0dBm –10dBm –20dBm –30dBm –40d Bm
Figure 24. Output Response to RF Burst Input, Carrier Frequency at 2.14 GHz,
CLPF = 390 pF, CHPF = Open, Falling Edge
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–0.5
–1.0 2 3 4–1 01TI ME (ms)
V
OUT
(V)
07368-036
0dBm –10dBm –20dBm
–30dBm –40dBm
RF
ENVELOPE
Figure 25. Output Response to RF Burst Input, Carrier Frequency at 2.14 GHz,
CLPF = 0.1 µF, CHPF = Open, Falling Edge
1.75
2.00
1.50
1.25
0
1.00
0.75
0.50
0.25
3
4
2
1
0
–1
–2
–3
–4
–50–40–30–20–10 010 20 30 40 50 60 70 80 90 100110 120130
TEMPERATURE (°C)
V
TEMP
(V)
ERROR ( °C)
07368-027
Figure 26. VTEMP and Error with Respect to Straight Line vs. Temperature for
Eleven Devices
Rev. B | Page 12 of 29
Data Sheet AD8363
Rev. B | Page 13 of 29
600
400
200
800
0
1.34 1.36 1.38 1.40 1.42 1.44 1.46
V
TEMP
(V)
QUANTITY
07368-077
REPRESENTS
APPROXIMATELY
3000 PARTS FROM
SIX LOT S
Figure 27. Distribution of VTEMP Voltage at 25oC, No RF Input
100
10
1
0.1
4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0
VTCM2 (V )
SUPPLY CURRE NT (mA)
07368-051
VTCM2 INCREASING
VTCM2 DE CRE AS ING
Figure 28. Supply Current vs. VTCM2
2.34
2.33
2.32
2.31
2.30
2.29
2.28
2.27
2.26
–30 –25 –20 –15 –10 –5 0 5 10
P
IN
(dBm)
V
REF
(V)
07368-049
Figure 29. Change in VREF with Input Amplitude for Eleven Devices
600
500
400
300
200
100
0
2.24 2.26 2.28 2.30 2.32 2.34 2.36
VREF (V)
QUANTITY
07368-029
REPRESENTS
APPROXIMATELY
3000 PARTS FR OM
SIX LOT S
Figure 30. Distribution of VREF, 25°C, No RF Input
2.320
2.318
2.316
2.314
2.312
2.310
2.308
2.306
2.304
2.302
2.300
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
V
POS
(V)
V
REF
(V)
07368-038
Figure 31. Change in VREF with VPOS for Nine Devices
2.325
2.320
2.315
2.310
2.305
2.300
2.290
2.295
–40 –20 0 20 40 60 80 100 120
TEMPERATURE ( °C)
VREF (V)
07368-048
Figure 32. Change in VREF with Temperature for Eleven Devices
AD8363 Data Sheet
Rev. B | Page 14 of 29
THEORY OF OPERATION
The computational core of the AD8363 is a high performance
AGC loop. As shown in Figure 33, the AGC loop comprises a
wide bandwidth variable gain amplifier (VGA), square law
detectors, an amplitude target circuit, and an output driver. For
a more detailed description of the functional blocks, see the
AD8362 data sheet.
The nomenclature used in this data sheet to distinguish
between a pin name and the signal on that pin is as follows:
The pin name is all uppercase (for example, VPOS,
COMM, and VOUT).
The signal name or a value associated with that pin is the
pin mnemonic with a partial subscript (for example, CLPF,
CHPF, and VOUT).
SQUARE LAW DETECTOR AND AMPLITUDE TARGET
The VGA gain has the form
GSET = GO exp(−VSET/VGNS) (1)
where:
GO is the basic fixed gain.
VGNS is a scaling voltage that defines the gain slope (the decibel
change per voltage). The gain decreases with increasing VSET.
The VGA output is
VSIG = GSET × RFIN = GO × RFIN exp(VSET/VGNS) (2)
where RFIN is the ac voltage applied to the input terminals of the
AD8363.
The output of the VGA, VSIG, is applied to a wideband square
law detector. The detector provides the true rms response of the
RF input signal, independent of waveform. The detector output,
ISQR, is a fluctuating current with positive mean value. The
difference between ISQR and an internally generated current,
ITGT, is integrated by CF and the external capacitor attached to
the CLPF pin at the summing node. CF is an on-chip 25 pF filter
capacitor, and CLPF, the external capacitance connected to the
CLPF pin, can be used to arbitrarily increase the averaging time
while trading off with the response time. When the AGC loop is
at equilibrium
Mean(ISQR) = ITGT (3)
This equilibrium occurs only when
Mean(VSIG2) = VTGT2 (4)
where VTGT is the voltage presented at the VTGT pin. This pin
can conveniently be connected to the VREF pin through a voltage
divider to establish a target rms voltage VATG of ~70 mV rms, when
VTGT = 1.4 V.
Because the square law detectors are electrically identical and
well matched, process and temperature dependent variations
are effectively cancelled.
TCM1
TCM2/PWDN
BAND GA P
REFERENCE
COMM
VOUT
TEMP (1.4V)
VREF (2.3V)
I
SQR
I
TGT
X
2
X
2
G
SET
C
H
(INTERNAL) C
HPF
(EXTERNAL)
C
LPF
(EXTERNAL) C
F
(INTERNAL)
V
SIG
VGA
SUMMING
NODE
VSET
CHPF
VPOS
INHI
INLO
TE MP E RAT URE CO M P ENS ATI O N
AND BIA S
TEMPERATURE
SENSOR
VTGT
CLPF
V
ATG
= V
TGT
20
07368-076
Figure 33. Simplified Architecture Details
Data Sheet AD8363
Rev. B | Page 15 of 29
By forcing the previous identity through varying the VGA setpoint,
it is apparent that
RMS(VSIG) = √(Mean(VSIG2)) = √(VATG2) = VATG (5)
Substituting the value of VSIG from Equation 2 results in
RMS(G0 × RFIN exp(−VSET/VGNS)) = VATG (6)
When connected as a measurement device, VSET = VOUT. Solving
for VOUT as a function of RFIN
VOUT = VSLOPE × log10(RMS(RFIN)/VZ) (7)
where:
VSLOPE is 1 V/decade (or 50 mV/dB).
VZ is the intercept voltage.
When RMS(RFIN) = VZ, because log10(1) = 0, this implies that
VOUT = 0 V, making the intercept the input that forces VOUT = 0 V.
VZ has been fixed to approximately 280 μV (approximately
−58 dBm, referred to 50 Ω) with a CW signal at 100 MHz.
In reality, the AD8363 does not respond to signals less than
~−56 dBm. This means that the intercept is an extrapolated
value outside the operating range of the device.
If desired, the effective value of VSLOPE can be altered by using
a resistor divider between VOUT and VSET. (Refer to the
Output Voltage Scaling section for more information.)
In most applications, the AGC loop is closed through the
setpoint interface and the VSET pin. In measurement mode,
VOUT is directly connected to VSET. (See the Measurement
Mode Basic Connections section for more information.) In
controller mode, a control voltage is applied to VSET and the
VOUT pin typically drives the control input of an amplification
or attenuation system. In this case, the voltage at the VSET pin
forces a signal amplitude at the RF inputs of the AD8363 that
balances the system through feedback. (See the Controller
Mode Basic Connections section for more information.)
RF INPUT INTERFACE
Figure 34 shows the connections of the RF inputs within
the AD8363. The input impedance is set primarily by an internal
50 Ω resistor connected between INHI and INLO. A dc level of
approximately half the supply voltage on each pin is established
internally. Either the INHI pin or the INLO pin can be used as
the single-ended RF input pin. (See the Choice of RF Input Pin
section.) If the dc levels at these pins are disturbed, performance
is compromised; therefore, signal coupling capacitors must be
connected from the input signal to INHI and INLO. The input
signal high-pass corner formed by the coupling capacitors and
the internal resistances is
fHIGH-PASS = 1/(2 × π × 50 × C) (8)
where C is in farads and fHIGH-PASS is in hertz. The input coupling
capacitors must be large enough in value to pass the input signal
frequency of interest. The other input pin should be RF ac-coupled
to common (ground).
07368-039
ESD ESD ESD ESD ESD ESD
ESD ESD ESD ESD ESD ESD
ESD
ESD ESD
ESD ESD
2.5kΩ2.5kΩ
50Ω
V
BIAS
VPOS
INHI INLO
Figure 34. RF Inputs Simplified Schematic
Extensive ESD protection is employed on the RF inputs, which
limits the maximum possible input amplitude to the AD8363.
CHOICE OF RF INPUT PIN
The dynamic range of the AD8363 can be optimized by choosing
the correct RF input pin for the intended frequency of operation.
Using INHI (Pin 14), users can obtain the best dynamic range at
frequencies up to 2.6 GHz. Above 2.6 GHz, it is recommended
that INLO (Pin 15) be used. At 2.6 GHz, the performance obtained
at the two inputs is approximately equal.
The AD8363 was designed with a single-ended RF drive in
mind. A balun can be used to drive INHI and INLO differentially,
but it is not necessary, and it does not result in improved
dynamic range.
SMALL SIGNAL LOOP RESPONSE
The AD8363 uses a VGA in a loop to force a squared RF signal
to be equal to a squared dc voltage. This nonlinear loop can be
simplified and solved for a small signal loop response. The low-
pass corner pole is given by
FreqLP ≈ 1.83 × ITGT/(CLPF) (9)
where:
ITGT is in amperes.
CLPF is in farads.
FreqLP is in hertz.
ITGT is derived from VTGT; however, ITGT is a squared value of
VTGT multiplied by a transresistance, namely
ITGT = gm × VTGT2 (10)
gm is approximately 18.9 μs, so with VTGT equal to the typically
recommended 1.4 V, ITGT is approximately 37 μA. The value of
this current varies with temperature; therefore, the small signal
pole varies with temperature. However, because the RF squaring
circuit and dc squaring circuit track with temperature, there is no
temperature variation contribution to the absolute value of VOUT.
For CW signals,
FreqLP ≈ 67.7 × 10−6/(CLPF) (11)
However, signals with large crest factors include low
pseudorandom frequency content that either needs to be
filtered out or sampled and averaged out. See the Choosing a
Value for CLPF section for more information.
AD8363 Data Sheet
Rev. B | Page 16 of 29
TEMPERATURE SENSOR INTERFACE
The AD8363 provides a temperature sensor output with an
output voltage scaling factor of approximately 5 mV/°C. The
output is capable of sourcing 4 mA and sinking 50 μA maximum at
temperatures at or above 25°C. If additional current sink capability
is desired, an external resistor can be connected between the
TEMP and COMM pins. The typical output voltage at 25°C is
approximately 1.4 V.
07368-041
TEMP
VPOS
COMM
INTERNAL
VPAT
12kΩ
4kΩ
Figure 35. TEMP Interface Simplified Schematic
VREF INTERFACE
The VREF pin provides an internally generated voltage reference.
The VREF voltage is a temperature stable 2.3 V reference that is
capable of sourcing 4 mA and sinking 50 μA maximum at
temperatures at or above 25°C. An external resistor can be
connected between the VREF and COMM pins to provide
additional current sink capability. The voltage on this pin can be
used to drive the TCM1, TCM2/PWDN, and VTGT pins, if desired.
07368-042
INTERNAL
VOLTAG E
16kΩ
VREF
VPOS
COMM
Figure 36. VREF Interface Simplified Schematic
TEMPERATURE COMPENSATION INTERFACE
Proprietary techniques are used to maximize the temperature
stability of the AD8363. For optimal performance, the output
temperature drift must be compensated for using the TCM1 and
TCM2/PWDN pins. The absolute value of compensation varies
with frequency and VTGT. Table 4 shows the recommended voltages
for the TCM1 and TCM2/PWDN pins to maintain the best
temperature drift error over the rated temperature range (−40°C <
TA < 85°C) when driven single-ended and using a VTGT = 1.4 V.
Table 4. Recommended Voltages for TCM1 and TCM2/PWDN
Frequency TCM1 (V) TCM2/PWDN (V)
100 MHz 0.47 1.0
900 MHz 0.5 1.2
1.9 GHz 0.52 0.51
2.14 GHz 0.52 0.6
2.6 GHz 0.54 1.1
3.8 GHz 0.56 1.0
5.8 GHz 0.88 1.0
The values in Table 4 were chosen to give the best drift
performance at the high end of the usable dynamic range over
the −40°C to +85°C temperature range.
Compensating the device for the temperature drift using TCM1
and TCM2/PWDN allows for great flexibility and the user may
wish to modify these values to optimize for another amplitude
point in the dynamic range, for a different temperature range,
or for an operating frequency other than those shown in Table 4.
To find a new compensation point, VTCM1 and VTCM2 can be
swept while monitoring VOUT over the temperature at the
frequency and amplitude of interest. The optimal voltages for
VTCM1 and VTCM2 to achieve minimum temperature drift at a given
power and frequency are the values of VTCM1 and VTCM2 where
VOUT has minimum movement. See the AD8364 and ADL5513
data sheets for more information.
Varying VTCM1 and VTCM2 has only a very slight effect on VOUT at
device temperatures near 25°C; however, the compensation circuit
has more and more effect, and is more and more necessary for
best temperature drift performance, as the temperature departs
farther from 25°C.
Figure 37 shows the effect on temperature drift performance at
25°C and 85°C as VTCM1 is varied but VTCM2 is held constant at 0.6 V.
3
2
1
0
–1
–2
–3
–60 –50 –40 –30 –20 –10 0 10
RF
IN
(dBm)
ERROR (dB)
07368-050
25°C
85°C
V
TCM1
= 0.62V
V
TCM1
= 0.42V
Figure 37. Error vs. Input Amplitude over Stepped VTCM1 Values,
25oC and 85oC, 2.14 GHz, VTCM2 = 0.6 V
TCM1 primarily adjusts the intercept of the AD8363 at
temperature. In this way, TCM1 can be thought of as a coarse
adjustment to the compensation. Conversely, TCM2 performs a
fine adjustment. For this reason, it is advised that when searching
for compensation with VTCM1 and VTCM2, that VTCM1 be adjusted
first, and when best performance is found, VTCM2 can then be
adjusted for optimization.
It is evident from Figure 37 that the temperature compensation
circuit can be used to adjust for the lowest drift at any input
amplitude of choice. Though not shown in Figure 37, a similar
analysis can simultaneously be performed at −40°C, or any
other temperature within the operating range of the AD8363.
Performance varies slightly from device to device; therefore,
optimal VTCM1 and VTCM2 values must be arrived at statistically
Data Sheet AD8363
Rev. B | Page 17 of 29
over a population of devices to be useful in mass production
applications.
The TCM1 and TCM2 pins have high input impedances,
approximately 5 kΩ and 500 kΩ, respectively, and can be
conveniently driven from an external source or from a fraction
of VREF by using a resistor divider. VREF does change slightly
with temperature and RF input amplitude (see Figure 32 and
Figure 29); however, the amount of change is unlikely to result
in a significant effect on the final temperature stability of the RF
measurement system.
Figure 38 shows a simplified schematic representation of TCM1.
See the Power-Down Interface section for the TCM2 interface.
07368-043
3kΩ
3kΩ
ESD
ESD
ESD
V
POS
COMM
TCM1
Figure 38. TCM1 Interface Simplified Schematic
POWER-DOWN INTERFACE
The quiescent and disabled currents for the AD8363 at 25°C are
approximately 60 mA and 300 μA, respectively. The dual function
pin, TCM2/PWDN, is connected to a temperature compensation
circuit as well as a power-down circuit. Typically, when PWDN
is greater than VPOS − 0.1 V, the device is fully powered down.
Figure 28 shows this characteristic as a function of VPWDN. Note
that because of the design of this section of the AD8363, as
VTCM2 passes through a narrow range at ~4.5 V (or ~VPOS − 0.5 V),
the TCM2/PWDN pin sinks approximately 750 μA. The source
used to disable the AD8363 must have a sufficiently high current
capability for this reason. Figure 23 shows the typical response
times for various RF input levels. The output reaches within 0.1 dB
of its steady-state value in approximately 35 μs; however, the refer-
ence voltage is available to full accuracy in a much shorter time.
This wake-up response varies depending on the input coupling
and the capacitances, CHPF and CLPF.
07368-044
TCM2/
PWDN
COMM
V
POS
200Ω
200Ω
7kΩ7kΩ
VREF
INTERCEPT
TEMPERATURE
COMPENSATION
200Ω
POWER-UP
CIRCUIT
SHUTDOWN
CIRCUIT
ESD
ESD
ESD
Figure 39. PWDN Interface Simplified Schematic
VSET INTERFACE
The VSET interface has a high input impedance of 72 kΩ.
The voltage at VSET is converted to an internal current used
to set the internal VGA gain. The VGA attenuation control is
approximately 19 dB/V.
07368-045
COMM
2.5kΩ
18kΩ
VSET
GAIN ADJUST
54kΩ
Figure 40. VSET Interface Simplified Schematic
OUTPUT INTERFACE
The output driver used in the AD8363 is different from the
output stage on the AD8362. The AD8363 incorporates rail-to-
rail output drivers with pull-up and pull-down capabilities. The
closed-loop −3 dB bandwidth of the VOUT buffer with no load
is approximately 58 MHz with a single-pole roll-off of −20 dB/dec.
The output noise is approximately 45 nV/√Hz at 100 kHz, which is
independent of CLPF due to the architecture of the AD8363.
VOUT can source and sink up to 10 mA. There is an internal
load between VOUT and COMM of 2.5 kΩ.
07368-046
VOUT
CLPF
2kΩ
500Ω
2pF
ESD
ESD
ESD
V
POS
COMM
Figure 41. VOUT Interface Simplified Schematic
AD8363 Data Sheet
Rev. B | Page 18 of 29
VTGT INTERFACE
The target voltage can be set with an external source or by
connecting the VREF pin (nominally 2.3 V) to the VTGT pin
through a resistive voltage divider. With 1.4 V on the VTGT pin,
the rms voltage that must be provided by the VGA to balance the
AGC feedback loop is 1.4 V × 0.05 = 70 mV rms. Most of the
characterization information in this data sheet was collected at
VTGT = 1.4 V. Voltages higher and lower than this can be used;
however, doing so increases or decreases the gain at the internal
squaring cell, which results in a corresponding increase or
decrease in intercept. This in turn affects the sensitivity and the
usable measurement range. Because the gain of the squaring
cell varies with temperature, oscillations or a loss in measurement
range can result. For these reasons, do not reduce VTGT below 1.3 V.
07368-047
VTGT 50kΩ
50kΩ
10kΩ
ESD
ESD
ESD
VPOS
COMM
g × X
2
ITGT
Figure 42. VTGT Interface Simplified Schematic
MEASUREMENT MODE BASIC CONNECTIONS
The AD8363 requires a single supply of nominally 5 V. The
supply is connected to the two supply pins, VPOS. Decouple
the pins using two capacitors with values equal or similar to
those shown in Figure 43. These capacitors must provide a low
impedance over the full frequency range of the input, and they
should be placed as close as possible to the VPOS pins. Use two
different capacitor values in parallel to provide a broadband ac
short to ground.
Input signals can be applied differentially or single-ended; however,
in both cases, the input impedance is 50 Ω. Most performance
information in this data sheet was derived with a single-ended
drive. The optimal measurement range is achieved using a single-
ended drive on the INHI pin at frequencies below 2.6 GHz (as
shown in Figure 43), and likewise, optimal performance is
achieved using the INLO pin above 2.6 GHz (similar to Figure 43;
except INLO is ac-coupled to the input and INHI is ac-coupled
to ground).
The AD8363 is placed in measurement mode by connecting
VOUT to VSET. This closes the AGC loop within the device
with VOUT representing the VGA control voltage, which is
required to present the correct rms voltage at the input of the
internal square law detector.
TEMP
8
7
6
5
VOUT
TCM1
13
14
15
16
VREF
VPOS2
12 11 10 9
1234
TCM2/PWDN
VPOS1
NC
INHI
INLO
TCM1
TEMP
VSET
VOUT
CLPF
VTGT
VREF
VPOS
COMM
TCM2/PWDN
CHPF
VPOS
COMM
AD8363
DUT1
0
7368-062
C12
0.1µF
C10
0.1µF
C7
0.1µF
C5
100pF
LOW FREQUENCY INPUT
C9
0.1µF
C4
100pF
C13
0.1µF
C3
OPEN
PADDLE
AGND
R11
1.4kΩ
R10
845Ω
Figure 43. Measurement Mode Basic Connections
Data Sheet AD8363
Rev. B | Page 19 of 29
SYSTEM CALIBRATION AND ERROR CALCULATION
The measured transfer function of the AD8363 at 1.9 GHz is
shown in Figure 44, which contains plots of both output voltage
vs. input amplitude (power) and calculated error vs. input level. As
the input level varies from −55 dBm to +0 dBm, the output
voltage varies from ~0 V to ~3.1 V.
Because slope and intercept vary from device to device, board-
level calibration must be performed to achieve high accuracy.
The equation for the idealized output voltage can be written as
VOUT(IDEAL) = Slope × (PIN − Intercept) (12)
where:
Slope is the change in output voltage divided by the change in
input power (dB).
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 0 10
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-144
Figure 44. 1.9 GHz Transfer Function and Linearity Error using a Two-Point
Calibration (Calibration Points −20 dBm and −40 dBm)
Intercept is the calculated input power level at which the output
voltage would equal 0 V (note that Intercept is an extrapolated
theoretical value not a measured value).
In general, calibration, which establishes the Slope and Intercept,
is performed during equipment manufacture by applying two
or more known signal levels to the input of the AD8363 and
measuring the corresponding output voltages. The calibration
points are generally chosen within the linear-in-dB operating
range of the device.
With a two-point calibration, the slope and intercept are
calculated as follows:
Slope = (VOUT1 − VOUT2)/(PIN1 − PIN2) (13)
Intercept = PIN1 − (VOUT1/Slope) (14)
After the slope and intercept are calculated and stored in non-
volatile memory during equipment calibration, an equation can
be used to calculate an unknown input power based on the
output voltage of the detector.
PIN (Unknown) = (VOUT1(MEASURED)/Slope) + Intercept (15)
The log conformance error is the difference between this
straight line and the actual performance of the detector.
Error (dB) = (VOUT(MEASURED) − VOUT(IDEAL))/Slope (16)
Figure 44 includes a plot of this error when using a two-point
calibration (calibration points are −20 dBm and −40 dBm). e
error at the calibration points is equal to 0 by definition.
The residual nonlinearity of the transfer function that is
apparent in the two-point calibration error plot can be reduced
by increasing the number of calibration points. Figure 45 shows
the post-calibration error plots for three-point calibration. With
a multipoint calibration, the transfer function is segmented,
with each segment having its own slope and intercept. During
calibration, multiple known power levels are applied, and
multiple voltages are measured. When the equipment is in
operation, the measured voltage from the detector is first used
to determine which of the stored slope and intercept calibration
coefficients are to be used. Then the unknown power level is
calculated by inserting the appropriate slope and intercept into
Equation 15.
Figure 45 shows the output voltage and error at 25°C and over
temperature when a three-point calibration is used (calibration
points are 0 dBm, −10 dBm and −40 dBm). When choosing
calibration points, there is no requirement for, or value in equal
spacing between the points. There is also no limit to the
number of calibration points used.
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
4
3
2
1
0
–1
–2
–3
–4
–60 –50 –40 –30 –20 –10 0 10
PIN (dBm)
VOUT (V)
ERROR ( dB)
07368-145
Figure 45. 1.9 GHz Transfer Function and Error at +25°C, −40°C, and +85°C
Using a Three-Point Calibration (0 dBm, −10 dBm and −40 dBm)
The −40°C and +85°C error plots in Figure 44 and Figure 45
are generated using the 25°C calibration coefficients. This is
consistent with equipment calibration in a mass production
environment where calibration at just a single temperature is
practical.
OPERATION TO 125°C
The AD8363 operates up to 125°C with slightly degraded
performance. Figure 46 shows the typical operation (Errors are
plotted using two-point calibration) at 125°C as compared to
other temperatures using the TCM1 and TCM2 values in Table 4.
Temperature compensation can be optimized for operation
above 85°C by modifying the voltages on the TCM1 and TCM2
pins from those shown in Table 4.
AD8363 Data Sheet
Rev. B | Page 20 of 29
4
5
6
3
2
1
0
3
2
1
0
–3
–1
–2
–60 –50 –40 –30 –20 –10 0 10
P
IN
(dBm)
OUTPUT VOLT AGE (V)
ERROR ( dB)
07368-053
INHI INPUT
V
TCM1
= 0.52V, V
TCM2
= 0.6V
–40°C
+25°C
+85°C
+125°C
Figure 46. VOUT and Log Conformance Error vs. Input Amplitude at 2.14 GHz,
−40°C to +125°C
OUTPUT VOLTAGE SCALING
The output voltage range of the AD8363 (nominally 0 V to
3.5 V) can be easily increased or decreased. There are a number
of situations where adjustment of the output scaling makes
sense. For example, if the AD8363 is driving an analog-to-
digital converter (ADC) with a 0 V to 5 V input range, it makes
sense to increase the detector’s nominal maximum output
voltage of 3.5 V so that it is closer to 5 V. This makes better use
of the input range of the ADC and maximizes the resolution of
the system in terms of bits/dB.
If only a part of the RF input power range of the AD8363 is
being used (for example, −10 dBm to −40 dBm), it may make
sense to increase the scaling so that this reduced input range fits
into the available output swing of the AD8363 (0 V to 4.8 V).
The output swing can be reduced by adding a voltage divider on
the output pin, as shown in Figure 47 (with VOUT connected
directly to VSET and a resistor divider on VOUT). Figure 47
also shows how the output voltage swing can be increased using
a technique that is analogous to setting the gain of an op amp in
noninverting mode. With the VSET pin being the equivalent of
the inverting input of the op amp, a resistor divider is connected
between VOUT and VSET.
6
7VSET
R1
R2
VOUT
6
7VSET
R1
R2
VOUT
07368-146
Figure 47. Decreasing and Increasing Slope
Equation 17 is the general function that governs this.
1)||( '
O
O
IN V
V
RR2R1
(17)
where:
VO is the nominal maximum output voltage (see Figure 4
through Figure 18).
V'O is the new maximum output voltage (for example, up to
4.8 V).
RIN is the VSET input resistance (72 kΩ).
When choosing R1 and R2, attention must be paid to the
current drive capability of the VOUT pin and the input
resistance of the VSET pin. The choice of resistors should not
result in excessive current draw out of VOUT. However, making
R1 and R2 too large is also problematic. If the value of R2 is
compatible with the 72 kΩ input resistance of the VSET input,
this input resistance, which varies slightly from device to device,
contributes to the resulting slope and output voltage. In general,
the value of R2 should be at least ten times smaller than the
input resistance of VSET. Values for R1 and R2 should, therefore,
be in the 1 k to 5 k range.
It is also important to take into account device-to-device and
frequency variation in output swing along with the AD8363
output stage’s maximum output voltage of 4.8 V. The VOUT
distribution is well characterized at the bands of major
frequencies in the Typical Performance Characteristics section
(Figure 3 to Figure 18).
OFFSET COMPENSATION, MINIMUM CLPF, AND
MAXIMUM CHPF CAPACITANCE VALUES
An offset-compensation loop is used to eliminate small dc
offsets within the internal VGA as shown in Figure 48. The
high-pass corner frequency of this loop is set to about 1 MHz
using an on-chip 25 pF capacitor. Because input signals that are
below 1 MHz are interpreted as unwanted offset voltages, this
restricts the operating frequency range of the device. To operate the
AD8363 at lower frequencies (than 1 MHz), the high-pass corner
frequency must be reduced by connecting a capacitor between
CHPF and VPOS.
Internal offset voltages vary depending on the gain at which the
VGA is operating and, therefore, on the input signal amplitude.
When a large CHPF value is used, the offset correction process can
lag the more rapid changes in the gain of the VGA, which can
increase the time required for the loop to fully settle for a given
steady input amplitude. This can manifest itself in a jumpy,
seemingly oscillatory response of the AD8363.
Care should therefore be taken in choosing CHPF and CLPF
because there is a potential to create oscillations. In general, make
the capacitance on the CLPF pin as large as possible; there is no
maximum on the amount of capacitance that can be added to
this pin. At high frequencies, there is no need for an external
capacitor on the CHPF pin; therefore, the pin can be left open.
However, when trying to get a fast response time and/or when
working at low frequencies, extra care in choosing the proper
capacitance values for CHPF and CLPF is prudent. With the gain
control pin (VSET) connected to VOUT, VSET can slew at a rate
determined by the on-chip squaring cell and CLPF. When VSET is
changing with time, the dc offsets in the VGA also vary with
Data Sheet AD8363
time. The speed at which VSET slews can create a time varying offset
that falls within the high-pass corner set by CHPF. Therefore, in
measurement mode, take care to set CLPF appropriately to reduce
the slew. It is also worth noting that most of the typical
performance data was derived with CLPF = 3.9 nF and CHPF = 2.7 nF
and with a CW waveform.
The minimum appropriate CLPF based on slew rate limitations is
as follows
CLPF > 20 × 10−3/FREQRFIN (18)
where:
CLPF is in farads.
FREQRFIN is in hertz.
This takes into account the on-chip 25 pF capacitor, CF, in
parallel with CLPF. However, because there are other internal
device time delays that affect loop stability, use a minimum CLPF
of 390 pF.
The minimum appropriate CHPF for a given high-pass pole
frequency is
CHPF = 29.2 × 10−6/FHPPOLE − 25 pF (19)
where FHPPOLE is in hertz.
The subtraction of 25 pF is a result of the on-chip 25 pF
capacitor in parallel with the external CHPF. Typically, choose
CHPF to give a pole (3 dB corner) at least 1 decade below the
desired signal frequency. Note that the high pass corner of the
offset compensation system is approximately 1 MHz without an
external CHPF; therefore, adding an external capacitor lowers the
corner frequency.
The following example illustrates the proper selection of the input
coupling capacitors, minimum CLPF, and maximum CHPF when
using the AD8363 in measurement mode for a 1 GHz input signal.
1. Choose the input coupling capacitors that have a 3 dB
corner at least one decade below the input signal frequency.
From Equation 8, C > 10/(2 × π × RFIN × 50) = 32 pF
minimum. According to this calculation, 32 pF is sufficient;
however, the input coupling capacitors should be a much
larger value, typically 0.1 µF. The offset compensation
circuit, which is connected to CHPF, should be the true
determinant of the system high-pass corner frequency and
not the input coupling capacitors. With 0.1 µF coupling
capacitors, signals as low as 32 kHz can couple to the input,
which is well below the system high-pass frequency.
2. Choose CLPF to reduce instabilities due to VSET slew rate.
See Equation 18, where FRQRFIN = 1 GHz, and this results in
CLPF > 20 pF. However, as previously mentioned, values
below 390 pF are not recommended. For this reason, a 470 pF
capacitor was chosen. In addition, if fast response times are
not required, an even larger CLPF value than given here
should be chosen.
3. Choose CHPF to set a 3 dB corner to the offset compensation
system. See Equation 19, where FHPPOLE is in this case
100 MHz, one decade below the desired signal. This results
in a negative number and, obviously, a negative value is not
practical. Because the high-pass corner frequency is already
1 MHz, this result simply illustrates that the appropriate
solution is to use no external CHPF capacitor.
Note that per Equation 9
FreqLP ≈ 1.83 × ITGT/(CLPF)
A CLPF of 470 pF results in a small signal low-pass corner
frequency of approximately 144 kHz. This reflects the bandwidth
of the measurement system, and how fast the user can expect
changes on the output. It does not imply any limitations on the
input RF carrier frequency.
gm2
07368-040
gm1
A = 1
40dB g × X
2
gm
CHPF
V
X
VPOS
VGA
110Ω 110Ω
25pF
(INTERNAL) 1pF 1pF
IRF
RFIN
Figure 48. Offset Compensation Circuit
CHOOSING A VALUE FOR CLPF
The Small Signal Loop Response section and the Offset
Compensation, Minimum CLPF, and Maximum CHPF
Capacitance Values section discussed how to choose the
minimum value capacitance for CLPF based on a minimum
capacitance of 390 pF, slew rate limitation, and frequency of
operation. Using the minimum value for CLPF allows the quickest
response time for pulsed type waveforms (such as WiMAX) but
also allows the most residual ripple on the output caused by the
pseudorandom modulation waveform. There is not a maximum
for the capacitance that can be applied to the CLPF pin, and in
most situations, a large enough capacitor can be added to remove
the residual ripple caused by the modulation and yet allow a fast
enough response to changes in input power.
Figure 49 shows how residual ripple, rise time, and fall time
vary with filter capacitance when the AD8363 is driven by a
single carrier CDMA2000 9CH SR1 signal at 2.14 GHz. The rise
time and fall time is based on a signal that is pulsed between no
signal and 10 dBm but is faster if the input power change is less.
Rev. B | Page 21 of 29
AD8363 Data Sheet
400
350
300
250
200
150
100
50
0
2800
2450
2100
1750
1400
1050
700
0
350
010 20 30 40 50 60 70 80 90 100
C
LPF
CAPACITANCE ( nF )
RESIDUAL RIPPLE (mV p-p)
RISE TIME (µs)
FALL TIME (µs)
07368-069
RESIDUAL RIPPLE (mV)
RISE TIME (µs)
FALL TI ME (µs)
Figure 49. Residual Ripple, Rise Time, and Fall Time vs. CLPF Capacitance,
Single Carrier CDMA2000 9CH SR1 Signal at 2.14 GHz with 10 dBm Pulse
Table 5 shows the recommended values of CLPF for popular
modulation schemes. For nonpulsed waveforms, increase CLPF until
the residual output noise falls below 50 mV (±0.5 dB). In each case,
the capacitor can be increased to further reduce the noise. A 10% to
90% step response to an input step is also listed. Where the
increased response time is unacceptably high, reduce CLPF, which
increases the noise on the output. Due to the random nature of the
output ripple, if it is sampled by an ADC, averaging in the digital
domain further reduces the residual noise.
Table 5 gives CLPF values to minimize noise while trying to keep
a reasonable response time. For non-pulsed type waveforms,
averaging is not required on the output. For pulsed waveforms,
the smaller the noise, the less averaging is needed on the output.
System specifications determine the necessary rise time and fall
time. For example, the suggested CLPF value for WiMAX assumes
that it is not necessary to measure the power in the preamble.
Figure 50 shows how the rise time cuts off the preamble. Note
that the power in the preamble can be easily measured; however,
the CLPF value would have to be reduced slightly, and the noise in
the main signal would increase.
07368-054
CH1 500mV M 1.00ms A CH1 600mV
CH1 RISE
81.78µs
CH1 FALL
1.337ms
1
T 10.00%
T
Figure 50. AD8363 Output Response to a WiMAX 802.16, 64 QAM, 256
Subcarriers, 10 MHz Bandwidth Signal with CLPF = 0.027 µF
As shown in Figure 49, the fall time for the AD8363 increases
faster than the rise time with an increase in CLPF capacitance.
Some pulse-type modulation standards require a fast fall time as
well as a fast rise time, and in all cases, less output ripple is desired.
Placing an RC filter on the output reduces the ripple, according
to the frequency content of the ripple and the poles and zeros of
the filter. Using an RC output filter also changes the rise and fall
time vs. the output ripple response as compared to increasing
the CLPF capacitance.
Table 5. Recommended CLPF Values for Various Modulation Schemes
Modulation/Standard Crest Factor (dB) CLPF
Residual Ripple
(mV p-p)
Response Time (Rise/Fall)
10% to 90%
W-CDMA, 1Carrier, TM1-64 12 0.1 µF 15 236 μs/2.9 ms
W-CDMA, 1Carrier, TM1-64 (EVDO) 12 3900 pF 150 8.5 μs/100 µs
W-CDMA 4Carrier, TM1-64 11 0.1 µF 8 240 μs/2.99 ms
CDMA2000, 1Carrier, 9CH 9.1 0.1 µF 10 210 μs/3.1 ms
CDMA2000, 3Carrier, 9CH 11 0.1 µF 13 215 μs/3.14 ms
WiMAX 802.16 , 64 QAM, 256 Subcarriers, 10 MHz Bandwidth 14 0.027 µF 10 83 µs/1.35 ms
6C TD-SCDMA 14 0.01 µF 69 24 μs/207 μs
1C TD-SCDMA 11.4 0.01 µF 75 24 μs /198 μs
Rev. B | Page 22 of 29
Data Sheet AD8363
Rev. B | Page 23 of 29
Figure 51 shows the response for a 2.14 GHz pulsed signal,
with CLPF = 3900 pF. The residual ripple from a single carrier
CDMA2000 9CH SR1 signal is 150 mV p-p. (The ripple is not
shown in Figure 51. The ripple was measured separately.) Figure 52
shows the response for a 2.14 GHz pulse signal with a CLPF of
390 pF and an output filter that consists of a series 75 Ω resistor
(closest to the output) followed by a 0.15 μF capacitor to ground.
The residual ripple for this configuration is also 150 mV p-p.
Note that the rise time is faster and the fall time is slower when
the larger CLPF is used to obtain a 150 mV p-p ripple.
07368-070
CH1 500mV M 100µs A CH1 720mV
1
T 10.40%
T
CH1 RISE
8.480µs
CH1 FALL
101.4µs
CH1 AMPL
2.37V
Figure 51. Pulse Response with CLPF = 3900 pF Resulting in a 150 mV p-p
Ripple for a Single Carrier CDMA2000 9CH SR1 Signal at 2.14 GHz
07368-071
CH1 500mV M 100µs A CH1 750mV
1
T 10.60%
T
CH1 RISE
13.66µs
CH1 FALL
35.32µs
CH1 AMPL
2.36V
VSET
TEMP
VOUT
CLPF
75Ω
390pF
0.15µF
6
5
8
7
OSCILLOSCOPE
PROBE
Figure 52. Pulse Response with CLPF = 390 pF and Series 75 Ω Resistor
Followed by a 0.15 μF Capacitor to Ground, Resulting in a 150 mV p-p
Ripple for a Single Carrier CDMA2000 9CH SR1 Signal at 2.14 GHz
RF PULSE RESPONSE AND VTGT
The response of the AD8363 to pulsed RF waveforms is affected
by VTGT. Referring to Figure 21 and Figure 22, there is a period
of inactivity between the start of the RF waveform and the time
at which VOUT begins to show a reaction. This happens as a result of
the implementation of the balancing of the squarer currents within
the AD8363. This delay can be reduced by decreasing VTGT;
however, as previously noted in the VTGT Interface section,
this has implications on the sensitivity, intercept, and dynamic
range. While the delay is reduced, reducing VTGT increases the
rise and fall time of VOUT.
CONTROLLER MODE BASIC CONNECTIONS
In addition to being a measurement device, the AD8363 can
also be configured to control rms signal levels, as shown in
Figure 53.
The RF input to the device is configured as it was in measurement
mode and either input can be used. A directional coupler taps
off some of the power being generated by the VGA. If loss in the
main signal path is not a concern, and there are no issues with
reflected energy from the next stage in the signal chain, a power
splitter can be used instead of a directional coupler. Some
additional attenuation may be required to set the maximum
input signal at the AD8363 to be equal to the recommended
maximum input level for optimum linearity and temperature
stability at the frequency of operation.
The VSET and VOUT pins are no longer shorted together. VOUT
now provides a bias or gain control voltage to the VGA. The gain
control sense of the VGA must be negative and monotonic, that is,
increasing voltage tends to decrease gain. However, the gain
control transfer function of the device does not need to be well
controlled or particularly linear. If the gain control sense of the
VGA is positive, an inverting op amp circuit with a dc offset
shift can be used between the AD8363 and the VGA to keep the
gain control voltage in the 0.03 V to 4.8 V range.
VSET becomes the set-point input to the system. This can be
driven by a DAC, as shown in Figure 53, if the output power is
expected to vary, or it can simply be driven by a stable reference
voltage, if constant output power is required. This DAC should
have an output swing that covers the 0.15 V to 3.5 V range.
AD8363
CLPF
C10
C12
VSET
VOUT
DAC
(0.15V TO 3.5V)
(0.03V TO 4.8V AVAILABLE SWING)
ATTENUATOR
P
OUT
P
IN
V
APC
VGA OR VVA
(OUTPUT POWER
DECREASES AS
V
APC
INCREASES)
INHI
INLO
C9
SEE TEXT
07368-063
Figure 53. Controller Mode Operation for Automatic Power Control
When VSET is set to a particular value, the AD8363 compares
this value to the equivalent input power present at the RF input.
If these two values do not match, VOUT increases or decreases in
an effort to balance the system. The dominant pole of the error
amplifier/integrator circuit that drives VOUT is set by the capacitance
on the CLPF pin; some experimentation may be necessary to
choose the right value for this capacitor.
AD8363 Data Sheet
Rev. B | Page 24 of 29
In general, CLPF should be chosen to provide stable loop operation
for the complete output power control range. If the slope (in
dB/V) of the gain control transfer function of the VGA is not
constant, CLPF must be chosen to guarantee a stable loop when
the gain control slope is at its maximum. In addition, CLPF must
provide adequate averaging to the internal low range squaring
detector so that the rms computation is valid. Larger values of CLPF
tend to make the loop less responsive.
The relationship between VSET and the RF input follows the
measurement mode behavior of the device. For example, Figure 4
shows the measurement mode transfer function at 900 MHz
and that an input power of −10 dBm yields an output voltage of
approximately 2.5 V. Therefore, in controller mode, if VSET is
2.5 V, the AD8363 output would go to whatever voltage is
necessary to set the AD8363 input power to −10 dBm.
CONSTANT OUTPUT POWER OPERATION
In controller mode, the AD8363 can be used to hold the output
power of a VGA stable over a broad temperature/input power
range. This is useful in topologies where a transmit card is driving
an HPA, or when connecting any two power sensitive modules
together.
Figure 54 shows a schematic of a circuit setup that holds the output
power to approximately −26 dBm at 2.14 GHz, when the input
power is varied over a 40 dB dynamic range. Figure 55 shows
the results. A portion of the output power is coupled off using a
10 dB directional coupler, and it is then fed into the AD8363.
VSET is fixed at 0.95 V, which forces to AD8363 output voltage to
control the ADL5330 so that the input to the AD8363 is
approximately −36 dBm.
If the AD8363 was in measurement mode and a −36 dBm input
power is applied, the output voltage would be 0.95 V. A general-
purpose, rail-to-rail op amp (AD8062) is used to invert the slope
of the AD8363 so that the gain of the ADL5330 decreases as
the AD8363 control voltage increases. The output power is
controlled to a 10 dB higher power level than that seen by
the AD8363 due to the coupler. The high-end power is limited
by the linearity of the VGA (ADL5330) with high attenuation
and can be increased by using a higher linearity VGA.
The low end power is limited by the maximum gain of the VGA
(ADL5330) and can be increased by using a VGA with more
gain. The temperature performance is directly related to the
temperature performance of the AD8363 at 2.14 GHz and
−26 dBm, using TCM1 = 0.52 V and TCM2 = 0.6 V. All other
temperature variations are removed by the AD8363.
T1 T2
C5
100pF
C6
100pF
C11
100pF
C12
100pF
C10
0.1µF
C12
0.1µF
C9
0.1µF
P
IN
INHI
INLO
OPHI
OPLO
GAIN
ADL5330
P
OUT
10dB
COUPLER
AD8062
10kΩ
10kΩ10kΩ
10kΩ
5V
0.95V
0.6V
0.52V INHITCM1
TCM2
VSET
VOUT
CLPF
INLO
AD8363
07368-072
Figure 54. Constant Power Circuit
–
25.0
–25.5
–26.0
–26.5
–27.0
–27.5
–28.0
–40 –35 –30 –25 –20 –15 –10 –5 0
P
IN
(dBm)
P
OUT
(dBm)
07368-055
–20°C
–40°C
+85°C
+25°C
0°C
Figure 55. Performance of the Circuit Shown in Figure 54
Data Sheet AD8363
Rev. B | Page 25 of 29
DESCRIPTION OF RF CHARACTERIZATION
The general hardware configuration used for most of the AD8363
characterization is shown in Figure 56. The AD8363 was driven
in a single-ended configuration for all characterization.
Characterization of the AD8363 employed a multisite test
strategy. Several AD8363 devices mounted on circuit boards
constructed with Rogers 3006 material was simultaneously
inserted into a remotely-controlled thermal test chamber. A
Keithley S46 RF switching network connected an Agilent E8251A
signal source to the appropriate device under test. An Agilent
34980A switch matrix provided switching of dc power and
metering for the test sites. A PC running Agilent VEE Pro
controlled the signal source, switching, and chamber temperature.
A voltmeter measured the subsequent response to the stimulus,
and the results were stored in a database for later analysis. In this
way, multiple AD8363 devices were characterized over amplitude,
frequency, and temperature in a minimum amount of time.
The RF stimulus amplitude was calibrated up to the connector
of the circuit board that carries the AD8363. However, the
calibration does not account for the slight losses due to the
connector and the traces from the connector to the device
under test. For this reason, there is a small absolute amplitude
error (<0.5 dB) not accounted for in the characterization data.
This implies a slight error in the reported intercept; however,
this is generally not important because the slope and the relative
accuracy of the AD8363 are not affected.
The typical performance data was derived with CLPF = 3.9 nF
and CHPF = 2.7 nF with a CW waveform.
AD8363
CHARACTERIZATION
BOARD – T EST SI TE 1
AD8363
CHARACTERIZATION
BOARD – T EST SI TE 2
KEI THL EY S46
MICROWAVE
SWITCH
AGIL ENT E8251 A
MICROWAVE
SIGNAL
GENERATOR
AGI LENT 34980 A
SW ITCH MATRIX/
DC METER
AGIL ENT E3631 A
DC POWER
SUPPLIES
PERSONAL
COMPUTER
AD8363
CHARACTERIZATION
BOARD – T EST SI TE 3
RF DC DATA AND CO NTROL
07368-075
Figure 56. General RF Characterization Configuration
AD8363 Data Sheet
EVALUATION AND CHARACTERIZATION CIRCUIT
BOARD LAYOUTS
Figure 57 to Figure 61 show the evaluation board for the AD8363.
TEMP
VPOS
C9
0.1µF
C8
OPEN
8
7
6
5
VSET
VOUT
VOUT
C10
0.1µF
C6
OPEN TCM1
VPOSC
13
14
15
16
C5
100pF
VPOS
R10
845Ω
R11
1.4kΩ
C7
0.1µF
12 11 10 9
1 2 3
GND
4
C3
OPEN C4
100pF
C12
0.1µF
C11
OPEN
C13
0.1µF
PADDLE
AGND
NC
INHI
INLO
TCM1
TEMP
VSET
VOUT
CLPF
VTGT
VREF
VPOS
COMM
TCM2/PWDN
CHPF
VPOS
COMM
AD8363
DUT1
07368-074
VPOS1
TCM2/PWDN
VREFC
R16
0Ω
R5
0Ω
R2
OPEN
R14
0Ω
R8
0Ω
R13
OPEN
R1
0Ω
R6
0Ω
R9
OPEN
R18
OPEN
R17
OPEN
R12
OPEN
VREFC
IN
R7
0Ω
R15
0Ω
VREFVTGT
GNDI
Figure 57. Evaluation Board Schematic
Rev. B | Page 26 of 29
Data Sheet AD8363
Table 6. Evaluation Board Configuration Options
Component Function/Notes Default Value
C6, C10,
C11, C12
Input. The AD8363 is single-ended driven. At frequencies ≤2.6 GHz, the best dynamic range is achieved by
driving Pin 14 (INHI). When driving INHI, populate C10 and C12 with an appropriate capacitor value for the
frequency of operation and leave C6 and C11 open. For frequencies >2.6 GHz, additional dynamic range
can be achieved by driving Pin 15 (INLO). When driving INLO, populate C6 and C11 with an appropriate
capacitor value for the frequency of operation and leave C10 and C12 open.
C6 = open,
C10 = 0.1 µF,
C11 = open
C12 = 0.1 µF
R7, R8, R10,
R11
VTGT. R10 and R11 are set up to provide 1.4 V to VTGT from VREF. If R10 and R11 are removed, an external
voltage can be used. Alternatively, R7 and R11 can be used to form a voltage divider for an external
reference.
R7 = 0 Ω,
R8 = 0 Ω,
R10 = 845 Ω,
R11 = 1.4 kΩ
C4, C5, C7,
C13, R14, R16
Power Supply Decoupling. The nominal supply decoupling consists of a 100 pF filter capacitor placed
physically close to the AD8363, a 0 Ω series resistor, and a 0.1 µF capacitor placed close to the power
supply input pin. The 0 Ω resistor can be replaced with a larger resistor to add more filtering; however, it is
at the expense of a voltage drop.
C4 = 100 pF,
C5 = 100 pF,
C7 = 0.1µF,
C13 = 0.1µF,
R14 = 0 Ω,
R16 = 0 Ω
R1, R2, R6,
R13, R15
Output Interface (Default Configuration) in Measurement Mode. In this mode, a portion of the output
voltage is fed back to the VSET pin via R6. Using the voltage divider created by R2 and R6, the magnitude
of the slope at VOUT is increased by reducing the portion of VOUT that is fed back to VSET. If a fast
responding output is expected, the 0 Ω resistor (R15) can be removed to reduce parasitics on the output.
R1 = 0 Ω,
R2 = open,
R6 = 0 Ω,
R13 = open,
R15 = 0 Ω
Output Interface in Controller Mode. In this mode, R6 must be open and R13 must have a 0 Ω resistor. In
controller mode, the AD8363 can control the gain of an external component. A setpoint voltage is applied
to the VSET pin, the value of which corresponds to the desired RF input signal level applied to the AD8363.
If a fast responding output is expected, the 0 Ω resistor (R15) can be removed to reduce parasitics on the output.
C8, C9, R5 Low-Pass Filter Capacitors, CLPF. The low-
pass filter capacitors reduce the noise on the output and affect the
pulse response time of the AD8363. This capacitor should be as large as possible. The smallest CLPF capacitance
should be 390 pF. R5, when set to a value other than 0 Ω, is used in conjunction with C8 and C9 to modify
the loop transfer function and change the loop dynamics in controller mode.
C8 = open,
C9 = 0.1 µF,
R5 = 0 Ω
C3 CHPF Capacitor. The CHPF capacitor introduces a high-pass filter affect into the AD8363 transfer function and
can also affect the response time. The CHPF capacitor should be as small as possible and connect to VPOS
when used. No capacitor is needed for input frequencies greater than 10 MHz.
C3 = open
R9, R12 TCM2/PWDN. The TCM2/PWDN pin controls the amount of nonlinear intercept temperature compensation
and/or shuts down the device. The evaluation board is configured to control this from a test loop, but VREF
can also be used by the voltage divider created by R9 and R12.
R9 = open,
R12 = open
R17, R18 TCM1. TCM1 controls the temperature compensation (5 kΩ impedance). The evaluation board is configured to
control this from a test loop, but VREF can also be used by the voltage divider created by R17 and R18. Due
to the relatively low impedance of the TCM1 pin and the limited current of the VREF pin, care should be
taken when choosing the R17 and R18 values.
R17 = open,
R18 = open
Paddle Connect the paddle to both a thermal and electrical ground.
Rev. B | Page 27 of 29
AD8363 Data Sheet
Rev. B | Page 28 of 29
ASSEMBLY DRAWINGS
07368-058
Figure 58. Evaluation Board Layout, Top Side
0
7368-059
Figure 59. Evaluation Board Layout, Bottom Side
07368-060
Figure 60. Evaluation Board Assembly, Top Side
07368-061
Figure 61. Evaluation Board Assembly, Bottom Side
Data Sheet AD8363
Rev. B | Page 29 of 29
OUTLINE DIMENSIONS
COMPLIANT
TO
JEDEC S TANDARDS MO - 220-WGG C- 3 .
1
0.65
BSC
BOTTOM VI E WTOP VIEW
16
5
8
9
1213
4
EXPOSED
PAD
PIN 1
INDICATOR
4.10
4.00 SQ
3.90
0.50
0.40
0.30
SEATING
PLANE
0.80
0.75
0.70 0.05 MAX
0.02 NOM
0.20 RE F
0.25 MIN
COPLANARITY
0.08
PIN 1
INDICATOR
0.35
0.30
0.25
2.40
2.35 S Q
2.30
FO R P RO P E R CO NNECTI O N OF
THE EXPOSED PAD, REFER TO
THE P IN CO N FI GURAT IO N AN D
FUNCTION DE S CRIPTI ONS
SECTION O F THI S DATA SHE ET.
07-18-2012-B
Figure 62. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-16-20)
Dimensions shown in millimeters
ORDERING GUIDE
Model1 Temperature Range Package Description Package Option Ordering Quantity
AD8363ACPZ-R2 −40°C to +125°C 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-16-20 250
AD8363ACPZ-R7 −40°C to +125°C 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-16-20 1,500
AD8363ACPZ-WP −40°C to +125°C 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-16-20 64
AD8363-EVALZ Evaluation Board
1 Z = RoHS Compliant Part.
©2009–2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07368-0-3/15(B)
