SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 HIGH-SPEED DIFFERENTIAL LINE DRIVERS DESCRIPTION The SN55LVDS31, SN65LVDS31, SN65LVDS3487, and SN65LVDS9638 are differential line drivers that implement the electrical characteristics of low-voltage differential signaling (LVDS). This signaling technique lowers the output voltage levels of 5-V differential standard levels (such as TIA/EIA-422B) to reduce the power, increase the switching speeds, and allow operation with a 3.3-V supply rail. Any of the four current-mode drivers will deliver a minimum differential output voltage magnitude of 247 mV into a 100- load when enabled. The intended application of these devices and signaling technique is both point-to-point and multidrop (one driver and multiple receivers) data transmission over controlled impedance media of approximately 100 . The transmission media may be printed-circuit board traces, backplanes, or cables. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment. 3 14 4 13 5 12 6 11 7 10 8 9 VCC 4A 4Y 4Z G 3Z 3Y 3A 3 2 1 20 19 4A NC SN55LVDS31FK (TOP VIEW) 1Z 4 18 4Y G 5 17 4Z NC 6 16 NC 2Z 7 15 G 2Y 8 14 3Z 9 10 11 12 13 3Y * 15 VCC * * * 16 2 3A * 1 NC * * * 1A 1Y 1Z G 2Z 2Y 2A GND 1Y * SN55LVDS31 . . . J OR W SN65LVDS31 . . . D OR PW (Marked as LVDS31 or 65LVDS31) (TOP VIEW) 1A * Meet or Exceed the Requirements of ANSI TIA/EIA-644 Standard Low-Voltage Differential Signaling With Typical Output Voltage of 350 mV and 100- Load Typical Output Voltage Rise and Fall Times of 500 ps (400 Mbps) Typical Propagation Delay Times of 1.7 ns Operate From a Single 3.3-V Supply Power Dissipation 25 mW Typical Per Driver at 200 MHz Driver at High Impedance When Disabled or With VCC = 0 Bus-Terminal ESD Protection Exceeds 8 kV Low-Voltage TTL (LVTTL) Logic Input Levels Pin Compatible With AM26LS31, MC3487, and A9638 Cold Sparing for Space and High Reliability Applications Requiring Redundancy 2A * GND FEATURES SN65LVDS3487D (Marked as LVDS3487 or 65LVDS3487) (TOP VIEW) 1A 1Y 1Z 1,2EN 2Z 2Y 2A GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC 4A 4Y 4Z 3,4EN 3Z 3Y 3A SN65LVDS9638D (Marked as DK638 or LVDS38) SN65LVDS9638DGN (Marked as L38) SN65LVDS9638DGK (Marked as AXG) (TOP VIEW) VCC 1A 2A GND 1 8 2 7 3 6 4 5 1Y 1Z 2Y 2Z Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1997-2007, Texas Instruments Incorporated SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION (CONTINUED) The SN65LVDS31, SN65LVDS3487, and SN65LVDS9638 are characterized for operation from -40C to 85C. The SN55LVDS31 is characterized for operation from -55C to 125C. AVAILABLE OPTIONS PACKAGE (1) TA SMALL OUTLINE -40C to 85C (PW) MSOP CHIP CARRIER (FK) CERAMIC DIP (J) FLAT PACK (W) SN65LVDS31D SN65LVDS31PW -- -- -- -- SN65LVDS3487D -- -- -- -- -- SN65LVDS9638D -- SN65LVDS9638DGN -- -- -- -- -- SN65LVDS9638DGK -- -- -- SNJ55LVDS31J SNJ55LVDS31W SN55LVDS31W -55C to 125C (1) (D) -- -- -- SNJ55LVDS31FK For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. 'LVDS31 logic diagram (positive logic) logic symbol SN55LVDS31, SN65LVDS31 G G 1A 2A 3A 4A 2 4 12 1 7 1 G G EN 1A 2 3 6 5 9 10 11 15 14 13 1Y 2A 4 12 1 3 7 3A 9 3Z 4Y 4Z This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Submit Documentation Feedback 4A 10 11 2Z 3Y 6 5 1Z 2Y 2 15 14 13 1Y 1Z 2Y 2Z 3Y 3Z 4Y 4Z SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 SN65LVDS3487 logic diagram (positive logic) logic symbol SN65LVDS3487 1,2EN 1A 2A 3,4EN 3A 4A 4 EN 2 1 3 6 7 12 5 1Y 2Y 11 14 15 5 2Z 13 3,4EN 3Y 3Z 4A 9 10 11 1Z 2Y 2Z 3Y 3Z 12 15 14 13 4Y 4Y 4Z 4Z This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. SN65LVDS9638 logic diagram (positive logic) logic symbol SN65LVDS9638 1A 2A 6 7 3A 10 1Y 4 2A EN 9 3 1,2EN 1Z 2 1 1A 2 3 8 7 6 5 1Y 1A 2 7 1Z 2Y 2Z 2A 8 3 6 5 1Y 1Z 2Y 2Z This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Submit Documentation Feedback 3 SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 FUNCTION TABLES SN55LVDS31, SN65LVDS31 (1) (1) ENABLES OUTPUTS INPUT A G G Y H H X H L L H X L H H X L H L L X L L H Z X L H Z Z Open H X L H Open X L L H H = high level, L = low level, X = irrelevant, Z = high impedance (off) SN65LVDS3487 (1) (1) INPUT A ENABLE EN H H OUTPUTS Y Z H L H L H L X L Z Z Open H L H H = high level, L = low level, X = irrelevant, Z = high impedance (off) SN65LVDS9638 (1) INPUT A (1) 4 OUTPUTS Y Z H H L L L H Open L H H = high level, L = low level Submit Documentation Feedback SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 EQUIVALENT INPUT AND OUTPUT SCHEMATIC DIAGRAMS EQUIVALENT OF EACH A INPUT EQUIVALENT OF G, G, 1,2EN OR 3,4EN INPUTS VCC VCC TYPICAL OF ALL OUTPUTS VCC 50 50 Input Input 10 k 5 Y or Z Output 7V 7V 300 k 7V ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) UNIT VCC Supply voltage range (2) VI Input voltage range -0.5 V to 4 V -0.5 V to VCC + 0.5 V Continuous total power dissipation See Dissipation Rating Table Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds Tstg (1) (2) 260C Storage temperature range -65C to 150C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages, except differential I/O bus voltages, are with respect to the network ground terminal. DISSIPATION RATING TABLE (1) (2) PACKAGE TA 25C POWER RATING DERATING FACTOR (1) ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING TA = 125C POWER RATING D (8) 725 mW 5.8 mW/C 464 mW 377 mW -- D (16) 950 mW 7.6 mW/C 608 mW 494 mW -- DGK 425 mW 3.4 mW/C 272 mW 221 mW -- DGN (2) 2.14 W 17.1 mW/C 1.37 W 1.11 W -- FK 1375 mW 11.0 mW/C 880 mW 715 mW 275 mW J 1375 mW 11.0 mW/C 880 mW 715 mW 275 mW PW (16) 774 mW 6.2 mW/C 496 mW 402 mW -- W 1000 mW 8.0 mW/C 640 mW 520 mW 200 mW This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. The PowerPADTM must be soldered to a thermal land on the printed-circuit board. See the application note PowerPAD Thermally Enhanced Package (SLMA002). Submit Documentation Feedback 5 SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 RECOMMENDED OPERATING CONDITIONS MIN NOM VCC Supply voltage 3 VIH High-level input voltage 2 VIL Low-level input voltage TA Operating free-air temperature 3.3 MAX 3.6 UNIT V V 0.8 SN65 prefix -40 85 SN55 prefix -55 125 V C SN55LVDS31 ELECTRICAL CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) VOD Differential output voltage magnitude RL = 100 , See Figure 2 247 VOD Change in differential output voltage magnitude between logic states RL = 100 , See Figure 2 -50 VOC(SS) Steady-state common-mode output voltage See Figure 3 1.125 VOC(SS) Change in steady-state common-mode output voltage between logic states See Figure 3 -50 VOC(PP) Peak-to-peak common-mode output voltage See Figure 3 VI = 0.8 V or 2 V, Enabled, No load VI = 0.8 or 2 V, RL = 100 , Enabled VI = 0 or VCC, Disabled ICC Supply current IIH High-level input current VIH = 2 IIL Low-level input current IOS Short-circuit output current IOZ High-impedance output current VO = 0 or 2.4 V IO(OFF) Power-off output current VCC = 0, Ci Input capacitance (1) 340 1.2 MAX UNIT 454 mV 50 mV 1.375 V 50 mV 50 150 mV 9 20 25 35 mA 0.25 1 4 20 A VIL = 0.8 V 0.1 10 A VO(Y) or VO(Z) = 0 -4 -24 12 VOD = 0 VO = 2.4 V mA 1 A 4 A 3 pF All typical values are at TA = 25C and with VCC = 3.3 V. SN55LVDS31 SWITCHING CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER tPLH Propagation delay time, low-to-high-level output tPHL Propagation delay time, high-to-low-level output tr Differential output signal rise time (20% to 80%) tf Differential output signal fall time (80% to 20%) tsk(p) tsk(o) MIN TYP (1) MAX 0.5 1.4 4 ns UNIT 1 1.7 4.5 ns 0.4 0.5 1 ns 0.4 0.5 1 ns Pulse skew (|tPHL - tPLH|) 0.3 0.6 ns Channel-to-channel output skew (2) 0.3 0.6 ns tPZH Propagation delay time, high-impedance-to-high-level output 5.4 15 ns tPZL Propagation delay time, high-impedance-to-low-level output 2.5 15 ns tPHZ Propagation delay time, high-level-to-high-impedance output 8.1 17 ns tPLZ Propagation delay time, low-level-to-high-impedance output 7.3 15 ns (1) (2) 6 TEST CONDITIONS RL = 100 , CL = 10 pF, See Figure 2 See Figure 4 All typical values are at TA = 25C and with VCC = 3.3 V. tsk(o) is the maximum delay time difference between drivers on the same device. Submit Documentation Feedback SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 SN65LVDSxxxx ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS SN65LVDS31 SN65LVDS3487 SN65LVDS9638 MIN VOD Differential output voltage magnitude RL = 100 , See Figure 2 247 VOD Change in differential output voltage magnitude between logic states RL = 100 , See Figure 2 -50 VOC(SS) Steady-state common-mode output voltage See Figure 3 1.125 VOC(S Change in steady-state common-mode output See Figure 3 voltage between logic states -50 S) VOC(PP) Peak-to-peak common-mode output voltage SN65LVDS31, SN65LVDS3487 ICC Supply current SN65LVDS9638 UNIT (1) MAX 340 454 mV 50 mV TYP 1.2 See Figure 3 1.37 5 50 mV 50 150 mV 9 20 25 35 1 VI = 0.8 V or 2 V, Enabled, No load VI = 0.8 or 2 V, RL = 100 , Enabled VI = 0 or VCC, Disabled 0.25 No load 4.7 8 9 13 VI = 0.8 V or 2 V RL = 100 V mA mA IIH High-level input current VIH = 2 4 20 A IIL Low-level input current VIL = 0.8 V 0.1 10 A VO(Y) or VO(Z) = 0 -4 -24 IOS Short-circuit output current IOZ High-impedance output current VO = 0 or 2.4 V IO(OFF) Power-off output current VCC = 0, Ci Input capacitance (1) 12 VOD = 0 VO = 2.4 V mA 1 A 1 A 3 pF All typical values are at TA = 25C and with VCC = 3.3 V. SN65LVDSxxxx SWITCHING CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS SN65LVDS31 SN65LVDS3487 SN65LVDS9638 MIN TYP (1) UNIT MAX tPLH Propagation delay time, low-to-high-level output 0.5 1.4 2 ns tPHL Propagation delay time, high-to-low-level output 1 1.7 2.5 ns tr Differential output signal rise time (20% to 80%) 0.4 0.5 0.6 ns tf Differential output signal fall time (80% to 20%) 0.4 0.5 0.6 ns tsk(p) Pulse skew (|tPHL - tPLH|) 0.3 0.6 ns tsk(o) Channel-to-channel output skew (2) 0 0.3 ns RL = 100 , CL = 10 pF, See Figure 2 (3) tsk(pp) Part-to-part skew 800 ps tPZH Propagation delay time, high-impedance-to-high-level output 5.4 15 ns tPZL Propagation delay time, high-impedance-to-low-level output 2.5 15 ns tPHZ Propagation delay time, high-level-to-high-impedance output 8.1 15 ns tPLZ Propagation delay time, low-level-to-high-impedance output 7.3 15 ns (1) (2) (3) See Figure 4 All typical values are at TA = 25C and with VCC = 3.3 V. tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the same direction while driving identical specified loads. tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same supply voltages, same temperature, and have identical packages and test circuits. Submit Documentation Feedback 7 SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 PARAMETER MEASUREMENT INFORMATION IOY Y II A Z IOZ VOD VOY VOC VI (VOY + VOZ)/2 VOZ Figure 1. Voltage and Current Definitions 2V 1.4 V 0.8 V Input tPLH Y Input (see Note A) VOD Z tPHL 100 1% 100% 80% VOD CL = 10 pF (2 Places) (see Note B) 0 20% 0% tf tr NOTES: A. All input pulses are supplied by a generator having the following characteristics: tr or tf 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 0.2 ns. B. CL includes instrumentation and fixture capacitance within 6 mm of the D.U.T. Figure 2. Test Circuit, Timing, and Voltage Definitions for the Differential Output Signal Y Input (see Note A) 49.9 1% (2 Places) 3V A A 0 VOC(PP) Z (see Note C) VOC CL = 10 pF (2 Places) (see Note B) VOC(SS) VOC NOTES: A. All input pulses are supplied by a generator having the following characteristics: tr or tf 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 0.2 ns. B. CL includes instrumentation and fixture capacitance within 6 mm of the D.U.T. C. The measurement of VOC(PP) is made on test equipment with a -3-dB bandwidth of at least 300 MHz. Figure 3. Test Circuit and Definitions for the Driver Common-Mode Output Voltage 8 Submit Documentation Feedback SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 PARAMETER MEASUREMENT INFORMATION (continued) 49.9 1% (2 Places) Y Inputs (see Note A) 0.8 V or 2 V Z 1.2 V G G 1,2EN or 3,4EN CL = 10 pF (2 Places) (see Note B) G, 1,2EN, OR 3,4EN 2V 1.4 V 0.8 V G 2V 1.4 V 0.8 V tPZH VOZ or VOY VOZ tPHZ VOY or VOZ tPZL VOY 100%, 1.4 V 50% 0%, 1.2 V A at 2 V, G at VCC and Input to G or G at GND and Input to G for 'LVDS31 Only 100%, 1.2 V 50% 0%, 1 V A at 0.8 V, G at VCC and Input to G or G at GND and Input to G for 'LVDS31 Only tPLZ NOTES: A. All input pulses are supplied by a generator having the following characteristics: tr or tf < 1 ns, pulse repetition rate (PRR) = 0.5 Mpps, pulse width = 500 10 ns. B. CL includes instrumentation and fixture capacitance within 6 mm of the D.U.T. Figure 4. Enable-/Disable-Time Circuit and Definitions Submit Documentation Feedback 9 SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 TYPICAL CHARACTERISTICS SN55LVDS31, SN65LVDS31 SUPPLY CURRENT vs FREQUENCY LOW-TO-HIGH PROPAGATION DELAY TIME vs FREE-AIR TEMPERATURE 35 I CC - Supply Current - mA 33 t PLH - Low-to-High Propagation Delay Time - ns 1.9 Four Drivers Loaded Per Figure 3 and Switching Simultaneously VCC = 3.6 V 31 29 VCC = 3 V 27 25 VCC = 3.3 V 23 21 19 17 15 50 100 150 200 1.8 1.7 1.6 VCC = 3.3 V 1.5 VCC = 3 V 1.4 VCC = 3.6 V 1.3 1.2 1.1 1 -40 f - Frequency - MHz -20 60 80 0 20 40 TA - Free-Air Temperature - C Figure 5. Figure 6. HIGH-TO-LOW PROPAGATION DELAY TIME vs FREE-AIR TEMPERATURE t PHL - High-to-Low Propagation Delay Time - ns 1.9 1.8 VCC = 3 V 1.7 1.6 VCC = 3.3 V 1.5 VCC = 3.6 V 1.4 1.3 1.2 1.1 1 -40 -20 60 80 0 20 40 TA - Free-Air Temperature - C Figure 7. 10 Submit Documentation Feedback 100 100 SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 APPLICATION INFORMATION The devices are generally used as building blocks for high-speed point-to-point data transmission where ground differences are less than 1 V. Devices can interoperate with RS-422, PECL, and IEEE-P1596. Drivers/receivers approach ECL speeds without the power and dual supply requirements. TRANSMISSION DISTANCE vs SIGNALING RATE Transmission Distance - m 100 30% Jitter (see Note A) 10 5% Jitter (see Note A) 1 24 AWG UTP 96 (PVC Dielectric) 0.1 10 100 1000 Signaling Rate - Mbps A. This parameter is the percentage of distortion of the unit interval (UI) with a pseudorandom data pattern. Figure 8. Typical Transmission Distance Versus Signaling Rate 1 2 ZO = 100 3 VCC 4 5 1A VCC 1Y 4A 1Z 4Y G 4Z 2Z G 16 3.3 V 15 0.1 F (see Note A) 0.001 F (see Note A) 14 13 ZO = 100 12 See Note B ZO = 100 6 7 8 2Y 3Z 2A 3Y GND 3A 11 10 ZO = 100 9 NOTES: A. Place a 0.1-F and a 0.001-F Z5U ceramic, mica, or polystyrene dielectric, 0805 size, chip capacitor between VCC and the ground plane. The capacitors should be located as close as possible to the device terminals. B. Unused enable inputs should be tied to VCC or GND, as appropriate. Figure 9. Typical Application Circuit Schematic Submit Documentation Feedback 11 SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 APPLICATION INFORMATION (continued) 1/4 'LVDS31 Strb/Data_TX Tp Bias on Twisted-Pair A Strb/Data_Enable TP 55 'LVDS32 5 k Data/Strobe 55 3.3 V TP 20 k 500 VG on Twisted-Pair B 1 Arb_RX 500 20 k 3.3 V 500 20 k 2 Arb_RX 500 20 k 3.3 V 7 k Twisted-Pair B Only 7 k 10 k Port_Status 3.3 k NOTES: A. B. C. D. Resistors are leadless, thick film (0603), 5% tolerance. Decoupling capacitance is not shown, but recommended. VCC is 3 V to 3.6 V. The differential output voltage of the 'LVDS31 can exceed that specified by IEEE1394. Figure 10. 100-Mbps IEEE 1394 Transceiver 12 Submit Documentation Feedback SN55LVDS31, SN65LVDS31 SN65LVDS3487, SN65LVDS9638 www.ti.com SLLS261L - JULY 1997 - REVISED JULY 2007 APPLICATION INFORMATION (continued) 0.01 F 1 1A VCC 3.6 V 16 5V 0.1 F (see Note A) 2 ZO = 100 3 VCC 4 5 1Y 4A 1Z 4Y G 4Z 2Z G 1N645 (2 places) 15 14 ZO = 100 13 12 See Note B ZO = 100 6 7 8 2Y 3Z 2A 3Y GND 3A 11 10 ZO = 100 9 A. Place a 0.1-F Z5U ceramic, mica, or polystyrene dielectric, 0805 size, chip capacitor between VCC and the ground plane. The capacitor should be located as close as possible to the device terminals. B. Unused enable inputs should be tied to VCC or GND, as appropriate. Figure 11. Operation With 5-V Supply COLD SPARING Systems using cold sparing have a redundant device electrically connected without power supplied. To support this configuration, the spare must present a high-input impedance to the system so that it does not draw appreciable power. In cold sparing, voltage may be applied to an I/O before and during power up of a device. When the device is powered off, VCC must be clamped to ground and the I/O voltages applied must be within the specified recommended operating conditions. RELATED INFORMATION IBIS modeling is available for this device. Contact the local TI sales office or the TI Web site at www.ti.com for more information. For more application guidelines, see the following documents: * Low-Voltage Differential Signaling Design Notes (SLLA014) * Interface Circuits for TIA/EIA-644 (LVDS) (SLLA038) * Reducing EMI With LVDS (SLLA030) * Slew Rate Control of LVDS Circuits (SLLA034) * Using an LVDS Receiver With RS-422 Data (SLLA031) * Evaluating the LVDS EVM (SLLA033) Submit Documentation Feedback 13 PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Samples (Requires Login) 5962-9762101Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 5962-9762101QEA ACTIVE CDIP J 16 1 TBD Call TI Call TI 5962-9762101QFA ACTIVE CFP W 16 1 TBD Call TI Call TI 5962-9762101VFA ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type SN55LVDS31W ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type SN65LVDS31D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31DR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31DRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31NSR ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31NSRG4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS31QPWQ1 OBSOLETE TSSOP PW 16 TBD Call TI Call TI SN65LVDS31QPWRQ1 OBSOLETE TSSOP PW 16 TBD Call TI Call TI SN65LVDS3487D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS3487DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS3487DR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 5-Sep-2011 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGK ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGKG4 ACTIVE MSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGKR ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGKRG4 ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGN ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGNR ACTIVE MSOPPowerPAD DGN 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DGNRG4 ACTIVE MSOPPowerPAD DGN 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65LVDS9638DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SNJ55LVDS31FK ACTIVE LCCC FK 20 1 TBD SNJ55LVDS31J ACTIVE CDIP J 16 1 TBD SNJ55LVDS31W ACTIVE CFP W 16 1 TBD SNLVDS9638DGNG4 ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) POST-PLATE N / A for Pkg Type A42 N / A for Pkg Type A42 N / A for Pkg Type CU NIPDAU Level-1-260C-UNLIM The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 2 Samples (Requires Login) SN65LVDS3487DRG4 (1) (3) PACKAGE OPTION ADDENDUM www.ti.com 5-Sep-2011 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN55LVDS31, SN55LVDS31-SP : * Catalog: SN75LVDS31, SN55LVDS31 * Space: SN55LVDS31-SP NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 13-Dec-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN65LVDS31DR Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN65LVDS31NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 SN65LVDS31PWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 SN65LVDS3487DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN65LVDS9638DGKR MSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 SN65LVDS9638DGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 SN65LVDS9638DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 SN65LVDS9638DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 13-Dec-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65LVDS31DR SOIC D 16 2500 333.2 345.9 28.6 SN65LVDS31NSR SO NS 16 2000 346.0 346.0 33.0 SN65LVDS31PWR TSSOP PW 16 2000 346.0 346.0 29.0 SN65LVDS3487DR SOIC D 16 2500 346.0 346.0 33.0 SN65LVDS9638DGKR MSOP DGK 8 2500 358.0 335.0 35.0 SN65LVDS9638DGNR MSOP-PowerPAD DGN 8 2500 358.0 335.0 35.0 SN65LVDS9638DR SOIC D 8 2500 340.5 338.1 20.6 SN65LVDS9638DR SOIC D 8 2500 346.0 346.0 29.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connctivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated