3.5x2.8mm PHOTOTRANSISTOR Part Number: AA3528P3S Description Features z Mechanically and spectrally matched to the infrared emitting Made with NPN silicon phototransistor chips. LED lamp. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. 4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. 5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871 Electrical / Optical Characteristics at TA=25C Symbol Parameter Min. VBR CEO Collector-to-Emitter Breakdown Voltage VBR ECO Emitter-to-Collector Breakdown Voltage VCE (SAT) Collector-to-Emitter Saturation Voltage Collector Dark Current I CEO Typ. Max. Units Test Conditions 30 V IC=100uA Ee=0mW/cm2 5 V IE=100uA Ee=0mW/cm2 0.8 V IC=2mA Ee=20mW/cm2 100 nA VCE=10V Ee=0mW/cm2 TR Rise Time (10 to 90 ) 15 us TF Fall Time (90 to 10 ) 15 us 0.4 mA I (ON) On State Collector Current 0.2 0.1 Range of spectral bandwidth 420 p 1120 VCE = 5V Ee=1mW/cm2 =940nm nm Wavelength of peak sensitivity 940 nm Angle of half sensitivity 120 deg 21/2 VCE = 5V IC=1mA RL=1000 Absolute Maximum Ratings at TA=25C Parameter Max.Ratings Collector-to-Emitter Voltage 30V Emitter-to-Collector Voltage 5V Power Dissipation at (or below) 25C Free Air Temperature 100mW Operating Temperature -40C To +85C Storage Temperature -40C To +85C Note: 1. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity - Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871 SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871 AA3528P3S Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871 PACKING & LABEL SPECIFICATIONS AA3528P3S Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kingbright: AA3528P3S