1100 DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC1206 5%, 1%, 0.5%, 0.1% Product specification - June 25, 2014 V.5 RoHS compliant Product specification Chip Resistor Surface Mount RC 2 9 1206 (RoHS Compliant) SERIES SCOPE ORDERING INFORMATION - GLOBAL PART NUMBER & 12NC This specification describes RC1206 series chip resistors with lead-free terminations made by thick film process. Both part numbers are identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. YAGEO BRAND ordering code GLOBAL PART NUMBER (PREFERRED ) APPLICATIONS All general purpose application RC1206 (1) (2) (3) (4) - Products with lead free terminations meet RoHS requirements Pb-glass contained in electrodes, resistor element and glass are exempted by RoHS Reducing environmentally hazardous wastes High component and equipment reliability Saving of PCB space None forbidden-materials used in products/production (6) B = 0.1% D = 0.5% F = 1% RoHS compliant - (5) (1) TOLERANCE FEATURES Halogen Free Epoxy X R - XX XXXX L J = 5% (for Jumper ordering, use code of J) (2) PACKAGING TYPE R = Paper taping reel (3) TEMPERATURE COEFFICIENT OF RESISTANCE - = Base on spec (4) TAPING REEL 07 = 7 inch dia. Reel 13 = 13 inch dia. Reel (5) RESISTANCE VALUE There are 2~4 digits indicated the resistor value. Letter R/K/M is decimal point, no need to mention the last zero after R/K/M, e.g.1K2, not 1K20. Detailed resistance rules show in table of "Resistance rule of global part number". (6) DEFAULT CODE Letter L is system default code for order only (Note) Resistance rule of global part number Resistance code rule Example 0R 0R = Jumper XRXX (1 to 9.76 ) 1R = 1 1R5 = 1.5 9R76 = 9.76 XXRX (10 to 97.6 ) 10R = 10 97R6 = 97.6 XXXR (100 to 976 ) 100R = 100 XKXX (1 to 9.76 K) 1K = 1,000 9K76 = 9760 XMXX (1 to 9.76 M) 1M = 1,000,000 9M76= 9,760,000 ORDERING EXAMPLE The ordering code of a RC1206 chip resistor, value 56 X with 1% tolerance, supplied in 7-inch tape reel is: RC1206FR-0756RL. NOTE 1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label, "LFP" or specific symbol can be printed www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 3 9 1206 (RoHS Compliant) PHYCOMP BRAND ordering codes Both GLOBAL PART NUMBER (preferred) and 12NC (traditional) codes are acceptable to order Phycomp brand products. GLOBAL PART NUMBER (PREFERRED ) For detailed information of GLOBAL PART NUMBER and ordering example, please refer to page 2. 12NC CODE 2322 / 2350 XXX XXXXX L (1) (2) (3) Last digit of 12NC Resistance decade (3) (4) TYPE/ START TOL. RESISTANCE 1206 IN (1) (%) RANGE PAPER / PE TAPE ON REEL (units) 5,000 10,000/not preferred (2) 20,000 Last digit 0.01 to 0.0976 X 0.1 to 0.976 X 0 8 7 RC01 2322 5% 1 to 10 M 711 61xxx 711 51xxx 711 81xxx 1 to 9.76 X RC02 2322 1% 1 to 10 M 724 6xxxx 724 7xxxx 724 8xxxx 10 to 97.6 X 9 HRC01 2350 5% 11 to 22 M 520 10xxx - - 100 to 976 X 1 Jumper 2322 - 711 91032 711 91005 711 92004 1 to 9.76 KX 2 0 10 to 97.6 KX 3 (1) The resistors have a 12-digit ordering code starting with 2322 / 2350. 100 to 976 KX 4 (2) The subsequent 4 or 5 digits indicate the resistor tolerance and packaging. 1 to 9.76 MX 5 10 to 97.6 MX 6 (3) The remaining 4 or 3 digits represent the resistance value with the last digit indicating the multiplier as shown in the table of "Last digit of 12NC". (4) Letter L is system default code for order only (Note) ORDERING EXAMPLE The ordering code of a RC02 resistor, value 56 X with 1% tolerance, supplied in tape of 10,000 units per reel is: 232272465609L or RC1206FR-0756RL. Example: 0.02 X 0.3 X = 0200 or 200 = 3007 or 307 1X = 1008 or 108 33 KX 10 MX = 3303 or 333 = 1006 or 106 NOTE 1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label, "LFP" or specific symbol can be printed www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 4 9 1206 (RoHS Compliant) MARKING RC1206 E-24 series: 3 digits Fig. 1 Value = 10 K First two digits for significant figure and 3rd digit for number of zeros Both E-24 and E-96 series: 4 digits Fig. 2 Value = 10 K First three digits for significant figure and 4th digit for number of zeros For further marking information, please see special data sheet "Chip resistors marking" CONSTRUCTION The resistor is constructed on top of a high-grade ceramic body. Internal metal electrodes are added on each end to make the contacts to the thick film resistive element. The composition of the resistive element is a noble metal imbedded into a glass and covered by a second glass to prevent environment influences. The resistor is laser trimmed to the rated resistance value. The resistor is covered with a protective epoxy coat, finally the two external terminations (matte tin on Nibarrier) are added. See fig.3 OUTLINES For dimension see Table 1 DIMENSIONS Table 1 TYPE RC1206 L (mm) 3.10 0.10 W (mm) 1.60 0.10 H (mm) 0.55 0.10 I1 (mm) 0.45 0.20 I2 (mm) 0.40 0.20 Fig. 3 Chip resistor outlines www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 1206 (RoHS Compliant) ELECTRICAL CHARACTERISTICS 5 9 FOOTPRINT AND SOLDERING PROFILES Table 2 RC1206 1/4 W CHARACTERISTICS Operating Temperature Range -55 C to +155 C Maximum Working Voltage 200 V Maximum Overload Voltage 400 V Dielectric Withstanding Voltage 500 V For recommended footprint and soldering profiles, please see the special data sheet "Chip resistors mounting". 5% (E24) 1 to 22 M 1% (E24/E96) 1 to 10 M Resistance Range 0.1%, 0.5% (E24/E96) 10 to 1 M Zero Ohm Jumper < 0.05 Temperature Coefficient 1 R 10 200 ppm/C 10 M < R 22 M 200 ppm/C 10 < R 10 M 100 ppm/C Rated Current 2A Maximum Current 10 A Jumper Criteria PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PRODUCT TYPE PACKING STYLE REEL DIMENSION QUANTITY PER REEL RC1206 Paper Taping Reel (R) 7" (178 mm) 5,000 units 13" (330 mm) 20,000 units NOTE 1. For paper tape and reel specification/dimensions, please see the special data sheet "Chip resistors packing" FUNCTIONAL DESCRIPTION POWER RATING RC1206 rated power at 70C is 1/4 W RATED VOLTAGE The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V=(P X R) or max. working voltage whichever is less Where V=Continuous rated DC or AC (rms) working voltage (V) Fig. 4 Maximum dissipation (P) in percentage of rated power as a function of the operating ambient temperature (T amb ) P=Rated power (W) R=Resistance value (X) www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 6 9 1206 (RoHS Compliant) TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature Coefficient of Resistance (T.C.R.) IEC 60115-1 4.8 At +25/-55 C and +25/+125 C Refer to table 2 Formula: R2-R1 T.C.R= ------------------------- x 106 (ppm/C) R1(t2-t1) Where t1=+25 C or specified room temperature t2=-55 C or +125 C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms Life/Endurance IEC 60115-1 4.25.1 At 70 5 C for 1,000 hours, RCWV applied for 1.5 hours on, 0.5 hour off, still air required (1.0%+0.05 ) for 0.1%, 0.5%, 1% tol. (3.0%+0.05 ) for 5% tol. <100 m for Jumper High Temperature Exposure/ Endurance at Upper Category Temperature IEC 60068-2-2 Moisture Resistance MIL-STD-202G Method-106G 1,000 hours at 155 5 C, unpowered (1.0%+0.05 ) for 0.1%, 0.5%, 1% tol. (2.0%+0.05 ) for 5% tol. <50 m for Jumper Each temperature / humidity cycle is defined at 8 hours, 3 cycles / 24 hours for 10d. with 25 C / 65 C 95% R.H, without steps 7a & 7b, unpowered Parts mounted on test-boards, without condensation on parts (0.5%+0.05 ) for 0.1%, 0.5%, 1% tol. (2.0%+0.05 ) for 5% tol. <100 m for Jumper Measurement at 24 2 hours after test conclusion Thermal Shock MIL-STD-202G Method-107G -55/+125 C Number of cycles required is 300. Devices unmounted Short Time Overload IEC60115-1 4.13 (0.5%+0.05 ) for 0.1%, 0.5%, 1% tol. (1%+0.05 ) for 5% tol. Maximum transfer time is 20 seconds. Dwell time is 15 minutes. Air - Air <50 m for Jumper 2.5 times of rated voltage or maximum overload voltage whichever is less for 5 sec at room temperature (1.0%+0.05 ) for 0.1%, 0.5%, 1% tol. (2.0%+0.05 ) for 5% tol. <50 m for Jumper No visible damage www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 7 9 1206 (RoHS Compliant) TEST TEST METHOD PROCEDURE REQUIREMENTS Board Flex/ Bending IEC 60068-2-21 Chips mounted on a 90mm glass epoxy resin PCB (FR4) (1.0%+0.05 ) for 0.1%, 0.5%, 1% , 5% tol. 2 mm bending <50 m for Jumper Bending time: 60 5 seconds No visible damage The resistor shall be subjected to a DC rated voltage for 1.5 h-on, 0.5 h-off, at -55 3 C (0.5%+0.05 ) for 0.1%, 0.5%, 1% tol. This constitutes shall be repeated for 96 hours (1.0%+0.05 ) for 5% tol. However the applied voltage shall not exceed the maximum operating voltage No visible damage Rated continuous overload voltage (RCOV) for 1 minute 10 G Low Temperature Operation Insulation Resistance IEC 60068-2-1 IEC 60115-1 4.6 Type Voltage (DC) Dielectric Withstand Voltage IEC 60115-1 4.7 Resistance to Solvent IPC/JEDEC J-STD-020D Noise Biased Humidity (steady state) IEC 60115-1 4.12 IEC 60115-1 4.37 RC1206 100 V Maximum voltage (Vrms) applied for 1 minute Type RC1206 Voltage (AC) 500 Vrms No breakdown or flashover lsopropylalcohol (C3H7OH) followed by brushing No smeared Maximum voltage (Vrms) applied Resistors range Value R < 100 10 dB 100 R < 1 K 20 dB 1 K R < 10 K 30 dB 10 K R < 100 K 40 dB 100 K R < 1 M 46 dB 1 M R 22 M 48 dB Steady state for 1000 hours at 40 C / 95% R.H. RCWV applied for 1.5 hours on and 0.5 hour off (1.0%+0.05 ) for 0.1%, 0.5%, 1% tol. (2.0%+0.05 ) for 5% tol. <100 m for Jumper www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 8 9 1206 (RoHS Compliant) TEST TEST METHOD PROCEDURE REQUIREMENTS Intermittent Overload IEC 60115-1 4.39 2.5 times of rated voltage or maximum overload voltage whichever is less for 1 second on and 25 seconds off; total 10,000 cycles (1.0%+0.05 ) for 0.1%, 0.5%, 1% tol. (2.0%+0.05 ) for 5% tol. <100 m for Jumper Solderability - Wetting IPC/JEDEC J-STD-002B test B Electrical Test not required Well tinned (95% covered) Magnification 50X No visible damage SMD conditions: 1st step: method B, aging 4 hours at 155 C dry heat 2nd step: leadfree solder bath at 245 3 C Dipping time: 3 0.5 seconds - Leaching IPC/JEDEC J-STD-002B test D Leadfree solder, 260 C, 30 seconds immersion time No visible damage - Resistance to Soldering Heat IEC 60068-2-58 Condition B, no pre-heat of samples (0.5%+0.05 ) for 0.1%, 0.5%, 1% tol. Leadfree solder, 260 C, 10 seconds immersion time Procedure 2 for SMD: devices fluxed and cleaned with isopropanol (1.0%+0.05 ) for 5% tol. <50 m for Jumper No visible damage www.yageo.com Jun. 25, 2014 V.5 Product specification Chip Resistor Surface Mount RC SERIES 9 9 1206 (RoHS Compliant) REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 5 - Jun. 25, 2014 - Test Items and methods updated - Test requirements upgraded Version 4 Jul 02, 2009 - - Test Items and methods updated - Test requirements upgraded Version 3 Jul 15, 2008 - - Change to dual brand datasheet that describe RC1206 with RoHS compliant - Description of "Halogen Free Epoxy" added - Define global part number Version 2 Sep 03, 2004 - - New datasheet for 1206 thick film 1% and 5% with lead-free terminations - Replace the 1206 part of pdf files: RC01_11_21_31_5, RC02_12_22_32_10, and HRC01_5_4 - Test method and procedure updated - PE tape added (paper tape will be replaced by PE tape) - High ohmic products combined into standard products. " Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any product change will be announced by PCN." www.yageo.com Jun. 25, 2014 V.5