19-3960; Rev 1; 6/01 Quad SPST CMOS Analog Switches Features Guaranteed 4.5V to 18V Operation No VL Supply Required Nonlatching with Supplies Turned Off and Input Signals Present CMOS and TTL Logic Compatible Monolithic, Low-Power CMOS Design Ordering Information PART TEMP RANGE PIN-PACKAGE DG202CUE 0C to +70C 16 TSSOP DG202CSE 0C to +70C 16 SO DG202CJ 0C to +70C 16 Plastic DIP 0C to +70C Dice DG202C/D DG202AEGE -40C to +85C 16 QFN (5 x 5) DG202AEUE -40C to +85C 16 TSSOP DG202ADY -40C to +85C 16 SO DG202ADJ -40C to +85C 16 Plastic DIP Analog Multiplexers DG202AAK DG212CUE -55C to +125C 0C to +70C 16 CERDIP 16 TSSOP Programmable Gain Amplifiers DG212CSE 0C to +70C Communications Systems DG212CJ 0C to +70C 16 Plastic DIP Sample/Holds DG212C/D 0C to +70C Dice DG212EGE -40C to +85C DG212EUE DG212DY -40C to +85C -40C to +85C DG212DJ -40C to +85C Applications Automatic Test Equipment PBX, PABX Typical Operating Circuit 5k 5k VIN x 10V * 1 16 * 2 15 3 14 -15V 4 5 DG202 DG212 6 7 10k * 8 13 +15V 12 11 10 9 * PROGRAMMABLE GAIN AMPLIFIER NOTE: *PINS 1, 8, 9, AND 16 ARE LOGIC CONTROL INPUTS 40k VOUT 16 SO 16 QFN (5 x 5) 16 TSSOP 16 SO 16 Plastic DIP Pin Configurations IN1 1 16 IN2 D1 2 15 D2 S1 3 14 S2 V- 4 GND 5 S4 6 11 S3 D4 7 10 D3 IN4 8 13 V+ DG202 DG212 12 V L 9 20k IN3 DIP/SO LOGIC SWITCH 0 1 OFF ON SWITCHES SHOWN FOR LOGIC "0" INPUT Pin Configurations continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 DG202/DG212 General Description The DG202 and DG212 are normally open, quad single-pole single-throw (SPST) analog switches. These CMOS switches can be continuously operated with power supplies ranging from 4.5V to 18V. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. The DG202/DG212 are similar to the DG201/DG211 except for inverted control inputs. All devices have guaranteed break-before-make switching, as well as essentially constant on-resistance over the analog signal range. All switches conduct current in either direction and add no offset to the output signal. Compared to the original manufacturer's products, Maxim's DG202 and DG212 consume very little power, making them better suited for portable applications. Maxim has also eliminated the need for the third logic power supply (VL) that is required for the operation of the original manufacturer's DG212 without sacrificing compatibility. DG202/DG212 Quad SPST CMOS Analog Switches ABSOLUTE MAXIMUM RATINGS (DG212) V+ to V-.......................................................................44V VIN to Ground.................................................... .........V-, V+ VL to Ground.........................................................-0.3V, 25V VS or VD to V+............................................................0, -40V VS or VD to V-..............................................................0, 40V V+ to Ground....................................................................25V V- to Ground.................................................................-25V Current, Any Terminal Except S or D...............................30mA Continuous Current, S or D............................................20mA Peak Current, S or D (pulsed at 1ms 10% duty cycle max).............................70mA Storage Temperature Range.........................-65C to +125C Operating Temperature Range DG211C ...........................................................0C to +70C DG211D/E ....................................................-40C to +85C Power Dissipation (TA = +70C) (Note 1) 16-Pin Plastic Dip (derate 10.5mW/C above +70C) ..842mW 16-Pin Narrow SO (derate 8.7mW/C above+70C). ....696mW 16-Pin TSSOP (derate 9.4mW/C above +70C) ..........755mW 16-Pin QFN (5 5) (derate 19.2mW/C above +70C) .........................1538mW Note 1: Device mounted with all leads soldered to PC board. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (DG212) (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 2.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SWITCH Analog Signal Range VANALOG Drain-Source ON-Resistance RDS (ON) -15 Source OFF-Leakage Current IS (OFF) VIN = 0.8V Drain OFF-Leakage Current ID (OFF) VIN = 0.8V Drain ON-Leakage Current (Note 3) ID (ON) VD = 10V, VIN = 2.4V, IS = 1mA VS = 14V, VD = -14V VS = -14V, VD = 14V -5.0 VS = 14V, VD = -14V VS = -14V, VD = 14V +15 V 115 175 0.01 5.0 -0.02 0.01 -5.0 -0.02 VS = VD = -14V, VIN = 2.4V -5.0 -0.15 VIN = 2.4V -1.0 -0.0004 VS = VD = 14V, VIN = 2.4V 0.1 5.0 nA 5.0 INPUT Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL VIN = 15V VIN = 0 0.003 -1.0 1.0 A -0.0004 DYNAMIC Turn-ON Time Turn-OFF Time Source OFF-Capacitance Drain OFF-Capacitance Channel ON-Capacitance OFF-Isolation (Note 4) Crosstalk (Channel to Channel) 2 tON tOFF1 tOFF2 See Switching Time Test Circuit VS = 2V, RL = 1k, CL = 35pF 460 1000 360 500 CS (OFF) VS = 0, VIN = 0, f = 1MHz CD (OFF) VD = 0, VIN = 0, f = 1MHz 5 VD = VS = 0, VIN = 5V, f = 1MHz 16 CD + S (ON) OIRR CCRR ns 450 5 pF 70 VIN = 0, RL = 1k, CL = 15pF, VS = 1VRMS, f = 100kHz 90 _______________________________________________________________________________________ dB Quad SPST CMOS Analog Switches (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 2.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX 0.02 0.4 0.01 0.4 0 0 UNITS SUPPLY Positive Supply Current I+ Negative Supply Current I- Logic Supply Current IL Power-Supply Range for Continous Operation VIN = 0 and 2.4V (all) VOP 4.5 18 mA V Note 2: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Note 3: ID(ON) is leakage from driver into "ON" switch. Note 4: OFF-Isolation = 20 log VS/VD, VS = input to OFF switch, VD = output. ABSOLUTE MAXIMUM RATINGS (DG202) Voltages Reference to VV+.........................................................................44V GND......................................................................25V Digital Inputs (Note 1), VS, VD ............................-2V to (V+ + 2V) or 20mA, whichever occurs first Current, Any Terminal Except S or D..............................30mA Continuous Current, S or D..........................................20mA Peak Current, S or D (pulsed at 1ms 10% duty cycle max).........................70mA Operating Temperature Range DG202C .........................................................0C to +70C DG202D/E..................................................-40C to +85C DG202A .....................................................-55C to +125C Storage Temperature Range.........................-65C to +150C Power Dissipation (Note 2) 16-Pin Plastic Dip (derate 10.5mW/C above +70C) ...842mW 16-Pin SO (derate 8.7mW/C above +70C) .................696mW 16-Pin TSSOP (derate 9.4mW/C above +70C) ...........755mW 16-Pin QFN (5 5) (derate 19.2mW/C above +70C)...........................1538mW 16-Pin CERDIP (derate 10.0mW/C above +70C)......800mW Note 1: Signals on S_, D_, or IN_ exceeding V+ or V- on Maxim's DG202 will be clamped by internal diodes, and are also internally current limited to 25mA. Note 2: Device mounted with all leads soldered to PC board. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (DG202) (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 3.) PARAMETER SYMBOL CONDITIONS DG202A MIN TYP DG202C, D, E MAX MIN 15 -15 TYP MAX UNITS SWITCH Analog Signal Range VANALOG Drain-Source ON Resistance RDS (ON) -15 VD = 10V, VIN = 2.4V, IS = 1mA Source OFF-Leakage Current IS (OFF) VIN = 0.8V Drain OFF-Leakage Current ID (OFF) VIN = 0.8V Drain ON-Leakage Current (Note 4) ID (ON) VIN = 2.4V VS = 14V, VD = -14V VS = -14V, VD = 14V VS = -14V, VD = 14V VS = 14V 175 115 200 1.0 0.01 5.0 -1.0 -0.02 0.01 0.1 -1.0 115 -0.02 VS = -14V V 0.01 -1.0 VS = 14V, VD = -14V 15 -1.0 -0.02 -1.0 -0.02 1.0 0.01 1.0 0.1 5.0 nA 1.0 -5.0 _______________________________________________________________________________________ 3 DG202/DG212 ELECTRICAL CHARACTERISTICS (DG212) (continued) DG202/DG212 Quad SPST CMOS Analog Switches ELECTRICAL CHARACTERISTICS (DG202) (continued) (V+ = +15V, V- = -15V, GND = 0, TA = +25C, unless otherwise noted.) (For more information on TYP values see Note 3.) PARAMETER SYMBOL CONDITIONS DG202A MIN TYP DG202C, D, E MAX MIN TYP -1.0 -0.0004 MAX UNITS INPUT Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL VIN = 2.4V -1.0 -0.0004 VIN = 15V 0.003 VIN = 0 1.0 -1.0 -0.0004 0.003 -1.0 1.0 A -0.0004 DYNAMIC Turn-ON Time tON Turn-OFF Time tOFF1 Charge Injection Q See Figure 1 Switching Time Test Circuit CL = 1000pF, VGEN = 0, RGEN = 0 Source OFF-Capacitance CS (OFF) Drain OFF-Capacitance CD (OFF) Channel ON-Capacitance CD (ON) VD = VS = 0, + CS (ON) VIN = 5V 480 600 480 600 370 450 370 450 20 VS = 0, VIN = 0 20 5 5 5 5 ns pC f = 140kHz pF 16 16 OFF-Isolation VIN = 0, ZL = 75 70 70 Crosstalk (Channel to Channel) VS = 2.0V, f = 100kHz 90 90 dB SUPPLY Positive Supply Current I+ All channels ON or OFF Negative Supply Current I- All channels ON or OFF Power-Supply Range for Continuous Operation VOP 0.02 -0.1 4.5 0.1 -0.01 0.02 -0.1 18 4.5 Note 3: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Note 4: ID (ON) is leakage from driver into "ON" switch. 4 _______________________________________________________________________________________ 0.1 -0.01 18 mA V Quad SPST CMOS Analog Switches (V+ = +15V, V- = -15V, GND = 0, TA = full opearting temperature range, unless otherwise noted.) (For more information on TYP values see Note 3.) PARAMETER SYMBOL DG202A CONDITIONS MIN TYP DG202C, D, E MAX MIN +15 -15 TYP MAX UNITS SWITCH Analog Signal Range VANALOG -15 Drain-Source ON Resistance (Note 5) RDS (ON) Source OFF-Leakage Current IS (OFF) VIN = 0.8V Drain OFF-Leakage Current ID (OFF) VIN = 0.8V Drain ON-Leakage Current (Note 6) ID (ON) VIN = 2.4V VD = 10V, VIN = 2.4V, IS = 1mA 250 VS = 14V, VD = -14V VS = -14V, VD = 14V 100 -100 250 100 100 -100 100 -100 VS = -14V 200 VD = 14V V -100 VS = 14V, VD = -14V VS = -14V, VD = 14V +15 -200 nA 200 -200 INPUT Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL VIN = 2.4V -1.0 -1.0 VIN = 15V 1.0 VIN = 0 -1.0 1.0 A -1.0 Note 5: Electrical characteristics, such as ON-Resistance, will change when power supplies other than 15V, are used. Note 6: ID (ON) is leakage from driver into "ON" switch. Pin Description PIN NAME FUNCTION DIP/SO/TSSOP QFN 1, 16, 9, 8 15, 14, 7, 6 IN1-IN4 Input 2, 15, 10, 7 16, 13, 8, 5 D1-D4 Analog Switch Drain Terminal 3, 14, 11, 6 1, 12, 9, 4 S1-S4 Analog Switch Source Terminal 4 2 V- Negative-Supply Voltage Input 5 3 GND 12 10 N.C. 13 11 V+ Ground No Connection Positive-Supply Voltage Input--Connected to Substrate Switching Time Test Circuit Switch output waveform shown for VS = constant with logic input waveform as shown. Note that VS may be +ve or -ve as per switching times test circuit. VO is the steady state output with switch on. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. Protecting Against Fault Conditions Fault conditions occur when power supplies are turned off when input signals are still present, or when overvoltages occur at the inputs during normal operation. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. If _______________________________________________________________________________________ 5 DG201A/DG211 ELECTRICAL CHARACTERISTICS (DG202) DG202/DG212 Quad SPST CMOS Analog Switches RL RL + rDS(ON) VO = V S LOGIC INPUT LOGIC 1 SW ON +15V 3V t r < 20ns t f < 20ns SWITCH INPUT 50% V+ 0 VS = +2V SWITCH INPUT VS SWITCH OUTPUT VO 0.9 VO 0.9 VO tOFF1 0 tOFF LOGIC INPUT S1 SWITCH OUTPUT VO D1 IN1 CL 35pF RL 1k 0.1 GND tOFF2 V- (REPEAT TEST FOR IN2, IN3, AND IN4) -15V 0V Figure 1. Switching Time Typical RDS(ON) vs. Power Supplies for Maxim's DG202, and DG212 RDS(ON) AT ANALOG SIGNAL LEVEL POWER SUPPLIES -5V +5V -10V +10V -15V 5V 350 380 -- -- -- -- 10V -- -- 165 250 -- -- 15V -- -- 125 160 135 155 this current is required to be kept to low (A) levels then the addition of external protection diodes is recommended. To provide protection for overvoltages up to 20V above the supplies, a 1N4001 or 1N914 type diode should be placed in series with the positive and negative supplies as shown in Figure 2. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. Pin Configurations (continued) TOP VIEW S1 1 V- 2 GND S4 D1 IN1 IN2 D2 16 15 14 13 12 S2 11 V+ 3 10 N.C. 4 9 S3 DG202 DG212 5 6 7 8 D4 IN4 IN3 D3 IN4001 -15V 1 16 2 15 14 3 4 5 DG202 DG212 13 12 6 11 7 10 8 9 Figure 2. Protection against Fault Conditions QFN 6 _______________________________________________________________________________________ +15V IN4001 +15V Quad SPST CMOS Analog Switches N E H INCHES MILLIMETERS MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050 MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 SOICN .EPS DIM A A1 B C e E H L 1.27 VARIATIONS: 1 INCHES TOP VIEW DIM D D D MIN 0.189 0.337 0.386 MAX 0.197 0.344 0.394 MILLIMETERS MIN 4.80 8.55 9.80 MAX 5.00 8.75 10.00 N MS012 8 AA 14 AB 16 AC D A B e C 0 -8 A1 L FRONT VIEW SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .150" SOIC APPROVAL DOCUMENT CONTROL NO. 21-0041 REV. B 1 1 _______________________________________________________________________________________ 7 DG202/DG212 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) DG202/DG212 Quad SPST CMOS Analog Switches Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 8 _______________________________________________________________________________________ Quad SPST CMOS Analog Switches CDIPS.EPS _______________________________________________________________________________________ 9 DG202/DG212 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) TSSOP4.40mm.EPS DG202/DG212 Quad SPST CMOS Analog Switches 10 ______________________________________________________________________________________ Quad SPST CMOS Analog Switches 32L QFN.EPS Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 11 (c) 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. DG202/DG212 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)