HIH6030-021-001S - HONEYWELL S&C

Honeywell HumidIcon™ Digital

Humidity/Temperature Sensors

HIH6000 Series

±4.5 %RH Accuracy | ±0.5 °C Temperature Accuracy

Datasheet

2sensing.honeywell.com

HIH6020 HIH6021

HIH6030

HIH6031

Series* Output

type

Supply

voltage

Housing

style Filter Accuracy Output Packaging

HIH6020-021-xxxx

digital 2.3 Vdc to

5.5 Vdc

SIP 4-pin without filter,

non-condensing

±4.5 %RH

I2C100 to 249 units on tape

and boxed, 250 units or

more on tape and reel; or

5 sample pieces on tape

HIH6021-021-xxxx SIP 4-pin with filter,

condensation resistant I2C

HIH6030-021-xxxx SOIC-8 SMD without filter,

non-condensing I2C1000 pieces on tape and

reel; or 5 sample pieces

on tape

HIH6030-000-xxxx SOIC-8 SMD without filter,

non-condensing SPI

HIH6031-021-xxxx SOIC-8 SMD with filter,

condensation resistant I2C1000 pieces on tape and

reel; or 5 sample pieces

on tape

HIH6031-000-xxxx SOIC-8 SMD with filter,

condensation resistant SPI

* See order guide on page 11 for complete catalog listings.

HIH6000 Series Housing, Filter, Output, and Packaging Comparison

INDUSTRY-LEADING RELIABILITY • ACCURACY • PACKAGING • LONG-TERM STABILITY

Honeywell HumidIcon™

Digital Humidity/Temperature Sensors

Honeywell HumidIcon™ Digital Humidity/Temperature Sensors, HIH6000 Series, are digital output-type relative humidity (RH)

and temperature sensors combined in the same package. These sensors provide an accuracy level of ±4.5 %RH and a

temperature accuracy level of ±0.5 °C.

• Industry-leading long-term stability • True temperature-compensated digital I2C or SPI output

• Industry-leading reliability • Energy efficiency

• Lowest total cost solution • Ultra-small package size and options

• Other accuracies available: ±1.7 %RH (HIH9000 Series), ±2.0 %RH (HIH8000 Series), ±3.0 %RH (HIH7000 Series),

and ±4.0 %RH (HIH6100 Series)

What makes our sensors better?

• One sensor does the work of two!

• ±4.5 %RH accuracy (humidity performance)

• ±0.5 °C accuracy (temperature performance)

• -40 °C to 100 °C [-40 °F to 212 °F] operating

temperature range

The series consists of packaging variations, offering customers the abil-

ity to choose housing style (SIP 4-Pin or SOIC-8 SMD), filter (hydrophobic

filter or no filter), output (I2C or SPI), and packaging (tape and boxed, tape

and reel, or samples on tape).

sensing.honeywell.com

*Competitive Differentiator

±4.5

ACCURACY

%RH

Features

and Beneﬁts

INDUSTRY-LEADING LONG-TERM STABILITY*

(1.2 %RH OVER FIVE YEARS)

Competitive humidity sensors require a 12 hour at 75 %RH rehydration process

(which requires special equipment chambers) to correct reflow temperature offset.

Honeywell’s sensor also experiences an offset after reflow; however,

it only requires a five-hour rehydration under ambient conditions

(>50 %RH). Honeywell’s industry-leading long-term stability:

• Minimizes system performance issues.

• Helps support system uptime by eliminating the need

to service or replace the sensor during its application

life.

• Eliminates the need to regularly recalibrate the

sensor in the application, which can be inconvenient and

costly.

INDUSTRY-LEADING RELIABILITY

(MTTF 9,312,507 HR)*

Thermoset-polymer capacitive sensing element’s multilayer construction provides

resistance to most application hazards such as condensation, dust, dirt,

oils, and common environmental chemicals, which help provide industry-leading

reliability.

LOWEST TOTAL COST SOLUTION*

Honeywell’s HumidIcon HIH6000 Series delivers the lowest total cost solution due

to the sensor’s industry-leading combined humidity/temperature sensor.

COMBINED HUMIDITY AND TEMPERATURE SENSOR

Allows the RH measurement to be temperature compensated, and provides a

second, standalone temperature sensor output; allows the user to purchase one

sensor instead of two.

ENERGY EFFICIENT*

• Low supply voltage: Can operate down to 2.3 Vdc, which allows use in low

energy and wireless-compatible applications to enhance energy savings

and prolong system battery life.

• Low power consumption: The sensor goes into sleep mode when not

taking a measurement within the application, consuming only 1 µA of power

versus 650 µA in full operation in a battery operated system; sleep mode helps

maximize battery life, reduces power supply size, and reduces the application’s

overall weight.

Offers customers the lowest total cost solution.

One sensor does the work of two!

4sensing.honeywell.com

HIGH RESOLUTION

High 14-bit humidity sensor resolution and 14-bit temperature sensor resolution

within the application help the user’s system detect the smallest relative

humidity or temperature change.

TRUE, TEMPERATURE-COMPENSATED

DIGITAL I2C OR SPI OUTPUT*

Typically allows the customer to remove the components associated with signal

conditioning from the PCB to free up space and reduce costs associated with

those components (e.g., acquisition, inventory, assembly). True, temperature-

compensated digital I2C or SPI output often eliminates problems that could occur

from having multiple signal conditioning components across the PCB, as well as

simplifies integration to the microprocessor, eliminating the need for customer-

implemented, complex signal conditioning.

HOUSING STYLE

SOIC-8 SMD (Surface Mount Device) or SIP 4 Pin; ultra-small size allows for

flexibility of use within the application, occupies less space on the PCB, and

typically simplifies placement on crowded PCBs or in small devices; industry

standard design simplifies design-in.

FILTER

Available with hydrophobic filter and condensation-resistance, allowing for use in

many condensing environments, or without hydrophobic filter, non-condensing.

TAPE AND REEL

Allows for use in high volume, automated pick-and-place manufacturing,

eliminating lead misalignment to the PCB and helping the customer to reduce

manufacturing costs.

WIDE OPERATING TEMPERATURE RANGE

-40 °C to 100 °C [-40 °F to 212 °F] allows for use in many applications.

OPTIONAL ONE OR TWO %RH LEVEL ALARM OUTPUTS

Provides the ability to monitor whether the RH level has exceeded or fallen below

predetermined and critical levels within the application.

MULTI-FUNCTION ASIC

Delivers flexibility within the application by lowering or eliminating the risk and cost

of OEM calibration.

ROHS AND WEEE COMPLIANT, HALOGEN FREE

Free up PCB space. Reduce costs.

Choose options to best ﬁt the application.

Features

and Beneﬁts

*Competitive Differentiator

sensing.honeywell.com

INDUSTRIAL

HVAC/R

May be used to provide precise RH and temperature measurement in air

conditioning/air movement systems, enthalpy sensing, thermostats, humidifiers/

dehumidifiers, and humidistats to maintain occupant comfort and ideal storage

humidity/temperature while achieving low energy consumption, supporting system

accuracy and warranty requirements, maximizing system uptime, and improving

overall system quality.

AIR COMPRESSORS

May be used to provide precise RH measurement in compressed air lines, allowing

the system to remove any condensation; dry compressed air is critical for customer

process control measurement.

WEATHER STATIONS

May be used to provide precise RH and temperature measurement in ground-based

and airborne weather stations, allowing real time and highly accurate monitoring/

reporting of actual weather conditions.

TELECOM CABINETS

May be used to provide precise RH and temperature measurement in the telecom

cabinet HVAC system; maintaining proper temperature and humidity levels in the

cabinet provides maximum system uptime and performance.

INDUSTRIAL INCUBATORS/MICROENVIRONMENTS

May be used to provide optimal temperature and RH levels to support critical

processes and experiments, enhancing process efficiency with desired climate

conditions.

GRAIN DRYING SYSTEMS

May be used in cable-mounted grain drying management systems to measure

the moisture content and temperature level inside the grain silos to help the grains

remain dry.

MEDICAL

RESPIRATORY THERAPY

May be used to provide precise RH and temperature measurement in sleep

apnea machines and ventilators, enhancing patient comfort, safety and treatment

effectiveness with warm and humidified air.

INCUBATORS/MICROENVIRONMENTS

May be used to provide optimal temperature and RH levels to support critical

processes and experiments, enhancing process efficiency with desired climate

conditions.

Potential Applications

6sensing.honeywell.com

HIH6000 Series ±4.5 %RH Accuracy | ±0.5 °C Temperature Accuracy

Table 1. Environmental Specifications

Characteristic Condition Min. Typ. Max. Unit

Operating temperature range powered -40 [-40] –100 [212] °C [°F]

Operating humidity range powered 0 – 100 %RH

Storage temperature range unpowered -40 [-40] –125 [257] °C [°F]

Storage humidity range –30 –50 %RH

Soldering temperature:

manual

automated

4 s reflow peak

30 s reflow peak

–

350 [662]

260 [500]

°C [°F]

ESD MIL-STD 883H, Method 3015.7 – – ±4 kV

Latch-up immunity – – – ±100 mA

Shock

MIL-STD 202G, Method 213D, Test Condition C,

half-sine, 6 ms ±3 perpendicular axis, 3 shock pulses

per axis

– – 100 g

Vibration MIL-STD 202G, Method 204D, Test Condition D,

10 Hz to 2000 Hz – – 20 g

Light sensitivity exposed to 50 lumens yellow light; exhibited no change in output

Reliability (MTTF) 9,312,507 hr

Table 2. Humidity Performance Specifications

Characteristic Condition Min. Typ. Max. Unit

Supply voltage range VDD 2.3 3.3 5.5 Vdc

Compensated humidity range15 °C to 50 °C [41 °F to 122 °F] 20 – 80 %RH

Compensated temp. range1– 5 [41] – 50 [122] °C [°F]

Resolution 14 bit ADC resolution – – 0.04 %RH

Accuracy225 °C [77 °F] rising RH – ±4.5 – %RH

Response time airflow minimum 20 l/min – 6 8 s

Operating range non-condensing 0 – 100 %RH

Long term stability 50 %RH for 5 years – ±0.05 ±1.2 %RH

Impact of soldering IPC/EIA/JEDEC J-STD-020D, peak temp.

of 260 °C [500 °F] – – ±2.5 %RH

Notes:

1 Conversion Formulas:

14 bit ADC output for humidity to %RH: 14 bit ADC output for temperature conversion to °C:

Humidity (%RH) = Humidity_14_bit_ADC_output x 100

214 – 2 Temperature (C°) = Temperature_14_bit_ADC_output x 165 – 40

214 – 2

2Accuracy is specified at the typical supply voltage of 3.3 Vdc and at 25 °C [77 °F]. It is the maximum deviation from the ideal transfer function of

relative humidity measured over the compensated humidity range of 20 %RH to 80 %RH.

sensing.honeywell.com

Honeywell HumidIcon™ Digital Humidity/Temperature Sensors

Table 3. Temperature Performance Specifications

Characteristic Condition Min. Typ. Max. Unit

Supply voltage variation 2.3 Vdc to 5.5 Vdc –0.5 1.0 °C

Compensated temp. range – 5 [41] – 50 [122] °C [°F]

Resolution 14 bit ADC resolution – – 0.025 °C

Accuracy 5 °C to 50 °C [41 °F to 122 °F] – ±0.5 – °C

Response time 1/e slow moving air 5 – 30 s

Long term stability 25 °C for 5 years – – ±0.05 °C/yr

Impact of soldering IPC/EIA/JEDEC J-STD-020D, peak temp.

of 260 °C [500 °F] – – ±0.1 °C

Table 4. Current Consumption

Characteristic VDD Abbr. Condition Typ. Max. Unit

Sleep current 3.3 ISLEEP –0.6 1µA

Supply current:

I2C

SPI

3.3

IDD

14 bit fastest update, no sleep

0.65

0.75

Table 5. Input and Output Characteristics

Characteristic Abbr. Condition Min. Typ. Max. Unit

Supply voltage VDD – 2.3 3.3 5.5 Vdc

Low level output voltage VOL IOL = 2.8 mA min. – – 20 % VDD

High level output voltage VOH IOH = -2.8 mA min. 80 % – – VDD

Low level input voltage VIL – – – 20 % VDD

High level input voltage VIH – 80 % – – VDD

Pull-up resistor:

I2C

SPI (for SS only)

RSS

–

2.2

–

kOhm

Table 6. Measurement Timing

Characteristic Abbr. Condition Min. Typ. Max. Unit

Start-up time (power-on to

data ready) TSTA 14 bit TH and 14 bit humidity resolution – 50 60 ms

Update rate application dependent: measurements are taken only when the application requests them

8sensing.honeywell.com

HIH6000 Series ±4.5 %RH Accuracy | ±0.5 °C Temperature Accuracy

Figure 1. I2C Timing Diagram

SCL

LOW

HDSTA

HIGH

HDDAT

SUSTA

SUSTO

BUS

SUDAT

Characteristic Abbr. Min. Typ. Max. Unit

SCL clock frequency FSCL 100 –400 kHz

Start condition hold time relative to SCL edge tHDSTA 0.1 – – µs

Minimum SCL clock low width1 tLOW 0.6 – – µs

Minimum SCL clock high width1 tHIGH 0.6 – – µs

Start condition setup time relative to SCL edge tSUSTA 0.1 – – µs

Data hold time on SDA relative to SCL edge tHDDAT 0 – 0.5 µs

Data setup time on SDA relative to SCL edge tSUDAT 0.1 – – µs

Stop condition setup time on SCL tSUSTO 0.1 – – µs

Bus free time between stop and start condition tBUS 1 – – µs

Note:

1 Combined low and high widths must equal or exceed minimum SCL period.

Figure 2. SPI Timing Diagram

BUS

CLKD

SCLK

MISO

HIGH

SUSS

HiZHiZ

HDSS

LOW

CLKD

Characteristic Abbr. Min. Typ. Max. Unit

SCLK clock frequency fSCL 50 –800 kHz

SS drop to first clock edge tHDSS 2.5 – – μs

Minimum SCLK clock low width1tLOW 0.6 – – μs

Minimum SCLK clock high width1tHIGH 0.6 – – μs

Clock edge to data transition tCLKD 0 – 0.5 μs

Rise of SS relative to last clock edge tSUSS 0.1 – – μs

Bus free time between rise and fall of SS tBUS 2 – – µs

Note:

1 Combined low and high widths must equal or exceed minimum SCLK period.

sensing.honeywell.com

Honeywell HumidIcon™ Digital Humidity/Temperature Sensors

Figure 3. SOIC-8 SMD Typical Application Circuits

I2C SPI

Digital Humidity/Temp.

Sensor

CORE

SCL

SDA

AL_L

AL_H

SUPPLY

= 2.3 Vdc to 5.5 Vdc

GND

12 V

0.1 µF

0.22 µF

2.2

kOhm

LED

2.2

kOhm

Digital Humidity/Temp.

Sensor

CORE

SCLK

MISO

AL_L

0.1 µF

0.22 µF

kOhm

LED

SUPPLY

= 2.3 Vdc to 5.5 Vdc

Figure 4. SOIC-8 SMD Mounting Dimensions, PCB Landing Pattern and Pinout [For reference only: mm/[in].)

Mounting Landing Pattern

4,90

[0.193]

3,90

[0.1

53]

1,905

[0.075]

1,27

[0.050]

0.41

[0.016]

1234

8765

6,0

[0.236]

0,15

[0.006]

0,203

[0.0080]

2,055

[0.081]

8X 0,61

[0.024

]

8X 2,03

[0.08]

4X 4,9

[0.193

]

6X 1,27

[0.05]

Pinout for I2C Versions Pinout for SPI Versions

Pin ASIC Pad Description Pin ASIC Pad Description

1 VCORE connect via 0.1 µF to ground 1 VCORE connect via 0.1 µF to ground

2 VSS supply ground 2 VSS supply ground

3 SCL I2C clock 3 SS slave select (Input)

4 SDA I2C data 4 SCLK serial clock

51AL_H alarm output high 5 MISO master-in-slave-out

61AL_L alarm output low 61AL_L alarm output low

7 NC not connected externally 7 NC not connected externally

8 VDD supply voltage, connect via 0.22 µF to ground 8 VDD supply voltage, connect via 0.22 µF to ground

1 Do not connect Pin(s) 5 and/or 6 if the built-in alarm feature is not desired. 1 Do not connect Pin 6 if the built-in alarm feature is not desired.

Tape and Reel

4,00

[0.157]

1,50

[0.059]

1,75

[0.069] 0,29

[0.011 ]

[0.51]

330

[13,0]

17,4

[0.68]

102

[4.0]

8,00

[0.315]

12.00

[0.472]

5,50

[0.216]

2,58

[0.102]

10 sensing.honeywell.com

HIH6000 Series ±4.5 %RH Accuracy | ±0.5 °C Temperature Accuracy

Figure 5. SIP 4 Pin Typical Application Circuit

Digital Humidity/Temp.

Sensor

SCL

SDA

SUPPLY

= 2.3 Vdc to 5.5 Vdc

GND

0.22 µF

2.2

kOhm

2.2

kOhm

Figure 6. SIP 4 Pin Mounting Dimensions, PCB Landing Pattern and Pinout [For reference only: mm/[in].)

Mounting Landing Pattern

1234

8,9

[0.35]

1,20

[0.047]

PCB

1,2 - 2,0

[0.05 - 0.08]

4,90

[0.193]

3,90

[0.1

53]

5,0

[0.1

97]

1,27

[0.050]

0.41

[0.016]

0,063

[0.0025]

0,203

[0.0080]

1,905

[0.075]

1,27

[0.050]

1,05 DIA.

[0.040] 0,65 DIA.

[0.025]

Tape and Reel1

4,00

[0.157]

1,50

[0.059]

1,75

[0.069] 0,32

[0.013]

[0.51]

330

[13,0]

21,4

[0.84]

102

[4.0]

8,00

[0.315]

16,00

[0.630]

5,00

[0.197]

2,61

[0.103]

1 For orders of 250 to 1000 units

Pin ASIC Pad Description

1 VDD connect via 0.22 µF to ground

2 VSS supply ground

3 SCL I2C clock

4 SDA I2C data

sensing.honeywell.com

Honeywell HumidIcon™ Digital Humidity/Temperature Sensors

Order Guide

Catalog Listing Description

HIH6020-021-0011Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy, SIP

4 Pin, without filter, non-condensing, 100 units on tape

HIH6020-021-001S Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy, SIP

4 Pin, without filter, non-condensing, five units on tape (sample)

HIH6021-021-0011Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy, SIP

4 Pin, with filter, condensation-resistant, 100 units on tape

HIH6021-021-001S Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy, SIP

4 Pin, with filter, condensation-resistant, five units on tape (sample)

HIH6030-000-001 Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, SPI, ±4.5 %RH accuracy,

SOIC-8 SMD, without filter, non-condensing, 1000 units on tape and reel

HIH6030-000-001S Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, SPI, ±4.5 %RH accuracy

SOIC-8 SMD, without filter, non-condensing, five units on tape (sample)

HIH6030-021-001 Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy,

SOIC-8 SMD, without filter, non-condensing, 1000 units on tape and reel

HIH6030-021-001S Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy,

SOIC-8 SMD, without filter, non-condensing, five units on tape (sample)

HIH6031-000-001 Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, SPI, ±4.5 %RH accuracy,

SOIC-8 SMD, with filter, condensation-resistant, 1000 units on tape and reel

HIH6031-000-001S Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, SPI, ±4.5 %RH accuracy,

SOIC-8 SMD, with filter, condensation-resistant, five units on tape (sample)

HIH6031-021-001 Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy,

SOIC-8 SMD, with filter, condensation-resistant, 1000 units on tape and reel

HIH6031-021-001S Honeywell HumidIcon™ Digital Humidity/Temperature Sensors: HIH6000 Series, I2C, ±4.5 %RH accuracy,

SOIC-8 SMD, with filter, condensation-resistant, five units on tape (sample)

1 Orders of 250 units or more are packaged on tape and reel.

12 sensing.honeywell.com

NOTICE:

SENSOR REHYDRATION

• Exposure to elevated temperatures, such as those

experienced during solder reflow, may dry out the sensing

element. It is recommended that the sensor be allowed time

to rehydrate after soldering or other high temperature/dry

exposures.

• Exposure to these conditions will not permanently damage the

sensor. It will generally return to its factory-calibrated value after

rehydration.

• If rehydration is not performed, the sensor may read a slight

offset that slowly disappears over time as the sensor becomes

exposed to ambient conditions. Conversely, extended

exposure to condensing and high humidity environments

(>90 %RH) may cause a revisable shift in readings which will

generally return to normal after the sensor has been allowed to

dry off.

To rehydrate the sensor, expose it to room temperature under

ambient conditions (>50 %RH) for a minimum of five hours.

HIH6000 Series • ±4.5 %RH Accuracy

WARNING

PERSONAL INJURY

DO NOT USE these products as safety or emergency stop

devices or in any other application where failure of the

product could result in personal injury.

Failure to comply with these instructions could result in

death or serious injury.

WARNING

MISUSE OF DOCUMENTATION

• The information presented in this product sheet is for

reference only. Do not use this document as a product

installation guide.

• Complete installation, operation, and maintenance

information is provided in the instructions supplied with

each product.

Failure to comply with these instructions could result in

death or serious injury.

009073-7-EN

May 2015

Sensing and Control

Honeywell

1985 Douglas Drive North

Golden Valley, MN 55422

honeywell.com

Find out more

Honeywell serves its customers

through a worldwide network

of sales offices, representatives

and distributors. For application

assistance, current specifications,

pricing or name of the nearest

Authorized Distributor, contact

your local sales office.

To learn more about Honeywell’s

sensing and control products,

call +1-815-235-6847 or

1-800-537-6945, visit

sensing.honeywell.com,

or e-mail inquiries to

info.sc@honeywell.com

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as being free of

defective materials and faulty workmanship. Honeywell’s standard

product warranty applies unless agreed to otherwise by Honeywell

in writing; please refer to your order acknowledgement or consult

your local sales office for specific warranty details. If warranted

goods are returned to Honeywell during the period of coverage,

Honeywell will repair or replace, at its option, without charge those

items it finds defective. The foregoing is buyer’s sole remedy

and is in lieu of all other warranties, expressed or implied,

including those of merchantability and fitness for a particu-

lar purpose. In no event shall Honeywell be liable for conse-

quential, special, or indirect damages.

While we provide application assistance personally, through our

literature and the Honeywell website, it is up to the customer to

determine the suitability of the product in the application.

Specifications may change without notice. The information we

supply is believed to be accurate and reliable as of this printing.

However, we assume no responsibility for its use.

ADDITIONAL INFORMATION

The following associated literature is available on the Web:

• Product installation instructions

• Product application note

• Application sheets:

– Humidity Sensor Performance Characteristics

– Humidity Sensor Theory and Behavior

– Humidity Sensor Moisture and Psychrometrics

– Humidity Sensor Chemical Resistivity

– Thermoset Polymer-Based Capacitive Sensors

• Technical Notes:

– I2C Communication with the Honeywell HumidIcon™ Digital

Humidity/Temperature Sensors

– SPI Communication with the Honeywell HumidIcon™ Digital

Humidity/Temperature Sensors

– Using Alarms on the Honeywell HumidIcon™ Digital

Humidity/Temperature Sensors

– Entering and Using Command Mode on the Honeywell

HumidIcon™ Digital Humidity/Temperature Sensors