NCV4276, NCV4276A 400 mA Low-Drop Voltage Regulator The NCV4276 is a 400 mA output current integrated low dropout regulator family designed for use in harsh automotive environments. It includes wide operating temperature and input voltage ranges. The device is offered with fixed output voltage options of 1.8 V, 2.5 V, and 3.3 V with 4% output voltage accuracy while the 5.0 V and adjustable voltage versions are available either in 2% or 4% output voltage accuracy. It has a high peak input voltage tolerance and reverse input voltage protection. It also provides overcurrent protection, overtemperature protection and inhibit for control of the state of the output voltage. The NCV4276 family is available in DPAK and D2PAK surface mount packages. The output is stable over a wide output capacitance and ESR range. Features http://onsemi.com MARKING DIAGRAMS 1 76AXXG ALYWW 5 DPAK 5-PIN DT SUFFIX CASE 175AA 1 4276XG ALYWW 1 NCV4276A NCV4276 * 3.3 V, 2.5 V, 1.8 V 4% Output Voltage * 5.0 V and Adjustable Voltage Version (from 2.5 V to 20 V) 4% or * * * * * * * 2% Output Voltage 400 mA Output Current 500 mV (max) Dropout Voltage (5.0 V Output) Inhibit Input Very Low Current Consumption Fault Protection +45 V Peak Transient Voltage -42 V Reverse Voltage Short Circuit Thermal Overload NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes Pb-Free Packages are Available 1 NC V4276A-XX AWLYWWG 5 D2PAK 5-PIN DS SUFFIX CASE 936A 1 NC V4276-XX AWLYWWG 1 NCV4276A NCV4276 Pin 1. I 2. INH Tab, 3. GND* 4. VA 5. Q Pin 1. I 2. INH Tab, 3. GND* 4. NC 5. Q * Tab is connected to Pin 3 on all packages. A WL, L Y WW G x, xx = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Device = Voltage Ratings as indicated below A-Version DPAK XX = AJ (Adj. Voltage) D2PAK XX = AJ (Adj. Voltage) Non-A-Version DPAK X = V (Adj. Voltage) X = 5 (5.0 V) X = 3 (3.3 V) D2PAK XX = AJ (Adj. Voltage) XX = 50 (5.0 V) XX = 33 (3.3 V) XX = 25 (2.5 V) XX = 18 (1.8 V) ORDERING INFORMATION See detailed ordering and shipping information in the ordering information section on page 17 of this data sheet. (c) Semiconductor Components Industries, LLC, 2006 May, 2006 - Rev. 16 1 Publication Order Number: NCV4276/D NCV4276, NCV4276A I Q Bandgap Reference Error Amplifier Current Limit and Saturation Sense - + Thermal Shutdown INH GND NC Figure 1. 4276 Block Diagram I Q Bandgap Reference Error Amplifier Current Limit and Saturation Sense - + Thermal Shutdown INH GND VA Figure 2. 4276 Adjustable Block Diagram http://onsemi.com 2 NCV4276, NCV4276A PIN FUNCTION DESCRIPTION Pin No. Symbol Description 1 I 2 INH Inhibit; Set low-to inhibit. 3 GND Ground; Pin 3 internally connected to heatsink. 4 NC / VA 5 Q Input; Battery Supply Input Voltage. Not connected for fixed voltage version / Voltage Adjust Input for adjustable voltage version; use an external voltage divider to set the output voltage Use 22 mF, ESR < 2.5 W at 10 kHz to ground with the 5.0 V and adjustable regulators. See Figures 3, 4, and 5. Use 10 mF, ESR < 1.8 W at 10 kHz to ground with the 3.3 V, 2.5 V, and 1.8 V regulators. See Figures 3 and 6. MAXIMUM RATINGS* Symbol Min Max Unit Input Voltage Rating VI -42 45 V Input Peak Transient Voltage VI - 45 V VINH -42 45 V Output Voltage VQ -1.0 40 V Ground Current Iq - 100 mA Input Voltage Operating Range VI VQ + 0.5 V or 4.5 V (Note 1) 40 V - - - 4.5 250 1.25 - - - kV V kV Junction Temperature TJ -40 150 C Storage Temperature Tstg -50 150 C Inhibit INH Voltage ESD Susceptibility (Human Body Model) (Machine Model) (Charged Device Model) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. *During the voltage range which exceeds the maximum tested voltage of I, operation is assured, but not specified. Wider limits may apply. Thermal dissipation must be observed closely. LEAD TEMPERATURE SOLDERING REFLOW (Note 2) Lead Temperature Soldering Reflow (SMD styles only), Leaded, 60-150 s above 183, 30 s max at peak Reflow (SMD styles only), Lead Free, 60-150 s above 217, 40 s max at peak Wave Solder (through hole styles only), 12 sec max TSLD - - - 240 265 310 C THERMAL CHARACTERISTICS Characteristic Test Conditions (Typical Value) Unit DPAK 5-PIN PACKAGE Min Pad Board (Note 3) 1, Pad Board (Note 4) Junction-to-Tab (psi-JLx, yJLx) 4.2 4.7 C/W Junction-to-Ambient (RqJA, qJA) 100.9 46.8 C/W 0.4 sq. in. Spreader Board (Note 5) 1.2 sq. in. Spreader Board (Note 6) Junction-to-Tab (psi-JLx, yJLx) 3.8 4.0 C/W Junction-to-Ambient (RqJA, qJA) 74.8 41.6 C/W D2PAK 1. 2. 3. 4. 5. 6. 5-PIN PACKAGE Minimum VI = 4.5 V or (VQ + 0.5 V), whichever is higher. Per IPC / JEDEC J-STD-020C. 1 oz. copper, 0.26 inch2 (168 mm2) copper area, 0.062 thick FR4. 1 oz. copper, 1.14 inch2 (736 mm2) copper area, 0.062 thick FR4. 1 oz. copper, 0.373 inch2 (241 mm2) copper area, 0.062 thick FR4. 1 oz. copper, 1.222 inch2 (788 mm2) copper area, 0.062 thick FR4. http://onsemi.com 3 NCV4276, NCV4276A ELECTRICAL CHARACTERISTICS (VI = 13.5 V; -40C < TJ < 150C; unless otherwise noted.) NCV4276 Characteristic Symbol Test Conditions NCV4276A Min Typ Max Min Typ Max Unit Output Output Voltage, 5.0 V Version VQ 5.0 mA < IQ < 400 mA, 6.0 V < VI < 28 V 4.8 5.0 5.2 4.9 5.0 5.1 V Output Voltage, 5.0 V Version VQ 5.0 mA < IQ < 200 mA, 6.0 V < VI < 40 V 4.8 5.0 5.2 4.9 5.0 5.1 V Output Voltage, 3.3 V Version VQ 5.0 mA < IQ < 400 mA, 4.5 V < VI < 28 V 3.168 3.3 3.432 - - - V Output Voltage, 3.3 V Version VQ 5.0 mA < IQ < 200 mA, 4.5 V < VI < 40 V 3.168 3.3 3.432 - - - V Output Voltage, 2.5 V Version VQ 5.0 mA < IQ < 400 mA, 4.5 V < VI < 28 V 2.4 2.5 2.6 - - - V Output Voltage, 2.5 V Version VQ 5.0 mA < IQ < 200 mA, 4.5 V < VI < 40 V 2.4 2.5 2.6 - - - V Output Voltage, 1.8 V Version VQ 5.0 mA < IQ < 400 mA, 4.5 V < VI < 28 V 1.728 1.8 1.872 - - - V Output Voltage, 1.8 V Version VQ 5.0 mA < IQ < 200 mA, 4.5 V < VI < 40 V 1.728 1.8 1.872 - - - V AVQ 5.0 mA < IQ < 400 mA VQ+1 < VI < 40 V VI > 4.5 V -4% - +4% -2% - +2% V 400 700 1100 400 700 1100 mA mA Output Voltage, Adjustable Version Output Current Limitation IQ VQ = 90% VQTYP (VQTYP = 2.5 V for ADJ version) Quiescent Current (Sleep Mode) Iq = II - IQ Iq VINH = 0 V - - 10 - - 10 Quiescent Current, Iq = II - IQ Iq IQ = 1.0 mA - 130 220 - 130 200 mA Quiescent Current, Iq = II - IQ Iq IQ = 250 mA - 10 15 - 10 15 mA Quiescent Current, Iq = II - IQ Iq IQ = 400 mA - 25 35 - 25 35 mA IQ = 250 mA, VDR = VI - VQ VI = 5.5 V VI = 4.5 V VI = 4.5 V VI = 4.5 V VI > 4.5 V - - - - - 250 - - - 250 500 1.332 2.1 2.772 500 - - - - - - - - - 250 - - - - 500 mV V V V mV IQ = 250 mA - - - - 250 500 mV IQ = 5.0 mA to 400 mA - 10 35 - 3.0 20 mV DVI = 12 V to 32 V, IQ = 5.0 mA - 2.5 25 - 4.0 15 mV fr = 100 Hz, Vr = 0.5 Vpp - 60 - - 54 - dB - 0.5 - - 0.5 - mV/K Dropout Voltage, VDR 5.0 V Version 3.3 V Version 2.5 V Version 1.8 V Version Adjustable Version Dropout Voltage (5.0 V Version) VDR Load Regulation DVQ,LO Line Regulation DVQ Power Supply Ripple Rejection PSRR Temperature Output Voltage Drift dVQ/dT - Inhibit Inhibit Voltage, Output High VINH VQ w VQMIN - 2.8 3.5 - 2.3 3.5 V Inhibit Voltage, Output Low (Off) VINH VQ v 0.1 V 0.5 1.7 - 0.5 2.2 - V Input Current IINH VINH = 5.0 V 5.0 10 20 5.0 10 20 mA Min Typ Max Min Typ Max Unit 150 - 210 150 - 210 C THERMAL SHUTDOWN Characteristic Symbol Thermal Shutdown Temperature* TSD Test Conditions IQ = 5.0 mA *Guaranteed by design, not tested in production. http://onsemi.com 4 NCV4276, NCV4276A II 5.5 - 45 V Input I 1 CI1 100 mF CI2 100 nF CQ 22 mF NCV4276 INH 2 4 3 IINH Output IQ 5 Q NC RL GND Figure 3. Applications Circuit; Fixed Voltage Version VQ = [(R1 + R2) * Vref] / R2 II Input I 1 CI1 100 mF CI2 100 nF CQ 22 mF NCV4276 NCV4276A INH 2 4 3 IINH Output IQ 5 Q R1 VA RL GND R2 Figure 4. Applications Circuit; Adjustable Voltage Version TYPICAL PERFORMANCE CHARACTERISTICS 10.0 1000 9.0 Unstable ESR Region for CQ = 1 mF - 22 mF 100 CQ = 10 mF for these Output Voltages 8.0 ESR (W) ESR (W) 7.0 10 1 0 50 100 150 2.5 V 4.0 1.8 V 2.0 1.0 Stable ESR Region 0.01 Unstable Region 5.0 3.0 Maximum ESR for CQ = 1 mF - 22 mF 0.1 3.3 V 6.0 200 250 300 350 OUTPUT CURRENT (mA) 400 0.0 450 Figure 5. Output Stability with Output Capacitor ESR, 5.0 V and Adjustable Regulator Stable Region 0 50 100 150 200 250 300 350 OUTPUT CURRENT (mA) 400 450 Figure 6. Output Stability with Output Capacitor ESR, 1.8 V, 2.5 V, 3.3 V Regulators http://onsemi.com 5 NCV4276, NCV4276A TYPICAL PERFORMANCE CHARACTERISTICS - 4276 Version 5.2 45 40 VI = 13.5 V, RL = 1000 W TJ = 25C RL = 20 W 35 5.1 Iq, (mA) VQ, (V) 30 5.0 25 20 15 4.9 10 5 4.8 -40 0 40 80 120 0 160 0 10 20 TJ (C) 6 50 6 TJ = 25C RL = 20 W 5 TJ = 25C RL = 6.8 kW 4 2 II, (mA) 4 VQ, (V) 40 Figure 8. Current Consumption Iq versus Input Voltage VI, 5.0 V Regulator Figure 7. Output Voltage VQ versus Temperature TJ, 5.0 V Regulator 3 2 0 -2 -4 1 0 30 VI (V) -6 0 2 4 6 8 -8 -50 10 -25 0 25 50 VI (V) VI (V) Figure 9. Low Voltage Behavior, 5.0 V Regulator Figure 10. High Voltage Behavior, 5.0 V Regulator http://onsemi.com 6 NCV4276, NCV4276A TYPICAL PERFORMANCE CHARACTERISTICS - 4276 Version 600 800 TJ = 25C VQ = 0 V 700 500 500 TJ = 125C IQ, (mA) VDR, (mV) 600 400 300 TJ = 25C 200 400 300 200 100 0 100 0 50 100 150 200 250 300 350 0 400 0 10 20 30 40 IQ (mA) VI (V) Figure 11. Voltage Drop VDR versus Output Current IQ, 5.0 V Regulator Figure 12. Maximum Output Current IQ versus Input Voltage VI, 5.0 V Regulator 60 50 1.6 TJ = 25C VI = 13.5 V 50 TJ = 25C VI = 13.5 V 1.4 1.2 1.0 Iq, (mA) Iq, (mA) 40 30 20 0.8 0.6 0.4 10 0 0.2 0 100 200 300 400 500 600 0 0 IQ (mA) 10 20 30 40 50 IQ (mA) Figure 14. Current Consumption Iq versus Output Current IQ (Low Load), 5.0 V Regulator Figure 13. Current Consumption Iq versus Output Current IQ (High Load), 5.0 V Regulator http://onsemi.com 7 60 NCV4276, NCV4276A TYPICAL PERFORMANCE CHARACTERISTICS - 4276A Version 6.0 VI = 13.5 V RL = 1 kW VQ, OUTPUT VOLTAGE (V) VQ, OUTPUT VOLTAGE (V) 5.2 5.1 5.0 4.9 4.8 -40 0 40 80 120 5.0 3.0 2.0 1.0 0 160 6.0 8.0 Figure 16. Low Voltage Behavior, 5.0 V Regulator 10 60 Iq, CURRENT CONSUMPTION (mA) IQ, OUTPUT CURRENT (mA) 4.0 Figure 15. Output Voltage vs. Junction Temperature, 5.0 V Regulator 600 400 200 0 10 20 30 40 50 50 VI = 13.5 V TJ = 25C 40 30 20 10 0 0 100 200 300 400 500 VI, INPUT VOLTAGE (V) IQ, OUTPUT CURRENT (mA) Figure 17. Output Current vs. Input Voltage, 5.0 V Regulator Figure 18. Current Consumption vs. Output Current (High Load), 5.0 V Regulator 1.6 600 600 1.4 1.2 VDR, DROP VOLTAGE (mV) Iq, CURRENT CONSUMPTION (mA) 2.0 VI, INPUT VOLTAGE (V) TJ = 25C VQ = 0 V VI = 13.5 V 1.0 0.8 0.6 0.4 0.2 0 0 TJ, JUNCTION TEMPERATURE (C) 800 0 RL = 20 W TJ = 25C 4.0 0 10 20 30 40 50 500 TJ = 125C 400 300 TJ = 25C 200 100 0 60 0 100 200 300 IQ, OUTPUT CURRENT (mA) IQ, OUTPUT CURRENT (mA) Figure 19. Current Consumption vs. Output Current (Low Load), 5.0 V Regulator Figure 20. Drop Voltage vs. Output Current, 5.0 V Regulator http://onsemi.com 8 400 NCV4276, NCV4276A TYPICAL PERFORMANCE CHARACTERISTICS - 4276A Version 6.0 TJ = 25C RL = 20 W 4.0 2.0 30 II (mA) Iq, CURRENT CONSUMPTION (mA) 40 20 0 -2.0 RL = 6.8 kW TJ = 25C -4.0 -6.0 10 -8.0 0 0 10 20 30 40 -10 -50 50 -25 0 25 50 VI, INPUT VOLTAGE (V) VI, INPUT VOLTAGE (V) Figure 21. Current Consumption vs. Input Voltage, 5.0 V Regulator Figure 22. High Voltage Behavior, 5.0 V Regulator TYPICAL PERFORMANCE CHARACTERISTICS - Adjustable Version 4 2.55 2.54 VI = 13.5 V, RL = 1 kW 2.53 3 2.52 2.51 VQ (V) VQ (V) TJ = 25C RL = 20 W 3.5 2.50 2.49 2.5 2 1.5 2.48 1 2.47 0.5 2.46 2.45 -40 0 40 80 120 0 160 0 2 4 TJ (C) 8 10 Figure 24. Low Voltage Behavior, Adjustable Version Figure 23. Output Voltage vs. Temperature, Adjustable Version 800 60 700 TJ = 25C VI = 13.5 V 50 600 40 500 IQ (mA) IQ (mA) 6 VI (V) TJ = 25C VQ = 0 V 400 300 30 20 200 10 100 0 0 0 10 20 30 40 50 0 100 200 300 400 500 VI (V) IQ (mA) Figure 25. Maximum Output Current vs. Input Voltage, Adjustable Version Figure 26. Current Consumption vs. Output Current (High Load), Adjustable Version http://onsemi.com 9 600 NCV4276, NCV4276A TYPICAL PERFORMANCE CHARACTERISTICS - Adjustable Version 600 1.6 TJ = 25C VI = 13.5 V 1.4 500 1.0 VDR (mV) Iq (mA) 1.2 0.8 0.6 TJ = 125C 400 300 TJ = 25C 200 0.4 100 0.2 0 0 10 20 30 40 50 0 60 0 50 100 IQ (mA) 4.5 300 350 400 0 -2 3.5 -4 3.0 -6 II (mA) Iq (mA) 250 2 TJ = 25C RL = 20 W 4.0 200 IQ (mA) Figure 28. Voltage Drop vs. Output Current, Regulator set at 5.0 V, Adjustable Version Figure 27. Current Consumption vs. Output Current (Low Load), Adjustable Version 5.0 150 2.5 2.0 -8 -10 1.5 -12 1.0 -14 0.5 0 -16 -18 -50 0 10 20 30 40 50 TJ = 25C RL = 6.8 kW -25 0 25 VI (V) VI (V) Figure 29. Current Consumption vs. Input Voltage, Adjustable Version Figure 30. High Voltage Behavior, Adjustable Version http://onsemi.com 10 50 NCV4276, NCV4276A Circuit Description The NCV4276 is an integrated low dropout regulator that provides a regulated voltage at 400 mA to the output. It is enabled with an input to the inhibit pin. The regulator voltage is provided by a PNP pass transistor controlled by an error amplifier with a bandgap reference, which gives it the lowest possible dropout voltage. The output current capability is 400 mA, and the base drive quiescent current is controlled to prevent oversaturation when the input voltage is low or when the output is overloaded. The regulator is protected by both current limit and thermal shutdown. Thermal shutdown occurs above 150C to protect the IC during overloads and extreme ambient temperatures. will vary considerably. The capacitor manufacturer's data sheet usually provides this information. The value for the output capacitor CQ, shown in Figure 3, should work for most applications; however, it is not necessarily the optimized solution. Stability is guaranteed for CQ w 22 mF and an ESR v 2.5 W for the 5.0 V and Adjustable regulator and CQ w 10 mF and an ESR v 1.8 W for the 1.8 V, 2.5 V, and 3.3 V regulators. See Figures 5 and 6 for output stability at various load and capacitive ESR conditions. Inhibit Input The inhibit pin is used to turn the regulator on or off. By holding the pin down to a voltage less than 0.5 V, the output of the regulator will be turned off. When the voltage on the Inhibit pin is greater than 3.5 V, the output of the regulator will be enabled to power its output to the regulated output voltage. The inhibit pin may be connected directly to the input pin to give constant enable to the output regulator. Regulator The error amplifier compares the reference voltage to a sample of the output voltage (VQ) and drives the base of a PNP series pass transistor via a buffer. The reference is a bandgap design to give it a temperature-stable output. Saturation control of the PNP is a function of the load current and input voltage. Oversaturation of the output power device is prevented, and quiescent current in the ground pin is minimized. See Figure 5, Test Circuit, for circuit element nomenclature illustration. Setting the Output Voltage (Adjustable Version) The output voltage range of the adjustable version can be set between 2.5 V and 20 V (Figure ). This is accomplished with an external resistor divider feeding back the voltage to the IC back to the error amplifier by the voltage adjust pin VA. The internal reference voltage is set to a temperature stable reference of 2.5 V. The output voltage is calculated from the following formula. Ignoring the bias current into the VA pin: Regulator Stability Considerations The input capacitors (CI1 and CI2) are necessary to stabilize the input impedance to avoid voltage line influences. Using a resistor of approximately 1.0 W in series with CI2 can stop potential oscillations caused by stray inductance and capacitance. The output capacitor helps determine three main characteristics of a linear regulator: startup delay, load transient response and loop stability. The capacitor value and type should be based on cost, availability, size and temperature constraints. A tantalum or aluminum electrolytic capacitor is best, since a film or ceramic capacitor with its almost zero ESR can cause instability. The aluminum electrolytic capacitor is the least expensive solution, but, if the circuit operates at low temperatures (-25C to -40C), both the value and ESR of the capacitor VQ + [(R1 ) R2) * Vref]R2 Use R2 < 50 k to avoid significant voltage output errors due to VA bias current. Connecting VA directly to Q without R1 and R2 creates an output voltage of 2.5 V. Designers should consider the tolerance of R1 and R2 during the design phase. The input voltage range for operation (pin 1) of the adjustable version is between (VQ + 0.5 V) and 40 V. Internal bias requirements dictate a minimum input voltage of 4.5 V. The dropout voltage for output voltages less than 4.0 V is (4.5 V - VQ). http://onsemi.com 11 NCV4276, NCV4276A Calculating Power Dissipation in a Single Output Linear Regulator The maximum power dissipation for a single output regulator (Figure 31) is: PD(max) + [VI(max) * VQ(min)] IQ(max) Heatsinks A heatsink effectively increases the surface area of the package to improve the flow of heat away from the IC and into the surrounding air. Each material in the heat flow path between the IC and the outside environment will have a thermal resistance. Like series electrical resistances, these resistances are summed to determine the value of RqJA: (1) ) VI(max)Iq where RqJA + RqJC ) RqCS ) RqSA VI(max) VQ(min) IQ(max) is the maximum input voltage, is the minimum output voltage, is the maximum output current for the application, Iq is the quiescent current the regulator consumes at IQ(max). Once the value of PD(max) is known, the maximum permissible value of RqJA can be calculated: T RqJA + 150C * A PD where RqJC is the junction-to-case thermal resistance, RqCS is the case-to-heatsink thermal resistance, RqSA is the heatsink-to-ambient thermal resistance. RqJC appears in the package section of the data sheet. Like RqJA, it too is a function of package type. RqCS and RqSA are functions of the package type, heatsink and the interface between them. These values appear in data sheets of heatsink manufacturers. Thermal, mounting, and heatsinking considerations are discussed in the ON Semiconductor application note AN1040/D. (2) The value of RqJA can then be compared with those in the package section of the data sheet. Those packages with RqJA less than the calculated value in Equation 2 will keep the die temperature below 150C. In some cases, none of the packages will be sufficient to dissipate the heat generated by the IC, and an external heatsink will be required. IQ II VI SMART REGULATOR(R) (3) VQ } Control Features Iq Figure 31. Single Output Regulator with Key Performance Parameters Labeled http://onsemi.com 12 NCV4276, NCV4276A Thermal Model A discussion of thermal modeling is in the ON Semiconductor web site: http://www.onsemi.com/pub/collateral/BR1487-D.PDF. Table 1. DPAK 5-Lead Thermal RC Network Models Drain Copper Area (1 oz thick) 168 mm2 (SPICE Deck Format) 736 mm2 168 mm2 Cauer Network 168 mm2 736 mm2 Foster Network 736 mm2 Units Tau Tau Units C_C1 Junction GND 1.00E-06 1.00E-06 W-s/C 1.36E-08 1.361E-08 sec C_C2 node1 GND 1.00E-05 1.00E-05 W-s/C 7.41E-07 7.411E-07 sec C_C3 node2 GND 6.00E-05 6.00E-05 W-s/C 1.04E-05 1.029E-05 sec C_C4 node3 GND 1.00E-04 1.00E-04 W-s/C 3.91E-05 3.737E-05 sec C_C5 node4 GND 4.36E-04 3.64E-04 W-s/C 1.80E-03 1.376E-03 sec C_C6 node5 GND 6.77E-02 1.92E-02 W-s/C 3.77E-01 2.851E-02 sec C_C7 node6 GND 1.51E-01 1.27E-01 W-s/C 3.79E+00 9.475E-01 sec C_C8 node7 GND 4.80E-01 1.018 W-s/C 2.65E+01 1.173E+01 sec C_C9 node8 GND 3.740 2.955 W-s/C 8.71E+01 8.59E+01 sec C_C10 node9 GND 10.322 0.438 W-s/C 168 mm2 736 mm2 sec R's R's R_R1 Junction node1 0.015 0.015 C/W 0.0123 0.0123 C/W R_R2 node1 node2 0.08 0.08 C/W 0.0585 0.0585 C/W R_R3 node2 node3 0.4 0.4 C/W 0.0304 0.0287 C/W R_R4 node3 node4 0.2 0.2 C/W 0.3997 0.3772 C/W R_R5 node4 node5 2.97519 2.6171 C/W 3.115 2.68 C/W R_R6 node5 node6 8.2971 1.6778 C/W 3.571 1.38 C/W R_R7 node6 node7 25.9805 7.4246 C/W 12.851 5.92 C/W R_R8 node7 node8 46.5192 14.9320 C/W 35.471 7.39 C/W R_R9 node8 node9 17.7808 19.2560 C/W 46.741 28.94 C/W R_R10 node9 GND 0.1 0.1758 C/W NOTE: C/W Bold face items represent the package without the external thermal system. R1 Junction C1 R2 C2 R3 C3 Rn Cn Time constants are not simple RC products. Amplitudes of mathematical solution are not the resistance values. Ambient (thermal ground) Figure 32. Grounded Capacitor Thermal Network ("Cauer" Ladder) Junction R1 C1 R2 C2 R3 C3 Rn Cn Each rung is exactly characterized by its RC-product time constant; amplitudes are the resistances. Ambient (thermal ground) Figure 33. Non-Grounded Capacitor Thermal Ladder ("Foster" Ladder) http://onsemi.com 13 NCV4276, NCV4276A Table 2. D2PAK 5-Lead Thermal RC Network Models Drain Copper Area (1 oz thick) 241 mm2 (SPICE Deck Format) 788 mm2 241 mm2 Cauer Network 788 mm2 Foster Network 241 mm2 653 mm2 Units Tau Tau Units C_C1 Junction GND 1.00E-06 1.00E-06 W-s/C 1.361E-08 1.361E-08 sec C_C2 node1 GND 1.00E-05 1.00E-05 W-s/C 7.411E-07 7.411E-07 sec C_C3 node2 GND 6.00E-05 6.00E-05 W-s/C 1.005E-05 1.007E-05 sec C_C4 node3 GND 1.00E-04 1.00E-04 W-s/C 3.460E-05 3.480E-05 sec C_C5 node4 GND 2.82E-04 2.87E-04 W-s/C 7.868E-04 8.107E-04 sec C_C6 node5 GND 5.58E-03 5.95E-03 W-s/C 7.431E-03 7.830E-03 sec C_C7 node6 GND 4.25E-01 4.61E-01 W-s/C 2.786E+00 2.012E+00 sec C_C8 node7 GND 9.22E-01 2.05 W-s/C 2.014E+01 2.601E+01 sec C_C9 node8 GND 1.73 4.88 W-s/C 1.134E+02 1.218E+02 sec C_C10 node9 GND 7.12 1.31 W-s/C 241 mm2 653 mm2 sec R's R's R_R1 Junction node1 0.015 0.0150 C/W 0.0123 0.0123 C/W R_R2 node1 node2 0.08 0.0800 C/W 0.0585 0.0585 C/W R_R3 node2 node3 0.4 0.4000 C/W 0.0257 0.0260 C/W R_R4 node3 node4 0.2 0.2000 C/W 0.3413 0.3438 C/W R_R5 node4 node5 1.85638 1.8839 C/W 1.77 1.81 C/W R_R6 node5 node6 1.23672 1.2272 C/W 1.54 1.52 C/W R_R7 node6 node7 9.81541 5.3383 C/W 4.13 3.46 C/W R_R8 node7 node8 33.1868 18.9591 C/W 6.27 5.03 C/W R_R9 node8 node9 27.0263 13.3369 C/W 60.80 29.30 C/W node9 GND 1.13944 0.1191 C/W R_R10 NOTE: C/W Bold face items represent the package without the external thermal system. The Cauer networks generally have physical significance and may be divided between nodes to separate thermal behavior due to one portion of the network from another. The Foster networks, though when sorted by time constant (as above) bear a rough correlation with the Cauer networks, are really only convenient mathematical models. Cauer networks can be easily implemented using circuit simulating tools, whereas Foster networks may be more easily implemented using mathematical tools (for instance, in a spreadsheet program), according to the following formula: n R(t) + S Ri 1-e-ttaui i+1 http://onsemi.com 14 110 110 100 100 90 90 80 80 70 qJA (C/W) qJA (C/W) NCV4276, NCV4276A 1 oz 60 2 oz 70 60 1 oz 2 oz 50 50 40 40 30 150 200 250 300 350 400 450 500 550 600 650 700 750 30 150 200 250 300 350 400 450 500 550 600 650 700 750 COPPER AREA (mm2) COPPER AREA (mm2) Figure 34. qJA vs. Copper Spreader Area, DPAK 5-Lead Figure 35. qJA vs. Copper Spreader Area, D2PAK 5-Lead 100 Cu Area 167 mm2 Cu Area 736 mm2 R(t) C/W 10 1.0 sqrt(t) 0.1 0.01 0.0000001 0.000001 0.00001 0.0001 0.001 0.01 0.1 1.0 10 100 1000 TIME (sec) Figure 36. Single-Pulse Heating Curves, DPAK 5-Lead 100 Cu Area 167 mm2 Cu Area 736 mm2 R(t) C/W 10 1.0 0.1 0.01 0.0000001 0.000001 0.00001 0.0001 0.001 0.01 0.1 1.0 TIME (sec) Figure 37. Single-Pulse Heating Curves, D2PAK 5-Lead http://onsemi.com 15 10 100 1000 NCV4276, NCV4276A 100 RqJA 736 mm2 C/W 50% Duty Cycle 10 1.0 20% 10% 5% 2% 1% 0.1 Non-normalized Response 0.01 0.0000001 0.000001 0.00001 0.0001 0.001 0.01 0.1 1.0 10 100 1000 10 100 1000 PULSE WIDTH (sec) Figure 38. Duty Cycle for 1, Spreader Boards, DPAK 5-Lead 100 RqJA 788 mm2 C/W 50% Duty Cycle 10 1.0 20% 10% 5% 2% 1% 0.1 Non-normalized Response 0.01 0.0000001 0.000001 0.00001 0.0001 0.001 0.01 0.1 1.0 PULSE WIDTH (sec) Figure 39. Duty Cycle for 1, Spreader Boards, D2PAK 5-Lead http://onsemi.com 16 NCV4276, NCV4276A ORDERING INFORMATION Package Shipping NCV4276DT50RK DPAK, 5-Pin 2500 / Tape & Reel NCV4276DT50RKG DPAK, 5-Pin (Pb-Free) 2500 / Tape & Reel NCV4276DS50 D2PAK, 5-Pin 50 Units / Rail D2PAK, 5-Pin (Pb-Free) 50 Units / Rail NCV4276DS50R4 D2PAK, 5-Pin 800 / Tape & Reel NCV4276DS50R4G D2PAK, 5-Pin (Pb-Free) 800 / Tape & Reel NCV4276DT33RK DPAK, 5-Pin 2500 / Tape & Reel NCV4276DT33RKG DPAK, 5-Pin (Pb-Free) 2500 / Tape & Reel NCV4276DS33 D2PAK, 5-Pin 50 Units / Rail D2PAK, 50 Units / Rail Device Output Voltage Accuracy Output Voltage 5.0 V NCV4276DS50G 3.3 V NCV4276DS33G 5-Pin (Pb-Free) D2PAK, 5-Pin 800 / Tape & Reel D2PAK, 5-Pin (Pb-Free) 800 / Tape & Reel NCV4276DS25 D2PAK, 5-Pin 50 Units / Rail NCV4276DS25G D2PAK, 50 Units / Rail NCV4276DS33R4 NCV4276DS33R4G 4% 5-Pin (Pb-Free) 2.5 V D2PAK, 5-Pin 800 / Tape & Reel NCV4276DS25R4G D2PAK, 800 / Tape & Reel NCV4276DS18 D2PAK, 5-Pin 50 Units / Rail NCV4276DS18G D2PAK, 5-Pin (Pb-Free) 50 Units / Rail D2PAK, 5-Pin 800 / Tape & Reel NCV4276DS18R4G D2PAK, 5-Pin (Pb-Free) 800 / Tape & Reel NCV4276DTADJRKG DPAK, 5-Pin (Pb-Free) 2500 / Tape & Reel D2PAK, 5-Pin (Pb-Free) 50 Units / Rail NCV4276DS25R4 5-Pin (Pb-Free) 1.8 V NCV4276DS18R4 Adjustable NCV4276DSADJG NCV4276DSADJR4G NCV4276ADT50RKG 5.0 V NCV4276ADS50G NCV4276ADS50R4G NCV4276ADTADJRKG NCV4276ADSADJG 2% Adjustable NCV4276ADSADJR4G 800 / Tape & Reel DPAK, 5-Pin (Pb-Free) 2500 / Tape & Reel D2PAK, 5-Pin (Pb-Free) 50 Units / Rail 800 / Tape & Reel DPAK, 5-Pin (Pb-Free) 2500 / Tape & Reel D2PAK, 5-Pin (Pb-Free) 50 Units / Rail 800 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 17 NCV4276, NCV4276A PACKAGE DIMENSIONS DPAK 5, CENTER LEAD CROP DT SUFFIX CASE 175AA-01 ISSUE A -T- SEATING PLANE C B V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. E R R1 Z A S DIM A B C D E F G H J K L R R1 S U V Z 1 2 3 4 5 U K F J L H D G 5 PL 0.13 (0.005) M T SOLDERING FOOTPRINT 6.4 0.252 2.2 0.086 0.34 5.36 0.013 0.217 5.8 0.228 10.6 0.417 0.8 0.031 SCALE 4:1 http://onsemi.com 18 mm inches INCHES MIN MAX 0.235 0.245 0.250 0.265 0.086 0.094 0.020 0.028 0.018 0.023 0.024 0.032 0.180 BSC 0.034 0.040 0.018 0.023 0.102 0.114 0.045 BSC 0.170 0.190 0.185 0.210 0.025 0.040 0.020 --- 0.035 0.050 0.155 0.170 MILLIMETERS MIN MAX 5.97 6.22 6.35 6.73 2.19 2.38 0.51 0.71 0.46 0.58 0.61 0.81 4.56 BSC 0.87 1.01 0.46 0.58 2.60 2.89 1.14 BSC 4.32 4.83 4.70 5.33 0.63 1.01 0.51 --- 0.89 1.27 3.93 4.32 NCV4276, NCV4276A PACKAGE DIMENSIONS D2PAK 5 LEAD DS SUFFIX CASE 936A-02 ISSUE C -T- OPTIONAL CHAMFER A B U V M D M E H 1 2 3 4 5 0.010 (0.254) TERMINAL 6 S K T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 6. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. L P N G DIM A B C D E G H K L M N P R S U V R C SOLDERING FOOTPRINT INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.067 BSC 0.539 0.579 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.702 BSC 13.691 14.707 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN 8.38 0.33 1.702 0.067 10.66 0.42 16.02 0.63 1.016 0.04 3.05 0.12 SCALE 3:1 mm inches SMART REGULATOR is a registered trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 19 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative pubnumber/D