TS2940 1A Ultra Low Dropout Fixed Positive Voltage Regulator TO-263 Low Dropout Voltage 0.6V (typ.) Pin assignment: 1. Input 2. Ground 3. Output General Description The TS2940 series of fixed-voltage monolithic micro-power voltage regulators is designed for a wide range of applications. This device excellent choice of use in battery-power application. Furthermore, the quiescent current increases on slightly at dropout, which prolongs battery life. This series of fixed-voltage regulators features very low ground current (100uA Typ.) and very low drop output voltage (Typ. 60mV at light load and 600mV at 1A). This includes a tight initial tolerance of 1% typ., extremely good line regulation of 0.05% typ., and very low output temperature coefficient. This series is offered in 3-pin TO-263, TO-220, TO-252 & SOT-223 package. Features Dropout voltage typically 0.6V @Io=1A +30V Input over voltage protection Output current up to 1A +60V Transient peak voltage Output voltage trimmed before assembly Internal current limit -18V Reverse peak voltage Thermal shutdown protection Block Diagram Ordering Information Part No. Operation Temp. o -40 ~ +125 C TS2940CZxx TS2940CMxx Package TO-220 TO-263 o -40 ~ +85 C TS2940CPxx TO-252 TS2940CWxx SOT-223 Note: Where xx denotes voltage option, available are 5.0V, 3.3V, 2.5V and 1.8V. Contact factory for additional voltage options. Absolute Maximum Rating (Note 1) Input Supply Voltage (Note 2) Operation Input Supply Voltage Vin -18 ~ +60 V Vin (operate) 30V V PD Internally Limited Power Dissipation (Note 3) Operating Junction Temperature Range TJ Storage Temperature Range TSTG W -40 ~ +125 o C -65 ~ +150 o C Lead Soldering Temperature (260 oC) TS2940 TO-220 TO-263 Package 5 TO-252 / SOT-223Package 4 1-6 S 2003/12 rev. B Electrical Characteristics Vin = Vout + 5V, IL = 5mA, Co = 10uF, Ta = 25 oC, unless otherwise specified. Parameter Conditions Min Typ Max Unit 0.980|Vo| 5.0 / 3.3 1.020|Vo| V 0.970|Vo| 2.5 / 1.8 1.030|Vo| V Input Supply Voltage -- -- 26 V Output Voltage Temperature -- 50 150 ppm/ C Output Voltage Output Voltage 5mA IL 1A, Vo+5V Vin 26V o Coefficient Line Regulation Vo+2V Vin 26V -- 0.05 0.5 % Load Regulation 5mA IL 1A -- 0.2 1.0 % Dropout Voltage (Note 4) IL=100mA -- 100 200 IL=500mA -- 300 500 IL=800mA -- 600 800 IL=5mA -- 10 -- IL=800mA -- 30 -- Short Circuit Current (Note 6) Vout=0 -- -- 1.5 Output Noise, CL=2.2uF -- 500 -- 10Hz to 100KHz, IL=10mA CL=3.3uF -- 350 -- CL=33uF -- 120 -- Quiescent Current (Note 5) mV mA A uVrms Thermal Performance Condition Package type Typ Thermal Resistance TO-220 60 Junction to Ambient TO-263 80 TO-252 150 SOT-223 170 Unit o C/W Note 1: Absolute Maximum Rating is limits beyond which damage to the device may occur. For guaranteed specifications and test conditions see the Electrical Characteristics. Note 2: Maximum positive supply voltage of 60V must be limited duration (<100mS) and duty cycle (<1%). Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, Tj, the junction to ambient thermal resistance, ja, and the ambient temperature, Ta. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The effective value of ja can be reduced by using a heatsink. Note 4: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Note 5: Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the ground pin current and output load current. Note 6: Output current will decrease with increasing temperature, but it will be not dropped below 1A at the maximum specified temperature. TS2940 2-6 2003/12 rev. B Application Information The TS2940 series is a high performance with low dropout voltage regulator suitable for moderate to high current and voltage regulator application. Its 600mA(typ) dropout voltage at full load and over temperature makes it especially valuable in battery power systems and as high efficiency noise filters in post regulator applications. Unlike normal NPN transistor design, where the base to emitter voltage drop and collector to emitter saturation voltage limit the minimum dropout voltage, dropout performance of the PNP output of these devices is limited only by low Vce saturation voltage. The TS2940 series is fully protected from damage due to fault conditions. Linear current limiting is provided. Output current during overload conditions is constant. Thermal shutdown the device when the die temperature exceeds the maximum safe operating temperature. Transient protection allows device survival even when the input voltage spikes above and below nominal. The output structure of these regulators allows voltages in excess of the desired output voltage to be applied without reverse current flow. Typical Application Circuit A low ESR solid tantalum capacitor works extremely well and provides good transient response and stability over temperature. Aluminum electrolytic can also be used, as long as the ESR of the capacitor is <2ohm. The value of the output capacitor can be increased without limit. Higher capacitance values help to improved transient response and ripple rejection and reduce output noise. Minimum Load Current The TS2940 series is specified between finite loads. If the output current is too small leakage currents dominate and the output voltage rises. A 10mA minimum load current is necessary for proper regulation. Input Capacitor An input capacitor of 1uF or greater is recommended when the device is more that 4 inches away from the bulk AC supply capacitance or when the supply is a battery. Small and surface mount ceramic chip capacitors can be used for bypassing. Larger values will help to improve ripple rejection by bypassing the input to the regulator, further improving the integrity of the output voltage. Thermal Characteristics Output Capacitor The TS2940 series requires an output capacitor to maintain stability and improve transient response. Proper capacitor selection is important to ensure proper operation. The output capacitor selection is dependent upon the ESR of the output capacitor the maintain stability. When the output capacitor is 10uF or greater, the output capacitor should have an ESR less than 2 ohm. This will improve transient response as well as promoted stability. Ultra low ESR capacitors (<100mohm), such as ceramic chip capacitors may promote instability. These very low ESR levels may cause an oscillation and/or under damped transient response. A heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of the application. Under all possible operating conditions, the junction temperature must be within the range specified under absolute maximum ratings. To determine if the heatsink is required, the power dissipated by the regulator, PD must be calculated. The below formula shows the voltages and currents for calculating the PD in the regulator: Iin = IL / IG PD = (Vin-Vout) * IL + (Vin) * IG Ex. PD = (3.3V-2.5V) * 1A + 3.3V * 11mA = 800mW + 36mW = 836mW Remark: IL is output load current, IG is ground current. Vin is input voltage Vout is output voltage TS2940 3-6 2003/12 rev. B Application Information (continued) The next parameter which must be calculated is the maximum allowable temperature rise, TR(max). this is calculated by the using to formula: TR(max) = TJ(max) - TA(max) Where: TJ(max) is the maximum allowable junction temperature, which is 125 oC for commercial grade parts. IMPORTANT: if the maximum allowable value for is found to be 60 oC/W for the TO-220 package, 80 oC/W for the TO-263 package, 150 oC/W for the TO-252 package, or 170 oC/W for the SOT-223 package, no heatsink is needed since the package alone will dissipate enough heat to satisfy these requirements. If the calculated value for ja falls below these limits, a heatsink is required. TA(max) is the maximum ambient temperature which will be encountered in the application. Using the calculated values for TR(max) and PD, the maximum allowable value for the junction to ambient thermal resistance, ja, can now be found: ja = TR(max) / PD TS2940 4-6 2003/12 rev. B TO-220 Mechanical Drawing K B A TO-220 DIMENSION L C DIM P J I M D H F G O E N MILLIMETERS MIN MAX INCHES MIN MAX A 10.000 10.500 0.394 0.413 B 3.240 4.440 0.128 0.175 C D 2.440 - 2.940 6.350 0.096 - 0.116 0.250 E 0.381 1.106 0.015 0.040 F G 2.345 4.690 2.715 5.430 0.092 0.092 0.058 0.107 H 12.700 14.732 0.500 0.581 I J 8.382 14.224 9.017 16.510 0.330 0.560 0.355 0.650 K 3.556 4.826 0.140 0.190 L M 0.508 27.700 1.397 29.620 0.020 1.060 0.055 1.230 N 2.032 2.921 0.080 0.115 O P 0.255 5.842 0.610 6.858 0.010 0.230 0.024 0.270 TO-263 Mechanical Drawing TO-263 DIMENSION A E F B I H C G D TS2940 5-6 DIM MILLIMETERS MIN MAX INCHES MIN MAX A 10.000 10.500 0.394 0.413 B C 14.605 0.508 15.875 0.991 0.575 0.020 0.625 0.039 D 2.420 2.660 0.095 0.105 E F 4.064 1.118 4.830 1.400 0.160 0.045 0.190 0.055 G 0.450 0.730 0.018 0.029 H I 8.280 1.140 8.800 1.400 0.325 0.044 0.346 0.055 J 1.480 1.520 0.058 0.060 2003/12 rev. B TO-252 Mechanical Drawing E J TO-252 DIMENSION A F I B G C D H DIM MILLIMETERS INCHES A MIN 6.570 MAX 6.840 MIN 0.259 MAX 0.269 B 9.250 10.400 0.364 0.409 C D 0.550 2.560 0.700 2.670 0.022 0.101 0.028 0.105 E 2.300 2.390 0.090 0.094 F 0.490 0.570 0.019 0.022 G H 1.460 0.520 1.580 0.570 0.057 0.020 0.062 0.022 I 5.340 5.550 0.210 0.219 J 1.460 1.640 0.057 0.065 SOT-223 Mechanical Drawing A SOT-223 DIMENSION B DIM I C H J K D F G E TS2940 6-6 MILLIMETERS INCHES A MIN 6.350 MAX 6.850 MIN 0.250 MAX 0.270 B 2.900 3.100 0.114 0.122 C D 3.450 0.595 3.750 0.635 0.136 0.023 0.148 0.025 E 4.550 4.650 0.179 0.183 F G 2.250 0.835 2.350 1.035 0.088 0.032 0.093 0.041 H 6.700 7.300 0.263 0.287 I 0.250 0.355 0.010 0.014 J K 10 1.550 16 1.800 10 0.061 16 0.071 2003/12 rev. B