SW PANEL SWITCHES 30 -1 08 18 00 13000 series Professional quick-break momentary pushbutton switches DISTINCTIVE FEATURES PC and panel mount models Bushing O 6.35 (1/4) and 11.9 (15/32) UL and CECC approved ELECTRICAL SPECIFICATIONS * Max. current/voltage rating with resistive load : - silver contacts (A-AD2) : 4 A 30 VDC - gold plated contacts (CD) : 100 mA 30 V * Minimum load (AD2-CD contacts) : 10 mA 50 mV, 10 A 5 V min. * Initial contact resistance : 10 m max. * Insulation resistance : 1,000 M min. at 5 00VDC * Dielectric strength : 1,000 Vrms 50 Hz min. between terminals 2,000 Vrms 50 Hz min. between poles and between terminals and frame * Contact bounce : 2 ms max. * Electrical life : Contacts Max. current/voltage rating Number of cycles A 4 A 30 VDC 50,000 AD2 4 A 30 VDC (gold plating : 100 mA 30 VDC max.) 20,000 CD 100 mA 30 VDC 50,000 Low level or mechanical life 150,000 GENERAL SPECIFICATIONS * Torque : 1.25 Nm (.922 Ft.lb) max. applied to nut * Standard panel thickness : 2 mm (.078 ) max. * Total travel : 2 mm (.078) * Operating temperature : -40 C to +85 C (-40 F to +185 F) The company reserves the right to change specifications without notice. 1 Professional quick-break momentary pushbutton switches MATERIALS TERMINALS * Case : diallylphthalate (DAP) * Bushing : brass, nickel plated 1.20 (.047) * Housing : brass, nickel plated * Contacts : A : silver AD2 : silver, gold plated (2 micron gold) CD : brass, gold plated 2.50 (.098) 1.00 (.039) 9.50 (.374) 5.00 (.196) 1.70 (.066) * Actuator : brass, nickel plated ELECTRICAL FUNCTION * Terminal seal : epoxy APEM products may be recycled at end-of-life for the re-claiming of valuable metal components. KEYWAY Note : AD2 contacts can be used for high level applications.In this case, the gold layer is considered only as a protection against oxidation during storage. RELIABILITY - RUN-IN TEST 1 2 3 Upon request, each individual switch can be submitted to a low level run-in test of 50 or 250 cycles to ensure suitability for special applications requiring a very high level of reliability (military, space,etc.). PANEL CUT-OUT FOR O 6,35 (1/4) BUSHING 2 A 125 VAC/250 VAC 5.20 (.204) O2.20 (.086 DIA) O2.20 (.086 DIA) 5.20 (.204) Standard Standard CECC 96401-001 O2.20 (.086 DIA) O6.50 (.255 DIA) O6.50 (.255 DIA) Designed to MIL specifications Availability : UL : all models 5.20 with silver or gold plated silver contacts. (.204) factory for details of approved 2.70 CECC : consult models. (.106) Marking : to order switches marked UL or CECC, Standard K complete appropriate box of ordering format. 2 2.70 (.106) X640 With X640 sealing option O6.50 (.255 DIA) O6.50 (.255 DIA) 2.70 (.106) Standard O6.50 (.255 DIA) O6.50 (.255 DIA) 2.70 (.106) K 1.10 (.043) AGENCY APPROVALS O6.50 (.255 DIA) 1.10 (.043) O6.50 (.255 DIA) 1.10 (.043) PANEL SWITCHES 13000 series K With K sealing option O6 (.255 2.70 (.106) X6 Professional quick-break momentary pushbutton switches BUILD YOUR PART NUMBER BASIC PART NUMBER 13 SERIES TERMINALS AND BUSHINGS 2 Straight PC terminals, bushing O 6.35 (1/4) 4 Solder lugs, bushing O 6.35 (1/4) or 11.9 (15/32) Right angle terminals, bushing O 6.35 (1/4) NUMBER OF POLES 3 Single pole 4 Double pole ELECTRICAL FUNCTION 5 TERMINALS ON - MOM Blank W Solder lugs or straight PC depending on model Right angle, horizontal mounting OPTIONS ORDER SEPARATELY. CONTACT MATERIALS A FINISH Blank Silver AD2 Silver, gold plated (2 micron gold) CD Brass, gold plated G SPECIAL OPTIONS Brass, nickel plated Black finish on bushing, plunger and hardware Blank No special requirement X640 Reinforced sealing by three O-rings X935 C-ring on plunger for positive stop X768 Bushing O 11.9 (15/32) + front panel sealing (double pole only) CAPS U900 O 5 (.196) U1140 O 8 (.314) U1720 O 9.4 (.370) U480 O 10 (.393) std U630 O 15 (.590) U2430 Square, height 4 (.157) U2020 Square, height 6 (.236) For models with O 4 (.157) plunger only. PLUNGERS Blank Standard for O 6.35 (1/4) bushing -4 4 mm (.157) long, for O 11.9 (15/32) bushing (X768) -9 9 mm (.354) long, for O 11.9 (15/32) bushing (X768) SEALING Blank Epoxy sealed terminals standard K Front panel sealing by one O-ring and sealing washer APPROVALS UL CECC Consult factory for details of approved models. Reinforced sealing, see X640 under "Special options". ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart. Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information. Sealing boots are available to protect the switches against dust and water. See "Sealing Boots" section of website. Mounting accessories : standard hardware supplied with all models : 2 hex nuts 8 mm (.314) across flats, 1 locking ring and 1 lockwasher. Standard and special hardware is presented in the "Hardware" section of website. 3 PANEL SWITCHES 13000 series Professional quick-break momentary pushbutton switches KEYWAY O 6.35 BUSHING SOLDER LUG TERMINALS : 13400 EPOXY MOM 2 3 O6.35-40UNS (1/4-40UNS) 4.00 (.157) 6.00 (.236) EPOXY 4.00 (.157) 1.00 (.039) ON 1 0.50 (.019) MOM 4.00 (.157) MOM 14.00 (.551) 13.40 (.527) ON Double pole 13245 6.00 (.236) O1.6 (.062 DIA) 0.70 (.027) 1-2 6.30 (.248) 1-3 O4.00 (.157 DIA) 6.00 (.236) 8.00 (.314) 9.50 (.374) 13235 0.50 (.019) KEYWAY O 6.35 BUSHING STRAIGHT PC TERMINALS : 13200 Single pole 5.00 (.196) ON 3 4.00 (.157) 2.50 (.098) 6.00 (.236) KEYWAY O 6.35 BUSHING RIGHT ANGLE TERMINALS O6.35-40UNS (1/4-40UNS) 13445 2 13.40 (.527) MOM Double pole 1 0.70 (.027) ON 14.00 (.551) 1-2 O4.00 (.157 DIA) O1.6 (.062 DIA) 5.08 (.200) 1-2 13445 -4 X768 ON MOM With long plunger 13445 -9 X768 ON MOM Chrome plated actuator. Switch guard available for this model : see "Switch guards" section of website. 4 13.40 (.527) 0.70 (.027) O8.00 (.314 DIA) 3 2 1 9.00 (.354) 7.50 (.295) O8.00 (.314 DIA) 14.20 (.559) 1-3 CD13WDT-A FLAT SEALED SWITCH WITH O 11.9 FLATTED BUSHING : X768 - SOLDER LUG TERMINALS Single pole with short plunger 4.00 (.157) 14.20 (.559) O12.00 (.472 DIA) 1.50 (.059) MOM 3 0.50 (.019) O11.9 32UNS (.468-32UNS) ON 4.40 (.173) EPOXY 2 4.00 (.157) 4.00 (.157) EPOXY 6.00 (.236) Short (-4) 5.00 (.196) 1-2 1 5.90 (.232) 2.60 (.102) 9.27 (.364) 13435W 1-3 1.00 (.039) Single pole 9.27 (.364) 0.40 (.015) 8.00 (.314) 6.00 (.236) 13435 1-3 6.30 (.248) Single pole 6.00 (.236) 8.00 (.314) O6.35-40UNS (1/4-40UNS) O4.00 (.157 DIA) 4.00 (.157) PANEL SWITCHES 13000 series 4.00 (.157) 2.50 (.098) 0.50 (.019) Long (-9) 5.10 (.200) CD EC Professional quick-break momentary pushbutton switches CONTACTS MATERIALS BASIC P/N A AD2 CD Silver Silver, gold plated (2 micron gold) Brass, gold plated PLUNGERS BASIC P/N Dash compulsory before plunger code. Blank Standard plunger for O 6.35 (1/4) bushing -4 4 mm (.157) long plunger for O 11.9 (15/32) bushing (X768 option) -9 9 mm (.354) long plunger for O 11.9 (15/32) bushing (X768 option) FINISH BASIC P/N Blank Bright chrome finish GBlack finish on bushing, actuator and hardware SEALING O-ring O10.60 (.417 DIA) 1 2.00 Maxi (.078 MAX) K Front panel sealing by one O-ring and sealing washer. Protects the switch against water and dust. Panel seal withstands 1 bar pressure and remains sealed even when switch is operated. 2.30 (.090) BASIC P/N O11.80 (.464 DIA) Reinforced sealing : see X640 under "Special options". 2 O5.80 (.228 DIA) O6.40 (.251 DIA) Sealing washer SPECIAL OPTIONS X640 Front panel sealing by three O-rings. Flatted bush for precise orientation. Protects the switch against water and dust. Panel seal withstands 1 bar pressure and remains sealed even when switch is operated. Available on models with O 6.35 (1/4) bushing only. X935 4.00 Maxi (.157 MAX) BASIC P/N C-ring on plunger for positive stop X768 Sealed switch with O 11.9 (15/32) flatted bushing. Chrome plated actuator. Solder lug terminals, double pole. Contact and finish options available. See above. X640 1 O-rings 5 PANEL SWITCHES 13000 series PANEL SWITCHES 13000 series Professional quick-break momentary pushbutton switches AGENCY APPROVALS BASIC P/N UL CECC Blank CECC 96401-001 No agency approval required. Availability UL : all models with silver or gold plated silver contacts CECC : consult factory for details of approved models. Marking To order switches marked UL or CECC, please complete above box with desired approval. 6