(R) January 16th, 2013 Document-No.: DB_PCapO2-EVA-Kit_en V0.0 (R) PCapO2 Published by acam -messelectronic gmbh (c)acam-messelectronic gmbh 2013 Disclaimer / Notes "Preliminary" product information describes a product which is not in full production so that full information about the product is not available yet. Therefore, acam -messelectronic gmbh ("acam") reserves the right to modify this product without notice. The information provided by this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by acam for its use, nor for any infringements of patents or other rights of third parties that may result from its use. The information is subject to change without notice and is provided "as is" without warranty of any kind (expressed or implied). (R) is a registered trademark of acam. All other brand and product names in this document are trademarks or service marks of their respective owners. Support / Contact For a complete listing of Direct Sales, Distributor and Sales Representative contacts, visit the acam web site at: http://www.acam.de/sales/distributors/ For technical support you can contact the acam support team in the headquarters in Germany or the Distributor in your country. The contact details of acam in Germany are: support@acam.de or by phone +49-7244-74190 acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 Content 1 2 3 4 Introduction .............................................................................................. 1-2 1.1 General .............................................................................................. 1-2 1.2 Component List .................................................................................... 1-2 Connecting Capacitors and Resistors ............................................................. 2-4 2.1 Capacitance Measurement ..................................................................... 2-4 2.2 Temperature Measurement .................................................................... 2-5 2.3 Pulse Code Generation .......................................................................... 2-6 2.4 Motherboard ....................................................................................... 2-6 Miscellaneous ........................................................................................... 3-1 3.1 Literature Guide ................................................................................... 3-1 3.2 Document History ................................................................................ 3-2 Appendix .................................................................................................. 4-1 4.1 Schematics ......................................................................................... 4-1 4.2 Layout ................................................................................................ 4-3 acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 1-1 (R) 1 Introduction 1.1 General PCapO2 The PCapO2-EVA-KIT evaluation system provides a complete system for generally evaluating the PCapO2 chip. It comprises of a main board, a plug-in module, a Windows based evaluation software, assembler software and the PicoProg V2.0 programming device. The PCapO2 evaluation board is connected to the PC`s USB interface through the PicoProg V2.0 programming device. The evaluation kit offers user friendly configurations for evaluating the PCapO 2 single-chip solution for capacitance measurement. This kit can be used to evaluate the capacitance measurement, temperature measurement and the pulse generation capa bilities of the PCapO2 chip. For a proper use of the evaluation system it is strongly recommended to refer to the current data sheet of the PCapO2 device. You can download these data sheets from www.acam.de/download-center/picocap . 1.2 Component List PCapO1-MB Motherboard PCapO2-AD Plug-in module Based on PCapO2-AD in QFN32 package PicoProg V2.0 Programmer High density DSUB15 cable Connecting the Evaluation board to the programmer 1-2 USB cable Connects PicoProg V2.0 to the PC Wall power supply unit 9 V CD-ROM Includes software and data sheets acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 Figure 1-1: Components of the evaluation kit acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 1-3 (R) 2 PCapO2 Connecting Capacitors and Resistors This evaluation kit can be used for evaluating capacitance measurement by connecting capacitive sensors. Further, it can be used for evaluating temperature measurement by connecting external temperature sensitive resistors or for generating quasi analog voltage (pulse width/density modulated) that is dependent on the sensor connected to the system. Depending on the purpose of evaluation, a modification has to be made to the same plug-in module. Following is a picture of the Mother board with the plug-in module. Figure 2-1: The evaluation kit's motherboard and plug-in module The following sections describe the modifications for each application in detail. 2.1 Capacitance Measurement For the purpose of evaluating the capacitance measurement Reference capacitor 47 pF Ceramic capacitors 47 pF each using PCapO2, the plug-in module is pre-assembled with ceramic capacitors to emulate capacitive sensors. These capacitors, each 47pF in value, are connected to the 8 ports PC0 to PC7. They are connected as single sensors in floating mode, i.e. each capacitor is connected between 2 ports, and hence there are 4 x 47pF on-board capacitors. Please refer to section 3 of the PCapO2 data sheet for more information on how to connect capacitors to the chip. The capacitor connected between ports PC0 and PC1 is taken as the reference capacitor. Figure 2-2: Details of the plug-in module 2-4 acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 In the process of evaluation, when you are comfortable with interpreting the measurement results from the chip, these fixed capacitors can be replaced with the actual capacitive sensors of your application. If you want to connect your capacitive sensors in grounded mode, then GND points are provided at the two ends of the module, where the sensor ground connections ought to be soldered. The typical value of the capacitive sensors that can be connected to the evaluation kit lies in the range of 30pF to 3.5nF. The reference capacitor should be in the same order of magnitude as the sensor. Depending on the value of the sensor, the value of the internal resistor for performing the measurement has to be selected. For the pre-assembled 47pF capacitors, an internal discharge resistor of 180kOhm works well. See section 3 of the PCapO2 data sheet on how to select the value of the internal discharge resistor. 2.2 Temperature Measurement Temperature measurement or other resistive tasks may also be of interest for the user of this kit. The evaluation kit offers this possibility through the RDC (resistive-to-digital converter) ports. An on-chip thermistor coupled with an on-chip temperature-stable reference resistor made of polysilicon is sufficient for observing the temperature measurement capability of the PCapO2 chip. Port PT1 for 2nd external temperature sensor (not supported by the standard firmware) Port PT0 for external temperature sensor Port PT2 for external reference resistor 33 nF COG Figure 2-3: Temperature sensor connection pads However, there is a possibility to connect the reference resistor and the thermistor externally to the chip, too. In case of external resistors, the temperature-stable reference resistor ought to be connected at port PT2REF on the plug-in module. The module allows you to connect the external acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 2-5 (R) PCapO2 thermistor, e.g. a PT1000 sensor at port PT0 (or PT1, not supported yet by the standard firmware). In any case, for the temperature measurement, an external capacitor 33 nF C0G has to be connected to the chip; it is already pre-assembled on board. 2.3 Pulse Code Generation Any of the capacitance or temperature measurement results from the PCapO2 chip can be given out as a pulse width modulated or pulse density modulated signal. This output can be filtered to generate an analog output signal that can be used for further controlling. These pulse width or pulse density codes can be generated at Ports PG0, PG1, PG2 or PG3. Since ports PG0 and PG1 are used for the SPI Interface in the module, the hardware allows to get a valid pulse width/density modulated signal on PG2 or PG3. However, when I2C communication mode is used the pulsed signals can be optionally obtained on the ports PG0 and PG1. PG3 PG2 PG0 PG1 Figure 2-4: General purpose interface ports PG0 to PG3 2.4 Motherboard The motherboard connects to the PicoProg V2.0 programmer. It serves the various power options. It can be powered via wall plug supply, the voltage being set from 1.8V to 4.5V by jumpers. Further, it supports a battery power option. Power present is indicated by a green LED. 2-6 acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 There is a jumper `Current' on the mother board. The current consumption of the PCapO2 chip during operation can be directly measured from these jumper terminals. All interface signals and general purpose I/O signals can be monitored by means of a separate jumper. acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 2-7 (R) 2-2 acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 PCapO2 3 Miscellaneous 3.1 Literature Guide Title Document-No PCapO2A Single-chip Solution for Capacitance Measurement Volume 1: General data and front-end description DB_PCap02A_Vol1_en.pdf PCapO2Ax-DSP Single-chip Solution for Capacitance Measurement Volume 2: Digital Signal Processor DB_PCap02A_Vol2_en.pdf PCapO2-EVA-Kit Evaluation System for PCapO2 DB_PCap02-EVA-Kit_en.pdf PCapO2plus Evaluation Software for PICOCAP Devices DB_PCap02plus_en.pdf PCap Assembler Assembler Software for PICOCAP Devices DB_PCap-Assembler_en.pdf Title Document-No Title Document-No The latest versions of the available documents can be downloaded from the acam website at: http://www.acam.de/download-center/picocap acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 3-1 (R) 3.2 Document History 16.01.2013 3-2 PCapO2 First release acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 4 4.1 Appendix Schematics Figure 4-1: Motherboard schematics acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 4-1 (R) Figure 4-2: PCa02 AD module schematics 4-2 acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de PCapO2 PCapO2 4.2 Layout Figure 4-3: PCa02 AD module layout acam messelectronic gmbh - Friedrich-List-Str.4 - 76297 Stutensee - Germany - www.acam.de 4-3 acam-messelectronic gmbh Friedrich-List-Strae 4 76297 Stutensee-Blankenloch Germany Phone +49 7244 7419 - 0 Fax +49 7244 7419 - 29 E-Mail support@acam.de www.acam.de