Ericsson Internal PRODUCT TABLE OF CONTENTS SPECIFICATION E Prepared (also subject responsible if other) EFEIDEN SEC/S Thomas Deng Approved BMR 603 EAB/FJB/GKF SEC/D (Julia1203/1 You) (Natalie Natalie) 1 (1) (4) No. 001521/1301-BMR EN/LZT146393 603Technical 1203/1 UenSpecification Checked Date MICJOHN 2008-3-13 2008-8-28 Rev DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Reference EN/LZT 146 393 R1E September 2008 A D (c) Ericsson Power Modules AB Key Features * Low profile SMD 50.2 x 46.0 x 8.1 mm (1.98 x 1.81 x 0.32 in.) * Low profile, max 8.7mm (0.343 in.) * High efficiency, typ. 87 % at full load * Functional input to output isolation on 78V output * Operates in direct parallel configuration for higher power * More than 2.7 million hours MTBF * Designed for POTS applications General Characteristics * Suited for narrow board pitch applications (15 mm/0.6 in) * Input under voltage shut-down * Over temperature protection * Over current protection * Soft start * Remote Control * ISO 9001/14001 certified supplier Design for Environment Meets requirements in hightemperature lead-free soldering processes. Contents General Information Safety Specification Absolute Maximum Ratings ............................................................. 2 ............................................................. 3 ............................................................. 4 BMR 603 1203/1 78/-52/-33V Electrical Specification ............................................................. 5 EMC Specification Operating Information Thermal Consideration Connections Mechanical Information Soldering Information Delivery Information Product Qualification Specification ............................................................. 9 ........................................................... 10 ........................................................... 11 ........................................................... 12 ........................................................... 13 ........................................................... 15 ........................................................... 16 ........................................................... 17 Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) EFEIDEN Approved BMR 603 SEC/D (Julia1203/1 You) 2 (4) No. Checked 1/1301-BMR 603Technical 1203/1 UenSpecification Date 2008-8-28 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W General Information Ordering Information See Contents for individual product ordering numbers. Reliability The Mean Time Between Failure (MTBF) is calculated at full output power and an operating ambient temperature (TA) of +40C, which is a typical condition in Information and Communication Technology (ICT) equipment. Different methods could be used to calculate the predicted MTBF and failure rate which may give different results. Ericsson Power Modules currently uses one method Telcordia SR332. Predicted MTBF for the series is: 2.7 million hours according to Telcordia SR332, issue 1, Black box technique. The Ericsson failure rate data system is based on field tracking data. The data corresponds to actual failure rates of components used in Information Technology and Telecom (IT&T) equipment in temperature controlled environments (TA = -5...+65C). Telcordia SR332 is a commonly used standard method intended for reliability calculations in IT&T equipment. The parts count procedure used in this method was originally modelled on the methods from MIL-HDBK-217F, Reliability Predictions of Electronic Equipment. It assumes that no reliability data is available on the actual units and devices for which the predictions are to be made, i.e. all predictions are based on generic reliability parameters. Compatibility with RoHS requirements The products are compatible with the relevant clauses and requirements of the RoHS directive 2002/95/EC and have a maximum concentration value of 0.1% by weight in homogeneous materials for lead, mercury, hexavalent chromium, PBB and PBDE and of 0.01% by weight in homogeneous materials for cadmium. Rev 2 Reference EN/LZT 146 393 R1E September 2008 D (c) Ericsson Power Modules AB Exemptions in the RoHS directive utilized in Ericsson Power Modules products include: Lead in high melting temperature type solder (used to solder the die in semiconductor packages) Lead in glass of electronics components and in electronic ceramic parts (e.g. fill material in chip resistors) Lead as an alloying element in copper alloy containing up to 4% lead by weight (used in connection pins made of Brass) Quality Statement The products are designed and manufactured in an industrial environment where quality systems and methods like ISO 9000, 6 (sigma), and SPC are intensively in use to boost the continuous improvements strategy. Infant mortality or early failures in the products are screened out and they are subjected to an ATE-based final test. Conservative design rules, design reviews and product qualifications, plus the high competence of an engaged work force, contribute to the high quality of our products. Warranty Warranty period and conditions are defined in Ericsson Power Modules General Terms and Conditions of Sale. Limitation of Liability Ericsson Power Modules does not make any other warranties, expressed or implied including any warranty of merchantability or fitness for a particular purpose (including, but not limited to, use in life support applications, where malfunctions of product can cause injury to a person's health or life). Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) EFEIDEN Approved BMR 603 SEC/D (Julia1203/1 You) 3 (4) No. Checked 1/1301-BMR 603Technical 1203/1 UenSpecification Date 2008-8-28 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Rev 3 Reference EN/LZT 146 393 R1E September 2008 D (c) Ericsson Power Modules AB Safety Specification General information Ericsson Power Modules DC/DC converters and DC/DC regulators are designed in accordance with safety standards IEC/EN/UL60950, Safety of Information Technology Equipment. IEC/EN/UL60950 contains requirements to prevent injury or damage due to the following hazards: * * * * * * Electrical shock Energy hazards Fire Mechanical and heat hazards Radiation hazards Chemical hazards On-board DC-DC converters are defined as component power supplies. As components they cannot fully comply with the provisions of any Safety requirements without "Conditions of Acceptability". It is the responsibility of the installer to ensure that the final product housing these components complies with the requirements of all applicable Safety standards and Directives for the final product. Component power supplies for general use should comply with the requirements in IEC60950, EN60950 and UL60950 "Safety of information technology equipment". There are other more product related standards, e.g. IEEE802.3af "Ethernet LAN/MAN Data terminal equipment power", and ETS300132-2 "Power supply interface at the input to telecommunications equipment; part 2: DC", but all of these standards are based on IEC/EN/UL60950 with regards to safety. Ericsson Power Modules DC/DC converters and DC/DC regulators are UL60950 recognized and certified in accordance with EN60950. The flammability rating for all construction parts of the products meets requirements for V-0 class material according to IEC 60695-11-10. The products should be installed in the end-use equipment, in accordance with the requirements of the ultimate application. Normally the output of the DC/DC converter is considered as SELV (Safety Extra Low Voltage) and the input source must be isolated by minimum Double or Reinforced Insulation from the primary circuit (AC mains) in accordance with IEC/EN/UL60950. 24 V DC systems The input voltage to the DC/DC converter is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions. 48 and 60 V DC systems If the input voltage to the DC/DC converter is 75 Vdc or less, then the output remains SELV (Safety Extra Low Voltage) under normal and abnormal operating conditions. Single fault testing in the input power supply circuit should be performed with the DC/DC converter connected to demonstrate that the input voltage does not exceed 75 Vdc. If the input power source circuit is a DC power system, the source may be treated as a TNV2 circuit and testing has demonstrated compliance with SELV limits and isolation requirements equivalent to Basic Insulation in accordance with IEC/EN/UL60950. Non-isolated DC/DC regulators The input voltage to the DC/DC regulator is SELV (Safety Extra Low Voltage) and the output remains SELV under normal and abnormal operating conditions. Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) MICMALE Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) 1 (5) No. Checked 2/1301-BMR 603Technical 1203/1 UenSpecification Date (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Rev 4 Reference EN/LZT 146 393 R1E September 2008 D (c) Ericsson Power Modules AB Absolute Maximum Ratings Characteristics min Tref Operating Temperature (see Thermal Consideration section) TS Storage temperature VI Input voltage VRC Positive logic option Remote Control pin voltage (see Operating Information section) typ max Unit -40 +105 C -55 +125 C -0.5 +75 V -0.5 +75 V Stress in excess of Absolute Maximum Ratings may cause permanent damage. Absolute Maximum Ratings, sometimes referred to as no destruction limits, are normally tested with one parameter at a time exceeding the limits of Output data or Electrical Characteristics. If exposed to stress above these limits, function and performance may degrade in an unspecified manner. Fundamental Circuit Diagram GND RC -IN GND Bias Regulator, Control and Supervision OUT3 OUT2 OUT1 RETURN1 Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) 2 (5) No. MICMALE Approved Checked BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) 2/1301-BMR 603Technical 1203/1 UenSpecification Date Rev (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W 5 Reference EN/LZT 146 393 R1E September 2008 D (c) Ericsson Power Modules AB 78V, -52V, -33V / 32W Electrical Specification Tref = -30 to +95C, VI = 40 to 72 V, unless otherwise specified under Conditions. Typical values given at: Tref = +25C, VI= 53 V, max IO unless otherwise specified under Conditions. Characteristics Conditions min typ max Unit 40 53 72 V VI Input voltage range VIoff Turn-off input voltage Decreasing input voltage 33 VIon Turn-on input voltage Increasing input voltage 34.5 V CI Internal input capacitance 2 F PO max Output power Pd 32 Efficiency at 50% of max power IO1 = 0,015 A, IO2 = 0,25 A, IO3 = 0,090A Efficiency at max power IO1 = 0,015 A, IO2 = 0,50 A, IO3 = 0,090A 84 Power Dissipation at max power IO1 = 0,015 A, IO2 = 0,50 A, IO3 = 0,090A 6.1 V W 80 % W Pli Input idling power IO = 0 A, VI = 53 V 2.5 W PRC Input standby power VI = 53 V (turned off with RC) 0.12 W fs Switching frequency 510 kHz Characteristics Conditions VOi Output voltage initial setting and accuracy Tref =+25C, VI = 53 V, IO1, IO2, IO3 = 0.1 x Inom Output Voltage IO1, IO2, IO3 0.1 x Inom Idling voltage IO = 0 A Line regulation IO = IO VO max, VI = 42....72 V min / typ / max Output 1 Output 2 Output 3 Unit typ 78.0 +/- 2% -52.7 +/- 1% -33.2 +/- 1% V min 71.6 -49,0 -30.9 V max 81.6 -54.2 -33.83 V typ 77 -52.5 -33.3 V typ 1 0.6 0.5 % max - 110 50 mV typ - 250 200 mV typ - 150 150 s Vtr Load transient voltage deviation ttr Load transient recovery time TA = +25C , VI = 53 V, IO=20mA to 200 mA IO = 30...60 mA, 10Hz on output 2&3 VI = 53 V Slew rate = 0.01A/ s tr Ramp-up time (from 10-90% of VOi) IO = IO max, V O = 0.1...0.9 x V O typ 2.5 2.5 2.5 ms IO =0.1...1.0 x IO max, VI = 53 V from VI connection to Vo = 0.9 x VO typ 7 7 7 ms Load regulation output ts Start-up time (from VI connection to 90% of VOi) tRC RC start-up time IO Output current (continuous) Ilim Current limit threshold Isc Short circuit current VOac Output ripple & noise OVP Over voltage protection IO1 = IO2 = 50 % of max IO typ 7 7 7 ms max 80 500 800 mA TC < TC max min 200mA Tref = 25C typ - 1.2 2 A max 100 100 100 mVp-p typ 90 -60 -38 V See ripple & noise section, max IO, VOi, 20Hz ....5MHz Tref = +25 C, VI = 53 V, 0-100 % of max PO Total power limitation 35 W Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) 3 (5) No. MICMALE Approved 2/1301-BMR 603Technical 1203/1 UenSpecification Checked BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) Date Rev 6 Reference EN/LZT 146 393 R1E September 2008 (MICANWO) 2008-09-05 D DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W (c) Ericsson Power Modules AB 78V, -52V, -33V / 32W Electrical Specification Efficiency Power Dissipation [W] 10 [%] 95 8 90 6 85 40 V 80 53 V 72 V 75 40 V 4 53 V 72 V 2 0 70 0,0 0,1 0,2 0,3 0,4 0,5 0,0 0,6 [A] Efficiency vs. load current (Io2) and input voltage. Tref = +25C, Io1=15mA, Io3=90mA 0,1 0,2 0,3 0,4 0,5 0,6 [A] Dissipated power vs. load current (Io2) and input voltage. Tref = +25C, Io1=15mA, Io3=90mA Current Limit Characteristic, Vo2 Current Limit Characteristic, Vo3 [V] [V] 50,0 30,0 40,0 40 V 30,0 53 V 20,0 72 V 10,0 20,0 40 V 53 V 10,0 72 V 0,0 0,5 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 [A] 0,0 0,5 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 [A] Vo2 vs. load current (Io2)and input voltage. Tref = +25C, Io1=Io3=0 Vo3 vs. load current (Io3)and input voltage. Tref = +25C, Io1=Io2=0 Thermal current derating Output Voltage Temperature Characteristics, Vo3 Thermal output current derating 34,0 33,0 32,0 31,0 -40 -20 0 20 40 60 80 100 0,6 Max available output current (Io3) in [A] Vi min Vi nom Vi max Natural convection 1 m/s 0,5 0,4 0,3 0,2 0,1 0 40 50 60 70 80 90 100 Ambient Temperature [deg C] Vo3 vs. ref. temperature, Io1= 50mA, Io2=250mA, Io3=400mA Maximum output current (Io3) vs. ambient temperature. VI = 53 V, Io1=0.08A, Io2=0.2A. See also Thermal Consideration section. Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) MICMALE Approved 4 (5) No. BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) Checked 2/1301-BMR 603Technical 1203/1 UenSpecification Date (MICANWO) 2008-09-05 Rev Reference EN/LZT 146 393 R1E September 2008 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W D (c) Ericsson Power Modules AB 78V, -52V, -33V / 32W Electrical Specification Start-up Shut-down Place your graph here Start-up enabled by connecting VI at: Tref = +25C, VI = 53 V, IO1 = 80 mA, IO2 = 250 mA , Io3=400 mA, resistive load. Top trace: output voltage 1 (50 V/div.). Second trace: output voltage 2 (50 V/div.). Third trace: output voltage 3 (50 V/div.). Bottom trace: input voltage (100 V/div.). Time scale: (5 ms/div.). Output Ripple & Noise, Vo1 Output voltage ripple at: Tref = +25C, VI = 53 V, IO1 = 80 mA, IO2 = 250 mA , Io3=400 mA, resistive load. Top trace: output voltage 1 (50 V/div.). Second trace: output voltage 2 (50 V/div.). Third trace: output voltage 3 (50 V/div.). Bottom trace: input voltage (100 V/div.). Time scale: (5 ms/div.). Output Ripple & Noise, Vo2 Top trace: output voltage 1 (50mV/div.). Time scale: (1 s/div.). Output Ripple & Noise, Vo3 Output voltage ripple at: Tref = +25C, VI = 53 V, IO1 = 80 mA, IO2 = 250 mA , Io3=400 mA, resistive load. Shut-down enabled by disconnecting VI at: Tref = +25C, VI = 53 V, IO1 = 80 mA, IO2 = 250 mA , Io3=400 mA, resistive load. Top trace: output voltage 3 (50mV/div.). Time scale: (1 s/div.). Output voltage ripple at: Tref = +25C, VI = 53 V, IO1 = 80 mA, IO2 = 250 mA , Io3=400 mA, resistive load. Top trace: output voltage 2 (50mV/div.). Time scale: (1 s/div.). 7 Ericsson Internal PRODUCT SPECIFICATION E Prepared (also subject responsible if other) MICMALE Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) Checked 2/1301-BMR 603Technical 1203/1 UenSpecification Date (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Output Load Transient Response, Vo2 Output voltage response to load current stepchange, output 2 (30mA-60mA-30mA) dI/dt=0,01A/us Tref =+25C, VI = 53 V IO1 =8mA, Io3=80mA. 5 (5) No. Top trace: output voltage 2 (500 mV/div.). Mid trace: output voltage 3 (500 mV/div.). Bottom trace: load current (20 mA/div.). Time scale: (0.1 ms/div.). Rev Reference EN/LZT 146 393 R1E September 2008 D (c) Ericsson Power Modules AB Output Load Transient Response, Vo3 Output voltage response to load current step-change, output 3 (30mA-60mA-30mA) dI/dt=0,01A/us Tref =+25C, VI = 53 V IO1 =8mA, Io2=50mA. Top trace: output voltage 2 (200 mV/div.). Mid trace: output voltage 3 (200 mV/div.). Bottom trace: load current (20 mA/div.). Time scale: (0.1 ms/div.). 8 E Ericsson Internal PRODUCT SPECIFICATION Prepared (also subject responsible if other) 1 (5) No. 3/1301-BMR 603Technical 1203/1 UenSpecification MICMALE Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) Checked Date (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Rev 9 Reference EN/LZT 146 393 R1E September 2008 C (c) Ericsson Power Modules AB EMC Specification Conducted EMI measured according to EN55022, CISPR 22 and FCC part 15J (see test set-up). See Design Note 009 for further information. The fundamental switching frequency is 510 kHz for BMR 603 1203/1 @ VI = 53 V, max IO. Conducted EMI Input terminal value (typ) Test set-up Layout recommendation EMI without filter External filter (class B) Required external input filter in order to meet class B in EN 55022, CISPR 22 and FCC part 15J. The radiated EMI performance of the DC/DC converter will depend on the PCB layout and ground layer design. It is also important to consider the stand-off of the DC/DC converter. If a ground layer is used, it should be connected to the output of the DC/DC converter and the equipment ground or chassis. A ground layer will increase the stray capacitance in the PCB and improve the high frequency EMC performance. Filter components: Output ripple and noise L1 - Vin C1 C1,2,3 = 1 F C4 = 100 F L1,2 = 10 H L2 C2 C3 Output ripple and noise measured according to figure below. See Design Note 022 for detailed information. C4 DC-DC Output ripple and noise test setup EMI with filter E Ericsson Internal PRODUCT SPECIFICATION Prepared (also subject responsible if other) 3/1301-BMR 603Technical 1203/1 UenSpecification MICMALE Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) 2 (5) No. Checked Date (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Operating information Input Voltage The input voltage range 36 to 75Vdc meets the requirements of the European Telecom Standard ETS 300 132-2 for normal input voltage range in --48 and --60 Vdc systems, -40.5 to 57.0 V and --50.0 to -72 V respectively. At input voltages exceeding 75 V, the power loss will be higher than at normal input voltage and Tref must be limited to absolute max +105C. The absolute maximum continuous input voltage is 75 Vdc. Turn-off Input Voltage The DC/DC converters monitor the input voltage and will turn on and turn off at predetermined levels. The minimum hysteresis between turn on and turn off input voltage is 1V. Remote Control (RC) The products are fitted with a remote control function referenced to the primary negative input connection (- In). The RC function allows the converter to be turned on/off by an external device like a semiconductor or mechanical switch. The RC pin has an internal pull up resistor to + In. The maximum required sink current is 1 mA. When the RC pin is left open, the voltage generated on the RC pin varies between 9V and 17V depending on input voltage. The module has a "positive logic" remote control, i.e. the converter will turn on when the input voltage is applied with the RC pin open. Turn off is achieved by connecting the RC pin to the In. To ensure safe turn off the voltage difference between RC pin and the - In pin shall be less than 1V. The converter will restart automatically when this connection is opened. See Design Note 021 for detailed information. Input and Output Impedance The impedance of both the input source and the load will interact with the impedance of the DC/DC converter. It is important that the input source has low characteristic impedance. The converters are designed for stable operation without external capacitors connected to the input or output. The performance in some applications can be enhanced by addition of external capacitance as described under External Decoupling Capacitors. If the input voltage source contains significant inductance, the addition of a 100 F capacitor across the input of the converter will ensure stable operation. The capacitor is not required when powering the DC/DC converter from an input source with an inductance below 10 H. External Decoupling Capacitors When powering loads with significant dynamic current Rev 10 Reference EN/LZT 146 393 R1E September 2008 C (c) Ericsson Power Modules AB requirements, the voltage regulation at the point of load can be improved by addition of decoupling capacitors at the load. The most effective technique is to locate low ESR ceramic and electrolytic capacitors as close to the load as possible, using several parallel capacitors to lower the effective ESR. The ceramic capacitors will handle high-frequency dynamic load changes while the electrolytic capacitors are used to handle low frequency dynamic load changes. Ceramic capacitors will also reduce any high frequency noise at the load. It is equally important to use low resistance and low inductance PCB layouts and cabling. External decoupling capacitors will become part of the control loop of the DC/DC converter and may affect the stability margins. As a "rule of thumb", 100 F/A of output current can be added without any additional analysis. The ESR of the capacitors is a very important parameter. Power Modules guarantee stable operation with a verified ESR value of >10 m across the output connections. For further information please contact your local Ericsson Power Modules representative. E Ericsson Internal PRODUCT SPECIFICATION Prepared (also subject responsible if other) 3/1301-BMR 603Technical 1203/1 UenSpecification MICMALE Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) 3 (5) No. Checked Date Rev 11 Reference EN/LZT 146 393 R1E September 2008 (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W C (c) Ericsson Power Modules AB Operating information continued Parallel Operation Two or more converters may be paralleled for increased power capability. No external current sharing circuits are required. The direct paralleling is possible thanks to high initial output voltage accuracy and decreasing temperature characteristics of the output voltages. Over Temperature Protection (OTP) The converters are protected from thermal overload by an internal over temperature shutdown circuit. When Tref as defined in thermal consideration section exceeds 115C the converter will shut down. The DC/DC converter will make continuous attempts to start up (nonlatching mode) and resume normal operation automatically when the temperature has dropped >10C below the temperature threshold. Over Voltage Protection (OVP) The converters have output over voltage protection that will shut down the converter in over voltage conditions. The converter will make continuous attempts to start up (nonlatching mode) and resume normal operation automatically after removal of the over voltage condition. Over Load Protection (OLP) The converters include load limiting circuitry for protection at continuous overload. This function is implemented on the primary side of the module. The output voltages will decrease towards zero if the total output power (sum of loads on all three outputs) exceeds the maximum allowed output power. Note that output 1 (78V) is not short circuit protected in case of low loads on outputs 2 and 3. The load distribution should be designed for the maximum output short circuit current specified. Thermal Consideration General The converters are designed to operate in different thermal environments and sufficient cooling must be provided to ensure reliable operation. Cooling is achieved mainly by conduction, from the pins to the host board, and convection, which is dependant on the airflow across the converter. Increased airflow enhances the cooling of the converter. The Output Current Derating graph found in the Output section for each model provides the available output current vs. ambient air temperature and air velocity at Vin = 53 V. The DC/DC converter is tested on a 254 x 254 mm, 35 m (1 oz), 8-layer test board mounted vertically in a wind tunnel with a cross-section of 305 x 305 mm. Proper cooling of the DC/DC converter can be verified by measuring case temperature close to the reference point.at positions P1, P2 and P3. The temperature at these positions should not exceed the max values provided in the table below. Note that the max value is the absolute maximum rating (non destruction) and that the electrical Output data is guaranteed up to Tref +95C. See Design Note 019 for further information. Position Device Designation max value P1 MOSFET T1 120 C P2 Diode D4 110 C P3 Diode D5 110 C E Ericsson Internal PRODUCT SPECIFICATION Prepared (also subject responsible if other) 3/1301-BMR 603Technical 1203/1 UenSpecification MICMALE Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie Johansson) 4 (5) No. Checked Date Rev (MICANWO) 2008-09-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Thermal Consideration continued Reference EN/LZT 146 393 R1E September 2008 C (c) Ericsson Power Modules AB Connections 1 Definition of reference temperature (Tref) 24 The reference temperature is used to monitor the temperature limits of the product. Temperatures above maximum Tref are not allowed and may cause degradation or permanent damage to the product. Tref is also used to define the temperature range for normal operating conditions. Tref is defined by the design and used to guarantee safety margins, proper operation and high reliability of the module. 13 12 Pin 1 Designation GND Function Ground 2 GND Ground 3 -IN Input voltage -48V 4 -IN Input voltage -48V 5 RC Remote control 6 GND Ground 7 GND Ground 8 N/C Not connected 9 Return1 Output 78V return 10 Out1 Output +78V 11 GND Ground 12 GND Ground 13 GND Ground 14 GND Ground 15 Out2 Output --52V 16 Out2 Output --52V 17 N/C Not connected 18 Out3 Output --33V 19 Out3 Output --33V 20 N/C Not connected 21 N/C Not connected 22 GND Ground 23 GND Ground 24 GND Ground 12 E Ericsson Internal PRODUCT SPEC. MECHANICAL Prepared (also subject responsible if other) 4/1301-BMR 603Technical 1203 Uen Specification MICKAOV Approved BMR 603 1203/1 SEC/D/T (Julia You) 1 (3) No. Checked Date See 1 2008-07-10 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Mechanical Information (assembly information, see next page) Rev Reference EN/LZT 146 393 R1E September 2008 C (c) Ericsson Power Modules AB 13 E Ericsson Internal PRODUCT SPEC. MECHANICAL Prepared (also subject responsible if other) 4/1301-BMR 603Technical 1203 Uen Specification MICKAOV Approved BMR 603 1203/1 SEC/D/T (Julia You) Checked Date See 1 2008-07-10 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Assembly Information 2 (3) No. Rev Reference EN/LZT 146 393 R1E September 2008 C (c) Ericsson Power Modules AB 14 E Ericsson Internal PROD. SPECIFICATION MECHANICAL Prepared (also subject responsible if other) 1 (4) No. 15 5/1301-BMR 603Technical 1203 Uen Specification MICKAOV Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie J) Checked Date See 1 2008-06-05 Rev Reference EN/LZT 146 393 R1E September 2008 B DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W (c) Ericsson Power Modules AB Soldering Information The product is intended for convection reflow or vapor phase reflow in Pb-free reflow processes. The reflow profile should be optimised to avoid excessive heating of the product. It is recommended to have a sufficiently extended preheat time to ensure an even temperature across the host PCB and to minimize the time in reflow. Temperature Solder bump Profile 60-90 s 170C to 180C 30-60 s 221C to 225C Time A no-clean flux is recommended to avoid entrapment of cleaning fluids in cavities inside the product or between the product and the host board, since cleaning residues may affect long time reliability and isolation voltage. Reflow process specifications1 SnPb eutectic Average ramp-up rate N/A 3C/s max TL N/A +221C N/A 30 s Minimum pin temperature TPIN N/A +235C Peak product temperature TPRODUCT N/A +260C N/A 6C/s max Typical solder melting (liquidus) temperature Minimum reflow time above TL Average ramp-down rate 1 Pb-free Maximum time 25C to peak N/A 8 minutes Note: for mixed SnPb / Pb-free soldering, special recommendations apply Reflow profile for mixed soldering (pin temperature = solder joint temperature) Thermocoupler Attachment Component outline Top of PCB at pin 1 for measurement of maximum product temperature, TPRODUCT 1 Pin 6/7 or pin 18/19 for measurement of minimum pin (solder joint) temperature, TPIN (attach sensors as close as possible to actual solder joint) Temperatur e TPRODU CT m axi mum TPIN minimum P in profi le TL 12 Prod uct profile Time in reflow Time in preheat / soak zone Ti me 25C to p eak T ime General reflow profile (min pin and max product temperature) Mixed Solder Process Recommendations When using products with Pb-free solder bumps with SnPb paste on the host board, and thereby mixing SnPb with Pbfree solder, and reflowing at SnPb process temperatures (backwards compatibility), special recommendations apply: An extended preheat time between +170C and +180C for 60 to 90s and a pin reflow temperature (TPIN) between +220C and +225C for 30 to 60 s is recommended. Ramp-up, rampdown and time limitations should be according to Pb-free reflow process specifications. The extended preheat time and soak at reflow temperature will minimize temperature gradients and maximize the wetting and solder mixing in the final solder joints. The use of nitrogen reflow atmosphere will further improve the solder joint quality. 13 Pin Temperature Recommendations Pin number 6/7 and 18/19 are chosen as reference locations for the minimum pin temperature recommendations since these will likely be the coolest solder joints during reflow Pb-free Solder Processes For Pb-free solder processes, a pin temperature (TPIN) in excess of the solder melting temperature (TL, +217 to +221 C for SnAgCu solder alloys) for more than 30 seconds, and a peak temperature of +235C on all solder joints is recommended to ensure a reliable solder joint. Maximum Product Temperature Requirements Top of the product PCB near pin 1 is chosen as reference location for the maximum (peak) allowed product temperature (TPRODUCT), since this will likely be the warmest part of the product during the reflow process. Pb-free Solder Processes For Pb-free solder processes, the product is qualified for MSL 3 according to IPC/JEDEC standard J-STD-020C. During reflow, TPRODUCT must not exceed +260 C at any time. E Ericsson Internal PROD. SPECIFICATION MECHANICAL Prepared (also subject responsible if other) 5/1301-BMR 603Technical 1203 Uen Specification MICKAOV Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie J) 2 (4) No. Checked Date See 1 2008-06-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Rev 16 Reference EN/LZT 146 393 R1E September 2008 B (c) Ericsson Power Modules AB Surface Mount Assembly and Repair Delivery Package Information The solder bumps of the product require particular care during assembly since the solder bumps are hidden between the host board and the product's PCB. Special procedures are required for successful rework of these products. The surface mount version of the product is delivered in antistatic injection molded trays (Jedec design guide 4.10D standard). Tray Specifications Assembly Automatic pick and place equipment should be used to mount the product on the host board. The use of a vision system, utilizing the fiducials on the bottom side of the product, will ensure adequate accuracy. Manual mounting of solder bump products is not recommended. Note that the actual position of the pick up surface may vary between variants within the product program and is not necessarily in the center of the product outline. If necessary, it is recommended to fine tune the solder print aperture size to optimize the amount of deposited solder with consideration to screen thickness and solder print capability. Repair For a successful repair (removal and replacement) of a solder bump product, a dedicated rework system should be used. The rework system should preferably utilize a bottom side heater and a dedicated hot air nozzle to heat the solder bumps to reflow temperature. The product is an open frame design with a pick up surface on a large central component. This pick up surface can not be used for removal with a vacuum nozzle since the component solder joints may have melted during the removal reflow. In order not to damage the product and nearby components during removal and replacement with a new product, it is recommended to use a double wall design of the hot air nozzle to direct the air flow only to the edges of the product, see `Assembly Information' in the mechanical drawing. Dry Pack Information Products intended for Pb-free reflow processes are delivered in standard moisture barrier bags according to IPC/JEDEC standard J-STD-033 (Handling, packing, shipping and use of moisture/reflow sensitivity surface mount devices). The SnPb option of this product is also delivered in dry packing. Using products in high temperature Pb-free soldering processes requires dry pack storage and handling. In case the products have been stored in an uncontrolled environment and no longer can be considered dry, the modules must be baked according to J-STD-033. Material Antistatic PPE Surface resistance Tray capacity 105 < Ohm/square < 1012 The trays can be baked at maximum 125C for maximum 48 hours 10 products / tray Tray thickness 12.19 mm [0.480 inch] Tray weight 115 g empty, max 365 g full Baking E Ericsson Internal PROD. SPECIFICATION MECHANICAL Prepared (also subject responsible if other) 3 (4) No. 5/1301-BMR 603Technical 1203 Uen Specification MICKAOV Approved BMR 603 1203/1 EAB/FJB/GKF (Natalie J) Checked Date See 1 2008-06-05 DC/DC converters, Input 40-72 V, Output 78/-52/-33 V/32W Rev 17 Reference EN/LZT 146 393 R1E September 2008 B (c) Ericsson Power Modules AB Product Qualification Specification Characteristics External visual inspection IPC-A-610 Change of temperature (Temperature cycling) IEC 60068-2-14 Na Temperature range Number of cycles Dwell/transfer time -40 to +100C 1000 15 min/0-1 min Cold (in operation) IEC 60068-2-1 Ad Temperature TA Duration -45C 72 h Damp heat IEC 60068-2-67 Cy Temperature Humidity Duration +85C 85 % RH 1000 hours Dry heat IEC 60068-2-2 Bd Temperature Duration +125C 1000 h Electrostatic discharge susceptibility IEC 61340-3-1, JESD 22-A114 IEC 61340-3-2, JESD 22-A115 Human body model (HBM) Machine Model (MM) Class 2, 2000 V Class 3, 200 V Immersion in cleaning solvents IEC 60068-2-45 XA Method 2 Water Glycol ether Isopropanol +55C +35C +35C Mechanical shock IEC 60068-2-27 Ea Peak acceleration Duration 100 g 6 ms Moisture reflow sensitivity 1 J-STD-020C level 1 (SnPb-eutectic) level 3 (Pb Free) 225C 260C Operational life test MIL-STD-202G method 108A Duration 1000 h Resistance to soldering heat 2 IEC 60068-2-20 Tb Method 1A Solder temperature Duration 270C 10-13 s Robustness of terminations IEC 60068-2-21 Test Ua1 IEC 60068-2-21 Test Ue1 Through hole mount products Surface mount products All leads All leads Solderability IEC 60068-2-58 test Td 1 Preconditioning Temperature, SnPb Eutectic Temperature, Pb-free 150C dry bake 16 h 215C 235C IEC 60068-2-20 test Ta 2 Preconditioning Temperature, SnPb Eutectic Temperature, Pb-free Steam ageing 235C 245C IEC 60068-2-64 Fh, method 1 Frequency Spectral density Duration 10 to 500 Hz 0.07 g2/Hz 10 min in each perpendicular direction Vibration, broad band random Note 1: Only for products intended for reflow soldering (surface mount products) Note 2: Only for products intended for wave soldering (hole mounted products)