STANDARD THICK FILM CHIP RESISTORS ORDERIN G_Thesetwo pages contain key information for ordering standard grade thick film chip resistors. The termination styles and chip sizes are identified below. When you place an order, please INFORMATION specify the part number, packaging, and any special requirements. The Part Numbering System on the facing page describes how to correctly specify the part number for your chip. MIL-R-55342 chips are presented on pages 16 and 17. Special application thick film chips untrimmed, Kelvin, and jumpers - are presented on page 11. TERMINATIONS & SIZES STYLE CP TERMINATION STYLE AP TERMINATION STYLE DP TERMINATION STYLE EP TERMINATION WRAPAROUND GOLD WIRE BONDABLE METALLIZED BOTTOM ONE SIDE WRAPAROUND @ DIMENSIONS IN INCHES THICK FILM SIZE CODE TABLE @ DIMENSIONS IN mm (1 mm = .03937 inch) CTUAL size TOP BOTTOM MAXIMUM MAXIMUM A SIZE CODE LENGTH WiDTH THICKNESS TERMINATION TERMINATION POWER VOLTAGE A B c D E (mW) (volts) 0302 030 18% 020 +83 012 - 017 004 - .015 .006 - .015 35 15 76 748 51 8 30-43 10-38 15 - 38 0402 040 + 333 020 733 .015 - 022 .005 - .015 .008 - .016 50 30 OTHER SIZES AVAILABLE 10% 0 E 51 SE. 56 13 - 38 20-44 035 23 035 33 .015 - 022 .004 - .015 .008 - .016 50 25 0403 . 0404 8c e 8g oe 38- 56 10 - .38 20-44 0703 i oO 4002 . 0502 050 2883 025 7008 015 - .022 .004 - .015 .007 - .020 60 40 64 BE Ee 1G. 38 18-5 1507 050 +835 040 708 015 - .022 005 - .015 007 - .020 125 40 3818 a 0504 = 002 x 005 : | A x - x CHECK WITH FACTORY FOR tor of 102 "38 3E- 56 13 - 38 18-51 FULL DETAILS no 0505 ( + O02 050 2932 015 - 022 005 - .015 .007 - .020 125 40 ter 8 12700 Sf. 56 13-38 18-51 a 0705 075 18% .050 2995 .015 - 022 .010 - 020 .010 - .025 200 50 191 18 127 04 38 - 56 .25 - 51 .25 - .64 o 1005 100 568 050 388 015 - 022 .010 - .020 .010 - .025 250 75 254 7h 127-38 38- 56 25-51 25 - 64 Po 1206 125 +58 065 195 .015 - .022 .010 - 020 .010 - .030 250 100 318 138 165 33 38 - 56 25-51 25 - .76 150 108 050 +05 015 - .022 .010 - .020 .010 - .025 330 125 1505 381 0 1.27 ie 38 - 56 25-51 25 - 64 OB . 13 " . . oO 1010 400. *3h2 100 2% 015 - 022 010 - 025 010 - .025 600 75 254 % 254 +13 .38 - 56 25 - 64 .25 - 64 co 2208 225 Ore O75 2938 .028 - .032 .010 - .020 .010 - .030 750 175 572 +33 191 % 64-81 25-51 25 -.76 Cl 2010 200 2 100. +888 025 - .032 .009 - .029 .008 - .029 1000 150 5.08 +3 2.54 +23 64-81 23-74 23-74 | 2512 250 18% 125 +008 025 - .032 .009 - .029 .008 - .029 2000 200 636 78 a1 % 64- 81 23-74 23-74 Notes Size 0705 is usually the most economical. Its use is recommended except where its size is excessive or where power and/or voltage ratings may be exceeded. Size 0504 is available in Styles CP and EP only. Specifications subject to change without notice. 12 State of the Art, Inc. TOLL FREE 1-800-458-3401 FAX 814-355-2714SYSTEM SYEMPles PACKAGING To order standard grade or high reliability thick film chip resistors, follow the part numbering format below. The part number S0504CPX159J specifies a standard production .050 x .040 inch, 15 ohm + 5% resistor with pretinned nickel barrier wraparound terminations. S$ 0504 CP X 150 J : _ |. SPECIAL TERMINATION i : tot : G: Gold PS: Palladiun/silver CH np Serb FEE Do Gold over Nickel PG: Platinumvgold i ' TCR CERTIFICATION : ' 10:+100 ppm 20:4+200 ppm 30: +300 ppm : . TOLERANCE 1 D:0.5% F:1% G:2% J:5%. RESISTANCE VALUE intrimmed resistor (see page. ") TERMINATION STYLE AP: Top-side termination with Bottom Isolated etal EP: Single Wraparound with Bottom Metaltized SIZE CODE See Physical and Mechanical Data PREFIX Cs Commercial/industrial (please consult factory) ; Standard Production =. 6-02: High Reliability/Custom Screening Variations of the example part number above are: SO504CP 150JPS same as above. except untinned palladium/silver SO504CPXU 150M same as above. except untrimmed, 20% tolerance S0504CPX 150J20 same as above, except TCR certified to 200 ppm {f in doubt about the proper code, or if additional information must be included, use plain language. Standard grade individual lot quantities are bulk packed in anti-static self-sealing bags. High reliability (H) resistors are packed in chip tray carriers (waffle packs). Tape and reel packaging to EIA-RS481 can be specified on a standard 7 inch reel or an optional 13 inch reel for the following sizes: m 8 mm tape 0504, 0505, 0705, 1005, 1206, 1010 m 12mm tape 1505, 2208. 2010, 2512 Each package carries a non-corrosive label indicating the quantity, part number, lot number, date code, resistance value, and tolerance. State of the Art, tne. TOLL FREE 7-006-058-2607 FAX 814-285-2774 13