Data SheetData Sheet
Date: September 2006
EPCOS AG 2006. Reproduction, publication and dissemination of this data sheet and the
information contained therein without EPCOS’ prior express consent is prohibited.
Ferrites and accessories
EP 13
Core and accessories
Series/Type: B65843A, B65844
209/06
Please read Cautions and warnings and
Important notes at the end of this document.
To IEC 61596
For transformers featuring high inductance
and low overall height
For power applications
Delivery mode: sets
Magnetic characteristics (per set)
Σ l/A= 1.24 mm
–1
le= 24.2 mm
Ae= 19.5 mm2
Amin = 14.9 mm2
Ve= 472 mm3
Approx. weight 4.5 g/set
Gapped
Material AL value
nH
s
approx.
mm
µeOrdering code
T38 63 ±3% 0.39 62 B65843A0063A038
100 ±3% 0.24 99 B65843A0100A038
160 ±4% 0.15 158 B65843A0160B038
200 ±4% 0.12 198 B65843A0200B038
250 ±5% 0.10 247 B65843A0250J038
315 ±6% 0.08 311 B65843A0315C038
400 ±7% 0.06 395 B65843A0400E038
T57 63 ±3% 0.38 62 B65843A0063A057
100 ±3% 0.24 99 B65843A0100A057
160 ±4% 0.15 158 B65843A0160B057
200 ±4% 0.12 198 B65843A0200B057
250 ±5% 0.09 247 B65843A0250J057
315 ±6% 0.07 311 B65843A0315C057
400 ±7% 0.06 395 B65843A0400E057
T66 63 ±3% 0.39 62 B65843A0063A066
100 ±3% 0.24 99 B65843A0100A066
160 ±4% 0.15 158 B65843A0160B066
200 ±4% 0.12 198 B65843A0200B066
250 ±5% 0.10 247 B65843A0250J066
315 ±6% 0.08 311 B65843A0315C066
400 ±7% 0.06 395 B65843A0400E066
FEP0017-A
5,5
2,4±0,1
9 0,4
_
9,7+0,6
4,5 0,3
_
13 0,3
_
9+0,4
12,8
_
0,6
)
s
gapped (one-sided)
)
B65843ACore
EP 13
309/06
Please read Cautions and warnings and
Important notes at the end of this document.
Gapped
Ungapped
Material AL value
nH
s
approx.
mm
µeOrdering code
N45 63 ±3% 0.38 62 B65843A0063A045
100 ±3% 0.24 99 B65843A0100A045
160 ±4% 0.15 158 B65843A0160B045
200 ±4% 0.12 198 B65843A0200B045
250 ±5% 0.09 247 B65843A0250J045
315 ±6% 0.07 311 B65843A0315C045
400 ±7% 0.05 395 B65843A0400E045
N87 63 ±3% 0.37 62 B65843A0063A087
100 ±3% 0.23 99 B65843A0100A087
160 ±4% 0.14 158 B65843A0160B087
200 ±4% 0.11 198 B65843A0200B087
250 ±5% 0.09 247 B65843A0250J087
315 ±6% 0.07 311 B65843A0315C087
400 ±7% 0.05 395 B65843A0400E087
Material AL value
nH
µePV
W/set
Ordering code
N45 2400 +30/–20% 2370 B65843A0000R045
T571) 2500 +30/–20% 2470 B65843A0000R057
N30 2800 +30/–20% 2765 B65843A0000R030
T65 4000 +30/–20% 3950 B65843A0000R065
T38 7000 +40/–30% 6910 B65843A0000Y038
T66 8500 +40/–30% 8400 B65843A0000Y066
N87 1600 +30/–20% 1580 < 0.18 (200 mT, 100 kHz, 100 °C) B65843A0000R087
1) Preliminary data
B65843ACore
EP 13
409/06
Please read Cautions and warnings and
Important notes at the end of this document.
Coil former, squared pins
Material: GFR thermosetting plastic (UL 94 V-0, insulation class to IEC 60085:
H max. operating temperature 180 °C), color code black
Sumikon PM 9630 ® [E41429 (M)], SUMITOMO BAKELITE CO LTD
Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s
Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s
Winding: see Data Book 2007, chapter “Processing notes, 2.1”
Sections AN
mm2
lN
mm
AR value
µΩ
Terminals Ordering code
114.3 23.8 57.1 10 B65844W1010D001
FEP0056-U-E
0.6
0.45
View in mounting direction
Ground ø1.3+0.2
4.8±0.3
ø1+0.2
1.5
Hole arrangement
2.54
9.5
4.6+0.1
10.2
14.8
15.9
13.3
0.6
ø5.75
Marking of pin row
including pin 1
0.1
_
0.2
_
0.2
_
0.1
_
8.9 0.1
_
B65844Accessories
EP 13
509/06
Please read Cautions and warnings and
Important notes at the end of this document.
Coil former with closed center flange for high-voltage applications
Material: GFR thermosetting plastic (UL 94 V-0, insulation class to IEC 60085:
H max. operating temperature 180 °C), color code black
Sumikon PM 9630 ® [E41429 (M)], SUMITOMO BAKELITE CO LTD
Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s
Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s
Winding: see Data Book 2007, chapter “Processing notes, 2.1”
Squared pins.
Sections AN
mm2
lN
mm
AR value
µΩ
Terminals Ordering code
213.9 23.8 58.9 10 B65844X1010D002
FEP0019-D-E
0.6
0.45
View in mounting direction
Ground ø1.3+0.2
4.8±0.3
ø1+0.2
1.5
Hole arrangement
2.54
9.5
4.6+0.1
10.2
14.8
15.9
13.3
0.6
ø5.75
0.45
Marking of pin row
including pin 1
0.1
0.2
_
0.2
_
0.1
_
8.9 0.1
_
_
B65844Accessories
EP 13
609/06
Please read Cautions and warnings and
Important notes at the end of this document.
Mounting assembly
The set comprises a yoke and a clamp
Yoke
Made of nickel silver (0.4 mm) with ground terminal (tinned)
Clamp
Spring clamp, made of nickel silver (0.4 mm)
Yoke Clamp
Ordering code
Complete mounting assembly B65844A2000X000
FEP0020-F
11,7
4
13
2,6
16,5
7,5
1 x 0,4
FEP0021-G
12,7
14 7,5
B65844Accessories
EP 13
709/06
Ferrites and accessories
Cautions and warnings
Mechanical stress and mounting
Ferrite cores have to meet mechanical requirements during assembling and for a growing number
of applications. Since ferrites are ceramic materials one has to be aware of the special behavior
under mechanical load.
As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing
or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads
can cause cracks or failure of the ferrite cores.
For detailed information see Data Book 2007, chapter “General – Definitions, 8.1”.
Effects of core combination on AL value
Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent
that the initial permeability is dependent on the stress state of the core. The higher the stresses are
in the core, the lower is the value for the initial permeability. Thus the embedding medium should
have the greatest possible elasticity.
For detailed information see Data Book 2007, chapter “General – Definitions, 8.2”.
Heating up
Ferrites can run hot during operation at higher flux densities and higher frequencies.
NiZn-materials
The magnetic properties of NiZn-materials can change irreversible in high magnetic fields.
Processing notes
The start of the winding process should be soft. Else the flanges may be destroid.
To strong winding forces may blast the flanges or squeeze the tube that the cores can no more
be mount.
To long soldering time at high temperature (>300 °C) may effect coplanarity or pin arrangement.
Not following the processing notes for soldering of the J-leg terminals may cause solderability
problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation
of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”.
The dimensions of the hole arrangement have fixed values and should be understood as a
recommendation for drilling the printed circuit board. For dimensioning the pins, the group of
holes can only be seen under certain conditions, as they fit into the given hole arrangement. To
avoid problems when mounting the transformer, the manufacturing tolerances for positioning the
customers’ drilling process must be considered by increasing the hole diameter.
809/06
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic components
or failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of a passive electronic component could endanger human life or health
(e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of
suitable design of the customer application or other action taken by the customer (e.g.
installation of protective circuitry or redundancy) that no injury or damage is sustained by third
parties in the event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, EPCOS-JONES, Baoke, Alu-X, CeraDiode, CSSP, MLSC,
PhaseCap, PhaseMod, SIFI, SIFERRIT, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K,
UltraCap, WindCap are trademarks registered or pending in Europe and in other countries.
Further information will be found on the Internet at www.epcos.com/trademarks.