C&K 3 Series Thumbwheel Switches Features/Benefits * Most complete product offering in the industry * Spacers available to fit most panel cutouts * Front or rear mounting options * Illuminated models available Typical Applications * Test & measurement equipment * Industrial equipment * Computer devices Specifications Materials CONTACT RATING: CARRY: 1 AMP continuous. SWITCH: 100 mA max. OPERATING VOLTAGE: 50 mV to 28 V DC or 120 V AC. ELECTRICAL LIFE: 100,000 actuations. CONTACT RESISTANCE: Below 100 m typ. initial @ 2-4 V DC, 100 mA. INSULATION RESISTANCE: 109 min. DIELECTRIC STRENGTH: 500 Vrms min. @ sea level between common terminal and any output. OPERATING TEMPERATURE: -10C to 65C. HOUSING: ABS plastic. THUMBWHEEL: ABS plastic. ROTOR CONTACTS: Precious metal on copper alloy. STATOR CONTACTS: Hard gold over nickel over copper on epoxy fiberglass. NOTE: Specifications and materials listed above are for switches with standard options For information on specific and custom switches, consult Customer Service Center. Thumbwheel & Pushwheel Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages M-9 thru M-12. For additional options not shown in catalog, consult Customer Service Center. Consult factory for illumination availability. Series 3 (STD.) Thumbwheel switch Number of Sections 0 Switch section 1 1 Switch section 2 2 Switch sections 3 3 Switch sections 4 4 Switch sections 5 5 Switch sections 6 6 Switch sections 7 7 Switch sections 8 8 Switch sections 9 More than 8 switch sections Function Code 11 Decimal, SP, 10 position 14 Resistor decade 21 BCD, 10 position 23 Complement of BCD, 10 position 27 BCD, 10 position 31 BCD, 10 position 71 BCH, 16 position Mounting Style 00 Snap-in, front mount 09 Snap-in, front mount* 10 Rear mount 19 Rear mount* 20 Rear mount 29 Rear mount* Terminations 0 (STD.) Type 0 1 Type 1, extended type 0 3 Type 0 with solder pins B Type 6 with solder pins Color/Marking/Stops 0 (STD.) Matte black body, gloss black wheel, Seal white marking 0 (STD.) No seal 1 Sealed contacts 2 Dust lens 3 Sealed contacts & dust lens M *X9 mounting styles must be ordered with `0' number of sections. Dimensions are shown: IN (mm) Dimensions subject to change M-8 www.ittcannon.com C&K 3 Series Thumbwheel Switches SERIES 3 (STD.) THUMBWHEEL SWITCHES NUMBER OF SECTIONS 0 Switch section only, no assembly. Blank bodies are considered sections; endplates are not sections. Must be ordered with 09 or 19 mounting style options, see pages M-10 and M-11. 1-8 Number of switch sections in assembly, includes endplates. 9 More than 8 switch sections, specify on CONFIGURATION FORM, page M-15 and consult Customer Service Center. Thumbwheel & Pushwheel NOTE: Endplates and blank sections available separately, see pages M-13 and M-14. FUNCTION CODE 11 DECIMAL-1 POLE; 10 POSITION 14 RESISTOR DECADE; 1-2-2-2-2 CODE (RESISTORS NOT SUPPLIED) 21 BCD 1-2-4-8; 10 POSITION M Available Terminations: 0, 1, 3 Available Terminations: 1 Available Terminations: 0, 1, 3 See fig. 1, page M-12. See fig. 1, page M-12. See fig. 1, page M-12. NOTE: For terminal location diagram, see page M-12. Third Angle Projection Dimensions are shown: IN (mm) Dimensions subject to change M-9 www.ittcannon.com C&K 3 Series Thumbwheel Switches FUNCTION CODE 23 COMPLEMENT OF BCD 1-2-4-8; 10 POSITION 27 31 BCD 1-2-4-8; 10 POSITION BCD 1-2-4-8; 10 POSITION Available Terminations: 0, 1, 3 Available Terminations: B Available Terminations: 0, 1, 3 See fig. 1, page M-12. See fig. 2, page M-12. See fig. 1, page M-12. 71 BINARY CODED HEXADECIMAL, 16 POSITION Available Terminations: 0, 1, 3 See fig. 1, page M-12. NOTE: For terminal location diagram, see page M-12. MOUNTING STYLE Thumbwheel & Pushwheel Type 0 Snap-In Front Mount PANEL MOUNTING MOUNTING STYLE 00 DIM. `A' (.315 x N) + .326 (8,00 x N) + (8,28) N = Number of sections. Recommended panel thickness: 0.46-.125 (1,16-3,18) 00 SWITCH ASSEMBLY W/ ENDPLATES-.315 (8,00) SECTION PITCH M N = Number of sections. 09 SWITCH SECTION ONLY-UNASSEMBLED WITHOUT ENDPLATES OR SPACERS (Must be ordered with number of sections option "0", see Page M-9.) NOTE: Endplates, blank sections, spacers and assembly hardware available separately, see pages M-13 and M-14. Third Angle Projection Dimensions are shown: IN (mm) Dimensions subject to change M-10 www.ittcannon.com C&K 3 Series Thumbwheel Switches MOUNTING STYLE Type 1 Rear Mount PANEL MOUNTING MOUNTING STYLE DIM. `A' DIM. `B' (.350 x N) + .340 (8,89 x N) + (8,64) (.350 x N) + .560 (8,89 x N) + (14,22) Mtg. Holes 10 N = Number of sections. Recommended panel thickness: 0.46-.125 (1,16-3,18) 10 SWITCH ASSEMBLY W/ ENDPLATES-.350 (8,89) SECTION PITCH N = Number of sections. 19 SWITCH SECTION ONLY-UNASSEMBLED WITHOUT ENDPLATES OR SPACERS (Must be ordered with number of sections option "0", see Page M-9.) 20 SWITCH ASSEMBLY W/ ENDPLATES-.350 (8,89) SECTION PITCH N = Number of sections. 29 Thumbwheel & Pushwheel Type 2 Rear Mount SWITCH SECTION ONLY-UNASSEMBLED WITHOUT ENDPLATES OR SPACERS (Must be ordered with number of sections option "0", see Page M-9.) M Type 3 Snap1-in Front Mount 09 SWITCH SECTION ONLY-UNASSEMBLED WITHOUT ENDPLATES OR SPACERS (Must be ordered with number of sections option "0", see Page M-9.) NOTE: Endplates, blank sections, spacers and assembly hardware available separately, see pages M-13 and M-14. Third Angle Projection Dimensions are shown: IN (mm) Dimensions subject to change M-11 www.ittcannon.com C&K 3 Series Thumbwheel Switches TERMINATIONS 0 1 (STD.) TYPE 0 TYPE 1, EXTENDED TYPE 0 3 TYPE 0 WITH SOLDER PINS Signal traces cut except for common(s). 9 ANY COMBINATION OF TERMINATION CONFIGURATIONS OR SPECIAL TERMINATIONS. B TYPE 6 WITH SOLDER PINS Specify on configuration form, page M-15 and consult Customer Service Center. PC Board 1/32" (0,79) thick. Thumbwheel & Pushwheel NOTE: All terminal holes shown may not be present for all function codes, consult Customer Service Center. Terminal connector available for termination options 0 & 1, see page M-14. Terminal Location Numbers FIG. 1 FIG. 2 NOTE: See function codes, pages M-9 and M-10, for signal locations. COLOR/MARKING/STOPS 0 (STD.) MATTE BLACK HOUSING (Gloss black wheel with white characters; no stops.) NOTE: Stop pins are available separately, see page M-14. SEAL M 0 1 (STD.) UNSEALED SWITCHING CONTACTS. SEALED SWITCHING CONTACTS. (Sealing is by means of an o-ring rotary seal and a cured-in-place elastomer gasket. Switching contact area is protected from moisture, oil, and airborne contaminants.) 2 DUST LENS. (Protects the character face of the wheel from abrasion and dirt). 3 SEALED SWITCHING CONTACTS AND DUST LENS Dust Lens Third Angle Projection Dimensions are shown: IN (mm) Dimensions subject to change M-12 www.ittcannon.com C&K 3 Series Thumbwheel Switches AVAILABLE HARDWARE Blank sections, Front mount, Type 0 & 3, .315 THK. Blank sections, Type 0 & 3, .315 THK. Blank sections, Rear mount, Type 1, .350 THK. 4006 4008 PART NO. PART NO. PART NO. 413602000 W/RIB-BLACK 413609000 W/RIB-GRAY 413502000 PLAIN-BLACK 413509000 PLAIN-GRAY 400602000 W/RIB-BLACK 400609000 W/RIB-GRAY 400502000 W/RIB & W/OUT SPRINGS-BLACK 400509000 W/RIB & W/OUT SPRINGS-GRAY 400702000 PLAIN & W/OUT SPRINGS-BLACK 400709000 PLAIN & W/OUT SPRINGS-GRAY 400802000 PLAIN-BLACK 400809000 PLAIN-GRAY Blank sections, Rear mount, Type 2, .350 THK. End plates, Front mount, Type 0 End plates, Rear mount, Type 1 4733 PART NO. 473402000 W/RIB-BLACK 473409000 W/RIB-GRAY PART NO. 473302000 PLAIN-BLACK 473309000 PLAIN-GRAY 413402000 BLACK 413409000 GRAY End plates, Rear mount, Type 2 Spacers, Front mount, Type 0 & 3, .078 THK. (Makes section pitch 10mm) PART NO. Two required for complete assembly. 400402000 BLACK 400409000 GRAY Two required for complete assembly. Stop pins Thumbwheel & Pushwheel 4734 M PART NO. 473202000 BLACK 473209000 GRAY Two required for complete assembly. PART NO. PART NO. 410802000 BLACK 410809000 GRAY 402900000 Dimensions are shown: IN (mm) Dimensions subject to change M-13 www.ittcannon.com C&K 3 Series Thumbwheel Switches AVAILABLE HARDWARE Terminal connector 605A00000 605A02000 PART NO. 605A00000 PC 605A02000 SOLDER LUG Fits 0 & 1 terminations only. Screws for field assembly of thumbwheel switches (2 screws needed per assembly + 403500000 nuts) Thumbwheel & Pushwheel NUMBER OF SECTIONS IN ASSEMBLY FRONT MOUNTING REAR MOUNTING SCREW PART NUMBER (0-80 UNF THD. SIZE) MTG. STYLE - 00 MTG. STYLE - 10 412700000 1-2 1-2 412701000 3-4 3 412702000 5-7 4-6 412703000 8-10 7-9 412704000 11-13 10-12 412705000 14-16 13-15 Nut Nut driver (For 403500000 nut) Two nuts required per assembly and screws. PART NO. PART NO. 403500000 406100652 M Dimensions are shown: IN (mm) Dimensions subject to change M-14 www.ittcannon.com C&K 3 Series Thumbwheel Switches C&K PART NUMBER Configuration Form GRAY SHADED AREAS TO BE FILLED IN BY CUSTOMER SERVICE. CATALOG PART NO. C&K PART NUMBER 3 ADDRESS TEL.# CUSTOMER PRINT REVISION: CUSTOMER CONTACT DATE DETAILS: ORIGINATED BY SALES REP. COMPANY NAME THUMBWHEEL SECTIONS NO. OF SEC. FUNCTION CODE - TERMINATIONS - COLOR/MARKING/STOPS/SEAL - ILLUMINATION DESCRIBE IN APPROPRIATE ROW ENTER OPTION CODES IN APPROPRIATE BOXES. FUNCTION CODES INCLUDE BLANK SECTIONS (SEE PAGES M-9 & M-10). 3 - - - 2 3 - - - 3 3 - - - 4 3 - - - 5 3 - - - 6 3 - - - 7 3 - - - 8 3 - - - 9 3 - - - 10 3 - - - 11 3 - - - QUALITY CONTROL INSTRUCTIONS Thumbwheel & Pushwheel 1 PRODUCTION APPROVAL DATE Q.C. APPROVAL DATE M REV. INITIALS DATE FOR SWITCHES WITH MORE THAN 11 SECTIONS, CONTINUE ON ADDITIONAL SHEETS. SPECIAL INSTRUCTIONS OR SPECIFICATIONS: SHEET _____ OF _____ Dimensions are shown: IN (mm) Dimensions subject to change M-15 www.ittcannon.com Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: C&K Components: 406100652 412707000 321110300 412703000 400402000 342210000