M-8
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
M
Thumbwheel & Pushwheel
Features/Benefits
•Most complete product offering in the industry
•Spacers available to fit most panel cutouts
•Front or rear mounting options
•Illuminated models available
Typical Applications
•Test & measurement equipment
•Industrial equipment
•Computer devices
Specifications
CONTACT RATING:
CARRY: 1 AMP continuous.
SWITCH: 100 mA max.
OPERATING VOLTAGE: 50 mV to 28 V DC or 120 V AC.
ELECTRICAL LIFE: 100,000 actuations.
CONTACT RESISTANCE: Below 100 m Ωtyp. initial @
2-4 V DC, 100 mA.
INSULATION RESISTANCE: 109Ωmin.
DIELECTRIC STRENGTH: 500 Vrms min. @ sea level
between common terminal and any output.
OPERATING TEMPERATURE: -10ºC to 65ºC.
Materials
HOUSING: ABS plastic.
THUMBWHEEL: ABS plastic.
ROTOR CONTACTS: Precious metal on copper alloy.
STATOR CONTACTS: Hard gold over nickel over copper
on epoxy fiberglass.
NOTE: Specifications and materials listed above are for switches with standard options
For information on specific and custom switches, consult Customer Service Center.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown and
described on pages M-9 thru M-12. For additional options not shown in catalog, consult Customer Service Center.
Consult factory for illumination availability.
Series
3(STD .) Thumbwheel switch
Number of Sections
0Switch section
11 Switch section
22 Switch sections
33 Switch sections
44 Switch sections
55 Switch sections
66 Switch sections
77 Switch sections
88 Switch sections
9More than 8
switch sections
Seal
0(STD.) No seal
1Sealed contacts
2Dust lens
3Sealed contacts & dust lens
Function Code
11 Decimal, SP,10 position
14 Resistor decade
21 BCD, 10 position
23 Complement of BCD, 10 position
27 BCD, 10 position
31 BCD, 10 position
71 BCH, 16 position
Terminations
0(STD .) Type 0
1Type 1, extended type 0
3Type 0 with solder pins
BType 6 with solder pins
Color/Marking/Stops
0(STD.) Matte black body,
gloss black wheel,
white marking
Mounting Style
00 Snap-in, front mount
09 Snap-in, front mount*
10 Rear mount
19 Rear mount*
20 Rear mount
29 Rear mount*
*X9 mounting styles must be ordered with ‘0’ number of sections.
M-9
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
SERIES
NUMBER OF SECTIONS
FUNCTION CODE
Third Angle
Projection
M
Thumbwheel & Pushwheel
Available Terminations: 0, 1, 3
See fi
g
. 1, pa
g
e M-12. Available Terminations: 1
See fi
g
. 1,
p
a
g
e M-12. See fi
g
. 1, pa
g
e M-12.
Available Terminations: 0, 1, 3
21 BCD 1-2-4-8; 10 POSITION14 RESISTOR DECADE; 1-2-2-2-2 CODE
(RESISTORS NOT SUPPLIED)
11 DECIMAL–1 POLE; 10 POSITION
9More than 8 switch sections, specify on CONFIGURATION FORM, page M-15 and consult Customer Service Center.
1-8 Number of switch sections in assembly, includes endplates.
0Switch section only, no assembly. Blank bodies are considered sections; endplates are not sections.
Must be ordered with 09 or 19 mounting style options, see pages M-10 and M-11.
3(STD.) THUMBWHEEL SWITCHES
NOTE: Endplates and blank sections available separately, see pages M-13 and M-14.
NOTE: For terminal location diagram, see page M-12.
M-10
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
FUNCTION CODE
MOUNTING STYLE
Third Angle
Projection
M
Thumbwheel & Pushwheel
Available Terminations: 0, 1, 3
See fi
g
. 1, pa
g
e M-12.
Available Terminations:
B
See fi
g
. 2, pa
g
e M-12. See fi
g
. 1, pa
g
e M-12.
Available Terminations: 0, 1, 3
Available Terminations: 0, 1, 3
See fi
g
. 1, pa
g
e M-12.
N = Number of sections.
PANEL MOUNTING
09 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS
(Must be ordered with number of sections option “0”, see Page M-9.)
00 SWITCH ASSEMBLY W/ ENDPLATES–.315 (8,00) SECTION PITCH
Type 0 Snap-In Front Mount
23 COMPLEMENT OF BCD 1-2-4-8;
10 POSITION 71 BINARY CODED HEXADECIMAL,
16 POSITION
31 BCD 1-2-4-8; 10 POSITION27 BCD 1-2-4-8; 10 POSITION
NOTE: For terminal location diagram, see page M-12.
NOTE: Endplates, blank sections, spacers
and assembly hardware available separately, see pages M-13 and M-14.
(.315 x N) + .326
(8,00 x N) + (8,28)
00
DIM. ‘A’
MOUNTING
STYLE
N = Number of sections.
Recommended panel thickness:
0.46-.125
(1,16-3,18)
M-11
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
MOUNTING STYLE
Third Angle
Projection
M
Thumbwheel & Pushwheel
N = Number of sections.
PANEL MOUNTING
Mtg. Holes
N = Number of sections.
(.350 x N) + .560
(8,89 x N) + (14,22)
(.350 x N) + .340
(8,89 x N) + (8,64)
10
DIM. ‘B’DIM. ‘A’
MOUNTING
STYLE
N = Number of sections.
Recommended panel thickness:
0.46-.125
(1,16-3,18)
20 SWITCH ASSEMBLY W/ ENDPLATES–.350 (8,89) SECTION PITCH
09 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS
(Must be ordered with number of sections option “0”, see Page M-9.)
29 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS
(Must be ordered with number of sections option “0”, see Page M-9.)
19 SWITCH SECTION ONLY–UNASSEMBLED WITHOUT ENDPLATES OR SPACERS
(Must be ordered with number of sections option “0”, see Page M-9.)
10 SWITCH ASSEMBLY W/ ENDPLATES–.350 (8,89) SECTION PITCH
Type 1 Rear Mount
Type 2 Rear Mount
Type 3 Snap1-in Front Mount
NOTE: Endplates, blank sections, spacers and
assembly hardware available separately, see pages M-13 and M-14.
M-12
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
TERMINATIONS
COLOR/MARKING/STOPS
SEAL
Third Angle
Projection
M
Thumbwheel & Pushwheel
Signal traces cut except for common(s).
FIG. 1 FIG. 2
9ANY COMBINATION OF TERMINATION
CONFIGURATIONS OR SPECIAL TERMINATIONS. BTYPE 6 WITH SOLDER PINS
3TYPE 0 WITH SOLDER PINS1TYPE 1, EXTENDED TYPE 0
0(STD.) TYPE 0
3SEALED SWITCHING CONTACTS AND DUST LENS
2DUST LENS. (Protects the character face of the wheel from abrasion and dirt).
1SEALED SWITCHING CONTACTS. (Sealing is by means of an o-ring rotary seal and a cured-in-place elastomer gasket.
Switching contact area is protected from moisture, oil, and airborne contaminants.)
0(STD.) UNSEALED SWITCHING CONTACTS.
0(STD.) MATTE BLACK HOUSING (Gloss black wheel with white characters; no stops.)
PC Board 1/32" (0,79) thick.
NOTE: See function codes, pages M-9 and M-10, for signal locations.
NOTE: Stop pins are available separately, see page M-14.
Dust Lens
NOTE: All terminal holes shown may not be present for all function codes, consult Customer Service Center.
Terminal connector available for termination options 0 & 1, see page M-14.
Specify on configuration form, page M-15
and consult Customer Service Center.
Terminal Location Numbers
M-13
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
AVAILABLE HARDWARE
M
Thumbwheel & Pushwheel
Blank sections, Type 0 & 3,
.315 THK.
PART NO.
413602000 W/RIB-BLACK
413609000 W/RIB-GRAY
400502000 W/RIB & W/OUT SPRINGS-BLACK
400509000 W/RIB & W/OUT SPRINGS-GRAY
Blank sections, Front mount, Type 0 & 3,
.315 THK.
PART NO.
413502000 PLAIN-BLACK
413509000 PLAIN-GRAY
400702000 PLAIN & W/OUT SPRINGS-BLACK
400709000 PLAIN & W/OUT SPRINGS-GRAY
PART NO.
400602000 W/RIB-BLACK
400609000 W/RIB-GRAY
400802000 PLAIN-BLACK
400809000 PLAIN-GRAY
Blank sections, Rear mount, Type 1,
.350 THK.
Blank sections, Rear mount, Type 2,
.350 THK.
PART NO.
473402000 W/RIB-BLACK
473409000 W/RIB-GRAY
473302000 PLAIN-BLACK
473309000 PLAIN-GRAY
End plates, Front mount, Type 0
PART NO.
413402000 BLACK
413409000 GRAY
PART NO.
400402000 BLACK
400409000 GRAY
End plates, Rear mount, Type 1
End plates, Rear mount, Type 2 Stop pins
PART NO.
473202000 BLACK
473209000 GRAY
PART NO.
410802000 BLACK
410809000 GRAY
PART NO.
402900000
Spacers, Front mount, Type 0 & 3, .078 THK.
(Makes section pitch 10mm)
Two required for
complete assembly.
Two required for
complete assembly.
4734 4733
4006 4008
Two required for
complete assembly.
M-14
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
AVAILABLE HARDWARE
M
Thumbwheel & Pushwheel
PART NO.
605A00000 PC
605A02000 SOLDER LUG
Fits 0 & 1 terminations only.
Terminal connector
PART NO.
403500000
Nut
Two nuts required per assembly and screws.
Screws for field assembly of thumbwheel switches
(2 screws needed per assembly + 403500000 nuts)
605A00000 605A02000
PART NO.
406100652
Nut driver (For 403500000 nut)
1–2 1–2
3–4 3
5–7 4–6
8–10 7–9
11–13 10–12
14–16 13–15
412700000
412701000
412702000
412703000
412704000
412705000
NUMBER OF SECTIONS IN ASSEMBLY
FRONT MOUNTING REAR MOUNTING
MTG. STYLE – 00 MTG. STYLE – 10
SCREW PART NUMBER
(0-80 UNF THD. SIZE)
M-15
Dimensions are shown: IN (mm)
Dimensions subject to change
www.ittcannon.com
C&K 3 Series
Thumbwheel Switches
M
Thumbwheel & Pushwheel
QUALITY CONTROL INSTRUCTIONS PRODUCTION APPROVAL DATE
C&K PART NUMBER
REV. INITIALS DATE
3
CATALOG PART NO.
COMPANY NAME CUSTOMER
PRINT
REVISION:
ADDRESS TEL.#
CUSTOMER CONTACT DATE
ORIGINATED BY SALES REP.
DETAILS:
Q.C. APPROVAL DATE
Configuration Form
GRAY SHADED AREAS TO BE FILLED IN BY CUSTOMER SERVICE.
SHEET _____ OF _____
C&K PART NUMBER
10
11
1
2
3
4
5
6
7
8
9
THUMBWHEEL
SECTIONS DESCRIBE IN APPROPRIATE ROW
SPECIAL INSTRUCTIONS OR SPECIFICATIONS:
3 –
FUNCTION CODE – TERMINATIONS–
COLOR/MARKING/STOPS/SEAL –
ILLUMINATION
FOR SWITCHES WITH MORE THAN 11 SECTIONS, CONTINUE ON ADDITIONAL SHEETS.
ENTER OPTION CODES IN APPROPRIATE BOXES. FUNCTION
CODES INCLUDE BLANK SECTIONS (SEE PAGES M-9 & M-10).
NO.
OF
SEC.
– –
3 – – –
3 – – –
3 – – –
3 – – –
3 – – –
3 – – –
3 – – –
3 – – –
3 – – –
3 – – –
