Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
5.0V Surface Mount
Crystal Clock Oscillator
HSM6
XO
The Connor-Winfield models HSM61,
HSM62, and HSM63 are 7.5mm x 5mm,
5.0V HCMOS, Surface Mount, Fixed Fre-
quency Crystal Oscillators (XO) designed
for use in all applications requiring precision
clocks. The RoHS compliant surface mount
package is designed for high-density mount-
ing and is optimum for mass production
Operating Specifications
Parameter Minimum Nominal Maximum Units Notes
Frequency Range (Fo) 1.0 - 80 MHz
Frequency Tolerance - ppm 1
HSM61 -25 25
HSM62 -50 50
HSM63 -100 100
Operating Temp Range -40 - 85 °C
Supply Voltage (Vdd) 4.5 5.0 5.5 Vdc
Supply Current (Icc) - - mA
1.8 to 31.999 MHz 27
32.0 to 49.999 MHz 45
50 to 80.0 MHz 75
Absolute Maximum Ratings
Parameter Minimum Nominal Maximum Units Notes
Storage Temperature -55 - 125 °C
Supply Voltage (Vcc) -0.5 - 7.0 Vdc
Features:
RoHS Compliant
1.0 to 80 MHz
5.0V Operation
Tri-State Enable/Disable Function
Overall Frequency Tolerance:
HSM61 ± 25 ppm, HSM62 ± 50 ppm,
HSM63 ± 100 ppm
Temperature Range: -40 to 85°C
Ceramic Surface Mount Package
Tape and Reel Packaging
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Bulletin SM036
Page 1 of 2
Revision 14
Date 25 March 2010
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Input Characteristics
Parameter Minimum Nominal Maximum Units Notes
Enable Voltage - (Vih) 2.2 - - Vdc 2
Disable Voltage - (Vil) - - 0.8 Vdc
Enable Time - - 100 nS
Disable Time - - 100 nS
HCMOS Output Characteristics
Parameter Minimum Nominal Maximum Units Notes
Load - - 50 pF
Voltage High (Voh) 4.50 - - Vdc
Low (Vol) - - 0.55
Current High (loh) -16 - - mA
Low (lol) - - 16
Duty Cycle at 50% of Vcc 45 50 55 %
Rise / Fall Time 10% to 90% - - 5 nS
Start-Up Time - - 10 mS
Jitter - - 5 pS RMS
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851- 4722
Fax: 630- 851- 5040
www.conwin.com
Bulletin SM036
Page 2 of 2
Revision 14
Date 25 March 2010
Pin Connections
1: Enable/Disable
2: Ground
3: Output
4: Vcc
OSCILLOSCOPE
FREQ
COUNTER
OSC
POWER
SUPPLY
INPUT FOR E/D
PROBE
Vcc
.01uf
Bypass capacitor, C-by, should be
ceramic capacitor ≥ .01 uf
SYMMETRY
Soldering
General Conditions 260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data (Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Environmental Characteristics
Temperature Cycle The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Suggested Pad Layout
Ordering Information
Mechanical Characteristics
Mechanical Shock MIL STD 883 Method 2002
Vibration The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability (EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
After performing the above procedures, a newly soldered coverage shall be greater than 90%
Test Circuit
Output Waveform
Tape and Reel Dimensions
Package Characteristics
Package Hermetically sealed ceramic package and metal cover
Dimensional Tolerance: ±.02" (.508mm)
±.005" (.127mm)
HSM 61044.736M
Type: Temperature
Range:
Frequency
Tolerance:
Supply
Voltage:
Output Frequency:
Clock
7.5x5.0mm
Package
6 = -40 to 85˚C 1 = ± 25 ppm
2 = ± 50 ppm
3 = ± 100 ppm
Omit = 5.0 Vdc
Frequency Format
-xxx.xM Minimum *
-xxx.xxxxxxM Maximum*
*Amount of numbers after the decimal point.
M = MHz
Example: To Order an HSM61 with an output frequency of:
4 MHz = HSM61-004.0M
44.736 MHz = HSM61-044.736M
125 MHz = HSM61-125.0M
Meets EIA-481A and EIAJ-1009B
2,000 PCS/Reel
RoHS Solder Profile
120°C
150°C
180°C
260°C
0
220°C
360 Sec. Max.
120 S
Max. 10 S
60 S
Max.
Time
Temperature 260°C
Meets IPC/JEDEC J-STD-020C
