19-0482; Rev 4; 6/12 Monolithic CMOS Analog Multiplexers Maxim's DG506A/DG507A are monolithic CMOS analog multiplexers. The DG506A is a single 16-channel (1 of 16) multiplexer and the DG507A is a differential 8-channel (2 of 16) multiplexer. Both devices feature break-before-make switching. Maxim guarantees that these multiplexers will not latchup if the power supplies are turned off with the input signals still present as long as absolute maximum ratings are not violated. The multiplexers operate over a wide range of power supplies from Q4.5V to Q18V. Features S S S S S S S Improved 2nd Source Pin Compatible with Harris, Siliconix, Intersil Operable with 4.5V to 18V Supplies Symmetrical, Bidirectional Operation Logic and Enable Inputs, TTL and CMOS Compatible Latch-Up Proof Construction Monolithic, Low-Power CMOS Design Ordering Information PART TEMP RANGE PIN-PACKAGE Compared to the original manufacturer's devices, Maxim's DG506A/DG507A consume significantly less power, making them ideal for portable equipment. DG506AAK -55C to +125C 28 CERDIP DG506ABK -25C to +85C 28 CERDIP DG506AC/D 0C to +70C Dice Maxim's DG506A/DG507A meet or exceed the specifications of, and are drop-in replacements for Intersil's IH6116 and IH6216, Siliconix's DG506A and DG507A, and Harris' HI506 and HI507. DG506ACJ 0C to +70C 28 Plastic Dip DG506ACK 0C to +70C 28 CERDIP DG506ACWI 0C to +70C 28 Wide SO DG506AMWI/PR -55C to +125C 28 Wide SO DG506AAZ/833B -55C to +125C 28 LCC DG507AAK -55C to +125C 28 CERDIP DG507ABK -25C to +85C 28 CERDIP DG507AC/D 0C to +70C Dice Aircraft Heads Up Displays DG507ACJ 0C to +70C 28 Plastic DIP Data Acquisition Systems DG507ACK 0C to +70C 28 CERDIP Signal Routing DG507ACWI 0C to +70C 28 Wide SO Applications Control Systems Data Logging Systems Typical Operating Circuit -15V ANALOG INPUT (OUTPUTS) +15V V+ CLOCK IN BH1 NC S1b S8b A0 Pin Configurations -15V GND VDa DG507A Db A1 A2 EN ANALOG OUTPUT (INPUTS) V+ 1 28 D V+ 1 28 Da NC 2 27 V- Db 2 27 V- NC 3 26 S8 NC 3 26 S8a S16 4 25 S7 S8b 4 25 S7a S15 5 24 S6 S7b 5 23 S5 S6b 6 DG506A 24 S6a DG507A QB S14 6 QC S13 7 22 S4 S5b 7 22 S4a QD S12 8 21 S3 S4b 8 21 S3a S11 9 20 S2 S3b 9 20 S2a S10 10 19 S1 S2b 10 19 S1a S9 11 18 EN S1b 11 18 EN GND 12 17 A0 GND 12 17 A0 NC 13 16 A1 NC 13 16 A1 A3 14 15 A2 NC 14 15 A2 QA AH1 V+ S1a S8a Devices are available in a lead(Pb)-free/RoHS-compliant package, specify lead-free by adding "+" to the part number when ordering. NC r01 r02 GND +15V ENABLE IN (MUX ON-OFF CONTROL) 8-CHANNEL SEQUENTIAL DIFFERENTIAL MUX/DEMUX WIDE SO/DIP 23 S5a WIDE SO/DIP Pin Configurations continued in middle of data sheet. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 DG506A/DG507A General Description DG506A/DG507A Monolithic CMOS Analog Multiplexers ABSOLUTE MAXIMUM RATINGS (Voltages referenced to V-.) V+...........................................................................................44V GND........................................................................................25V Digital Inputs VS, VD (Note 1)........................-2V to (V+ + 2V) or 20mA, whichever occurs first Current, Any Terminal Except S or D..................................30mA Continuous Current, S or D.................................................20mA Peak Current, S or D (pulsed at 1ms, 10% duty cycle max).... 40mA Continuous Power Dissipation (TA = +70C)* 28-Pin Ceramic DIP (derate 16.7mW/NC above +70NC)..1333mW 28-Pin Plastic DIP (derate 14.3mW/NC above +70NC)...1143mW 28-Pin Wide SO (derate 12.5mW/C above +70C)..1000mW 28-Pin LCC (derate 10.2mW/C above +70C)........816.3mW Operating Temperature Range (A Suffix)......... -55NC to +125NC (B Suffix)........... -25NC to +85NC (C Suffix)................. 0NC to +70N Storage Temperature (A and B Suffix).............. -65NC to +150NC (C Suffix)........................ -65NC to +125NC Lead Temperature (soldering, 10s).................................+300NC Soldering Temperature (reflow) Lead (Pb)-free packages.............................................+260NC Packages containing lead (Pb)....................................+240NC *All leads soldered or welded to PCB. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, VGND = 0V, TA = +25NC, unless otherwise indicated.) PARAMETER SYMBOL CONDITIONS DG506AA DG507AA MIN TYP (Note 2) (Note 3) DG506AB/C DG507AB/C MAX MIN TYP (Note 2) (Note 3) UNITS MAX SWITCH Analog Signal Range Drain-toSource On-Resistance Greatest Change in Drain-Source On-Resistance Between Channels Source OffLeakage Current Drain OffLeakage Current 2 VANALOG RDS(ON) RDS(ON) IS(OFF) -15 Sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VD = 10V, IS = -200FA 270 230 ID(OFF) DG507A, VEN = 0.8V, VAL = 0.8V 400 +15 270 400 230 6 -10V P VS P +10V DG506A, VEN = 0.8V, VAL = 0.8V -15 V 450 I VD = -10V, IS = -200FA R DS(ON)MAX - R DS(ON)MIN R DS(ON) = R DS(ON)AVE VEN = 0.8V, VAL = 0.8V +15 450 6 % VS = 10V, VD = -10V -1 0.002 +1 -5 0.002 +5 VS = -10V, VD = 10V -1 -0.005 +1 -5 -0.005 +5 VD = 10V, VS = -10V -10 0.02 +10 -20 0.02 +20 VD = -10V, VS = 10V -10 -0.03 +10 -20 -0.03 +20 VD = 10V, VS = -10V -5 0.007 +5 -10 0.007 +10 VD = -10V, VS = 10V -5 -0.015 +5 -10 -0.015 +10 nA nA Monolithic CMOS Analog Multiplexers DG506A/DG507A ELECTRICAL CHARACTERISTICS (continued) (V+ = 15V, V- = -15V, VGND = 0V, TA = +25NC, unless otherwise indicated.) PARAMETER Channel On-Leakage Current SYMBOL ID(ON) (Note 4) CONDITIONS DG506AA DG507AA MIN TYP (Note 2) (Note 3) DG506AB/C DG507AB/C MAX MIN TYP (Note 2) (Note 3) UNITS MAX DG506A, sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VS(all) = VD = 10V -10 0.03 +10 -20 0.03 +20 VS(all) = VD = -10V -10 -0.06 +10 -20 -0.06 +20 DG507A, sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VS(all) = VD = 10V -5 0.015 +5 -10 0.015 +10 VS(all) = VD = -10V -5 -0.03 +5 -10 -0.03 +10 -10 -0.002 -10 -0.002 nA INPUT Address Input Current, InputVoltage High IAH Address Input Current, InputVoltage Low IAL VA = 2.4V VA = 15V All VA = 0V 0.006 10 0.006 VEN = 2.4V -10 -0.002 -10 -0.002 VEN = 0V -10 -0.002 -10 -0.002 10 FA FA DYNAMIC Switching Time of Multiplexer ttransition Figure 1 0.6 Break-BeforeMake Interval tOPEN Figure 3 Enable TurnOn Time tON(EN) Enable TurnOff Time tOFF(EN) Off-Isolation (Note 5) 1 0.06 Fs 0.2 0.2 Fs Figure 2 1 1 Fs Figure 2 0.4 0.4 Fs OIRR VEN = 0V, RL = 1kI, CL = 15pF, VS = 7VRMS, f = 500kHz 68 68 dB Source OffCapacitance CS(OFF) VEN = 0V, f = 140kHz, VS = 0V 6 6 pF Drain OffCapacitance CD(OFF) VEN = 0V, f = 140kHz DG506A, VD = 0V 45 45 DG507A, VD = 0V 23 23 pF SUPPLY Positive Supply Current I+ Negative Supply Current I- VEN = 0 or 5V, all VA = 0V 0.13 0.25 0.13 0.3 mA VEN = 0 or 5V, all VA = 0V -0.15 -0.07 -0.25 -0.07 3 DG506A/DG507A Monolithic CMOS Analog Multiplexers ELECTRICAL CHARACTERISTICS (Overtemperature) (V+ = 15V, V- = -15V, VGND = 0V, TA = overtemperature range, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS DG506AA DG507AA MIN TYP (Note 2) (Note 3) DG506AB/C DG507AB/C MAX MIN TYP (Note 2) (Note 3) UNITS MAX SWITCH Analog Signal Range Drain-to-Source On-Resistance Source OffLeakage Current Drain OffLeakage Current Channel On-Leakage Current VANALOG RDS(ON) IS(OFF) -15 Sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V -15 500 +15 I VD = -10V, IS = -200FA 500 550 -50 VS = -10V, VD = 10V -50 +50 -50 +50 VD = 10V, VS = -10V -300 +300 -300 +300 VD = -10V, VS = 10V -300 +300 -300 +300 VD = 10V, VS = -10V -200 +200 -200 +200 VD = -10V, VS = 10V -200 +200 -200 +200 DG506A, sequence each switch on, VAL = 0.8V, VAN = 2.4V, VEN = 2.4V VS(all) = VD = 10V -300 +300 -300 +300 VS(all) = VD = -10V -300 +300 -300 +300 DG507A, sequence each switch on, VAL = 0.8V, VAN = 2.4V, VEN = 2.4V VS(all) = VD = 10V -200 +200 -200 +200 VS(all) = VD = -10V -200 +200 -200 +200 ID(OFF) DG507A, VEN = 0.8V, VAL = 0.8V V 550 VS = 10V, VD = -10V VEN = 0.8V, VAL = 0.8V DG506A, VEN = 0.8V, VAL = 0.8V ID(ON) (Note 4) VD = 10V, IS = -200FA +15 +50 -50 +50 nA nA nA INPUT 4 Address Input Current, InputVoltage High IAH Address Input Current, InputVoltage Low IAL VA = 2.4V -30 VA = 15V All VA = 0V -30 30 VEN = 2.4V VEN = 0V -30 30 FA -30 30 30 FA Monolithic CMOS Analog Multiplexers (V+ = 15V, V- = -15V, VGND = 0V, TA = over temperature range, unless otherwise noted.) Note 1: Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. Note 2: The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. Note 3: Typical values are for design aid only, not guaranteed nor subject to production testing. Note 4: ID(ON) is leakage from driver into on switch. Note 5: Off-isolation = 20log x VO/VS, VS = input to off switch, VD = output due to VS. Truth Tables A3 A2 A1 A0 EN ON SWITCH A2 A1 A0 EN ON SWITCH X X X X 0 None X X X 0 None 0 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 2 0 0 1 1 2 0 0 1 0 1 3 0 1 0 1 3 0 0 1 1 1 4 0 1 1 1 4 0 1 0 0 1 5 1 0 0 1 5 0 1 0 1 1 6 1 0 1 1 6 0 1 1 0 1 7 1 1 0 1 7 0 1 1 1 1 8 1 1 1 1 8 1 0 0 0 1 9 1 0 0 1 1 10 1 0 1 0 1 11 1 0 1 1 1 12 1 1 0 0 1 13 1 1 0 1 1 14 1 1 1 0 1 15 1 1 1 1 1 16 Note: Logic "0" = VAL 0.8V, Logic "1" = VAH 2.4V, "0" = Don't Care. Switching Time Test Circuits +2.4V EN A3 A2 A1 A0 LOGIC INPUT +2.4V +15V V+ S1 S2 THRU S15 DG506A S16 D GND V- 50 -15V Figure 1a. Transition Switching Time 10V EN 10V 1M +15V 35pF SWITCH OUTPUT VO A2 A1 A0 LOGIC INPUT V+ S1b S1a THRU S8a, Da S2b, AND S7b 10V S8b Db 10V DG507A GND V- 50 1M 35pF SWITCH OUTPUT VO -15V Figure 1b. Transition Switching Time 5 DG506A/DG507A ELECTRICAL CHARACTERISTICS (Overtemperature) (continued) DG506A/DG507A Monolithic CMOS Analog Multiplexers Switching Time Test Circuits (continued) +15V EN A3 A2 A1 A0 LOGIC INPUT 50 V+ -5V S1 S2 THRU S16 DG506A V- GND D 1k 3V 50% 0 LOGIC INPUT tr < 20ns ti < 20ns 35pF SWITCH OUTPUT VO SWITCH OUTPUT VO (SEE FIGURE 1) TRANSITION TIME -15V VS1 0.8 VS1 0 0.8 VS8 VS8 ttransition S1 ON Figure 2a. Enable Switching Time SWITCH OUTPUT VO (SEE FIGURE 2) ENABLE t(ON)/t(OFF) TIME +15V EN A2 A1 A0 LOGIC INPUT 50 V+ -5V S1b S1a THRU S4a, Da, S2b, S3b, S4b DG507A V- GND Db 1k 35pF SWITCH OUTPUT VO -15V SWITCH OUTPUT VO (SEE FIGURE 3) OPEN TIME BREAK-BEFORE-MAKE INTERVAL Figure 2b. Enable Switching Time S8 ON tON (En) 0 0.1 VO toff (En) 0.9 VO VO VS VS 50% 0V tOPEN Figure 4. Timing Diagrams for Figures 1, 2, and 3 +2.4V +15V EN V+ ALL S AND Da VS = +5V DG506A DG507A LOGIC INPUT A0 A1 A2 A3 GND Db, D V- 50 -15V Figure 3. Break-Before-Make 6 1k 35pF SWITCH OUTPUT VO ttransition Monolithic CMOS Analog Multiplexers V+ 1 IN8 N.C. 2 V- N.C. 3 OUT IN16 4 28 27 26 IN15 5 25 IN7 IN14 6 24 IN6 IN13 7 23 IN5 IN12 8 22 IN4 IN11 9 21 IN3 IN10 10 20 IN2 IN9 11 19 IN1 EN A0 A1 A2 18 A3 16 17 N.C. 12 13 14 15 GND DG506A LCC N.C. = NO INTERNAL CONNECTION Pin Description PIN DG506A DIP / SO DG507A DIP / SO NAME 1 1 V+ 2, 3 3 N.C. FUNCTION Positive Supply Voltage Input No Connection. Internally not connected. -- 2 Db Analog Output Bidirectional Channel b 4 -- S16 Analog Output Bidirectional Channel 16 -- 4 S8b Analog Output Bidirectional Channel 8b 5 -- S15 Analog Output Bidirectional Channel 15 -- 5 S7b Analog Output Bidirectional Channel 7b 6 -- S14 Analog Output Bidirectional Channel 14 -- 6 S6b Analog Output Bidirectional Channel 6b 7 -- S13 Analog Output Bidirectional Channel 13 -- 7 S5b Analog Output Bidirectional Channel 5b 8 -- S12 Analog Output Bidirectional Channel 12 -- 8 S4b Analog Output Bidirectional Channel 4b 9 -- S11 Analog Output Bidirectional Channel 11 -- 9 S3b Analog Output Bidirectional Channel 3b 10 -- S10 Analog Output Bidirectional Channel 10 -- 10 S2b Analog Output Bidirectional Channel 2b 11 -- S9 Analog Output Bidirectional Channel 9 -- 11 S1b Analog Output Bidirectional Channel 1b 12 12 GND Ground 7 DG506A/DG507A Pin Configurations (continued) Monolithic CMOS Analog Multiplexers DG506A/DG507A Pin Description (continued) PIN 8 DG506A DIP / SO DG507A DIP / SO NAME FUNCTION 13 13, 14 N.C. 14 -- A3 Address Input A3 15 15 A2 Address Input A2 16 16 A1 Address Input A1 17 17 A0 Address Input A0 18 18 EN Enable Input 19 -- S1 Analog Output Bidirectional Channel 1 -- 19 S1A Analog Output Bidirectional Channel 1a No Connection. Not internally connected. 20 -- S2 Analog Output Bidirectional Channel 2 -- 20 S2A Analog Output Bidirectional Channel 2a 21 -- S3 Analog Output Bidirectional Channel 3 -- 21 S3A Analog Output Bidirectional Channel 3a 22 -- S4 Analog Output Bidirectional Channel 4 -- 22 S4A Analog Output Bidirectional Channel 5 23 -- S5 Analog Output Bidirectional Channel 5a -- 23 S5a Analog Output Bidirectional Channel 6 24 -- S6 Analog Output Bidirectional Channel 6a -- 24 S6a Analog Output Bidirectional Channel 7 25 -- S7 Analog Output Bidirectional Channel 7a -- 25 S7a Analog Output Bidirectional Channel 8 26 -- S8 Analog Output Bidirectional Channel 8a -- 26 S8a Analog Output Bidirectional Channel 27 27 V- Negative Supply Voltage Input 28 -- D Analog Output Bidirectional -- 28 Da Analog Output Bidirectional Channel a Monolithic CMOS Analog Multiplexers PIN DG506A LCC NAME FUNCTION 1 V+ 2, 3 N.C. Positive Supply Voltage Input NoConnection. Internally not connected. 4 IN16 Analog Input Bidirectional Channel 16 5 IN15 Analog Input Bidirectional Channel 15 6 IN14 Analog Input Bidirectional Channel 14 7 IN13 Analog Input Bidirectional Channel 13 8 IN12 Analog Input Bidirectional Channel 12 9 IN11 Analog Input Bidirectional Channel 11 10 IN10 Analog Input Bidirectional Channel 10 11 IN9 Analog Input Bidirectional Channel 9 12 GND Ground 13 N.C. No Connection. Not internally connected. 14 A3 Address Input A3 15 A2 Address Input A2 16 A1 Address Input A1 17 A0 Address Input A0 18 EN Enable Input 19 IN1 Analog Input Bidirectional Channel 1 20 IN2 Analog Input Bidirectional Channel 2 21 IN3 Analog Input Bidirectional Channel 3 22 IN4 Analog Input Bidirectional Channel 4 23 IN5 Analog Input Bidirectional Channel 5 24 IN6 Analog Input Bidirectional Channel 6 25 IN7 Analog Input Bidirectional Channel 7 26 IN8 Analog Input Bidirectional Channel 8 27 V- Negative Supply Voltage Input 28 OUT Analog Output Bidirectional Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix number, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 28 CERDIP J28-2 21-0046 -- 28 Plastic DIP P28-2 21-0044 -- 28 Wide SO W28-5 21-0042 90-0109 28 Wide SO W28-5 21-0047 90-0178 28 LCC L28-2 21-4497 90-0178 9 DG506A/DG507A Pin Description (continued) DG506A/DG507A Monolithic CMOS Analog Multiplexers Revision History REVISION NUMBER REVISION DATE 0 8/92 Initial release 1 1/99 Updated to Word format. 2 5/09 Added ruggedized plastic part. 3 2/10 * Added lead temperature to the Absolute Maximum Ratings. * Changed the derate rate of all packages to above 70C in the Absolute Maximum Ratings. 4 6/12 Added DG506AAZ/883B; added the Pin Descriptions for DG506A DIP/SO, DG507A DIP/SO, DG506A LCC; added LCC Pin Configuration for the DG506A DESCRIPTION PAGES CHANGED -- 1-7 1-4, 7 2 1, 2, 7, 9 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. 10 (c) Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 2012 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.