2013-09-20 High Power Infrared Emitter (850 nm) IR-Lumineszenzdiode (850 nm) mit hoher Ausgangsleistung Version 1.1 SFH 4253 Features: Besondere Merkmale: * High Power Infrared LED * Short switching time * Infrarot LED mit sehr hoher Ausgangsleistung * Kurze Schaltzeit Applications Anwendungen * Infrared Illumination for cameras * IR data transmission * Sensor technology * Infrarotbeleuchtung fur Kameras * IR Datenubertragung * Sensorik Notes Hinweise Depending on the mode of operation, these devices emit highly concentrated non visible infrared light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions given in IEC 60825-1 and IEC 62471. Je nach Betriebsart emittieren diese Bauteile hochkonzentrierte, nicht sichtbare Infrarot-Strahlung, die gefahrlich fur das menschliche Auge sein kann. Produkte, die diese Bauteile enthalten, mussen gema den Sicherheitsrichtlinien der IEC-Normen 60825-1 und 62471 behandelt werden. Ordering Information Bestellinformation Type: Radiant Intensity Ordering Code Typ: Strahlstarke Bestellnummer IF = 70 mA, tp = 20 ms Ie [mW/sr] SFH 4253 13 ( 6.3) Note: Measured at a solid angle of = 0.01 sr Anm.: Gemessen bei einem Raumwinkel = 0.01 sr 2013-09-20 Q65110A6657 1 Version 1.1 SFH 4253 Maximum Ratings (TA = 25 C) Grenzwerte Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Operation and storage temperature range Betriebs- und Lagertemperatur Top; Tstg -40 ... 100 C Reverse voltage Sperrspannung VR 5 V Forward current Durchlassstrom IF 70 mA Surge current Stostrom (tp = 100 s, D = 0) IFSM 0.7 A Total power dissipation Verlustleistung Ptot 140 mW Thermal resistance junction - ambient 1) page 11 Warmewiderstand Sperrschicht - Umgebung RthJA 500 K/W Thermal resistance junction - soldering point RthJS 280 K/W 1) Seite 11 2) page 11 Wamewiderstand Sperrschicht - Lotstelle 2) Seite 11 Characteristics (TA = 25 C) Kennwerte Parameter Bezeichnung Symbol Values Symbol Werte Unit Einheit Emission wavelength Zentrale Emissionswellenlange (IF = 70 mA, tp = 20 ms) (typ) peak 860 nm Centroid Wavelength Schwerpunktwellenlange der Strahlung (IF = 70 mA, tp = 20 ms) (typ) centroid 850 nm Spectral bandwidth at 50% of Imax Spektrale Bandbreite bei 50% von Imax (IF = 70 mA, tp = 20 ms) (typ) 30 nm Half angle Halbwinkel (typ) 60 Active chip area Aktive Chipflache (typ) A 0.04 mm2 2013-09-20 2 Version 1.1 SFH 4253 Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Dimensions of active chip area Abmessungen der aktiven Chipflache (typ) LxW Rise and fall time of Ie ( 10% and 90% of Ie max) Schaltzeit von Ie ( 10% und 90% von Ie max) (IF = 70 mA, RL = 50 ) (typ) tr, tf Forward voltage Durchlassspannung (IF = 70 mA, tp = 20 ms) 0.2 x 0.2 mm x mm 12 ns (typ (max)) VF 1.6 ( 2) V Forward voltage Durchlassspannung (IF = 500 mA, tp = 100 s) (typ (max)) VF 2.4 ( 3) V Reverse current Sperrstrom (VR = 5 V) (typ (max)) IR Total radiant flux Gesamtstrahlungsfluss (IF = 70 mA, tp = 20 ms) (typ) e 40 mW Temperature coefficient of Ie or e Temperaturkoeffizient von Ie bzw. e (IF = 70 mA, tp = 20 ms) (typ) TCI -0.5 %/K Temperature coefficient of VF Temperaturkoeffizient von VF (IF = 70 mA, tp = 20 ms) (typ) TCV -0.7 mV / K Temperature coefficient of wavelength Temperaturkoeffizient der Wellenlange (IF = 70 mA, tp = 20 ms) (typ) TC 0.3 nm / K 2013-09-20 3 not designed for A reverse operation Version 1.1 SFH 4253 Grouping (TA = 25 C) Gruppierung Group Min Radiant Intensity Max Radiant Intensity Typ Radiant Intensity Gruppe Min Strahlstarke Max Strahlstarke Typ Strahlstarke IF = 70 mA, tp = 20 ms IF = 70 mA, tp = 20 ms IF = 500 mA, tp = 25 s Ie, min [mW / sr] Ie, max [mW / sr] Ie, typ [mW / sr] SFH 4253-Q 6.3 12.5 37 SFH 4253-R 10 20 60 Note: measured at a solid angle of = 0.01 sr Only one group in one packing unit (variation lower 2:1). Anm.: gemessen bei einem Raumwinkel = 0.01 sr Nur eine Gruppe in einer Verpackungseinheit (Streuung kleiner 2:1). Relative Spectral Emission 3) page 11 Relative spektrale Emission 3) Seite 11 Radiant Intensity 3) page 11 Strahlstarke 3) Seite 11 Irel = f(), TA = 25C 100 I rel Ie / Ie(70 mA) = f(IF), single pulse, tp = 25 s, TA = 25C OHF04132 OHF04406 101 % Ie I e (70 mA) 80 100 5 60 10-1 5 40 10-2 20 0 700 5 750 800 850 10-3 0 10 nm 950 5 10 2 mA IF 2013-09-20 5 10 1 4 10 3 Version 1.1 SFH 4253 Forward Current 3) page 11 Durchlassstrom 3) Seite 11 Max. Permissible Forward Current Max. zulassiger Durchlassstrom IF, max = f(TA), RthJA = 500 K / W IF IF = f(VF), single pulse, tp = 100 s, TA= 25C OHF03732 80 mA IF 70 OHF03826 100 A 10-1 60 5 50 10-2 40 5 30 10-3 20 5 10 0 0 20 40 60 80 10-4 100 C 120 0 0.5 1 1.5 2 2.5 V 3 TA VF Permissible Pulse Handling Capability Zulassige Pulsbelastbarkeit Permissible Pulse Handling Capability Zulassige Pulsbelastbarkeit IF = f(tp), TA = 25 C, duty cycle D = parameter IF 0.7 A 0.6 0.5 0.4 0.3 0.2 IF = f(tp), TA = 85 C, duty cycle D = parameter OHF03733 t D = TP tP IF IF T 0.6 D= 0.5 0.005 0.01 0.02 0.05 0.1 0.2 0.3 0.5 1 0.4 0.3 0.2 0.1 0.1 0 -5 10 10-4 10-3 10-2 10-1 100 101 s 102 OHF03824 t tP D = TP IF T D= 0.005 0.01 0.02 0.05 0.1 0.2 0.3 0.5 1 0 -5 10 10-4 10-3 10-2 10-1 100 101 s 102 tp tp 2013-09-20 0.7 A 5 Version 1.1 SFH 4253 Radiation Characteristics 3) page 11 Abstrahlcharakteristik 3) Seite 11 Irel = f() 40 30 20 10 0 50 OHL01660 1.0 0.8 0.6 60 0.4 70 0.2 80 0 90 100 1.0 0.8 0.6 0.4 0 20 40 60 80 100 Package Outline Mazeichnung 2.1 (0.083) 3.0 (0.118) 2.6 (0.102) 2.3 (0.091) 1.7 (0.067) 0.1 (0.004) (typ.) 0.9 (0.035) 0.7 (0.028) 3.7 (0.146) 3.3 (0.130) 41 (2.4) (0.095) 3.4 (0.134) 3.0 (0.118) 2.1 (0.083) A 0.5 (0.020) Cathode marking 1.1 (0.043) C 0.18 (0.007) 0.12 (0.005) 0.6 (0.024) 0.4 (0.016) GPLY6724 Dimensions in mm (inch). / Mae in mm (inch). 2013-09-20 6 120 Version 1.1 SFH 4253 Package TOPLED, clear resin Gehause TOPLED, klarer Verguss Method of Taping Gurtung 2.9 (0.114) 4 (0.157) Dimensions in mm (inch). / Mae in mm (inch). 2013-09-20 7 8 (0.315) Cathode/Collector Marking 1.75 (0.069) 2 (0.079) 3.5 (0.138) 4 (0.157) 3.6 (0.142) 1.5 (0.059) OHAY2271 Version 1.1 SFH 4253 Recommended Solder Pad Empfohlenes Lotpaddesign 4.5 (0.177) 2.6 (0.102) 1.5 (0.059) 1.5 (0.059) 4.5 (0.177) 2.6 (0.102) Padgeometrie fur verbesserte Warmeableitung Lotstopplack Solder resist Paddesign for improved heat dissipation OHLPY970 Dimensions in mm (inch). / Mae in mm (inch). 2013-09-20 Cu-Flache > 16 mm 2 Cu-area > 16 mm 2 8 Version 1.1 SFH 4253 Reflow Soldering Profile Reflow-Lotprofil Preconditioning: JEDEC Level 2 acc. to JEDEC J-STD-020D.01 OHA04525 300 C T 250 Tp 245 C 240 C tP 217 C 200 tL 150 tS 100 50 25 C 0 0 50 100 150 200 s 300 250 t OHA04612 Profile Feature Profil-Charakteristik Symbol Symbol Pb-Free (SnAgCu) Assembly Minimum Ramp-up rate to preheat*) 25 C to 150 C Time tS TSmin to TSmax tS 60 Ramp-up rate to peak*) TSmax to TP Recommendation Maximum 2 3 100 120 2 3 Unit Einheit K/s s K/s Liquidus temperature TL 217 Time above liquidus temperature tL 80 100 s Peak temperature TP 245 260 C Time within 5 C of the specified peak temperature TP - 5 K tP 20 30 s 3 6 K/s 10 Ramp-down rate* TP to 100 C 480 Time 25 C to TP All temperatures refer to the center of the package, measured on the top of the component * slope calculation DT/Dt: Dt max. 5 s; fulfillment for the whole T-range 2013-09-20 C 9 s Version 1.1 SFH 4253 Disclaimer Disclaimer Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS. Bitte beachten! Lieferbedingungen und Anderungen im Design vorbehalten. Aufgrund technischer Anforderungen konnen die Bauteile Gefahrstoffe enthalten. Fur weitere Informationen zu gewunschten Bauteilen, wenden Sie sich bitte an unseren Vertrieb. Falls Sie dieses Datenblatt ausgedruckt oder heruntergeladen haben, finden Sie die aktuellste Version im Internet. Verpackung Benutzen Sie bitte die Ihnen bekannten Recyclingwege. Wenn diese nicht bekannt sein sollten, wenden Sie sich bitte an das nachstgelegene Vertriebsburo. Wir nehmen das Verpackungsmaterial zuruck, falls dies vereinbart wurde und das Material sortiert ist. Sie tragen die Transportkosten. Fur Verpackungsmaterial, das unsortiert an uns zuruckgeschickt wird oder das wir nicht annehmen mussen, stellen wir Ihnen die anfallenden Kosten in Rechnung. Bauteile, die in lebenserhaltenden Apparaten und Systemen eingesetzt werden, mussen fur diese Zwecke ausdrucklich zugelassen sein! Kritische Bauteile* durfen in lebenserhaltenden Apparaten und Systemen** nur dann eingesetzt werden, wenn ein schriftliches Einverstandnis von OSRAM OS vorliegt. *) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system. **) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered. *) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems fuhren wird oder die Sicherheit oder Effektivitat dieses Apparates oder Systems beeintrachtigt. **) Lebenserhaltende Apparate oder Systeme sind fur (a) die Implantierung in den menschlichen Korper oder (b) fur die Lebenserhaltung bestimmt. Falls Sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist. 2013-09-20 10 Version 1.1 SFH 4253 Glossary Glossar 1) Thermal resistance: junction -ambient, mounted on PC-board (FR4), padsize 16 mm2 each 1) Warmewiderstand: Sperrschicht -Umgebung, bei Montage auf FR4 Platine, Padgroe je 16 mm2 2) Thermal resistance: junction mounted on metal block point, 2) Warmewiderstand: Sperrschicht Montage auf Metall-Block 3) Typical Values: Due to the special conditions of the manufacturing processes of LED, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could differ from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice. 3) Typische Werte: Wegen der besonderen Prozessbedingungen bei der Herstellung von LED konnen typische oder abgeleitete technische Parameter nur aufgrund statistischer Werte wiedergegeben werden. Diese stimmen nicht notwendigerweise mit den Werten jedes einzelnen Produktes uberein, dessen Werte sich von typischen und abgeleiteten Werten oder typischen Kennlinien unterscheiden konnen. Falls erforderlich, z.B. aufgrund technischer Verbesserungen, werden diese typischen Werte ohne weitere Ankundigung geandert. 2013-09-20 -soldering 11 -Lotstelle, bei Version 1.1 SFH 4253 Published by OSRAM Opto Semiconductors GmbH Leibnizstrae 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. 2013-09-20 12