®
Data Device Cor poration
105 Wilbur Place
Bohemia, New York 11716
631-567-5600 Fax: 631-567-7358
www.ddc-web.com
FOR MORE INFORMATION CONTACT:
Technical Suppor t:
1-800-DDC-5757 ext. 7771
FEATURES
•7 VA Drive Capability for CT, CDX, or
TR Loads
•Double Buffered Transparent Input
Latch
•16-Bit Resolution
•Up to 2 Minute Accuracy
•Power Amplifier Uses Pulsating or DC
Supplies
•Built-In-Test (BIT) Output
DESCRIPTION
The DSC-10510 is a high power Digital-to-Synchro converter, with
16-bit resolution and up to ±2 minute accuracy. The DSC-10510 is
capable of driving multiple Control Transf ormer (CT), Control Diff erential
Transmitter (CDX) and Torque Receiver (TR) loads up to 7 VA.
The DSC-10510 contains a high accuracy D/R con verter , a triple power
amplifier stage, a walk-around circuit (to prevent torque receiver
hangups), and thermal and over-current protection circuits. The hybrid
is protected against over loads, load transients, over-temperature, loss
of reference, and power amplifier or DC power supply shutdown.
Microprocessor compatibility is provided through a 16-bit/2-byte dou-
ble-buffered input latch. Data input is natural binary angle in TTL
compatible parallel positive logic for mat.
P ac kaged in a 40-pin TDIP, the DSC-10510 f eatures a power stage that
may be dr iven by either a standard ±15 VDC supply or by a pulsating
reference supply when used with an optional power transformer.When
powered by the reference source, heat dissipation is reduced by 50%.
APPLICATIONS
The DSC-10510 can be used where digitized shaft angle data must be
conver ted to an analog format for driving CT’s, CDX’s, and TR loads.
With its double b uff ered input latches, the DSC-10510 easily interf aces
with microprocessor based systems such as flight simulators, flight
instrumentation, fire control systems, and flight data computers.
© 1986, 1999 Data Device Corporation
DDC Custom Monolithics utilized in this product are copyright
under the Semiconductor Chip Protection Act.
DSC-10510
7 VA DIGITAL-TO-SYNCHRO (D/S)
CONVERTER
Make sure the next
Card you purchase
has...
M
2
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
FIGURE 1. DSC-10510 BLOCK DIAGRAM
D/R CONVERTER
HIGH ACCURACY
LOW SCALE FACTOR
VARIATION
ELECTRONIC SCOTT-T
& TRIPLE POWER
AMPLIFIER
WALK AROUND CIRCUIT
TRANSPARENT
LATCH
TRANSPARENT
LATCH
DELAY
OVER-CURRENT POWER STAGE
ENABLE
THERMAL SENSE
140˚ CASE
REMOTE
SENSE
19 S1'
20 S1 S1
25 S2'
21 S2 S2
26 S3'
22 S3 S3
BIT
39
±15 VDC
- R
-R 37
EN BS
38
40
K
±15 VDC
BITS 9-16
9-16 32
LL
1-8
BITS 1-8
LM
33
28 31
LA
3.4 V
REF
RH' 13k
35
RL' 13k
34
26 V
REF
RH 100k
18
RL 100k
17
R
36
-R
30
+15 VDC -15 VDC +V OR +15 V
29 23
SIN
COS
-V OR -15 V
24
-
+
3
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
TABLE 1. DSC-10510 SPECIFICATIONS
PARAMETER VALUE DESCRIPTION
RESOLUTION 16 bits Bit 1 = MSB, Bit 16 = LSB
ACCURACY ±2 or 4 minutes (Note 1)
DIFFERENTIAL LINEARITY 1 LSB max in the 16th bit
OUTPUT SETTLING TIME 40 µs max For any digital input step change (passive loads)
DIGITAL INPUT/OUTPUT
Logic Type
Digital Inputs
Loading
K
Digital Outputs
BIT
Drive Capability
Logic 0 = 0.8 V max
Logic 1 = 2.0 V min
20 µA max to GND//5pf max
20 µA max to +5V//5pf max
20 µA max
Logic 0 = 1 TTL Load
Logic 1 = 10 TTL Loads
TTL/CMOS compatible
All inputs except K
(Kick pin 40)
Bits 1 - 16, BS, and EN
LL, LM, and LA (CMOS transient protected)
Ground to enable Kick circuit, open to disable; pulls self up to +15V.
Logic 0 for BIT condition (see BIT pin function)
1.6mA at 0.4V max
0.4mA at 2.8V min
REFERENCE INPUT
Type
Max Voltage w/o Damage
Frequency
Input Impedance
Single Ended
Differential
26 Vrms differential
3.4 Vrms differential
72.8 Vr ms for RH - RL
9.52 Vr ms for RH' - RL'
DC to 1 kHz
100k Ohms ±0.5%
13k Ohms ±0.5%
200k Ohms ±0.5%
26k Ohms ±0.5%
RH - RL
RH' - RL'
RH - RL
RH' - RL'
RH - RL
RH' - RL'
SYNCHRO OUTPUT
Voltage L-L
Scale Factor Variation
Current
CT, CDX or TR Load
DC Offset
Protection
11.8 Vr ms ±0.5% for nom Ref V
±0.1% max
700 mA rms max
7 VA max
±15 mV max
Simultaneous amplitude variation on all output lines as a function of digi-
tal angle.
Each line to ground.Varies with angle.
Output protected from overcurrent, voltage feedback transient, and over
temperature, loss of reference, loss of power amplifier, and loss of ±DC
supply voltage.
POWER SUPPLY CHARACTERISTICS
Nominal Voltage
Voltage Range
Max Voltage w/o Damage
Current
±15 V
±5%
18V
25 mA max
±V
20 V peak max,
3 V above output min
25 V
load dependent
TEMPERATURE RANGES
Operating (Case)
-3XX
-1XX
Storage
0°C to +70°C
-55°C to +125°C
-65°C to +150°C
PHYSICAL CHARACTERISTICS
Size
Weight
2.0 x 1.1 x 0.2 inches
(50.8 x 27.9 x 5.1 mm)
0.9 oz
(25.5 g)
40 Pin Tr iple DIP
Note 1: DSC-10510-303 accuracy = ±4 minutes (No Load) + 1.6 minutes at full load (7 VA Inductive)
DSC-10510-304 accuracy = ±2 minutes (No Load) + 1.6 minutes at full load (7 VA Inductive)
4
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
INTRODUCTION
SYSTEM CONSIDERATIONS:
POWER SURGE AT TURN ON
The output power stages can fully turn on before all the supplies
stabilize, when power is initially applied. Multiple D/S converters
with substantial loads can cause the system power supply to
have difficulty coming up and may even cause the supply to shut
down. It is impor tant that the power supply can handle the turn-
on surge or that the D/S turn-ons be staggered. Typically, the
surge will be twice the max rated draw of the converter.
POWER SUPPLY CYCLING
Power supply cycling of the DSC-10510 should follow the guide-
lines below to avoid any potential problems.
Strictly maintain proper sequencing of supplies and signals per
typical CMOS circuit guidelines:
- Apply power supplies first (+15, -15V and ground).
- Apply digital control signals next.
- Apply analog signals last.
The reverse sequence should be followed during power down of
the circuit.
It is also recommended that the KICK pin, if unused, be left in the
“No Connection” (N/C) state.The inter nal pull up will disable the
pin (this removes any unnecessary v oltages from the converter).
TORQUE LOAD MANAGEMENT
The above problems are compounded by the high power levels
inv olv ed when m ultiple torque loads (TR) are being driven.In this
configuration, power supply fold back problems are common
unless the stagger technique is used. The load will also need
time to stabilize. On tur n-on it is likely that some of output loads
will be at a diff erent angle than the D/S output.As the angular dif-
ference increases so does the power draw until the difference is
180 degrees. At this point the load impedance drops to Zss and
current draw is at a maximum.
PULSATING POWER SUPPLIES
D/S and D/R conv erters hav e been designed to operate their out-
put power stages with pulsating power to reduce power dissipa-
tion and power demand from regulated supplies .Figures 2 and 3
illustrate this technique.The power output stage is only supplied
with enough instantaneous voltage to be able to drive the
required instantaneous signal le vel.The AC reference can be full
wave rectified and applied to the push-pull output drivers since
the output signal is required to be in phase with the AC refer-
ence. The supply voltage will be just a few volts more than the
output signal and internal power dissipation is minimized.
REFERENCE
SOURCE
26V rms 400Hz
1
2
3
4
5
6
7
3.4V rms
21.6V rms
C.T.
D1 D2
D3
D4
C1
C2
+
+
RL' RH'
+V
GND
-V
S1
S2
S3
DIGITAL
INPUT ±15VDC
DSC10510
S1
S1'
S2
S2'
S3
S3'
T1
42359
NOTES:
PARTS LIST FOR 400Hz
D1, D2, D3, D4 = 1N4245
C1 AND C2 = 47µF, 35V DC CAPACITOR
FIGURE 2.TYPICAL CONNECTION DIAGRAM
UTILIZING PULSATING POWER SOURCE FIGURE 3. PULSATING POWER SUPPLY VOLTAGE
WAVEFORMS
+v
- v
+DC SUPPLY LEVEL
-DC SUPPLY LEVEL
POSITIVE PULSATING
SUPPLY VOLTAGE
NEGATIVE PULSATING
SUPPLY VOLTAGE
AMPLIFIER OUTPUT
VOLTAGE ENVELOPE
5
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
THERMAL CONSIDERATIONS
Power dissipation in D/S and D/R circuits is dependent on the
load, whether active (TR) or passiv e (CT or CDX), and the po wer
supply, whether DC or pulsating.With inductive loads virtually all
the power consumed will have to be dissipated in the output
amplifiers.This can require considerable care in heat sinking.
Example:
For illustrative purposes the following thermal calculations are
made using the DSC-10510’s specifications. The DSC-10510
has a 7 VA drive capability for CT, CDX, or TR loads.
Simplest case first: Passive Inductive Load and ±15 Volt DC
power stage supplies (as shown in Figure 2). The power dis-
sipated in the power stage can be calculated by taking the inte-
gral of the instantaneous current multiplied by the voltage differ-
ence from the DC supply that supplies the current and instanta-
neous output voltage over one cycle of the reference. For an
inductive load this is a r ather tedious calculation.Instead take the
difference between the power input from the DC supplies minus
the power delivered to the load. An actual synchro load is highly
inductive with a Q of 4-6; therefore assume that it is purely reac-
tive. The power out, then, is 0 Watts. As a worst case scenario,
also assume the load is the full 7 VA, the converter’s rated load.
The VA delivered to the load is independent of the angle but the
voltage across the synchro varies with the angle from a high of
11.8 Volts line-to-line (L-L) to a low of 10.2 V L-L.The maximum
current therefore is 7VA/10.2 V = 0.68 A rms. The output is L-L
push-pull, that is, all the current flows from the positive supply
out to the load and back to the negative supply. The power input
is the DC voltage times the average current or 30 V x (0.68 A x
0.635/0.707) [avg/rms] = 18.32 Watts.
The power dissipated by the output driver stage is over 18 Watts
shared by the six power transistors. Since one synchro line sup-
plies all the current while the other two share it equally, one will
dissipate 2/3 of the power and the other two will each dissipate
1/3. There are 2 transistors per power stage so each of the two
transistors dissipates 1/3 of the power and the other transistors
dissipate 1/6 of the power. This results in a maximum power in
any one transistor of 1/3 x 18.32 W = 6.04 Watts. The heat rise
from the junction to the outside of the package , assuming a ther-
mal impedance of 4°C per watt = 24.16°C. At an operating case
temperature of 125°C the maximum junction temperature will be
149.16°C.
The other extreme condition to consider is when the output volt-
age is 11.8 V.The current then will be 0.42 Amps and the power
will be 30 x (0.42A x 0.635/0.707) = 11.32 Watts. A similar cal-
culation will show the maximum power per transistor to be 2.3
Watts. This is much less than when the output voltage is 10.2 V.
For Pulsating Supplies the analysis is much more difficult.
Calculations for a purely reactive load with DC supplies equal to
the output voltage peak vs. pulsating supplies with a supply volt-
age equal to the output voltage yield an exact halving of the
power dissipated. At light loads the pulsating supplies approxi-
mate DC supplies and at heavy loads, which is the worst case,
they approximate a pulsating supply as shown in Figure 4.
Advantages of the pulsating supply technique are:
• Reduced load on the regulated ±15 VDC supplies
• Halving of the total power
• Simplified power dissipation management
+15VDC
-15VDC
LIGHT LOAD
HEAVY LOAD
FIGURE 4. LOADED WAVEFORMS
REF IN D/S
R2=1 1/3ΩR1=2/3Ω
REF
ZSO=8.6Ω
NOTES:
R1 + R2 ZSS
3-WIRE SYNCHRO 2-WIRE REF
ACTIVE LOAD
FIGURE 5. EQUIVALENT 2-WIRE CIRCUIT FIGURE 6.TORQUE SYSTEM
R1 R2 R1
R2
REF REF
TORQUE TRANSMITTER TORQUE RECEIVER
6
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
ACTIVE LOAD
Active loads (torque receivers) make it more difficult to calculate
power dissipation.The load is composed of an active part and a
passive part. Figure 5 illustrates the equivalent two wire circuit.
At null, when the torque receiver’s shaft rotates to the angle that
minimizes the current in R2, the po wer dissipated is at its lo w est.
The typical ratio of Zso/Zss = 4.3. For the maximum specified
load of Zss = 2 ohm, the Zso = 2 x 4.3 = 8.6 ohms.Also, the typ-
ical ratio of R2/R1= 2.
In synchro systems with a torque transmitter driving a torque
receiver, the actual line impedances are as shown in Figure 6.
The torque transmitter and torque receiver are electrically identi-
cal, so that the total line impedance is double that of Figure 5.
The torque system is designed to operate this way. The higher
the total line impedances, the lower the current flow at null and
the lower the power dissipation. It is recommended that with
torque loads, discrete resistors be used as shown in Figures 7
and 8.
A torque load is normally at null. Once the torque receiver nulls
at power turn on, the digital commands to the D/S are typically in
smaller angular steps, so the torque system is always at or near
null.Large digital steps, load disturbances, a stuc k torque receiv-
er or one synchro line open, howe v er, cause an off null condition.
At null the load current could be zero (See Figure 9 ). If Vac =
Vab, both in magnitude and phase, then, when “a” is connected
to “b,” no current will flow. Pick C1 and C2 to match the phase
lead of R1 – Zso. In practice this ideal situation is not realized.
The input to output transformation ratio of torque receivers is
specified at 2% and the turns ratio at 0.4%.The in-phase current
flow due to this nominal output voltage (10.2 V) multiplied by the
% error (2.4/100) divided by total resistance (4 Ohms) = 61mA.
A phase lead mismatch between the torque receiver and the
converter of 1 degree results in a quadrature current of 10.2 V x
sin 1°/4 Ohms = 44.5 mA. Total current is the phaser sum 61 +
44.5 = 75.5 mA. Power dissipation is 30 VDC x 75.5 mA rms x
0.9 (avg/rms) = 2.04 Watts. Since this is a light load condition,
even pulsating supplies would be approximating DC supplies.
The off null condition power dissipation is quite different. Actual
synchros hav e no current limiting, so the circuit current is the cur-
rent that the circuit conditions demand.The worst case would be
for a 180 degree error between the two synchros as shown in
Figure 10. For this condition the two equivalent voltage sources
are 10.2 V opposing. The current is (10.2 x 2) / 4 = 5.1 A in
phase.
The power dissipated in the converter is the power supplied by
the ±15 VDC supplies minus the power delivered to the load (30
V x 5.1 A x 0.9) - (10.2 V x 5.1 A) = 87.7 Watts for DC supplies.
This requires a large power supply and high wattage resistors.
The converter output current is typically limited (in the DSC-
10510 case to 0.8 A peak).This limits the power supply to more
reasonable values but introduces another problem – the torque
receiver can hang up in a continuous current limited condition at
a false stable null. The DSC-10510 has special circuits that
sense this continuous current overload condition and sends a
FIGURE 7. D/S EQUIVALENT
REF IN
RH
RL
D/S
2Ω11/3Ω2/3Ω
ZSO=8.6ΩREF
TORQUE LOAD WITH DISCRETE EXTERNAL RESISTOR
1.33Ω
1.33Ω
1.33Ω
S1
S2
S3
RH
RL
S1
S2
S3
D/S TR
REF IN REF
FIGURE 8. D/S - ACTUAL HOOK-UP
2Ω
RH
RL
A
D/S
1 1/3Ω2/3Ω
REF
Zso=8.6Ω
B
C
REF IN
C1
C2
R1
FIGURE 9. IDEAL NULL CONDITION
7
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
momentary 45° “kick” to the torque receiver thus knocking it off
the false null. The torque receiver will then swing to the correct
angle and properly null. If the torque receiver is stuck it will not
be able to swing off the over-current condition. In this case the
converter will send a BIT signal when the case temperature
exceeds 140°C. This BIT signal can be used to shut down the
output power stage.
An additional advantage of using pulsating po wer supplies is that
the loss of reference when driving torque loads is fail safe. The
load will pump up the ±V voltage through the power stage clamp
diodes and the loss of the reference detector will disable the
power stage .The power stage will be turned off with the required
power supply voltages. The pulsating power supply diodes will
isolate the pumped up pulsating supplies from the reference. If
the DC power supplies are to be used for the power stage, and
there is a possibility of the DC supplies being off while the refer-
ence to the torque receiver is on, then the protection circuitry
shown in Figure 11 is highly recommended.
A remote sense feature is incorporated in DDC’s DSC-10510
hybrid digital-to-synchro conver ter. Rated at 7 VA, it offers accu-
racies to ±2 minutes of arc at the load.This remote sense f eature
operates just as other precision sources do. A separate line is
run to each leg of the synchro (in addition to the drive line) to
sense the voltage actually appearing on the load. This is then
used to regulate the output based on load voltage rather than
converter output voltage. This feature is very useful in driving
heavy passive loads in precision systems.
2Ω
D/S
2Ω
10.2V
+15V
10.2V
- 15V
FIGURE 10.WORST CASE 180° ERROR
D/S
+V
-V
+
-V
+15VDC
-15VDC
FIGURE 11. PROTECTION CIRCUITRY
8
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
Data Changing Data Stable
50 nS min. 100 nS min.
50 nS min. 100 nS min.
200 nS min.
200 nS min.
LL
LM
LA
DATA
Bits (9-16)
Bits (1-8)
200 nS min.
LA, LM, LL
Transparent = Hi
Latched = Lo
FIGURE 12B . LL,LM,LATIMING DIAGRAM (8 BIT)
FIGURE 12A. LL,LM,LATIMING DIAGRAM (16 BIT)
200 nS min.
TRANSPARENT
LATCHED
DATA 1-16 BITS
50 nS min. 100 nS min.
Data Changing Data Stable
9
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
0.900
(22.86)
0.018 ±0.002
(0.46 ±0.05)
DIA PIN
SIDE VIEWBOTTOM VIEW
2.14
(54.36) 19 EQ. SP.
0.100 = 1.9
TOL. NONCUM
(2.5 = 48.3)
1.140
(28.96)
0.200 MAX
(5.08)
0.17 MIN
(4.32)
20 21
140
0.120 ±0.002
(3.05 ±0.05)
0.120 ±0.002
(3.05 ±0.05)
Notes:
1. Dimensions are in inches (millimeters).
2. Lead identification numbers for reference only.
3. Lead cluster shall be centered within ±0.10 of outline dimensions.Lead spac-
ing dimensions apply only at seating plane.
4. Pin material meets solderability requirements of MIL-PRF-38534
FIGURE 13. DSC-10510 MECHANICAL OUTLINE
40-PIN TDIP
TABLE 2. DSC-10510 PIN FUNCTIONS
PIN NAME FUNCTION
1DO1 Digital Input 01 (MSB) Logic “1” enables.
2DO2 Digital Input 02
3DO3 Digital Input 03
4DO4 Digital Input 04
5DO5 Digital Input 05
6DO6 Digital Input 06
7DO7 Digital Input 07
8DO8 Digital Input 08
9DO9 Digital Input 09
10 DO10 Digital Input 10
11 DO11 Digital Input 11
12 DO12 Digital Input 12
13 DO13 Digital Input 13
14 DO14 Digital Input 14
15 DO15 Digital Input 15
16 DO16 Digital Input 16 (LSB)
17 RL 26 Vr ms Reference Low Input
18 RH 26 Vr ms Reference High Input
19 S1' Synchro S1 Remote Sense Output
20 S1 Synchro S1 Output
21 S2 Synchro S2 Output
22 S3 Synchro S3 Output
23 +V Power Stage +V
24 -V Power Stage -V
25 S2' Synchro S2 Remote Sense Output
26 S3' Synchro S3 Remote Sense Output
27 NC No Connection
28 GND Ground
29 -15 V Power Supply
30 + 15V Power Supply
31 LA 2nd Latch All Enable. Input enables dual latch.
32 LL 1st Latch LSBs Enable. Enables bits 9 - 16
33 LM 1st Latch MSBs Enable. Enables bits 1 - 8
34 RL' 3.4 Vr ms Reference Low Input
35 RH' 3.4 Vr ms Reference High Input
36 -R (TP) No connection. Factory test point.
37 EN Enable. Power stage enable input allows for digital
shutdown of power stage. Gives complete control
of converter to digital system.
38 BS Battle Shor t Input. Logic 0 overrides over tempera-
ture protection.
39 BIT
Built-In-Test Output. Logic 0 when loss of reference,
loss of ±15 VDC supply, case temperature of
+140°C, or an output over-current has been detect-
ed. Loss of reference, loss of ±15 VDC supply or
case temperature of +140°C will disable the power-
output stage.
40 KKick. Input used for reducing excessive current flow
in torque receiver loads at false null.
16 BIT DIGITAL WORD (Φ) (1 = MSB, 16 = LSB)
1 2 3 4 5 6 7 8 910 11 12 13 14 15 16
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 1
0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1
0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
001 0 1 0 1 0 1 0 1 0 1 0 1 1
0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1
001 1 0 1 0 1 0 1 0 1 0 1 0 1
010 0 0 0 0 0 0 0 0 0 0 0 0 0
010 1 0 1 0 1 0 1 0 1 0 1 0 1
01100 0 0 0 0 0 0 0 0 0 0 0
DEGREES
(HEX)
0° (0000)
15° (0AAB)
30° (1555)
45° (2000)
60° (2AAB)
75° (3666)
90° (4000)
120° (5555)
135° (6000)
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 0 1 0 1 0 1 0 10 1 0 1 0 1 1
1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 0 0 1 0 1 0 1 0 0 0 1 0 1 1
11
1
1 0 1 0 1 0 1 0 1 0 1 0 1
0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1
111 0 0 0 0 0 0 0 0 0 0 0 0 0
111 0 1 0 1 0 1 0 1 0 1 0 1 1
111 1 0 1 0 1 0 1 0 1 0 1 0 1
111 1 1 1 1 1 1 1 1 1 1 1 1 1
180° (8000)
240° (AAAB)
270° (C000)
285° (CAAB)
300° (D555)
315° (E000)
330° (EAAB)
345° (F555)
359° (FFFF)
0
TABLE 3.ANGLES IN DEGREES
CROSS REFERENCED TO A 16-BIT DIGITAL WORD
0
10
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
ORDERING INFORMATION
DSC-10510-XXXX Supplemental Process Requirements:
S = Pre-Cap Source Inspection
L = Pull Test
Q = Pull Test and Pre-Cap Inspection
Blank = None of the Above
Accuracy:
3 = ±4 minutes (No Load) + 1.6 minutes at full Load (7VA Inductive)
4 = ±2 minutes (No Load) + 1.6 minutes at full Load (7VA Inductive)
Process Requirements:
0 = Standard DDC Processing, no Burn-In (See table below.)
1 = MIL-PRF-38534 Compliant
2 = B*
3 = MIL-PRF-38534 Compliant with PIND Testing
4 = MIL-PRF-38534 Compliant with Solder Dip
5 = MIL-PRF-38534 Compliant with PIND Testing and Solder Dip
6 = B* with PIND Testing
7 = B* with Solder Dip
8 = B* with PIND Testing and Solder Dip
9 = Standard DDC Processing with Solder Dip, no Bur n-In (See table below.)
Temperature Grade/Data Requirements:
1 = -55°C to +125°C
2 = -40°C to +85°C
3 = 0°C to +70°C
4 = -55°C to +125°C with Variables Test Data
5 = -40°C to +85°C with Variables Test Data
8 = 0°C to +70°C with Variables Test Data
*Standard DDC Processing with burn-in and full temperature test—see table below.
For DSC-10510 use optional Power Transformer, DDC P/N 42359 (See Figure 2)
For S2 Grounded Applications, use Transformer DDC P/N 42929.
TABLE 11015 (note 1), 1030 (note 2)
BURN-IN
Notes:
1. For Process Requirement "B*" (refer to order ing information), devices may be non-compliant with MIL-
STD-883, Test Method 1015, Paragraph 3.2. Contact factory for details.
2.When applicable.
3000g
2001CONSTANT ACCELERATION C1010TEMPERATURE CYCLE A and C1014SEAL —2009, 2010, 2017, and 2032INSPECTION CONDITION(S)METHOD(S)
MIL-STD-883
TEST
STANDARD DDC PROCESSING
FOR HYBRID AND MONOLITHIC HERMETIC PRODUCTS
11
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
NOTES
12
Data Device Cor poration
www.ddc-web.com DSC-10510
L-05/04-0
NOTES
The information in this data sheet is believed to be accurate; however, no responsibility is
assumed by Data Device Cor poration for its use, and no license or rights are
granted by implication or otherwise in connection therewith.
Specifications are subject to change without notice.
Please visit our web site at www.ddc-web.com for the latest infor mation.
105 Wilbur Place, Bohemia, New Yor k 11716-2482
For Technical Suppor t - 1-800-DDC-5757 ext. 7771
Headquarters, N.Y., U.S.A. - Tel: (631) 567-5600, Fax: (631) 567-7358
Southeast, U.S.A. - Tel: (703) 450-7900, Fax: (703) 450-6610
West Coast, U.S.A. - Tel: (714) 895-9777, Fax: (714) 895-4988
United Kingdom - Tel: +44-(0)1635-811140, Fax: +44-(0)1635-32264
Ireland - Tel: +353-21-341065, Fax: +353-21-341568
France - Tel: +33-(0)1-41-16-3424, Fax: +33-(0)1-41-16-3425
Germany - Tel: +49-(0)8141-349-087, Fax: +49-(0)8141-349-089
Japan - Tel: +81-(0)3-3814-7688, Fax: +81-(0)3-3814-7689
W orld Wide W eb - http://www .ddc-web.com
13
L-05/04-0 PRINTED IN THE U.S.A.
DATA DEVICE CORPORATION
REGISTERED TO ISO 9001
FILE NO. A5976
R
E
G
I
S
T
E
R
E
D
F
I
R
M
®
U
