TSYS02D Digital Temperature Sensor High Accuracy Temperature Sensor 16 bit Resolution High Speed, low Response Time Low Power Consumption 2 I C Interface Small TDFN8 Package DESCRIPTION The TSYS02D is a single chip, temperature sensor. It provides factory calibrated data corresponding to the measured temperature. 2 The data is provided via I C interface. The temperature range is -40C ... +125C while the resolution is 0.01C. 2 The TSYS02D can be interfaced to any microcontroller by an I C interface. The TDFN8 package provides smallest size and very fast time response. FEATURES APPLICATIONS High Accuracy 0.2C @ Temp.: -5C ... +50C Adjustment of high accuracy temperature range on request Low Supply Current < 420A (standby < 0.14A) 2 I C Interface up to 400kHz Small IC-Package TDFN8 2.5mm x 2.5mm Operating Temperature Range: -40C ... +125C TSYS02D Rev 3 www.meas-spec.com 1/8 Industrial Control Replacement of Precision RTDs, Thermistors and NTCs Heating / Cooling Systems HVAC 2013-03 TSYS02D Digital Temperature Sensor ABSOLUTE MAXIMUM RATINGS Absolute maximum ratings are limiting values of permitted operation and should never be exceeded under the worst possible conditions either initially or consequently. If exceeded by even the smallest amount, instantaneous catastrophic failure can occur. And even if the device continues to operate satisfactorily, its life may be considerably shortened. Parameter Supply Voltage Operating Temperature Storage temperature Symbol VDD Top Tstor ESD rating ESD Humidity Hum Conditions Human Body Model (HBM) pin to pin incl. VDD & GND Min -0.3 -40 -55 Typ -2 Max +3.6 +125 +150 Unit V C C +2 kV Non condensing OPERATING CONDITIONS Parameter Operating Supply Voltage Supply Current Standby current Peak Supply Current Conversion time 2 Serial Data Clock I C VDD Capacitor Symbol VDD IDD IS IDD TCONV FSCL Conditions stabilized 1 sample per second No conversion, VDD = 3V T = 25C T = 85C During conversion Min 1.5 Typ Max 3.6 Unit V A 0.14 1.40 A A A ms kHz 18 0.02 0.70 420 43 400 100nF Place close to the chip OPERATIONAL CHARACTERISTICS If not otherwise noted, 3.3V supply voltage is applied. Parameter Temp. Measurement Range Symbol TRANG Accuracy 1 TACC1 Accuracy 2 TACC2 Accuracy 3 TACC2 PSRR Power Supply Reject Ratio Temperature Resolution Self Heating TSYS02D Rev 3 TRES SH1 Conditions -5C < T < +50C VDD = 3.2V - 3.4V -20C < T < +100C VDD = 3.2V - 3.4V -40C < T < +125C VDD = 3.2V - 3.4V VDD = 2.7 - 3.6 T = 25C, C = 100nF 10 samples/s, 60s, still air www.meas-spec.com 2/8 Min -40 Typ Max 125 Unit C -0.2 +0.2 C -0.5 +0.5 C -1.0 +1.0 C 0.1 C 0.01 0.1 C C 2013-03 TSYS02D Digital Temperature Sensor ACCURACY ANALOGUE TO DIGITAL CONVERTER Parameter Resolution Conversion Time Symbol Conditions Min Typ 16 43 Max Unit bit ms Symbol VIH VIL Ileak_25 Ileak_85 CIN Conditions VDD = 1.5...3.6V VDD = 1.5...3.6V T = 25C T = 85C Min 0.7 VDD 0.0 VDD Typ Max VDD 0.3 VDD 0.14 1.40 6 Unit V V Symbol VOH VOL Conditions ISource = 1mA ISink = 1mA Max VDD 0.2 VDD Unit V V tc DIGITAL INPUTS (SCLK, SDA) Parameter Input High Voltage Input Low Voltage Input leakage Current Input Capacitance 0.01 0.25 A pF DIGITAL OUTPUTS (SDA) Parameter Output High Voltage Output Low Voltage TSYS02D Rev 3 www.meas-spec.com 3/8 Min 0.8 VDD 0.0 VDD Typ 2013-03 TSYS02D Digital Temperature Sensor CONNECTION DIAGRAM VDD +3.3V VDD +3.3V TSYS02D PIN FUNCTION TABLE Pin 1 2 3 4 5-8 Name VDD SCL SDA VSS NC Type Power Digital Input Digital Input/Output Power --- Function Supply Voltage 2 I C: Serial Data Clock 2 I C Data Input / Output Ground Not connected / Do not connect INTERFACE DESCRIPTION 2 I C INTERFACE 2 An I C communication message starts with a start condition and it is ended by a stop condition. Each command consists of two bytes: the address byte and command byte. 2 I C ADDRESS 2 The I C address is 0b1000000x. COMMANDS There are four commands: Reset Read PROM (serial number) Read ADC16 Temperature Data (with SCL hold) Read ADC16 Temperature Data (without SCL hold) Command Reset Read ADC16 Temperature Data (with SCL hold) Read ADC16 Temperature Data (without SCL hold) Read first 8 bytes of Serial Number Read last 6 bytes of Serial Number TSYS02D Rev 3 www.meas-spec.com 4/8 Hex Value 0x7E 0x E3 0x F3 0x FA0F 0x FCC9 2013-03 TSYS02D Digital Temperature Sensor RESET SEQUENCE The reset of TSYS02D can be sent at any time. When SDA line is blocked by an undefined state the only way to get the TSYS02D to work is to send a power on reset or several SCL cycles. This is not needed when the last command was not a conversion. CONVERSION AND ADC READ A conversion can be started by sending this command to TSYS02D. When the command is sent to the sensor it stays busy until conversion is done. All other commands except the reset command will not be executed during this time. When conversion is finished the data can be accessed by sending a Read command. If an acknowledge appears from the TSYS02D, you may then send 24 SCLK cycles to get all th result bits. Every 9 bit the system waits for acknowledge. If the acknowledge is not sent the data clocking out of the chip stops. Two types of conversion commands for temperature reading are possible. If the "hold" command is issued, the SCL is held low during conversion, indicating when the conversion is finished. If the "no hold" is issued, the SCL line is not controlled by the TSYS02D. WITH HOLD WITHOUT HOLD TSYS02D Rev 3 www.meas-spec.com 5/8 2013-03 TSYS02D Digital Temperature Sensor READ SERIAL NUMBER FIRST 8 BYTES READ SERIAL NUMBER LAST 6 BYTES TEMPERATURE CALCULATION TEMPERATURE POLYNOMAL ADC16: ADC Result 16 bits T / C = ADC16 / 216 x 175.72 - 46.85 EXAMPLE ADC16: 36636 T / C = 36636 / 216 x 175.72 - 46.85 T / C = 51.38C TSYS02D Rev 3 www.meas-spec.com 6/8 2013-03 TSYS02D Digital Temperature Sensor DIMENSIONS TOP VIEW BOTTOM VIEW SIDE VIEW MARKING Line 1 2 TSYS02D Rev 3 Description Product Name Pin 1 Dot, Date Code YYWW Example TSY2 1244 www.meas-spec.com 7/8 2013-03 TSYS02D Digital Temperature Sensor ORDER INFORMATION The TSYS02 temperature sensor family compromises currently three different solutions. Further customer specific adaptations are available on request. Please refer to the table below for part name, description and order information. Part Name TSYS02D TSYS02P TSYS02S Description Digital Temperature Sensor, TDFN8, I2C Interface Digital Temperature Sensor, TDFN8, PWM Interface Digital Temperature Sensor, TDFN8, SDM Interface Order Number G-NIMO-003 G-NIMO-004 G-NIMO-005 EMC Due to the use of these modules for OEM application no CE declaration is done. Especially line coupled disturbances like surge, burst, HF etc. cannot be removed by the module due to the small board area and low price feature. There is no protection circuit against reverse polarity or over voltage implemented. The module will be designed using capacitors for blocking and ground plane areas in order to prevent wireless coupled disturbances as good as possible. DEFINITIONS AND DISCLAIMERS Application information - Applications that are described herein for any of these products are for illustrative purpose only. MEAS Deutschland GmbH makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Life support applications - These products are not designed for use in life support appliances, devices, or systems where malfunctions of these products can reasonably be expected to result in personal injury. MEAS Deutschland GmbH customers using or selling this product for use in such applications do so at their own risk and agree to fully indemnify MEAS Deutschland GmbH for any damages resulting from such improper use or sale. TECHNICAL CONTACT INFORMATION NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc. 910 Turnpike Road Shrewsbury, MA 01545 Tel: 1-508-842-0516 Fax: 1-508-842-0342 MEAS Deutschland GmbH Hauert 13 44277 Dortmund Tel: +49 (0) 231/9740-0 Fax: +49 (0) 231/9740-20 Measurement Specialties (China) Ltd. No. 26 Langshan Road Shenzhen High-Tech Park (North) Nanshan District, Shenzhen 518057, China Tel: +86 (0) 755 33305088 Fax: +86 (0) 755 33305099 Sales email: temperature.sales.amer@measspec.com Sales email: info.de@meas-spec.com Sales email: temperature.sales.asia@meas-spec.com The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer's technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others. TSYS02D Rev 3 www.meas-spec.com 8/8 2013-03