ALUMINUM ELECTROLYTIC CAPACITORS WX 5.5mmL Chip Type series Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Load life of 2000 hours at 85C. WT Compliant to the RoHS directive (2011/65/EU). WJ High Temperature High Temp reflow WX Bi-polarized WP Smaller Specifications ZS Item Performance Characteristics Category Temperature Range -40 to +85C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 330F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (A) ,whichever is greater. Tangent of loss angle (tan ) Rated voltage (V) tan (MAX.) 6.3 10 16 25 0.35 (0.40) 0.26 (0.30) 0.20 (0.24) 0.16 (0.19) 0.14 (0.16) 4 7 15 Rated voltage (V) Z- 25C / Z+20C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Measurement frequency : 120Hz at 20C 35 50 4 Z- 40C / Z+20C 6.3 4 8 0.12 (0.14) 0.12 (0.14) Values in ( ) applicable to WR, 3 case size. Measurement frequency : 120Hz 16 25 35 50 2 2 2 2 4 4 3 3 10 3 8 Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 85C. Shelf Life After storing the capacitors under no load at 85C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20C. Marking Black print on the case top. Chip Type Positive 5.4 5.4 +0.1 -0.2 +0.1 -0.2 C0.2 C0.2 Positive E E B0.2B0.2 X2A2 10 10 16V 16V 2 Lot No. Plastic platform 0.3 MAX. 1 Voltage Plastic platform 0.3 MAX. 0.5 to 0.8 A D BA C B E C 3 1.5 3 3.3 1.5 3.3 3.3 0.8 3.3 4 1.8 4 4.3 1.8 4.3 4.3 1.0 4.3 Within 10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 16V 10F) 1 2 3 4 5 6 7 8 5 2.1 5 5.3 2.1 5.3 5.3 1.3 5.3 Negative (mm) 6.3 (mm) 8 2.4 6.3 3.3 8 6.6 2.4 8.3 3.3 6.6 8.3 6.6 8.3 2.2 6.6 2.3 8.3 9 10 11 12 13 14 2 X 3 1 4 C 5 1 6 0 7 0 8 M 9 C 10 L 11 1 12 G 13 B 14 U1 W UWX 1 C 1 0 0 MC L 1 G B Taping code Taping code Size code Configuration Configuration Capacitance toleranc (20%) Capacitance tolerance (20%) Rated capacitance (10F) RatedRated capacitance voltage(10F) (16V) Negative 0.5 to 0.8 D Capacitance change tan Leakage current A0.2A0.2 A0.2 A0.2 1 Voltage D0.5 D0.5 Capacitance 2 Lot No. 0.5 MAX. 0.5 MAX. Capacitance Within 20% of the initial capacitance value (Within 25% for 4 V and 3,WR series units) 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan Leakage Current D Size code Code 3 D 4 to 38 2 Code 12 4 to 8 1 Rated Series voltagename (16V) Series name Type Type * In the case of size 3 in ( ),parentheses, use WX in the 2nd and 3rd digit and put a 2 in the 12th digit of type numbering system. 1. Voltage mark for 6.3V is 6V . E 0.8 1.0 1.3 2.2 2.3 In case of marking for 3 units, "V" for rated voltage is omitted. 1. Voltage mark for 6.3V is 6V . 2. In case of marking for 3 units, Lot No.is expressed by a digit (month code). In case of marking for 3 units, "V" for rated voltage is omitted. 2. In case of marking for 3 units, Lot No.is expressed by a digit (month code). Dimension table in next page. CAT.8100D ALUMINUM ELECTROLYTIC CAPACITORS WX series Dimensions 4 0G V Cap. (F) Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 0.1 0R1 4 (3) 1.0 0.22 R22 4 (3) 2.0 0.33 R33 4 (3) 2.8 0.47 R47 4 (3) 4.0 1 010 4 (3) 8.4(8.0) 2.2 2R2 4 (3) 13 (10) 3.3 3R3 4.7 4R7 10 100 22 220 3 019 4 (3) 28 (21) 5 33 330 4 028 5 37 (34) 47 470 4 033 5 56 560 5 042 100 101 5 056 150 151 6.3 079 6.3 220 221 6.3 096 8 110 (74) 330 331 8 145 8 170 3 3 10 4 17 4 (3) 16 (12) 4 18 5 20 (18) 4 (3) 23 (18) 5 27 (24) 5 29 (24) 6.3 33 (30) 33 (30) 5 37 (30) 6.3 42 (38) 6.3 46 (39) 8 52 (43) 5 41 (34) 6.3 49 (44) 6.3 52 (46) 8 62 (53) 8 71 45 (40) 6.3 52 (47) 6.3 58 (52) 8 70 (60) 8 80 6.3 52 (46) 6.3 57 (50) 6.3 63 (57) 8 6.3 70 (47) 6.3 76 (54) 6.3 86 8 71 8 111 (76) 8 135 76 (65) 110 ( ) is also available with 3mm upon request. * In the case of size 3 in ( ),parentheses, use WX at 2nd and 3rd digit and put 2 at the 12th digit of type numbering system. Size 4 is available for capacitors marked. " " Size 5 is available for capacitors marked. " " Size 6.3 is available for capacitors marked. " " 8.4 } Case size Rated D (mm) ripple Rated ripple current (mArms) at 85C 120Hz ( ) = 3 units and WR Series In such a case, W R will be put at 2nd and 3rd digit of type numbering system. Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UR(p.150), UG(p.158) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Nichicon: UWP1V4R7MCL1GB UWR1E220MCL1GB UWR1A470MCL1GB UWR1C470MCL1GB UWR1E100MCL1GB UWR1H220MCL1GB UWR0J470MCL1GB UWR1V100MCL1GB UWR0J101MCL1GB UWR0J221MCL1GB UWR0J330MCL1GB UWR1A151MCL1GB UWR1A220MCL1GB UWR1A330MCL1GB UWR1A560MCL1GB UWR1C220MCL1GB UWR1C330MCL1GB UWR1E330MCL1GB UWR1E470MCL1GB UWR1E560MCL1GB UWR1H100MCL1GB UWR1H4R7MCL1GB UWR1V220MCL1GB