DRD1360D14
Rectifier Diode
DS5991 – 1 March 2011 (LN28177)
1/6
www.dynexsemi.com
FEATURES
Double Side Cooling
High Surge Capability
VOLTAGE RATINGS
Part and
Ordering
Number
Repetitive Peak
Voltages
VRRM
V
Conditions
DRD1360D14
DRD1360D12
DRD1360D10
DRD1360D08
DRD1360D06
1400
1200
1000
800
600
VRSM = VRRM+100V
ORDERING INFORMATION
When ordering, select the required part number
shown in the Voltage Ratings selection table.
For example:
DRD1360D14 for a 1400V device
KEY PARAMETERS
VRRM 1400V
IF(AV) 1360A
IFSM 15200A
(See Package Details for further information)
Fig. 1 Package outline
DRD1360D14
2/6
www.dynexsemi.com
CURRENT RATINGS
Tcase = 75°C unless stated otherwise
Symbol
Test Conditions
Max.
Units
Double Side Cooled
IF(AV)
Mean forward current
Half wave resistive load
1600
A
IF(RMS)
RMS value
-
2510
A
IF
Continuous (direct) on-state current
-
2260
A
Tcase = 100°C unless stated otherwise
Symbol
Test Conditions
Max.
Units
Double Side Cooled
IF(AV)
Mean forward current
Half wave resistive load
1360
A
IF(RMS)
RMS value
-
2140
A
IF
Continuous (direct) on-state current
-
1920
A
SURGE RATINGS
Symbol
Parameter
Test Conditions
Max.
Units
IFSM
Surge (non-repetitive) on-state current
10ms half sine, Tcase = 190°C
15.2
kA
I2t
I2t for fusing
VR = 0
1.16
MA2s
- 3 -
DRD1360D14
3/6
www.dynexsemi.com
THERMAL AND MECHANICAL RATINGS
Symbol
Test Conditions
Min.
Max.
Units
Rth(j-c)
Double side cooled
DC
-
0.035
°C/W
Rth(c-h)
Double side cooled
DC
-
0.01
°C/W
Tvj
Blocking VDRM / VRRM
-40
190
°C
Tstg
-40
190
°C
Fm
8
12
kN
CHARACTERISTICS
Symbol
Parameter
Test Conditions
Min.
Max.
Units
VFM
Forward voltage
At 1500A peak, Tcase = 25°C
-
1.30
V
IRM
Peak reverse current
At VDRM, Tcase = 190°C
-
50
mA
QS
Total stored charge
IF = 1000A, dIRR/dt =10A/µs
-
2000
µC
Tcase = 190°C, VR =100V
VTO
Threshold voltage
At Tvj = 190°C
-
0.78
V
rT
Slope resistance
At Tvj = 190°C
-
0.257
m
DRD1360D14
4/6
www.dynexsemi.com
CURVES
Fig.2 Maximum forward characteristics
Fig.3 Dissipation curves
Fig.4 Surge (Non-Repetitive) Forward current vs time
Fig.5 Maximum (limit) transient thermal impedance-
junction to case
0
1000
2000
3000
4000
5000
6000
7000
8000
0 1 2 3
Instantaneous forward current, IF- (A)
Instantaneous forward voltage,VF- (V)
Tj=190°C
0
200
400
600
800
1000
1200
1400
1600
1800
0200 400 600 800 1000 1200 1400
Mean power dissipation - (W)
Mean on-state current, IT(AV) - (A)
1/2 wave
3 phase
6 phase
4.0
6.0
8.0
10.0
12.0
14.0
16.0
110 100
Surge current, ITSM - (KA)
Number of cycles
Conditons:
Tcase=190°C
VR=0
Pulse width = 10ms
0
0.01
0.02
0.03
0.04
0.001 0.01 0.1 1 10 100
Thermal Impedance Zth(j-c) (°C/W)
Time ( s )
Double side cooled
- 5 -
DRD1360D14
5/6
www.dynexsemi.com
PACKAGE DETAILS
For further package information, please contact Customer Services. All dimensions in mm, unless stated otherwise.
DO NOT SCALE.
Package outline type code: D
Note:
Some packages may be supplied with gate and or tags.
DRD1360D14
6/6
www.dynexsemi.com
IMPORTANT INFORMATION:
This publication is provided for information only and not for resale.
The products and information in this publication are intended for use by appropriately trained technical personnel.
Due to the diversity of product applications, the information contained herein is provided as a general guide only and does not constitute
any guarantee of suitability for use in a specific application.The user must evaluate the suitability of the product and the completeness of
the product data for the application. The user is responsible for product selection and ensuring all safety and any warning requirements
are met. Should additional product information be needed please contact Customer Service.
Although we have endeavoured to carefully compile the information in this publication it may contain inaccuracies or typographical
errors. The information is provided without any warranty or guarantee of any kind.
This publication is an uncontrolled document and is subject to change without notice. When referring to it please ensure that it is the
most up to date version and has not been superseded.
The products are not intended for use in applications where a failure or malfunction may cause loss of life, injury or damage to property.
The user must ensure that appropriate safety precautions are taken to prevent or mitigate the consequences of a product failure or
malfunction.
The products must not be touched when operating because there is a danger of electrocution or severe burning. Always use
protective safety equipment such as appropriate shields for the product and wear safety glasses. Even when disconnected any
electric charge remaining in the product must be discharged and allowed to cool before safe handling using protective gloves.
Extended exposure to conditions outside the product ratings may affect reliability leading to premature product failure. Use outside the
product ratings is likely to cause permanent damage to the product. In extreme conditions, as with all semiconductors, this may include
potentially hazardous rupture, a large current to flow or high voltage arcing, resulting in fire or explosion. Appropriate application design
and safety precautions should always be followed to protect persons and property.
Product Status & Product Ordering:
We annotate datasheets in the top right hand corner of the front page, to indicate product status if it is not yet fully approved for
production. The annotations are as follows:-
Target Information: This is the most tentative form of information and represents a very preliminary specification.
No actual design work on the product has been started.
Preliminary Information: The product design is complete and final characterisation for volume production is in
progress.The datasheet represents the product as it is now understood but details may change.
No Annotation: The product has been approved for production and unless otherwise notified by Dynex any
product ordered will be supplied to the current version of the data sheet prevailing at the
time of our order acknowledgement.
All products and materials are sold and services provided subject to Dynex’s conditions of sale, which are available on request.
Any brand names and product names used in this publication are trademarks, registered trademarks or trade names of their
respective owners.
HEADQUARTERS OPERATIONS
DYNEX SEMICONDUCTOR LIMITED
Doddington Road, Lincoln, Lincolnshire, LN6 3LF
United Kingdom.
Phone: +44 (0) 1522 500500
Fax: +44 (0) 1522 500550
Web: http://www.dynexsemi.com
CUSTOMER SERVICE
Phone: +44 (0) 1522 502753 / 502901
Fax: +44 (0) 1522 500020
e-mail: power_solutions@dynexsemi.com
Dynex Semiconductor Ltd. Technical Documentation – Not for resale.