UMBER TYPE GS-12-675 PRODUCT SPECIFICATION TITLE PAGE 1.25 mm pitch SMT Wire to Board Connector REVISION 1 of 7 AUTHORIZED BY A DATE Jason Hsu 11/9/10 CLASSIFICATION UNRESTRICTED 1.0 SCOPE This specification covers performance, tests and quality requirements for 1.25 mm pitch Wire to Board DIP & SMT Type of 10114826~10114831 Series. 2.0 REFERENCE DOCUMENTS EIA-364 ELECTRONICS INDUSTRIES ASSOCIATION 3.0 DEFINITIONS 3.1 Design and Construction Product shall be of design, construction and physical dimensions specified on applicable product drawing. All materials conform to RoHS 3.2 Materials and Finish 3.2.1 Contact: Copper alloy Finish: (a) Contact Area: Based on drawing specification. (b) Under plate: Nickel-plated all over. (c) Solder area: Based on drawing specification. 3.2.2 Housing: Thermoplastic or Thermoplastic High Temp., UL94V-0 and meet IEC 60695-2 glowing/hot wire test. 3.2.3 M.H.D: Copper Alloy, Plating based on drawing specification. 3.3 Ratings 3.3.1 3.3.2 4.0 Voltage: 125 Volts AC (per pin) Current: 1 Amp (0.8 A --32 AWG) REQUIREMENTS 4.1 Test Requirements and Procedures Summary Item Examination of Product Requirement Standard Product shall meet requirements Visual, dimensional and functional of applicable product drawing per applicable quality inspection and specification. plan. ELECTRICAL Item Low-signal Level Contact Resistance PDS: Rev :A Requirement 20 m Max.(initial)per contact 40 m Max. after test STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A Standard Mate connectors, measure by dry circuit, 20mV Max., 100mA Max. (EIA-364-23) Printed: Apr 05, 2012 UMBER TYPE GS-12-675 PRODUCT SPECIFICATION TITLE PAGE 1.25 mm pitch SMT Wire to Board Connector REVISION 2 of 7 AUTHORIZED BY Jason Hsu A DATE 11/9/10 CLASSIFICATION UNRESTRICTED Insulation Resistance Dielectric Withstanding Voltage Unmated connectors, apply 500 V DC between adjacent terminals. (EIA-364-21) 500 VAC Min. at sea level Test between adjacent contacts of for 1 minute. unmated connectors. No discharge, flashover or (EIA-364-20) breakdown. Current leakage: 1 mA max. 100 M Min. MECHANICAL Item Requirement Durability 30 cycles. Insertion/Withdrawal Force See Section 7. Contact Retention Force 0.5kgf MIN. Hold down /Housing Retention Force 1.0kgf MIN. Wire Retention Force 0.5kgf MIN. Terminal / Housing Retention Force 0.5kgf MIN. PDS: Rev :A Standard The sample should be mounted in the tester and fully mated and unmated the number of cycles specified at the rate of 25.4 3mm/min. (EIA-364-09) Operation Speed 25.4 3 mm/minute.. Measure the force required to mate/Unmate connector. (EIA-364-13) Apply axial pull out force at the speed rate of 25.4 3 mm/minute. On the terminal assembled in the housing. Apply axial pull out force at the speed rate of 25.4 3 mm/minute. On the hold down assembled in the housing. Apply axial pull out force at the speed rate of 25.4 3 mm/minute. On the terminal assembled in the housing. Apply axial pull out force at the speed rate of 25.4 3 mm/minute. On the terminal assembled in the housing. STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A Printed: Apr 05, 2012 UMBER TYPE GS-12-675 PRODUCT SPECIFICATION TITLE PAGE 1.25 mm pitch SMT Wire to Board Connector REVISION 3 of 7 AUTHORIZED BY Jason Hsu A DATE 11/9/10 CLASSIFICATION UNRESTRICTED Vibration The electrical load condition shall be 100 mA maximum for all contacts. Subject to a simple harmonic motion having amplitude of 0.76mm (1.52mm maximum total excursion) in frequency between the limits of 10 and 55 Hz. The entire frequency range, from 10 to 55 Hz and return to 10 Hz, shall be traversed in approximately 1 minute. This motion shall be applied for 2 hours in each of three mutually perpendicular directions. (EIA-364-28 Condition I) 1 s Max. Shock (Mechanical) Subject mated connectors to 50 G's (peak value) half-sine shock pulses of 11 milliseconds duration. Three shocks in each direction shall be applied along the three mutually perpendicular axes of the test specimen (18 shocks). The electrical load condition shall be 100mA maximum for all contacts. (EIA-364-27, test condition A) 1 s Max. ENVIRONMENTAL Item Resistance to Reflow Soldering Heat Resistance to Hand Soldering Heat Thermal Shock Humidity PDS: Rev :A Requirement See Product Qualification and Test Sequence Group 9 (Lead Free) Excessive pressure shall not be applied to the terminals. See Product Qualification and Test Sequence Group 10 Standard Pre Heat150~180, 60~90sec. Heat230 Min., 40sec Min. Peak Temp.260Max, 10sec Max. Soldering iron35010 Duration3~4 sec. at least Mate module and subject to follow condition for 5 cycles. See Product Qualification and 1 cycles: -40 +0/-3 , 30 minutes Test Sequence Group 3 +85 +3/-0 , 30 minutes (EIA-364-32, test condition A) Mated Connector See Product Qualification and 40, 90~95% RH, 96 hours Test Sequence Group 3 (EIA-364-31, test condition A) STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A Printed: Apr 05, 2012 UMBER TYPE GS-12-675 PRODUCT SPECIFICATION TITLE PAGE 1.25 mm pitch SMT Wire to Board Connector REVISION 4 of 7 AUTHORIZED BY Jason Hsu A DATE 11/9/10 CLASSIFICATION UNRESTRICTED Subject mated connectors to See Product Qualification and temperature life at 105 for 96 hours. Temperature life Test Sequence Group 4 Measure Signal. (EIA-364-17, Test condition A) Subject mated/unmated connectors to See Product Qualification and 5% salt-solution concentration, 35 for Salt Spray Test Sequence Group 5 48 hours. (EIA-364-26, Test condition B) Solder able area shall have And then into solder bath, Temperature Solder ability minimum of 95% solder at 245 5 , for 4-5 sec. coverage. Note. Flowing Mixed Gas shell be conduct by customer request. 5.0 5.1 INFRARED REFLOW CONDITION Lead-Free Process PDS: Rev :A STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A Printed: Apr 05, 2012 UMBER TYPE PRODUCT SPECIFICATION GS-12-675 TITLE PAGE REVISION 1.25 mm pitch SMT Wire to Board Connector 5 of 7 A AUTHORIZED BY DATE Jason Hsu 11/9/10 CLASSIFICATION UNRESTRICTED 6.0 PRODUCT QUALIFICATION AND TEST SEQUENCES Test Group Test or Examination 1 2 3 4 5 6 7 8 9 10 17 16 14 1 1 15 14 210 29 25 3 Test Sequence Examination of Product Low-signal Level Contact Resistance Insulation Resistance 39 38 Dielectric Withstanding Voltage 48 47 Insertion / Withdrawal Force 24 Durability 3 Contact Retention Force (Wafer) 1 Vibration(Random) / Vibration 2 Shock (Mechanical) 3 Thermal Shock 5 Humidity 6 Temperature life 5 Salt Spray 3 Solder ability 1 Wire Retention Force 1 Terminal / Housing Retention Force 2 Metal Hold-Down /Housing Retention Force 2 Resistance to Reflow Soldering Heat 2 Resistance to Hand Soldering Heat Sample Size PDS: Rev :A 2 4 4 4 STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A 4 4 2 4 4 4 4 Printed: Apr 05, 2012 UMBER TYPE PRODUCT SPECIFICATION GS-12-675 TITLE PAGE 1.25 mm pitch SMT Wire to Board Connector REVISION 6 of 7 A AUTHORIZED BY DATE Jason Hsu 11/9/10 CLASSIFICATION UNRESTRICTED 7.0 INSERTION / WITHDRAWAL FORCE No of CKT Insertion Force ( Kgf, Max ) 1st 6th Withdrawal Force (Kgf, Min ) 30th 1st 6th 30th 2 2.00 1.80 1.60 0.28 0.23 0.18 3 2.50 2.30 2.10 0.30 0.25 0.20 4 3.00 2.80 2.60 0.33 0.28 0.23 5 3.50 3.30 3.10 0.38 0.33 0.28 6 4.00 3.80 3.60 0.43 0.38 0.33 7 4.50 4.30 4.10 0.48 0.43 0.38 8 5.00 4.80 4.60 0.53 0.48 0.43 9 5.50 5.30 5.10 0.56 0.51 0.46 10 6.00 5.80 5.60 0.59 0.54 0.49 11 6.50 6.30 6.10 0.62 0.57 0.52 12 7.00 6.80 6.60 0.65 0.60 0.55 13 7.50 7.30 7.10 0.68 0.63 0.58 14 8.00 7.80 7.60 0.71 0.66 0.61 15 8.50 8.30 8.10 0.74 0.69 0.64 PDS: Rev :A STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A Printed: Apr 05, 2012 UMBER TYPE PRODUCT SPECIFICATION GS-12-675 TITLE PAGE 1.25 mm pitch SMT Wire to Board Connector REVISION 7 of 7 AUTHORIZED BY Jason Hsu A DATE 11/9/10 CLASSIFICATION UNRESTRICTED RECORD RETENTION Revision Page A ALL PDS: Rev :A Description New release STATUS:Released Copyright FCI. Form E-3701 - Revision B GS-01-029 - Revision A ECR No. Date T10-0090 11/09/2010 Printed: Apr 05, 2012 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI / Amphenol: 10114828-11108LF