TS9010 Series 150mA CMOS LDO with Enable SOT-25 Pin Definition: 1. Ground 2. Input 3. Enable 4. N/C 5. Output General Description The TS9010 series is combine high accuracy with very low power consumption, providing high output current even when the application requires very low dropout voltage. The Chip Enable (CE) includes a CMOS or TTL compatible input allows the output to be turned off to prolong battery life. The TS9010 series is included a precision voltage reference, error correction circuit, a current limited output driver and over temperature shutdown. This series are offered in 5-pin SOT-25 package. Features Dropout voltage typically 0.4V @Io=150mA (Vo=5V) Output current up to 150mA (Vout=3V) Low power consumption Output voltage 2% Internal current limit Thermal shutdown protection Ordering Information Part No. Applications Package Packing TS9010xCX5 RF SOT-25 3Kpcs / 7" Reel Note: Where x denotes voltage option, available are A= 1.5V D= 1.8V, K= 2.5V, S= 3.3V, 5= 5.0V. Contact factory for additional voltage options. Palmtops Video recorders Battery powered equipment PC peripherals High-efficiency linear power supplies Digital signal camera Typical Application Circuit Block Diagram CE (pin 3) may be connected directly to Vin (pin 2) 1/6 Version: A07 TS9010 Series 150mA CMOS LDO with Enable Absolute Maximum Rating (Note 1) Parameter Symbol Limit Unit Input Supply Voltage Vin +12 V Enable Input Voltage Vce 0 ~ Vin+0.3 V Output Current Io 200 mA Power Dissipation (Note 3) PD 380 Thermal Resistance Operating Junction Temperature Range Storage Temperature Range mW o ja 220 Tj -40 ~ +125 o -65 ~ +150 o TSTG o Lead Soldering Temperature (260 C) C/W C C 5 S Recommend Operating Rating (Note 2) Input Supply Voltage Vin +10 V Enable Input Voltage Vce Gnd-0.3 ~ Vin+0.3 V Electrical Characteristics (Ta = 25oC, Cout=2.2uF, Vce2V, unless otherwise noted.) Parameter Output Voltage Conditions Vin=Vo + 1V, Io= 40mA Coefficient (Note 4) Vo+1V Vin Vo+2V, Io=1mA Vin=Vo+1V, Load Regulation (Note 5) Vo 2.5V 1mAIL150mA Typ 0.98|Vo| Output Voltage Temperature Line Regulation Min Max Unit 1.02|Vo| V o -- 100 -- ppm/ C -- 0.2 0.3 %/V -- 30 80 mV Vin=Vo+1V, Vo< 2.5V -- 40 90 Io=80mA -- 200 400 Io=150mA -- 400 700 Quiescent Current Vin0.4V (shutdown) -- 0.01 1 uA Ground Pin Current (Note 7) Vin=Ven=Vo+1V -- -- 19 uA Vin=Vo+1V, Ven=Gnd -- -- 0.1 Output Current Limit Vout=0V -- 300 -- mA Power Supply Rejection Ratio At f=100Hz, Io=0.1mA, -- 45 -- dB -- 0.05 -- %/W 1mAIL80mA Dropout Voltage (Note 6) Thermal Regulation (Note 8) 2/6 mV Version: A07 TS9010 Series 150mA CMOS LDO with Enable Electrical Characteristics (continued) Min Typ Max Unit -- -- 0.25 V 1.5 -- -- V Vce=Vin -- -- 1 Vce=Gnd 0.2 0.05 0 Parameter Conditions Enable Input Enable Input Logic-Low Voltage Regulation shutdown Enable Input Logic-High Voltage Regulation enable Enable Input Current uA Notes: a. Exceeding the absolute maximum rating may damage the device. b. The device is not guaranteed to function outside its operating rating. c. The maximum allowable power dissipation at any Ta is Pd(max) = [ Tj(max) - Ta] * ja. Exceeding the maximum allow able power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. d. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. e. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 1mA to 150mA(Vout>2.5V) and 1mA to 80mA(Vout<2.5V). Changes in output voltage due to heating effects are covered by the thermal regulation specification. f. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. g. Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. h. Thermal regulation is defined as the change in output voltage at a time "t" after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 150mA load pulse at Vin=12V for t=10mS. 3/6 Version: A07 TS9010 Series 150mA CMOS LDO with Enable Application Examples Standard Circuit Typical Application Circuit 2 4/6 Version: A07 TS9010 Series 150mA CMOS LDO with Enable SOT-25 Mechanical Drawing DIM A+A1 B C D E E H L 1 S1 5/6 SOT-25 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX. 0.09 1.25 0.0354 0.0492 0.30 0.50 0.0118 0.0197 0.09 0.25 0.0035 0.0098 2.70 3.10 0.1063 0.1220 1.40 1.80 0.0551 0.0709 1.90 BSC 0.0748 BSC 2.40 3.00 0.09449 0.1181 0.35 BSC 0.0138 BSC 0 10 0 10 0.95 BSC 0.0374 BSC Version: A07 TS9010 Series 150mA CMOS LDO with Enable Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC's terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 6/6 Version: A07