ALUMINUM ELECTROLYTIC CAPACITORS UD Chip Type, Low Impedance series Chip type, low impedance temperature range up to +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). WD High Temp reflow CD UD Low Impedance WG Low Impedance Specifications Performance Characteristics Item Category Temperature Range -55 to +105C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1500F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (A), whichever is greater. Measurement frequency : 120Hz at 20C 10 16 25 35 50 Rated voltage (V) 6.3 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) tan (MAX.) Tangent of loss angle (tan ) ( ) is 8 over Measurement frequency : 120Hz 6.3 3 5 Rated voltage (V) Z- 25C / Z+20C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z- 55C / Z+20C 10 2 4 The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 5000 hours (2000 hours for D = 4, 5 and 6.3) at 105C. Endurance 25 2 3 16 2 4 35 2 3 Capacitance change tan Leakage current 50 2 3 Within 30% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within 10% of the initial capacitance value maintained at 250C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Chip Type Type numbering system (Example : 16V 22F) (4 to 6.3) H 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Package code A0.2 A0.2 0.5 MAX. UUD 1 C 2 2 0 M C L 1 GS E L0.3 Capacitance Lot No. C0.2 B0.2 D0.5 Series A2 22C UD Voltage (C:16V) Positive Plastic platform 0.3 MAX. Configuration D 4 to 6.3 Rated capacitance (22F) 8 * 10 Rated voltage (16V) Capacitance tolerance (20%) Negative Code CL NL Series name Type (8 to 10 ) Lot No. 10 A 16 C 25 E 35 V 0.5 MAX. (mm) DxL A0.2 A0.2 E L0.5 Capacitance Negative Pressure relief vent Voltage V 6.3 j Code C0.2 B0.2 A2 100V UD Trade mark Plastic platform 0.3 MAX. Series D0.5 Voltage (V:35V) Positive A B C E L H 4 x 5.8 5 x 5.8 6.3 x 5.8 6.3 x 7.7 8 x 10 10 x 10 1.8 4.3 4.3 1.0 5.8 0.5 to 0.8 2.1 5.3 5.3 1.3 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 2.9 8.3 8.3 3.1 10 0.8 to 1.1 3.2 10.3 10.3 4.5 10 0.8 to 1.1 H 50 H Dimension table in next page. CAT.8100D ALUMINUM ELECTROLYTIC CAPACITORS UD series Dimensions Cap. (F) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 x 5.8 5.00 30 2.2 2R2 4 x 5.8 5.00 30 3.3 3R3 4 x 5.8 5.00 30 4.7 4R7 10 100 15 150 22 220 27 270 4 x 5.8 1.80 33 330 5 x 5.8 47 470 56 4 x 5.8 1.80 80 5 x 5.8 1.52 85 4 x 5.8 1.80 80 5 x 5.8 0.76 150 6.3 x 5.8 0.88 165 4 x 5.8 1.80 80 5 x 5.8 0.76 150 5 x 5.8 0.76 150 6.3 x 5.8 0.88 165 4 x 5.8 1.80 80 5 x 5.8 0.76 150 5 x 5.8 0.76 150 5 x 5.8 0.76 150 6.3 x 5.8 0.88 165 80 5 x 5.8 0.76 150 5 x 5.8 0.76 150 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.68 185 0.76 150 5 x 5.8 0.76 150 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.68 185 5 x 5.8 0.76 150 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.68 185 560 5 x 5.8 0.76 150 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.34 280 8 x 10 0.34 300 68 680 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.34 280 8 x 10 0.34 300 100 101 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.34 280 8 x 10 0.17 450 8 x 10 0.34 300 150 151 6.3 x 5.8 0.44 230 6.3 x 5.8 0.44 230 6.3 x 7.7 0.34 280 8 x 10 0.17 450 8 x 10 0.17 450 10 x 10 0.18 670 220 221 6.3 x 5.8 0.44 230 6.3 x 7.7 0.34 280 6.3 x 7.7 0.34 280 8 x 10 0.17 450 8 x 10 0.17 450 10 x 10 0.18 670 330 331 6.3 x 7.7 0.34 280 8 x 10 0.17 450 8 x 10 0.17 450 8 x 10 0.17 450 10 x 10 0.09 670 470 471 8 x 10 0.17 450 8 x 10 0.17 450 8 x 10 0.17 450 10 x 10 0.09 670 680 681 8 x 10 0.17 450 10 x 10 0.09 670 10 x 10 0.09 670 1000 102 8 x 10 0.17 450 10 x 10 0.09 670 1500 152 10 x 10 0.09 670 Case size D x L (mm) Impedance Rated ripple Max. Impedance () at 20C 100kHz, Rated ripple current (mArms) at 105C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Nichicon: UUD1V221MNQ1GS