TRIMPOT® POTENTIOMETER
PANEL MOUNTING OPTIONS AND
HARDWARE
Many Trimpot® Potentiometers are
available for panel mount application.
This product option provides for
maximum design exibility.
To order Trimpot® Potentiometers with
panel mount hardware attached by the
factory, simply add an “M” or “Z”
sufx to the Bourns part number per
Table I.
Example:
3006P-1-100Z
To order military Trimpot® Potentiom-
eters with panel mount hardware
attached by the factory, order the
military part number and add “with panel
mount attached.”
Example:
RT12C2PRC, with panel mount
attached.
To order panel mounting accessories for
customer installation, simply use the part
number per Table II.
Example:
H83P
NOTE: For complete product specica-
tions, see data sheet for the trimmer
model.
Torque - Apply maximum 8 in. lbs.
on mounting nut when mounted on
panel.
Models RT12/RJ12, 3057/3059 Models 3005/3006/3009
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
Factory Installed Panel Mount
6.76 ± .38
(.266 ± .015)
3.81
(.150)
HEX NUT AND
LOCKWASHER
10.31
(.406)
7.95
(.313) 33.35
(1.31)
6.35
(.25)
1.52 TO 3.30
(.06 TO .13)
BUSHING
10-32
NF-2 THD
5.94
(.234)
ADJ. SLOT
2.54
(.100)
.635
(.020)
.762
(.030)
NOTES:
1. Provided with lockwasher and mounting nut.
2. Recommend panel holes. #10 drill (.194).
20.32
(.80)
6.35
(.25)
#10-32 UNF-2A THD.
2.54
(.100)
7.92
(.312)
PANEL MAX.
NOTES:
1. Provided with lockwasher and mounting nut.
2. Recommend panel hole size .200 dia. (#7 drill).
MAX.
LONG
WIDE
DEEP 3.30
(0.13)
ADJ. SLOT
2.54
(.100 )
.508
(.020)
.762
(.030)
LONG
WIDE
DEEP
Notes:
1. Provided with lockwasher and
mounting nut.
2. Recommended panel holes. #10 drill
.194
(.008)
Notes:
1. Provided with lockwasher and
mounting nut.
2. Recommended panel holes. #7 drill
.200
(.008)
RT22/RTR22/RJ22 3250/3252 RT24/RTR24/3290
H and W Styles - 3290
X & W Styles-RT24/RTR24
3292
X, L and W Styles
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
Factory Installed Panel Mount
6.10
(.240)
3.05
(.120)
BUSHING
10-32 UNF-2A
THD.
OPT. BEND
DOWN ANTI-
ROTATION TAB
6.35
(.250)
10.92
(.430)
.826 ± .038
(.033 ± .020)
11.68
(.460)
PANEL
3.3
(.130)
MAX
7.37
(.290)
OPTIONAL FOR
ANTI-ROTATION NUB
= 7 DRILL
PANEL LAYOUT
NOTES:
1. Provided with lockwasher and mounting nut.
7.62
(.300)
4.06
(.160)
BUSHING
10-32 UNF-2A
THD.
OPT. BEND
DOWN ANTI-
ROTATION TAB
13.97
(.550)
11.43
(.450)
14.99
(.590)
10.16
(.400)
PANEL LAYOUT
NOTES:
1. Provided with lockwasher and mounting nut.
6.10
(.240)
3.05
(.120)
BUSHING
10-32 UNF-2A
THD.
OPT. BEND
DOWN ANTI-
ROTATION TAB
11.43
(.450)
.826 ± .038
(.033 ± .020)
11.68
(.460)
PANEL LAYOUT
NOTES:
1. Provided with lockwasher and mounting nut.
ADJ. SLOT
.243
(.010)
.064
(.003)
.064
(.003)
LONG
WIDE
DEEP
.200
(.008)
.132
(.005) OPTIONAL FOR
ANTI-ROTATION NUB
= 7 DRILL
.200
(.008)
.132
(.005)
OPTIONAL FOR
ANTI-ROTATION NUB
= 7 DRILL
.200
(.008)
.132
(.005)
7.37
(.290)
6.35
(.250)
PANEL
3.3
(.130)
MAX
6.35
(.250)
PANEL
3.3
(.130)
MAX
ADJ. SLOT
.243
(.010)
.064
(.003)
.064
(.003)
LONG
WIDE
DEEP
ADJ. SLOT
.243
(.010)
.064
(.003)
.064
(.003)
LONG
WIDE
DEEP
Notes:
1. Provided with lockwasher and
mounting nut.
Notes:
1. Provided with lockwasher and
mounting nut.
Notes:
1. Provided with lockwasher and
mounting nut.
10.0
(.394)
HEX NUT AND
LOCKWASHER
10.31
(.406)
MAX.
7.95
(.313) 33.35
(1.31)
6.35
(.250)
TO
BUSHING
10-32
NF-2 THD
5.94
(.234)
NOTES:
1. Provided with lockwasher and mounting nut.
2. Recommend panel holes. #10 drill (.194).
7.62
(.300)
4.06
(.160)
BUSHING
10-32 UNF-2A
THD.
OPT. BEND
DOWN ANTI-
ROTATION TAB
6.35
(.250)
13.97
(.550)
11.43
(.450)
14.99
(.590)
10.16
(.400)
PANEL LAYOUT
NOTES:
1. Provided with lockwasher and mounting nut.
2. Drawings shown with trimmer. Order part separately.
22.10
(.870)
7.62
(.300)
5/16-32
UNEF
THREAD
5.54
(.218)
9.53
(.375)
9.53
(.375)
ADJ. SHAFT
RECESSED 5/16
NOTES:
1. Drawings shown with trimmer. Order part separately.
ADJ. SLOT
.243
(.010)
.064
(.003)
.064
(.003)
LONG
WIDE
DEEP
1.52
(.060)
3.30
(.130) PANEL MAX.
3.30
(0.13)
ADJ. SLOT
2.54
(.100)
.635
(.250)
.762
(.030 )
LONG
WIDE
DEEP
= 7 DRILL
.200
(.008)
OPTIONAL FOR
ANTI-ROTATION NUB
.132
(.005)
H-83P Panel Mount
Adapter for Models 3005 and 3006
The H-83P Adapter is used with Models
3005 and 3006. Order separately and
simply snap t the trimmer in the plastic
case. The H-83P with lockwasher and
mounting nut is available in 50-piece
lots.
H-58P Panel Mount
1-1/4 Inch Rectangular
Multiturn Modules
Notes:
1. Provided with lockwasher and
mounting nut.
2. Drawings shown with trimmer. Order
part separately.
Notes:
1. Drawings shown with trimmer. Order
part separately.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
Customer Installed Panel Mount - Unsealed
SEE TABLE II FOR PANEL MOUNT PART NUMBER
H-65P Panel Mount
1/2 Inch Square
Multiturn Models
Notes:
1. Provided with lockwasher and
mounting nut.
2. Recommended panel holes. #10 drill
.194
(.008)
*Specify H82 if panel seal is required.
H-114P/115P/116P Panel Mount
3/8 Inch Square Multiturn Models
Notes:
1. Provided with lockwasher and
mounting nut.
2. Drawings shown with trimmer. Order
part separately.
H-117P Panel Mount
3/8 Inch Square Multiturn Models
Notes:
1. Provided with lockwasher and
mounting nut.
2. Drawings shown with trimmer. Order
part separately.
Customer Installed Panel Mount
6.10
(.240)
3.05
(.120)
BUSHING
10-32 UNF-2A
THD.
OPT. BEND
DOWN ANTI-
ROTATION TAB
6.35
(.250)
10.92
(.430)
(H-114P)
11.68
(.460)
7.37
(.290)
PANEL LAYOUT
NOTES:
1. Provided with lockwasher and mounting nut.
2. Drawings shown with trimmer. Order part separately.
11.43
(.450)
(H-115P)
(H-116P)
ADJ. SLOT
.244
(.096)
.0635
(.025)
.0635
(.025)
LONG
WIDE
DEEP
8.179
(.322)
(H-115P)
(H-116P)
8.255
(.325)
(H-114P)
PANEL MAX.
3.30
(0.13)
= 7 DRILL
5.08
(.200)
OPTIONAL FOR
ANTI-ROTATION NUB
.132
(.005)
6.86
(.270)
4.06
(.160)
BUSHING
10-32 UNF-2A
THD.
6.10
(.240)
8.76 ± .38
(.345 ± .015)
11.68
(.460)
7.62
(.300)
PANEL LAYOUT
NOTES:
1. Provided with #10 spring lockwasher and hex nut.
2. Drawings shown with trimmer. Order part separately.
11.68
(.460)
ADJ. SLOT
2.44
(.096)
.635
(.025)
.635
(.025)
DIA.
WIDE
DEEP
2.54
(.100)
REF.
2.54
(.100)
REF.
5.72
(.225)
REF.
DIA.
5.08
(.200)
OPTIONAL FOR
ANTI-ROTATION LUG
1.32
(.052)
TABLE I
FACTORY INSTALLED
PANEL MOUNTS
P/N WITH
STANDARD P/N PANEL MOUNT
3005P-1-(RC) 3005P-1-(RC) Z
3006P,Y, or W-1-(RC) 3006P,Y, or W-1-(RC) Z
3009P or Y-1-(RC) 3009P or Y-1-(RC) Z
3057L,J,P, or Y-1-(RC) 3057L,J,P, or Y-1-(RC) M
3059L,J,P, or Y-1-(RC) 3059L,J,P, or Y-1-(RC) M
3250L or W-1-(RC) 3250L or W-1-(RC) M
3252L or W-1-(RC) 3252L or W-1-(RC) M
3290 H or W-1-(RC) 3290H or W-1-(RC) M
3292L,W, or X-1-(RC) 3292L,W, or X-1-(RC) M
3296W or X-1-(RC) 3296W or X-1-(RC) M
TABLE II
RETRO-FIT PANEL MOUNTS FOR
INSTALLATION BY CUSTOMER
ORDER PANEL MOUNT
STANDARD P/N P/N
3005P-1-(RC) H-83P
3006P,Y, or W-1-(RC) H-83P
3057L,J,P, or Y-1-(RC) H-58P* SCREW ASSY.
3059L,J,P, or Y-1-(RC) H-58P* SCREW ASSY.
3250L, W, X-(RC) H-65P-1*
3252L or W-1-(RC) H-65P-3*
3252X-1-(RC) H-65P-5*
3290 H or W-1-(RC) H-114P*
3292L-1-(RC) H-115P*
3292W OR X-1-(RC) H-116P*
RT12P,Y,L H-58P* SCREW ASSY.
RJ12P,Y H-58P* SCREW ASSY.
RT22L,W, X,
RTR22L,W, X H-65P-1*
RJ22L,W H-65P-3*
RJ22X H-65P-5*
RT24W /
RTR24W OR X H-114P*
RJR24W OR X H-117P*
*Specify H-82 if panel seal is required.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
7.37
(.290)
3.81
(.150)
4.83
(.190)
.381
(.015)
1.02
(.040)
STAINLESS STEEL
CUP WASHER
.89
(.035)
RUBBER O RING
B
C
A
9.35
(.368)
9.35
(.368)
4.57
(.180)
12.70
(.500) 23.62
(.930)
4 PLCS.
13.21
(.520)
4.01
(.158)
6.35
(.250)
6.35
(.250)
.325
(.013)
DIA.
2 PLCS.
6.35
(.250)
15.88
(.625)
4.83
(.190)
TYP.
H-82 Panel Seal
For all panel mounts with size 10-32
bushings.
To be used with the following to provide
panel seal:
H-58P
H-65P-1
H-65P-3
H-65P-5
H-114P
H-115P
H-116P
H-117P
Hardware For Special Mounting Applications
H-25/H-28 Stacking Straps
Models 3250, 3252 (H-25) and 3292
(H-28).
DIMENSIONS H-25 H-28
A .236 .178
(.093) (.070)
B .363 .318
(.143) (.125)
C 1.321 1.064
(.520) (.419)
THICKNESS .51
(.02)
REV. 11/17
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns® products manufactured by or on behalf of Bourns, Inc. and
its aliates (collectively, “Bourns”).
Unless otherwise expressly indicated in writing, Bourns® products and data sheets relating thereto are subject to change
without notice. Users should check for and obtain the latest relevant information before placing orders and should verify that
such information is current and complete.
The characteristics and parameters of a Bourns® product set forth in its data sheet are based on laboratory conditions, and
statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical
requirements in generic applications. The characteristics and parameters of a Bourns® product in a user application may vary
from the data sheet characteristics and parameters due to a combination of the Bourns® product with other components in
the user’s application or due to the environment of the user application itself. Such characteristics and parameters also can
and do vary in dierent applications and actual performance may vary over time. Users should always verify actual performance
of the Bourns® product in their specic devices and applications, and make their own independent judgments about how
much additional test margin to design in to compensate for dierences between laboratory and real world conditions.
Unless Bourns has explicitly designated an individual Bourns® product as meeting the requirements of a particular industry
standard (e.g., ISO/TS 16949) or a particular qualication (e.g., UL listed or recognized), Bourns is not responsible for any
failure of an individual Bourns® product to meet requirements of such industry standard or such particular qualication. Users
of Bourns® products are responsible for ensuring compliance with safety-related requirements and standards applicable to
their applications.
Bourns® products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining
applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property
or environmental damage. Unless expressly and specically approved in writing by two authorized Bourns representatives on
a case-by-case basis, use of any Bourns® products in such unauthorized applications is at the user’s sole risk. Life-critical
applications include devices identied by the U.S. Food and Drug Administration as Class III devices and generally equivalent
classications outside of the United States.
Bourns® standard products that are designed and tested for use in automotive applications will be described on the applicable
data sheets as compliant with the applicable AEC-Q standard. Unless expressly and specically approved in writing by two
authorized Bourns representatives on a case-by-case basis, use of any other Bourns® standard products in an automotive
application is not recommended, authorized or intended and will be at the user’s sole risk.
Bourns® standard products are not tested to comply with United States Federal Aviation Administration standards generally
or any other generally equivalent governmental organization standard applicable to products designed or manufactured for
use in aircraft or space applications. Bourns® standard products that are designed and tested for use in aircraft or space
applications will be described on the applicable data sheets as compliant with the RTCA DO-160 standard. Unless expressly
and specically approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other
Bourns® standard product in an aircraft or space application is not recommended, authorized or intended and will be at the
user’s sole risk.
The use and level of testing applicable to Bourns® custom products shall be negotiated on a case-by-case basis by Bourns
and the user for which such Bourns® custom products are specially designed. Absent a written agreement between Bourns
and the user regarding the use and level of such testing, the provisions above applicable to Bourns® standard products shall
also apply to such Bourns® custom products.
Users shall not sell, transfer, export or re-export any Bourns® products or technology for use in activities which involve the
design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use
Bourns® products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions
apply to all uses and applications that violate national or international prohibitions, including embargos or international
regulations. Further, Bourns® products, technology or technical data may not under any circumstance be exported or
re-exported to countries subject to international sanctions or embargoes, and Bourns® products may not, without prior
authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible to
receive U.S. commodities, software, and technical data.
To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability arising out of the application or
use of any Bourns® standard product, (ii) any and all liability, including, without limitation, special, punitive, consequential
or incidental damages, and (iii) any and all implied warranties, including implied warranties of tness for particular purpose,
non-infringement and merchantability.
For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplied Chinese
bilingual versions are available at:
Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies
PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf
C1753 10/18/17